Search Results

Search found 7241 results on 290 pages for 'casey hope'.

Page 176/290 | < Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >

• VPN Trunk Between Cisco ASA 5520 and DrayTek Vigor 2930

  - by David Heggie

  I'm a bit of a VPN newbie, so please go easy on me ... I'm trying to use the VPN trunking capabilities of the DrayTek Vigor 2930 firewall to bond two IPSec VPN connections to a Cisco ASA 5520 device and I'm getting myself tied in knots and hope someone here with more knowledge / experience can help. I have a remote site with two ADSL connections and the DrayTek box. The main office site has the Cisco ASA device. I am able to setup a single IPSec connection between the two sites on either of the ADSL connections' public IP addresses, but as soon as I try to use the VPN bonding, nothing works. The VPN tunnels are both still up, but the traffic is getting lost somewhere. I suspect it's due to the ASA not knowing how to route the traffic back over the VPN - one minute, traffic from my remote office's network is coming from public ip address #1, the next it's coming from public address #2 and it doesn't know what to do. Well, that's my newbie impression of what's going wrong, but I don't really know: If this is really what's happening If what I'm trying to do (bond two VPN connections from a single remote network to improve the bandwidth / resiliency) is possible with the kit I've got Could anyone help?

  Read the article

• windows 8.1 does not boot after CHKDSK command

  - by sepehr

  I had problem with Windows 8.1 high Disk usage so in order to solve , searched forums. A voted answer suggested to use CHKDSK command as follow: run command prompt and as administrator type code snippet below: CHKDSK /f /v /b C: (I can not remember accurately) CHKDSK printed : can not run CHKDSK right now , would you like to schedule C drive to be checked next time windows starts? (Y/N) my response was "Y" ,please ! Following this suggestion not only didn't solve my problem as expected but also added another one ! The next time system booted, after windows authentication I just could see a black screen and mouse pointer. So I force shut downed the system and tried to start windows again. This time , windows got stuck in Scanning and Repairing on 22% for around 3 hours so I got tired and forced shut downed again. is CHKDSK source of Scanning and Repairing problem or they are discrete ? is there any hope to overcome this problem without re-installing windows ? can any one else run CHKDSK on newer versions of windows without problem? is CHKDSK effective but inefficient ?(it finally get to end but will take a long time) If yes, how much time does it take? I also have Linux Ubuntu 14.04 installed along side windows.

  Read the article

• emacs error: "Symbol's value as variable is void: hostname"

  - by Florian Pilz

  After I installed emacs this error occurs every time on startup. It prevents me from installing plugins, e.g. auctex via aptitude. I already tried to install a plugin by hand (rails for ruby), but doesn't work. The error doesn't contain the message "hostname", but the hostname of my PC is displayed ("bloodredangel-ubuntu"). I changed my hostname to "bloodredangel", but the error message stays the same. While I changed my hostname I saw that in /etc/hostname were two entries: 127.0.0.1 bloodredangel-ubuntu I already asked this question in an ubuntu forum but they couldn't help. They recognised an misconfigured /etc/hosts file, which I corrected, but from time to time these incorrect configurations get attached by something. I didn't add them by hand, maybe it has something to do with the issue. The misconfigurations looked like this: 127.0.0.1 127.0.0.1 bloodredangel-ubuntu localhost.localdomain localhost 127.0.0.1 127.0.0.1:8080 bloodredangel-ubuntu localhost.localdomain localhost I didn't found a solution on the internet, so I hope I will find help here finally.

  Read the article

• Import exponetial fixed width format data into Excel

  - by Tom Daniel

  I've received a bunch of text data files consiting of Lots of records (30K/file) of 3 fields each of 5-place numbers in exponential format: s0.nnnnnEsee (where s is +/-, n is a digit and ee is the exponent (always 2 digit). When I open the file in Notepad, the format is perfectly uniform throughout each file, but when I import it to Excel using Data|Import|Fixed Width, many of the data values get messed up, no matter what format (text, exponential, various custom tries) I assign to the cells. Looking at the Notepad version, it appears that leading + signs were replaced with a space in the data file, but the sign of the exponential is always there. This means that some fields begin with a space, and this appears to confuse the Excel import routine. I get the same result in Excel 2003 and 2007. I'm sure there's a straightforward solution (hopefully without a messy VBA routine), but I can't figure out what to try next. :-) To clarify (hopefully), here are some input records and the corresponding text input to Excel: Notepad Excel -0.11311E+01 0.10431E-04 0.27018E-03 -0.11311E 1.0431E-05 2.7018E-04 0.19608E+00-0.81414E-02-0.89553E-02 0.19608E -8.1414E-03 8.9553E-03 etc. Whoopee! Solved my own problem - in the spirit of Jeopardy, now that I've begun the question, here's the answer - Use a different "File Origin" - several other than the default "Unicode UTF..." work fine! What a pain. Hope this helps somebody else avoid a few unpleasant hours! Aloha from Kona, Tom

  Read the article

• How do I export address book from N97

  - by mplungjan

  Hi, I need to copy my numbers from my private Nokia to my office BB. I have not found a way to export my phone numbers from ovi or elsewhere. On Mac iSync stopped working with snow leopard and OVI on windows does not export. I do not mind using a windows suggestion. I lost a description on how to use the ovi backup files in another program. What I have done so far terminal: sudo open -a iSync.app - it launched but iSync said "this device is not supported by iSync" went here http://europe.nokia.com/support/product-support/isync/compatibility-and-download found a plugin (I am sure that was not there a while ago :| ) Checked software version 22.0.110 installed plugin Ran iSync which found and installed my N97 device successfully. synced. It stopped with The connection was lost while talking to the phone. http://discussions.europe.nokia.com/t5/Nseries-and-S60-Smartphones/N97-iSync-Multimedia-Transfer-Modem/m-p/568560 no news since Jan 2010. Tried to download and install http://best-vcard.en.softonic.com/symbian but the installer fails :( I simply do not understand why Nokia is giving us such a hard time. I would not have considered switching from Nokia if Mac had been better supported. It is so frustrating that they just seem not to care losing Nokia fanbois like me - especially since I am this outspoken on the net and what i say on popular forums gets indexed by google fast. I am very close to just go iPhone here. Hope someone has Nokia's ears UPDATE: I Downloaded NbuExplorer from sourceforge. It will extract everything from an OVI backup into VCF, VCS and VMG files. Very useful software and free.

  Read the article

• Powershell script to delete sub folders and files if creation date is >7 days but maintain parent folders of sub folders and files <7 days old

  - by Mark

  I'm currently using the Powershell script below to delete all files directories and sub directories of "$dump_path" that are seven days or older based upon the creation date and not modified date. The problem with this script is this: If folder "A" is seven (or more) days old it will be deleted even if its sub folders and files are less then seven days old. What I would like this script to do is this: Delete all files from the root and in all sub folders of "$dump_path" that are seven or more days old but maintain the parent folder(s) of files and folders that are less than seven days old even if that means the parent folders are more than seven days old. If all subfolders and files are seven days or older than the parent folder then the parent can be deleted. Slightly obscure problem I know, but the intention is to have a 7 day retention period of all data in a 'sandbox' location of our shared areas. Also, an added bonus if it could generate a log of what it deletes and e-mails it out post deletion. Thank you for reading and I hope that all makes sense! Mark # set folder path $dump_path = "c:\temp" # set minimum age of files and folders $max_days = "-7" # get the current date $curr_date = Get-Date # determine how far back we go based on current date $del_date = $curr_date.AddDays($max_days) # delete the files and folders Get-ChildItem $dump_path | Where-Object { $_.CreationTime -lt $del_date } | Remove-Item -Recurse

  Read the article

• Advance DNS - Redirecting Emails to new webhost

  - by Martin

  I am not to sure if this question belongs here but I will surely find out soon enough. I have two web hosts (Not sure why it has been setup this way but it has). I do not want to use the original web host to handle the emails as the Data that we get from them is 500 mb which is already full with hosting the website. The second web host has an unlimited data plan and was created so we could use this host for the email accounts. Now the problem is I have reset the Advance DNS Zone records on both accounts and I am not sure what they were before. (Silly me should have taken a backup of how it was setup before hand I know) Emails were working before and going to the second hosts server now they are going to the first host but it has no email addresses setup for use so all emails are bouncing saying that the address does not exist. Host 1 IP: 192.185.96.110 Host 2 IP: 27.54.88.66 So far I have changed the Advanced DNS Zone record on Host 1 with the following: A Record: mail.australisinstitute.qld.edu.au - 27.54.88.66 I have not made any changes on Host 2 and both hosts have the default MX Records. If I need to provide any more information I can but I just hope someone can decipher what I have said haha. Cheers in advance!

