Search Results

Search found 6104 results on 245 pages for 'fast esp'.

Page 186/245 | < Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >

• External SATA drive does not work without the optional USB cable *also* connected

  - by Software Monkey

  I have Vantec NST-260SU external eSATA/USB drive enclosure (which came with an optional separate power supply) connected to a relatively new Windows 7 computer. The drive should work as a SATA drive with either the separate power supply or using a USB cable solely for power. I would prefer to use the external power supply because I have used all my rear USB ports. Now, if I connect both the eSATA and USB cable, then: The drive shows in the BIOS list of AHCI drives (and not in the list of attached USB devices). Everything I can see about it in Computer Management seems to show it as a SATA driver (for example, it shows as "Location 0 (Channel 5, Target 0, Lun 0)" like my other SATA drives (and not "on USB Mass Storage Device" like my USB flash-drives). It seems very fast, very much faster than my USB flash drives. However, if I disconnect the USB cable and attach the power adapter instead, the drive does not show in the BIOS list and cannot be seen by Windows. The power LED on the enclosure is lit, and the drive enclosure becomes warm after running for a bit, so I am sure it is receiving power. Does anyone know if this device requires both the USB and eSATA cable, and if so, why? Or is there possibly something I need to do to reset the enclosure to not need the USB - the install instructions are pretty clear that you must connect the SATA cable before connecting the USB cable in order for the drive to function as SATA, which I am sure I did. PS: I have reviewed the small manual which came with it, which has not been of help.

  Read the article

• Very slow context menu in Windows 8

  - by burzum

  I've installed Windows 8 Pro on a blank new SSD, the system is on c:\. I do not think this problem was existent when I started using Windows 8 but I think it started to happen after I've symlinked (mklink /D) a folder from another drive, a SATA drive, to c:\xampp\htdocs. When I right click a file or folder inside the symlinked folder it always takes at least ~5-10 seconds until the context menu comes up. This also happens sometimes, but not all the time for files and folder outside of the symlinked folder. Also when I delete folders the delete folder dialog seems to get locked and does not continue. When I delete a folder using rmdir from the command line it works fine and pretty fast. It appears to me like the file explorer in Windows 8 is pretty bad compared to any other Windows I've used before? Any idea how to get these problems solved? I've already removed a lot of context menu entries; the only ones left are the tortoise git context menus but I'm sure that's not the problem.

  Read the article

• Win7 'locking' process/files/folders?

  - by Dynde

  I've had a fair bit problems with sometimes files/folders/processes being 'locked' by Windows. The weird thing is, it's not like the traditional sense, I think, where tools like UnlockIT and wholockme would work. It seems that just giving it a little often helps - making me think it could either be the HDD, the memory, or something in Windows. A scenario: I go into a folder - don't open anything at all, go back up, cut or drag-move the folder to someplace else, it says "Action can't be completed because the folder or a file in it is open in another program". Waiting sometimes 20 seconds sometimes a little longer, and I can move it. Another scenario is deleting a bunch of files in a folder, and it appears that everything is gone, but then suddenly after a few seconds an .exe file pops back up, and I can't delete it. Waiting a few minutes, then pressing refresh and it's gone. I have the strangest feeling that there's a problem with either HDD or memory. I already tried disabling Windows indexing service with no luck. Does anyone have any ideas? EDIT: I should say, that I have a very fast system, 16 GB DDR3 RAM, i7-2600k CPU, SSD main HDD, so I really should not be experiencing any sort of problems, where one might say that it's "reasonable" for the system not to respond right away. Edit2: And I updated SSD firmware a couple months ago, so it shouldn't be bad release FW either

  Read the article

• Distributed storage and computing

  - by Tim van Elteren

  Dear Serverfault community, After researching a number of distributed file systems for deployment in a production environment with the main purpose of performing both batch and real-time distributed computing I've identified the following list as potential candidates, mainly on maturity, license and support: Ceph Lustre GlusterFS HDFS FhGFS MooseFS XtreemFS The key properties that our system should exhibit: an open source, liberally licensed, yet production ready, e.g. a mature, reliable, community and commercially supported solution; ability to run on commodity hardware, preferably be designed for it; provide high availability of the data with the most focus on reads; high scalability, so operation over multiple data centres, possibly on a global scale; removal of single points of failure with the use of replication and distribution of (meta-)data, e.g. provide fault-tolerance. The sensitivity points that were identified, and resulted in the following questions, are: transparency to the processing layer / application with respect to data locality, e.g. know where data is physically located on a server level, mainly for resource allocation and fast processing, high performance, how can this be accomplished? Do you from experience know what solutions provide this transparency and to what extent? posix compliance, or conformance, is mentioned on the wiki pages of most of the above listed solutions. The question here mainly is, how relevant is support for the posix standard? Hadoop for example isn't posix compliant by design, what are the pro's and con's? what about the difference between synchronous and asynchronous opeartion of a distributed file system. Though a synchronous distributed file system has the preference because of reliability it also imposes certain limitations with respect to scalability. What would be, from your expertise, the way to go on this? I'm looking forward to your replies. Thanks in advance! :) With kind regards, Tim van Elteren

  Read the article

• Firefox takes a really long time to load some sites on Ubuntu

  - by Dave

  Hello guys, I have an issue here. Some sites - just a few - takes a really long time to load on Firefox. One example is A List Apart (http://www.alistapart.com/) which takes more than 30 minutes (yes, minutes, not seconds). On Opera, ou even through a telnet session, the problematic sites run without problem, fast as expected. I am using Linux 8.04, running Firefox 3.6.3 downloaded from mozilla site, with a 10M ADSL connection. I tried many tweaks I found googling, like disable IPv6, and change http pipelining settings on FF's about:config. None worked. I also used Firebug to find what phase during negotiation is the bottleneck. Findings are in the screenshot. Well guys, any idea what is the issue? And how to solve it? I repeat, this only happens with firefox (3.6.3 and prior versions), for a few sites only (even sites with much more requests, images, javascripts, stylesheets work fine), and http pipelines and IPv6 tweaks on about:config didn't work. Thanks

  Read the article

• Apache suddenly very slow on http and faster on https

  - by hsnm

  Background: I have Apache 2 running on ubuntu. There is a low usage on it and mostly being accessed for a web service URL from mobile apps. It was working fine until I installed SSL certificates. I now have both http and https. When I access the server using https, I get a fairly quick response (but probably not as fast as before). When I use http, it's so slow. What I tried: From this post: I curl localhost from the host and it takes some time, meaning there is no routing issue. The server runs on Amazon EC2 instance and is managed by me only. Also: I see that Apache once running, creates the maximum number of processes it is allowed to, which was not the case before. I lowered the MaxClients to 20 and I think I'm getting faster responses but it still takes over a minute and I always have MaxClients Apache processes. dmesg returns many [ 1953.655703] TCP: Possible SYN flooding on port 80. Sending cookies. When I netstat I get many entries with SYN_RECV. Possibly a DDoS attack? From EC2's monitoring diagrams I see a pattern of high "Maximum Network In (Bytes)" since 2 days ago. By the way the server is still being tested, the actual traffic is very low and not consistent. I tried to go with this solution to limit incoming connections using iptables, still no luck, but I'm trying. Question: What could be the problem? Is this a DDoS attack?

  Read the article

• port forwarding/network settings preventing from game hosting

  - by Xitcod13

  I asked where to post this question on stackoverflow meta and they directed me here. Im on wireless connection and I want to host games in StarCraft: Brood War and i've been looking everywhere on how to accomplish that. My internet is amazingly fast so its not an internet problem (and when i play other peoples games dont experience lag) I found out that i need to have a static IP but I have already checked that i do (i downloaded a program to make my id static and it already was; The program asked for which router I used So i think it checked the router settings already) I found out that i need to allow Sc access through the firewall which i already did (i have zone-alarm but I allowed it everything possible except receiving emails lol) I have recently noticed that few people actually can join my games but most of them cannot. I dont know whats going on here. I really want to be able to host games overall how do I go about checking what is wrong with the network. Update: Alright I figured out what i did wrong in the first part I did not actually set up forwarding on the router -.- I have tried to fix my mistake. I went to forwarding options in my router (as this guide for my specific router suggests) but when i click ok I get a message incorrect ip address. 192.168.1.1 is my routers address. The default address that appears there is 192.168.1 (blank) I have set it to my computers current Ip4 adress which 192.168.1.23 I hope this works If so i will post it as an answer and mark it.

  Read the article

• Does using a hexacore CPU make sense?

  - by Exa

  I'm currently planning to upgrade my computer system and I want to exchange CPU, board and RAM. I already had a look at some hexacore-CPUs from AMD and would like to know if it makes any sense to use such a CPU with six cores. Is there any software which really uses six cores? Especially in gaming? I'm using this PC mostly for gaming and from time to time for developing. I know that on the dual-core system (2 x 3GHz) I currently use, Visual Studio creates two instances of the compiler, one for each core. Would there be six instances of the compiler on a hexacore system for super fast compiling? Is there any software that uses six cores? Would running two applications cause the usage of more CPUs? (For example two CPUs for a game you're playing while two other CPUs are used for compiling at the same time) I hope someone can point out the benefits of a hexacore system. The OS would be Windows 7 64 Bit and I use the PC for gaming most of the time. (Crysis 2, CoD, stuff like that)

  Read the article

• less maximum buffer size?

  - by Tyzoid

  I was messing around with my system and found a novel way to use up memory, but it seems that the less command only holds a limited amount of data before stopping/killing the command. To test, run (careful! uses lots of system memory very fast!) $ cat /dev/zero | less From my testing, it looks like the command is killed after less reaches 2.5 gigabytes of memory, but I can't find anything in the man page that suggests that it would limit it in such a way. In addition, I couldn't find any documentation via the google on the subject. Any light to this quite surprising discovery would be great! System Information: Quad core intel i7, 8gb ram. $ uname -a Linux Tyler-Work 3.13.0-32-generic #57-Ubuntu SMP Tue Jul 15 03:51:08 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux $ less --version less 458 (GNU regular expressions) Copyright (C) 1984-2012 Mark Nudelman less comes with NO WARRANTY, to the extent permitted by law. For information about the terms of redistribution, see the file named README in the less distribution. Homepage: http://www.greenwoodsoftware.com/less $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 14.04 LTS Release: 14.04 Codename: trusty

  Read the article

• Would an array of SSD drives be able to succesfully substitute the system memory?

  - by Florin Mircea

  I watched a few videos trying to answer this. This video (youtube.com/watch?v=eULFf6F5Ri8) shows a bunch of guys stacking 24 SSD's reaching a peak of around 2GBps r/w. That's under the limit of the worst DDR3 in this list (memorybenchmark.net/write_ddr3_amd.html) - that shows DDR3 memory performance varying from 2.78 to 6.55 Gb per second, but that video is over 3 years old. This video (youtube.com/watch?v=27GmBzQWwP0) shows a more optimistic situation, but for PCI-E SSD drives: 5 drives peaking at around 4Gb. And this other video shows that stacking up more than 3 SSD's doesn't realistically offer a substantial added performance. This and the fact that in all benchmarks the drives act quite poorly when dealing with small files (5k file read/write averaging from 10MB to around 30-40MBps) as opposed to how native memory handles such files, seems to indicate a definite NO to this question. Also, the write life cycle is indeed limited and the drives might wear out quickly, as kindly pointed out by paddy. However, I wanted to get more opinions on this. Would it be possible to at least obtain current memory performance with SSD's in RAID 0? And if so, in what circumstances? I am assuming using this configuration with a Windows OS that has a memory pagefile resident to that stack of SSD's, thus making it very fast to work with.

  Read the article

• How is the extra mSATA SSD disk used/configured in a Dell XPS laptop?

  - by Mark

  Some machines in the new XPS laptop range from Dell come with a regular, large (500GB+) HDD and an additional 32GB m-SATA SSD. The only detail I can find about this extra drive on the Dell site is this: Store your important files, multimedia and photos with XPS 15’s large hard drive options. To get instant access to your media, choose an optional mSATA solid-state drive (SSD) that can boot up to twice as fast as a regular hard drive and resumes in less than 1 second. I'd like to know more about how this extra drive is set up and used, specifically: Is anything installed on it (e.g. OS files or a boot loader) or is it just used as swap space? Is the m-SATA drive visible as a lettered drive in Windows? (I'd guess not if it's used for swap file only.) Is this unusual configuration likely to cause any problems later down the line - e.g. when upgrading to Windows 8? As usual, Dell's sales team haven't been able to help. If anyone's actually got a Dell machine with this or a similar hard drive set-up and can give a definitive answer rather than speculation I'll accept the answer.

  Read the article

• How can I duplicate HBCD's XP boot loader with my MBR?

  - by Warpstone

  I'm stumped. I'm migrating a Win XP Lenovo T500 to an SSD: I copied the XP partition using EaseUS to the SSD. Aligned the boot sector using Gparted The MBR needs to be rebuilt (fair enough) However, all attempts to use the Windows Recovery console hang (both via a boot CD and even when the console was installed as a boot option). I've tried using a bunch of tools to rebuild/replace the MBR, but no dice. They all say the MBR has been fixed, but I cannot load Windows from the SSD. The HBCD's boot from windows option works just fine however. I'm confused as to what HBCD can do that my drive can't. How can I get that functionality on my SSD? Is it a MBR fix I can mirror? The SSD is extremely fast when I do use HBCD to boot up... but it would be nice to not need a token-based access to the machine! :) Note: I know, windows 7 may be worth a fresh install, but I'm trying to avoid the cost and hassle if possible.

  Read the article

• Utility to grant admin rights to a user in Windows XP for few hours/days?

  - by user15660

  I have two accounts on my windows xp home desktop. The default regular user is used for everything and the 2nd user which has admin rights is used only for installations. I do this to avoid malware infestations during web browsing and limited user account is guarding against online threats to a good extend but many programs refuse to run under limited rights like revo uninstaller. many installs i run from limited user by selectin "run as" from right click context menu of the .exe file. but some apps need admin rights for certain. I use "switch user" to go to admin mode and do the install/uninstall. but the admin user has none of my preferences bookmarks setup nor has my locate32 indexing done and ready for fast search Is there a utility which I can use "run as" login in administration login and use that to grant my limited user admin rights for a limited amount of period like few hours or days? Please help. I guess MS might have closed many doors of it for fear of exploitation of the API. are there any?

  Read the article

• Ubuntu 10.04 network manager issues

  - by Shark

  I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

  Read the article

• when to upgrade server to include more cores, versus more processors, versus additional server?

  - by gkdsp

  The server hosting market is separated into single, double, qual, etc., processors, where each processor has several cores, or CPUs. My company will offer a Linux-based web application that relies on an Apache web server and a middle tier for business logic. The middle tier is used to crunch math, and return result to a client. Many clients may access the application simultaneously. The company will start with one processor having 4 cores. I'm trying to understand how the app uses the cores and then how to scale the application as business grows, in terms of servers/processors/cores. For example, I'd assume initially one core would be used for Apache, and the other 3 used to process client's requests for math crunching... Question 1: does that mean, with the 3 cores available, I can handle 3 separate client requests simultaneously (e.g. 1 for each of 3 cores)? I mean, except for the shared RAM, is this effectively like having 3 individual machines (from pt of view or processing client requests simulaneously)? Or, only one client's request may be processed at any one time, but that client's request is divided up into up to 3 cores depending on the type of process running that does the math crunching and whether or not it can take advantage of multi threading (so the # of cores impacts how fast any one client request completes)? I'm confused about what the cores mean to the application here. Question 2: As the business grows and more client requests need to be processed, should the server be upgraded to (A) a new machine with more cores, (B) a new machine with two processors, 4 cores each, or (C) keep the original server and add another server with a single processor? Which route provides the most efficient way to scale the application, in terms of processing more client requests per time interval? Is the choice, for example, limited by RAM (when you need more RAM than box can handle it's time to add another server), or something else? Question 3: Is the total number of client requests processed simultaneously equal to the number of cores times the number of servers (minus the one core for Apache)?

  Read the article

• Computer keeps restarting [closed]

  - by Joris

  I have a strange problem with my desktop pc, when I start it, it just restarts immediately, it displays the bios/motherboard logo and then restarts. I can't access the bios to edit settings because it restarts to fast. Then I tried different things to fix it with mixed success. (I also tried to reset the bios without success) I noticed that a capacity from the graphics card was broken (it looked exploded) so I ordered a new graphics card & plugged it in the computer. It didn't change much, still the same problem. Then I unplugged everything that's not necessary and put only 1Gig RAM in the motherboard (usually it has 4 x 1Gig RAM) and the computer started, then I putted another gig of RAM and the computer still started. (starting=booting windows) When I putted in the 3th RAM it didn't boot anymore (again restarting all the time) so I removed this 3th gig of RAM and this is where it gets weird. I expected the computer to boot again because it is exactly the same configuration as before - which worked - but the computer didn't want to start. It just gave the same problem as before (restarting all the time.. ) Anyone an idea what might be wrong?

  Read the article

• How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

  - by Todd V. Rovito

  I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

  Read the article

• Need Help Scoping a Server to use for study (MCITP Ent Admin + SharePoint 2010)

  - by AVFamily76

  i need to study for mcitp, but i also need to study for sharepoint 2010 i have a poweredge 1850 with two single-core CPUs + two 73G drives - it kills me on electricity, so don't want to use it, and it won't do VT, but it could be one of three boxes for a lab that's cheap, but will cost a lot on electricity i was thinking . . . OPTION #1 Opteron 4170 HE (50 watt chip), 6-core, only two-bills ($200), but the board's are $250, so that's an $800 box, then get another box to dual-boot Win7/Hyper-V on the cheap...? OPTION #2 Used Quad - but how many VM's that are really banging away could it run at same time? (Server 2008r2, SQL 2008r2, Search Server) OPTION #3 Study from books and just get one box that can run two VM's at same time, even if slowly. the last time i had and used a home lab was five years ago when i had a DC, SQL, Exchange and business app box, that's where i got my server skills was just banging on it for four years, but didn't read any books, so now i have to get certified and know the material, and just am not sure how much attention i should pay to the box i use versus the studying time and reading. sorry it's a subjective question, and am obviously open to all sorts of abuse here, but hope you can tell me also how many VM's i can run at the same time given what they'll be doing (SQL and SharePoint FAST search server are resource hungry) thanks!

  Read the article

• Dual hard drive Windows 7 system, modified the registry to get programs to install on second drive, now IE doesn't work

  - by paul

  I have a dual hard drive Windows 7 system, Windows is installed on an SSD (C:) and I modified the registry to try to force programs to install on second HDD drive (another letter). The registry edits are pretty simple, just a few keys in HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion to change the drive letter. For the most part the system is very fast and works great, but IE doesn't work anymore. With IE10, it opens for a flash with a white window then closes. I tried installed IE11 which opens a white window for a few seconds, doesn't respond, then crashes. I've tried all the solutions I could find. This includes resetting the IE settings, "uninstalling" and re-installing IE, which is just turning it on and off in "Turn Windows Features on or off", copying the Program Files\Internet Explorer files onto both/either drives, changing the registry keys back to use C:, lots of rebooting, and safe mode. Nothing has worked. I don't see errors in the event viewer, but I might not know what to look for. Any ideas on how to get IE running? I don't need IE for daily browsing, I just need it for cross-browser testing on sites I build and on the rare occasion a page only works in IE. I don't really want to use a virtual machine, but would be ok with something standalone like tredosoft's, but I'm not aware of something like that for current versions of IE.

  Read the article

• Need advice in setting up server. fastCGI, suExec, speed, security, etc.

  - by lewisqic

  I am running my own dedicated server with centOS 5 and WHM/cPanel. I would like to configure my server to meet my needs but I need a little help. It will only be my own websites being run on this server. I'm still a little green when it comes to server administration so please forgive my ignorance. What I Would Like to Have: I need some public directories to be writable (for user image uploads and things like that) but I don't want those directories to have 777 permissions. I need individual accounts to have the ability to set custom php settings for their own account without affecting other accounts, whether through a php.ini file or through .htaccess or any other method. I would like things to run as fast as possible, whether that means using a php optimizer or cacher, such as eaccelerator or xcache or anything else. I need things to be as secure as possible. Here Are My Questions What should I use for my php handler? DSO? CGI? fastCGI? suPHP? Other? Should I be using suEXEC? What are the benefits or downfalls of this? What php optimizer/cacher is best to use? Are there any other security tips I need to know about all of this? I'd appreciate any advice or direction that can be offered. Thanks!

  Read the article

• Ubuntu 12.04 Very slow especially with Android Studio

  - by Nada

  I have an old laptop with the following specification: Memory: 485 MiB, Processor: Genuine intel CPU T2300 @ 1.66 GHz ×2, OS Type: 32 bit, Disk: 78.1 GB, I installed on it Ubuntu 12.04 LTS and I noticed that the overall system is very slow in responding. I tried to search about that in the internet and I found some articles talking about how to make Ubuntu 12.04 LTS run fast I applied all what they said including download LXDE desktop environment and then nothing different in the system response time. Then I need to develop some android applications so, I download Android Studio (Beta) 0.8.6. The problem became worse than before whenever I tried to open the Android Studio the screen is frozen for some minutes then it took time to download the projects and initialize the work space also, when I tried to move the cursor he is move very slowly. When I tried to run my first application on the AVD it took three hours and still not run yet. I delete the Android Studio and install it again several times, I was trying to solve the problem but still nothing change. Please if you have any suggestions that may help me make my laptop and Android Studio work faster I will appreciate it for you. Thank you in advance.

  Read the article

• Load is 0, yet site crawls (sometimes). What gives?

  - by Yegor

  I have a ~1.5-2mil page views per day site running on 2 servers. One for mysql, other for everything else. Mysql box has a load of 3, frontend is usually 0.0-0.1. Both are dual quad core with 8GB ram running SAS drives in raid5. CPU is idle for majority of the time, iowait is non-existent. Im running nginx, memcache, and site is built on php. Half the time everything runs perfect, while at other times it lags something severe, when it takes 10-15 seconds for a page to load. Page execution time is always super low, but it seems to hang, waiting for something before it actually loads the page. Whats even more weird is that it only happens to 1 file on the site (but its the one thats most commonly accessed, that actually loads the content on the site). Other pages are super fast at all times, even when it takes 15 seconds to load actual content. I have nginx_stats plugin installed, and if I monitor it, the lag spikes happen when the write column starts going above 100, and it frequently does... all the way to 500-1000. It does so at totally random times... not when traffic is heavy... it can do this in the middle of the night, and work perfectly at 5pm when traffic is at its highest. Any ideas?

  Read the article

• Windows won't boot after moving house. How do I solve this?

  - by James

  Ive just moved house and tried to set up my desktop after packing it away and now when I power it on, the BIOS boots up and no errors are found but when my computer tires to boot into Windows 7 a continuous fast beeping sound is made and a black screen is displayed. What I've done so far: Reset to UEFI defauts Played about with RAM, I had 4*4 GB sticks, I took all of them out to test for a mobo error which I have and now im only using 1 stick of 4 GB. Changed my GPU, I tok my gtx580 out and now im using the onboard Intel 3000 graphics driver, the BIOS and uefi are correctly displaying so I no longer think its a GPU based error. Ive check all of the connections and nothing seems to be loose. My HDD setup is: 2 128 GB SSD's in Raid 0 as my main C drive (possibly cause of error?) 1 1 TB Games drive 1 2 TB Data Drive Ive also got a blueray drive connected. After searching the internet im pretty much out of suggestions but im currently downloading a live CD to see if it will boot and if I can access some files on my HDD.

  Read the article

• Hyper-v and sql server connections for web apps

  - by Rick Ratayczak

  I have a physical machine running win8, and two VMs in hyper-v client: 1 web server, 1 sql server. The web server works fantastic. The sql is the one that is giving me the problem. I can connect to it with server explorer in visual studio or management studio just fine, and it's blazing fast. The problem happens when I use the same connection string I am using in visual studio server explorer in the web.config for an app. data source=VMSQL1;initial catalog=OtherShell;persist security info=True;user id=OtherShell;password=****;network library=dbmssocn;MultipleActiveResultSets=True;App=EntityFramework I made sure it was also using tcp-ip, but it doesn't connect with or without the network library part of the connection string. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) This is driving my batty for the last two days, any ideas? It fails from the web vm too, but works in management studio with the same connection string.

  Read the article

• System With Two Network Adapters

  - by Synetech inc.

  Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

  Read the article

< Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >