Search Results

Search found 13727 results on 550 pages for 'gnome tweak tool'.

Page 172/550 | < Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179  | Next Page >

• squid running out of sockets

  - by drscroogemcduck

  I have a setup where squid sits in front of a java server and acts as a reverse proxy. Recently i've load tested the site and if i fire 100 threads at it each making a request using jmeter i start getting errors in my load test tool like 'no route to host' even though the load test tool and the server are on the same machine. if i run the following command where port 82 is the port my squid server is running on: netstat -ann | grep 82 | wc -l i get 22000 or something and most of them are in TIMED_WAIT. i'm thinking that maybe the huge number of sockets in the TIMED_WAIT state are starving the box of resources.

  Read the article

• Need decent undelete utility for Windows

  - by Michael Chermside

  So I get the phone call from a friend or relative or client: "Looks like I accidentally deleted 4 years worth of accounting data. Oh, and I don't have any backups. Can you help?" What I need is a good Windows tool (for NTFS I think) that scans blocks marked as deleted and attempts to recover the file. And I need one that can be run from a thumb drive or since installing new software has a decent chance of overwriting the data before it can be recovered. Googling for such tools turns up mostly carefully-crafted advertisements for moderately expensive products with a "Free! Demo! Version!" which is not exactly reassuring. Any recommendations for a good tool?

  Read the article

• How to increase the disk cache of Windows 7

  - by Mark Christiaens

  Under Windows 7 (64 bit), I'm reading through 9000 moderately sized files. In total, there is more than 200 MB of data. Using Java (JDK 1.6.21) I'm iterating over the files. The first 1400 or so go at full speed but then speed drops off to 4ms per file. It turns out that the main cost is incurred simply by opening the files. I'm opening the files using new FileInputStream (and of course closing them in time to avoid file leaks). After some investigating, I see that Windows' disk cache is using only 100 MB or so of RAM although I have 8 GiB available. I've tried increasing the cache size using the CacheSet tool but any values I provide are considered out of range. I've also tried enabling the LargeSystemCache registry key but (after rebooting) the CacheSet tool still indicates I'm using 100 MB of cache (and doesn't increase during the test run). Does anybody have any suggestions to "encourage" Windows 7 to cache my 9000 files?

  Read the article

• Anyone interested in obtaining a cable list from a visio Diagram? [closed]

  - by Alex

  it's my first post here. Just wondering if anyone had to deal with the following problem - you have to install over say a 100 network elements and servers - cabling is done via contractors, so you need to provide them with an accurate, error-free cable list - your inputs are a set of detailed, port by port, visio diagrams. Prb is to obtain the cable list and get the cabling started while you're busy crafting the switch/routers configs. I coded a Visio plugin, which I plan to release under the GNU license, that returns a cable list from a diagram, and tested it on intermediate size infrastructure, 2K+ cables. It works well. The tool needs a little work to be user friendly, so before getting started, I wanted to know if that was worth the effort. Questions are welcomed, let me know -A PS: the tool is targeted for those who need a port by port description of their network, in the form Source/slot/port/Destination/slot/port.

  Read the article

• Fix NTFS partition

  - by stolebe

  Okay, so i was about to resize one of my NTFS partitions but suddenly the partition tool showed me an error and it crashed, so i was no longer able to use my partition - even when i tried mounting it under linux it showed me error. I installed active partition recovery, and using it i can see all my files on that partition - it's all there, nothing's been removed. I just need somehow to fix the partition so it can be usable again. Can you tell me how, or using with which tool/software ? Thank you.

  Read the article

• Reconnoiter - Anyone using it?

  - by Marco Ramos

  Reconnoiter is a new tool in the world of monitoring. It is not only a trending tool but also alerting/fault detection one. In my particular case, I reckon that it's in the trending capacities that Reconnoiter has a very huge potential. One of the premises Recoinnoter is built upon is that RRDTool large installations are very inneficient regarding I/O and I think this is RRDTool major problem. One of the things that would make me change from Cacti is, obviously, the cost of change and the learning curve. So, any of you has experience with Reconnoiter? How's the learning curve? Was it difficult to move from RRDTool frontend applications (Cacti, Munin, Ganglia) to Reconnoiter? I'm looking forward to read your opinions.