  Read the article

• Slow performance on VMWare Linux server after Tomcat install

  - by Loftx

  We have a VMWare ESXi 4.1 server hosting a number of Linux and Windows guests. Recently a new Linux guest was added to this server and seemed to be performing well. Tomcat and some other applications on this server were then installed which seem to have caused the server to run really slowly without any obvious resource issues. Slow performance include: The time taken to bring up the password prompt over ssh takes a few seconds when it was previously instantaneous. The time taken to unzip a zip file which was previously a few seconds now takes around 30 seconds The time taken to compile vmware tools has increased by similar factors Both the VMWare console and monitoring commands don't report any issues with high CPU or memory usage but something is obviously slowing the server down somehow. Does anyone have any ideas what may be causing this issue and how it can be resolved? Thanks, Tom Edit As per your questions I’ve looked at some of the performance indicators on both the VM host and VM guest indicated. Firstly I tried reserving the full amount of memory (3gb) for this VM – no other machines on this server have any memory reservation. The swap in rate and swap out rate for the VM host and guest are now both zero. Balloon memory on the guest is zero and on the host is 3.5gb (total memory on the host is 12gb) The swap rate for the guest is also zero. Swap used by the host is 200mb on average. Compression and decompression rates for the host and guest are zero. Command aborts for the host are zero. Read latency is very low – maximum 10ms average 0.8ms. Write latency is higher – a few spikes to 170ms but mostly around 25ms – is this bad? Queue command latency is zero . Physical disk read latency averages 5ms but often 10ms Physical disk write latency averages 15ms but is often 20ms I hope this helps - let me know if you need any more information.

  Read the article

• Unzipping archives, preserving folder hierarchy

  - by Hydrangea

  I've got a problem and am not sure what it is, but hope someone can help me think this through because this has me stumped. Backstory: I wrote a Java app (Android) that unzips some zip files downloaded from the network. Until now, this was working great. Then, this week, the archives that I'm creating on my pc (in Ubuntu 12.04) unzip on the Android phone into a flat hierarchy instead of preserving the folders. I'm creating the archives the same way (right-click on folder compress) but even though my old archives (created in 10.04) still unzip as expected, the new ones don't. On Ubuntu, the new zip files look the same to me as the old ones. When unzipped on my pc the folders in these new archives are restored the same as the old ones... it's the Android app that extracts the old ones fine and the new ones flat. What I really want to know, though, is what the difference between the archives is. Question: How could one determine why one zip archive would be extracted with folder hierarchy preserved, when an identical one (to all appearances on Ubuntu 12.04) is extracted with no hierarchy? Are there different ways in which a .zip file can "have" folders, but Ubuntu doesn't distinguish between them?

  Read the article

• How do photoshop slices and layer comps interact?

  - by Steve314

  I'm interested in using Photoshop (I have CS2) for some user interface design. I was hoping to be able to use slices and layer comps to mark out particular elements, and use Javascript scripting to export multiple graphics files and text descriptions (positions and sizes of slices mainly) that will be used by my program. My problem is that I've never used Photoshop for web design, or otherwise used slices, and I'm not confident that I understand how they interact with layer comps. This is what I believe (and hope) is correct... Manual slices aren't affected by layer comps in any way - they aren't saved as part of a layer comp. The same manual slices will be active irrespective of which layer comp is selected. Layer-based slices aren't directly affected by layer comps, but they are indirectly affected in that the layer comp saves details of layer position and style. Thus selecting a layer comp may move a layer and change its style, affecting the location and size of its layer-based slice, or may effectively disable the slice by hiding the layer. Automatic slices aren't directly affected by layer comps, but are indirectly affected due to changes to the layer-based slices. So, layer based slices (which are my main interest) may move, may change size (to accomodate a style such as a drop shadow), and may be effectively disabled by the layer being hidden. Other details (and all details of manual slices) will remain constant irrespective of which layer comp is active. Is that correct?

