Search Results

Search found 693 results on 28 pages for 'mutli wan'.

Page 18/28 | < Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >

• Apache doesn't autostart because vpn isn't up yet.

  - by Col. Shrapnel

  I have a FreeBSD8 server, and VPN connection to my ISP. I use mpd5 and it works fine. A have an Apache server whch works fine, if I start it manually, after VPN is get up. But when I add it to rc.conf autostart, it fail to start, saying (49) can't assign requested address: make_sock could not bind to address I suppose it's because VPN isn't up yet and no IP address assigned to the interface which i set in the Listen directive in the httpd.conf. If i set Listen to the existing 127.0.0.1, it fail to serve wan requests. Is there a solution, either to delay apache autostart or configure it some different?

  Read the article

• Cisco T1 Routing Help

  - by Joseph

  Thanks to someone on this site I was able to get the Serial0/0 interface up. I now have: DCD=up DSR=up DTR=up RTS=up CTS=up My next challenge seems to be in the routing and/or PC ip setup. This are the pertinent details from L3: WAN Network: 6.59.186.60/30 Level3 Side: 6.59.186.61 Customer Side: 6.59.186.62 Cust. LAN IPs: 6.59.192.224/27 What would be the IOS commands to setup this route correctly? Am I correct that I would the choose an IP like 6.59.192.224, subnet 255.0.0.0, gateway 6.59.186.62? Thanks

  Read the article

• Google Docs: Tie the Form with a Spreadsheet to email addresses and responses?

  - by Nick Gorbikoff

  Hello. I'm just trying to figure out if I'm doing something wrong or it's not possible. I created a small form ( I'm trying to get current mailing addresses from my friends and relatives - since I lost my address book) and it ties to a Google Spreadsheet. I sent out a sample to my work address - filled out a form and saved it. However when I go to see the responses - in a spreadsheet - it has a time stamp but it has no email associated with a response - so I don't know who made it ( well in this case I know it's me - but when you have 100 replies?) I understand - it may be great for anonymous surveys - but in this case I'd like to know who responded with what - and I don't wan to make them fill out Email and First Name & Last Name - I already have this information. Any suggestions?

  Read the article

• How to forward blocked ports by ISP

  - by KiDo

  So I've been trying to setup a TeamSpeak 3 server on my pc but ports (9987,10011,30033) are blocked by my ISP, I've contacted them to unblock them but they didn't accept, and it's the fastest ISP in my city (as living in a 3rd world country) so it's not a good idea to connect to another ISP. The thing is, I've tried Your-Freedom to connect to tunnel my connection & SocksCap. The problem is, when TS works with SocksCap it doesn't show a WAN-IP that friends will use to connect to my server It says "Needs to be Requested" and when I press the Request button, I get nothing. So, any idea what's wrong if someone has done this before? or if you have any other suggestion to run a TS server, would be very glad to hear it and really appreciate that. P.S. as I've mentioned before, living in a 3rd world country, makes me unable to buy a VPS even the cheapest one cause there's no Visa, Credit, or paypal. so that won't work. Thanks in advance.

  Read the article

• Sharing internet connection from Windows XP using wi-fi router

  - by Darius

  Hi, I have an network configuration like: Ethernet cable from ISP connected to Windows XP machine, configured with static IP 192.168.0.3 Another ethernet connection from 2nd Windows XP machine's network adapter to a Wi-Fi router (D-Link Airport G+) XP set to "Share internet connection", the 2nd adapter configured as static to 192.169.0.1 D-Link Airport Wi-Fi router also configured as "static connection", it's IP set to 192.169.0.2, default gateway set to 192.169.0.1. Network mask everywhere is 24. Laptop computer connected with the router with static IP 192.169.0.3 The problems are: XP machine sees the router (it's able to ping it and access it via the web admin tool) The router somehow cannot PING the XP machine (using the tool provided by the web-based admin tool) The laptop computer cannot ping anything and cannot be pinged The router is only accessible when the ethernet cable is connected with a router's 1-4 LAN port, when I connect it via "WAN" port (which I believe is the proper one) it's not visible from the XP machine If you have similar experience with configuring a network like this I would really appreciate your help. I cannot use the Wi-Fi router with the ISP cable itself.

  Read the article

• Unexpected network traffic?

  - by robwalker

  My internet connection is via a fixed wireless connection using a 900MHz Motorola Canopy module. The router reports a fairly consistent 32-64Kbps of incoming traffic on the WAN port. When I attached a PC directly to the port and run Wireshark, I get a dump showing a lot of chatter from other machines that I presume are connected to the same tower. This didn't include end-to-end traffic, but was there were a lot of ARP requests, SSDP traffic, ICMP and other network discovery type stuff. Is this 'normal' or does it suggest a misconfiguration somewhere? As far as I can tell there is no need for my modem to be receiving any of this traffic (other than wanting to know what the names of my neighbours machines and printers are!) Since the internet connection is slow at the best of time, having this amount of background noise seems very wasteful.

  Read the article

• setup advanced filtering and access restrictions on dd-wrt using iptables

  - by Nova deViator

  I have a linksys WRT54GL router with a DD-WRT installed and I want to setup some advanced filtering that seem to not be available through "Access restrictions" web gui option. I guess I would be using IPTABLES then. I have ssh access to router and can run iptables, but I'm not so experienced with iptables. So here are my needs: my policy would be deny all first and then allow exceptions allow all http (port 80) access to WAN through wireless allow all other traffic only to PCs with specific MAC addresses allow internet access to PC with specific MAC address according to schedule (let's say everyday between 18:00-21:00) is this possible to setup with IPtables? could somebody help me a bit with it? or should go and RTFM?

  Read the article

• How can I stop Windows DNS server properties settings from changing by themselves?

  - by paradroid

  When I open the DNS console in Administrative tools, I keep finding a couple of problems which keep on reappearing by themselves, and I want to stop them from happening. One of the DNS servers has two network interfaces, and it should only be listening for requests on of them, and I get errors in the Event Log otherwise. But when right clicking one DNS server and selecting Properties, I can see on the Interfaces tab that 'All IP addresses' is selected. If I Change it to 'Only the following IP addresses:' and deleselect the WAN addess, I will find it reslected when I next check it after a couple of days. In the other DNS server's Properties, on the Forwarders tab, there should only be two forwarder addresses. However, the address for the router keeps in appearing. This router has the DNS server as its forwarder. There shouldn't be anything using the router's DNS forwarders for DNS other than the router itself, but this surely is causing a loop. How do I get these properties on both DNS servers to stick?

  Read the article

• 2wire modem to linksys router

  - by Imajica666

  I want to hook a Linksys router to my 2wire modem/router (2701HG-b) to share my Internet connection. I ran from an open port from the 2wire to the WAN port of the Linksys but it will not work. I did this before with my cable modem to a router to my Linksys router. It worked then but not now. I read I can turn the 2 wire into a modem only but I need the 2wire wireless access also. IPCONFIG /ALL sees the 2wire with IP info as well as DHCP server/gateway. Any ideas?

  Read the article

• Setting up wifi router as a switch for Internet Connection Sharing

  - by William C

  Can my laptop with a 3G connection share its Internet via a Wifi router (Dlink DIR-615)? I turned Internet Connection Sharing on and Windows assigned 192.168.137.1 to my laptop's LAN adapter. Do I connect my laptop to the WAN port or to the LAN port of the router? What should I set as my router's IP address? Do I turn DHCP on my router on? Do I assign 192.168.137.x as static addresses on the other computers? If not, what? Is there anything else I need to set on my router? Thank you!

  Read the article

• Routing from the DMZ to the interior network only

  - by Allan

  I have a home network connected to Verizon's FIOS service. Verizon's ActionTec router is connected to the ONT via coax to establish the MOCA network. My DD-WRT router's WAN port is connected to one of the ActionTec's LAN ports. The DD-WRT router is configured with a static IP address and assigned to the DMZ (this is done so I only have to configure port forwarding once). My issue is that this does not allow computers connected to the DD-WRT to serve streaming audio/video to the MOCA network using Verizon's Media Manager. I know that Media Manager uses ports 18001, 5050, and 5060, but I don't know how to forward those ports so that they are only available to the ActionTec's network and not the rest of the internet.

  Read the article

• Why does my wifi fail to stay connected?

  - by Mark0978

  We have 5 different laptops in the house, 1 macbook, 1 Compaq, 3 dells, plus numerous little devices like ipods, squeezeboxs, squeezebox radios and controllers, you name it. All of them connect to and stay connected to the "downstairs" WIFI just fine. But my laptop (the most expensive of the lot) refuses to stay connected, preferring the much weaker and slower signal upstairs. My laptop is running Win7 (64 bit) Ultimate with an Intel 3945ABG WIFI contoller (It's a Dell Precision M6300). The WIFI Access Point is a Cisco WRT54G2 V1 with firmware: Firmware: DD-WRT v24-sp2 (10/10/09) micro Time: 11:11:10 up 42 min, load average: 0.06, 0.01, 0.00 WAN: Disabled

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - Setup guide recommendations?

  - by Peter Mounce

  I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. My ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

• Access my router's gateway network?

  - by Danpe

  I have 2 routers in my place. Main Router (Connected to the Internet) - 192.168.1.1 Secondery Router (Connected to the Main Router) - 192.168.0.1 I have a Network Storage Device and few Shared Directorys connected to the Main Router. (Network Storage - 192.168.1.16) How can i acces one of them using a PC connected to the Secondery Router? Home Network Diagram: I currently have access to the internet using both laptop and Main PC. But i want to get access from my laptop to the Storage and to ym shared directorys. The problem is the my Main router always forwards all packets stright to the WAN.. (Internet)

  Read the article

• How to ssh to my dorm computer with shared public IP and no admin rights over the router?

  - by Aamir

  First of all, I am not a Linux or ssh newbie. I have searched for this problem on many forums extensively but nobody seemed to have discussed this. Please help me! I live in a student dorm (off-campus) and all students of the dorm share the same WAN IP (Internet or public IP), which is fortunately static. I am not an admin and have no control over the router that assigns private IP's to all of the students, so I can't really forward port 22 to my computer :( Is it still possible to establish an ssh connection to my dorm computer from a computer on campus?

  Read the article

• Fortigate VPN Routing issue

  - by user1571299

  I have 200B Fortigate unit with 2 internet WAN connections. I also have a remote site which I'm connected to via IPSEC VPN through WAN1. This site has only one GW IP address. I'd also like to setup a VPN ontop of WAN2 with that specific site as it's destination. The default route for my end is WAN1. My problem is I cant figure out how to have both tunnels up at the same time. What's the best practice for achieving this? Thanks

  Read the article

• Configuring Wireless Network

  - by Vinod K

  I have vyataa router on VMware with 2 interfaces eth0 and eth1 eth0 is facing the internet eth0 is in Nat mode with dhcp on eth1 is in bridged mode with my ethernet with ip 10.0.2.34/24 The ethernet card is at ip 10.0.2.95/24 i have defined the nat rule. Hence internet is available at eth1 too. Now i am connecting a wireless router at "eth1" iball router, I have connected the router using a cable to the ethernet interface of my laptop. I have configured the WAN connection type as "Static IP" and given "10.0.2.34/24" All the clients that connect using wireless router cannot connect to the internet though. Could anyone provide me a solution for this.. Thank You!!

  Read the article

• Server 2008 R2 Datacenter (and all other version) not detecting hardware

  - by Mitchell Skurnik

  I upgraded my ASUS KFN32-D SLI/SAS motherboard to the latest BIOS version and swapped out the 2 dual-core procs with 2 quad core procs. After installing Server 2008 Datacenter onto the system I noticed that it was not connected to the network. I open device manager and see no network adapters. I have to go up to View - Show hidden devices to even see the virtual WAN Miniport adapters. This problem happens in Vista and Windows 7 (all x64). What is even stranger is it all works in x86 mode. What in x64 could be causing windows to not even detect hardware that works in x86? Is the boot manager possibly the culprit?

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

  - by Peter Mounce

  I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

  - by Peter Mounce

  Crossposted from here I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

• How a router decides destination of packet?

  - by user58859

  I have basic networking question. Scenario : Two pc's are communicating on a wan. Both the pc's ate behind routers or modems. My question : Both the pc's have public IP of each other. That public IP is most of the time is either of the router or of the modem. There can be more then one pc's behind those routers and modems. Then how the pc's are communicating. I can understand the packets can reach upto those routers or modems. But what after that. In the packet , destination IP is public IP. Then how the router or modem decides where to send the packet? Can anybody explain me this please. Thanks in advance.

  Read the article

• how long does noip ddns takes to make the updated address again accessible?

  - by neoDev

  Yesterday I've created a noip account, I've downloaded the updater client (DUC), I've configured them, and when I've tryied to browse "myaddress.noip.me" all worked fine... When my WAN IP changes, the DUC client quickly updates it in few minutes, and in my account on noip.com I can see that it is also refreshed properly. But the problem is that if I try to browse "myaddress.noip.me" after that update, the page does not load... "Unable to connect to myaddress.noip.me" After 6-7 hours it becomes again accessible, but I'm not sure if this is normal... I think this is too much time... Please help

  Read the article

• Very slow loading pages with router

  - by user984621

  I bought new router - this one: http://www.tp-link.com/en/products/details/?model=TL-WR841ND and the problem is, that the loading pages is so slow, even sometimes the pages aren't loaded at all. Is the same, when I have on the Mac OS or Windows. Below are the informations from the router-admin section: LAN IP Address: 192.168.2.1 Subnet Mask: 255.255.255.0 WAN IP Address: 192.168.1.100 Dynamic IP Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.254 DNS Server: 89.203.178.2 , 10.14.2.1 How can I fix this problem? Is almost impossible to use the internet this way.

  Read the article

• Two routers on the same network

  - by qroberts

  My ISP has supplied me with a modem/router all in one and it isn't very good. It loses its settings and dies frequently. So I have another router in my apartment (Linksys wrt310n) that is connected to the modem via LAN-LAN port connections. I want to give my Linksys router the DHCP role and also have the ISP modem DMZ everything to the Linksys router. I want to be able to have all computers connected to both routers on the same network as well. I have been able to make it so that the Linksys has a DMZ to it from the ISP modem, but ISP modem LAN port - Linksys WAN port, so they were on different networks. Is there a way to have it so that both of them are on the same network but the Linksys router handles DHCP and port forwarding?

  Read the article

• Ubuntu Server 12.04 as a router. Problem with DNS?? Or Routing table?

  - by Lorenzo

  I have a virtualbox lab made up of 4 Windows 2008 R2 servers (DC/DNS,SQL,SHAREPOINT, EXCHANGE) that are configured with static ip addresses with NIC's attached to Internal network. Everything works. I had the requirement to execute some tests that also access external services available on the internet. To keep things clean and similar to the production environment I have installed another VM, with Ubuntu Server 12.04 64 bit and configured (I hope) to work as a router like described on this post. This VM has two network interfaces: first is Bridged with the host and is used as a WAN connection and the other one attached in the Internal Network with its own static IP address on the internal network subnet. But actually the Windows servers does not connect to the internet while the unix one connects. I did a route command. this is the result: Kernel IP Routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.69.121.1 0.0.0.0 UG 100 0 0 eth0 10.69.121.0 * 255.255.255.0 U 0 0 0 eth0 192.168.83.0 * 255.255.255.0 U 0 0 0 eth1 Can somebody help me with this configuration? :) Thanks! Addendum: I forgot to mention that one of the windows server hosts a DNS service for which I should maybe configure a forwarding server but I do not exactly know which server to forward on... :(

  Read the article

< Previous Page | 14 15 16 17 18 19 20 21 22 23 24 25  | Next Page >