  Read the article

• Bridging a Windows 7 and Ubuntu dual boot inside an OS

  - by matsko

  I have Windows 7 and Ubuntu installed on my local PC. They're both installed on separate partitions on the same machine, and when the computer boots up the user is given the option to choose which one they want to boot use as the OS. This all works fine, but I want to use Windows 7 instead of Ubuntu, I am required to restart the computer and boot up the other OS. Is is possible to use an "inline" tool that will allow to change between both OSs as if they were windows in Windows 7? Which tool would that be? Does anyone know of anything else than Parallels? Also are there any free tools that would do this?. Many Thanks.

  Read the article

• The best software for users internet usage

  - by nikospkrk

  Hi, We are a small business using a Vigor 2820 as the internet router, and we'd like to install a software that could report any internet usage from our users. I already tried the "official" software made by Draytek called "SmartMonitor", but is reliability is a real issue as it doesn't seem to keep capturing packets after working 3 to 6hours (randomly), whereas Wireshark keeps capturing packets after that amount of time. As I'm really fed up with this tool, I'm looking for other solutions but I still want the same features: users statistics, websites ranking, users traffic, ... I already enabled the port mirroring feature, so it would be perfect if you could suggest me a port mirroring-based software (ideally freeware). I thought I had found the good one with Etherscout, but it just doesn't launch. I am even open to a tool that would "just" make some reports based on Wireshark captured files (*.pcap). Thank you for any of your suggestion, Nicolas.

  Read the article

• Dump memory of process in Window 7?

  - by abmv

  Is there any tool to dump the running application from memory n Windows 7?

  Read the article

• Is there a way to snip part of the screen with a hotkey?

  - by Head of Catering

  I'm able to launch the snipping tool, select an option and then copy based on my selection. Is there a way to launch a default snipping option so that I can create partial screen screenshots without using a third-party tool? Essentially, I'm looking for winkey+S without having to use OneNote. Both OneNote and SnagIt implement this perfectly. If OneNote is running, pressing winkey+S allows me to click and drag any portion of the screen, including pop-out menus with selections that are active. SnagIt does almost the exact same thing, invoked by the prt screen key.

  Read the article

• Tools to automate recording streaming radio

  - by Stan

  Are there any tools that can automate recording online streaming radio? I've been using Total Recorder which has the following useful features: Handy scheduler Supports creating recording templates, so I can customize some high/low quality recording Unfortunately it requires opening the streaming radio in a browser and can't have another sound source at the same time; it's recording what comes out from the speaker. What I am looking for is given an online radio URL, the tool should be able to record the audio stream, no matter if I am playing any other music or not. Does such a tool exist?

  Read the article

• Selectively allow NetBIOS inbound traffic

  - by shayan

  This is what I try to achieve from a very high point of view: Every time someone tries to access my shared folders (on Windows) a popup should open and ask for my permission. Do you know any tool? Something like "NetShareMonitor" is helpful for monitoring only A tool like an Antivirus these days has a focus on outgoing traffic A normal firewall does not allow me to select at the time of request. Setting User Permissions is not an option, I want to allow/deny at the time of request even if it is the same user over and over again.

  Read the article

• How to tell which physical disks have bootable MBR?

  - by Jon

  The computer I am using right now has 6 physical disks attached. Using the BIOS's "select boot device" functionality I have discovered that I can boot off 3 of these disks into the exact same bootloader. This means that all of these disks have the bootable flag set on their MBR, even though I had been under the impression that only 2 of them are in fact bootable. My question is: is there an easy way to check which disks have a bootable MBR with a command line tool or some OS utility? I am aware of the DISKPART tool and its basic functionality, but I haven't found how to view the information I need. The OS is Windows 7 x64 Ultimate with SP1.

  Read the article

• update ocz vertex le capacity via firmware update

  - by Ben Voigt

  I have an OCZ Vertex LE 100GB drive. It's actually 128GiB of NAND flash, with a whopping 28%+ reserved for write combining. Most 128GiB drives are actually ~ 115GB usable (and marketed as 120GB or 128GB). There were rumors that the reserved fraction could be decreased on OCZ 100GB drives. Can anyone provide a link to firmware that does that, or an official statement that no such firmware exists? (NB: I recently installed the 1.24 firmware from the OCZ site, it didn't affect the capacity. Possibly because the rumors say the capacity change is destructive to existing content.) Of possible interest: flashing firmware was more of a pain than it should have been -- the tool didn't detect the disk until I booted an older Windows install off a secondary hard disk, I suspect the Intel SATA driver is the issue and tool only works with the msachi.sys driver.

  Read the article

• Unable to delete all partitions on flash drive using Windows 7 OS??

  - by irrational John

  Recently I purchased an ADATA C802 8GB flash drive. Since the drive was new I decided to run some of the HD Tune Pro (v4.50) performance tests on it, mostly just for the heck of it. To avoid accidently destroying data HD Tune refuses to write to a drive unless there are no partitions on the drive. If you do attempt to write to a drive with partitions, it posts the message "Writing is disabled. To enable writing please remove all partitions." As you would expect, the ADATA came formatted with a single primary FAT32 partition in the Master Boot Record. But a number of unexpected things happened when I attempted to delete that partition. The first thing I tried was to use the Windows 7 (64-bit) Disk Management tool (diskmgmt.msc) to delete the partition. It would not let me. The context menu choice to delete that volume was not available. Next I opened up a command prompt window with Admin authority and ran diskpart. Diskpart deleted the volume for me. However, when I attempted to run an HD Tune write test on the drive I still got the "Writing is disabled" message. Huh??? So I fired up a utility I have which allows viewing drives at the sector level and verified that the partition table in the Master Boot Record was empty. No partitions. Yet HD Tune still thought there were partitions on the drive? So why was I still getting the "Writing is disabled" message from HD Tune Pro? And why wouldn't the Windows 7 Disk Management tool let me change the partitions on this drive. After doing the above, I plugged the ADATA into my MacBook. I was then able to format it as either a GPT or MBR partitioned drive with no problems. I am not looking for suggestions on how to format this drive. I can do that. What I do not understand and was hoping I might get insight into is why this drive behaves so strangely under Windows 7? And BTW, what's up with HD Tune Pro? BTW, if I plug the drive I formatted on my MacBook back into my Windows 7 64-bit system I still run into road blocks with the Disk Management tool. For example, I cannot delete all the GPT partitions on the ADATA so I can convert it into an MBR drive. I following Microsoft's instructions, the instructions just do not work with this ADATA flash drive. Anyone know what's up with this? It makes no sense to me. Has something changed in Windows 7 (Vista)??

  Read the article

• Remote kill, upload, execute file

  - by Masoud M.

  I'm developing a program and I need to upload my xyz.exe file to many host machines and execute them frequently. I need a server-client tool to do it as below steps after an update signal from my PC: Those host machine should kill any running processes with name xyz.exe. Download my new xyz.exe. Then execute new xyz.exe. I know about some tools like PsExec, but I need a tools with better user-interface and more powerful. Is there any tool to do it ? UPDATE: The systems are in a same LAN, OS is windows (XP or 7), No full remote access is needed. I'm a developer and my program should run in remote hosts and I'm testing my application.

  Read the article

• import macintosh thunderbird emails to windows email

  - by Ryan

  My mac laptop died. The hard drive is good. I am able to pull what I need off my mac and copy it to windows using an open source tool (I forgot the name of it). I need my old mac emails. I was using the macintosh thunderbird for emails. How do I load those emails into thunderbird, outlook, or any other windows email tool? I did google this and there were some brief explanations, but they did not work. The vast majority of posts are about going from windows to mac.

  Read the article

• Configuring BitLocker on existing Windows Server 2008

  - by neildeadman

  On our file server, we want to enable BitLocker so that we can encrypt a single drive and I know that we have to also encrypt the drive the system is installed on. In my tests with VMs, I have to create a partition on the same disk as Windows is installed either before I install Windows or after (I can use the BitLocker Drive Preparation Tool). This tool shrinks the C: drive to make way for a 1.5GB partition. I'm a little concerned about doing this with a live system so wanted to see if it was possible to get BitLocker to use a partition on another drive?

  Read the article

• Update notification for macports

  - by Space_C0wb0y

  Is there any way or tool that I can use to receive notifications when any of my macports-packages are out-of-date?

  Read the article

• Cat5 wiring in my home [closed]

  - by Mike

  I have problem with cat5 cabling First I ran a length of cable 30 metres to my bedroom 1 and and connected both ends to a wall sockets internally using my punch down tool, both ends look fine. I also ran a cable from bedroom 1 to bedroom 2 so my son can use same internet connection , i then parallel connected my cables in bedroom 1 against using punch down tool using same colours all the way through. I ran a Ethernet cable from modem to first wall socket close to it then at bedroom end used another Ethernet cable to connect pc, it wouldn't connect to pc so I disconnected bedroom 2 cable from bedroom 1 socket. I connected bedroom 1 to pc and it worked, but how do I connect bedroom 2 (obviously cat 5 cable bedroom 1 to 2 is in place) As soon as I connect one wire from bedroom2 I loose Internet connection!

  Read the article

• split large text file without missing data record

  - by Santosh

  I have a 140 MB text file, which contains detail information of books in library. For each book details there is a standard format data details in text file. I need to parse it and insert the data in Database. Here, parsing text file is not an issue. I am facing problem in parsing this large file. So i decided to split the file in small file around 2 MB each file. But i can't manually split this large file in so many pieces. I got HJsplit tool, which split the file but this also doesn't helped as this split the file but 1 book details half part is in one file and rest part is in second file. so if i split this way then information will be missed. How to split the large so that i cant miss the information ? Is there any tool which help me in this condition.

  Read the article

• What tools can be used to download all images in a webpage?

  - by bobo

  I would like to download all images in a web page. The tool should be smart enough to examine the css and javascript files in the page source to look for the images. Ideally, it should also replicate the folder hierarchy, saving the images in the correct folder. For example, the web page may have some images for menu items stored in images/menu/ and for background images it may be stored in images/bg/. Is there such a tool that you know of? (preferably in Windows but Linux is still ok) Many thanks to you all.

  Read the article

• free Raw-File Converter/Editor

  - by RCIX

  I have RAW files output by a program with a specific set of properties (Photoshop RAW, 16 bits, IBM PC byte order, no header, 1 non-interleaved channel, variable sizes like 257X257 or 129X513); does anyone know of a free tool that will allow me to convert to and from this format, and possibly do basic editing (selection, copy/paste, rotation of selection)? I've tried Picasa, XNView, and Paint Shop Pro 7 and none of them work properly. The closest i get is Paint Shop Pro which will at least make a serviceable attempt to open these files but i can't set all of the proper settings. XNView just might be able to edit it if i can figure out how to change the open settings for a particular raw file. So my questions at current are: how do i tell XNView to open a raw file a particular way? Failing that, is there any free tool that can open Photoshop-RAW files with the above settings (that's not photoshop)? If it helps, i'm trying to import/export/edit hieghtmap data for maps for Supreme Commander.

  Read the article

• Copy/move EBS volume from one Region to another

  - by Gnanam

  Background of our setup: We've hosted our web-based application in Amazon EC2 US East (Virginia) Region. Our instance is based on Linux distribution (CentOS) and AMI is S3-backed. 1 EBS volume (400 GB size) is attached to this instance. Question: We've planned to migrate our deployment to US West (N. California) Region. From AWS doc, I understood that for moving AMI, there is a command-line tool available - ec2-migrate-bundle. But for moving EBS volume across Region, currently there is no tool available. I'm looking for easiest and/or fastest way of copying/moving EBS volume from one Region to another. Also, are there any hidden risks involved during and/or after the migration? Experts ideas/suggestions/recommendations on this are highly appreciated.

  Read the article

• Simulating network latency for localhost connection on Windows 7

  - by nitro2k01

  I need to simulate network latency to a program running on the local computer, connecting to a local service. Thus far I have tried dummynet (a windows build of ipfw) which I got working after some trial and error. While it generally works, I can't seem to get it to filter localhost traffic. Even after adding a rule from any to any which affects external traffic, this makes no difference for local connections. I would appreciate if anyone knows how to simulate local latency using dummynet or a different tool. The tool should be able to simulate latency generically in IP packets, (TCP and UDP) and not be protocol specific.

  Read the article

< Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179  | Next Page >