Search Results

Search found 6602 results on 265 pages for 'fedora 14'.

Page 177/265 | < Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >

• Proxmox drbd configuration split brain [on hold]

  - by AudioDan

  I am planning a proxmox HA configuration with two Dell R710 machines (dual 6 core processors in each) with enterprise level drive raid arrays. I would be using DRBD with a quorum disk on a third machine. I would dedicate two 1GB nics on each server to the DRBD communications. We would have approximately 12 to 14 Virtual Machines running on this pair of servers. The proxmox manual recommends creating two DRBD resources - one for the Virtual Machines that normally run on ServerA and one for the Virtual Machines that normally run on ServerB. This is because of the Primary/Primary state in which this configuration runs. If both servers have VMs talking to the same DRBD resource and a split brain situation occurs, there is potential for data corruption that must be resolved. While I understand it would take more effort to create new virtual machines, can anybody foresee any potential problems with running a separate DRBD resource for each VM instead? Does anyone have experience running a setup that way and has it worked well? It seems to me that would allow more flexibility in moving machines back and forth.

  Read the article

• Varnish gets in a restart loop and causes the system to lock up; how can I fix?

  - by chrism2671

  Here is an extract from the syslog. Mar 2 14:01:10 ip-10-226-34-17 varnishd[20204]: Child (20205) not responding to ping, killing it. Mar 2 14:01:16 ip-10-226-34-17 varnishd[20204]: Child (20205) not responding to ping, killing it. Mar 2 14:01:16 ip-10-226-34-17 varnishd[20204]: Child (20205) died signal=3 Mar 2 14:01:21 ip-10-226-34-17 varnishd[20204]: Child cleanup complete Mar 2 14:01:21 ip-10-226-34-17 varnishd[20204]: child (13224) Started Mar 2 14:01:21 ip-10-226-34-17 varnishd[20204]: Child (13224) said Closed fds: 4 5 6 10 11 13 14 Mar 2 14:01:21 ip-10-226-34-17 varnishd[20204]: Child (13224) said Child starts Mar 2 14:01:21 ip-10-226-34-17 varnishd[20204]: Child (13224) said managed to mmap 536870912 bytes of 536870912 Mar 2 14:01:21 ip-10-226-34-17 varnishd[20204]: Child (13224) said Ready Mar 2 14:01:35 ip-10-226-34-17 varnishd[20204]: Child (13224) not responding to ping, killing it. Mar 2 14:02:10 ip-10-226-34-17 last message repeated 7 times Mar 2 14:03:15 ip-10-226-34-17 last message repeated 13 times Mar 2 14:03:20 ip-10-226-34-17 varnishd[20204]: Child (13224) not responding to ping, killing it. Mar 2 14:05:53 ip-10-226-34-17 varnishd[20204]: Child (13224) not responding to ping, killing it. Mar 2 14:05:53 ip-10-226-34-17 varnishd[20204]: Child (13224) not responding to ping, killing it. Mar 2 14:05:53 ip-10-226-34-17 varnishd[20204]: Child (13224) died signal=3 Mar 2 14:05:53 ip-10-226-34-17 varnishd[20204]: Child cleanup complete Mar 2 14:05:53 ip-10-226-34-17 varnishd[20204]: child (13288) Started I'm not expecting a solution here but any help just to decode what each line is doing would be very instructive. Many thanks!

  Read the article

• Percona-server time out on /etc/init.d/mysql start

  - by geekmenot

  Every time I start mysql, using /etc/init.d/mysql start or service mysql start, it always times out. * Starting MySQL (Percona Server) database server mysqld [fail] However, I can get into mysql. Just wanted to know if there is a problem with the install because it happens all the time, not a one off error. mysql-error.log shows: 121214 11:25:56 mysqld_safe Starting mysqld daemon with databases from /data/mysql/ 121214 11:25:56 [Note] Plugin 'FEDERATED' is disabled. 121214 11:25:56 InnoDB: The InnoDB memory heap is disabled 121214 11:25:56 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121214 11:25:56 InnoDB: Compressed tables use zlib 1.2.3 121214 11:25:56 InnoDB: Using Linux native AIO 121214 11:25:56 InnoDB: Initializing buffer pool, size = 14.0G 121214 11:25:58 InnoDB: Completed initialization of buffer pool 121214 11:26:01 InnoDB: Waiting for the background threads to start 121214 11:26:02 Percona XtraDB (http://www.percona.com) 1.1.8-rel29.2 started; log sequence number 9333955393950 121214 11:26:02 [Note] Server hostname (bind-address): '0.0.0.0'; port: 3306 121214 11:26:02 [Note] - '0.0.0.0' resolves to '0.0.0.0'; 121214 11:26:02 [Note] Server socket created on IP: '0.0.0.0'. 121214 11:26:02 [Note] Slave SQL thread initialized, starting replication in log 'mysql-bin.005163' at position 624540946, relay log '/data/mysql/mysql-relay-bin.000043' position: 624541092 121214 11:26:02 [Note] Slave I/O thread: connected to master '[email protected]:3306',replication started in log 'mysql-bin.005180' at position 823447620 121214 11:26:02 [Note] Event Scheduler: Loaded 0 events 121214 11:26:02 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.5.28-29.2-log' socket: '/data/mysql/mysql.sock' port: 3306 Percona Server (GPL), Release 29.2