  Read the article

• Fatal Execution Engine Error on the Windows2008 r2, IIS7.5

  - by user66524

  Hi Guys We are running some asp.net(3.5) applications on the Windows2008 r2, IIS7.5. Recently we got some event logs so difficult, we have not idea hope some guys can help. 1.EventID: 1334 (9-1-2011 8:41:57) Error message An error occurred during a process host idle check. Exception: System.AccessViolationException Message: Attempted to read or write protected memory. This is often an indication that other memory is corrupt. StackTrace: at System.Collections.Hashtable.GetEnumerator() at System.Web.Hosting.ApplicationManager.IsIdle() at System.Web.Hosting.ProcessHost.IsIdle() 2.EventID: 1023 (9-1-2011 19:44:02) Error message .NET Runtime version 2.0.50727.4952 - Fatal Execution Engine Error (742B851A) (80131506) 3.EventID: 1000 (9-1-2011 19:44:03) Error message Faulting application name: w3wp.exe, version: 7.5.7600.16385, time stamp: 0x4a5bcd2b Faulting module name: mscorwks.dll, version: 2.0.50727.4952, time stamp: 0x4bebd49a Exception code: 0xc0000005 Fault offset: 0x0000c262 Faulting process id: 0x%9 Faulting application start time: 0x%10 Faulting application path: %11 Faulting module path: %12 Report Id: %13 4.EventID: 5011 (9-1-2011 19:44:03) Error message A process serving application pool 'AppPoolName' suffered a fatal communication error with the Windows Process Activation Service. The process id was '2552'. The data field contains the error number. 5.some info: we got the memory.hdmp(234MB) and minidump.mdmp(19.2) from control panel action center but I donot know how to use that :(

  Read the article

• How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

  - by piobyz

  I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

  Read the article

• How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

  - by piobyz

  I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

  Read the article

• How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

  - by piobyz

  I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

  Read the article

• Unknown user in terminal

  - by Giles B

  Im having a strange problem with the terminal in OS X. When I open the terminal the username at the command prompt is: unknown-04-0c-ce-e3-0d-c2: ~ I can't pinpoint when this first started or why unfortunately. I usually use iTerm for web development purposes but this also occurs in the normal OS X Terminal app. Any ideas/help would be really appreciated. Thanks Update: Thanks to @fayadfami and @aliasgar for the correct answers and steering me in the right direction. Also this forum post helped http://forums.macrumors.com/showthread.php?t=152407 The extract from the right post: Having run into the exact same issue myself, and having come across this thread while attempting to figure it out, I thought I'd post the answer. OS X is initially setting your hostname to what's set for your Computer Name in Sharing; however, if you're set up for DHCP and you match a current lease on your DHCP server (i.e., match the IP address of another recent user), OS X will then set your hostname to whatever the DHCP server currently has for that lease. This freaked me out incredibly at first, as I had just reformatted (having just purchased my first Mac and wanting to see how the installer worked) and knew I had not yet changed the Computer Name in Sharing -- yet my system hostname at the Terminal prompt was indeed changed to what I had previously set, pre-format. I grepped around, not finding the name anywhere save log entries; I thought either the format didn't actually properly wipe everything, or I was losing my mind. Finally I logged into my router (it's a Linksys WRT54GS running OpenWRT), and found the hostname in the current leases file. I then manually set my Mac's IP to something different, and volia! -- the hostname was back to what I expected. I hope this helps save someone from the same paranoia I went through.

  Read the article

• Error in Apache: /var/run/apache2 not found

  - by Julen

  This is more self-answered question but since it drove me crazy I would like to share with the community and maybe someone can tell me why it happened or what it caused. The thing is I wanted to install in my Ubuntu 10.4 machine a CGI app, one built in the samples that come with the gSOAP toolkit. My intention was to access those from ASP .NET machine. Regular Ubuntu does not come with Apache so I install it from Sypnatic. Pretty easy. I followed this How to Install Apache2 webserver with PHP,CGI and Perl Support in Ubuntu Server. Instead of apache.conf I tweaked httpd.conf since a college here used that file instead of the first to put his Apache running. Besides I was able to access his CGI from my ASP .NET but mysteriously I could not from mine, I was getting always "The request failed with HTTP status 503: Service Temporarily Unavailable". Checking Apache error.log I found these messages: No such file or directory: unable to connect to cgi daemon after multiple tries: /home/julen/htdocs/cgi-bin/calcserver And looking more carefully whenever I restarted Apache I got this other message No such file or directory: Couldn't bind unix domain socket /var/run/apache2/cgisock. cgid daemon failed to initialize I am pretty new with Ubuntu and I could not think that Apache and Synaptic made a mistake in the installation process of the server, but it is true that the /var/run/apache2 was missing whereas in my college's computer was not. I tried to find and "elegant" solution but I found a post from 2006 that had an slight reference to it. Finally I decided to create the folder myself (as root) and then everything worked fine. Hope this helps others if they encounter a similar problem. Still I have the doubt why the folders was not created in the first place. Best, Julen.

  Read the article

• Cisco Pix 515 ip addressing

  - by Rickard

  I have just gotten my hands on a Cisco Pix 515 (not 515E) with 3 interfaces, and are just about to start some labs. In my lab, I am using a real life scenario from an actual setup at work. As I have no access to the device at work, I am simply trying to replicate the scenario by trial and error. At work, we are given two IP addresses from the provider, which is 1-to-1 nated addresses. The addresses we are allowed to use are: 10.131.35.4-5/29 Now, we have 3 servers on a DMZ, 192.168.2.2-4/24 and 17 client computers on 192.168.1.100-117/24 aswell as some static addressed devices on 192.168.1.8-18/27 My question is, how would I best set up so that the machines on the DMZ get's translated to 10.131.35.4 and the machines on 192.168.1.* will be translated to 10.131.35.5 I don't expect or want anyone to give me a fully functional config, I may learn from it, but I'd prefer to just have some advices or maybe a guide on how to set it up. I hope someone can shed some light over my situation, have been looking through google but I guess I don't the searchwords I'm using isn't too good as I can't find any good clues. THank you very much! PS. Maybe I should add, I am not unfamiliar with the Cisco CLI, as I prefer using that before any gui's. So not really looking for any solutions for the ASDM. DS.

  Read the article

• MySQL Master-Master w/ multiple read slave cost effective setup in AWS

  - by Ross

  I've been evaluating Amazon Web Services RDS for MySQL and costing out potential scenarios involving a simple multi-AZ deployment read/write setup vs. a multi-AZ deployment mysql master (hot-standby) with additional read-only slaves. the issue I'm trying to cost-optimize includes their reserved instance vs on-demand instances. Situation 1: purchase reserved multi-az setup for Extra-large-hi-mem(17GB RAM) instance for $5200/yr and have my application query the master all the time. the problem is, if I don't need all the resources of the (17GB RAM) all the time and therefore, especially not a hot-standby, what alternatives for savings can a better topology create, like potentially situation 2 below: Situation 2: purchase reserved multi-az setup using smaller master instances than above for the master-master hot-standby to receive the writes only. Then create and load balance several read-only slaves off the master and add/remove and/or scale up/down the read slaves based on demand. This might only cost $1000 + the on-demand usage of the read slaves. My thinking is, if I have a variable read-intensive application load, with low write load, the single level topology in situation 1 means I'm paying for a lot of resources at the write level of topology when I don't need them there. My hope is that situation 2 can yield cost savings from smaller reserved instances on the master-master resource level allowing me to scale up and down and/or out on the read-level according to demand as needed. Does anyone see a downside to doing this or know of some reason this isn't possible with RDS? Any other thoughts or advice always welcome of course. Thanks in advance, R

  Read the article

• Assets not served - Apache Reverse proxy - Diaspora

  - by Matt

  I have succeeded in installing Diaspora* on my subdomain diaspora.mattaydin.com. I have VPS running CentOS 5.7 with Plesk installed. By means of an vhost.conf and vhost_ssl.conf file I, (with the help of another gentleman) have managed to reverse proxy the app. vhost.conf: ServerName diaspora.mattaydin.com ServerAlias *.diaspora.mattaydin.com <Directory /home/diaspora/diaspora/public> Options -Includes -ExecCGI </Directory> DocumentRoot /home/diaspora/diaspora/public RedirectPermanent / https://diaspora.mattaydin.com vhost_ssl.conf ServerName diaspora.mattaydin.com DocumentRoot /home/diaspora/diaspora/public RewriteEngine On RewriteCond %{DOCUMENT_ROOT}/%{REQUEST_FILENAME} !-f RewriteRule ^/(.*)$ balancer://upstream%{REQUEST_URI} [P,QSA,L] <Proxy balancer://upstream> BalancerMember http://127.0.0.1:3000/ </Proxy> ProxyRequests Off ProxyVia On ProxyPreserveHost On RequestHeader set X_FORWARDED_PROTO https <Proxy *> Order allow,deny Allow from all </Proxy> <Directory /home/diaspora/diaspora/public> Options -Includes -ExecCGI Allow from all AllowOverride all Options +Indexes </Directory> DocumentRoot /home/diaspora/diaspora/public Basically it's working. However, the only thing that's not working are the assets. The do not get loaded not the server, as seen on diaspora.mattaydin.com The error messages I get in the access_ssl.log are a lot of: 11/Dec/2012:19:04:05 +0100] "GET /robots.txt HTTP/1.1" 404 2811 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_2) AppleWebKit/536.26.17 (KHTML, like Gecko) Version/6.0.2 Safari/536.26.17" The error messages I get from diaspora's log file is: Started GET "//assets/branding/logo_large.png" for 77.250.99.193 at 2012-12-11 20:13:11 +0100 ActionController::RoutingError (No route matches [GET] "/assets/branding/logo_large.png"): lib/rack/chrome_frame.rb:39:in call' lib/unicorn_killer.rb:35:incall' Hope you guys can help me out. If you need anything else please let me know Thanks in advance, Matt

  Read the article

• Using UDF on a USB flash drive

  - by CesarB

  After failing to copy a file bigger than 4G to my 8G USB flash drive, I formatted it as ext3. While this is working fine for me so far, it will cause problems if I want to use it to copy files to someone which does not use Linux. I am thinking of formatting it as UDF instead, which I hope would allow it to be read (and possibly even written) on the three most popular operating systems (Windows, MacOS, and Linux), without having to install any extra drivers. However, from what I found on the web already, there seem to be several small gotchas related to which parameters are used to create the filesystem, which can reduce the compability (but most of the pages I found are about optical media, not USB flash drives). I would like to know: Which utility should I use to create the filesystem? (So far I have found mkudffs and genisoimage, and mkudffs seems the best option.) Which parameters should I use with the chosen utility for maximum compability? How compatible with the most common versions of these three operating systems UDF actually is? Is using UDF actually the best idea? Is there another filesystem which would have better compatibility, with no problematic restrictions like the FAT32 4G file size limit, and without having to install special drivers in every single computer which touches it?

  Read the article

• Apache2 Manage Server default

  - by Jaime E. Valdez

  I'm trying to setup two domains correctly. I have some issues I hope you can help me. Site one's conf: <VirtualHost myipaddress:80> ServerName www.domain1.com ServerAdmin [email protected] DocumentRoot /home/domain1/public_html </VirtualHost> My other domain conf is: <VirtualHost myipaddress:80> ServerName www.domain2.com ServerAlias *.domain2.com domain2.com ServerAdmin [email protected] DocumentRoot /home/domain2/public_html </VirtualHost> The default site is disabled. The problem is that when accessing "domain2.com" from my browser, it always redirects to "www.domain1.com". It only works when I excplicitly access "www.domain2.com". I have also other domains like "domain1.net", "domain1.info" pointing to my server but at this moment are not configured either setup on Apache yet I can access from browser and always accessing to "www.domain1.com". By the way is there any possible configuration over Apache to handle IP only, I mean if I type "http://myipaddress/" I get the "www.domain1.com"... Arrgh.

  Read the article

• ajax.googleapis.com stopping my Firefox

  - by Oscar Reyes

  Today for some strange reason, Firefox stops working properly because it is trying to fetch something from ajax.googleapis.com. Is there something I can do to avoid this? Safari and Chrome work just fine. I tried uninstalling Firebug and clearing the cache. The only thing that worked was disabling the JavaScript altogether. This seems to be the culprit link: http://ajax.googleapis.com/ajax/libs/jquery/1.3.2/jquery.min.js What can I do? EDIT I think I have found where the problem is. My proxy is serving one byte at a time the file, so firefox consume it at that peace. What I don't understand is why Safari and Chrome takes it right away. What I did last night was, leave the FF open all the night to give him change to load the file, my hope was that I got cached and the next time there was no need to go for it. Today in the morning, the page load successfully but the page was not cached, because the next request failed the same. Here's a video showing the problem:

  Read the article

• passing on command line options in bash

  - by bryan

  I have a question. I have a script, a kind of long script written in bash aprox. 370 lines. That has several functions and in those functions the user has to enter information which is then stored in files. ( This is suppose to represent a MySQL database, with the functions INSERT, UPDATE, SELECT, SELECT where x=y.) I created this myself in bash, now the only thing that rests me is that I need to be able to pass arguments on the command line to the script, that will do the same as the script does. I know that bash has positional parameters such as $1 $2 $3 $* $@ $0 ( refers to the name of the script) etc. I know how I can use these parameters in a simple if function. This is not enough for my script. I basicly need to do the same thing that the script does, but then from the command line. I have been struggling with this for a couple of days now and I cannot think of a way to get it to work. Maybe someone here can help me with this? If you want to have the script. That can be possible, but I don't think I can paste it in here... EDIT: Link to script, http://pastebin.com/Hd5VsDv2 Note, I am a beginner in bash scripting. EDIT: This is in reply to Answer 1. As I said I hope I can just replace the if [ "$1" = "one" ] ; then echo "found one" to if [ "$1" = "one" ] ; then echo SELECT where SELECT is the function I previously had in my script(above) http://pastebin.com/VFMkBL6g LINK to testing script

