Search Results

Search found 7542 results on 302 pages for 'named routing'.

Page 180/302 | < Previous Page | 176 177 178 179 180 181 182 183 184 185 186 187  | Next Page >

• VoIP setup for one external PSTN line

  - by Jcl

  I'm completely new to VoIP and the likes, and I'm trying to find information about what could be the best setup for this. I need 4 (maybe more in the future, but maximum 5 or 6) wireless extensions, connected to 1 PSTN line, and maybe 2 in the future. I've been trying to gather information about the gear needed but everything I find seems too much over-the-top (and extremely expensive). The main problem is that the physical place we are on doesn't have possibilities of having a decent internet connection, so using a external VoIP "virtual PBX" is not an option. Thing is, even if small, phone is critical to this organization. I currently have an analog DECT/GAP PBX which does what I need, however the PBX is very bad and the call quality is horrible, and that's why I want to change it. The requirements would be: 4 wireless terminals (routing cable is not an option), all of them ringing on incoming PSTN calls. Ability to do internal calls (4 separate offices) and ability to pass calls between terminals. The 4 terminals should be able to access the external PSTN line without dialing any special codes. Very important: terminals should be able to issue commands on the PSTN line to the external operator in the form *nn*nnnnnnnn# . Don't know wether this could face to be a problem, but I've had problems with analog PBX which would take any * as a PBX command and wouldn't allow terminals to send it to the external lines. Not so important, but would be nice to have: call waiting music Could anyone recommend such a setup? I need to be able to do this on a EXTREMELY LIMITED budget (that is: I don't have a limit, but all should get as much to zero as possible). I have enough spare powerful computers and a 300mbps wireless network which works just fine, so that's not to include in the budget. Don't really know if this is the best place to ask, but it's the most StackExchange-related site I've found to this subject.

  Read the article

• Basic multicast network performance problems

  - by davedavedave

  I've been using mpong from 29west's mtools package to get some basic idea of multicast latency across various Cisco switches: 1Gb 2960G, 10Gb 4900M and 10Gb Nexus N5548P. The 1Gb is just for comparison. I have the following results for ~400 runs of mpong on each switch (sending 65536 "ping"-like messages to a receiver which then sends back -- all over multicast). Numbers are latencies measured in microseconds. Switch Average StdDev Min Max 2960 (1Gb) 109.68463 0.092816 109.4328 109.9464 4900M (10Gb) 705.52359 1.607976 703.7693 722.1514 NX 5548(10Gb) 58.563774 0.328242 57.77603 59.32207 The result for 4900M is very surprising. I've tried unicast ping and I see the 4900 has ~10us higher latency than the N5548P (average 73us vs 64us). Iperf (with no attempt to tune it) shows both 10Gb switches give me 9.4Gbps line speed. The two machines are connected to the same switch and we're not doing any multicast routing. OS is RHEL 6. 10Gb NICs are HP 10GbE PCI-E G2 Dual-port NICs (I believe they are rebranded Mellanox cards). The 4900 switch is used in a project with tight access control so I'm waiting for approval before I can access it and check the config. The other two I have full access to configure. I've looked at the Cisco document[2] detailing differences between NX-OS and IOS w.r.t multicast so I've got some ideas to try out but this isn't an area where I have much expertise. Does anyone have any idea what I should be looking at once I get access to the switch? [1] http://docwiki.cisco.com/wiki/Cisco_NX-OS/IOS_Multicast_Comparison

  Read the article

• Detecting HTML5/CSS3 Features using Modernizr

  - by dwahlin

  HTML5, CSS3, and related technologies such as canvas and web sockets bring a lot of useful new features to the table that can take Web applications to the next level. These new technologies allow applications to be built using only HTML, CSS, and JavaScript allowing them to be viewed on a variety of form factors including tablets and phones. Although HTML5 features offer a lot of promise, it’s not realistic to develop applications using the latest technologies without worrying about supporting older browsers in the process. If history has taught us anything it’s that old browsers stick around for years and years which means developers have to deal with backward compatibility issues. This is especially true when deploying applications to the Internet that target the general public. This begs the question, “How do you move forward with HTML5 and CSS3 technologies while gracefully handling unsupported features in older browsers?” Although you can write code by hand to detect different HTML5 and CSS3 features, it’s not always straightforward. For example, to check for canvas support you need to write code similar to the following:   <script> window.onload = function () { if (canvasSupported()) { alert('canvas supported'); } }; function canvasSupported() { var canvas = document.createElement('canvas'); return (canvas.getContext && canvas.getContext('2d')); } </script> If you want to check for local storage support the following check can be made. It’s more involved than it should be due to a bug in older versions of Firefox. <script> window.onload = function () { if (localStorageSupported()) { alert('local storage supported'); } }; function localStorageSupported() { try { return ('localStorage' in window && window['localStorage'] != null); } catch(e) {} return false; } </script> Looking through the previous examples you can see that there’s more than meets the eye when it comes to checking browsers for HTML5 and CSS3 features. It takes a lot of work to test every possible scenario and every version of a given browser. Fortunately, you don’t have to resort to writing custom code to test what HTML5/CSS3 features a given browser supports. By using a script library called Modernizr you can add checks for different HTML5/CSS3 features into your pages with a minimal amount of code on your part. Let’s take a look at some of the key features Modernizr offers.   Getting Started with Modernizr The first time I heard the name “Modernizr” I thought it “modernized” older browsers by added missing functionality. In reality, Modernizr doesn’t actually handle adding missing features or “modernizing” older browsers. The Modernizr website states, “The name Modernizr actually stems from the goal of modernizing our development practices (and ourselves)”. Because it relies on feature detection rather than browser sniffing (a common technique used in the past – that never worked that great), Modernizr definitely provides a more modern way to test features that a browser supports and can even handle loading additional scripts called shims or polyfills that fill in holes that older browsers may have. It’s a great tool to have in your arsenal if you’re a web developer. Modernizr is available at http://modernizr.com. Two different types of scripts are available including a development script and custom production script. To generate a production script, the site provides a custom script generation tool rather than providing a single script that has everything under the sun for HTML5/CSS3 feature detection. Using the script generation tool you can pick the specific test functionality that you need and ignore everything that you don’t need. That way the script is kept as small as possible. An example of the custom script download screen is shown next. Notice that specific CSS3, HTML5, and related feature tests can be selected. Once you’ve downloaded your custom script you can add it into your web page using the standard <script> element and you’re ready to start using Modernizr. <script src="Scripts/Modernizr.js" type="text/javascript"></script>   Modernizr and the HTML Element Once you’ve add a script reference to Modernizr in a page it’ll go to work for you immediately. In fact, by adding the script several different CSS classes will be added to the page’s <html> element at runtime. These classes define what features the browser supports and what features it doesn’t support. Features that aren’t supported get a class name of “no-FeatureName”, for example “no-flexbox”. Features that are supported get a CSS class name based on the feature such as “canvas” or “websockets”. An example of classes added when running a page in Chrome is shown next:   <html class=" js flexbox canvas canvastext webgl no-touch geolocation postmessage websqldatabase indexeddb hashchange history draganddrop websockets rgba hsla multiplebgs backgroundsize borderimage borderradius boxshadow textshadow opacity cssanimations csscolumns cssgradients cssreflections csstransforms csstransforms3d csstransitions fontface generatedcontent video audio localstorage sessionstorage webworkers applicationcache svg inlinesvg smil svgclippaths"> Here’s an example of what the <html> element looks like at runtime with Internet Explorer 9:   <html class=" js no-flexbox canvas canvastext no-webgl no-touch geolocation postmessage no-websqldatabase no-indexeddb hashchange no-history draganddrop no-websockets rgba hsla multiplebgs backgroundsize no-borderimage borderradius boxshadow no-textshadow opacity no-cssanimations no-csscolumns no-cssgradients no-cssreflections csstransforms no-csstransforms3d no-csstransitions fontface generatedcontent video audio localstorage sessionstorage no-webworkers no-applicationcache svg inlinesvg smil svgclippaths">   When using Modernizr it’s a common practice to define an <html> element in your page with a no-js class added as shown next:   <html class="no-js">   You’ll see starter projects such as HTML5 Boilerplate (http://html5boilerplate.com) or Initializr (http://initializr.com) follow this approach (see my previous post for more information on HTML5 Boilerplate). By adding the no-js class it’s easy to tell if a browser has JavaScript enabled or not. If JavaScript is disabled then no-js will stay on the <html> element. If JavaScript is enabled, no-js will be removed by Modernizr and a js class will be added along with other classes that define supported/unsupported features. Working with HTML5 and CSS3 Features You can use the CSS classes added to the <html> element directly in your CSS files to determine what style properties to use based upon the features supported by a given browser. For example, the following CSS can be used to render a box shadow for browsers that support that feature and a simple border for browsers that don’t support the feature: .boxshadow #MyContainer { border: none; -webkit-box-shadow: #666 1px 1px 1px; -moz-box-shadow: #666 1px 1px 1px; } .no-boxshadow #MyContainer { border: 2px solid black; }   If a browser supports box-shadows the boxshadow CSS class will be added to the <html> element by Modernizr. It can then be associated with a given element. This example associates the boxshadow class with a div with an id of MyContainer. If the browser doesn’t support box shadows then the no-boxshadow class will be added to the <html> element and it can be used to render a standard border around the div. This provides a great way to leverage new CSS3 features in supported browsers while providing a graceful fallback for older browsers. In addition to using the CSS classes that Modernizr provides on the <html> element, you also use a global Modernizr object that’s created. This object exposes different properties that can be used to detect the availability of specific HTML5 or CSS3 features. For example, the following code can be used to detect canvas and local storage support. You can see that the code is much simpler than the code shown at the beginning of this post. It also has the added benefit of being tested by a large community of web developers around the world running a variety of browsers.   $(document).ready(function () { if (Modernizr.canvas) { //Add canvas code } if (Modernizr.localstorage) { //Add local storage code } }); The global Modernizr object can also be used to test for the presence of CSS3 features. The following code shows how to test support for border-radius and CSS transforms:   $(document).ready(function () { if (Modernizr.borderradius) { $('#MyDiv').addClass('borderRadiusStyle'); } if (Modernizr.csstransforms) { $('#MyDiv').addClass('transformsStyle'); } });   Several other CSS3 feature tests can be performed such as support for opacity, rgba, text-shadow, CSS animations, CSS transitions, multiple backgrounds, and more. A complete list of supported HTML5 and CSS3 tests that Modernizr supports can be found at http://www.modernizr.com/docs.   Loading Scripts using Modernizr In cases where a browser doesn’t support a specific feature you can either provide a graceful fallback or load a shim/polyfill script to fill in missing functionality where appropriate (more information about shims/polyfills can be found at https://github.com/Modernizr/Modernizr/wiki/HTML5-Cross-Browser-Polyfills). Modernizr has a built-in script loader that can be used to test for a feature and then load a script if the feature isn’t available. The script loader is built-into Modernizr and is also available as a standalone yepnope script (http://yepnopejs.com). It’s extremely easy to get started using the script loader and it can really simplify the process of loading scripts based on the availability of a particular browser feature. To load scripts dynamically you can use Modernizr’s load() function which accepts properties defining the feature to test (test property), the script to load if the test succeeds (yep property), the script to load if the test fails (nope property), and a script to load regardless of if the test succeeds or fails (both property). An example of using load() with these properties is show next: Modernizr.load({ test: Modernizr.canvas, yep: 'html5CanvasAvailable.js’, nope: 'excanvas.js’, both: 'myCustomScript.js' }); In this example Modernizr is used to not only load scripts but also to test for the presence of the canvas feature. If the target browser supports the HTML5 canvas then the html5CanvasAvailable.js script will be loaded along with the myCustomScript.js script (use of the yep property in this example is a bit contrived – it was added simply to demonstrate how the property can be used in the load() function). Otherwise, a polyfill script named excanvas.js will be loaded to add missing canvas functionality for Internet Explorer versions prior to 9. Once excanvas.js is loaded the myCustomScript.js script will be loaded. Because Modernizr handles loading scripts, you can also use it in creative ways. For example, you can use it to load local scripts when a 3rd party Content Delivery Network (CDN) such as one provided by Google or Microsoft is unavailable for whatever reason. The Modernizr documentation provides the following example that demonstrates the process for providing a local fallback for jQuery when a CDN is down:   Modernizr.load([ { load: '//ajax.googleapis.com/ajax/libs/jquery/1.6.4/jquery.js', complete: function () { if (!window.jQuery) { Modernizr.load('js/libs/jquery-1.6.4.min.js'); } } }, { // This will wait for the fallback to load and // execute if it needs to. load: 'needs-jQuery.js' } ]); This code attempts to load jQuery from the Google CDN first. Once the script is downloaded (or if it fails) the function associated with complete will be called. The function checks to make sure that the jQuery object is available and if it’s not Modernizr is used to load a local jQuery script. After all of that occurs a script named needs-jQuery.js will be loaded. Conclusion If you’re building applications that use some of the latest and greatest features available in HTML5 and CSS3 then Modernizr is an essential tool. By using it you can reduce the amount of custom code required to test for browser features and provide graceful fallbacks or even load shim/polyfill scripts for older browsers to help fill in missing functionality. 

  Read the article

• Internet doesn't work when enable local network

  - by rakesh yadav

  We have the following network setup: A) Router IP 192.168.51.49 B) Windows Server 2008 R2 with dual NIC: Lan A) WAN interface (192.168.51.50) ( Used for internet) Lan B) LAN interface (192.168.30.228) ( used for local connectivity ) When I keep both LAN Enabled than my internet doesn't work, but if I disable my local LAN then internet works fine. How can I resolve this issue? Do I need to do routing on my server Please find the below attached route print result C:\Users\Administrator>route print =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.51.49 192.168.51.50 276 0.0.0.0 0.0.0.0 192.168.30.227 192.168.30.228 266 192.168.30.224 255.255.255.240 On-link 192.168.30.228 266 192.168.30.228 255.255.255.255 On-link 192.168.30.228 266 192.168.30.239 255.255.255.255 On-link 192.168.30.228 266 192.168.51.48 255.255.255.240 On-link 192.168.51.50 276 192.168.51.50 255.255.255.255 On-link 192.168.51.50 276 192.168.51.63 255.255.255.255 On-link 192.168.51.50 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 202.56.230.5 255.255.255.255 192.168.51.49 192.168.51.50 21 202.56.230.6 255.255.255.255 192.168.51.49 192.168.51.50 21 192.168.26.124 255.255.255.255 192.168.51.49 192.168.51.50 21 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.51.50 276 224.0.0.0 240.0.0.0 On-link 192.168.30.228 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.51.50 276 255.255.255.255 255.255.255.255 On-link 192.168.30.228 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.30.227 Default 0.0.0.0 0.0.0.0 192.168.51.49 Default ===========================================================================

  Read the article

• How have multiple web servers and IPs on the same physical network

  - by jsigned

  I do web development out of a small office and need to have multiple physical and virtual servers that can be accessed from the internet. I also have a number of devices (computers, laptops, tablets, printers, etc) that need connections as well. I have gotten a subnet of 8 IP's from my ISP and while that is adequate for the web servers its far too small for everything that needs access to the network. My router is an ASUS RT-N16 running DD-WRT. I'm just smart enough about this routing topic to be dangerous, think 2 year old with a magic marker. I would like to keep my internal network NAT'ed on the 192.168.x.x network and route the 68.69.x.x 255.255.255.248 traffic directly to the servers. The physical network consists of the 4 port DD-WRT router and an unmanaged gig switch. I have a fiber connection to the office that works as an Ethernet port. In other words I can plug my laptop directly into it and have access to the internet. There is no login or password and the router is setup to get DHCP from the ISP, and to provide DHCP addresses for the internal network. What I've done so far is google and try different configurations with little success. In the end I decided I didn't even know how to ask the questions needed. My questions are: Is this the best way to configure the network? How do you do it? VLANs? Multiple routers? I've never had to configure a router using anything more than the GUI so if this is command line stuff be gentle.

  Read the article

• Windows 8 - no internet connetction to some hosts while VPN is active

  - by HTD

  I use VPN to access the servers at work. When VPN is used, all network traffic to the Internet passes through my company network. It worked without any problems on Windows 7, now on Windows 8 some sites suddenly became inaccessible. Please note - I don't try to connect them over RDP, they are public Internet addresses, outside company network. They are inaccessible using any protocol. Ping returns "General failure.". I know it could be a misconfiguration on my company's server side, but it's very strange, since the same VPN connection used on Windows 7 works properly. What's wrong? Is it a Windows 8 bug, or is there something I could do on my company servers to make VPN work as expected with Windows 8? My company network works on Windows Server 2008 R2 and uses Microsoft TMG firewall. I couldn't find any rules blocking the traffic to mentioned sites, all network traffic for VPN users are passed through for all IPs and protocols. Any clues? UDPATE: Important - one whole day it worked. I hibernated and restarted the computer, connected and disconnected VPN - nothing could break my connection. Today it broke again, and restarting Windows didn't help. And now the solution: route add -p 0.0.0.0 MASK 255.255.255.255 192.168.1.1 Oh, OK, I know what it did, added my default gateway to routing table. But it still didn't work sometimes. So I removed my main network gateway route with: route delete -p 0.0.0.0 MASK 0.0.0.0 192.168.0.1 And added modified with: route add -p 0.0.0.0 MASK 255.255.255.255 192.168.0.1 And it works. Now. But I don't trust this. I don't know what really happened.

  Read the article

• Server 2008 NAT Internet Not Working

  - by Jack

  I'm trying to set up Routing and Remote Access on Windows Server 2008 R2, I have a network connection that I want to share the internet from to another private network. The server has two NICs which are configured as follows: External NIC (Dynamically assigned by ISP) IP:10.175.4.150 Subnet:255.255.192.0 Gateway:10.175.0.1 DNS:10.175.0.1 Internal NIC IP:172.16.254.1 Subnet:255.255.255.0 Gateway:None DNS:None I have set the external NIC to be the public interface and enabled NAT on it in the RRAS MMC and set the internal NIC to be a private interface. I have also set up the DNS forwarding or whatever it is in the NAT section. From a client (IP:172.16.254.2) I can ping the server and access files on it, when I try to browse the web with the default gateway set to the internal NIC ip I end up getting a 404 page which is returned from the ISPs default gateway. I'm guessing it's something to do with the double NAT possibly. Trying to ping the ISPs default gateway from a private network client just times out as does accessing it directly. I've disabled and reconfigured RRAS multiple times and that doesn't seem to have made a difference, so can anyone tell me what I'm doing wrong? Thanks.

  Read the article

• CodePlex Daily Summary for Thursday, June 09, 2011

  CodePlex Daily Summary for Thursday, June 09, 2011Popular ReleasesNetOffice - The easiest way to use Office in .NET: NetOffice Release 0.9: Changes: - fix examples (include issue 16026) - add new examples - 32Bit/64Bit Walkthrough is now available in technical Documentation. Includes: - Runtime Binaries and Source Code for .NET Framework:......v2.0, v3.0, v3.5, v4.0 - Tutorials in C# and VB.Net:..............................................................COM Proxy Management, Events, etc. - Examples in C# and VB.Net:............................................................Excel, Word, Outlook, PowerPoint, Access - COMAddi...Reusable Library: V1.1.3: A collection of reusable abstractions for enterprise application developerDevpad: 0.4: Whats new for Devpad 0.4: New JavaScript support New Options dialog Minor Bug Fix's, improvements and speed upsClosedXML - The easy way to OpenXML: ClosedXML 0.54.0: New on this release: 1) Mayor performance improvements. 2) AdjustToContents now take into account the text rotation. 3) Fixed issues 6782, 6784, 6788HTML-IDEx: HTML-IDEx .15 ALPHA: This release fixes line counting a little bit and adds the masshighlight() sub, which highlights pasted and inserted code.AutoLoL: AutoLoL v2.0.3: - Improved summoner spells are now displayed - Fixed some of the startup errors people got - Double clicking an item selects it - Some usability changes that make using AutoLoL just a little easier - Bug fixes AutoLoL v2 is not an update, but an entirely new version! Please install to a different directory than AutoLoL v1VidCoder: 0.9.2: Updated to HandBrake 4024svn. This fixes problems with mpeg2 sources: corrupted previews, incorrect progress indicators and encodes that incorrectly report as failed. Fixed a problem that prevented target sizes above 2048 MB.SharePoint Search XSL Samples: SharePoint 2010 Samples: I have updated some of the samples from the 2007 release. These all work in SharePoint 2010. I removed the Pivot on File Extension because SharePoint 2010 search has refiners that perform the same function.Fingertip detection via OpenNI: Fingertip Detection 1.0.0.0: This release will allow you to recognize fingertips. To do that shake you hand, after pressing button. Known Issues : 1. When your hand is near to some objects, recognition is not working very well 2. When you hand is far away from sensor, recognition is not working very wellAcDown????? - Anime&Comic Downloader: AcDown????? v3.0 Beta5: ??AcDown?????????????，??????????????，????、????。?????Acfun????? ????32??64? Windows XP/Vista/7 ????????????? ??：????????Windows XP???,?????????.NET Framework 2.0???(x86)?.NET Framework 2.0???(x64)，?????"?????????"??? ??v3.0 Beta5 ?????????? ???? ?? ???????? ???"????????"?? ????????????? ????????/???? ?? ???"????"??? ?? ??????????? ?? ?? ??????????? ?? ?????????????????? ??????????????????? ???????????????? ????????????Discussions???????? ????AcDown??????????????VFPX: GoFish 4 Beta 1: Current beta is Build 144 (released 2011-06-07 ) See the GoFish4 info page for details and video link: http://vfpx.codeplex.com/wikipage?title=GoFishSharePoint 2010 FBA Pack: SharePoint 2010 FBA Pack 1.0.3: Fixed User Management screen when "RequiresQuestionAndAnswer" set to true Reply to Email Address can now be customized User Management page now only displays users that reside in the membership database Web parts have been changed to inherit from System.Web.UI.WebControls.WebParts.WebPart, so that they will display on anonymous application pages For installation and configuration steps see here.SizeOnDisk: 1.0.8.2: With installerTerrariViewer: TerrariViewer v2.5: Added new items associated with Terraria v1.0.3 to the character editor. Fixed multiple bugs with Piggy Bank EditorySterling NoSQL OODB for .NET 4.0, Silverlight 4 and 5, and Windows Phone 7: Sterling OODB v1.5: Welcome to the Sterling 1.5 RTM. This version is backwards compatible without modification to the 1.4 beta. For the 1.0, you will need to upgrade your database. Please see this discussion for details. You must modify your 1.0 code for persistence. The 1.5 version defaults to an in-memory driver. To save to isolated storage or use one of the new mechanisms, see the available drivers and pass an instance of the appropriate one to your database (different databases may use different drivers). ...EnhSim: EnhSim 2.4.6 BETA: 2.4.6 BETAThis release supports WoW patch 4.1 at level 85 To use this release, you must have the Microsoft Visual C++ 2010 Redistributable Package installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=A7B7A05E-6DE6-4D3A-A423-37BF0912DB84 To use the GUI you must have the .NET 4.0 Framework installed. This can be downloaded from http://www.microsoft.com/downloads/en/details.aspx?FamilyID=9cfb2d51-5ff4-4491-b0e5-b386f32c0992 - Added in the proper...Grammar and Spell Checking Plugin for Windows Live Writer: Grammar Checker Plugin v1.0: First version of the grammar checker plugin for Windows Live Writer. You can show your appreciation for this plugin and support further development by donating via PayPal. Any amount will be appreciated. Thank you. Donatepatterns & practices: Project Silk: Project Silk Community Drop 10 - June 3, 2011: Changes from previous drop: Many code changes: please see the readme.mht for details. New "Application Notifications" chapter. Updated "Server-Side Implementation" chapter. Guidance Chapters Ready for Review The Word documents for the chapters are included with the source code in addition to the CHM to help you provide feedback. The PDF is provided as a separate download for your convenience. Installation Overview To install and run the reference implementation, you must perform the fol...Claims Based Identity & Access Control Guide: Release Candidate: Highlights of this release This is the release candidate drop of the new "Claims Identity Guide" edition. In this release you will find: All code samples, including all ACS v2: ACS as a Federation Provider - Showing authentication with LiveID, Google, etc. ACS as a FP with Multiple Business Partners. ACS and REST endpoints. Using a WP7 client with REST endpoints. All ACS specific chapters. Two new chapters on SharePoint (SSO and Federation) All revised v1 chapters We are now ...Terraria Map Generator: TerrariaMapTool 1.0.0.4 Beta: 1) Fixed the generated map.html file so that the file:/// is included in the base path. 2) Added the ability to use parallelization during generation. This will cause the program to use as many threads as there are physical cores. 3) Fixed some background overdraw.New ProjectsAlumni Association Website Centre: We named our project 'MCIS - Ma Chung Information System Association Centre'. This project is only simulation for us to try building a complex website that have functional features.ASP.NET without ClientID's: Render ASP.NET Controls without ClientID - reduce HTML output responseBLPImage: .BLP files are texture files used in games made by Blizzard Entertainment, also used in other games like Neverwinter Nights.Breaker Dev IRC Client: Breaker Dev IRC is just another IRC client that's Open source.Cloud Upload: CloudUpload shows how to use Shared Access Signatures to upload, download, delete and list blobs in a Azure Storage container. Using shared acces signatures permits to partition a storage account and NOT to use the storage shared key in the application. The project uses REST API.Clounter, count how many lines you have coded: A tiny, small, lightweight, ultra simple app to count how many lines of code you have programmed so far. Or hoe many lines of anything there's on a folder. You can filter by directory and by file extension.Color picker control for Silverlight: Color picker is a custom Silverlight control that makes it easy to add color picking functionality to the Silverlight projects.CommonSample: a code sampleCompactMapper: A simple object/relational mapper for the Compact Framework. Based on attributes and supporting SQLite Tracker https://www.pivotaltracker.com/projects/303523dbkk101 hello codeplex: Trying out ClickOnce deployment/updatesDesktop Browser: Web based file explorer, runs locally on your browser, designed for media desktops.EFMagic: EFMagic is a library based on Entity Framework 4.1 that manage the schema of your database, automatically generates sql script to update your database and generate with Code First your schema.EWF_Install: Installs EWF (Enhanced Write Filter) in Windows XP without hassle. Changes system settings, accordingly to EWF characteristics. Extreme Download: Projeto desenvolvido no tempo livre para auxiliar a gerenciar download de vários arquivos.Flac2Wav: Converts FLAC file into WAV. Example of using libFLAC.dll in C#.Flac2Wma: Converts FLAC files into lossless WMA files. Uses libFLAC.dll, taglib-sharp.dll, MediaInfo32.dll. Converts directory tree, with only one click. Retains information from Tags.GeoMedia PostGIS data server: GeoMedia PostGIS data server is a GDO (Geographic Database Object) component that enables read and write to a Postgre/PostGIS database from Intergraph GeoMedia product family.Google Page Speed for .Net: This little piece of software sends a request to the Google page speed API, then parses the JSON response and presents them in a nice class. I use this class on this webpage to show the page speed score at the bottom right corner of my site: http://schaffhauser.meHubLog: Tool for application administrator: collects and joins logs from multiple instances of an application, and displays them. Example of usage in C#: the telnet protocol, dynamically compiled functions as elements of configuration.hydrodesktop2: HydroDesktop is a free and open source desktop application developed in C# .NET that serves as a client for CUAHSI HIS WaterOneFlow web services data and includes data discovery, download, visualization, editing, and integration with other analysis and modeling tools. ImageResizing.Net: Makes resizing and cropping images easy and fast - just change the URL. Mature and popular HttpModule for ASP.NET and IIS. Works great with jQuery, jCrop, Galleria, and and can be easily integrated into any CMS.License Header Manager for Visual Studio: Automatically insert license headers into your source code files in Visual Studio.Ma Chung Voice website: Ma Chung University website project. created by Yogi Rinaldi & Irfan using ASP.NET Ma Chung University, Indonesia.MCFC Futsal Machung Malang Indonesia: Websites We discuss the sport of futsal. Here we make in such a way that can be accessed easily by the user. please try.Mp3Cleaner: Mp3Cleaner is used to "clean up" and organize the music files external and internal (tags) information. Despite the name, supports most types of music files (flac, wma, wav .... ogg, …), it uses the tagLib library.MSBuild CI Tasks: Provides MSBuild utility tasks for continuous integration. NetMemory: let us remember ancestor better!nhibernate of mvcmusicstore: convert by http://mvcmusicstore.codeplex.com/ ·Shows data access via nhibernate & fluent tool: ·http://nmg.codeplex.com/ demo:http://www.pcme.info Parallelminds Asp.net Web Parts Demo Code: This is Asp.net web part demo code by www.parallelminds.biz to help new developers, community understand what are Asp.net web parts and how to use it for various purposes.This will continue exploring more asp.net related web parts functionality.PivotalTrackerAgent: Pivotal Tracker Agent provides ways to update your projects on PivotalTracker.com. Your developers will no longer have to update it through its web-based GUI if you incorporate it with your event handler of source control and/or bug tracking system.Programa voluntario: Sistema de gerenciamento de instituições e voluntáriosRaytracer for fun: Simple raytracingengine written for fun.SCOPE PHOTOGRAPHY MA CHUNG INDONESIA: This website contains a collection of people who hobby photography. We can shared photo and shared more info about photography. And we can give a comment in other member photo galery. Look and Join us. sqlscriptmover: Exports stored procedures, function, views, tables and triggers to individual files or imports same and attempts to create in designated database.UKM MA CHUNG FUTSAL: This Website Created to all of Ma Chung Student for develop his talent of futsal especially with user friendly interfaceVideoStreamer Iphone/Ipad: Video streamer that support single Range. it will handle video streaming especially MP4, for iphone and ipadVolleyExtracurriculer: We named our project 'UMC Information System Volley Extracurricular’. It doesn't mean this project is really used to be official website for volley extracurricular in our campus, but it only simulation for us to tried to built one complex website.Web Gozar Manager: HI

  Read the article

• Avoiding DNS timeouts when a dns server fails

  - by Neil Katin

  We have a small datacenter with about a hundred hosts pointing to 3 internal dns servers (bind 9). Our problem comes when one of the internal dns servers becomes unavailable. At that point all the clients that point to that server start performing very slowly. The problem seems to be that the stock linux resolver doesn't really have the concept of "failing over" to a different dns server. You can adjust the timeout and number of retries it uses, (and set rotate so it will work through the list), but no matter what settings one uses our services perform much more slowly if a primary dns server becomes unavailable. At the moment this is one of the largest sources of service disruptions for us. My ideal answer would be something like "RTFM: tweak /etc/resolv.conf like this...", but if that's an option I haven't seen it. I was wondering how other folks handled this issue? I can see 3 possible types of solutions: Use linux-ha/Pacemaker and failover ips (so the dns IP VIPs are "always" available). Alas, we don't have a good fencing infrastructure, and without fencing pacemaker doesn't work very well (in my experience Pacemaker lowers availability without fencing). Run a local dns server on each node, and have resolv.conf point to localhost. This would work, but it would give us a lot more services to monitor and manage. Run a local cache on each node. Folks seem to consider nscd "broken", but dnrd seems to have the right feature set: it marks dns servers as up or down, and won't use 'down' dns servers. Any-casting seems to work only at the ip routing level, and depends on route updates for server failure. Multi-casting seemed like it would be a perfect answer, but bind does not support broadcasting or multi-casting, and the docs I could find seem to suggest that multicast dns is more aimed at service discovery and auto-configuration rather than regular dns resolving. Am I missing an obvious solution?

  Read the article

• Cisco router not receiving OSPF updates

  - by WebDevHobo

  Or at least, that's what I think is happening. There doesn't appear to be a debug command for this, or to see if something is in the routing table. I'm testing out this setup in Packet Tracer. I have 3 routers and a webserver From left to right, you have: Webserver - Router1 - Router2 - Router3 Router1 and Router2 can succesfully ping WebServer. Router3 cannot. Router2 has a default gateway set, to send all not-recognized data through its serial interface to Router1. Like this: ip route 0.0.0.0 0.0.0.0 Serial 0/0/1 Serial 0/0/1 being the connection to Router1 Router2 and Router3 have OSPF configured. From their "show run": Router2: router ospf 1 log-adjacency-changes passive-interface Serial0/0/1 network 10.1.1.0 0.0.0.3 area 0 default-information originate ! Router3: router ospf 1 log-adjacency-changes network 10.1.1.0 0.0.0.3 area 0 passive-interface FastEthernet0/0 ! I was under the assumption that setting default-information originate on Router2 would give Router3 the needed information. What's going wrong here? The interfaces are up. Ip addresses are with mask-range, clock rate is set at correct end. I don't know what else to check.

  Read the article

• Cannot ping Google Public DNS on 8.8.8.8

  - by Tibor

  I have a weird problem on my Windows 7 (x64) computer. I seem to cannot ping the Google Public DNS on one of its addresses (while the other works fine). The peculiar thing is that it fails with the General failure. error message which usually means that there is a problem with a network adapter/base connectivity and not a timeout as one would expect. I checked my routing tables for any anomalies and I even flushed them but the problem seems unrelated. All the other hosts I tried ping fine (either respond or timeout). If I try to tracert or connect to the address via browser (yes, I know that it doesn't listen on port 80), it also fails instantaneously. The reason I need to ping 8.8.8.8 is that I commonly use it as a test of Internet conectivity due to it being rememberable. The problem occurs no matter where I connect to the Internet (it is a laptop computer). What could be the cause of this anomaly? Note: I use native IPv6 connectivity.

  Read the article

• Amazon VPC NAT not working

  - by rpkelly

  I'm trying to create a NAT instance for my VPC to allow instances on private subnets connect to the internet (most importantly, S3). I tried following the instructions here: http://docs.amazonwebservices.com/AmazonVPC/2011-07-15/UserGuide/index.html?VPC_NAT_Instance.html . Unfortunately, the instances in the private subnet (call it 10.10.2.0/24) cannot reach the internet. I have done the following: Create a NAT instance (Amazon's ami-vpc-nat-1.0.0-beta.i386-ebs (ami-d8699bb1)) in public subnet (call it 10.10.1.0/24). Changed "Source / Dest Check" to disabled. Created a new entry in the default routing table (which is used by 10.10.2.0/24) and had it point to the ID of the newly created instance. Associated an Elastic IP address with the NAT instance. Allowed all outbound traffic on the security group of the NAT instance. Ensured that all traffic could pass between the two subnets. I've tried also doing this with an existing instance using iptables, but had no luck. And I have verified that sys.net.ipv4.ip_forward is 1, just in case anyone was wondering. And I still have no internet connectivity from the instances on 10.10.2.0/24. Does anyone have any suggestions?

  Read the article

• How to set up a VPN Incoming connection with Windows to tunnel Internet traffic?

  - by Mehrdad

  I want to set up a VPN on a remote server to route all my Internet traffic for privacy reasons. I can set up an incoming connection and connect to it successfully. The problem is, I can just see the remote computer and no other Web sites will open. I want the remote server to act like a NAT. How can I do that? Note that I don't want to split Internet traffic. I actually want to send all the traffic to the remote server but need to make it relay the traffic. For the record, my remote server is Windows Web Server 2008 which does not have routing and remote access service. Clarification I'm mostly interested in server configuration. I don't have any problems configuring the client. By the way, Windows Web Server 2008 seems to have the same VPN features built in client OSes (like Vista) and specifically, it doesn't include the RRAS console in MMC. I'm also open to suggestions regarding third party PPTP/L2TP daemons available, if they are free.

  Read the article

• Two hosted servers, one public - VPN?

  - by Aquitaine

  Hello there, Web developer here who has to occasionally wear a system & network admin hat (small company). We currently have a single hosted server running Windows Server 2003 that runs both our web server (IIS/Coldfusion) and our database server (SQL Server 2008). We lock down the SQL server by allowing only specific IPs to connect to it. Not ideal but it's worked thus far. We're moving up to two distinct servers and I want to take the opportunity to 'get things right' and make only the web server face the public. What I need to be able to do is to allow only a handful of people to connect to the database server. Rather than using an IP allow list, I'd prefer to use a VPN to let people through so that access is based on the user and not simply the user's location. I'm leaning toward something like OpenVPN, just so I can stick with Server 2008 Web edition. Do I: Use the web server as a VPN server and set up the database server to only accept connections from the web server? Is there an extra step required to make connections to, say, db.mycompany.com route through the VPN rather than through a different connection? I'm ignorant of this part of network infrastructure stuff. Or, Set up a VPN server on the database server as the only public-facing server connection so that there aren't any routing issues to deal with? I know this is Network 101 stuff but I thought I'd ask before just blundering through it since it could affect the company a bit. Thanks very much!

  Read the article

• Adding a Second Wireless Router to an Existing Wired Network

  - by KVCrawford

  I apologize ahead of time, I know this has been asked before, but I'm still having problems...maybe you guys can help. I started out with the basic instructions from the highest-voted answer at http://serverfault.com/questions/41572/adding-a-second-wireless-router-to-my-network The new Wireless router in question is a Linksys Wireless-N Gigabit Router, Model # WRT310N Here are the steps I've taken in setting it up: Plug my laptop into LAN port #2 in the new router. Nothing else is connected at this point Configure the new router to be 192.168.1.200 (the original router is 192.168.1.1, and its DHCP clients are from 192.168.1.100-x.x.x.199) Set the internet connection on the new router to "DHCP Client" Turn off the DHCP server & NAT routing on the new router Plug in a LAN cable from the original router into the LAN port #1 on the new router (NOT the WAN port, nothing is plugged in there) Reset the new router Afterwards, I try to ping 192.168.1.1 from the laptop plugged into LAN port #2 on the new router, with no response. 192.168.1.200 garners no response either. Typing "ipconfig" tells me: Autoconfiguration IP Address: 169.254.198.113 Subnet Mask: 255.255.0.0 Default Gateway: 169.254.198.113 What's going wrong? I appreciate any help!

  Read the article

• Appears to be "randomly" switching between the acl matched backend and the default backend

  - by Xoor

  I have HAProxy acting as a proxy in front of: An NGinx instance An in-house load balancer in front of multiple dynamic services exposed with socket.io (websockets) My problem is that from time to time my connections are proxied correctly to my socket.io cluster, and then randomly it fallsback to routing to NGinx which obviously is annoying and meaningless since NGinx isn't mean't to handle the request. This happens when requesting for URLs of the format : http://mydomain.com/backends/* There's an ACL in the HAProxy config to match the '/backends/*' path. Here's a simplified version of my HAProxy config (removed extra unrelated entries and changed names): global daemon maxconn 4096 user haproxy group haproxy nbproc 4 defaults mode http timeout server 86400000 timeout connect 5000 log global #this frontend interface receives the incoming http requests frontend http-in mode http #process all requests made on port 80 bind *:80 #set a large timeout for websockets timeout client 86400000 # Default Backend default_backend www_backend # Loadfire (socket cluster) acl is_loadfire_backends path_beg /backends use_backend loadfire_backend if is_loadfire_backends # NGinx backend backend www_backend server www_nginx localhost:12346 maxconn 1024 # Loadfire backend backend loadfire_backend option forwardfor # This sets X-Forwarded-For option httpclose server loadfire localhost:7101 maxconn 2048 It's really quite confusing for me why the behaviour appears to be "random", since being hard to reproduce it's hard to debug. I appreciate any insight on this.

  Read the article

• SharePoint Records Center Submitted E-mail Records not picked up

  - by Kenneth Verburg

  We have set up a new SharePoint 2007 site with a Records Repository. We're using Exchange 2007 Managed Folders to route e-mails to this repository based on the 'label' attached to the e-mail as set in the Exchange 2007 journaling options. E-mails added to a Managed Folder get sent to SharePoint, they end up in the "Submitted E-mail Records" list of the Records Repository. That's according to plan, but the e-mails are not routed to the respective document library as defined by the label. Instead an error appears in the event viewer for every e-mail listed in the Submitted E-mail Records list, on every interval of the records repository schedule (set to every two minutes for testing purposes): Value cannot be null, parameter name: g. Sending a document from the SharePoint site iself to the Records Repository via the Send To... link works fine, but e-mails get stuck in the list... We have set Document Libraries in the Respository with and without content types (with matching names with the Label and the Record Routing rule set). Any ideas what could be wrong? This is in the event log: Every two minutes the following error appears in the Application Log: Source: Office SharePoint Server Category: Records Center Type: Error Event ID: 4975 User: N/A Computer: SPS2007 Description: Value cannot be null. Parameter name: g For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• mod_rewrite REQUEST_FILENAME doesn't contain absolute path

  - by Paul Dixon

  I have a problem with a file test operation in a mod_rewrite RewriteCond entry which is testing whether %{REQUEST_FILENAME} exists. It seems that rather than %{REQUEST_FILENAME} being an absolute path, I'm getting a path which is rooted at the DocumentRoot instead. Configuration I have this inside a <VirtualHost> block in my apache 2.2.9 configuration: RewriteEngine on RewriteLog /tmp/rewrite.log RewriteLogLevel 5 #push virtually everything through our dispatcher script RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^/([^/]*)/?([^/]*) /dispatch.php?_c=$1&_m=$2 [qsa,L] Diagnostics attempted That rule is a common enough idiom for routing requests for non-existent files or directories through a script. Trouble is, it's firing even if a file does exist. If I remove the rule, I can request normal files just fine. But with the rule in place, these requests get directed to dispatch.php Rewrite log trace Here's what I see in the rewrite.log init rewrite engine with requested uri /test.txt applying pattern '^/([^/]*)/?([^/]*)' to uri '/test.txt' RewriteCond: input='/test.txt' pattern='!-f' => matched RewriteCond: input='/test.txt' pattern='!-d' => matched rewrite '/test.txt' -> '/dispatch.php?_c=test.txt&_m=' split uri=/dispatch.php?_c=test.txt&_m= -> uri=/dispatch.php, args=_c=test.txt&_m= local path result: /dispatch.php prefixed with document_root to /path/to/my/public_html/dispatch.php go-ahead with /path/to/my/public_html/dispatch.php [OK] So, it looks to me like the REQUEST_FILENAME is being presented as a path from the document root, rather than the file system root, which is presumably why the file test operator fails. Any pointers for resolving this gratefully received...

  Read the article

• how does a computer know which IP address will route information to the internet? [closed]

  - by JohnMerlino

  Possible Duplicate: How does IPv4 Subnetting Work? For example, I have a computer with a Network Inteface Card (NIC) which is an Ethernet card that is connected by Ethernet cables to a router. There is also another computer with a cable that is connected in another port of the router. This is a Belkin router operating over an Ethernet in the LAN. When I connect to serverfault.com, it maps to an IP address. My computer now has a task of connecting to that IP address. But my computer itself cannot connect to the serverfault IP address. Only the router can. So the task of my computer is to find the IP address associated with the node that will do the routing to the public internet. How does my computer know that a particular IP address in the local network belongs to the router, and is not another computer connected to the network? Is this information configured manually in the operating system itself? Somehow my computer must know that it must send ethernet frames to the router with the expectation that the router will then send the packet to a public IP. How does it know to send it to the router? Is the router's ip address stored in my computer like a key/value pair e.g. "router"="192.168.2.6", so that when I put a public ip address, my computer first knows to connect to 192.168.2.6?

  Read the article

• Solaris 10: cannot ping to/from server

  - by anurag kohli

  All, I have a Solaris 10 server which is not reachable by IP (ie can't ping to/from the server). I believe I have the default route setup correctly. See below: # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 192.168.62.100 netmask ffffff00 broadcast 192.168.62.255 ether 0:14:4f:b1:9b:30 # netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref Use Interface -------------------- -------------------- ----- ----- ------ --------- 192.168.62.0 192.168.62.100 U 1 40 bge0 224.0.0.0 192.168.62.100 U 1 0 bge0 default 192.168.62.1 UG 1 0 127.0.0.1 127.0.0.1 UH 1 4 lo0 # # cat /etc/defaultrouter 192.168.62.1 I have verified layer1 and layer 2 are up on the switchport, and that it's on the correct VLAN. I have also checked the default gateawy (192.168.62.1) is in fact reachable since I can ping it from my PC: Pinging 192.168.62.1 with 32 bytes of data: Reply from 192.168.62.1: bytes=32 time=1ms TTL=254 Reply from 192.168.62.1: bytes=32 time=1ms TTL=254 Reply from 192.168.62.1: bytes=32 time=3ms TTL=254 Reply from 192.168.62.1: bytes=32 time=6ms TTL=254 I'm at a loss as to what is wrong. I would highly appreciated your assistance. Thank you very much.

  Read the article

• Detecting HTML5/CSS3 Features using Modernizr

  - by dwahlin

  HTML5, CSS3, and related technologies such as canvas and web sockets bring a lot of useful new features to the table that can take Web applications to the next level. These new technologies allow applications to be built using only HTML, CSS, and JavaScript allowing them to be viewed on a variety of form factors including tablets and phones. Although HTML5 features offer a lot of promise, it’s not realistic to develop applications using the latest technologies without worrying about supporting older browsers in the process. If history has taught us anything it’s that old browsers stick around for years and years which means developers have to deal with backward compatibility issues. This is especially true when deploying applications to the Internet that target the general public. This begs the question, “How do you move forward with HTML5 and CSS3 technologies while gracefully handling unsupported features in older browsers?” Although you can write code by hand to detect different HTML5 and CSS3 features, it’s not always straightforward. For example, to check for canvas support you need to write code similar to the following:   <script> window.onload = function () { if (canvasSupported()) { alert('canvas supported'); } }; function canvasSupported() { var canvas = document.createElement('canvas'); return (canvas.getContext && canvas.getContext('2d')); } </script> If you want to check for local storage support the following check can be made. It’s more involved than it should be due to a bug in older versions of Firefox. <script> window.onload = function () { if (localStorageSupported()) { alert('local storage supported'); } }; function localStorageSupported() { try { return ('localStorage' in window && window['localStorage'] != null); } catch(e) {} return false; } </script> Looking through the previous examples you can see that there’s more than meets the eye when it comes to checking browsers for HTML5 and CSS3 features. It takes a lot of work to test every possible scenario and every version of a given browser. Fortunately, you don’t have to resort to writing custom code to test what HTML5/CSS3 features a given browser supports. By using a script library called Modernizr you can add checks for different HTML5/CSS3 features into your pages with a minimal amount of code on your part. Let’s take a look at some of the key features Modernizr offers.   Getting Started with Modernizr The first time I heard the name “Modernizr” I thought it “modernized” older browsers by added missing functionality. In reality, Modernizr doesn’t actually handle adding missing features or “modernizing” older browsers. The Modernizr website states, “The name Modernizr actually stems from the goal of modernizing our development practices (and ourselves)”. Because it relies on feature detection rather than browser sniffing (a common technique used in the past – that never worked that great), Modernizr definitely provides a more modern way to test features that a browser supports and can even handle loading additional scripts called shims or polyfills that fill in holes that older browsers may have. It’s a great tool to have in your arsenal if you’re a web developer. Modernizr is available at http://modernizr.com. Two different types of scripts are available including a development script and custom production script. To generate a production script, the site provides a custom script generation tool rather than providing a single script that has everything under the sun for HTML5/CSS3 feature detection. Using the script generation tool you can pick the specific test functionality that you need and ignore everything that you don’t need. That way the script is kept as small as possible. An example of the custom script download screen is shown next. Notice that specific CSS3, HTML5, and related feature tests can be selected. Once you’ve downloaded your custom script you can add it into your web page using the standard <script> element and you’re ready to start using Modernizr. <script src="Scripts/Modernizr.js" type="text/javascript"></script>   Modernizr and the HTML Element Once you’ve add a script reference to Modernizr in a page it’ll go to work for you immediately. In fact, by adding the script several different CSS classes will be added to the page’s <html> element at runtime. These classes define what features the browser supports and what features it doesn’t support. Features that aren’t supported get a class name of “no-FeatureName”, for example “no-flexbox”. Features that are supported get a CSS class name based on the feature such as “canvas” or “websockets”. An example of classes added when running a page in Chrome is shown next:   <html class=" js flexbox canvas canvastext webgl no-touch geolocation postmessage websqldatabase indexeddb hashchange history draganddrop websockets rgba hsla multiplebgs backgroundsize borderimage borderradius boxshadow textshadow opacity cssanimations csscolumns cssgradients cssreflections csstransforms csstransforms3d csstransitions fontface generatedcontent video audio localstorage sessionstorage webworkers applicationcache svg inlinesvg smil svgclippaths"> Here’s an example of what the <html> element looks like at runtime with Internet Explorer 9:   <html class=" js no-flexbox canvas canvastext no-webgl no-touch geolocation postmessage no-websqldatabase no-indexeddb hashchange no-history draganddrop no-websockets rgba hsla multiplebgs backgroundsize no-borderimage borderradius boxshadow no-textshadow opacity no-cssanimations no-csscolumns no-cssgradients no-cssreflections csstransforms no-csstransforms3d no-csstransitions fontface generatedcontent video audio localstorage sessionstorage no-webworkers no-applicationcache svg inlinesvg smil svgclippaths">   When using Modernizr it’s a common practice to define an <html> element in your page with a no-js class added as shown next:   <html class="no-js">   You’ll see starter projects such as HTML5 Boilerplate (http://html5boilerplate.com) or Initializr (http://initializr.com) follow this approach (see my previous post for more information on HTML5 Boilerplate). By adding the no-js class it’s easy to tell if a browser has JavaScript enabled or not. If JavaScript is disabled then no-js will stay on the <html> element. If JavaScript is enabled, no-js will be removed by Modernizr and a js class will be added along with other classes that define supported/unsupported features. Working with HTML5 and CSS3 Features You can use the CSS classes added to the <html> element directly in your CSS files to determine what style properties to use based upon the features supported by a given browser. For example, the following CSS can be used to render a box shadow for browsers that support that feature and a simple border for browsers that don’t support the feature: .boxshadow #MyContainer { border: none; -webkit-box-shadow: #666 1px 1px 1px; -moz-box-shadow: #666 1px 1px 1px; } .no-boxshadow #MyContainer { border: 2px solid black; }   If a browser supports box-shadows the boxshadow CSS class will be added to the <html> element by Modernizr. It can then be associated with a given element. This example associates the boxshadow class with a div with an id of MyContainer. If the browser doesn’t support box shadows then the no-boxshadow class will be added to the <html> element and it can be used to render a standard border around the div. This provides a great way to leverage new CSS3 features in supported browsers while providing a graceful fallback for older browsers. In addition to using the CSS classes that Modernizr provides on the <html> element, you also use a global Modernizr object that’s created. This object exposes different properties that can be used to detect the availability of specific HTML5 or CSS3 features. For example, the following code can be used to detect canvas and local storage support. You can see that the code is much simpler than the code shown at the beginning of this post. It also has the added benefit of being tested by a large community of web developers around the world running a variety of browsers.   $(document).ready(function () { if (Modernizr.canvas) { //Add canvas code } if (Modernizr.localstorage) { //Add local storage code } }); The global Modernizr object can also be used to test for the presence of CSS3 features. The following code shows how to test support for border-radius and CSS transforms:   $(document).ready(function () { if (Modernizr.borderradius) { $('#MyDiv').addClass('borderRadiusStyle'); } if (Modernizr.csstransforms) { $('#MyDiv').addClass('transformsStyle'); } });   Several other CSS3 feature tests can be performed such as support for opacity, rgba, text-shadow, CSS animations, CSS transitions, multiple backgrounds, and more. A complete list of supported HTML5 and CSS3 tests that Modernizr supports can be found at http://www.modernizr.com/docs.   Loading Scripts using Modernizr In cases where a browser doesn’t support a specific feature you can either provide a graceful fallback or load a shim/polyfill script to fill in missing functionality where appropriate (more information about shims/polyfills can be found at https://github.com/Modernizr/Modernizr/wiki/HTML5-Cross-Browser-Polyfills). Modernizr has a built-in script loader that can be used to test for a feature and then load a script if the feature isn’t available. The script loader is built-into Modernizr and is also available as a standalone yepnope script (http://yepnopejs.com). It’s extremely easy to get started using the script loader and it can really simplify the process of loading scripts based on the availability of a particular browser feature. To load scripts dynamically you can use Modernizr’s load() function which accepts properties defining the feature to test (test property), the script to load if the test succeeds (yep property), the script to load if the test fails (nope property), and a script to load regardless of if the test succeeds or fails (both property). An example of using load() with these properties is show next: Modernizr.load({ test: Modernizr.canvas, yep: 'html5CanvasAvailable.js’, nope: 'excanvas.js’, both: 'myCustomScript.js' }); In this example Modernizr is used to not only load scripts but also to test for the presence of the canvas feature. If the target browser supports the HTML5 canvas then the html5CanvasAvailable.js script will be loaded along with the myCustomScript.js script (use of the yep property in this example is a bit contrived – it was added simply to demonstrate how the property can be used in the load() function). Otherwise, a polyfill script named excanvas.js will be loaded to add missing canvas functionality for Internet Explorer versions prior to 9. Once excanvas.js is loaded the myCustomScript.js script will be loaded. Because Modernizr handles loading scripts, you can also use it in creative ways. For example, you can use it to load local scripts when a 3rd party Content Delivery Network (CDN) such as one provided by Google or Microsoft is unavailable for whatever reason. The Modernizr documentation provides the following example that demonstrates the process for providing a local fallback for jQuery when a CDN is down:   Modernizr.load([ { load: '//ajax.googleapis.com/ajax/libs/jquery/1.6.4/jquery.js', complete: function () { if (!window.jQuery) { Modernizr.load('js/libs/jquery-1.6.4.min.js'); } } }, { // This will wait for the fallback to load and // execute if it needs to. load: 'needs-jQuery.js' } ]); This code attempts to load jQuery from the Google CDN first. Once the script is downloaded (or if it fails) the function associated with complete will be called. The function checks to make sure that the jQuery object is available and if it’s not Modernizr is used to load a local jQuery script. After all of that occurs a script named needs-jQuery.js will be loaded. Conclusion If you’re building applications that use some of the latest and greatest features available in HTML5 and CSS3 then Modernizr is an essential tool. By using it you can reduce the amount of custom code required to test for browser features and provide graceful fallbacks or even load shim/polyfill scripts for older browsers to help fill in missing functionality. 

  Read the article

• CodePlex Daily Summary for Thursday, June 27, 2013

  CodePlex Daily Summary for Thursday, June 27, 2013Popular ReleasesV8.NET: V8.NET Beta Release v1.2.23.5: 1. Fixed some minor bugs. 2. Added the ability to reuse existing V8NativeObject types. Simply set the "Handle" property of the objects to a new native object handle (just write to it directly). Example: "myV8NativeObject.Handle = {V8Engine}.GlobalObject.Handle;" 3. Supports .NET 4.0! (forgot to compile against .NET 4.0 instead of 4.5, which is now fixed)Stored Procedure Pager: LYB.NET.SPPager 1.10: check bugs: 1 the total page count of default stored procedure ".LYBPager" always takes error as this: page size: 10 total item count: 100 then total page count should be 10, but last version is 11. 2 update some comments with English forbidding messy code.StyleMVVM: 3.0.3: This is a minor feature and bug fix release Features: SingletonAttribute - Shared(Permanently=true) has been obsoleted in favor of SingletonAttribute StyleMVVMServiceLocator - releasing new nuget package that implements the ServiceLocator pattern Bug Fixes: Fixed problem with ModuleManager when used in not XAML application Fixed problem with nuget packages in MVC & WCF project templatesWinRT by Example Sample Applications: Chapters 1 - 10: Source code for chapters 1 - 9 with tech edits for chapters 1 - 5.Terminals: Version 3.0 - Release: Changes since version 2.0:Choose 100% portable or installed version Removed connection warning when running RDP 8 (Windows 8) client Fixed Active directory search Extended Active directory search by LDAP filters Fixed single instance mode when running on Windows Terminal server Merged usage of Tags and Groups Added columns sorting option in tables No UAC prompts on Windows 7 Completely new file persistence data layer New MS SQL persistence layer (Store data in SQL database)...NuGet: NuGet 2.6: Released June 26, 2013. Release notes: http://docs.nuget.org/docs/release-notes/nuget-2.6Python Tools for Visual Studio: 2.0 Beta: We’re pleased to announce the release of Python Tools for Visual Studio 2.0 Beta. Python Tools for Visual Studio (PTVS) is an open-source plug-in for Visual Studio which supports programming with the Python language. PTVS supports a broad range of features including CPython/IronPython, Edit/Intellisense/Debug/Profile, Cloud, HPC, IPython, and cross platform debugging support. For a quick overview of the general IDE experience, please watch this video: http://www.youtube.com/watch?v=TuewiStN...xFunc: xFunc 2.3: Improved the Simplify method; Rewrote the Differentiate method in the Derivative class; Changed API; Added project for .Net 2.0/3.0/3.5/4.5/Portable;Player Framework by Microsoft: Player Framework for Windows 8 and WP8 (v1.3 beta): Preview: New MPEG DASH adaptive streaming plugin for WAMS. Preview: New Ultraviolet CFF plugin. Preview: New WP7 version with WP8 compatibility. (source code only) Source code is now available via CodePlex Git Misc bug fixes and improvements: WP8 only: Added optional fullscreen and mute buttons to default xaml JS only: protecting currentTime from returning infinity. Some videos would cause currentTime to be infinity which could cause errors in plugins expecting only finite values. (...AssaultCube Reloaded: 2.5.8: SERVER OWNERS: note that the default maprot has changed once again. Linux has Ubuntu 11.10 32-bit precompiled binaries and Ubuntu 10.10 64-bit precompiled binaries, but you can compile your own as it also contains the source. If you are using Mac or other operating systems, please wait while we continue to try to package for those OSes. Or better yet, try to compile it. If it fails, download a virtual machine. The server pack is ready for both Windows and Linux, but you might need to compi...Compare .NET Objects: Version 1.7.2.0: If you like it, please rate it. :) Performance Improvements Fix for deleted row in a data table Added ability to ignore the collection order Fix for Ignoring by AttributesMicrosoft Ajax Minifier: Microsoft Ajax Minifier 4.95: update parser to allow for CSS3 calc( function to nest. add recognition of -pponly (Preprocess-Only) switch in AjaxMinManifestTask build task. Fix crashing bug in EXE when processing a manifest file using the -xml switch and an error message needs to be displayed (like a missing input file). Create separate Clean and Bundle build tasks for working with manifest files (AjaxMinManifestCleanTask and AjaxMinBundleTask). Removed the IsCleanOperation from AjaxMinManifestTask -- use AjaxMinMan...VG-Ripper & PG-Ripper: VG-Ripper 2.9.44: changes NEW: Added Support for "ImgChili.net" links FIXED: Auto UpdaterDocument.Editor: 2013.25: What's new for Document.Editor 2013.25: Improved Spell Check support Improved User Interface Minor Bug Fix's, improvements and speed upsWPF Composites: Version 4.3.0: In this Beta release, I broke my code out into two separate projects. There is a core FasterWPF.dll with the minimal required functionality. This can run with only the Aero.dll and the Rx .dll's. Then, I have a FasterWPFExtras .dll that requires and supports the Extended WPF Toolkit™ Community Edition V 1.9.0 (including Xceed DataGrid) and the Thriple .dll. This is for developers who want more . . . Finally, you may notice the other OPTIONAL .dll's available in the download such as the Dyn...Channel9's Absolute Beginner Series: Windows Phone 8: Entire source code for the Channel 9 series, Windows Phone 8 Development for Absolute Beginners.Indent Guides for Visual Studio: Indent Guides v13: ImportantThis release does not support Visual Studio 2010. The latest stable release for VS 2010 is v12.1. Version History Changed in v13 Added page width guide lines Added guide highlighting options Fixed guides appearing over collapsed blocks Fixed guides not appearing in newly opened files Fixed some potential crashes Fixed lines going through pragma statements Various updates for VS 2012 and VS 2013 Removed VS 2010 support Changed in v12.1: Fixed crash when unable to start...Fluent Ribbon Control Suite: Fluent Ribbon Control Suite 2.1.0 - Prerelease d: Fluent Ribbon Control Suite 2.1.0 - Prerelease d(supports .NET 3.5, 4.0 and 4.5) Includes: Fluent.dll (with .pdb and .xml) Showcase Application Samples (not for .NET 3.5) Foundation (Tabs, Groups, Contextual Tabs, Quick Access Toolbar, Backstage) Resizing (ribbon reducing & enlarging principles) Galleries (Gallery in ContextMenu, InRibbonGallery) MVVM (shows how to use this library with Model-View-ViewModel pattern) KeyTips ScreenTips Toolbars ColorGallery *Walkthrough (do...Magick.NET: Magick.NET 6.8.5.1001: Magick.NET compiled against ImageMagick 6.8.5.10. Breaking changes: - MagickNET.Initialize has been made obsolete because the ImageMagick files in the directory are no longer necessary. - MagickGeometry is no longer IDisposable. - Renamed dll's so they include the platform name. - Image profiles can now only be accessed and modified with ImageProfile classes. - Renamed DrawableBase to Drawable. - Removed Args part of PathArc/PathCurvetoArgs/PathQuadraticCurvetoArgs classes. The...Three-Dimensional Maneuver Gear for Minecraft: TDMG 1.1.0.0 for 1.5.2: CodePlex???(????????) ?????????(???1/4) ??????????? ?????????? ???????????(??????????) ??????????????????????? ↑????、?????????????????????(???????) ???、??????????、?????????????????????、????????1.5?????????? Shift+W(????)??????????????????10°、?10°(?????????)???New ProjectsAriana - .NET Userkit: Ariana Userkit is a library which will allow a file to persist after being executed. It can allow manipulating processes, registry keys, directories etc.Baidu Map: Baidu MapBTC Trader: BTC Trader is a tool for the automated and manual trading on BTC exchanges.Cafe Software Management: This is software for SokulChangix.Sql: Very, very simple ORM framework =)Composite WPF Extensions: Extensions to Composite Client Application Library for WPFCross Site Collection Search Configurator: A solution for SharePoint to allow you to share your site collection based search configuration between site collections in the same web application.CSS Extractor: Attempts to extract inline css styles from a HTML file and put them into a separate CSS fileCSS600Summer2013: This is a project for students enrolled in CSS 600 at University of Washington, Bothell campus.Easy Backup Application: Easy Backup Application - application for easy scheduled backup local or network folders.Easy Backup Windows Service: Easy Backup Windows Service - application for easy scheduled backup local or network folders.fangxue: huijiaGamelight: Gamelight is a 2D game library for Silverlight. It features 2D graphics manipulation to make the creation of games that don't adhere to traditional UI (such as sprite-based games) much easier. It also streamlines sound and input management. General Method: General MethodICE - Interface Communications Engine: ICE is an engine which makes it easy to create .NET plugins for running on servers for the purpose of communication between systems.LogWriterReader using Named pipe: LogWriterReader using Named pipeLu 6.2 Viewer: Tool for analysing LU62 strings. Visualisation of node lists in tree structure, it offers the possability to compare two lu62 strings in seperate windows and visualise the differences between the two segments selected. Fw 2.0 developed by Riccardo di Nuzzo (http://www.dinuzzo.it)Math.Net PowerShell: PowerShell environment for Math.Net Numerics library, defines a few cmdlets that allow to create and manipulate matrices using a straightforward syntax.mycode: my codeNFC#: NFCSharp is a project aimed at building a native C# support for NFC tag manipulation.NJquery: jquery???????????????Page Pro Image Viewer and Twain: Low level image viewer Proyecto Ferreteria "CristoRey": FirstRobótica e Automação: Sistema desenvolvido por Alessandro José Segura de Oliveira - MERodolpho Brock Projects: A MVC 'like' start application for MSVS2010 - Microsoft Visual Studio 2010 UIL - User Interface Layer : <UIB - User Interface Base> - GUI: Graphic User Interface - WEB: ASP.NET MVC BLL - Business Logic Layer : <BLB - Business Logic Base> - Only one core!!! DAL - Data Access Layer : <DAB - Data Access Base> - SQL Server - PostgreSQL ORM - Object-Relational Mapping <Object-Relational Base> - ADO.NET Entity FrameworkSilverlight Layouts: Silverlight Layouts is a project for controls that behave as content placeholders with pre-defined GUI layout for some of common scenarios: - frozen headers, - frozen columns, - cyrcle layouts etc.Simple Logging Façade for C++: Port for Simple Logging Façade for C++, with a Java equivalent known as slf4j. SQL Server Data Compare: * Compare the *data* in two databases record by record. * Generate *html compare results* with interactive interface. * Generate *T-SQL synchronization scripts*UserVisitLogsHelp: UserVisitLogsHelp is Open-source the log access records HttpModule extension Components .The component is developed with C#,it's a custom HttpModule component.V5Soft: webcome v5softvcseVBA - version controlled software engineering in VBA: Simplify distributed application development for Visual Basic for Applications with this Excel AddinVersionizer: Versionizer is a configuration management command-line tool developed using C# .NET for editing AssemblyInfo files of Microsoft .NET projects.WebsiteFilter: WebsiteFilter is an open source asp.net web site to access IP address filtering httpmodule components. Wordion: Wordion is a tool for foreign language learners to memorize words.????????: ????????-?????????，??@???? ????。1、????????????，2、??????????????（????，???????，“?? ??”），3、?????>??>>????5???，4、??"@?/?"?Excel??????@??，5、??“??@"，???????@ 。????QQ:6763745

  Read the article

• I have added a port to the public zone in firewalld but still can't access the port

  - by mikemaccana

  I've been using iptables for a long time, but have never used firewalld until recently. I have enabled port 3000 TCP via firewalld with the following command: # firewall-cmd --zone=public --add-port=3000/tcp --permanent However I can't access the server on port 3000. From an external box: telnet 178.62.16.244 3000 Trying 178.62.16.244... telnet: connect to address 178.62.16.244: Connection refused There are no routing issues: I have a separate rule for a port forward from port 80 to port 8000 which works fine externally. My app is definitely listening on the port too: Proto Recv-Q Send-Q Local Address Foreign Address State User Inode PID/Program name tcp 0 0 0.0.0.0:3000 0.0.0.0:* LISTEN 99 36797 18662/node firewall-cmd doesn't seem to show the port either - see how ports is empty. You can see the forward rule I mentioned earlier. # firewall-cmd --list-all public (default, active) interfaces: eth0 sources: services: dhcpv6-client ssh ports: masquerade: no forward-ports: port=80:proto=tcp:toport=8000:toaddr= icmp-blocks: rich rules: However I can see the rule in the XML config file: # cat /etc/firewalld/zones/public.xml <?xml version="1.0" encoding="utf-8"?> <zone> <short>Public</short> <description>For use in public areas. You do not trust the other computers on networks to not harm your computer. Only selected incoming connections are accepted.</description> <service name="dhcpv6-client"/> <service name="ssh"/> <port protocol="tcp" port="3000"/> <forward-port to-port="8000" protocol="tcp" port="80"/> </zone> What else do I need to do to allow access to my app on port 3000? Also: is adding access via a port the correct thing to do? Or should I make a firewalld 'service' for my app instead?

  Read the article

• Force local IP traffic to an external interface

  - by calandoa

  I have a machine with several interfaces that I can configure as I want, for instance: eth1: 192.168.1.1 eth2: 192.168.2.2 I would like to forward all the traffic sent to one of these local addresses through the other interface. For instance, all requests to an iperf, ftp, http server at 192.168.1.1 should be not just routed internally, but forwarded through eth2 (and the external network will take care of re-routing the packet to eth1). I tried and looked at several commands, like iptables, ip route, etc... but nothing worked. The closest behavior I could get was done with: ip route change to 192.168.1.1/24 dev eth2 which send all 192.168.1.x on eth2, except for 192.168.1.1 which is still routed internally. May be I could then do NAT forwarding of all traffic directed to fake 192.168.1.2 on eth1, rerouted to 192.168.1.1 internally? I am actually struggling with iptables, but it is too tough for me. The goal of this setup is to do interface driver testing without using two PCs. I am using Linux, but if you know how to do that with Windows, I'll buy it!

  Read the article

• Internet doesn't work when enable local Lan

  - by rakesh yadav

  We have the following network setup: A) Router IP 192.168.51.49 B) Windows Server 2008 R2 with dual NIC: B1) WAN interface (192.168.0.2) ( Used for internet) B2) LAN interface (192.168.1.2) ( used for local connectivity) when i keep both LAN Enabled than my internet doesn't work, but if I disabled my local Lan than internet working fine. so please help me how can resolved this issue or should i need to do routing on my server Please find the below attached route print result C:\Users\Administrator>route print =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.51.49 192.168.51.50 276 0.0.0.0 0.0.0.0 192.168.30.227 192.168.30.228 266 192.168.30.224 255.255.255.240 On-link 192.168.30.228 266 192.168.30.228 255.255.255.255 On-link 192.168.30.228 266 192.168.30.239 255.255.255.255 On-link 192.168.30.228 266 192.168.51.48 255.255.255.240 On-link 192.168.51.50 276 192.168.51.50 255.255.255.255 On-link 192.168.51.50 276 192.168.51.63 255.255.255.255 On-link 192.168.51.50 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 202.56.230.5 255.255.255.255 192.168.51.49 192.168.51.50 21 202.56.230.6 255.255.255.255 192.168.51.49 192.168.51.50 21 192.168.26.124 255.255.255.255 192.168.51.49 192.168.51.50 21 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.51.50 276 224.0.0.0 240.0.0.0 On-link 192.168.30.228 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.51.50 276 255.255.255.255 255.255.255.255 On-link 192.168.30.228 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.30.227 Default 0.0.0.0 0.0.0.0 192.168.51.49 Default ===========================================================================

  Read the article

< Previous Page | 176 177 178 179 180 181 182 183 184 185 186 187  | Next Page >