Search Results

Search found 6670 results on 267 pages for 'speed dial'.

Page 172/267 | < Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179  | Next Page >

• Copy to USB memory stick really slow?

  - by Eloff

  When I copy files to the USB device, it takes much longer than in windows (same usb device, same port) it's faster than USB 1.0 speeds (1MB/s) but much slower than USB 2.0 speeds (12MB/s). To copy 1.8GB takes me over 10 minutes (it should be < 3 min.) I have two identical SanDisk Cruzer 8GB sticks, and I have the same problem with both. I have a super talent 32GB USB SSD in the neighboring port and it works at expected speeds. The problem I seem to see in the GUI is that the progress bar goes to 90% almost instantly, completes to 100% a little slower and then hangs there for 10 minutes. Interrupting the copy at this point seems to result in corruption at the tail end of the file. If I wait for it to complete the copy is successful. Any ideas? dmesg output below: [64059.432309] usb 2-1.2: new high-speed USB device number 5 using ehci_hcd [64059.526419] scsi8 : usb-storage 2-1.2:1.0 [64060.529071] scsi 8:0:0:0: Direct-Access SanDisk Cruzer 1.14 PQ: 0 ANSI: 2 [64060.530834] sd 8:0:0:0: Attached scsi generic sg4 type 0 [64060.531925] sd 8:0:0:0: [sdd] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB) [64060.533419] sd 8:0:0:0: [sdd] Write Protect is off [64060.533428] sd 8:0:0:0: [sdd] Mode Sense: 03 00 00 00 [64060.534319] sd 8:0:0:0: [sdd] No Caching mode page present [64060.534327] sd 8:0:0:0: [sdd] Assuming drive cache: write through [64060.537988] sd 8:0:0:0: [sdd] No Caching mode page present [64060.537995] sd 8:0:0:0: [sdd] Assuming drive cache: write through [64060.541290] sdd: sdd1 [64060.544617] sd 8:0:0:0: [sdd] No Caching mode page present [64060.544619] sd 8:0:0:0: [sdd] Assuming drive cache: write through [64060.544621] sd 8:0:0:0: [sdd] Attached SCSI removable disk

  Read the article

• Partner Webcast - Oracle Data Integration Competency Center (DICC): A Niche Market for services

  - by Thanos Terentes Printzios

  Market success now depends on data integration speed. This is why we collected all best practices from the most advanced IT leaders, simply to prove that a Data Integration competency center should be the primary new IT team you should establish. This is a niche market with unlimited potential for partners becoming, the much needed, data integration services provider trusted by customers. We would like to elaborate with OPN Partners on the Business Value Assessment and Total Economic Impact of the Data Integration Platform for End Users, while justifying re-organizing your IT services teams. We are happy to share our research on: The Economical impact of data integration platform/competency center. Justifying strongest reasons and differentiators, using numeric analysis and best-practice in customer case studies from specific industries Utilizing diagnostics and health-check analysis in building a business case for your customers What exactly is so special in the technology of Oracle Data Integration Impact of growing data volume and amount of data sources Analysis of usual solutions that are being implemented so far, addressing key challenges and mistakes During this partner webcast we will balance business case centric content with extensive numerical ROI analysis. Join us to find out how to build a unified approach to moving/sharing/integrating data across the enterprise and why this is an important new services opportunity for partners. Agenda: Data Integration Competency Center Oracle Data Integration Solution Overview Services Niche Market For OPN Summary Q&A Delivery Format This FREE online LIVE eSeminar will be delivered over the Web. Registrations received less than 24hours prior to start time may not receive confirmation to attend. Presenter: Milomir Vojvodic, EMEA Senior Business Development Manager for Oracle Data Integration Product Group Date: Thursday, September 4th, 10pm CEST (8am UTC/11am EEST)Duration: 1 hour Register Today For any questions please contact us at [email protected]

  Read the article

• Internet slow on one router only [the problem only in Ubuntu] [on hold]