  Read the article

• Single m0n0wall - Two LAN Subnets - How To Setup

  - by SnAzBaZ

  I have two LAN subnets that I need to link together they are 192.168.4.0/24 and 192.168.5.0/24 There is a m0n0wall running on 192.168.4.1. It's LAN connection goes out to our network switch, and it's WAN port goes out to our ADSL modem. WAN is connected via PPPoE. The 192.168.4.0 subnet contains all of our office workstations. The 192.168.5.0 subnet contains development servers and test machines that need to obtain internet access and be "managed" by computers on the 192.168.4.0 subnet, but need to be on their own subnet as well. I have a Draytek 2820N configured on 192.168.5.1 with it's WAN2 port configured as 192.168.4.25 and a default gateway of 192.168.4.1. Machines on the 5.0 subnet can connect to the internet via the m0n0wall just fine. I configured a static route on the m0n0wall LAN interface, Network 192.168.5.0/24 and Gateway 192.168.4.25. Machines on the 5.0 subnet can ping machines on the 4.0 network but the reverse does not work. I configured a new firewall rule on the m0n0wall that allows any traffic on the LAN interface with a source IP of 192.168.4.25 to be allowed. The DrayTek firewall is currently configured to pass all traffic regardless. When I try to ping a machine in the 5.0 subnet from 4.0 I see this in my m0n0wall log: BLOCK 14:45:27.888157 LAN 192.168.4.25 192.168.4.37, type echoreply/0 ICMP So the reply is being sent from the 5.0 subnet but is not being allowed to reach my workstation because the firewall is blocking it. Why is the firewall blocking it ? I hope the explanation of my network is clear, please ask if you require further clarification. Thank you.

  Read the article

• File permission woes on an Ubuntu ec2 instance

  - by Pardoner

  I've set up an amazon ec2 instance and I'm have some file permission issues. I've created myself a new user and added myself to the following groups: adm:x:4:me,ubuntu sudo:x:27:me www-data:x:33:me,www-data ssh:x:108:me admin:x:111:me ubuntu:x:1000:www-data,me me:x:1001:me but when I cd /var/www I can't do simple commands without doing sudo. So I chown -R www-data:www-data /var/www to ensure that I'm in the owning group but I still have to type sudo for everything. If I sudo su www-data it works fine. Since I'm in the www-data group shouldn't I have the same privilages as www-data? One strange thing I'm noticing is that when I ls -l it list the owner but not the group names. Could this possibly be part of the issue? Is is posible for a directory to not be part of a group? drwxr-xr-x 4 www-data 4.0K Oct 24 16:39 . drwxr-xr-x 14 root 4.0K Oct 10 16:58 .. drwxrwxr-x 9 www-data 4.0K Oct 23 04:03 admin.mywebsite.com drwxrwxr-x 2 www-data 4.0K Oct 4 00:29 mywebsite.com drwxrwxr-x 9 www-data 4.0K Oct 23 04:03 staging.mywebsite.com Edit : It appears I had some alias messing with my ls command. By calling \ls -l I can see that all my files are in the correct group.

  Read the article

• Backup Exec tape rotation guidelines

  - by HannesFostie

  Hi We use Backup Exec to take care of our backups for our data server, exchange server, and one more set of systems. Each of these 3 is being done on a separate "set" of tapes. Our goal is to be able to roll back a full 2 weeks, with 1 full backup each weekend and differential/incremental backups in between (the difference between the two in our case isn't very big, because the employees mostly use a very similar set of files throughout the week). While playing around with the settings on how to achieve this, we set the time for BE to keep the full backup to 14 days, but because we have too much data this would require manual intervention each time to erase a certain tape and use that. What I would like to know is what kind of guidelines, tricks, tips and general "stuff to think about" you keep in mind when designing your backup schedule. The type of backups (full/diff/incr) isn't of that much importance in our case as it's more or less set in stone. Made this community wiki as it's not a very specific question. Thanks in advance!

