Search Results

Search found 5367 results on 215 pages for 'devices'.

Page 174/215 | < Previous Page | 170 171 172 173 174 175 176 177 178 179 180 181  | Next Page >

• Why do I get a DegradedArray event with mdadm

  - by azera

  Hello Just so we're clear on what's happening: I bought 4 new sata 2 drives, with the intent of using them in a raid5 all drive are fully recognised by both my bios and my linux box (gentoo) I created a raid5 array, fiddled a bit with it to understand how it works, how to monitor ect At some point, this triggered a degradedarray event, even though the array is brand new. I tried to stopping the array and recreating a new array with the same drive but the new array starts degraded too. here is what I used to create it mdadm --create -l5 -n4 /dev/md/md0-r5 /dev/sdb /dev/sdd /dev/sde /dev/sdf here are the output from my /proc/mdstat and mdadm --detail --scan **mdstat** Personalities : [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md127 : active raid5 sdf[4] sde[2] sdd[1] sdb[0] 4395415488 blocks level 5, 64k chunk, algorithm 2 [4/3] [UUU_] [>....................] recovery = 2.8% (41689732/1465138496) finish=890.3min speed=26645K/sec unused devices: <none> **detail** ARRAY /dev/md/md0-r5 metadata=0.90 spares=1 UUID=453e2833:81f22a74:64188b84:66721085 As such I have a couple questions: does a raid5 array always start in degraded mode at first ? why does sdf have the number 4 between bracket instead of 3, why does it see a spare disk and why is the 4th drive marked with _ instead of U ? (bad configuration ?) How can I recreate the array from scratch, do i have to format each drive on its own before recreating it ? Thanks for any help, I'm not sure about what I should do at the moment

  Read the article

• Problems mounting HPUX LVM+VXFS filesystem on Linux

  - by golimar

  I have a physical disk from a HPUX system that I need to access from a Debian Linux for ia64 system. From the hpux-lvm-tools project I have the tools to access the HPUX LVMs (Linux LVM has a different format) and I also have the freevxfs driver. I know beforehand that the disk has three partitions, and that the biggest one contains LVM volumes, and some of those are VxFS filesystems. I can see the partitions: # cat /proc/partitions major minor #blocks name 8 32 143374744 sdc 8 33 512000 sdc1 8 34 142452736 sdc2 8 35 409600 sdc3 It finds a VG in one of the disk partitions: # ./vgscan_hpux On /dev/sdc2 - vg1328874723 # ./pvdisplay_hpux /dev/sdc2 PV General Information ---------------------- VG Creation Time Fri Feb 10 12:52:03 2012 Physical Volume ID 1766760336 1328874723 Volume Group ID 1766760336 1328874723 Physical Volumes in VG 1766760336 1328874723 VG Actication Mode 0 - LOCAL PE Size 64 MBs Lvol sizes ---------- lvol1 - 8 Extents - 512 MBs lvol2 - 192 Extents - 12288 MBs lvol3 - 16 Extents - 1024 MBs ... lvol21 - 13 Extents - 832 MBs lvol22 - 224 Extents - 14336 MBs lvol23 - 16 Extents - 1024 MBs Then I activate that VG and some new devices appear in my system: # ./pvactivate_hpux /dev/sdc2 VG vg1328874723 Activated succesfully with 23 lvols. # # ll /dev/mapper/ total 0 crw------- 1 root root 10, 59 Nov 26 16:08 control lrwxrwxrwx 1 root root 7 Nov 26 16:38 vg1328874723-lvol1 -> ../dm-0 lrwxrwxrwx 1 root root 7 Nov 26 16:38 vg1328874723-lvol10 -> ../dm-9 ... lrwxrwxrwx 1 root root 7 Nov 26 16:38 vg1328874723-lvol8 -> ../dm-7 lrwxrwxrwx 1 root root 7 Nov 26 16:38 vg1328874723-lvol9 -> ../dm-8 But: # mount /dev/mapper/vg1328874723-lvol18 /mnt/tmp mount: you must specify the filesystem type # mount -t vxfs /dev/mapper/vg1328874723-lvol18 /mnt/tmp mount: wrong fs type, bad option, bad superblock on /dev/mapper/vg1328874723-lvol18, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so # lsmod |grep vxfs freevxfs 23905 0 I also tried to identify the raw data with the file command and it just says 'data': # file -s /dev/mapper/vg1328874723-lvol18 /dev/mapper/vg1328874723-lvol18: symbolic link to `../dm-17' # file -s /dev/dm-17 /dev/dm-17: data # Any clues?

  Read the article

• Windows 7 fails to install

  - by Brian Ortiz

  I'm upgrading from Vista SP1 (which was actually upgraded from XP over a year ago) to Windows 7 RTM (64-bit Ultimate to 64-bit Ultimate). After 4 hours or so, the install fails with the message "This version of Windows could not be installed, Your previous version of Windows has been restored, and you can continue to use it." This error is back at my Vista desktop, there's no error that I could see during install, I just a message indicating that it was reverting everything. I tracked down the error logs and here's the log at I uploaded the error log (from C:\$WINDOWS.~BT\Sources\Panther) and uploaded onto Pastebin. Here is an excerpt: 2009-08-09 02:54:57, Error Number of Enumerated Devices = 21[gle=0x00000103] 2009-08-09 02:54:58, Error Failed to find driver file path. Error=00000002x 2009-08-09 02:54:58, Error Failed to find driver file path. Error=00000002x 2009-08-09 02:54:58, Error Failed to find driver file path. Error=00000002x[gle=0x80092004] 2009-08-09 02:54:58, Error Failed to find driver file path. Error=00000002x[gle=0x80092004] It was suggested that I upgrade to SP2 before upgrading to Vista, but this made no difference. I since uninstalled SP2 since it was creating some problems with a piece of hardware. I know a fresh install is best, but I'm hoping to avoid that because I'd need a new hard drive. Per Reuben's instruction, I found the install's dump and uploaded it here. (266 KB)

  Read the article

• Abysmal transfer speeds on gigabit network

  - by Vegard Larsen

  I am having trouble getting my Gigabit network to work properly between my desktop computer and my Windows Home Server. When copying files to my server (connected through my switch), I am seeing file transfer speeds of below 10MB/s, sometimes even below 1MB/s. The machine configurations are: Desktop Intel Core 2 Quad Q6600 Windows 7 Ultimate x64 2x WD Green 1TB drives in striped RAID 4GB RAM AB9 QuadGT motherboard Realtek RTL8810SC network adapter Windows Home Server AMD Athlon 64 X2 4GB RAM 6x WD Green 1,5TB drives in storage pool Gigabyte GA-MA78GM-S2H motherboard Realtek 8111C network adapter Switch dLink Green DGS-1008D 8-port Both machines report being connected at 1Gbps. The switch lights up with green lights for those two ports, indicating 1Gbps. When connecting the machines through the switch, I am seeing insanely low speeds from WHS to the desktop measured with iperf: 10Kbits/sec (WHS is running iperf -c, desktop is iperf -s). Using iperf the other way (WHS is iperf -s, desktop iperf -c) speeds are also bad (~20Mbits/sec). Connecting the machines directly with a patch cable, I see much higher speeds when connecting from desktop to WHS (~300 Mbits/sec), but still around 10Kbits/sec when connecting from WHS to the desktop. File transfer speeds are also much quicker (both directions). Log from desktop for iperf connection from WHS (through switch): C:\temp>iperf -s ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [248] local 192.168.1.32 port 5001 connected with 192.168.1.20 port 3227 [ ID] Interval Transfer Bandwidth [248] 0.0-18.5 sec 24.0 KBytes 10.6 Kbits/sec Log from desktop for iperf connection to WHS (through switch): C:\temp>iperf -c 192.168.1.20 ------------------------------------------------------------ Client connecting to 192.168.1.20, TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [148] local 192.168.1.32 port 57012 connected with 192.168.1.20 port 5001 [ ID] Interval Transfer Bandwidth [148] 0.0-10.3 sec 28.5 MBytes 23.3 Mbits/sec What is going on here? Unfortunately I don't have any other gigabit-capable devices to try with.

  Read the article

• Unable to connect to cable modem when connected to VPN

  - by Spuas

  the scenario is as follows: First I have a cable modem which gives the internet connection. The network is 192.168.0.0/24 and its IP is 192.168.0.1 Second line, I have a router connected to the cable modem. Its "outside" IP is 192.168.0.12. This router creates network 192.168.123.0/24 and its IP there is 192.168.123.254. My computer is wired to the router with IP 192.168.123.126. At this point I am able to access both devices web interfaces by their IPs on a browser (192.168.123.254 for the router and 192.168.0.1 for the cable modem). The problem I have is when I connect to a VPN from the computer. Then I am connected to a second network 10.0.0.0/24 and I get IP 10.0.0.200 (along with 192.168.123.126). I can connect to the router but then I loose connectivity to the cable modem: I cannot acces it through the browser, neither making a ping to it or a tracert. I have tried to add a new route to the windows routes by typing route ADD 192.168.0.1 MASK 255.255.255.0 192.168.123.254 but I cannot access it anyway... Am I missing something on the route adding? Which is the propper way of doing this? Thanks

  Read the article

• CDROM does not appear on desktop, MACOS 10.5.7

  - by Cheeso

  When I pop a CDROM into the drive of my Macbook Pro, It spins up, I hear it, but no icon appears on the desktop. (I think it's 10.5.7; actually not sure how to verify this on Mac, but I think I saw a 10.5.7 flash by somewhere). In the finder preferences, I have "Show these items on the Desktop" set to show HDs, External Disks, and CDs, DVDs, and ipods. All three of those are checked. I do see the internal HD on the desktop. In Disk utility I can see the CD/DVD hardware. It says "MATSHITA DVD-R UJ-857E...". From Disk Utility I can eject the drive. But in Finder, there is never a CD/DVD listed under "Devices". When I insert a disk, nothing happens, I cannot see it. I also cannot boot from bootable CDROMs by holding C down . Suggestions? I am not very experienced with Mac; I have used Windows for years. EDIT Two updates: I saw this article on support.apple.com, and modified the hostconfig appropriately. It did not have the AUTODISKMOUNT entry, so I added one, rebooted. Same behavior. It does not see the CDROM in Finder, does not mount it on desktop. I put an old manufactured CDROM into the drive, and voila! it showed up on the desktop. The CD that does not appear is a GNome Partition Editor Live CD, which I guess is based on debian. That CD boots in other (non-Mac) PCs. I want to use this to adjust the Bootcamp partition. Suggestions?

  Read the article

• DNS issue for internal website routing internet connection from remote location

  - by Michael Paul

  I have an issue that I could use some help with. Our company has a main location and a remote location. Previously, the remote location was connected to the main location through an internet connection VPN tunnel. The connection was pitifully slow at 1.5Mbps, so we upgraded it with a 75Mbps direct link. That meant the remote location lost it's internet access, so we routed their access through the main office internet connection. Everything works perfect except for one thing. The website we host is not accessible from the remote location unless the IP address is used. If I do NSLOOKUP on our website address from a machine connected to the main location network, it resolves correctly to the inside IP address. However, if I do the same from a remote location machine, it resolves to the website's outside IP address. Our internal DNS server(s) have a pointer and CNAME records set up, and everything was working perfectly before the connection was upgraded. In addition, the remote location has a domain controller, DNS server and DHCP server to service these requests at the remote location and prevent these requests from getting routed back and forth over the link. So I think was it happening is that for some reason the DNS server at the remote location is not resolving our website name correctly and passing the requests on to the routers, which then push the request out to the internet DNS system. That resolves the name to our external IP. This is purely a DNS issue, everything else works just fine. I am just stumped on this one. Any ideas on how to fix this? Edit: I forgot to mention that at the remote side of the link is a Cisco ASA-5505 and at the main office there is a Cisco ASA-5510. The link is connected between these 2 devices and the routing is handled in the 5510. Thanks, Michael

  Read the article

• Does Guest WiFi on an Access Point make any sense?

  - by uos??

  I have a Belkin WiFi Router which offers a feature of a secondary Guest Access WiFi network. Of course, the idea is that the Guest network doesn't have access to the computers/devices on the main network. I also have a Comcast-issues Cable Modem/Router device with mutliple wired ports, but no WiFi-capabilities. I prefer to only run one router/DHCP/NAT instead of both the Comcast Router and the Belkin Router, so I can disable the Routing functions of the Belkin and allow the Comcast Router to But if I disable the Routing functions of the Belkin device, the Guest WiFi network is still available. Is this configuration just as secure as when the Belkin acts as a Router? I guess the question comes down to this: Do Guest WiFi's provide security by 1) only allowing requests to IPs found in-front of the device, or do they work by 2) disallowing requests to IPs on the same subnet? 1) Would mean that Guest WiFi on an access point provides no benefit 2) Would mean that the Guest WiFi functionality can work even if the device is just an access point. Or maybe something else entirely?

  Read the article

• I can't connect to my network, except in safe mode

  - by eidylon

  My laptop cannot connect to my network all of a sudden except in safe mode. When it boots, it will show the networks available in the tray popup, but if I click connect on any, it says "Unable to connect" and the troubleshooter is useless. Shortly thereafter all the networks disappear. I have tried removing IPv6 support as I have seen that cause problems. No joy. I've also tried removing the wireless network adapter in Device Manager and reinstalling it, also no joy. I've also tried attaching a USB wireless adapter, and it has the same problem. If I boot in safe mode, then it has no problems at all. Three other devices in the house connect fine, so I am pretty sure it is nothing to do with the router. Any ideas what to check next? I am running Win7 Ultimate on a 2GHz Quadcore with 8GB RAM with a Broadcom 802.11n wireless card. EDIT: RE wired connections: What is very weird is that if i plug in a wired connection, then not only does it connect via the wired connection, but the wireLESS also starts working perfectly. And a soon as I unplug the wire, then the wireLESS stops working again! So it seems the wireless is right now working only in safe-mode, or when a wired connection is also plugged in.

  Read the article

• MicroSD card isn't detected by computer, apparently usable only with phone

  - by paulcjoubert

  I have a 4GB MicroSD card that apparently only works (in the sense that the device detects and can read and write from and to the card) with my old Nokia XpressMusic 5800 phone. I have taken pictures and recorded voice notes that were saved on the card. These are accessible after the card has been removed, which tells me that the problem isn't with the card. The card could also not be locked to the phone as it would at least be detected by a computer and it would be able to write raw data to it with dd, such as /dev/zero. Also, the card is not the Nokia card that came with the phone and I have done nothing that would have caused it to be locked. (I could not find anything on Nokia's website that helps, but then again... my search was not THAT thorough.) The card works on no other device that I have tried so far. I have tried it in my Canon camera (through an adapter), but it refuses to even boot with the card inserted. My card reader (via USB cable and hub) is detected as /dev/sdx with or without the card inserted. When trying to access the card I get an "No medium found". dmesg does not report any change at all when inserting and removing the card. I would obviously like to use my card on other devices - the phone is quite old - and even a likely explanation would help. Thankyou in advance! EDIT 1: I can use the card by connecting the phone to my computer, but this is impractical and would not allow me to use the card in any other device. EDIT 2: The data on the card is not important to me at all.

  Read the article

• What does this mean: "SATP VMW_SATP_LOCAL does not support device configuration"?

  - by Jason Tan

  Can anyone tell me what this means in ESXi 5.1?: SATP VMW_SATP_LOCAL does not support device configuration I've googled it and I get a lot of results, but as yet all the pages that contain the string are discussing other matters. The storage array is a HDS HUS-VM and the hosts are HP b460c G8 blades with flex fabric and flex fabric VCs which I am in the process of commissioning and would like to get it started on the right foot - i.e. error and warning free! naa.600508b1001c56ee3d70da65f071da23 Device Display Name: HP Serial Attached SCSI Disk (naa.600508b1001c56ee3d70da65f071da23) Storage Array Type: VMW_SATP_LOCAL Storage Array Type Device Config: SATP VMW_SATP_LOCAL does not support device configuration. Path Selection Policy: VMW_PSP_FIXED Path Selection Policy Device Config: {preferred=vmhba0:C0:T0:L1;current=vmhba0:C0:T0:L1} Path Selection Policy Device Custom Config: Working Paths: vmhba0:C0:T0:L1 Is Local SAS Device: true Is Boot USB Device: false This is the same LUN: ~ # esxcli storage core device list -d naa.60060e80132757005020275700000016 naa.60060e80132757005020275700000016 Display Name: HITACHI Fibre Channel Disk (naa.60060e80132757005020275700000016) Has Settable Display Name: true Size: 204800 Device Type: Direct-Access Multipath Plugin: NMP Devfs Path: /vmfs/devices/disks/naa.60060e80132757005020275700000016 Vendor: HITACHI Model: OPEN-V Revision: 5001 SCSI Level: 2 Is Pseudo: false Status: degraded Is RDM Capable: true Is Local: false Is Removable: false Is SSD: false Is Offline: false Is Perennially Reserved: false Queue Full Sample Size: 0 Queue Full Threshold: 0 Thin Provisioning Status: unknown Attached Filters: VAAI_FILTER VAAI Status: supported Other UIDs: vml.020001000060060e801327570050202757000000164f50454e2d56 Is Local SAS Device: false Is Boot USB Device: false ~ #

  Read the article

• Google Chrome doesn't want to access Facebook

  - by Pieter van Niekerk

  I have been experiencing a bit of a problem with Chrome over the last couple of days where it doesn't want to access Facebook. When I open Chrome it works fine for a while and then if I were to refresh the page it would give me the Chrome 'This webpage is not available' message. This webpage is not available Google Chrome could not load the webpage because www.facebook.com took too long to respond. The website may be down, or you may be experiencing issues with your Internet connection. Here are some suggestions: Reload this webpage later. Check your Internet connection. Restart any router, modem, or other network devices you may be using. Add Google Chrome as a permitted program in your firewall's or antivirus software's settings. If it is already a permitted program, try deleting it from the list of permitted programs and adding it again. If you use a proxy server, check your proxy settings or contact your network administrator to make sure the proxy server is working. If you don't believe you should be using a proxy server, adjust your proxy settings: Go to the wrench menu Options Under the Hood Change proxy settings... LAN Settings and deselect the "Use a proxy server for your LAN" checkbox. This problem only persists when using the proxy and doesn't occur at all when not on the proxy. I have also tried different browsers (IE9 and Firefox 9.01) but it doesn't occur in any of them. This problem goes away for a while when I restart Chrome, only to happen again a couple of minutes later. I have tried deleting the cookies for Facebook without restarting Chrome, but to no avail. I am using Windows7 with Chrome 17

  Read the article

• Cisco ASA with CSC module bypassing

  - by Shial

  We recently upgraded from a Watchguard X5500e Peak firewall appliance to a Cisco 5500 ASA with the CSC module. The ASA is running the 8.2 software and the CSC is on the 6.3.1172 software. We've finally gotten everything stabilized after a few weeks of pulling hairs and gnashing of teeth and now its down to trying to setup a few items that were lower on the priority list. With the watchguard we were able to go with the browser to an internal webpage and authenticate against the firewall to allow us to bypass the filters. Useful when a classroom here needs access to streaming media or an executive needs us to download a video. I'm trying to setup something similar but I'm fairly inexperienced with the Cisco devices like this ASA so I'm not sure if its treated as a VPN connection or some kind of ACL. Ideally we would want to setup more than one to limit exposure rather than one thats wide open when used. I did a search and couldn't find anything related to thing in the other questions asked here and I have had no luck googgling it either.

  Read the article

• Mac Mini's internet very slow, every other device fine (PC, iPhone, Xbox 360)

  - by alex

  I recently haven't used my Mac Mini for about 5 days (however it was left on). I seem to be able to connect and get great download / upload speeds through my PC, Xbox 360, iPhone and parents' laptop. However, my Mac Mini is very slow. OS X's Mail.app is downloading mail at 0.4kbps and then dropping to 0. Skype file transfers are doing the same. Browsing the net is a terrible experience. It is taking 30 seconds or more to download basic pages. All of my devices connect wirelessly to a Netgear router / modem. I have tried giving the Mac Mini a manual IP, and renew DHCP lease, as well as flush DNS in Terminal. I have also rebooted the router / modem twice, and the Mac Mini twice. Do you know what could be causing this? Thanks Update This is very weird. It is also very slow accessing localhost (setup through MAMP) and also slow to access the Netgear router config pages.

  Read the article

• RRAS with DHCP when the IP pool is on a different subnet

  - by John B

  I run a small business network and the last couple of days I have been setting up some equipment to add VPN capabilities to our network. I've got the following set up: Windows 2008 R2 with RRAS - 172.22.200.50 Cisco RV082 router - 172.22.100.1 / 172.22.200.1 The Cisco router only support DHCP on a single class C network; 172.22.100.0/24. On the Cisco router I have set up an additional subnet; 172.22.200.0/24. The DHCP range is 172.22.100.200-254 When a PPTP connection comes in to the router, it is forwarded to my RRAS at 172.22.200.50. If I configure RRAS to assign IPs from a static pool on the 172.22.200.0/24 subnet everything works fine except the DNS suffix / search domain. However, if I set RRAS to use DHCP I am no longer able to contact any devices on the network. The IP I receive is on a different subnet (172.22.100.0/24). Is it possible to still use DHCP as the method of ip assignment in RRAS, even when the IP adresses assigned are in a different subnet? If yes, what piece of configuration am I missing to fix the VPN connection issues mentioned in the paragraph above. The reason I want RRAS with DHCP to work is because from what I have understood, this is the "only" way to hand out a DNS suffix to VPN clients. Any help on this matter is greatly appreciated!

  Read the article

• Fixed and dynamic IPs in ISC DHPD lead to double lease

  - by GorillaPatch

  I would like to have a small dynamic adress part and the most clients are assigned a fixed IP adress. My dhcpd.conf looks like this: use-host-decl-names on; authoritative; allow client-updates; ddns-updates on; # Einstellungen fuer DHCP leases default-lease-time 3600; max-lease-time 86400; lease-file-name "/var/lib/dhcpd/dhcpd.leases"; subnet 192.168.11.0 netmask 255.255.255.0 { ddns-updates on; pool { # IP range which will be assigned statically range 192.168.11.1 192.168.11.240; deny all clients; } pool { # small dynamic range range 192.168.11.241 192.168.11.254; # used for temporary devices } } group { host pc1 { hardware ethernet xx:xx:xx:xx:xx:xx; fixed-address 192.168.11.11; } } The motivation for the pool declaration with deny all hosts comes from the ISC DHCPD homepage http://www.isc.org/files/auth.html This will allow hosts to be first added to the network, where they will receive a temporary IP from the 241-254 adress range and then later write an explicit host declaration. Upon next connect it will receive the right configuration. The problem is that I am getting error messages that 192.168.11.13 has a dynamic and a static lease. I am a bit confused as I expected the pool declaration with deny all clients would not count as dynamic. Dynamic and static leases present for 192.168.11.13. Remove host declaration pc1 or remove 192.168.11.13 from the dynamic address pool for 192.168.11.0/24 Is there a way to have the DHCP server send an DHCPNA to clients if they have a host statement and retain this dynamic range?

  Read the article

• Managing multiple IMAP accounts in Thunderbird

  - by baritoneuk

  I've been using Thunderbird for years without issues with 20+ pop3 accounts. I'm moving over to imap which will enable me to keep copies of the emails locally and on the server whilst keeping everthing synchronised. However I'm looking for the best way to manage multiple imap accounts on Thunderbird. Currently I have a filter that copies all the emails into a central inbox and into seperate local folders. The reason for this is I go through my inbox daily and delete all emails that don't require any action. I move any emails that require action to my "action" imap account folder. This way I can syncronise all the emails that require action across multiple computers (and mobile devices). This technique is my implemantion of the GTD or Getting things Done philosophy. I also copy over each email into seperate local folders. The reason I do this is just in case any emails on the imap accounts get deleted, or something drastic happens on the server which means I lose all the emails. My business partner has access to some of these emails and still uses pop3 (with "leave copy on server" checked), but I know sometimes Thunderbird can still delete emails off the server sometimes. The problem with the above is that thunderbird gives me the dreaded error dialogue saying that the emails cannot be filtered due to another process. I find the folder list in Thunderbird hard to manage. Here is a screenshot of part of my folder list- as you can see it's a bit of a complicated list and not easy to manage: What would be the best way of me managing multiple imap accounts whilst allowing me to have copies put in a central folder and emails in local folders? It would be useful if people think this is necessary, as perhaps there is a betterway? How do people manage multiple imap accounts in a way that allows them to keep on top of actionable emails? I'd be interested in how others manage this. I've never used the Thunderbird-based client "Postbox", does this handle multiple imaps better?

  Read the article

• Dell XPS 17 Laptop USB SS Ports don't work until machine rebooted

  - by Matt

  I have a new Dell XPS 17 laptop and have an issue that the two USB SS ports on the rear of the machine are not recognising anything when I start-up. Have tried mouse, keyboard, headset, USB display. If I plug a USB hub in the power light on the hub lights (presume this is hard-wired) but a mouse plugged into the hub does not light up. If I restart the pc the ports work fine. Also the other two USB ports work fine all the time. I have switched off the power saving setting on the device manager (Power managementAllow the computer to turn off this device to save power) and also in the advanced power settings (USB Settings USB Selective suspend setting:disabled) I have also disabled USB powershare in the BIOS (not sure what this actually does!) This is becoming very annoying having to restart the machine every day before I can start work Running Win 7 Pro x64 EDIT: I have found that setting USB Emulation to Disabled has helped the devices to be recognised during start up but they keep dropping out completely when in use EDIT 2: I contacted Dell about this issue who told me to update the BIOS driver, when I asked if I should downgrade from the factory installed A13 to the A12 posted on the dell website they said no. However there is now an A14 available on the website has anyone tried this?

  Read the article

• Troubleshooting a Windows 7 PC that wouldn't sleep

  - by NPE

  I have a new Windows 7 PC that wouldn't sleep (not just automatically, but also when specifically told to). The screen goes black momentarily, but within two seconds the machine comes back as if nothing has happened. I tried powercfg energy. This produces some errors quoted at the bottom of this post, plus some warnings about timer resolution. There are no USB devices connected other than wireless keyboard + mouse (Logitech MK250); I tried unplugging them to no effect. The motherboard is Asus P7P55D-E. powercfg lastwake says "Wake History Count - 0", which I take to mean that it never actually went to sleep. I dual boot into Ubuntu, and was having exactly the same problem on the Linux side. That turned out to do with USB 3.0, which I've now disabled in the BIOS. This has solved the problem on the Ubuntu side of things, but made no difference to Windows 7. Any suggestions? Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name Generic USB Hub Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_8087&PID_0020 Port Path 1 USB Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name USB Root Hub Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_8086&PID_3B34 Port Path USB Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name USB Composite Device Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_046D&PID_C52E Port Path 1,8

  Read the article

• CentOS iscsi initiator has session but there is no block device

  - by jcalfee314

  I have installed the scsi-target-utils package on CentOS and I used it to perform a discovery. The discovery did give me an active session. I restarted the iscsi service but I do not see any new devices (fdisk -l). I see in /var/log/messages that my connection is operational now. I'm not sure how to debug this further. Can someone direct me into fixing this? discovery: iscsiadm -m discovery -t sendtargets -p 192.168.0.155 returns: 192.168.0.155:3260,-1 iqn.2009-02.com.twinstrata:cloudarray:sn-1d07c1b62d4ec8f3 Just to verify it actually worked: iscsiadm -m session returns tcp: [1] 192.168.0.155:3260,1 iqn.2009-02.com.twinstrata:cloudarray:sn-1d07c1b62d4ec8f3 restarting as the directions say to do: service iscsi restart output written to /var/log/message Stopping iscsi: Sep 20 12:14:22 localhost kernel: connection1:0: detected conn error (1020) [ OK ] Starting iscsi: Sep 20 12:14:22 localhost kernel: scsi1 : iSCSI Initiator over TCP/IP Sep 20 12:14:22 localhost iscsid: Connection1:0 to [target: iqn.2009-02.com.twinstrata:cloudarray:sn-1d07c1b62d4ec8f3, portal: 192.168.0.155,3260] through [iface: default] is shutdown. Sep 20 12:14:22 localhost iscsid: Could not set session2 priority. READ/WRITE throughout and latency could be affected. [ OK ] [root@db iscsi]# Sep 20 12:14:23 localhost iscsid: Connection2:0 to [target: iqn.2009-02.com.twinstrata:cloudarray:sn-1d07c1b62d4ec8f3, portal: 192.168.0.155,3260] through [iface: default] is operational now Ran a login command: iscsiadm -m node -T iqn.2009-02.com.twinstrata:cloudarray:sn-1d07c1b62d4ec8f3 -p 192.168.0.155 -l No errors, no logging occurred. Next I compared the output from "fdisk -l|egrep dev" both with the iscsi session and without. There is no difference. I suppose I could just look in /etc/mtab. Any ideas on how I can get an iscsi device?

  Read the article

• Troubleshooting loss of network connectivity in Windows 2003 - What else to check?

  - by Benny

  We are facing a weird problem in our data center. Our Backup server (running EMC Networker) loses network connection every alternate day around 3:00 AM (Backup schedule starts at midnight). After 2 hours of outage, the network connectivity recovers automatically and back to normal. What we observed: It is unlikely to be network issue, since it is directly connected to server farm switch (layer 2 connection without any intermediate hops). Further, the server is connected to two different switches for Load balancing using Broadcomm Teaming. a) If it were a switch related issue it is unlikely that both the network ports go down, since they are connected to different switch. b) A possibility Vlan wide issue is also ruled out since other devices in the same Vlan are fine. c) Switch interface status is always up. But there are lot of packet drops during the outage period - Can be attributed to high interface utilization of the backup server (near 100%) d) Connectivity is restored without any change on network. Next suspect is resource utilization on Windows server. Both CPU and Memory have rarely exceeded 80%, but NIC card utilization is alarmingly high (near 100%) Not really sure how to investigate this?

  Read the article

• ios7 loops on the "trust this computer" dialog

  - by gcb

  trying to transfer files to the work ipad via my debian7 box. When i plug it on the computer usb port, it shows the dialog about trusting this computer, and the computer shows a gnome alert about the ipad being locked and that i should unlock it and try again. i press "trust" on the ipad and try again on gnome. and it starts again. over and over. endlessly. there are dozen threads about this on apple support forums. no solution. just dozens of "me too" flags. e.g. https://discussions.apple.com/message/23082859#23082859 (44 me-too, 2k views) here is the log/messages i get Oct 23 21:17:39 dotmatrix kernel: [ 1928.517766] usb 2-1.7: USB disconnect, device number 16 Oct 23 21:17:39 dotmatrix kernel: [ 1928.715441] usb 2-1.7: new high-speed USB device number 17 using ehci_hcd Oct 23 21:17:40 dotmatrix kernel: [ 1928.811031] usb 2-1.7: New USB device found, idVendor=05ac, idProduct=12ab Oct 23 21:17:40 dotmatrix kernel: [ 1928.811036] usb 2-1.7: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Oct 23 21:17:40 dotmatrix kernel: [ 1928.811039] usb 2-1.7: Product: iPad Oct 23 21:17:40 dotmatrix kernel: [ 1928.811041] usb 2-1.7: Manufacturer: Apple Inc. Oct 23 21:17:40 dotmatrix kernel: [ 1928.811043] usb 2-1.7: SerialNumber: fec5e0f6a6fa18a936de3c53af661051d290275e Oct 23 21:17:40 dotmatrix mtp-probe: checking bus 2, device 17: "/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.7" Oct 23 21:17:40 dotmatrix mtp-probe: bus: 2, device: 17 was not an MTP device Oct 23 21:17:43 dotmatrix kernel: [ 1932.346505] usb 2-1.7: USB disconnect, device number 17 If i never press the trust dialog it will stay there until i remove the cable. but the logs shows that it gave up 3sec after the cable was connected.

  Read the article

• How do I Install Intermediate Certificates (in AWS)?

  - by getmizanur

  I have installed private key (pem encoded) and public key certificate (pem encoded) on Amazon Load Balancer. However, when I check the SSL with site test tool, I get the following error: Error while checking the SSL Certificate!! Unable to get the local issuer of the certificate. The issuer of a locally looked up certificate could not be found. Normally this indicates that not all intermediate certificates are installed on the server. I converted crt file to pem using these commands from this tutorial: openssl x509 -in input.crt -out input.der -outform DER openssl x509 -in input.der -inform DER -out output.pem -outform PEM During setup of Amazon Load Balancer, the only option I left out was certificate chain. (pem encoded) However, this was optional. Could this be cause of my issue? And if so; How do I create certificate chain? UPDATE If you make request to VeriSign they will give you a certificate chain. This chain includes public crt, intermediate crt and root crt. Make sure to remove the public crt from your certificate chain (which is the top most certificate) before adding it to your certification chain box of your Amazon Load Balancer. If you are making HTTPS requests from an Android app, then above instruction may not work for older Android OS such as 2.1 and 2.2. To make it work on older Android OS: go here click on "retail ssl" tab and then click on "secure site" "CA Bundle for Apache Server" copy and past these intermediate certs into certificate chain box. just incase if you have not found it here is the direct link. If you are using geo trust certificates then the solution is much the same for Android devices, however, you need to copy and paste their intermediate certs for Android.

  Read the article

• Merging cuesheet chapter halves into single track for an audiobook

  - by TheSavo

  I have an audiobook that I have ripped and I need some help constructing chapters. I have already made some cue sheets TITLE "Bookname" PERFORMER "the Author" FILE "File1.FLAC" wave ; 23971906.667 milliseconds TRACK 01 AUDIO TITLE "_Intro" INDEX 01 00:00:00 TRACK 02 AUDIO TITLE "CH 01" INDEX 01 24:15:50 TRACK 03 AUDIO TITLE "CH 02" INDEX 01 66:21:00 TRACK 04 AUDIO TITLE "CH 03" INDEX 01 87:05:00 The audio book is in two files. The chapter at the end of the first file is continued in the second file. However, the second file restates: The publisher Book Title List item Blah blah blah I would like to merge the two 'halves' of the chapter in one seamless track. The only way I can think to do this would be be: Bulk cut down the tracks. Drop the junk info into junk track Continue the track listings as normal Take the two "halves" of the target chapter and build a separate cue sheet for it. I know there has to be an easier way. I am ok with making the 'junk' info a 'gap' or something. These are are FLAC files that will be converted to MP3 for my phone and other potable devices. I have read the primers on cue sheets, but I am just not getting it.

  Read the article

• Windows Server 2008 backup VHD's - is it possible to mount/open in Windows 7?

  - by Simon

  Hi All, Is it possible to mount the VHD files created by the Windows Server 2008 backup utility onto a Windows 7 (release) client? Following an array failure I was very worried that there was a problem with both the backup sets on different USB drives as attaching the VHD to a Win 7 box did not show the expected structure (instead they behaved like unformatted disk space). Subsequently, I've attached the backup drive to a 2008r2 machine that I'd intended to be the replacement and the backup set can be browsed without issue (seemingly). When the new disks arrive I'll go through the recovery process and see where we are, but it looks promising so far. Is it simply the case that you can't take server created VHD's and mount them on desktop machines? (Rather than hyper-ventilating at the thought of years of lost photos and email, I'm now just mildly curious) Edit:One thing that has confused things is that the backup utility on Win7 is more restrictive about restoring from external devices than the equivilent on 2008r2. With r2, I can restore files 'from another server' and browse to external storage. Win7 only allows the back to be located on a network share. Once my box of new disks arrive and I've got something to restore onto, I'll move the smaller of the backup VHDs onto network storage reachable by Win7 and see if the VHD is readable. I haven't read up on the VHD process used by the backup app - I'm assuming it's a base VHD and differencing files used for incremental backups and that the restore app understands this. Finally: In retrospect the question should have been, 'can I restore a 2008r2 backup set via a Win 7 client' Thanks

  Read the article

< Previous Page | 170 171 172 173 174 175 176 177 178 179 180 181  | Next Page >