  - by mrSuperEvening

  Internet works perfectly on every other router, but browsing sucks at home (slow browsing and slow loading times). I changed DNS servers to 8.8.0.0, still doesn't help. And funnily, download speed is extremely high on this network (meaning torrents for example), but using browsers and loading websites is extremely slow (only on this network). Do I need to change something in router settings or what can I try? By the way, I use wired connection to router. EDIT: There's no problems when using Windows. EDIT: ifconfig: eth0 Link encap:Ethernet HWaddr f2:4d:a0:c0:3f:4c inet addr:192.168.11.8 Bcast:192.168.11.255 Mask:255.255.255.0 inet6 addr: fe80::f24d:a2ff:fec6:3f4c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:206798 errors:0 dropped:0 overruns:0 frame:0 TX packets:219570 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:76680734 (76.6 MB) TX bytes:21738160 (21.7 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:160 errors:0 dropped:0 overruns:0 frame:0 TX packets:160 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11094 (11.0 KB) TX bytes:11094 (11.0 KB)` ping -c 2 4.2.2.2 PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data. --- 4.2.2.2 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms ping -c 2 google.com PING google.com (213.159.32.147) 56(84) bytes of data. 64 bytes from lan-213-159-32-147.kns.skynet.lv (213.159.32.147): icmp_seq=1 ttl=61 time=0.936 ms 64 bytes from lan-213-159-32-147.kns.skynet.lv (213.159.32.147): icmp_seq=2 ttl=61 time=0.937 ms --- google.com ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms rtt min/avg/max/mdev = 0.936/0.936/0.937/0.030 ms

  Read the article

• Rotating wheel with touch (adding momentum and slowing down the initial rate it can be moved

  - by Lewis

  I have a wheel control in a game which is setup like so: - (void)ccTouchesMoved:(NSSet *)touches withEvent:(UIEvent *)event { UITouch *touch = [touches anyObject]; CGPoint location = [touch locationInView:[touch view]]; location = [[CCDirector sharedDirector] convertToGL:location]; if (CGRectContainsPoint(wheel.boundingBox, location)) { CGPoint firstLocation = [touch previousLocationInView:[touch view]]; CGPoint location = [touch locationInView:[touch view]]; CGPoint touchingPoint = [[CCDirector sharedDirector] convertToGL:location]; CGPoint firstTouchingPoint = [[CCDirector sharedDirector] convertToGL:firstLocation]; CGPoint firstVector = ccpSub(firstTouchingPoint, wheel.position); CGFloat firstRotateAngle = -ccpToAngle(firstVector); CGFloat previousTouch = CC_RADIANS_TO_DEGREES(firstRotateAngle); CGPoint vector = ccpSub(touchingPoint, wheel.position); CGFloat rotateAngle = -ccpToAngle(vector); CGFloat currentTouch = CC_RADIANS_TO_DEGREES(rotateAngle); wheelRotation += (currentTouch - previousTouch) * 0.6; //limit speed 0.6 } } Now once the user lets go of the wheel I want it to rotate back to where it was before but not without taking into account the momentum of the swipe the user has done. This is the bit I really can't get my head around. So if the swipe generates a lot of momentum then the wheel will carry on moving slightly in that direction until the overall force which pulls the wheel back to the starting position kicks in. Any ideas/code snippets?

  Read the article

• How do I interpolate air drag with a variable time step?

  - by Valentin Krummenacher

  So I have a little game which works with small steps, however those steps vary in time, so for example I sometimes have 10 Steps/second and then I have 20 Steps/second. This changes automatically depending on how many steps the user's computer can take. To avoid inaccurate positioning of the game's player object I use y=v0*dt+g*dt^2/2 to determine my objects y-position, where dt is the time since the last step, v0 is the velocity of my object in the beginning of my step and g is the gravity. To calculate the velocity in the end of a step I use v=v0+g*dt what also gives me correct results, independent of whether I use 2 steps with a dt of for example 20ms or one step with a dt of 40ms. Now I would like to introduce air drag. For simplicity's sake I use a=k*v^2 where a is the air drag's acceleration (I am aware that it would usually result in a force, but since I assume 1kg for my object's mass the force is the same as the resulting acceleration), k is a constant (in this case I'm using 0.001) and v is the speed. Now in an infinitely small time interval a is k multiplied by the velocity in this small time interval powered by 2. The problem is that v in the next time interval would depend on the drag of the last which again depends on the v of the last interval and so on... In other words: If I use a=k*v^2 I get different results for my position/velocity when I use 2 steps of 20ms than when I use one step of 40ms. I used to have this problem for my position too, but adding +g*dt^2/2 to the formula for my position fixed the problem since it takes into account that the position depends on the velocity which changes slightly in every infinitely small time interval. Does something like that exist for air drag too? And no, I dont mean anything like Adding air drag to a golf ball trajectory equation or similar, for that kind of method only gives correct results when all my steps are the same. (I hope you can understand my intermediate english, it's not my main language so I would like to say sorry for all the silly mistakes I might have made in my question)

  Read the article

• Driver for asus wireless PC card WL-100GE

  - by emab

  I have bought an Asus wireless LAN PC Card WL-100GE model, and I am using lubuntu on my system. While I have no cable connection, currently I cannot access the internet and update my laptop. Device: Broad Range Wireless Card Bus Adaptor - Asus - WL-100GE I searched the web and couldn't find any adequate driver for it. Is there any solution for it? My sudo lshw -C network output is: *-network description: Ethernet interface product: RTL-8100/8101L/8139 PCI Fast Ethernet Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:02:3f:ba:55:c8 size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=128 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:3000(size=256) memory:e0200800-e02008ff *-network description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:07:00.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:21 memory:38000000-38001fff ----:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• Modular Architecture for Processing Pipeline

  - by anjruu

  I am trying to design the architecture of a system that I will be implementing in C++, and I was wondering if people could think of a good approach, or critique the approach that I have designed so far. First of all, the general problem is an image processing pipeline. It contains several stages, and the goal is to design a highly modular solution, so that any of the stages can be easily swapped out and replaced with a piece of custom code (so that the user can have a speed increase if s/he knows that a certain stage is constrained in a certain way in his or her problem). The current thinking is something like this: struct output; /*Contains the output values from the pipeline.*/ class input_routines{ public: virtual foo stage1(...){...} virtual bar stage2(...){...} virtual qux stage3(...){...} ... } output pipeline(input_routines stages); This would allow people to subclass input_routines and override whichever stage they wanted. That said, I've worked in systems like this before, and I find the subclassing and the default stuff tends to get messy, and can be difficult to use, so I'm not giddy about writing one myself. I was also thinking about a more STLish approach, where the different stages (there are 6 or 7) would be defaulted template parameters. Can anyone offer a critique of the pattern above, thoughts on the template approach, or any other architecture that comes to mind?

  Read the article

• Need Help Hiring a Perfectionist Programmer [closed]

  - by Bryan Hadaway

  I understand my question may be in the gray area, but I'm not able to use the Meta to ask if this question is appropriate or not so I'll simply have to risk it. My project is complete in the sense that it's a fully functional, ready to go 1.0 version. However, that's not good enough for my standards. My expertise is in HTML/CSS, not jQuery and PHP. I'm looking for someone to refine every character of my code for quality, speed, security and compatibility. I want everything to be as bug free as possible for launch. So I need an expert programmer who's a perfectionist in their coding who cares about the quality of their work (not just making it work) to review and refine my code. I'm sure I can't outright post the project's details and hope for interested parties to contact me as that wouldn't be beneficial to the community so instead I'm looking for advice from programmers about where some of best places to hire quality programmers are and the best strategies to hire the right programmer. In other words, screening applicants off of craigslist isn't going to cut it for this project. Thanks

  Read the article

• Welcome!

  - by mannamal

  Welcome to the Oracle Big Data Connectors blog, which will focus on posts related to integrating data on a Hadoop cluster with Oracle Database. In particular the blog will focus on best practices, usage notes, and performance tips for using Oracle Loader for Hadoop and Oracle Direct Connector for HDFS, which are part of Oracle Big Data Connectors. Oracle Big Data Connectors 1.0 also includes Oracle R Connector for Hadoop and Oracle Data Integrator Application Adapters for Hadoop. Oracle Loader for Hadoop: Oracle Loader for Hadoop loads data from Hadoop to Oracle Database. It runs as a MapReduce job on Hadoop to partition, sort, and convert the data into an Oracle-ready format, offloading to Hadoop the processing that is typically done using database CPUs. The data is thenloaded to the database by the Oracle Loader for Hadoop job (online load) or written out as Oracle Data Pump files for load and access later (offline load) with Oracle Direct Connector for HDFS. Oracle Direct Connector for HDFS: Oracle Direct Connector for HDFS is a connector for high speed access of data on HDFS from Oracle Database. With this connector Oracle SQL can be used to directly query data on HDFS. The data can be Oracle Data Pump files generated by Oracle Loader for Hadoop or delimited text files. The connector can also be used to load data into the database using SQL.

  Read the article

• Ubuntu 12.04 still slow at mounting internal filesystem

  - by Matthew Goson

  I'm using Toshiba laptop with this configuration: - CPU: Core i5, 2.4GHz - RAM: 4GB - Graphics card: Intel - Hard disk: 500GB SATA I installed Ubuntu 12.04 64bit and got the same issue with this guy Very slow boot due to mounting filesytem, I tried all suggestions there but the slow boot issue still here. Here's a part of my dmesg: [ 2.041015] usbhid: USB HID core driver [ 2.101378] usb 1-1.6: new full-speed USB device number 5 using ehci_hcd [ 2.137980] atl1c 0000:04:00.0: version 1.0.1.0-NAPI [ 2.779080] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null) [ 22.822597] udevd[381]: starting version 175 [ 22.837954] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 22.850837] lp: driver loaded but no devices found [ 23.003822] Adding 7079096k swap on /dev/sda7. Priority:-1 extents:1 across:7079096k [ 23.407915] mei: module is from the staging directory, the quality is unknown, you have been warned. [ 23.408153] mei 0000:00:16.0: PCI->APIC IRQ transform: INT A -> IRQ 16 [ 23.408160] mei 0000:00:16.0: setting latency timer to 64 [ 23.408211] mei 0000:00:16.0: irq 44 for MSI/MSI-X [ 23.433196] [drm] Initialized drm 1.1.0 20060810 Additional information: my sda1 is a primary NTFS partition, sda2 is a primary ext4 partition which I installed Ubuntu onto. Other partitions are inside an extended partition.

  Read the article

• Which is the best image hosting site for hosting images for website? [closed]

  - by rahul dagli

  I currently have a website and blog and using a limited web hosting plan. When I upload images on my hosting server it consumes a lot of bandwidth and space. So I was thinking of hosting images on some-other image hosting site and direct linking it to my site. I found out few sites like imageshack, photobucket, tinypic, imgur. However, I see all have certain restrictions. The features i am looking for are as follows: 1. At least 10gb space 2. At least 500gb bandwidth (bec I hav very high traffic) 3. Very high speed even during heavy load like 1000 visitors accessing every hour. 4. Ultra reliable servers (99.9% uptime) 5. Privacy control 6. Must not ever delete image if inactive 7. Create and manage albums 8. Company that will last long in business atleast for next 10 years. 9. Free of cost 10. Hotlinking/ Directlinking image.

  Read the article

• Lenovo v570 ubuntu 12.04 wireless hard blocked even when ext. switch is on

  - by user100987

  When I run iwconfig it say's lo and eth0 have no wireless extensions, but wlan0 it says IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS the:off Fragment the:off Power Management:off and I believe that's my problem, I just don't know how to turn it back on Any help? When I ran lspci | grep Network it gave me this 02:00.0 Network controller: Intell Corporation Centrino Wireless -N + WiMAX 6150 (rev 67) How I know that my wireless is hard blocked because when I run sudo rfkill list all I get 0: Ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes when I run lshw -c network I get. *-network DISABLED description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: mon1 version: 67 serial: 40:25:c2:d2:96:2c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-32-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: f0:de:f1:d7:a0:4d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.65 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff

  Read the article

• ERP/CRM Systems. Desktop Based ? Web based? [closed]

  - by Parhs

  I have seen 2-3 ERPs in action. I am wondering what is better. Desktop based application or webbased displayed on a browser. My first experience was with a web based ERP when i was 14 years old.. It was web based and terribly slow... For most simple task you had to do lots of clicks... no keyboard support ..... Pages took ages to load. Last year I worked for migrating to a newer computer some old terminal based cobol application. The computer that worked till today and still has no problem was from 1993. The user interface ofcourse was textbased.. The speed that guys placed orders was amazing! just typing the name of the customer , then 5-10 keys to add a product to order.... Comparing to this ERP the page for placing orders Link (click sales orders) seems terribly slow to add a product... No keyboard shortcut works to save what you added and generally I believe you need 4 times more time to place an order compared to the text interface... Having to use both mouse and keyboard for this task is BAD and sadistic... So how can the heck these people ever use a system like that ??? So in the long run desktop application seems the only way... Of course browsers support shortcuts but the way to overide the defaults that browsers uses isn't cross compatible... That is a huge problem. Finnaly, if we MUST/forced use cloud in near future what about keyboard shortcuts?? I feel confused... I have seen converters of desktop applications to browser applications but are SLOW as hell... The question is what about user friendliness? What kind of application would you use?

  Read the article

• Does it make sense to write build scripts in C++?

  - by Klaim

  I'm using CMake to generate my projects IDE/makefiles, but I still need to call custom "scripts" to manipulate my compiled files or even generate code. In previous projects I've been using Python and it was OK, but now I'm having serious trouble managing a lot of dependencies in two very big projects I'm working on so I want to minimize the dependencies everywhere. Someone suggested to me to use C++ to write my build scripts instead of adding a language dependency just for that. The projects themeselves already use C++ so there are several advantages that I can see: to build the whole project, only a C++ compiler and CMake would be necessary, nothing else (all the other dependencies are C or C++); C++ type safety (when using modern C++) makes everything easier to get "correct"; it's also the language I know the better so I'm more at ease with it even if I'm able to write some good Python code; potential gain in execution speed (but i don't think it will really be perceptible); However, I think there might be some drawbacks and I'm not sure of the real impact as I didn't try yet: might be longer to write the code (that said I'm not sure because I'm efficient enough in C++ to write something that work quickly, so maybe for this system it wouldn't be so long to write) (compilation time shouldn't be a problem for this case); I must assume that all the text files I'll read as input are in UTF-8, I'm not sure it can be easilly checked at runtime in C++ and the language will not check it for you; libraries in C++ are harder to manage than in scripting languages; I lack experience and forsight so maybe I'm missing advantages and drawbacks. So the question is: does it make sense to use C++ for this? do you have experiences to report and do you see advantages and disadvantages that might be important?

  Read the article

• Macbook overheats in 12.04 beta

  - by zookalicious

  Since I've heard a lot of great things about the upcoming 12.04 release, I decided to give the beta 2 a shot. Everything works very well, except ubuntu wasn't controlling the fan speed for a while. In all the past versions of ubuntu, I've just used the mactel support repository to detect my fans with the macfanctld package, and that has worked well. However it doesn't seem like that package has been updated yet for Precise, so I used the method at this Ubuntu forums thread instead. Now my computers fans are recognized and will spin up, but my laptop is getting VERY hot very frequently. Even just opening up a web browser and Libreoffice writer is enough to make the bottom of my computer feel like it's on fire and cause the fans to spin up to full. "top" shows that there are no programs eating up my CPU usage, which sometimes causes overheating. If anyone has any suggestions I would love to hear them. 12.04 is very nice and I know that for 11.10 macfanctld didn't get updated for a long time, so I'm hesitant to just wait for that.

  Read the article

• Ubuntu 12.04 Fails to Boot after Reboot

  - by Joe

  I have installed Ubuntu 12.04 on several Dell c6220 servers. The install was successful and all hardware is recognized. The problem that I am running into is that when issuing the reboot command or when pressing ctrl-alt-del, the server shuts down, but never comes back up. Instead, the fan revs up to full speed and stays that way until I power the server down. Once the server has been powered down via the power button, Ubuntu will boot just fine -- until the next reboot. I have found that by rebooting the server via the DRAC web interface will reboot the server correctly. I have also found that this problem does not exist with CentOS -- I can press ctrl-alt-del all day long and it always comes back up. I've tried several kernel parameters such as: reboot=bios reboot=pci reboot=acpi reboot=cold acpi=off noapic Nothing seems to work. I have also tried upgrading to kernel 3.4, but no change there, either. Has anyone run into a similar problem or any pointers on troubleshooting? Thanks, Joe

  Read the article

• getting started as a web developer [closed]

  - by kmote

  I have over 10 years of programming experience building (Windows-based) desktop applications and utilities (VC++, C#, Python). My goal over the next year is to start transitioning to web application development. I want to teach myself the fundamental tools and technologies that would be considered essential for building professional, online, interactive, visually-stunning, data-driven web apps -- the kind described in Google's recently released "Field Guide: Building Great Web Applications". So my question is, what are the primary, most commonly-used technologies that seasoned professionals will need in their tool belt in the coming years? My plan was to start coming up to speed in Javascript, HTML5, & CSS, and then to do a deep dive into ASP.NET and Ajax, along with SQL DBs. (I was surprised to not be able to find a single book at Amazon with a broad, general scope like this, which caused me to start second-guessing this approach.) So, seasoned professionals: am I on the right track? Are there some glaring omissions in my list? Or some unnecessary inclusions? I would welcome any book suggestions along these lines as well.

  Read the article

• What are some best practices for minimizing code?

  - by CrystalBlue

  While maintaining the sites our development team has created, we have come across include files and plugins that have proven to be very useful to more then one part of our applications. Most of these modules have come with two different files, a normal source file and a min file. Seeing that the performance and speed of a page can be increased by minimizing the size of the file, we're looking into doing that to our pages as well. The problem that we run into is a lot of our normal pages (written in ASP classic) is a mix of HTML, ASP, Javascript, CSS, and include files. We have some pages that have their JS both in include files and in the page, depending on if the function is only really used in that page or if it's used in many other pages. For example, we have a common.js and an ajax.js file, both are used in a lot of pages, but not all of them. As well as having some functions in a page that doesn't really make sense to put into one master page. What I have seen a few other people do online is use one master JS file and place all of their javascript into that, minify it, gzip it, and only use that on their production server. Again, this would be great, but I don't know if that fully works for our purposes. What I'm looking for is some direction to go with on this. I'm in favor of taking all of our JS and putting it in one include file, and just having it included in every page that is hit. However, not every page we have needs every bit of JS. So would it be worth the compilation and minifying of the files into one master file and include it everywhere, or would it be better to minify all other files and still include them on a need-to-use basis?

  Read the article

• New SPC2 benchmark- The 7420 KILLS it !!!

  - by user12620172

  This is pretty sweet. The new SPC2 benchmark came out last week, and the 7420 not only came in 2nd of ALL speed scores, but came in #1 for price per MBPS. Check out this table. The 7420 score of 10,704 makes it really fast, but that's not the best part. The price one would have to pay in order to beat it is ridiculous. You can go see for yourself at http://www.storageperformance.org/results/benchmark_results_spc2The only system on the whole page that beats it was over twice the price per MBPS. Very sweet for Oracle. So let's see, the 7420 is the fastest per $. The 7420 is the cheapest per MBPS. The 7420 has incredible, built-in features, management services, analytics, and protocols. It's extremely stable and as a cluster has no single point of failure. It won the Storage Magazine award for best NAS system this year. So how long will it be before it's the number 1 NAS system in the market? What are the biggest hurdles still stopping the widespread adoption of the ZFSSA? From what I see, it's three things: 1. Administrator's comfort level with older legacy systems. 2. Politics 3. Past issues with Oracle Support.   I see all of these issues crop up regularly. Number 1 just takes time and education. Number 3 takes time with our new, better, and growing support team. many of them came from Oracle and there were growing pains when they went from a straight software-model to having to also support hardware. Number 2 is tricky, but it's the job of the sales teams to break through the internal politics and help their clients see the value in oracle hardware systems. Benchmarks like this will help.

  Read the article

• When does a programmer know when a new job is not right?

  - by Mysterion

  I believe that the interview process is a selling of both parties - what can the employee offer the employer and vice versa. Assuming an individual has been careful in selecting their new employer (via thorough questioning in the interview process), however when they arrive at the job they find the employer has not been honest about certain aspects of the job. Examples of this dishonesty could include: The employee making it clear that technical excellence is an important factor, which is promised by the employer, but is not fully delivered or a good technical structure does not exist. The employee states they want to work on well architected and short (lets say less than 1 yr) long projects, yet when they start they find they are placed on a poorly architected older project. The employee being told of a pair programming environment to get him up to speed on the project, but being left to his own devices/questioning on arrival. The employee is promised a culture that encourages innovation and technical excellence but finds that this is not the case (eg. using technology for knowledge retention is laughed at). I know that a lot of famous developers feel that you make the place you work at. Is it realistic for a new employee with limited experience in the industry (say less than 5 years) to be able to join the company and change attitudes or even challenge the employer on the perceived dishonesty? Should they stay in this job or cut their losses?

  Read the article

• Help w/ iPad 1 performance for tile-based DOM Javascript game

  - by butr0s

  I've made a 2D tile-based game with DOM/Javascript. For each level, the map data is loaded and parsed, then lots of tiles ( elements) are drawn onto a larger "map" element. The map is inside of a container that hides overflow, so I can move the map element around by positioning it absolutely. Works a treat on desktop browsers, and my iPad 2. My problem is that performance is really bad on iPad 1. The performance hit is directly related to all the tile elements in my map, because when I remove or reduce the number of tiles drawn, performance improves. Optimizing my collision detection loop has no effect. My first thought was to batch groups of tiles into containers, then hide/show them based on proximity to the player, however this still causes a huge hiccup when the player moves and a new group of tiles is displayed (offscreen). Actually removing the out-of-sight elements from the DOM, then re-adding them as necessary is no faster. Anyone know of any tips that might speed up DOM performance here? My map is 1920 x 1920 pixels, so as far as I know should be within the WebKit texture limit on iOS 5/iPad. The map is being moved with CSS3 transforms, and I've picked all the other obvious low-hanging fruit.

  Read the article

• ubuntu 12.10 Lenovo b570e, WiFi connected but not working

  - by koogee

  I'm running ubuntu 12.10 liveUSB on a lenovo b570e. It has an atheros wifi card that connects with my home network but I can't browse AT ALL. My network is multiple clients --> router --> isp modem --> Internet I can ping my router (192.168.0.1) but not my isp's modem(192.168.15.1). I have 3 other computers connected to the same router that are working fine (infact i'm posting from one) ping -c 3 google.com unknown host google.com ping -c 3 8.8.8.8 shows 100% packet loss I think its some networking issue. I tried directly connecting it to the router via ethernet cable but same issue. It gets an ip, shows LAN connected but can't browse. If I connect it directly to the isp modem via ethernet cable it starts working fine. Connection Information shows: Interface: 802.11 wifi (wlan0) driver: ath9k security: wpa/wpa2 speed: 150mb/s ip: 192.168.0.106 broadcast: 192.168.0.255 subnet:255.255.255.0 default route: 192.168.0.1 primary dns: 192.168.15.1 i have restarted the router and modem many times. Rebooted the LiveUSB many times.

  Read the article

• Optimising news fetching

  - by aceBox

  I have a web scraper for scraping news from different sources in wp7. My current appraoch for doing this is: load newspapers information from xml file. go to the specified sections and fetch the urls of the news items. go to each url and fetch headline, image, publisher. display using a MVVM architecture of windows phone. The whole thing takes place asynchronously...meaning as soon as url from a section of a newspaper is fetched it is added to the queue, and the second stage consisting of fetching headline, image etc starts... and as soon this is fetched even for one article, it is displayed. Later on as more articles are fetched, they are added on to the list. For the fetching purpose I am using a SmartThreadPool(http://www.codeproject.com/Articles/7933/Smart-Thread-Pool) for windows phone. My problem is that...even for fetching around 80 items (in total) from 9 publications, it is taking more than a minute. How can i speed up the procedure? Note: I have a two stage approach because many times the images are not available with headlines, and are only found in the article.

  Read the article

• TraceTune: Improved Comment View

  - by Bill Graziano

  I wanted an easier way to identify queries I’d already looked at so I could skip them.  I’ve been entering comments for each query as I review it.  These comments typically fall into three categories: a change I made, no easy fix available or something needs to be changed on the client.  TraceTune now highlights any statement with a comment in bold.  If you hover over the statement you’ll see the most recent comment for that statement. This gives me a quick way to see what’s new and identify those queries that still need work.  This is especially helpful when I come back to a server after weeks or months away.  These comments help jar my memory and remind me what I’ve worked on. I made the font slightly smaller in some of the tables.  It’s still readable but I’m able to get more of a SQL statement on the screen.  I also got to re-experience the pain of Internet Explorer, Chrome and FireFox all displaying text (and pop-up text) slightly different. Seeing the comments on a trace has been a big help to me.  I often do a round of tuning and then don’t come back to a server until months later.  Having the comments available helps me get back up to speed quickly.

  Read the article

• Pair Programming, for or against? [on hold]

  - by user1037729

  I believe it has many advantages over individual programming: Pros By pairing senior with relatively junior staff, the more junior can get up to speed with both project and computing experience, and the senior will re-think the problem in order to communicate with the junior, thus re-checking his own thinking (rubber duck principle!). At least 2 people will know about any single piece of work, if one person is away the other can cover, or if some one leaves a project knowledge transfer is easier. Two brains on a complex task is more effective, communication keeps the work free flowing and provides redundancy in decision making. Code is effectively reviewed as its being written, no need for a separate reviewing phase which requires a context switch as someone who has not been working on the piece in question would be required to understand and review the related code. Reviewing code on your own which you haven't written or architected is not fun, hence counter productive. Cons Less bandwith for performing tasks, lets say we have 4 devs, pair programming requires 2 devs per task, so we would be doing 2 tasks concurrently as a posed to 4. I believe this "Con" does not stand up as the pair programmed task would complete sooner and comes with a review built in for free! Ie the pair programming task would be more efficient and thus free up resources earlier. Less flexibility to chop and change tasks as two developers are tied into a task, when flexibility is required this could be a problem.

  Read the article

< Previous Page | 168 169 170 171 172 173 174 175 176 177 178 179  | Next Page >