  Read the article

• web.config file changings guide

  - by Student

  Hi experts how are you all? i am student, and learning asp.net c# visual studio 2010 with using sql server 2005. I have developed a website which has database. I developed this website with self studies taking help from internet. the website is completed and working perfectly in my computer. I have hosting server and domain name registered already. the problem is when I upload my website it doesn't work there the following error displays: Server Error in '/' Application. Configuration Error Description: An error occurred during the processing of a configuration file required to service this request. Please review the specific error details below and modify your configuration file appropriately. Parser Error Message: Unrecognized attribute 'targetFramework'. Note that attribute names are case-sensitive. Source Error: Line 11: <system.web> Line 12: <customErrors mode="Off" /> Line 13: <compilation debug="false" targetFramework="4.0"/> Line 14: </system.web> Line 15: </configuration> Source File: C:\Inetpub\vhosts\urdureport.com\httpdocs\web.config Line: 13 Version Information: Microsoft .NET Framework Version:2.0.50727.5472; ASP.NET Version:2.0.50727.5474 I don't know what should I do to get it work on hosting server please help me in this regard that what should I do with this. Thank you in advance

  Read the article

• mysql thread count

  - by Ryan M.

  We have a web application that uses apache and mysql. Generally (according to Munin) our MySQL thread count sits between 2 and 4 at all times. The other day, our server almost came to a halt. HTTP requests were slow or wouldn't go through at all, SSH would work, but would take 30+ seconds to register keystrokes, etc.. So we pull up Munin and the only thing that's out of normal boundaries is the Mysql thread count. CPU usage was under 1%, load was under 1.0, plenty of available RAM. As mentioned before, the thread count floats around 2 to 4. At the time of our slow downs it had spiked to 14. So I start poking around the Internet and I see that in most cases, you'll start to see a higher thread count when you start running into slow queries. If I understand it correctly, the request comes in that takes a while to process, in the mean time other requests are coming in, so a new thread will be created to work on the request (yes?). But at the time of the slow down, we had 0 slow queries. My question is: What else can cause mysql to create additional threads. And would this sudden spike in threads possibly cause the server to slow down? To fix the issue, we restarted apache and everything went back to it's beautiful, normal self. Considering the the Server Vitals (CPU, RAM, Network, etc) were all ideal, and the thread count was the only thing out of place, this seems like the most logical thing to pursue as the possible cause. If it matters, we're on Mysql 5.1.40. Server is FreeBSD 7.2 and the server in question is inside a jail.

  Read the article

• Freebsd jail for an small company - checklist - what shouldn't forget

  - by cajwine

  Looking for an checklist for an "small company freebsd/jail server". Having pretty common starting point: FreeBSD jail (remote/headless) for the company: public web, email, ftp server, and private (maybe in the future partially public) wiki (foswiki) 4 physical persons, (6 email addresses) + one admin - others will never use ssh) have already done usual hardening on the host side (like pf, sshguard etc). my major components are: dovecot, exim, apache22, proftpd, perl5.14. Looking for an checklist, what I shouldn't forget. My plan: openssl self-signed certificates for exim, dovecot and proftpd (wildcard keys) openssl self-signed certificate for apache (later will go for "trusted-signed" key) My questions are: is is an "good practice" having one pair of wildcard SSL-certificates for many programs? (exim, dovecot, proftpd) - or should I generate one key for each service? should I add all 4 persons as standard (unix) users, or I should go with virtual users? Asking because: have only small count of users, and it is more simple to configure everything (exim, dovecot) for local users ($HOME/Maildir), plus ability to set $HOME/.forward/vacation and etc. is here some (special) things what I should consider? (e.g. maybe, in the future we want setup our own webmail - will make this any difference?) any other recommendation? Thank you, hoping that this question fit into the http://serverfault.com/faq under the: Server and Business Workstation operating systems, hardware, software Operations, maintenance, and monitoring Looking for an checklist, but please explain why you're recommending it. See Good Subjective, Bad Subjective. related: What's your suggested mail server configuration for a FreeBSD server?

  Read the article

• Under what conditions will sendmail try to immediately resend a message instead of waiting for the standard requeue interval?

  - by Mike B

  CentOS 5.8 | Sendmail 8.14.4 I used to think that if SendMail experienced a temporary (400-class) error during delivery, it would place the message in a deferred queue (e.g. /var/spool/mqueue) and retry an hour later. For the most part, that appears to be the case. But every now and then, I'll notice log entries like this (email/domains renamed to protect the innocent :-) ) : Dec 5 01:43:03 foobox-out sendmail [11078]: qBE3l7js123022: to=<[email protected]>, delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=124588, relay=exbox.foo.com. [10.10.10.10], dsn=4.0.0, stat=Deferred: 421 4.3.2 The maximum number of concurrent connections has exceeded a limit, closing transmission channel Dec 5 01:53:34 foobox-out sendmail [12763]: qBE3l7js123022: to=<[email protected]>, delay=00:10:31, xdelay=00:00:00, mailer=relay, pri=214588, relay=exbox.foo.com., dsn=4.0.0, stat=Deferred: 452 4.3.1 Insufficient system resources Dec 5 02:53:35 foobox-out sendmail [23255]: qBE3l7js123022: to=<[email protected]>, delay=01:10:32, xdelay=00:00:01, mailer=relay, pri=304588, relay=exbox.foo.com. [10.10.10.10], dsn=2.0.0, stat=Sent (<[email protected]> Queued mail for delivery) Why did Sendmail try again just 10 minutes after the first attempt and then wait another hour before trying again? If this is expected behavior, what scenarios will cause this faster requeue interval to occur?

  Read the article

• In a Shell scripts, check version of installed package, make a decision based on output

  - by DJDarkViper

  Looking to write a cross distro / cross version shell script that makes sure a forced version of PHP is installed Example: Ubuntu 12.04 has 5.3, Ubuntu 13.10 has 5.5, Debian 7 has 5.4 I need this script, when run on a distro that has an old version of PHP, to update the repo to point to a package for 5.4, and if the distro has too new of a version, can downgrade to 5.4 appropriately. Im still not entirely comprehensive of Shell/Terminals technical limit of what you can do with it, but ill be perfectly frank that im still not totally used to existing tools The best I can think at the moment is: php -v | grep "PHP 5" but that returns a bunch of potentially changeable granular characters (PHP 5.4.4-14+deb7u5 (cli) (built: Oct 3 2013 09:24:58) ). Im not sure what to pipe to after this to extract out the characters im interested in Im not sure if im being totally clear, im not sure how to ask this.. Basically, in an automated shell script for Linux distros, how do I extract the PHP version (and just the PHP version number preferably) and make a decision based on that output EDIT This line ended up doing pretty dang good php -v | grep "PHP 5" | sed 's/.*PHP \([^-]*\).*/\1/' | cut -c 1-3 Bit long in the tooth, but gives me "5.3", "5.4", and "5.5" which is exactly what I need to work with

  Read the article

• esx5 debian VM vlan setup

  - by Kstro21

  i have a server with ESX5, have a switch with about 20 vlans, this is how setup the trunk port interface GigabitEthernet0/1/1 description ToOper port link-type trunk undo port trunk allow-pass vlan 1 port trunk allow-pass vlan 2 to 14 stp disable ntdp enable ndp enable bpdu enable then, i created a standar switch(sw1) using the vSphere Client, the VLAN ID is set to All (4095), i also created a VM with Debian 6, with a NIC connected to sw1, now, i want to configure this NIC for a selected group of vlans auto vlan10 iface vlan10 inet static address 11.10.1.0 netmask 255.255.255.224 mtu 1500 vlan_raw_device eth0 auto vlan14 iface vlan14 inet static address 11.10.1.65 netmask 255.255.255.248 mtu 1500 vlan_raw_device eth0 so, when i restart the network using /etc/init.d/networking restart, i got this error Reconfiguring network interfaces...SIOCSIFADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFNETMASK: No such device SIOCSIFBRDADDR: No such device vlan14: ERROR while getting interface flags: No such device SIOCSIFMTU: No such device vlan14: ERROR while getting interface flags: No such device Failed to bring up vlan14. done. this is just part of the error, so, my questions is: is this possible?, i mean, what i'm trying to achieve using ESX Virtual Machines, VLANS, etc is this a Debian problem? can be solved? i've read about a file named z25_persistent-net.rules in Debian but it doesn't exist in my installation. in the In the vSphere Networking for ESX5 guide, you can read: If you enter 0 or leave the option blank, the port group can see only untagged (non-VLAN) traffic. If you enter 4095, the port group can see traffic on any VLAN while leaving the VLAN tags intact. So, in theory, it should work, right? Hope you can help me up with this one Thanks

  Read the article

• High fan speed with no reason

  - by Klaus

  For a few weeks, the fans of my Lenovo B590 laptop, running on Xubuntu 14, turn to high speed a few minutes after it is turned on. The fans won't speed down until I turn the computer off. This is quite strange, since This didn't happen before The temperatures are quite low (are they ?) $sensors Adapter: Virtual device temp1: +36.0°C (crit = +88.0°C) temp2: +30.0°C (crit = +126.0°C) coretemp-isa-0000 Adapter: ISA adapter Physical id 0: +37.0°C (high = +72.0°C, crit = +90.0°C) Core 0: +34.0°C (high = +72.0°C, crit = +90.0°C) Core 1: +31.0°C (high = +72.0°C, crit = +90.0°C) thinkpad-isa-0000 Adapter: ISA adapter fan1: 0 RPM pkg-temp-0-virtual-0 Adapter: Virtual device temp1: +37.0°C $sudo hddtemp /dev/sda /dev/sda: ST500LT012-9WS142: 33°C The computer is under low load: top - 08:30:15 up 16 min, 2 users, load average: 0.28, 0.23, 0.23 Tasks: 197 total, 1 running, 196 sleeping, 0 stopped, 0 zombie %Cpu(s): 0.8 us, 0.5 sy, 0.0 ni, 98.7 id, 0.0 wa, 0.0 hi, 0.0 si, 0.0 st KiB Mem: 3607944 total, 1973956 used, 1633988 free, 99660 buffers KiB Swap: 3744764 total, 0 used, 3744764 free. 789936 cached Mem The BIOS is up to date (and there are no fan settings in it) The fan is clean and dust-free Why would the BIOS turn the fans to high speed where there seem to be no reason for that ? It seems that we cannot control the fan manually with this model, so I guess the only solution is to understand why this happens.

  Read the article

• Can't access WordPress blog after host changed IP address of server

  - by John

  My host changed servers and all websites now have a new IP address. I have the same domain name and I assume the host runs the same nameservers, though my host and domain name provider are different. Notes: I never entered a Name or description under General/Settings for my blog. I left them both blank. That is when I could log into it. The wp-config file, has localhost entered rather than a specific IP. Again this has always been the case and my host never advised otherwise. I can get into cPanel by simply putting the newly advised IP in front of /Cpanel. However, I can not reach the admin panel of my WordPress blog (version 2.8.2). I had been loggin into it via http://xx.xx.xxx.xx/~example/blog/wp-login.php. My host suggested to simply insert the new IP in place of the old one. I still get the error message: 404 Not Found The server can not find the requested page: Apache/2.0.63 (Unix) mod_ssl/2.0.63 OpenSSL/0.9.8e-fips-rhel5 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 PHP/5.2.12 Server at 74.50.108.14 Port 80 I followed some tips on a question on Stack Overflow of a similar nature. I have logged into phpMyAdmin and found the wp-options table and searched for SELECT * FROM `wp_options` WHERE `option_name` IN ('siteurl', 'home') Only option ID 39 came up and the results are: Home has optionvalue http://example.org siteurl has optionvalue http://example.org/blog Both of which appear correct. Is there any part of the MySQL tables where I can change an actual IP address? Or is there something else you can advise?

  Read the article

• On linux, what does it mean when a directory has size 0 instead of 4096?

  - by kdt

  Here's a strange thing I haven't seen before -- a directory whose size is reported by ls as 0 instead of 4096, and I can't create any files within it. # ls -ld lib home drwxr-xr-x. 2 root root 0 Feb 7 03:10 home <-- it has zero size dr-xr-xr-x. 11 root root 4096 Feb 4 09:28 lib # touch home/foo touch: cannot touch `home/foo': No such file or directory <-- and I can't create files in it # rm home rm: cannot remove `home': Is a directory <-- look, it really is a dir So what does it mean for a directory to have size 0 instead of 4096? Filesystem is ext4 on fedora core 14. The output of mount is: /dev/mapper/vg_dev-lv_root on / type ext4 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) tmpfs on /dev/shm type tmpfs (rw,rootcontext="system_u:object_r:tmpfs_t:s0") /dev/vda1 on /boot type ext4 (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) sunrpc on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw) Output of du -s /home: 0 /home Output of stat /home: File: `/home' Size: 0 Blocks: 0 IO Block: 1024 directory Device: 15h/21d Inode: 34913 Links: 2 Access: (0755/drwxr-xr-x) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2011-02-07 03:45:46.188995765 -0800 Modify: 2011-02-07 03:11:59.980995019 -0800 Change: 2011-02-06 07:58:45.874995002 -0800

