Search Results

Search found 18961 results on 759 pages for 'tp link'.

Page 174/759 | < Previous Page | 170 171 172 173 174 175 176 177 178 179 180 181  | Next Page >

• wireless detected but Can't connect to network, Wifi card intel pro wireless N100 BGN

  - by Alexandre777

  Thanks in advance, I installed Linux Mint kernel 3.0.0-12 x64 ,wireless is detected and I configure it in network manager but can't coonect, there are the results of command line: $ iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off $ sudo lshw -C network** *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:51:c9:d6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:48 memory:d7400000-d7401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: c0 serial: 48:5b:39:99:8f:16 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.2 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:51 memory:d3800000-d383ffff ioport:8000(size=128 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Thank you.

  Read the article

• Cannot enable wireless on an Intel WifiLink 1000 on an Lenovo Ideapad z570

  - by Brij

  I am using the ubuntu 11.10 on lenovo ideapad z570. My wireless internet is not working. I have ensure that wireless switch is on. Windows 7, wireless works great.However ubuntu 11.10 is not allowing me to enable wireless connection. I have run the following command and here is the status. sudo lshw -class network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:1c:a4:a4 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:42 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: f0:de:f1:64:b6:62 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff Here is rfkill list all output: rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no Note : Windows 7, wireless card property shows that Intel WifiLink 1000 BGN. Could someone help me to fix this issue.

  Read the article

• Unit testing internal methods in a strongly named assembly/project

  - by Rohit Gupta

  If you need create Unit tests for internal methods within a assembly in Visual Studio 2005 or greater, then we need to add an entry in the AssemblyInfo.cs file of the assembly for which you are creating the units tests for. For e.g. if you need to create tests for a assembly named FincadFunctions.dll & this assembly contains internal/friend methods within which need to write unit tests for then we add a entry in the FincadFunctions.dll’s AssemblyInfo.cs file like so : 1: [assembly: System.Runtime.CompilerServices.InternalsVisibleTo("FincadFunctionsTests")] where FincadFunctionsTests is the name of the Unit Test project which contains the Unit Tests. However if the FincadFunctions.dll is a strongly named assembly then you will the following error when compiling the FincadFunctions.dll assembly :      Friend assembly reference “FincadFunctionsTests” is invalid. Strong-name assemblies must specify a public key in their InternalsVisibleTo declarations. Thus to add a public key token to InternalsVisibleTo Declarations do the following: You need the .snk file that was used to strong-name the FincadFunctions.dll assembly. You can extract the public key from this .snk with the sn.exe tool from the .NET SDK. First we extract just the public key from the key pair (.snk) file into another .snk file. sn -p test.snk test.pub Then we ask for the value of that public key (note we need the long hex key not the short public key token): sn -tp test.pub We end up getting a super LONG string of hex, but that's just what we want, the public key value of this key pair. We add it to the strongly named project "FincadFunctions.dll" that we want to expose our internals from. Before what looked like: 1: [assembly: System.Runtime.CompilerServices.InternalsVisibleTo("FincadFunctionsTests")] Now looks like. 1: [assembly: System.Runtime.CompilerServices.InternalsVisibleTo("FincadFunctionsTests, 2: PublicKey=002400000480000094000000060200000024000052534131000400000100010011fdf2e48bb")] And we're done. hope this helps

  Read the article

• jQuery - Opening links within tabs

  - by rwbutler

  Hi all, At present I have some jQuery tabs and these tabs contain links. Unfortunately on following one of the links, the new page opens as if you were following any normal link i.e. not within the tab which is want I would want to happen. Have tried following this section but to no avail: http://jqueryui.com/demos/tabs/#...open_links_in_the_current_tab_instead_of_leaving_the_page Any ideas what might be going wrong here? Many thanks in advance! <html> <head> <script src="jquery-1.4.2.min.js"></script> <script src="jquery-ui-1.8rc3.custom.min.js"></script> <link href="redmond/jquery-ui-1.8rc3.custom.css" rel="stylesheet" type="text/css"></link> <script type="text/javascript"> $(function() { $("#tabs").tabs({ load: function(event, ui) { $("a", ui.panel).click(function() { $(ui.panel).load(this.href); return false; }); } }); }); </script> </head> <body> <div id="tabs"> <ul> <li><a href="#tabs-1">Nunc tincidunt</a></li> <li><a href="#tabs-2">Proin dolor</a></li> <li><a href="#tabs-3">Aenean lacinia</a></li> </ul> <div id="tabs-1"> <a href="page.html">link</a> <p>Proin elit arcu, rutrum commodo, vehicula tempus, commodo a, risus. Curabitur nec arcu. Donec sollicitudin mi sit amet mauris. Nam elementum quam ullamcorper ante. Etiam aliquet massa et lorem. Mauris dapibus lacus auctor risus. Aenean tempor ullamcorper leo. Vivamus sed magna quis ligula eleifend adipiscing. Duis orci. Aliquam sodales tortor vitae ipsum. Aliquam nulla. Duis aliquam molestie erat. Ut et mauris vel pede varius sollicitudin. Sed ut dolor nec orci tincidunt interdum. Phasellus ipsum. Nunc tristique tempus lectus.</p> </div> <div id="tabs-2"> <a href="page.html">link</a> <p>Morbi tincidunt, dui sit amet facilisis feugiat, odio metus gravida ante, ut pharetra massa metus id nunc. Duis scelerisque molestie turpis. Sed fringilla, massa eget luctus malesuada, metus eros molestie lectus, ut tempus eros massa ut dolor. Aenean aliquet fringilla sem. Suspendisse sed ligula in ligula suscipit aliquam. Praesent in eros vestibulum mi adipiscing adipiscing. Morbi facilisis. Curabitur ornare consequat nunc. Aenean vel metus. Ut posuere viverra nulla. Aliquam erat volutpat. Pellentesque convallis. Maecenas feugiat, tellus pellentesque pretium posuere, felis lorem euismod felis, eu ornare leo nisi vel felis. Mauris consectetur tortor et purus.</p> </div> <div id="tabs-3"> <p>Mauris eleifend est et turpis. Duis id erat. Suspendisse potenti. Aliquam vulputate, pede vel vehicula accumsan, mi neque rutrum erat, eu congue orci lorem eget lorem. Vestibulum non ante. Class aptent taciti sociosqu ad litora torquent per conubia nostra, per inceptos himenaeos. Fusce sodales. Quisque eu urna vel enim commodo pellentesque. Praesent eu risus hendrerit ligula tempus pretium. Curabitur lorem enim, pretium nec, feugiat nec, luctus a, lacus.</p> <p>Duis cursus. Maecenas ligula eros, blandit nec, pharetra at, semper at, magna. Nullam ac lacus. Nulla facilisi. Praesent viverra justo vitae neque. Praesent blandit adipiscing velit. Suspendisse potenti. Donec mattis, pede vel pharetra blandit, magna ligula faucibus eros, id euismod lacus dolor eget odio. Nam scelerisque. Donec non libero sed nulla mattis commodo. Ut sagittis. Donec nisi lectus, feugiat porttitor, tempor ac, tempor vitae, pede. Aenean vehicula velit eu tellus interdum rutrum. Maecenas commodo. Pellentesque nec elit. Fusce in lacus. Vivamus a libero vitae lectus hendrerit hendrerit.</p> </div> </div> </body> </html>

  Read the article

• Ubuntu Server 13.10 can't mount hard drive that is on my router

  - by Keytachi626

  So I am working currently with my Ubuntu server which I have it on my laptop at the moment so I can test out how to work with the server OS. I have it up and running with samba, openSSH, webmin, and plexmedia server. My problem is that I can't seem to get the server to get to the router hard drive. I have a TP-link wdr3500. The format of the hard drive is a FAT32. What I've tried: install cifs. sudo vi /etc/fstab Type out \\ \tplinklogin.net\volume1 \mnt\media cifs guest 0 0 I have also tried out \\\192.168.0.1\volume1 \mnt\media cifs guest 0 0 But then when I go to terminal and do sudo mount -a, I usually get a error saying wrong fs type, bad option, bad superblock on //ipaddress/dns/volume1 , missing codepage or helper program, or other error. But in dmesg it will say unable to determine destination address. So am I doing something wrong here? I can't install the hard drive on to my laptop since my family is constantly using it to transfer data back and forth on it and they get mad at me if I just take it away.

  Read the article

• Incorrectly formatted html inconsistencies between DOM and what's displayed in firefox plugin

  - by deadalnix

  I'm currently developing a firefox plugin. This plugin has to handle very crappy website that is really incorrectly formatted. I cannot modify these websites, so I have to handle them. I reduced the bug I'm facing to a short sample of html (if this appellation is appropriate for an horror like this) : <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html> <head> <title>Some title.</title> <!-- Oh fuck yes ! --> <div style="visability:hidden;"> <a href="//example.com"> </a> </div> <!-- If meta are reduced, then the bug disapears ! --> <meta name="description" content="Homepage of Company.com, Company's corporate Web site" /> <meta name="keywords" content="Company, Company & Co., Inc., blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla" /> <meta http-equiv="Content-Language" content="en-US" /> <meta http-equiv="content-type" content="text/html; charset=utf-8"/> </head> <body class="homePage"> <div class="globalWrapper"><a href="/page.html">My gorgeous link !</a></div> </body> </html> When opening the webpage, « My gorgeous link ! » if displayed and clickable. However, when I'm exploring the DOM with Javascript into my plugin, everything behaves (DOM exploration and innerHTML property) like the code was this one : <html> <head> <title>Some title.</title> <!-- Oh fuck yes ! --> </head><body><div style="visability:hidden;"> <a href="//example.com"> </a> </div> <!-- If meta are reduced, then the bug disapears ! --> <meta name="description" content="Homepage of Company.com, Company's corporate Web site"> <meta name="keywords" content="Company, Company &amp; Co., Inc., blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla, blablabla"> <meta http-equiv="Content-Language" content="en-US"> </body> </html> So, when exploring the DOM within the plugin, the document is somehow fixed by firefox. But this fixed DOM is inconsistent with what is in the webpage. Thus, my plugin doesn't behave as expected. I'm really puzzled with that issue. The problem exists in both firefox 3.6 and firefox 4 (didn't tested firefox 5 yet). For example, reducing the meta, will fix the issue. Where does this discrepancy come from ? How can I handle it ? EDIT: With the answer I get, I think I should be a little more precise. I do know what firefow is doing when modifying the webpage in the second code snippet. The problem is the following one : « In the fixed DOM that I get into my plugin, the gorgeous link doesn't appear anywhere, but this link is actually visible on the webpage, and works. So the DOM I'm manipulating, and the DOM in the webpage are different - they are fixed in a different manner. » . So where does the difference come in the fixing behaviour, and how can I handle that, or, in other terms, how can I be aware, in my plugin, of the existance of the gorgeous link ?

  Read the article

• getting parameters from friendly url portlets jsr 286

  - by user265950

  link texthi, I am using ibm portal server. there is a link which is coming from external link. the url that is coming is as below http://localhost.us.deloitte.com:10040/wps/myportal/home/gm_assignee_label/gm_eoa_page?invoker=esb?agsnid=32984?asgnmtid=50085 home,gm_assignee_label,gm_eoa_page are friendly urls given to 3 different pages. things after the ? are the key value parameters. i want to retrieve these paramters when i click on the link above and my page gets loaded. i tried the below link as given by ibm. but it didnt help me my portlet.xml code is as below <?xml version="1.0" encoding="UTF-8"?> <portlet-app xmlns="http://java.sun.com/xml/ns/portlet/portlet-app_2_0.xsd" version="2.0" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://java.sun.com/xml/ns/portlet/portlet-app_2_0.xsd http://java.sun.com/xml/ns/portlet/portlet-app_2_0.xsd" id="com.ibm.faces.portlet.FacesPortlet.8b353a4492"> <portlet> <portlet-name>EndOfAssignmentPortlet</portlet-name> <display-name xml:lang="en">EndOfAssignmentPortlet</display-name> <display-name>EndOfAssignmentPortlet</display-name> <portlet-class>com.ibm.endofassignmentportlet.EndOfAssignmentPortlet</portlet-class> <init-param> <name>com.ibm.faces.portlet.page.view</name> <value>/view/endofassignment/EOASearchAssignment.jsp</value> </init-param> <init-param> <name>wps.markup</name> <value>html</value> </init-param> <init-param> <name>com.sun.faces.portlet.SAVE_REQUEST_SCOPE</name> <value>true</value> </init-param> <expiration-cache>0</expiration-cache> <supports> <mime-type>text/html</mime-type> <portlet-mode>view</portlet-mode> <portlet-mode>EDIT</portlet-mode> <portlet-mode>HELP</portlet-mode> </supports> <supported-locale>en</supported-locale> <resource-bundle> com.ibm.endofassignmentportlet.nl.EndOfAssignmentPortletResource</resource-bundle> <portlet-info> <title>EndOfAssignmentPortlet</title> <short-title>EndOfAssignmentPortlet</short-title> <keywords>EndOfAssignmentPortlet</keywords> </portlet-info> <supported-public-render-parameter>AssigneeID</supported-public-render-parameter> <supported-public-render-parameter>AssignmentID</supported-public-render-parameter> <supported-public-render-parameter>InvokerID</supported-public-render-parameter> </portlet> <default-namespace>http://EndOfAssignmentPortlet/</default-namespace> <public-render-parameter> <identifier>AssigneeID</identifier> <qname xmlns:x="http://localhost.us.deloitte.com:10040/wps/myportal">x:agsnid</qname> </public-render-parameter> <public-render-parameter> <identifier>AssignmentID</identifier> <qname xmlns:x="http://localhost.us.deloitte.com:10040/wps/myportal">x:asgnmtid</qname> </public-render-parameter> <public-render-parameter> <identifier>InvokerID</identifier> <qname xmlns:x="http://localhost.us.deloitte.com:10040/wps/myportal">x:invoker</qname> </public-render-parameter> </portlet-app> i am trying to get the values in my doView method of portlet as below String esbAssigneeID = request.getParameter("agsnid"); But i always get null. please help. TIA, Tejas

  Read the article

• HTML/CSS - Website Help.

  - by gabeaudick

  I'm trying to build my first website from scratch. I mocked up the design in Photoshop, and have been trying to convert into code for a few hours. But I haven't got far. In fact, I'm stuck on the header's navigation bar. It looks right, but it doesn't work. I'm using an unordered-inline list, and trying to link different rectangles in the header. I can't click on anything in the header, though. The code for the html and css files, and a mockup of the header, are below. Any advice on why the header bar isn't working would be much appreciated. Here's a link to the image: http://rookery9.aviary.com.s3.amazonaws.com/3961000/3961027_eb89_625x625.jpg *Ideally, you would be able to click on either "". home.html: <!DOCTYPE HTML PUBLIC "-//W3C//DTD XHTML 1.0 Strict//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-strict.dtd"> <html xmlns="http://www.w3.org/1999/xhtml" lang="en" xml:lang="en"> <head> <!-- Title --> <title>I am Gabe Audick.</title> <!-- Meta --> <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> <meta name="Author" content="Gabe Audick" /> <meta name="Copyright" content="Gabe Audick" /> <!-- Stylesheets --> <link href="style.css" media="screen" rel="stylesheet" type="text/css" /> <!-- RSS --> <link rel="alternate" type="application/rss+xml" title="gabeaudick RSS" href="http://feeds.feedburner.com/gabeaudick" /> </head> <body> <!-- Navigation Bar --> <div id="wrap"> <div id="header"> <ul> <li><a href="#">Previous</a></li> <li><a href="#">Home</a></li> <li><a href="#">Next</a></li> </ul> </div> </div> <!-- END --> <!-- Google Analytics --> <script type="text/javascript"> var _gaq = _gaq || []; _gaq.push(['_setAccount', 'UA-5899101-4']); _gaq.push(['_trackPageview']); (function() { var ga = document.createElement('script'); ga.type = 'text/javascript'; ga.async = true; ga.src = ('https:' == document.location.protocol ? 'https://ssl' : 'http://www') + '.google-analytics.com/ga.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(ga, s); })(); </script> <!-- End of Google Analytics --> </body> </html> style.css: * { margin: 0; padding: 0; } body { background-color: #fff; color: #000; font-size: 14px; font-family: 'Century Gothic', Helvetica, sans-serif; position: relative; } #wrap { background-color: #000; color: #fbead; height: 26px; width: 100%; } #header { background: url(./images/home.gif) center no-repeat #000; height: 26px; } #header ul li{ float:left; list-style-type:none; margin-right:12px; text-indent:-9999px; } #header li a:link, #header li a:visited{ outline:none; display:block; height:26px; text-indent:-9999px; }

  Read the article

• Gnome-Network-Manager Config File Migration

  - by Jorge

  I think I have an issue with gnome-network-manager, I used to have a lot of connections configured, Wireless, Wired and VPN. After upgrading to 12.04 (from 11.10) I lost every configuration. I realized that the configs that used to be saved in $HOME/.gconf/system/networking/connections now are being saved in /etc/NetworkManager/system-connections/. I don't know how to migrate my settings to the new config file format Can anybody help me? jorge@thinky:~$ sudo lshw -C network *-network description: Ethernet interface product: 82566MM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:1f:e2:14:5a:9b capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.5.1-k firmware=0.3-0 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:fe000000-fe01ffff memory:fe025000-fe025fff ioport:1840(size=32) *-network description: Wireless interface product: PRO/Wireless 4965 AG or AGN [Kedron] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 61 serial: 00:21:5c:32:c2:e5 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwl4965 driverversion=3.2.0-23-generic-pae firmware=228.61.2.24 ip=192.168.2.103 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:df3fe000-df3fffff jorge@thinky:~$ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04 LTS Release: 12.04 Codename: precise jorge@thinky:~$ uname -a Linux thinky 3.2.0-23-generic-pae #36-Ubuntu SMP Tue Apr 10 22:19:09 UTC 2012 i686 i686 i386 GNU/Linux jorge@thinky:~$ dpkg -l | grep -i firm ii linux-firmware 1.79 Firmware for Linux kernel drivers

  Read the article

• Tomcat stops responding to JK requests

  - by Bruno Reis

  Hello. I have a nasty issue with load-balanced Tomcat servers that are hanging up. Any help would be greatly appreciated. The system I'm running Tomcat 6.0.26 on HotSpot Server 14.3-b01 (Java 1.6.0_17-b04) on three servers sitting behind another server that acts as load balancer. The load balancer runs Apache (2.2.8-1) + MOD_JK (1.2.25). All of the servers are running Ubuntu 8.04. The Tomcat's have 2 connectors configured: an AJP one, and a HTTP one. The AJP is to be used with the load balancer, while the HTTP is used by the dev team to directly connect to a chosen server (if we have a reason to do so). I have Lambda Probe 1.7b installed on the Tomcat servers to help me diagnose and fix the problem soon to be described. The problem Here's the problem: after about 1 day the application servers are up, JK Status Manager starts reporting status ERR for, say, Tomcat2. It will simply get stuck on this state, and the only fix I've found so far is to ssh the box and restart Tomcat. I must also mention that JK Status Manager takes a lot longer to refresh when there's a Tomcat server in this state. Finally, the "Busy" count of the stuck Tomcat on JK Status Manager is always high, and won't go down per se -- I must restart the Tomcat server, wait, then reset the worker on JK. Analysis Since I have 2 connectors on each Tomcat (AJP and HTTP), I still can connect to the application through the HTTP one. The application works just fine like this, very, very fast. That is perfectly normal, since I'm the only one using this server (as JK stopped delegating requests to this Tomcat). To try to better understand the problem, I've taken a thread dump from a Tomcat which is not responding anymore, and from another one that has been restarted recently (say, 1 hour before). The instance that is responding normally to JK shows most of the TP-ProcessorXXX threads in "Runnable" state, with the following stack trace: java.net.SocketInputStream.socketRead0 ( native code ) java.net.SocketInputStream.read ( SocketInputStream.java:129 ) java.io.BufferedInputStream.fill ( BufferedInputStream.java:218 ) java.io.BufferedInputStream.read1 ( BufferedInputStream.java:258 ) java.io.BufferedInputStream.read ( BufferedInputStream.java:317 ) org.apache.jk.common.ChannelSocket.read ( ChannelSocket.java:621 ) org.apache.jk.common.ChannelSocket.receive ( ChannelSocket.java:559 ) org.apache.jk.common.ChannelSocket.processConnection ( ChannelSocket.java:686 ) org.apache.jk.common.ChannelSocket$SocketConnection.runIt ( ChannelSocket.java:891 ) org.apache.tomcat.util.threads.ThreadPool$ControlRunnable.run ( ThreadPool.java:690 ) java.lang.Thread.run ( Thread.java:619 ) The instance that is stuck show most (all?) of the TP-ProcessorXXX threads in "Waiting" state. These have the following stack trace: java.lang.Object.wait ( native code ) java.lang.Object.wait ( Object.java:485 ) org.apache.tomcat.util.threads.ThreadPool$ControlRunnable.run ( ThreadPool.java:662 ) java.lang.Thread.run ( Thread.java:619 ) I don't know of the internals of Tomcat, but I would infer that the "Waiting" threads are simply threads sitting on a thread pool. So, if they are threads waiting inside of a thread pool, why wouldn't Tomcat put them to work on processing requests from JK? Solution? So, as I've stated before, the only fix I've found is to stop the Tomcat instance, stop the JK worker, wait the latter's busy count slowly go down, start Tomcat again, and enable the JK worker once again. What is causing this problem? How should I further investigate it? What can I do to solve it? Thanks in advance.

  Read the article

• two possible wifi devices competing, one is hard blocked

  - by patrickmw

  blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

  Read the article

• two possible wifi devices competing, one is hard blocked - unable to connect wireless

  - by patrickmw

  blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff contents of /var/lib/NetworkManager/NetworkManager.state [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

  Read the article

• Getting Started with jqChart for ASP.NET Web Forms

  - by jqChart

  Official Site | Samples | Download | Documentation | Forum | Twitter Introduction jqChart takes advantages of HTML5 Canvas to deliver high performance client-side charts and graphs across browsers (IE 6+, Firefox, Chrome, Opera, Safari) and devices, including iOS and Android mobile devices. Some of the key features are: High performance rendering. Animaitons. Scrolling/Zoooming. Support for unlimited number of data series and data points. Support for unlimited number of chart axes. True DateTime Axis. Logarithmic and Reversed axis scale. Large set of chart types - Bar, Column, Pie, Line, Spline, Area, Scatter, Bubble, Radar, Polar. Financial Charts - Stock Chart and Candlestick Chart. The different chart types can be easily combined.  System Requirements Browser Support jqChart supports all major browsers: Internet Explorer - 6+ Firefox Google Chrome Opera Safari jQuery version support jQuery JavaScript framework is required. We recommend using the latest official stable version of the jQuery library. Visual Studio Support jqChart for ASP.NET does not require using Visual Studio. You can use your favourite code editor. Still, the product has been tested with several versions of Visual Studio .NET and you can find the list of supported versions below: Visual Studio 2008 Visual Studio 2010 Visual Studio 2012 ASP.NET Web Forms support Supported version - ASP.NET Web Forms 3.5, 4.0 and 4.5 Installation Download and unzip the contents of the archive to any convenient location. The package contains the following folders: [bin] - Contains the assembly DLLs of the product (JQChart.Web.dll) for WebForms 3.5, 4.0 and 4.5. This is the assembly that you can reference directly in your web project (or better yet, add it to your ToolBox and then drag & drop it from there). [js] - The javascript files of jqChart and jqRangeSlider (and the needed libraries). You need to include them in your ASPX page, in order to gain the client side functionality of the chart. The first file is "jquery-1.5.1.min.js" - this is the official jQuery library. jqChart is built upon jQuery library version 1.4.3. The second file you need is the "excanvas.js" javascript file. It is used from the versions of IE, which dosn't support canvas graphics. The third is the jqChart javascript code itself, located in "jquery.jqChart.min.js". The last one is the jqRangeSlider javascript, located in "jquery.jqRangeSlider.min.js". It is used when the chart zooming is enabled. [css] - Contains the Css files that the jqChart and the jqRangeSlider need. [samples] - Contains some examples that use the jqChart. For full list of samples plese visit - jqChart for ASP.NET Samples. [themes] - Contains the themes shipped with the products. It is used from the jqRangeSlider. Since jqRangeSlider supports jQuery UI Themeroller, any theme compatible with jQuery UI ThemeRoller will work for jqRangeSlider as well. You can download any additional themes directly from jQuery UI's ThemeRoller site available here: http://jqueryui.com/themeroller/ or reference them from Microsoft's / Google's CDN. <link rel="stylesheet" type="text/css" media="screen" href="http://ajax.aspnetcdn.com/ajax/jquery.ui/1.8.21/themes/smoothness/jquery-ui.css" /> The final result you will have in an ASPX page containing jqChart would be something similar to that (assuming you have copied the [js] to the Script folder and [css] to Content folder of your ASP.NET site respectively). <%@ Page Language="C#" AutoEventWireup="true" CodeBehind="Default.aspx.cs" Inherits="samples_cs.Default" %> <%@ Register Assembly="JQChart.Web" Namespace="JQChart.Web.UI.WebControls" TagPrefix="jqChart" %> <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html > <head runat="server"> <title>jqChart ASP.NET Sample</title> <link rel="stylesheet" type="text/css" href="~/Content/jquery.jqChart.css" /> <link rel="stylesheet" type="text/css" href="~/Content/jquery.jqRangeSlider.css" /> <link rel="stylesheet" type="text/css" href="~/Content/themes/smoothness/jquery-ui-1.8.21.css" /> <script src="<% = ResolveUrl("~/Scripts/jquery-1.5.1.min.js") %>" type="text/javascript"></script> <script src="<% = ResolveUrl("~/Scripts/jquery.jqRangeSlider.min.js") %>" type="text/javascript"></script> <script src="<% = ResolveUrl("~/Scripts/jquery.jqChart.min.js") %>" type="text/javascript"></script> <!--[if IE]><script lang="javascript" type="text/javascript" src="<% = ResolveUrl("~/Scripts/excanvas.js") %>"></script><![endif]--> </head> <body> <form id="form1" runat="server"> <asp:ObjectDataSource ID="ObjectDataSource1" runat="server" SelectMethod="GetData" TypeName="SamplesBrowser.Models.ChartData"></asp:ObjectDataSource> <jqChart:Chart ID="Chart1" Width="500px" Height="300px" runat="server" DataSourceID="ObjectDataSource1"> <Title Text="Chart Title"></Title> <Animation Enabled="True" Duration="00:00:01" /> <Axes> <jqChart:CategoryAxis Location="Bottom" ZoomEnabled="true"> </jqChart:CategoryAxis> </Axes> <Series> <jqChart:ColumnSeries XValuesField="Label" YValuesField="Value1" Title="Column"> </jqChart:ColumnSeries> <jqChart:LineSeries XValuesField="Label" YValuesField="Value2" Title="Line"> </jqChart:LineSeries> </Series> </jqChart:Chart> </form> </body> </html>   Official Site | Samples | Download | Documentation | Forum | Twitter

  Read the article

• 12.04 wired network doesn't work RTL8111/8168B

  - by laket

  its a fresh 12.04 install 64bits. wifi works fine, wired stays off with cable connected and network-manager shows as if cable is disconnected. Turning off networking lights up my network-cards leds, turning networking on shuts off the leds and no communication is possible. I already tried, turning off the network-manager (sudo service network-manager stop) and setting up my eth0 manually, as soon as I switch off the network-manager my leds light up, but after setting up manually eth0 (sudo ifconfig eth0 10.2.10.114 netmask 255.255.0.0 up) the leds turn off again. I am still dual booting with 10.04 where I have no issues at all, leaving the cable connected all time to my notebook and a switch. Here is some hardware info: lshw: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 03 serial: c8:0a:a9:d7:05:97 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168d-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff memory:f0010000-f001ffff lspci: 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) ifconfig eth0: eth0 Link encap:Ethernet HWaddr c8:0a:a9:d7:05:97 inet addr:10.2.10.114 Bcast:10.2.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0xc000 cat /etc/network/interfaces: (already tried here with and w/o eth0) auto lo eth0 iface lo inet loopback cat /etc/NetworkManager/NetworkManager.conf [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false Any help is welcome ;) Laket

  Read the article

• wifi not working hp dv4

  - by Blaze

  i get this output for sudo lshw -C network : *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 06 serial: 3c:4a:92:cd:63:98 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network DISABLED description: Wireless interface product: RT5390 [802.11 b/g/n 1T1R G-band PCI Express Single Chip] vendor: Ralink corp. physical id: 0 bus info: pci@0000:0a:00.0 logical name: wlan0 version: 00 serial: 90:00:4e:82:3c:5b width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.0.0-17-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c2500000-c250ffff i cant enable the wifi using the fn+f12 key.. its just stuck. In windows 7 it gets enabled when i press the same keys. but this happens after it gets booted up... i just want to use the wifi in anyway possible. can anybody help?

  Read the article

• Dell inspiron not finding Vodafone router

  - by Jeggy

  I have a "Dell inspiron 1564" and ubuntu doesn't find my friends router it works great at home, he has a vodafone router jeggy@jeggy-XPS:~$ sudo lshw -C network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: 78:e4:00:2a:d1:eb width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f0200000-f0203fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: b8:ac:6f:67:32:52 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:f0410000-f0410fff memory:f0400000-f040ffff memory:f0420000-f043ffff *-network description: Ethernet interface physical id: 4 logical name: ham0 serial: 7a:79:05:ff:3e:ec size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.255.62.236 link=yes multicast=yes port=twisted pair speed=10Mbit/s

  Read the article

• "Enable Wireless" option is disabled in network settings

  - by silenTK

  I'm using Ubuntu 11.10 (dual booted with Windows 7) but I'm unable to access Internet wireless even though I can do so on Windows 7. The output for rfkill list all is given below: rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no The output for sudo lshw -C network *-network DISABLED is: description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 01 serial: 11:11:11:11:11:11 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:16 memory:c2500000-c2503fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 05 serial: 22:22:22:22:22:22 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff Broadcom STA wireless driver is installed, activated, and currently in use. My laptop is a HP-Pavilion-g6-1004tx. My hardware switch is on. Enable Wireless option is also disabled in network settings.

  Read the article

• Twitter Bootstrap Collapsible Navbar Duplicating

  - by sixeightzero

  I am working on a project using Twitter Bootstrap. One thing that I noticed is that my pages have duplicate navbars when they are defined as collapsible and the page is resized smaller. Here is the duplicate NavBar: Here is the normal width NavBar: Code: <!DOCTYPE html> <html lang="en"> <!--[if lt IE 7]> <html class="no-js lt-ie9 lt-ie8 lt-ie7"> <![endif]--> <!--[if IE 7]> <html class="no-js lt-ie9 lt-ie8"> <![endif]--> <!--[if IE 8]> <html class="no-js lt-ie9"> <![endif]--> <!--[if gt IE 8]><!--> <html class="no-js"> <!--<![endif]--> <head> <meta charset="utf-8"> <meta http-equiv="X-UA-Compatible" content="IE=edge,chrome=1"> <title></title> <meta name="description" content=""> <meta name="viewport" content="width=device-width"> <link rel="stylesheet" href="/assets/css/bootstrap.css"> <style> body { padding-top: 60px; } </style> <link rel="stylesheet" href="/assets/css/bootstrap-responsive.min.css"> <link rel="stylesheet" href="/assets/css/main.css"> <script>window.jQuery || document.write('<script src="/assets/js/vendor/jquery-1.8.1.min.js"><\/script>')</script> <script src="/assets/js/vendor/modernizr-2.6.1-respond-1.1.0.min.js"></script> </head> <body class="dark"> <!--[if lt IE 9]> <p class="chromeframe">You are using an outdated browser. <a href="http://browsehappy.com/">Upgrade your browser today</a> or <a href="http://www.google.com/chromeframe/?redirect=true">install Google Chrome Frame</a> to better experience this site.</p> <![endif]--> <div class="navbar navbar-inverse navbar-fixed-top"> <div class="navbar-inner"> <div class="container"> <a class="btn btn-navbar" data-toggle="collapse" data-target=".nav-collapse"> <span class="icon-bar"></span> <span class="icon-bar"></span> <span class="icon-bar"></span> </a> <a class="brand" href="#">Project name</a> <div class="nav-collapse collapse"> <ul class="nav"> <li class="active"><a href="#">Home</a></li> <li><a href="#about">About</a></li> <li><a href="#contact">Contact</a></li> <li class="dropdown"> <a href="#" class="dropdown-toggle" data-toggle="dropdown">Dropdown <b class="caret"></b></a> <ul class="dropdown-menu"> <li><a href="#">Action</a></li> <li><a href="#">Another action</a></li> <li><a href="#">Something else here</a></li> <li class="divider"></li> <li class="nav-header">Nav header</li> <li><a href="#">Separated link</a></li> <li><a href="#">One more separated link</a></li> </ul> </li> </ul> </div><!--/.nav-collapse --> </div> </div> </div> Has anyone else run into this and have some pointers?

  Read the article

• Wireless doesn't work after installing 11.10

  - by Ingram

  I just did a fresh install of 11.10 32 bit and I can't get my wireless to work. I installed the drivers the Broadcom STA wireless drivers through additional drivers and rebooted, but it still doesn't see any wireless networks Did something change in 11.10 that makes the wireless card not work anymore? I was using 10.10 before, and it worked fine. Do I need to go back to 10.10? sudo lshw -C network [sudo] password for user1: *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 10 serial: 00:1f:16:be:55:ff size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=sb v2.19 ip=192.168.0.70 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:f0300000-f030ffff *-network UNCLAIMED description: Network controller product: BCM4311 802.11b/g WLAN vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0400000-f0403fff

  Read the article

• Missing driver ASUS PCE-N53 11n N600 PCI-E Adapter

  - by oyse

  I have problems with getting an Asus PCE-N53 11n N600 PCI-E Adapter card to work on my desktop computer. As far as I can tell no drivers are installed for the card. I know I can manually download the drivers directly from Asus, but I would rather not go that route. If there are anyone that knows about any packages or other things I can do to make this work would be much appreciated. Some systems details: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise $ sudo lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: d4:3d:7e:03:b9:1d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.0.173 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:d000(size=256) memory:f2104000-f2104fff memory:f2100000-f2103fff *-network UNCLAIMED description: Network controller product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7100000-f710ffff $ lsmod Module Size Used by nvidia 12319264 51 vesafb 13844 1 snd_hda_codec_hdmi 32474 1 joydev 17693 0 bnep 18281 2 rfcomm 47604 0 bluetooth 180104 10 bnep,rfcomm snd_hda_codec_realtek 224173 1 snd_seq_midi 13324 0 ppdev 17113 0 snd_rawmidi 30748 1 snd_seq_midi usbhid 47199 0 hid 99559 1 usbhid nouveau 774641 0 parport_pc 32866 1 snd_hda_intel 33773 5 ttm 76949 1 nouveau snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel drm_kms_helper 46978 1 nouveau drm 242038 3 nouveau,ttm,drm_kms_helper snd_seq_midi_event 14899 1 snd_seq_midi snd_hwdep 13668 1 snd_hda_codec snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event i2c_algo_bit 13423 1 nouveau mxm_wmi 12979 1 nouveau wmi 19256 1 mxm_wmi mac_hid 13253 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec psmouse 97362 0 video 19596 1 nouveau snd_timer 29990 2 snd_seq,snd_pcm snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq,snd_pcm,snd_timer,snd_seq_device serio_raw 13211 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp r8169 62099 0

  Read the article

• wireless card not detected

  - by user281219

  i have a old HP Compaq NX6125 with a new lunbuntu 14.04 32 bits install , but the wireless card is not working I have already done this steps and the wireless leds on the laptop are on but can't see any where the wireless interface , cloud`t do the last two steps . sudo apt-get remove bcmwl-kernel-source sudo apt-get install firmware-b43-installer b43-fwcutter Then Reboot And you need to activate the card from settings/network/wireless make it ON After this search for wireless icon at the task bar and look for your wifi. lshw -class network: *-network:0 description: Ethernet interface product: NetXtreme BCM5788 Gigabit Ethernet vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:02:01.0 logical name: eth0 version: 03 serial: 00:0f:b0:f7:d1:0f size: 100Mbit/s capacity: 1Gbit/s width: 32 bits clock: 66MHz capabilities: pm vpd msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.134 duplex=full firmware=5788-v3.26 ip=192.168.1.120 latency=64 link=yes mingnt=64 multicast=yes port=twisted pair speed=100Mbit/s resources: irq:23 memory:d0000000-d000ffff *-network:1 description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 2 bus info: pci@0000:02:02.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:22 memory:d0010000-d0011fff *-network description: Wireless interface physical id: 1 logical name: wlan2 serial: 00:14:a5:77:9e:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.13.0-29-generic firmware=666.2 link=no multicast=yes wireless=IEEE 802.11bg

  Read the article

• Wireless drivers

  - by Kencer

  The results for my laptop are as below. How will i install wireless drivers and graphics? $ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) $ sudo lshw -c network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0500000-f0507fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 07 serial: 3c:97:0e:85:c0:0d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=172.16.96.36 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no

  Read the article

• JSF composite component - weird behavior when trying to save state

  - by jc12

  I'm using Glassfish 3.2.2 and JSF 2.1.11 I'm trying to create a composite component that will take as parameters a string and a max number of characters and then will show only the max amount of characters, but it will have a "more" link next to it, that when clicked will expand the text to the full length and will then have a "less" link next to it to take it back to the max number of characters. I'm seeing some weird behavior, so I'm wondering if I'm doing something wrong. Here is my composite component definition: <html xmlns="http://www.w3.org/1999/xhtml" xmlns:composite="http://java.sun.com/jsf/composite" xmlns:h="http://java.sun.com/jsf/html" xmlns:fn="http://java.sun.com/jsp/jstl/functions" xmlns:p="http://primefaces.org/ui"> <composite:interface componentType="expandableTextComponent"> <composite:attribute name="name" required="true"/> <composite:attribute name="maxCharacters" required="true"/> <composite:attribute name="value" required="true"/> </composite:interface> <composite:implementation> <h:panelGroup id="#{cc.attrs.name}"> <h:outputText value="#{fn:substring(cc.attrs.value, 0, cc.attrs.maxCharacters)}" rendered="#{fn:length(cc.attrs.value) le cc.attrs.maxCharacters}"/> <h:outputText value="#{fn:substring(cc.attrs.value, 0, cc.attrs.maxCharacters)}" rendered="#{fn:length(cc.attrs.value) gt cc.attrs.maxCharacters and !cc.expanded}" style="margin-right: 5px;"/> <h:outputText value="#{cc.attrs.value}" rendered="#{fn:length(cc.attrs.value) gt cc.attrs.maxCharacters and cc.expanded}" style="margin-right: 5px;"/> <p:commandLink actionListener="#{cc.toggleExpanded()}" rendered="#{fn:length(cc.attrs.value) gt cc.attrs.maxCharacters}" update="#{cc.attrs.name}"> <h:outputText value="#{__commonButton.more}..." rendered="#{!cc.expanded}"/> <h:outputText value="#{__commonButton.less}" rendered="#{cc.expanded}"/> </p:commandLink> </h:panelGroup> </composite:implementation> </html> And here is the Java component: @FacesComponent("expandableTextComponent") public class ExpandableTextComponent extends UINamingContainer { boolean expanded; public boolean isExpanded() { return expanded; } public void toggleExpanded() { expanded = !expanded; } } Unfortunately expanded is always false every time the toggleExpanded function is called. However if I change the composite component to the following then it works. <html xmlns="http://www.w3.org/1999/xhtml" xmlns:composite="http://java.sun.com/jsf/composite" xmlns:h="http://java.sun.com/jsf/html" xmlns:fn="http://java.sun.com/jsp/jstl/functions" xmlns:p="http://primefaces.org/ui"> <composite:interface componentType="expandableTextComponent"> <composite:attribute name="name" required="true"/> <composite:attribute name="maxCharacters" required="true"/> <composite:attribute name="value" required="true"/> </composite:interface> <composite:implementation> <h:panelGroup id="#{cc.attrs.name}"> <h:outputText value="#{fn:substring(cc.attrs.value, 0, cc.attrs.maxCharacters)}" rendered="#{fn:length(cc.attrs.value) le cc.attrs.maxCharacters}"/> <h:outputText value="#{fn:substring(cc.attrs.value, 0, cc.attrs.maxCharacters)}" rendered="#{fn:length(cc.attrs.value) gt cc.attrs.maxCharacters and !cc.expanded}" style="margin-right: 5px;"/> <p:commandLink actionListener="#{cc.toggleExpanded()}" rendered="#{fn:length(cc.attrs.value) gt cc.attrs.maxCharacters and !cc.expanded}" update="#{cc.attrs.name}" process="@this"> <h:outputText value="#{__commonButton.more}..."/> </p:commandLink> <h:outputText value="#{cc.attrs.value}" rendered="#{fn:length(cc.attrs.value) gt cc.attrs.maxCharacters and cc.expanded}" style="margin-right: 5px;"/> <p:commandLink actionListener="#{cc.toggleExpanded()}" rendered="#{fn:length(cc.attrs.value) gt cc.attrs.maxCharacters and cc.expanded}" update="#{cc.attrs.name}" process="@this"> <h:outputText value="#{__commonButton.less}"/> </p:commandLink> </h:panelGroup> </composite:implementation> </html> If I place a breakpoint in the toggleExpanded function, it only gets called on the "more" link and not the "less" link. So the question is why doesn't it get called when I click on the "less" link? Shouldn't this code be equivalent to the code above? Is there a better way to save state in a component?

  Read the article

• Can't get wireless working after installing ubuntu 12.10 on acer aspire 5560-7414

  - by markdel

  I have been struggling all day trying different solutions from different posts on how to get my wifi working but none have worked. Any help would be greatly appreciated. Below are some wireless preferences to help find the problem. mark@mark-Aspire-5560:~$ sudo rfkill list all [sudo] password for mark: 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no *-network description: Ethernet interface product: NetLink BCM57785 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:6a:8a:7f:63:82 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=158.65.194.244 latency=0 link=yes multicast=yes port=twisted pair speed=10Mbit/s resources: irq:16 memory:f0000000-f000ffff memory:f0010000-f001ffff memory:f0050000-f00507ff *-network description: Wireless interface product: BCM43227 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 00 serial: 08:ed:b9:01:e0:8b width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.112 latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f0103fff

  Read the article

• wireless blocked after installing ubuntu 12.04

  - by Cornelia Frank

  I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

< Previous Page | 170 171 172 173 174 175 176 177 178 179 180 181  | Next Page >