Search Results

Search found 13119 results on 525 pages for 'tcp ip'.

Page 186/525 | < Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >

• Best way to split LAN computers on two WANs (not load balancing)

  - by lpfavreau

  What is the best way to split the computers of a LAN (about 50 computers) to go on two WANs, depending on the computers' IP address or computers' configuration (gateway). I'm not looking for load-balancing, I need to be able to route which computer uses which Internet connection. A solution would be to rewire the old office to split the two distinct groups that need to use two different Internet connections but I'm not sure it's worth it at the moment. I have a pfSense router configured with the LAN (DHCP), WAN1 and WAN2. I also have the IP addresses (and ability to configure) the next router on WAN1 and the one on WAN2. What would you suggest? Routing based on IP addresses ranges? Different gateways? VLANs would be difficult for the same reason as to why rewire is a bit complicated. Thanks!

  Read the article

• Client can't reach my production webserver. It's their ISP's fault, but now what?

  - by MikeN

  I have a customer in Michigan who can't access my production SaaS webserver that is hosted on Slicehost. All other companies across the US/Canada/Europe have no problem reaching the site. This problem is occuring intermittantly, and Slicehost customer service says it's a problem with the client's ISP. I got the IP address of my client, and ping'ing that IP address from my PROD server fails, but ping'ing the IP address from my dev box or our seperate blog server (also hosted on slicehost) works. How do I debug a problem like this? I asked the client to reach out to their local ISP and ask about this problem. A traceroute shows that the packets are getting stopped on a Comcast Michigan node which is the client's ISP. Is there anything I can do additionally to fix this problem for my client?

  Read the article

• configure HTTPS server on a cisco router

  - by Sara

  For the past week I was trying to configure an HTTPS server on a cisco 2900 router, I've used the following commands and assigned a username and password to privilege 15 however, when Im trying to access a given ip it requires a username and password however when I insert the username and password I configured it does not allow me to enter and i'm not sure where the problem is. Router(config)# ip http secure-server Router(config)# ip http authentication local These were the commands i used for the https server and also I used the following to assign the username and password Router(config)#username name privilege 15 secret 0 password where 'name' and 'password' represent the username and password respectively I'm trying to access the 192.168.14.1 interface on the router and the username and password i created are not authorized to enter (I got the commands from a cisco router manual)

  Read the article

• PHP/mail : server sends email originating from wrong domain

  - by Niro

  I have a Mediatemple dv (Plesk) server with two domains, each has static IP. I had domain1 as main domain and domain2 as secondary. When A PHP script from domain2 sends email the headers show the IP address of domain1 as the origin. Received: from domain2.com (domain1.com [70.ipof domain1]). I want only domain2 to be mentioned so I did the following: Changed server name to domain2.com made domain2.com the primary domain (about 30 hours ago) made fixed IP address of domain2.com the default address for the server. Still when the script sends emails I see the same info as above in the header. What do I need to do to make the email origin domain2.com?

  Read the article

• pptp VPN, routing

  - by Adrian

  Details: eth0 = current internet port pptp1 = VPN connection, if I connect to my provider, he give me an IP address, which is accessible from the internet. This is what I need. I want to connect through this IP back to my PC. I want to keep my primary internet connection (eth0) on my PC for all traffic, but route traffic to VPN for specified application/or port, to access application/port from the IP, which I given from the pptp provider. Huhh? Difficult but, it is possible? If yes, how? Incoming port will be always: 33340 Outgoing port can be change, but usually it is 33330

  Read the article

• Can't access network share with name defined in hosts file

  - by Einar Egilsson

  I have a network share on a machine that I can only reach by IP address. I then defined an alias for the IP in my hosts file so I could use that instead of the IP but then I can't log on to the share, I just get the logon prompt again and again. So basically this: \\172.17.0.48\SomeShare works but this \\myalias\SomeShare doesn't. myalias is defined in c:\windows\system32\drivers\etc\hosts as 172.17.0.48 myalias And I can use the alias for remote desktop without problems. Can anyone tell me why this doesn't work for fileshares?

  Read the article

• Why is Server 2012 assigning "169.254.*.*" series when creating DHCP server?

  - by Seth

  I have a small office, with ATT Motorola modem (192.168.1.254) set as passthrough to Dlink DIR-815 (LAN 192.168.0.1) I am trying to setup DHCP server on Server 2012, and when I create new DHCP server, the title is created as 169.254.. instead of the domain name. (Domain clients can retrieve IP's as defined in the scope) Non-domain clients are not receiving IP's from the server but rather the Motorola... How do I assure DHCP setup is properly creating itself, and how do I make sure domain and non-domain clients get IP's from the server?

  Read the article

• Very slow loading pages with router

  - by user984621

  I bought new router - this one: http://www.tp-link.com/en/products/details/?model=TL-WR841ND and the problem is, that the loading pages is so slow, even sometimes the pages aren't loaded at all. Is the same, when I have on the Mac OS or Windows. Below are the informations from the router-admin section: LAN IP Address: 192.168.2.1 Subnet Mask: 255.255.255.0 WAN IP Address: 192.168.1.100 Dynamic IP Subnet Mask: 255.255.255.0 Default Gateway: 192.168.1.254 DNS Server: 89.203.178.2 , 10.14.2.1 How can I fix this problem? Is almost impossible to use the internet this way.

  Read the article

• Ways to do simple failover with one server and two IPs

  - by CrassHoppr

  The setup is one server (Windows 2008) at one location with two incoming connections. As the server has to interface with various on-site devices, and will have a small number of incoming connections, a data center is not an option, and instead cable/dsl connections must be used. The goal is that users visit https://service.site.com and are sent to either the primary IP address or a secondary IP if the primary is down. I've seen advice to use round robin DNS for this, but caching an IP for a downed interface is something I'd like to avoid. Is something like this possible with these constraints?

  Read the article

• Cisco NAT + IPSec + Web Server Configuration Question

  - by zagman76

  Hello - I currently have a Cisco 881W, and it is configured with one of our static IPs to do basic NAT for the network. We also have a web server that needs it's own IP. I configured the NAT for the 2nd IP, however now traffic through our IPSec VPN doesn't route to the web server properly (well, it routes to the internet, rather than through the Tunnel). I followed the instructions here: http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080094634.shtml But now the outbound NAT doesn't seem to be working properly - it keeps going to the NAT of the Cisco, and not the designated IP address. If anyone can assist, I would appreciate it greatly. Let me know what you need, and I'll get it to you! Thanks!

  Read the article

• Cant access EC2 hosted website

  - by Himanshu Page

  For some reason, I am unable to access our website www.doccaster.com (Bad request nginx). We are hosted on amazon EC2 with elastic ip associated to it. The weird part is a) I can access it through the public dns url http://ec2-184-73-195-180.compute-1.amazonaws.com b) My co founder who is located in another city can access it via www.doccaster.com. I observed that my instance was failing reachability check, so I launched a new one and assigned it the the elastic ip. I tried to ping the ip address 184.73.195.180 from my machine but no success. Any help will be really appreciated. More details I ran the following command on my server netstat -lntp | grep -E 'apache|httpd' and it displays :::80 for httpd . Is this accurate ? Should it be 0:0:0:80 ? or doesnt matter?

  Read the article

• Wireshark Not Displaying Packets From Other Network Devices, Even in Promisc Mode

  - by eb80

  System Setup: 1. MacBook running Mountain Lion. 2. Wireshark installed and capturing packets (I have "capture all in promiscuous mode" checked) 3. I filter out all packets with my source and destination IP using the following filter ("ip.dst != 192.168.1.104 && ip.src != 192.168.1.104") 4. On the same network as the MacBook, I use an Android device (connecting via WiFi) to make HTTP requests. Expected Results: 1. Wireshark running on the MacBook sees the HTTP request from the Android device. Actual Results: 1. I only see SSDP broadcasts from 192.168.1.1 Question: What do I need to do so that Wireshark, like Firesheep, can see and use the packets (particularly HTTP) from other network devices on the same network?

  Read the article

• Connecting guest OS to host os internet connection hyper-v

  - by autrevo

  Hyper-V internal switch and VM OS interfacing with Guest OS and IP Cofiguration When configuring hyper-v internal switch, Apart from physical lan adapter (say adapter 1), I see another LAN adapter (say adapter 2) added in host os. And we already have one virtual lan adapter in guest os, (say adapter 3) . adapter 1 is connected to internet with defaulty gateway say, 192.168.0.254 and uses class C IP. By con configuring adapter 2 and 3, I need to acheive two purpose - Access internet in guest os. seemlessly share files & folders between guest and host OS. Please, suggest, What is the best way to configure IP of these three adapters ?

  Read the article

• Windows 2003 server RRAS on VPC

  - by Saif

  I'm trying to setup a L2TP VPN server(to give user access on to all my VPN instance) on a Windows 2003 instance running on my VPC. While trying to enable RRAS I'm getting error, "less than two network interfaces were detected on this machine". Eventually it's because there's only one network interface available, the which has private IP. I have elastic IP assigned to this instance as well. But RRAS can't see this. What should I do to RRAS to be able to see the interface with elastic IP?

  Read the article

• OpenBSD Routing Problem

  - by Ozkan SENOVA

  I am running OpenBSD on a network appliance hardware. It has 5 NICs. I want to give different IP's in same subnet to 3 nics. Eg: em0: 192.168.1.5 em1: 192.168.1.90 em2: 192.168.1.56 I make the necessary configuration with ifconfig, all interfaces works as expected when all the ethernet ports are plugged in to switch. But there is something wrong in routing. If I connect to 192.16.1.5 via any service(http, smtp etc.), traffic goes over link#3. If I unpug the cable from em2 I can't reach any IP's binded on device. Is there any way to route traffic over different links in this IP configuration?

  Read the article

• Get the "source network address" in Event ID 529 audit entries on Windows XP

  - by Make it useful Keep it simple

  In windows server 2003 when an Event 529 (logon failure) occures with a logon type of 10 (remote logon), the source network IP address is recorded in the event log. On a windows XP machine, this (and some other details) are omitted. If a bot is trying a brute force over RDP (some of my XP machines are (and need to be) exposed with a public IP address), i cannot see the originating IP address so i don't know what to block (with a script i run every few minutes). The DC does not log this detail either when the logon attempt is to the client xp machine and the DC is only asked to authenticate the credentials. Any help getting this detail in the log would be appreciated.

  Read the article

• Routing based on source address in Windows Server 2008 R2

  - by rocku

  I'm implementing a direct routing load balanced solution using Windows Server 2008 R2 as back-end server. I've configured a loopback interface with the external IP address. This works, I am receiving packets with the external IP address and respond to them appropriately. However our infrastructure requires that traffic which is being load-balanced should go through a different gateway then any other traffic originating from the server, ie. updates etc. So basicly I need to route packets based on source address (external IP) to another gateway. The built-in Windows 'route' command allows routing based on destination address only. I've tried setting a default gateway on the loopback interface and mangled with weak/strong host send/receive parameters on the interfaces, however this didn't work. Is there any way around this, possibly using third party tools?

  Read the article

• How to install Gitlab in a VM on a production server?

  - by Michaël Perrin

  I have a production server running Ubuntu 12.04 and I would like to install on it a VM with Gitlab (using Vagrant and Virtualbox). Let's say that the address to access Gitlab is gitlab.mydomain.com . The DNS zone has been configured to point to the IP address of the server. I want users to be able to access to Gitlab (either for pushing to a repository, or for accessing to the web interface) from the outside. The VM has been configured to have an IP address. It means that when browsing http://gitlab.mydomain.com for instance, the request has to be forwarded to the VM on the server, ie. to the VM IP address. What are the ways to configure this? Can Apache be used as a proxy? In this case, I guess it only works for HTTP requests, but not for pushing to a Git repository on the VM.

  Read the article

• How to do port forwarding in D-link Glb802c?

  - by Manish

  I have some questions about port forwarding on my D-Link Router GLB-802C. For example: My local machine's IP is 117.1.1.81 My router's IP is 117.1.1.1 My Public (Web) IP is 117.16.1.1 My questions are: What will be my Global Address 'To'? What will be my Global Address 'From'? In Destination Port "From" and "To" what do I select in the drop down list and port no for forwarding HTTP traffic (for my website)? In Local Port, what do I select in drop down list and port no?

  Read the article

• Remote access to a KVM Ubuntu virtual server

  - by Lee

  I've just setup an ubuntu virtual server and everything seems to be working fine. I used KVM to get it working with a bridged network. I've given the virtual server a static ip address on my network. I don't seem to be able to connect to the virtual machine though from outside my network. If I'm on my own network it all works fine, I can ping the ip and connect to it. The virtual server can ping other machines and sites on the internet. I changed the port forwarding rules on my router to forward any connections on a specific port to the virtual server ip address thinking that was the problem, but it was still the same. Is there something I'm missing here which is blocking outside connections to the virtual machine? Thanks.

  Read the article

• How do I add client computers to a Windows SBS 2008 domain?

  - by Jonas

  We have a LAN and the router is the DHCP server. We have a server with Windows SBS 2008, it has the IP address 192.168.1.2 while the router has the IP address 192.168.1.1. I have set "DNS Relay" on the router to 192.168.1.2. I have tried to add a client computer to the SBS domain by visiting http://connect from the client computer. But that page doesn't exist. I can visit http://192.168.1.2/ then the default startpage for IIS7 is shown. I'm logged in as a local Administrator on the computer that I tries to add to the domain. How do I add the client computer to the SBS 2008 domain? The router is an D-Link DFL 200, and I have now set the "DNS Relay" to "Use address of LAN interface" instead of a specific IP-address. But it doesn't work.

  Read the article

• ts_block.vbs and mac intosh

  - by Eric Le breton

  I am using your excellent ts_blocker, release 20120530, on my server 2008 R2 Enterprise. it works very fine, i use the vbs script, launched with wscript. The only problem is that is does not work for users attempting to connect RDP from a mac intosh. With this machine the distant IP seems to be not recognized when the login fails. The IP is visible when the login is good (event ID 4624) but not when it fails (Audit failure event ID 4625) : then the IP is not to be seen in the event log ! In the "network information" of the event log entry is nothing given. Have you already been told of that and is there something to do ?

  Read the article

• Failover NIC with Windows 7 running Apache Server

  - by Benjamin Jones

  I have a Apache Server running on a Windows 7 Desktop for a internal website (Intranet). I am trying to figure out how I can make this system as failover safe as possible. One thing I want to do is use the 2nd NIC card that is currently disable. I only have one gateway address to my router. I do not have any computer running a Server O/S. If NIC1 crashes by chance(just humor me!), how could NIC2's IP take on the host name (I have mapped in host file) . I don't really care if the static IP of NIC2 changes seeing that the host name is the only thing I need. Could I add two IP's to the host file, with same host email and maybe create some script that will run IF NIC 1 fails? OR is there any failover software that will do this for me?

  Read the article

• Internet connection sharing windows server 2008 R2

  - by This is it

  I have one windows server 2008 r2, and that server has 4 network interfaces (3 private, 1 internet connection). I would like to share internet connection with other 3 networks. Windows server firewall should make logs of data that is transfered. It should not be possible to connect directly to private networks from internet. How could I do it? Edit: I tried with NAT in RRAS, but it doesn't work. Here is the configuration: Server: IP private:192.168.0.1 IP public: xx.xx.xx.xx client IP:192.168.0.2 Default gateway: 192.168.0.1 Public and private interface added in NAT section of RRAS.

  Read the article

• How can I make my Ubuntu server accessible to the internet ?

  - by wahid

  Hi, I already installed applications to make my server web server. when I type the DHCP released ip address in the web browser, i can access it but all it says is "it works....etc". I can copy files to /var/www successfuly using WINSCP but yet, i can not see any files when I connect to it using my windows machine in the browser. Secondly , I tried to forward port on my home SMC router, it only accepts local lan ip which my ubuntu server picks up internet ip from router...what should i do ? can you help please ???? Thanks,

  Read the article

< Previous Page | 182 183 184 185 186 187 188 189 190 191 192 193  | Next Page >