  Read the article

• SharePoint Business Connectivity Services (BCS) Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'

  - by g18c

  I am running SharePoint 2010 with SQL 2012, I am trying to get Business Connectivity Services (BCS) running but I am facing a double-hope authentication issue. Everytime I try to connect to the external BCS list created in SharePoint designer, I get the error Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. In the event viewer on the SQL server I see a login failure for an anonymous user from the SP server IP address. Background information below: I have enabled Kerberos under SharePoint Central admin. I have the following AD domain accounts: SP_Farm - main website pool SP_Services - for SharePoint services (including BCS) SQL_Engine - SQL database engine I then created the following with SetSPN: SetSPN -S http/intranet mydomain\SP_Farm SetSPN -S http/intranet.mydomain.local mydomain\SP_Farm SetSPN -S SPSvc/SPS mydomain\SP_Farm SetSPN -S MSSQLSvc/SQL1 mydomain\SQL_DatabaseEngine SetSPN -S MSSQLSvc/SQL1.mydomain.local mydomain\SQL_DatabaseEngine SetSPN -S MSSQLSvc/SQL1:1433 mydomain\SQL_DatabaseEngine SetSPN -S MSSQLSvc/SQL1.mydomain.local:1433 mydomain\SQL_DatabaseEngine I then delegated the AD accounts for any authentication protocol to the following: SP_Farm - SP_Farm (http service type, intranet) SP_Farm - SQL_DatabaseEngine (MSSQLSvc, sql1) SP_Service - SP_Service (SPSvc) SP_Service - SQL_DatabaseEngine (MSSQLSvc, sql1) I have also checked the WFE is being logged on to with Kerberos, with the WFE server event log showing event ID 4624 with Kerberos authentication, this is OK. The SQL is also showing connections authenticated as Kerberos from the WFE with the following query: Select s.session_id, s.login_name, s.host_name, c.auth_scheme from sys.dm_exec_connections c inner join sys.dm_exec_sessions s on c.session_id = s.session_id Despite the above, credentials are not passed from the client through the SharePoint server to the SQL server, only the anonymous account is used. I get the following error in the WFE server for 'BusinessData' ID 8080: Could not open connection using 'data source=sql1.mydomain.local;initial catalog=MSCRM;integrated security=SSPI;pooling=true;persist security info=false' in App Domain '/LM/W3SVC/1848937658/ROOT-1-129922939694071446'. The full exception text is: Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. If I set a username and password with the Secure Store Service and set the external list to use the impersonated credentials, the list works. Any ideas what I have missed and what can be tried next?

  Read the article

• Xp SP3 - Non-Functioning

  - by Josh

  Ok Here is a crazy problem, I have a HP dv6000 Laptop that can no longer hold a charge, so I hooked it up to my TV, bought a wireless mouse and keyboard and configured xp to run with the lid closed, It has medium to heavy usage mainly just streaming from sites like Netfilx, Hulu, ABC, etc. And playing movies I ripped of dvd. It ran fine for a while but recently it has been having some weird problems: Problem one: I used to use firefox but now when run it I can type but as soon as I click something it just shuts down, completely, I can't even close it unless I use taskmanager to do it. So I went and got google chrome which is better but still hit or miss, but never completely shuts down, I just can't click anything or type anything, or sometimes I just can't type anything or vice versa. Also when I open a new tab, and try to move back to my old one, it automatically closes the old tab when I click on it. Problem two: When using the internet I can't use any other application or anything windows (ie. Windows explorer) until I force quit all browsers with taskmanger. The reason I can't run anything is because I can't click on it. Problem three: When I try to play a movie (with vlc) Once it starts playing I can't click on anything, but I can use hotkeys, and once it stops everything is fine again. Well I hope somebody knows whats going on because I have no clue, If you need clarification or more info on something I would be happy to provide it...

  Read the article

< Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >