Search Results

Search found 5067 results on 203 pages for 'squid deb proxy'.

Page 178/203 | < Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >

• Cisco 3560+ipservices -- IGMP snooping issue with TTL=1

  - by Jander

  I've got a C3560 with Enhanced (IPSERVICES) image, routing multicast between its VLANs with no external multicast router. It's serving a test environment where developers may generate multicast traffic on arbitrary addresses. Everything is working fine except when someone sends out multicast traffic with TTL=1, in which case the multicast packet suppression fails and the traffic is broadcast to all members of the VLAN. It looks to me like because the TTL is 1, the multicast routing subsystem doesn't see the packets, so it doesn't create a mroute table entry. If I send out packets with TTL=2 briefly, then switch to TTL=1 packets, they are filtered correctly until the mroute entry expires. My question: is there some trick to getting the switch to filter the TTL=1 packets, or am I out of luck? Below are the relevant parts of the config, with a representative VLAN interface. I can provide more info as needed. #show run ... ip routing ip multicast-routing distributed no ip igmp snooping report-suppression ! interface Vlan44 ip address 172.23.44.1 255.255.255.0 no ip proxy-arp ip pim passive ... #show ip igmp snooping vlan 44 Global IGMP Snooping configuration: ------------------------------------------- IGMP snooping : Enabled IGMPv3 snooping (minimal) : Enabled Report suppression : Disabled TCN solicit query : Disabled TCN flood query count : 2 Robustness variable : 2 Last member query count : 2 Last member query interval : 1000 Vlan 44: -------- IGMP snooping : Enabled IGMPv2 immediate leave : Disabled Multicast router learning mode : pim-dvmrp CGMP interoperability mode : IGMP_ONLY Robustness variable : 2 Last member query count : 2 Last member query interval : 1000

  Read the article

• How browsers handle multiple IPs

  - by Sandman4

  Can someone direct me to information on exact browsers behavior when browser gets multiple A records for a given hostname (say ip1 and ip2), and one of them is not accessible. I interested in EXACT details, like (but not limited to): Will browser get 2 IPs from OS, or it will get only one ? Which ip will browser try first (random or always the first one) ? Now, let's say browser started with the failed ip1 For how long will browser try ip1 ? If user hits "stop" while it waits for ip1, and then clicks refresh which IP will browser try ? What will happen when it times-out - will it start trying ip2 or give error ? (And if error, which ip will browser try when user clicks refresh). When user clicks refresh, will any browser attempt new DNS lookup ? Now let's assume browser tried working ip2 first. For the next page request, will browser still use ip2, or it may randomly switch ips ? For how long browsers keep IPs in their cache ? When browsers sends a new DNS request, and get SAME ips, will it CONTINUE to use the same known-to-be-working IP, or the process starts from scratch and it may try any of the two ? Of course it all may be browser dependent, and may also vary between versions and platforms, I'd be happy to have maximum of details. The purpose of this - I'm trying to understand what exactly users will experience when round-robin DNS based used and one of the hosts fails. Please, I'm NOT asking about how bad DNS load balancing is, and please refrain from answering "don't do it", "it's a bad idea", "you need heartbeat/proxy/BGP/whatever" and so on.

  Read the article

• Getting 0xc00000e windows 7 "Boot device inaccessible" after random crashes

  - by Dynde

  I've been having some weird random crashes that I can't seem to locate, and I'm unsure if it's windows or hardware related. It's a brand new computer and very powerful. I've run into a couple of these random crashes, now I don't know what causes them, as it happens during the night, when I'm sleeping. When I wake up, all I see is a boot manager screen that says Exception: 0xc00000e "Boot device inaccessible". A simple restart doesn't fix the problem - it seems to struggle locating my primary hdd - but a complete shutdown works, it'll just fly straight into windows again. The event viewer doesn't tell me much. The most reason incident just gives me this: "The previous system shutdown at 08:55:44 on ?11-?12-?2011 was unexpected." And also a kernel power event: The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. and I can see only two application event entries around that time at 8.47 (about 8 minutes prior to the crash): The Windows Modules Installer service entered the running state. The WinHTTP Web Proxy Auto-Discovery Service service entered the running state. Can anyone tell me anything about this, or direct me to a forum or something that might know what's wrong? I can supply the extra details of the events too if needed. The hdd is an SSD - could that have anything to do with it? I ran a few diagnostics and memory and hdd should be okay - at least the diagnostics report is clean. Is it a faulty drive?

  Read the article

• Slow browsing through IE on Windows Server 2012

  - by Volodymyr

  We've run into strange issue on the freshly installed servers. H/W: IBM server X3550 M4 7914; OS: Windows Server 2012 Std. Then we try to browse on the servers thru IE, not all sites are opened or it takes too long time to open the page, i.e. very few of them can be opened. Local FW are disabled. Servers are in a new subnet and traffic is allowed for it. VLAN is configured properly Another Windows Server 2012 host is running OK and Internet access works fine, but it is VM running on Hyper-V 2012. No proxy is used on the network. At the same time, if one tries to establish telnet session to any site on 80/443 ports - it does work. Google works as well. I've tried to configure single Qlogic adapter to check if the issue remains - it does. Teaming is configured with the means of QLogic, not by built-in functionality. IE Enhanced Security is disabled. IE settings were reset, more than once. Why would certain sites work while others not - Idk. I also tried to disable ecncapability and restart server - no luck netsh int tcp set global ecncapability=disabled Any thoughts? UPD1 VMQ is disabled. Servers are not running Hyper-V. UPD2 Servers were rebuilt from scratch, got a mail a few mins ago. Issue still remains. Teaming is now configured with the means of Windows Server 2012.

  Read the article

• Content not being compressed even though I'm using zlib in php.ini

  - by Tola Odejayi

  I've edited my php.ini file so that it has these two entries: zlib.output_compression = On zlib.output_compression_level = 4 However, after restarting apache, when I request php pages, the headers returned in the response indicate that my server is still NOT serving compressed pages (here are selected headers as viewed using Chrome's Network feature): Cache-Control:no-cache, must-revalidate, max-age=0 Connection:Keep-Alive Content-Type:text/html; charset=UTF-8 Date:Mon, 17 Sep 2012 23:46:13 GMT Expires:Wed, 11 Jan 1984 05:00:00 GMT Last-Modified:Mon, 17 Sep 2012 23:46:13 GMT Pragma:no-cache Proxy-Connection:Keep-Alive Server:Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/0.9.8e-fips-rhel5 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 PHP/5.2.17 Transfer-Encoding:chunked Via:1.1 XXX-PRXY-07 X-Powered-By:PHP/5.2.17 What might I be doing wrong? Is there any other setting that I need to change? EDIT Here is another set of headers returned to another computer: Cache-Control:no-cache, must-revalidate, max-age=0 Connection:close Content-Type:text/html; charset=UTF-8 Date:Thu, 20 Sep 2012 09:45:26 GMT Expires:Wed, 11 Jan 1984 05:00:00 GMT Last-Modified:Thu, 20 Sep 2012 09:45:26 GMT Pragma:no-cache Server:Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/0.9.8e-fips-rhel5 mod_auth_passthrough/2.1 mod_bwlimited/1.4 FrontPage/5.0.2.2635 PHP/5.2.17 Transfer-Encoding:chunked Vary:Cookie X-Powered-By:PHP/5.2.17

  Read the article

• Nginx terminate SSL for wordpress

  - by Mike

  I have a bit of a problem. We run a wordpress blog behind a ngnix proxy and looking to terminate the ssl on the nginx side. Our current nginx config is upstream admin_nossl { server 192.168.100.36:80; } server { listen 192.168.71.178:443; server_name host.domain.com; ssl on; ssl_certificate /etc/nginx/wild.domain.com.crt; ssl_certificate_key /etc/nginx/wild.domain.com.key; ssl_session_timeout 5m; ssl_protocols SSLv2 SSLv3 TLSv1; ssl_prefer_server_ciphers on; ssl_session_cache shared:SSL:10m; ssl_ciphers RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP; location / { proxy_read_timeout 2000; proxy_next_upstream error; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_max_temp_file_size 0; proxy_pass http://admin_nossl; break; It just does not seem to work. If I can hit https://host.domain.com but it quickly switches back to non-secured from what I can see. Any pointers?

  Read the article

• Nginx - Serve blank page on "Bad Gateway" error

  - by TheLittleCheeseburger

  Hello all. I want to use Nginx as a simple reverse proxy, but if the server behind Nginx is down I just was to display a blank page. For some reason this configuration isn't displaying a blank page on error 502 and I can't figure out why. Thanks for your help! user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; use epoll; # multi_accept on; } http { keepalive_timeout 65; proxy_read_timeout 200; upstream tornado { server 127.0.0.1:8001; } server { listen 80; server_name www.something.com; location / { error_page 502 = @blank; proxy_pass http://tornado; } location @blank { index index.html; root /web/blank; } } }

  Read the article

• I want to use OpenVPN to access the web and email from China. How?

  - by gaoshan88

  My question: How do I use my already existing OpenVPN setup to enable secure, remote web surfing and email checking from open wireless hotspots? Some long winded details: I am running Ubuntu and have OpenVPN up and working fine as a server. My client machine connects fine as well. However, that just gets me a secure connection to my home network. What I want is to be able to access my VPN server and surf the web or check email securely from anywhere with an open wireless connection. I am frequently in China and having secure, unblocked access would be a boon (especially since I like to work from tea houses and coffee shops and I've already had a password sniffed and hacked once). I already know how to tunnel over SSH via a SOCKS proxy using something like: ssh -ND 8887 -p 22 [email protected] but since I have OpenVPN I figure why not try it? So... what are the steps involved in making it so I can connect to my VPN and the surf and check mail to my hearts content (slowly to be sure but at least it wold be secure). Thx!

  Read the article

• Configure Nginx to render static files and rewrite file extension or proxy_pass

  - by Pardoner

  I've set up Nginx to handle all my static files else proxy_pass to a Node.js server. It's working fine but I'm having difficulty rewriting the url so that it remove the .html file extension. upstream my_upstream { server 127.0.0.1:8000; keepalive 64; } server { listen 80; server_name staging.mysite.com; root /var/www/staging.mysite.org/public; access_log /var/logs/staging.mysite.org.access.log; error_log /var/logs/staging.mysite.org.error.log; location ~ ^/(images/|javascript/|css/|robots.txt|humans.txt|favicon.ico) { rewrite (.*)\.html $1 permanent; try_files $uri.html $uri/ /index.html; access_log off; expires max; } location / { proxy_redirect off; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Proto $scheme; proxy_set_header Host $http_host; proxy_set_header X-NginX-Proxy true; proxy_set_header Connection ""; proxy_http_version 1.1; proxy_cache one; proxy_cache_key sfs$request_uri$scheme; proxy_pass http://my_upstream; } }

  Read the article

• Apache 2.4 with PHP-FPM

  - by tubaguy50035

  I'm trying to setup Apache 2.4 with PHP-FPM 5.4 using the new modules with Apache 2.4. The following is what I have currently in my virtual host file: <VirtualHost *:80> ServerAdmin root@localhost DocumentRoot /var/www #Directory permissions <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Require all granted </Directory> CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> I have PHP-FPM running using Unix sockets with a sock file located at /var/run/php5-fpm.sock. How do I proxy my requests to this sock file? I've seen some sites say to use ProxyPassMatch and others are saying Rewrite Rule. Are there pros or cons on either side? Also, most sites I'm seeing are showing ProxyPassMatch with a regex to only pass .php files. Could I also send it .html files? For whatever reason, we have a ton of PHP inside .html files. Edit: As noted in the comments, it looks like mod_proxy_fcgi doesn't support Unix sockets. Is there another module I should be using?

  Read the article

• Problem with Outlook 2010 (SMTP AUTH LOGIN)

  - by Filipe YaBa Polido

  **IGNORE THIS QUESTION - SOLVED WITH A PYTHON SCRIPT available at: http://yabahaus.blogspot.com I have to connect one customer Outlook 2010 to a remote server on which I have either no right, neither way to talk to the sysadmin. This is the thing, after installing and reviewing the logs on Wireshark: Outlook Express: HELO machine AUTH LOGIN username base64 encoded password base64 encoded mails go through. Outlook 2010: HELO machine AUTH DIGEST-MD5 response from server Outlook sends just a * AUTH LOGIN password base64 encoded So... I can send mails in the same domain, but can't send outside, it gives me a relay denied message. My point is... Why the h**l Outlook 2010 doesn't send the username AND the password?! It can never login the right way :| With other versions of Outlook it works fine, and with OE works great, it auths and allows to send mail to a different domain. I've googled and nothing worked. I'm pretty sure that I'm not alone with this one. My last resort will be to configure a local proxy/server that relays to the original one :| Any help would be appreciated. Sorry my bad english as is not my natural language. Thanks.

  Read the article

• Samba access works with IP address only

  - by Sebastian Rittau

  I added a Debian etch host (hostname: webserver, IP address: 192.168.101.2) running Samba to a Windows network with a Windows 2003 PDC (IP address 192.168.101.3). The Samba server exports a public guest share, called "Intranet". The server shows up fine in the network, but trying to click on it produces an error dialog, stating I don't have the necessary permissions. So does entering \webserver manually and using \webserver\internet states that the path does not exist. Interestingly, accessing the share by IP address (\192.168.101.2 or \192.168.101.2\intranet) works fine. DNS is configured correctly, and "smbclient //webserver/intranet" on another Linux client works fine. One complicating issue is that the webserver is only a VMware virtual machine running on PDC server. Here is our smb.conf: [global] workgroup = Foobar server string = Webserver wins support = yes ; commenting out these wins server = 192.168.101.3 ; two lines has no effect dns proxy = no guest account = nobody [... snipped some unrelated bits, like logging ...] security = share [... snipped some password-related things ...] domain master = no [intranet] comment = Intranet path = /srv/webserver/contents browseable = yes guest ok = yes guest only = yes read only = yes create mask = 0775 directory mask = 0775

  Read the article

• Why would e-mail from our own domain not be forwarded to gmail

  - by netboffin

  To solve a problem with spam on our server we tried to forward e-mail from our dedicated server's mailserver(matrix smtp service) to gmail, but while most e-mails got through e-mail from our own domain all went missing. They weren't in the inbox or spam or anywhere else. We've had to go back to using the old system, which means my boss gets a huge amount of spam. We have a windows 2003 server with iis 6 and the matrix smtp service installed. I've toyed with the idea of installing a mail proxy like ASSP but it looks pretty complicated. We're hosting 20 domains on the server as well as our own which has an online shop whose payment system depends on email. I can't start playing around with complicated solutions when it could have disastrous consequences and I don't know enough to implement them safely. So my question has two parts: Part One: Why can't we forward e-mails from people using the same domain. If our domain was foobar.com then [email protected] can't receive from [email protected], but he can receive from everyone else. Part Two: Is there a really simple server side solution to spam that would work with matrix? For instance popfile?

  Read the article

• Ubuntu networking issue: two specific machines cannot browse web while connected to network at the same time.

  - by jensendarren

  I have setup a secure wireless network which works very well except for two laptops running Ubuntu 10.10 that can't access the Internet via a browser at the same time. They can both ping sites, wget sites, use skype but when using a browser the page never loads (in Firefox the status bar just sits there saying "Connecting" until it times out.) Here is what we have tried so far (nothing has fixed this issue): OpenDNS Restart networking services Using wired connection rather than wireless Removing all other nodes from the network except the two machines that have this issue Swapped out the router Factory reset the router Reformatted one of the machines and re-installed Ubuntu 10.10 Other things that we have checked: The two machines can connect simultaneously without any issues to other wireless networks in different locations (say in an Internet Cafe or another office) The two machines have unique IP addresses The two machines have unique MAC addresses The two machines can communicate on the network using Skype, wget, ping etc We are not using a proxy on either machine FYI: I have attached output from wireshark. For the test we turned both machines on and pointed them both to the same website. The content loaded on one and not the other. Here is the output from wireshark- (speedyshare.com/files/26228631/machine_output_1 && speedyshare.com/files/26228649/machine2). As you can see the first one worked, the second one didn't. I don't fully understand the output and would appreciate if someone could shed some light on what might be causing this and how we can fix it! Many thanks! Darren

  Read the article

• Log and debug/decrypt an windows application's HTTPS traffic

  - by cweiske

  I've got a proprietary windows-only application that uses HTTPS to speak with a (also proprietary, undocumented) web service. To ultimately be able to use the web service's functionality on my linux machines, I want to reverse-engineer the web service API by analyzing the requests sent by the application. Now the question: How can I decrypt and log the HTTPS traffic? I know of several solutions which don't apply in my case: Fiddler is a man-in-the-middle HTTPS proxy which I cannot use since the application doesn't support proxies. Also, I do not (yet) know if it works with self-signed server certificates, which I doubt. Wireshark is able to decrypt SSL streams if you have the server's private certificate, which I don't have. any browser extension since the application is not a browser If I remember correctly, there have been some trojans that capture online banking information by hooking into/replacing the window's crypto API. Since the machine is mine, low level changes are possible. Maybe there is a non-trojan (white-hat) network log application out there which does the same? There is a blackhat presentation with some details available to read. They refer to Microsoft Research Detour for easy API hooking.

  Read the article

• xauth, ssh and missing home directory

  - by flolo

  We have several servers, and normaly everything works fine, except now... we get a new aircondition installed. This takes 36 hours and for this time almost all servers got shutdown, only 2 remaining servers run for the most important tasks (i.e. accepting incoming email, delivering some important websites, login-server). Everybody was informed that when they need appropiate data from the homedirs they should fetch it before take down. Long story short: Someone realized that he have run a certain program on one of the servers. No Problem, he can remote login into our login server and run the programm there without home directory (binaries are local and necessary information can be copied to the /tmp). That works like a charm until... ... the user needs to run a GUI programm. I find no easy way to make it running, usually ssh -Y honk@loginserver is enough but now the homedirectory is missing and ssh is not able to copy the cookies into ~/.Xauthority (as the file server with the home directories is down). Paranoid as all systemadmins all X-Server just listen locally not on tcp ports, so no remote X connection possible SSH config is waterproof - i.e. no way to set environment variables. My Problem is, that the generated proxy MIT cookie from ssh get lost as the .Xauthority doesnt exist. If I could retrieve it somehow I could reenter it a .Xauthority in /tmp. The only other option (besides changing the config) which came to my mind is, makeing a tunnel (netcat, or better ssh) from the remote host to the loginserver and copy the cookie manually (not sure if it the tcp-unix domain socket stuff works as expected). Any good suggestions (for the future - now our servers are already up)?

  Read the article

• How can I use HAproxy with SSL and get X-Forwarded-For headers AND tell PHP that SSL is in use?

  - by Josh

  I have the following setup: (internet) ---> [ pfSense Box ] /-> [ Apache / PHP server ] [running HAproxy] --+--> [ Apache / PHP server ] +--> [ Apache / PHP server ] \-> [ Apache / PHP server ] For HTTP requests this works great, requests are distributed to my Apache servers just fine. For SSL requests, I had HAproxy distributing the requests using TCP load balancing, and it worked however since HAproxy didn't act as a proxy, it didn't add the X-Forwarded-For HTTP header, and the Apache / PHP servers didn't know the client's real IP address. So, I added stunnel in front of HAproxy, reading that stunnel could add the X-Forwarded-For HTTP header. However, the package which I could install into pfSense does not add this header... also, this apparently kills my ability to use KeepAlive requests, which I would really like to keep. But the biggest issue which killed that idea was that stunnel converted the HTTPS requests into plain HTTP requests, so PHP didn't know that SSL was enabled and tried to redirect to the SSL site. How can I use HAproxy to load balance across a number of SSL servers, allowing those servers to both know the client's IP address and know that SSL is in use? And if possible, how can I do it on my pfSense server? Or should I drop all this and just use nginx?

  Read the article

• Configuring Vmware virtual machines to run under different IPs and PC specs

  - by Alex

  Right now I'm using a simple VmWare virtual machine with preinstalled Win 7. The IP is assigned automatically (it's the same as main OS IP). Is it possible to create several virtual machines that have different hardware specifications and different IP addresses? Here is what I mean regarding these issues: Specs: Certainly, you can easily change some specifications in the Settings menu (RAM size, HDD size), but what about advanced settings? For example: advanced settings for the Processor: is it AMD (2500+,4000+, etc.. ) or Intel (core 2, Pentium, etc..) Ram - is it Corsair 4 Gb 1333 Mhz or Kingston 2 x 2 Gb 866Mhz or something else? Hdd - Is it Seagate Barracuda 80 gb 5400 Rpm or is it Samsung 500Gb 7200 Rpm or some random SSD? Programs that work under a Virtual Machine shouldn't have a clue if that's a VmWare or not. IPs: Every program that's launched under main OS use the real IP: 93.56.xx.xx All programs that are launched under virtual machine A use IP 1: 74.78.xx.xx All programs that are launched under virtual machine B use IP 2: 84.159.xx.xx I believe that you have to use either VPN or Proxy to solve this problem. The Sum Up: The idea is to create 2-3 independent virtual machines with different hardware specifications and IP addresses. Programs that work under a certain Virtual Machine shouldn't have a clue if that's a VmWare or the real PC. Any ideas/tips or experience regarding configuration will be appreciated!

  Read the article

• No LAN and SMB access, and Explorer not responsive, when using a second connection

  - by Lorenzo

  I apologize if this is a duplicate question, I know that there are several questions about multiple connection (LAN + LAN and LAN + dialup) but I haven't been able to find one that fits my scenario. I'm still using Windows XP on my corporate laptop, and I'm connected to the corporate LAN via Ethernet. The LAN NIC has a public IP address, although not accessible externally, obtained via the corporate DNS server. This connection is firewalled and requires a proxy to access Internet. To access Internet sites blocked by the corporate firewall, I use my smartphone via USB tethering. It is seen as a new LAN interface, and I get a private IP address (class 192.168..). There are two problems: The LAN is not accessible, as the default gateway goes to the tethering NIC. I'd like to solve this, but I can live with it. My PC becomes unresponsive if I use Windows Explorer to view local files, or even when I open the start menu. I guess that this is caused by attemps to connect to a mapped network drive. But I disabled the "Client for Microsoft Networks" in the tethering NIC. Why the system still hangs? Of course if I disable the Ethernet NIC, Explorer stops hanging. If you need further details, add a comment. Thanks!

  Read the article

• Equivalent of scp -l bandwidth_cap for .ssh/config?

  - by Mark Bennett

  Short form: You can limit the bandwidth the scp uses with the -l switch, you pass a number that's in kbits/sec. I'd rather set this in my .ssh/config file for certain names machines. What's the equivalent named setting for -l ? I haven't been able to find it. Followup question: Generally, not sure how to map back and forth between ssh command line options and config names, short of doing Google searches or manually comparing man pages on a case by case basis. Is there a table that directly equates the two? Longer form of first question, with context: I've started using ssh config quite a bit, especially now that I need to go through a proxy and do lots of port mappings. I even define the same machine more than once depending on what type of tunneling I need. However, when uploading a large file, it's difficult to do anything else on my machine. Even though I have more download bandwidth than up, I think that scp saturates the link so even my small requests can't reach the Internet. There's a fix for this, using the -l bandwidth command line switch for scp. scp -l 1000 bigfile.zip titan: I'd like to use this in my config instead, so I'd create an additional named entry called "titan-upload" and I'd use that as the target whenever I upload. So instead of: scp bigfile.zip titan: I'd say: scp bigfile.zip titan-upload Or even set different caps depending on where I am: scp bigfile.zip titan-upload-from-home vs. scp bigfile.zip titan-upload-from-work I'm generally on Mac and Linux.

  Read the article

• ubuntu preseed installation keep missing mirror files

  - by JackWu

  Install ubuntu12.04.2 with preseed file, but there is one buggy problem about preseed mirror setting. The symptom here is installing process got stuck. So I track down the log file, and find out the real problem, the installation is looking for a file that's not there. This is just one of them, another pops up if I faked this file. This all happened during preseed, so I believe preseed has something to do with this. I google ubuntu preseed mirror and find this post saying: # If you select ftp, the mirror/country string does not need to be set. #d-i mirror/protocol string ftp d-i mirror/country string manual d-i mirror/http/hostname string archive.ubuntu.com d-i mirror/http/directory string /ubuntu d-i mirror/http/proxy string # Alternatively: by default, the installer uses CC.archive.ubuntu.com where # CC is the ISO-3166-2 code for the selected country. You can preseed this # so that it does so without asking. #d-i mirror/http/mirror select CC.archive.ubuntu.com # Suite to install. #d-i mirror/suite string lucid # Suite to use for loading installer components (optional). #d-i mirror/udeb/suite string lucid # Components to use for loading installer components (optional). #d-i mirror/udeb/components multiselect main, restricted I wonder the difference between d-i mirror/http/hostname and d-i mirror/http/mirror, I mean they all specify a mirror, right? In my preseed file, this is no d-i mirror/http/mirror, and d-i mirror/http/hostname points to my own repo as you might notice in the previous image. Here is my question: Does preseed fetches file/resource from internet, if I use local repo? Why it's looking for file that's not even there? This has bothered for quite time, many thanks in advance to anyone who might give any help.

  Read the article

• Possible Solution for Setting up a Linux VPN Server to Encrypt WLAN Traffic of Macs and iPhones on

  - by GorillaPatch

  I would like to set up a VPN server on debian linux to encrypt wireless traffic coming from my Mac or iOS device. I would like to use a certificate-based solution. Setting up a PKI infrastructure and managing certificates is OK for me. 1. Which server to pick? By looking through the internet and here on stackoverflow I found the following possible solutions: strongSwan IPSec and racoon Which solution is feasible for a linode running debian squeeze? 2. How to configure the network? If I understood correctly a VPN has a virtual network interface as an endpoint on the server side. Naively I would think that I need a DHCP server running on the server to assign a dynamic private IP (like of the class C network 192.168.xxx.xxx) to the connecting clients. Next I think I would need to set up masquerading to NAT the incoming VPN traffic to the real interface directly connected to the internet. Is this the right way to go? Do you have any configuration examples? I often saw VPN configurations used to connect to your home network, but that is not what I am looking for. I have a server up in the internet and want to use it as a proxy to encrypt traffic in insecure network environments like public WLANs.

  Read the article

• SSL Handshake negotiation on Nginx terribly slow

  - by Paras Chopra

  I am using Nginx as a proxy to 4 apache instances. My problem is that SSL negotiation takes a lot of time (600 ms). See this as an example: http://www.webpagetest.org/result/101020_8JXS/1/details/ Here is my Nginx Conf: user www-data; worker_processes 4; events { worker_connections 2048; use epoll; } http { include /etc/nginx/mime.types; default_type application/octet-stream; access_log /var/log/nginx/access.log; sendfile on; keepalive_timeout 0; tcp_nodelay on; gzip on; gzip_proxied any; server_names_hash_bucket_size 128; } upstream abc { server 1.1.1.1 weight=1; server 1.1.1.2 weight=1; server 1.1.1.3 weight=1; } server { listen 443; server_name blah; keepalive_timeout 5; ssl on; ssl_certificate /blah.crt; ssl_certificate_key /blah.key; ssl_session_cache shared:SSL:10m; ssl_session_timeout 5m; ssl_protocols SSLv2 SSLv3 TLSv1; ssl_ciphers RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP; ssl_prefer_server_ciphers on; location / { proxy_pass http://abc; proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } The machine is a VPS on Linode with 1 G of RAM. Can anyone please tell why SSL Hand shake is taking ages?

  Read the article

• Exchange 2010 certificate errors

  - by Frederik Nielsen

  I have a problem with my newly setup Exchange environment for our hosted customers. First off, when configuring the outlook client, it gives a certificate warning although the certificate has been bought and setup. I am using a setup like this: autodiscover.CUSTOMERDOMAIN.TLD CNAME autodiscover.exchange.COMPANYDOMAIN.TLD (Companydomain is our company that hosts the exchange servers, customerdomain being the customers domain) Shouldn't that work? I know that Microsoft does something like that for Office365, but I really don't think they buy a certificate for every customer.. So I guess some redirection should be setup somehow - any guidance? Next thing: When we accept that error, and move on to actually starting Outlook, it states that the certificate is not valid for the RPC proxy server exchange.COMPANYDOMAIN.TLD - this domain is not right, as that domain is not included in the certificate. I would instead like this domain to be mail.exchange.COMPANYDOMAIN.TLD I tried to run this script setting both internal and external URL's to be the same, with no luck. Any guidance on this one? I am running Exchange 2010 SP2, with CAS, HT and MBX split up on 3 different servers.

  Read the article

• Problem with Outlook 2010 (SMTP AUTH LOGIN)

  - by Filipe YaBa Polido

  I have to connect one customer Outlook 2010 to a remote server on which I have either no right, neither way to talk to the sysadmin. This is the thing, after installing and reviewing the logs on Wireshark: Outlook Express: HELO machine AUTH LOGIN username base64 encoded password base64 encoded mails go through. Outlook 2010: HELO machine AUTH DIGEST-MD5 response from server Outlook sends just a * AUTH LOGIN password base64 encoded So... I can send mails in the same domain, but can't send outside, it gives me a relay denied message. My point is... Why the h**l Outlook 2010 doesn't send the username AND the password?! It can never login the right way :| With other versions of Outlook it works fine, and with OE works great, it auths and allows to send mail to a different domain. I've googled and nothing worked. I'm pretty sure that I'm not alone with this one. My last resort will be to configure a local proxy/server that relays to the original one :| Any help would be appreciated. Sorry my bad english as is not my natural language. Thanks.

  Read the article

< Previous Page | 174 175 176 177 178 179 180 181 182 183 184 185  | Next Page >