  Read the article

• No sound out of headphone port on laptop

  - by Thanatos

  I cannot get sound out of the headphone port on a laptop. Headphones are plugged in, and sound comes out of the internal speakers. Windows behaves normally (sound switches to headphones when headphones are inserted). It did work in Linux at one point, but something changed, we're just not sure what. Rebooting doesn't fix. This appears to occur whether or not PulseAudio is running. Things I've tried: Rebooting. No effect. Booting into Windows. It works properly, so probably not a hardware issue. All of alsamixer. My only controls are this: "Master" Volume bar & mutable, unmuted. Controls volume. "PCM" Volume bar only. 100%. "S/PDIF" Mutable only, currently muted, has no effect. "S/PDIF" Default PCM", Mutable only, currently unmuted, has no effect. Killing PulseAudio. No effect. (It also won't stay dead! Something appears to be restarting it, and I can't tell what, but it is annoying as fuck.) alsactl init 0, no effect. sudo rm -f /var/lib/alsa/asound.state, no effect. General system info: Ubuntu 10.04 LTS Toshiba Satellite T135D-S1324 lspci says I have: 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller Some edits: Yes, the headphones are in all the way. This works in Windows: You plug headphones in, the internal speakers stop making noise, and noise comes out the head phones. Windows says I only have two sound cards: the HDMI port (which I don't care about) and the "sound card", which it claims is a "Conexant Pebble High Definition SmartAudio" In Windows, both the internal speakers and the headphone jack show up as one soundcard, which in my experience, is typical. (This is a laptop)

  Read the article

• ssh from 1 ubuntu box to another ubuntu box

  - by michael

  Hi, I have 2 ubuntu boxes in a WiFi network. Below is the 'ifconfig' of my destination machine. But in my source machine, I tried 'ssh 192.168.1.2' I get connection refused. $ ifconfig eth0 Link encap:Ethernet HWaddr c8:0a:a9:4d:d6:6a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:35 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4508 errors:0 dropped:0 overruns:0 frame:0 TX packets:4508 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:330441 (330.4 KB) TX bytes:330441 (330.4 KB) wlan0 Link encap:Ethernet HWaddr 00:23:14:32:e8:dc inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:14ff:fe32:e8dc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:319828 errors:0 dropped:0 overruns:0 frame:0 TX packets:618371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:30642011 (30.6 MB) TX bytes:921522542 (921.5 MB) How to set up so that I can ssh from 1 box to another?

  Read the article

• Why is ssh agent forwarding not working?

  - by J. Pablo Fernández

  In my own computer, running MacOSX, I have this in ~/.ssh/config Host * ForwardAgent yes Host b1 ForwardAgent yes b1 is a virtual machine running Ubuntu 12.04. I ssh to it like this: ssh pupeno@b1 and I get logged in without being asked for a password because I already copied my public key. Due to forwarding, I should be able to ssh to pupeno@b1 from b1 and it should work, without asking me for a password, but it doesn't. It asks me for a password. What am I missing? This is the verbose output of the second ssh: pupeno@b1:~$ ssh -v pupeno@b1 OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug1: Connecting to b1 [127.0.1.1] port 22. debug1: Connection established. debug1: identity file /home/pupeno/.ssh/id_rsa type -1 debug1: identity file /home/pupeno/.ssh/id_rsa-cert type -1 debug1: identity file /home/pupeno/.ssh/id_dsa type -1 debug1: identity file /home/pupeno/.ssh/id_dsa-cert type -1 debug1: identity file /home/pupeno/.ssh/id_ecdsa type -1 debug1: identity file /home/pupeno/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9p1 Debian-5ubuntu1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: sending SSH2_MSG_KEX_ECDH_INIT debug1: expecting SSH2_MSG_KEX_ECDH_REPLY debug1: Server host key: ECDSA 35:c0:7f:24:43:06:df:a0:bc:a7:34:4b:da:ff:66:eb debug1: Host 'b1' is known and matches the ECDSA host key. debug1: Found key in /home/pupeno/.ssh/known_hosts:1 debug1: ssh_ecdsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: /home/pupeno/.ssh/id_rsa debug1: Trying private key: /home/pupeno/.ssh/id_dsa debug1: Trying private key: /home/pupeno/.ssh/id_ecdsa debug1: Next authentication method: password pupeno@b1's password:

  Read the article

• Wake for Network Access Apache servr in OS X 10.8, followup

  - by Gary

  Sorry, I can't seem to post this response within the same thread. Thank you both (Zoredache and Gordon) for your answer. But the fix seems temporary. I entered the command you suggested, and it seemed to work: ...smith$ Registering Service ApacheNoDoz._http._tcp.local port 80 DATE: ---Fri 14 Sep 2012--- 12:04:15.813 ...STARTING... 12:04:16.566 Got a reply for service ApacheNoDoz._http._tcp.local.: Name now registered and active So, I checked for it on my G5: Browsing for _http._tcp Timestamp.....A/R Flags if Domain......Service Type...Instance Name (lots of Bonjour printers omitted)... 12:07:38.370..Add.....2..4 local.......... _http._tcp.........ApacheNoDoz 12:07:45.921..Rmv.....0..4 local..........._http._tcp.........ApacheNoDoz So, it was running at 12:07:38, at which time the host was asleep. But, shortly after, the activity seems to have been removed. I don't know why. Does this mean that I can never let the cpu sleep, or is there something else I have to set? Thanks, again.

  Read the article

• Adding file to /etc/cron.d doesn't make it run (ubuntu 10.04)

  - by tom

  If I scp a cron file into /etc/cron.d it doesn't run unless I edit the file and change the command. Then crond seems to pick up the cron file. How can I make cron reload its cron files in ubuntu 10.04? 'touch'ing the file doesn't work nor does 'restart cron' or 'reload cron'. My cron file is set to run every minute and logs to a file. Nothing ends up in the log file until I edit the command, and there's no entry for it in /var/log/syslog I'm stumped. Here's my cron file saved to /etc/cron.d/runscript # Runs the script every minute. This is safe because it will exit with success if it's already running * * * * * www-data if [ -f /usr/local/bin/thing ]; then exec /usr/bin/php /usr/local/bin/thing mode:prod -a 14 -d >> /var/log/thing/mything.log 2>&1; else echo `date +'[%D %T]'` "Thing not deployed. Command not run\n" >> /var/log/thing/mything.log; fi &

  Read the article

• Glassfish v3 failure when startup. "Cannot allocate memory "

  - by Shisoft

  It is clear in this Question Fail to start Glassfish 3.1: java.io.IOException: error=12, Cannot allocate memory But in my case,I have a 512M memory Ubuntu 10.04 vps.It seems that I don't need to change any configure.But when start the server,I got this exception VM failed to start: java.io.IOException: Cannot run program "/usr/lib/jvm/java-6-sun-1.6.0.22/bin/java" (in directory "/home/glassfish/glassfish/domains/domain1/config"): java.io.IOException: error=12, Cannot allocate memory So,I set <jvm-options>-Xmx512</jvm-options> to <jvm-options>-Xmx400</jvm-options> The exception remains.What did I do something wrong? result of free -m total used free shared buffers cached Mem: 512 43 468 0 0 0 -/+ buffers/cache: 43 468 Swap: 0 0 0 result of cat /proc/user_beancounters Version: 2.5 uid resource held maxheld barrier limit failcnt 146049: kmemsize 2670652 5385253 51200000 51200000 0 lockedpages 0 8 2048 2048 0 privvmpages 11134 134522 131200 262200 4 shmpages 648 1352 128000 128000 0 dummy 0 0 0 0 0 numproc 12 73 500 500 0 physpages 6519 28162 0 200000000 0 vmguarpages 0 0 512000 512000 0 oomguarpages 6527 28169 512000 512000 0 numtcpsock 4 14 4096 4096 0 numflock 0 5 2048 2048 0 numpty 1 2 32 32 0 numsiginfo 0 3 1024 1024 0 tcpsndbuf 159600 265744 20480000 20480000 0 tcprcvbuf 65536 3590352 20480000 20480000 0 othersockbuf 44232 90640 20480000 20480000 0 dgramrcvbuf 0 12848 10240000 10240000 0 numothersock 22 31 2048 2048 0 dcachesize 0 0 10240000 10240000 0 numfile 1002 1474 50000 50000 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 24 24 2048 2048 0 Thanks

  Read the article

• Firefox v15.0 about:newtab inaccessible via the back button

  - by Willem

  As of this morning I upgraded my Firefox to version 15.0. Or well, it did it for me. That's when my issue began. I've configured Firefox so that when I open up a new tab via Ctrl-T that it loads the about:newtab page which was released in version 14.x(?). I use this functionality extensively. I visit a page from the about:newtab page, read it, press the back button and pick another frequent website from the display I want to visit. However as of v15.0 the latter part is no longer functioning, after visiting a website from the about:newtab page the back button will not let me go back to the about:newtab page. Firefox acts as if that history entry was never there. I've tried searching the release notes to see if this change was intentional or a reported bug, but I have not found anything related so far. Is there anyway to (re)configure the new Firefox v15.0 to let me access the about:newtab page via a tab's history? EDIT: It appears that this only affects the initial 'visit' to the about:newtab page when opening a new tab, manually visiting about:newtab will register it as a history entry and allow it to be navigated to via the back and forward buttons. So I guess this changes my question to 'How can I make Firefox 15.0 treat the inital page from a newtab as a history entry'.

  Read the article

• logrotate deletes all maillogs older than one day

  - by shadyabhi

  I see only two files maillog and maillog.1 in /var/log. grepping for maillog in logrotate.d directory gives three files that have a mention of maillog. syslog /var/log/messages /var/log/secure /var/log/maillog /var/log/spooler /var/log/boot.log /var/log/cron { #/var/log/messages /var/log/secure /var/log/spooler /var/log/boot.log /var/log/cron { daily sharedscripts postrotate /bin/kill -HUP `cat /var/run/syslogd.pid 2> /dev/null` 2> /dev/null || true /bin/kill -HUP `cat /var/run/rsyslogd.pid 2> /dev/null` 2> /dev/null || true endscript } syslog-ng /var/log/messages /var/log/secure /var/log/maillog /var/log/spooler /var/log/boot.log /var/log/cron /var/log/kern.log /var/log/kern { sharedscripts postrotate /bin/kill -HUP `cat /var/run/syslogd.pid 2> /dev/null` 2> /dev/null || true /bin/kill -HUP `cat /var/run/rsyslogd.pid 2> /dev/null` 2> /dev/null || true endscript } and maillog. /var/log/maillog { daily compress # rotate 365 rotate 14 sharedscripts postrotate /bin/kill -HUP `cat /var/run/syslogd.pid 2> /dev/null` 2> /dev/null || true /bin/kill -HUP `cat /var/run/rsyslogd.pid 2> /dev/null` 2> /dev/null || true endscript } I am new to logrotate so may be I am missing something obvious. What can be the issue? The setup was already done when I started managing the server so I don't also know as do why do I have 3 mentions for maillog in logrotate.

  Read the article

• copy large LVM volume(14TB) from one server to another

  - by bruce

  recently,I have to copy a very large LVM volume()rom server A to server B. Below is the filesystem of server A and server B - server A [root@AVDVD-Filer ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_avdvdfiler-lv_root 16T 14T 1.5T 91% / tmpfs 3.0G 0 3.0G 0% /dev/shm /dev/cciss/c0d0p1 194M 23M 162M 13% /boot /dev/mapper/vg_avdvdfiler-test 2.3T 201M 2.1T 1% /test /dev/sr0 3.3G 3.3G 0 100% /mnt server B [root@localhost ~]# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup-LogVol00 20G 2.5G 16G 14% / tmpfs 3.0G 0 3.0G 0% /dev/shm /dev/cciss/c0d0p1 194M 23M 162M 13% /boot /dev/mapper/VolGroup00-LogVol00 16T 133M 15T 1% /xiangao/lv1 /dev/mapper/VolGroup00-LogVol01 4.7T 190M 4.5T 1% /xiangao/lv2 I want to copy LVM volume /dev/mapper/vg_avdvdfiler-lv_root on server A to LVM volume /dev/mapper/VolGroup00-LogVol00 on server B . The server A and server B is in the same IP segment. IN the LVM volume on server A , there is all average 500M avi wmv mp4 etc. I tried mount /dev/mapper/vg_avdvdfiler-lv_root on server A to server B through NFS , then use cp command copy. It is clear I faild . Because the LVM volume is too big , I do not have good idea . I hope a good solution here. I'm a chinese, my english is very pool. sorry thanks everyone!

  Read the article

• 3 simple questions about file permissions

  - by Camran

  1- Wonder, is this a good setup of permissions in the /var directory? drwxr-xr-x 2 root root 4096 2010-05-30 03:34 backups drwxr-xr-x 7 root root 4096 2010-05-29 17:55 cache drwxr-xr-x 29 root root 4096 2010-05-29 17:55 lib drwxrwsr-x 2 root staff 4096 2009-07-14 04:36 local drwxrwxrwt 3 root root 60 2010-06-02 03:34 lock drwxr-xr-x 9 root root 4096 2010-06-02 03:34 log drwxrwsr-x 2 root man 4096 2009-09-20 20:36 mail drwxr-xr-x 2 root root 4096 2009-09-20 20:36 opt drwxrwxrwt 12 root root 420 2010-06-02 12:12 run drwxr-xr-x 4 root root 4096 2009-09-20 20:37 spool drwxrwxrwt 2 root root 4096 2009-07-14 04:36 tmp drwxr-xr-x 14 user root 4096 2010-05-30 22:21 www 2- Could you give me a brief explanation of the columns above? First one is which permissions they have. Second is a nr. Third and fourth says "root root" for example. fifth is another nr (4096 for example). and the others are obvious. 3- Could you give me a brief explanation of the folders above? Especially the "lock" and "tmp" folders. Lock contains an apache2 folder which seems empty. Thanks

  Read the article

< Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >