Search Results

Search found 6619 results on 265 pages for 'gnome activity journal'.

Page 179/265 | < Previous Page | 175 176 177 178 179 180 181 182 183 184 185 186  | Next Page >

  • How do you add more space to a Fedora (LVM) partition?

    - by Trevor Boyd Smith
    In a nutshell, i have a VM that ran out of space. I increased the size of the VM's harddrive to be 4 times bigger but the OS partition is still only using 1x the space. I need to change the LVM partition to take up the extra 4x space but I don't know how to extend the LVM partition. (NOTE: To make the screenshots given below I had to boot from a live-cd for gnome-partition-manager (aka gparted). Very unfortunately gparted is only able to "detect LVM" and can't do any LVM operations.) Here is what "gparted" shows. Please notice that the "resize" option is not available: The Problem: I can't find good directions<1 on how to grow the LVM partition via GUI or command-line! How do you grow a LVM partition that was created by the default Fedora install? If you are giving command line directions. Please explain what each line of commands does.

    Read the article

  • What would make a noise in a PC on graphics operations on a passively-cooled system?

    - by T.J. Crowder
    I have this system based on the Intel D510MO motherboard, which is basically an Atom D510 (dual-core HT Atom w/built-in GPU), an Intel NM10 chipset, and a Realtek Gigabit LAN controller. It's entirely passively cooled. I noticed almost immediately that there was a kind of very, very soft noise that corresponded with graphics operations, sort of the noise you'd get if you had a sheet of flat paper and slid something really light across it — but more electronic than that. I wrote it off as observation error and/or disk activity triggered by the graphics operation (although the latter seemed like a lot of unnecessary disk activity). It isn't. I got curious enough that I finally did a few controlled experiments, and here's what I've determined: It isn't the HDD. For one thing, the sounds the HDD makes (when seeking, when reading or writing, when just sitting there spinning) is different. For another, I used sudo hdparm -y /dev/sda (I'm using Ubuntu 10.04 LTS) to temporarily put the disk on standby while making sure that non-disk graphics op was happening in a loop. The disk spun down, but the other sound continued, corresponding perfectly with the timing of the graphics op. (Then the disk spun up again, but it takes long enough that I could rule out the HDD.) It isn't the monitor; I ensured the two were well physically-separated and the sound was definitely coming from the main box. It isn't something else in the room; the sound is coming from the box. It isn't cross-talk to an audio circuit coming out the speakers. (It doesn't have any speakers.) It isn't my mouse (e.g., when I'm trying to make graphics ops happen); the sound happens if I set up a recurring operation and don't use the mouse at all, or if I lift the mouse off the table slightly (but enough that the laser still registers movement). It isn't the voices in my head; they never whisper like that. Other observations: It doesn't seem to matter what the graphics operation is; anything that changes what's on the screen seems to do it. I get the sound when moving the mouse over the Chromium tab bar (which makes the tab backgrounds change); I get it when a web page has a counter on it that changes the text on the page: I get it when dragging window contents around. The sound is very, very slightly louder if the graphics op is larger, like scrolling a text area when writing a question on superuser.com, than for smaller operations like the tick counter on the web page. But it's very slight. It's fairly loud (and of good duration) when the op involves color changes to substantial surface areas. For instance, when asking a question here on superuser and you move the cursor between the question box and the tag box, and the help to the right fades out, changes, and fades back in. (Yet another example related to the web browser, so let me say: I hear it when operations completely unrelated to the web browser as well.) It doesn't sound like arcing or anything like that (I'd've shut off the machine Right Quick Like if it did). Moving windows does it. Scrolling windows (by and large) doesn't. I have the feeling I've heard this sort of thing before, when all system fans were on low and such, with other systems — but (again) written it off as observational error. For all the world it's like I'm hearing the CPU working (as opposed to the GPU; note the window scroll thing above) or data being transferred somewhere, but that just seems...unlikely. So what am I hearing? This may seem like a very localized question, but perhaps other silent PC enthusiasts may be interested as well...

    Read the article

  • How to get Mac OS X Terminal.app and screen/vim scrolling to play nice?

    - by rustychains
    OSX 10.6.3 Terminal.app Am a pretty dedicated screen user. Terminal.app line buffer and/or scroll does not seem to work for me. That is while in screen anything that goes past the top of the frame is gone, can't scroll back to. This seems to work ok in other terminal apps gnome, cygwin. Perhaps this is a shell env, config, or command? .screenrc: startup_message off autodetach on shell -$SHELL vbell off defutf8 on caption always caption string "%{= wk}%w" I have tried using defscrollback here with different values, but doesn't have an effect. some .bashrc settings: set -o physical export TERM=xterm-color shopt -s checkwinsize

    Read the article

  • Understanding the Linux boot process, subsystem initialization, & udev rules?

    - by quack quixote
    I'm creating UDEV rules for automounting external drives on a headless server, much in the same way as Gnome-VFS does automounting during a user session. I'm concerned with the rule's behavior at boot-time. There's a good chance one of these drives will be connected during a boot, and I'd prefer any connected drives get mounted in the right place. The drives might be either USB or Firewire, and they are mounted from a shell script fired off by UDEV on detecting an "add". Here are my questions: When UDEV runs the mount for these devices at boot, will the system be ready to mount it? Or will the script get triggered too early? If it's too early, what's a good way for a script to tell that the system isn't ready yet (so sleep a while before checking again)? The UDEV rule matches ACTION=="add". Does this event even fire at system boot?

    Read the article

  • Focus Follows Mouse or Sloppy Focus on Mac OS X

    - by jtimberman
    "Focus follows mouse" or "sloppy focus" is a feature common to X11 window managers on Linux/Unix, including GNOME, KDE, CDE, XFCE and window managers like Enlightenment, Fluxbox and Window Maker. It is also available via TweakUI on Windows. Some individual applications on OS X, like iTerm support it. What is it? Simply put, the window where the mouse pointer is has focus, rather than having to click a window for it to gain focus. Does the native GUI for OS X support this, with some hidden setting? Or, is there a good third party application that will do this?

    Read the article

  • Multiple interfaces to one IP address?

    - by Delan Azabani
    At present, I have: a Netgear router with DHCP off at 192.168.0.1 my computer eth0 at 192.168.0.2 wlan0 at 192.168.0.2 The wlan0 interface always connects to the router, while the eth0 interface connects to other computers with crossover and acts as a dnsmasq DHCP server for network boot and installation. If I use the Gnome NetworkManager to enable both connections, that is, with wlan0 connected to the router/internet and eth0 to another computer, both as 192.168.0.2, I cannot access the internet while eth0 is connected. Why is this? How can I configure my computer to follow wlan0 for Internet usage, but use eth0 for itself (the latter is working but blocking wlan0).

    Read the article

  • buggy mouse click after a while

    - by sputnick
    The cursor of my mouse is moving as well on my twin view, but after a WHILE, or if I start kde with runlevels (I don't know why, but startx works better) I can't click anything. I have had replaced the mouse with another one, but it's the same problem, so it's not a hardware problem. The problem occurs both with gnome and kde. My config : PC Dell Optiplex 780 archlinux x86_64 (up to date) xf86-input-evdev 2.6.0-4 xorg-server 1.11.2-2 kernel linux-3.1.1-1-ARCH My Xorg log doesn't contains "EE" string for errors. Any clue ?

    Read the article

  • How to mount remote samba share from local host with multiple groups?

    - by Dragos
    I am using mount.cifs to mount a remote samba share (both client and server are Ubuntu server 8.04) like this: mount.cifs //sambaserver/samba /mountpath -o credentials=/path/.credentials,uid=someuser,gid=1000 $ cat .credentials username=user password=password I mounted a user from local system with username and password with mount.cifs but the problem is that the user is part of multiple groups on the remote system and with mount.cifs I can only specify one gid. Is there a way to specify all the gids that the remote user has? Is there a way to: Mount the remote samba with multiple groups on the local system? Browse the mount from 1) with the terminal since I want to pass some files from samba as arguments to local programs. Other solutions would be: nautilus sftp:// which runs through gvfs; but the newer gnome does not write to disk the ~/.gvfs anymore so I can't browse it in terminal. And the last solution would be NFS but that means that I have to synchronize the uids and gids on the local system with the ones from the server.

    Read the article

  • Stop a particular key getting captured by rdesktop

    - by user18151
    Hello, I want F12 to be not capture by my rdesktop while in fullscreen, so that I can do whatever stuff I'm doing on my remote Windows computer, but pressing F12 would bring down yakuake, and I can type down my commands, or use vim etc for whatever I'm doing. Is there any possible way to do this? I tried playing with keymaps, but that didn't help. I set F12 to inhibit, but that seems to have stopped sending F12 altogether, rather than let gnome catch it and let yakuake pop up. Would be really grateful for answers. I am ready to do my homework, if someone could please just give me pointers etc. Thanks :). Sidenote: My current arranement stems from my large monitor in lab, and small personal laptop monitor, and the laptop has Windows 7. My lab computer has Linux, on which I do my coding work.

    Read the article

  • Lightweight Live Linux Image

    - by MA1
    I am working on an application which is being developed in wxPython and C plus using linux core utilities and network support. To be more specific, I only need the following support for following packages/softwares/components. wxPython C Network Support Linux Utilities Vi File System(fdisk/parted, ntfsprogs etc) Basic(cp, mount/umount, mkdir etc) The application will run from a live CD. Currently i am using Fedora 12 with Gnome for live CD. Currently the size of live image is around 350 MB. The size of application is hardly 1 MB. I don't need anything else except above mentioned. Just my application and supporting packages, no desktop etc. So, I need a Lightweight Linux image as smaller as possible providing all the above mentioned packages/components. I am considering the following distributions: Xfce LXDE Fluxbox Enlightenment Any ideas/suggestions?

    Read the article

  • something is downloading in background Linux

    - by wisdom
    My laptop boots normally to Linux -LinuxMint- and immediately I like to open gnome-system-monitor but the shock is that something is downloading(the problem has been out 2 days ago) and nothing I run yet ! I did iftop in terminal but nothing strange -a screen shot provided-, also I tried nethogs which showed nothing at all. The more complicated when I reboot and same problem is there so I can't browse/surf Internet, no one connected to my network can browse any more it's absorbing the stream horribly! After many reboots it will go to normal state(no background downloading). But really I can't figure out the problem going behind the scene ! Any suggestion,any help would be appreciated...thanks

    Read the article

  • How to get osx terminal.app and screen/vim scrolling to play nice?

    - by rustychains
    OSX 10.6.3 terminal.app Am a pretty dedicated screen user. Terminal.app line buffer and/or scroll does not seem to work for me. That is while in screen anything that goes past the top of the frame is gone, can't scroll back to. This seems to work ok in other terminal apps gnome, cygwin. Perhaps this is a shell env, config, or command? .screenrc: startup_message off autodetach on shell -$SHELL vbell off defutf8 on caption always caption string "%{= wk}%w" I have tried using defscrollback here with different values, but doesn't have an effect. some .bashrc settings: set -o physical export TERM=xterm-color shopt -s checkwinsize

    Read the article

  • getting Ubuntu-quality fonts / configuration under Cygwin/X

    - by user5402
    I have Cygwin/X installed on a Win7 box. I also have an Ubuntu VM running on the Win7 host. If I do the following: Start Xming on the Win7 box Start mate-terminal under Cygwin/X then mate-terminal starts up with very crappy-looking fonts and a blinking cursor. (I'm using "Monospace 10" in mate-terminal.) If I then do: Use putty to ssh into the Ubuntu VM (fowarding the X connection) Run gnome-settings-daemon on the Ubuntu VM then the fonts in mate-terminal suddenly become much better looking and the cursor stops blinking (probably because I've configured it that way in Ubuntu.) Question: How can I get the better-looking fonts and the ability to set cursor-blinks option for mate-terminal under Cygwin/X without having to run the Ubuntu VM? FWIW, I have Xming-fonts-7-5-0-4 installed. Update: Starting Xming with '-dpi 101' as suggested here helps, but the fonts are still not anti-aliased.

    Read the article

  • How to discern video details from Linux Live CD

    - by Chris Lieb
    I was having trouble getting X.Org to work with the video card in a recently aquired laptop, so I decided to try to probe around the configuration of a Linux Live CD to figure out how to set up my kernel. I chose the Sabayon 5.0 Live DVD because it was the only one that I could find that was the same or newer than the 2.6.32 kernel I have installed on the laptop right now. Of course, the DVD booted right into GNOME without issue, unlike the hangs and crashes that I had been getting. So, I want to figure out what kernel driver this Live DVD is currently using, but I don't know how to. hwinfo doesn't shed any light on the matter, and lspci -vnn doesn't list a driver for my video device, though both methods correctly identify that I have an Intel 855GM video processor. How can I find out this information?

    Read the article

  • Indexing text file content with command line query

    - by Drew Carlton
    I take daily notes in a plaintext file labeled with date in the YYYYMMDD format. These files are no more than 100 lines long, and are written in a blog style format. I'd like to be able search these files as if they were blog posts indexed by google, with some phrase query returning the most relevant/recent date filenames, with a snippet containing the relevant part. Ideally it would be something like this: #searchindex "laptop no sound" returns: 20100909.txt: ... laptop sound isn't working... 20100101.txt ... sound is too loud... debating what laptop to buy... and so on and so forth. I'm working on a linux platform (Debian with GNOME). I've looked at beagle and tracker, but they just seem complete overkill for what I want.

    Read the article

  • Ubuntu: Is there a good tabbed PDF viewer?

    - by Frank
    Is there a good non-bloated PDF viewer for (Ubuntu) Linux that supports tabs? I don't want to use Acrobat Reader because it is slow and takes much memory, and my computer isn't the fastest. I know the alternative readers evince and foxit, but they don't support opening different PDF files in tabs. (foxit has that feature on Windows, but the Linux version 1.1, which I just tried, doesn't have it.) For evince, I know many people would like this functionality, but they get ridiculed by Ubuntu people (see here), who say that tabs are the task of a window manager. If that is the case, how can I put all evince windows into one in GNOME?

    Read the article

  • What GUI systems let you copy text with formatting preserved, via clipboard?

    - by culebrón
    If you select and copy a text from Internet Explorer and paste it in Miscrosoft Word, the formatting is preserved. If you do that in Opera or Firefox in Windows, it's lost, IIRC. I use Gnome desktop in Linux, and formatting is preserved nowhere, which is very inconvenient. Even if desktop lets me copy formatted text, I can't post it into any web form: WISYWIG Javascript forms will strip formatting and make me walk through the whole text and fix it manually. I don't know how things are in Macs. Is there a desktop + browser + editor set that allow passing formatted text consistently throughout?

    Read the article

  • Computer freezes for 2+ seconds, mouse still moves

    - by xsaero00
    I have this problem on my workstation. The computer would effectively freeze for 2-5 seconds for no apparent reason, then continue as normal. While frozen the mouse would still be movable, but only on one of screens in my multi-screen setup. What can be the likely cause. System: CPU: i7-920 Memory: 12G of Patriot DDR3, 6 modules OS: SLED 11, Suse Linux Enterprise Desktop, using Gnome Main board: Asus P6T Video: two Nvidia 9500GT connected to three displays I am using memory at recommended settings of 8-8-8-1333. It has an XMP profile. Th CPU is a bit overclocked to 3.3 GHz, but my cooling more than allows for it. I ran the computer with all overclocks off and lower memory speed but the issue was still there. Any ideas? Where should I start looking?

    Read the article

  • Ubuntu login takes 15 seconds, "I/O error dev fd0 sector 0"

    - by Dan
    After upgrading to Ubuntu 10.04, when I first login it takes 10+ seconds where it just sits at the gdm backgroup before taking me to gnome. By switching to a terminal window during this 10 seconds I saw the error message "I/O error /dev/fd0 sector 0" being outputted. I assume this has to do with the floppy drive... but I don't even have a floppy drive! How do I disable this device and make this error message go away (and hopefully fix the long wait)? Thanks.

    Read the article

  • Share history in multiple zsh shell

    - by michael
    I am trying to setup zsh so that it shares command history between different zsh sessions: in multiple tabs in multiple gnome-terminals in different screen sessions I have put this in .zshrc #To save every command before it is executed (this is different from bash's history -a solution): setopt inc_append_history #To retrieve the history file everytime history is called upon. setopt share_history but that does not work. e.g. I type 1 command: gedit afile and then I go to and zsh and type history. I don't see gedit afile. output of 'setopt' is % setopt nohistbeep histexpiredupsfirst histfindnodups histignorealldups histignoredups histignorespace histnostore histreduceblanks histsavenodups histverify incappendhistory interactive monitor promptsubst sharehistory shinstdin zle How can I achieve this?

    Read the article

  • Using screen, commands like less and man don't clear the screen afterwards

    - by Boldewyn
    In contrast to this question I want the clearing of the screen re-enabled for less. It works fine in my xterm terminal under Cygwin/mintty or Gnome Terminal (both xterms). However, when inside a screen session, the clearing of the screen is somehow disabled. I tried several things, like screen -T xterm or putting the autonuke statement in my ~/.screenrc. Also, inside the screen session export TERM=xterm tset has no effect. So, now I'm out of ideas. Any help appreciated.

    Read the article

  • tmux: unbind C-[ as a prefix

    - by StanAngeloff
    I have a fairly straight forward .tmux.conf file which does nothing more but to define a couple of options, such as history-limit. I have not added any custom key bindings yet. I find it extremely annoying that I cannot unbind C-[ as a prefix in tmux. Here is what I mean: $ uname -a Linux stan-inspiron 3.2.0-24-generic #39-Ubuntu SMP Mon May 21 16:52:17 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux $ tmux [0] 0:~* "stan-inspiron" 10:05 12-Jun-12 % vim Whilst inside vim, when I go to insert mode and then use C-[0 to escape insert mode and move to the first character on the line, tmux grabs the key first and complains: Window not found: :0 ** I tried all sorts of things in my .tmux.conf, but nothing works. I thought it might be a terminal or shell issue, but confirmed same behaviour on a configless machine using Bash and [Gnome] Terminal. So the question really is, how do I unbind the C-[ key from tmux? ** I have base-index 1 set.

    Read the article

  • Which window manager do you use?

    - by Stephan202
    Combining "What is your default web browser?" and "What are the differences between Linux Window Managers", I ask you: which window manager do you use, and why? Myself I prefer a minimal window manager on the one hand (in the past I used Fluxbox), but on the other hand wish to go with the main stream, to ease finding (Googling) solutions in case of problems. Hence I stick with Gnome as it is shipped with Ubuntu. Why do you use the window manager which you use? I understand some reasons may be subjective, but please try to cite technical reasons where possible.

    Read the article

  • I'm running Ubuntu notebook on a USB drive with 1GB persistence. Where are my XAMPP files?

    - by CDeanMartin
    I just began running Ubuntu Notebook on my 2GB USB stick, with 1GB persistence. After I installed XAMPP, I rebooted to make sure the persistence was working. It worked! My XAMPP installation worked, and it comes up when I type localhost into the browser. The sample apps work, including the ones using MySQL. But I can't find the application files! I am used to the vast labyrinth of files in Windows Explorer, and looking through 'Files and Folders' in GNOME, there seem to only be 7 or 8 folders in the entire OS? What is really going on here? I looked through them all and where is XAMPP? When I code PHP with a WAMP stack, all the .php files go in the 'WWW folder' What is the Linux equivalent of the WWW folder?

    Read the article

  • Getting kernel errors when manually mounting VirtualBox shared folders

    - by Ross
    Updated: I've rephrased this problem as I understand it a bit more now (and have encountered another problem). I'm using a Fedora 15 guest on a Windows 7 host using VirtualBox. I am trying to mount a partition on the host PC as a shared folder for use in the guest. The folder appears in /media and is accessible when I use the auto-mount feature when setting up the shared folder, but when I attempt to mount without auto-mount I get the following error: $ sudo mount.vboxsf data /mnt/host_data /sbin/mount.vboxsf: Could not add an entry to the mount table.: Invalid argument In addition a popup appears (part of Fedora/GNOME) reporting a crash in the kernel package: WARNING: at lib/list_debug.c:26 __list_add+0x3e/0x81() However the shared folder seems to work, I can certainly browse it (although everything seems to be executable, probably down to a Windows host). Is there something wrong with what I'm doing or is this a bug (and in which case should it be reported to the Linux Kernel team or VirtualBox)?

    Read the article

< Previous Page | 175 176 177 178 179 180 181 182 183 184 185 186  | Next Page >