Search Results

Search found 5738 results on 230 pages for 'seo friendly'.

Page 184/230 | < Previous Page | 180 181 182 183 184 185 186 187 188 189 190 191  | Next Page >

• Replacing old SSL cert with a new one with IIS

  - by Wookie321

  I purchased a new cert for my web server (GoDaddy) rather than renewed the current one. In the IIS manager, whenever I do the "Complete certificate request..." and then add my new cert it seems to accept it fine, but when I go off this screen and go back, the cert isn't there? I haven't seen any errors, but I thought it might be because I'm adding a cert with the same friendly name as the old one. I don't want to remove the old cert quite yet, is there a way around this?

  Read the article

• Restart my graphics card without rebooting?

  - by defaye

  Wondered if it is possible to use DevCon to restart a display device as a stop-gap solution to artifacts left over from a graphics card malfunction? In particular it leaves my cursor very un-user-friendly: I found out the hardware ID of my display adapter through device manager (below) [(windows key + pause break) - device manager - display adapters - right click your display adapter - properties - details - hardware ids.] I tried the commands (opened with admin privileges) devcon restart "PCI\VEN_1002" and devcon restart =display but it always come back with No devices restarted.. Is it even possible to restart the graphics card without a system reboot?

  Read the article

• How can I prevent Ask.com Toolbar from being installed every time Java is updated?

  - by abstrask

  As many are painfully aware of, Oracle continues to not only bundle the Java installation with the useless Internet browser toolbar from Ask.com, but also enable its installation by default. In addition to the toolbar, Ask also replaces your favourite search engine in your browser with Ask. Furthermore, the Java installation goes as far as to actually recommend installing this useless junk, meaning that any non IT-savvy person is more than likely to leave it checked and install it (after all, it was enabled by default and the friendly Java installer did recommend it, right?). To add insult to injury, even if you remove the Ask Toolbar, you can be sure to see it again soon, when the next Java update hits you (which seem to happen quite often lately, due to loads of security fixes for Java, but that's another story). I'll duly remove the check-mark to install Ask Toolbar, whenever I update Java, but when supporting my family and friends, it's obvious they don't. How can I prevent the pesky Ask.com Toolbar from being installed in the first place?

  Read the article

• Lightning fast forum based around metadata / tags? [closed]

  - by Dan W

  I wonder if anything like this exists. I'd like to add a forum to my site, but instead of the usual forum/subforum/sub-subforum structure, I'd like to use a metadata/tag approach where everything exists as a single directory, and where there's a search field at the top which instantly (<0.5 sec) filters the threads to a particular keyword or keywords. Also, as the admin, I would be able to add highly visible buttons at the top, which can be clicked on for the main categories I choose for the forum (nevertheless, users can also add tags to their own threads outside of these default main tags I supply if they wish). This approach, if done properly, is more powerful, efficient, maintenance free, scalable and friendly than a standard forum, so I was hoping someone had the same idea and made something out of it. It couldn't be that hard. I'd want the speed to be up to (or near) the standard of this: http://forum.dlang.org/ Other forums (e.g.: phpBB, shudder) are orders of magnitude worse than that in terms of latency (posting or browsing), and I think that is wrong, even in principle ;)

  Read the article

• Apache Rewrite Rules breaking each other?

  - by neezer

  I have this rule: RewriteCond %{REQUEST_URI} ^/(manhattan|queens|westchester|new-jersey|bronx|brooklyn)-apartments/.*$ RewriteCond %{REQUEST_URI} !^/guide/(.*)$ RewriteRule ^(.*)$ /home/neezer/public-html/domain.com/guide/$1 [L] Which works great on it's own. Essentially, I have a bunch of directories that have a bunch of files in them that I want to keep in the "/guide" folder, but I want them to appear at the web root for SEO reasons. This rule works, but unfortunately the original URL's still work too (with "/guide"). I want to 301 Redirect the ones with "/guide" in the URL to those without, without actually moving the files on the server. I tried adding this rule: RewriteCond %{REQUEST_URI} ^/guide/(manhattan|queens|westchester|new-jersey|bronx|brooklyn)-apartments/.*$ RewriteRule ^guide/(.*)$ http://www.domain.com/$1 [R=301,L] ... but that breaks my first rule completely. Any thoughts about what I might be doing wrong? Please let me know if you need to know anything else from me to help me with this issue.

  Read the article

• Configuring Ubuntu 10.04's Greeter Screen

  - by Skizz

  I have an Ubuntu server (9.04 at the moment) and an Ubuntu desktop which I recently upgraded to 10.04. Once I'd set up the users and groups on the desktop to match the server (I'm new to this, I think LDAP would do this for me, but that's another question), the friendly greeter screen no longer displays the same set of users1. In 9.04 (the previous version running on the desktop PC) there were four users shown. These had UIDs of 500 to 510. Changing the UIDs is one solution, but that would mean changing the UIDs on all my linux PCs, and that is a might PITA (unless there's a tool to make it less painful). How can I get the greeter in 10.04 to show users with UIDs in the 500s without resorting to changing the UIDs? I use the greeter screen with user pictures as the PC is mainly for use by my young children and clicking the picture is a bit easier (they still need to type a password though).

  Read the article

• Ubuntu terminal questions

  - by Camran

  I am wondering about my VPS providers ubuntu terminal. Are all these terminals the same? I think they are so user-UN-friendly. I can't copy-paste into the terminal, when I try opening textfiles, I can't scroll up and down easily. I cant save easily. Nothing is easy... Is it always like this with Ubuntu? Is there any way to make it easier? I use windows but I login to my vps provider with login details and then simply click "terminal" to open the terminal. Please help me out here

  Read the article

• A complete tool for auditing and archiving emails would be helpful for the community?

  - by Renato Todorov

  Please, don't treat this like a discussion question, I'm looking for direct answers: Yes / No, because... I work on a financial company and I'm needing a tool for email archiving and auditing. The compliance sector is asking for it and I have to provide it. I've searched and found two solutions: MailStore (commercial, Windows only) and Enkive (open source, very poor UI and lack of features). I'm using Postfix as MTA and Courier for IMAP/POP access. I'm almost deciding to write it myself, I have the knowledge needed, but I'm wondering right now if it's worth to put (a lot) more hours to make it open source and user friendly. So my question is, have you ever had the same need? Would this be a helpful solution? Is there any other good tool that I haven't found? Thank you!

  Read the article

• How to restrict access to a specific wireless network to only 1 user profile in Windows 7.

  - by Mathlight

  Hi all, I'm using Win7 SP1. I've got multiple users on the laptop that can / must connect to a wireless network, lets call it Wireless1. I've got an second wireless network, (lets call it Wireless2), which I want to limit access to only the admin user of the laptop. Now I can remove Wireless2 in the network manager every time, but i want a more user friendly solution, so that only the admin can connect to Wireless2, and all the other users cannot ( they may see the network, but must enter the password, like all other networks ). Any ideas?

  Read the article

• Starting services in batch file on windows 7

  - by Dima

  I have a fairly simple batch file which does just one thing - "net start myservice". This batch file gets shortcut-ed in a program group by installer so that users can simply click on the icon and get things started (or stopped). All works well in XP for the users with admin rights. But things get hairy on Win7 as the batch need to be run "as administrator" explicitly and often users don't know this. So my question is how to make this friendly? Telling users to right click and run as admin on Win7 and simply click on XP is kind of weird twist. I need a smart automatic simple thingy. I could probably use "runas/user:administrator" in the batch itself, but this "administrator" account might not be available on some machines. I'm looking for a universal solution for installing things like this on any Windows box. Ideas? How would you do this?

  Read the article

• Sun T1000 Fan Noise - Big Issue

  - by Ed Austin

  Long and short, the T1000 makes more noise than 7 HP Servers combined. Firmware updated to latest version. PICL running under Solaris OK. Diagnostics all OK. It is driving us mad. We have a server room in our small office and we can hear this baby through thick concrete.... I cannot believe Sun doesn't mention how loud they are.... thought this was an environmentally friendly server.. Help really appreciated before it drives us all mad.

  Read the article

• Need help with an .htaccess URL rewriter

  - by AlexV

  I'm trying to do another SEO system with PHP/.htaccess... I need the following rules to apply: Must catch all URLs that do not end with an extension (www.foo.com -- catch | www.foo.com/catch-me -- catch | www.foo.com/dont-catch.me -- don't catch). Must catch all URLs that end with .php* (.php, .php4...) (thwaw are the exceptions to rule #1). All rules must only apply in some directories and not in their subdirectories (/ and /framework so far). The htaccess must send the typed URL in a GET value so I can work with it in PHP. Any mod-rewrite wizard can help me?

  Read the article

• FTP server (vsftpd) with webgui

  - by manutenfruits

  I want to build a file server to make users able to upload and download mostly multimedia, but also common files. Right now I have an Arch installation with vsftpd and I'm about to install miniDLNA for multimedia sharing. The only problem is that FTP doesn't seem to fit my needs, because almost always makes the users need a client such as FileZilla to make the server friendly. I have been looking for a web frontend for vsftp but apart from management interfaces there's nothing. I need a frontend accessible from a browser through which users can navigate throught the folders in an easier and more elegant way than the plain FTP display that browsers make by default. It should be able to let users upload files and, as an awesome extra, let them play the multimedia directly on the browser. For this, I am willing to dump FTP if needed, I've heard about HTTP File Servers but don't know too much about it. I could code everything myself, but there's gotta be something out there already.

  Read the article

• Switch 302 redirect to 301 with Apache 2 ProxyPass in front of Tomcat 6

  - by Gearóid

  I'm trying to optimise my site for SEO and it seems as though their is a 302 direct in action for the http requests. I'm hosting my app on a Tomcat 6 server which lies behind an Apache 2 server. I use the ProxyPass method (http://tomcat.apache.org/tomcat-6.0-doc/proxy-howto.html) to forward all requests to port 8080 (the port my app is hosted on). I've seen a lot of advice on how to set the redirect type when using the VirtualHost method but none to do with ProxyPass. The app is a Struts app that forwards users on to index.jsp when they hit the base url. Could this also be the issue? I'm grateful for any help on this one! Cheers!

  Read the article

• 500 Internal Server Error after moving Joomla installation to new environment

  - by rad

  (This is the first time I moved the website so please don't be hard on me.) After moving the website, the homepage shows up properly but other pages do not. I get 500 Internal Server Error on all other pages. Before moving, the Search Engine Friendly URLs and Use URL rewriting were enabled in the Joomla Dashboard. Is this the reason the other pages are not showing up? If so, how do I fix this? I think the homepage shows up because the url myWebsite.com redirects to myWebsite.com/index.php automatically. Note that I have transferred all of the Joomla the files through Filezilla and imported the MySQL database properly and also edited the configuration.php as set the proper settings for the database.

  Read the article

• Apache .htaccess problem: No input file specified.

  - by Michal M

  Hello Everyone, Can someone help me with this. I'm feeling like I've been hitting my head against a wall for over 2 hrs now. I've got Apache 2.2.8 + PHP 5.2.6 installed on my machine and the .htacces with code below works fine, no errors. RewriteEngine on RewriteCond $1 !^(index\.php|css|gfx|js|swf|robots\.txt|favicon\.ico) RewriteRule ^(.*)$ /index.php/$1 [L] The same code on my hosting provider server gives me a 404 error code and outputs only: No input file specified. index.php IS there. I know they have Apache installed (cannot find version info anywhere) and they're running PHP v5.2.8. I'm on windows xp 64-bit, they're running some Linux and php in cgi/fastcgi mode. Can anyone suggest what could be the problem? PS. if that's important that's for CodeIgniter to work with friendly URLs.

  Read the article

• Multiple Graphics Cards on Fedora 15 (Gnome 3)

  - by Michael

  I have the (delightful) misfortune of having 3 graphics cards. They are XFX Radeon 5750s. Each drives 2 monitors via dvi. I am having a really hard time getting these running on fedora 15 (gnome 3). So my setup is 3 columns of 2 monitors (the upper monitor is mounted upside down in each column to reduce the bezel between monitors). When the (graphical) login screen comes up all 6 have the blue stripey background that must be the default, but then when I login, things get interesting. In the xorg.conf below, you will see only 2 of the screens in the serverlayout while the other 4 are commented out. Logging in with only 2 of the screens active works well (and it even remembers that the top one is upside down, and should be considered above the lower, i am not sure where it stores this info, but i set it using the graphical "Displays" settings) However, as soon as I uncomment a third screen, or more, it gives me an error message when I login. It's one of those friendly, less helpful messages (Oh no! Something has gone wrong. A problem has occurred and the system can't recover. Please log out and try again). If i do not use an xorg.conf, then the "Displays" prefs pane shows only the two monitors on one of my graphics cards Thanks to anyone who can help me get going! (xorg.conf and then lspci below, and xorg log) xorg.conf Section "ServerLayout" Identifier "X.org Configured" Screen "Screen0" 0 0 Screen "Screen1" Below "Screen0" # Screen "Screen2" RightOf "Screen0" # Screen "Screen3" RightOf "Screen1" # Screen "Screen4" RightOf "Screen3" # Screen "Screen5" RightOf "Screen4" InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Files" ModulePath "/usr/lib/xorg/modules" FontPath "catalogue:/etc/X11/fontpath.d" FontPath "built-ins" EndSection Section "Module" Load "record" Load "dri" Load "dbe" Load "extmod" Load "dri2" Load "glx" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor2" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor3" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor4" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Monitor" Identifier "Monitor5" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Device" Identifier "Card0" Driver "radeon" BusID "PCI:4:0:0" EndSection Section "Device" Identifier "Card1" Driver "radeon" BusID "PCI:5:0:0" EndSection Section "Device" Identifier "Card2" Driver "radeon" BusID "PCI:6:0:0" EndSection Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Card0" Monitor "Monitor1" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Card1" Monitor "Monitor2" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen3" Device "Card1" Monitor "Monitor3" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen4" Device "Card2" Monitor "Monitor4" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen5" Device "Card2" Monitor "Monitor5" SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection lspci output follows [tgm@tgm ~]$ lspci 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers (rev 13) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.2 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 3 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller #1 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller #2 02:00.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 03:00.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 03:02.0 PCI bridge: nVidia Corporation NF200 PCIe 2.0 switch for mainboards (rev a3) 04:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 04:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 05:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 05:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 06:00.0 VGA compatible controller: ATI Technologies Inc Juniper [Radeon HD 5750 Series] 06:00.1 Audio device: ATI Technologies Inc Juniper HDMI Audio [Radeon HD 5700 Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) xorg log (posted to fpaste due to how long it is. thanks to marcusw for the request) http://www.fpaste.org/r5ww/ xorg log with all 6 monitors enabled in xorg.conf (they all turn on and have blue, but then one gets the aforementioned user-friendly error message). http://www.fpaste.org/X63H/

  Read the article

• Remove a known network from Windows 8

  - by Edward Brey

  When Windows 8 detects a network based on the assigned IP address, netmask, default gateway, etc., it remembers the network along with the setting you give it as a public or private network. If you change the configuration of a network (e.g. reconfigure your router), Windows may determine you are on a new network and assign it a name of Network 2 or YourAPN 2. This less-than-friendly name shows up in many places in the Windows 8 UI, but unlike the good old days of Windows 7, there doesn't appear to be any UI to merge or delete these networks. What's the best way to merge or delete networks you don't want?

  Read the article

• Posting videos to a website... with a dynamically updating interface

  - by Johnny W

  I'm currently putting together a website for my Luddite friend. He needs a blog, photos and videos... all easily updateable by him. WordPress and Blogger both have brilliant functionality to allow you to host your own blog on your own domain, but what about photos and videos? Does YouTube or Google videos or Vimeo or MSN Video or anyone offer the ability to easily insert a video navigation interface onto your own site? (Something similar to YouTube's "Channel" pages, except on your own domain?) Same goes for photos. I'm pretty sure FlickR doesn't allow you to easily upload and manage photos for viewing on your own domain. Does anyone else? My friend doesn't want to be editing any HTML and I don't want to be creating a complicated system to handle tons of different videos. There must a user-friendly solution in this day and age? Thanks for any help!

  Read the article

• PGP - MailCloak/Gpg4Win/etc

  - by ericl42

  Hello, I have used Gpg4Win in the past along with FireGPG to have encryption on my emails. I am needing to roll this out to quite a few more people and was wondering if anyone else had some products they preferred better. The criteria I need is free and as user friendly as possible. I looked at MailCloak but I have had some issues with it on 1 of the 2 computers I've been testing on. It seems like it might work pretty well as a overall solution but on my computer I keep getting "Identity cannot be created." and not sure whats going on with that. Thanks for the info.

  Read the article

• VMWare Workstation Dev Machine Disks: one fast or four echofriendly raid?

  - by Avi

  I'm building a new dev computer. It will be running a few VMWare Worksation virtual machines - A dev machine running VS-2010, a build machine, a version-control machine, a web server for testing, a "personal" machine running office etc. I'll be connecting the computer to my stereo, so I'll also be running iTunes (possible on a dedicated VM) and I want the computer to be a silent one. I'll probably use an Antec P183 case. I was advised on Serverfault to use Raid10 for performance. Raid 10 uses 4 disks. So, my question is as follows: In terms of heat, noise, reliability, warranty, price, capacity and performance, what would you suggest: A Raid10 4 disk array using eco-friendly disks such as the $94 1TB Western Digital Caviar Green, or one high performance disk such as the 2TB Western Digital Caviar Black at $280?

  Read the article

• Comparison of Unix shells

  - by Andy White

  Of the major Unix shells (bash, ksh, tcsh, zsh, others?), are there any compelling reasons to use one over another? Which is the most interactive/command-line friendly? Which is the most conducive/intuitive for writing scripts? Are there any major built-in features that one shell offers that others don't? Are any of these shells really good for one type of function, but not another? Or are they all pretty well-rounded/flexible? Is it just a matter of personal preference? I can make this community wiki if anyone prefers.

  Read the article

• Lightweight window manager for Linux for Virtual Desktop / Multimon

  - by mattcodes

  Previous used Ubuntu Gnome with Compiz but for my basic spec intel macbook (4 years old) its a little too heavyweight. So for now Im back on my macbook with os x, but now considering going back to Linux. Im looking for a window manager that has the following properties: Supports virtual desktop (need 4 minimum) Works well with multi monitors - can move an app with shortcut from one monitor to the other (on same virtual desktop) Can remember window position (i.e. open vim on 2 monitor) - however must coerce everything back to first screen when 2nd screen is unplugged Keyboard shortcut friendly Not too hard to install Works well with minimum hardware such as integrated graphics Please suggest and share your experiences

  Read the article

• Exchange 2003 SMTP SSL and various email clients

  - by FrancisV

  This Exchange 2003 server sits behind a firewall with a virtual SMTP server listening on port 465 and attached an SSL certificate from Comodo to the virtual server. However, when trying to send from Apple Mail.app 4.x and Outlook 2011 for Mac, it never completes the connection (time out). Oddly though, the same setup works with Thunderbird. My question is: Does it matter if the friendly name of the certificate is different from the internal hostname? The machine has 2 hostnames: external and internal. The official SSL is using the external name. When using a self-signed certificate with the same name as the internal, I still can't send from the Mail.app and Exchange clients but I can with Thunderbird.

  Read the article

• Best window manager for Linux for Virtual Desktop / Multimon

  - by mattcodes

  Previous used Ubuntu Gnome with Compiz but for my basic spec intel macbook (4 years old) its a little too heavyweight. So for now Im back on my macbook with os x, but now considering going back to Linux. Im looking for a window manager that has the following properties: 1) Supports virtual desktop (need 4 minimum) 2) Works well with multi monitors - can move an app with shortcut from one monitor to the other (on same virtual desktop) 3) Can remember window position (i.e. open vim on 2 monitor) - however must coerce everything back to first window when 2nd screen is unplugged 4) Keyboard shortcut friendly 5) Not too hard to install 6) Works well with minimum hardware such as integrated graphics Please suggest and share your experiences

  Read the article

< Previous Page | 180 181 182 183 184 185 186 187 188 189 190 191  | Next Page >