Search Results

Search found 9088 results on 364 pages for 'after power failure'.

Page 188/364 | < Previous Page | 184 185 186 187 188 189 190 191 192 193 194 195  | Next Page >

• APCUPSD and Hyper V R2

  - by Jason Berg

  I'm about to deploy a Windows Server 2008 R2 machine with the Hyper V role. I'd like to get away from having to use a network management card with my APC UPS as I'm only shutting down 1 server (it just seems like an unneeded point of failure). I'd like to look into using apcupsd instead. Will this work properly if I use a serial connection? Have you got it working yourself? How is the SNMP monitoring? I really like being able to easily monitor my UPS with SNMP when powerchute is installed. Will I be sacrificing this completely? Is the network management card really the way to go with this? If so, why? Bonus question: Is there a better UPS out there that I should be recommending in the future?

  Read the article

• Problem with testsaslauthd and kerberos5 ("saslauthd internal error")

  - by danorton

  The error message “saslauthd internal error” seems like a catch-all for saslauthd, so I’m not sure if it’s a red herring, but here’s the brief description of my problem: This Kerberos command works fine: $ echo getprivs | kadmin -p username -w password Authenticating as principal username with password. kadmin: getprivs current privileges: GET ADD MODIFY DELETE But this SASL test command fails: $ testsaslauthd -u username -p password 0: NO "authentication failed" saslauthd works fine with "-a sasldb", but the above is with "-a kerberos5" This is the most detail I seem to be able to get from saslauthd: saslauthd[]: auth_krb5: krb5_get_init_creds_password: -1765328353 saslauthd[]: do_auth : auth failure: [user=username] [service=imap] [realm=] [mech=kerberos5] [reason=saslauthd internal error] Kerberos seems happy: krb5kdc[](info): AS_REQ (4 etypes {18 17 16 23}) 127.0.0.1: ISSUE: authtime 1298779891, etypes {rep=18 tkt=18 ses=18}, username at REALM for krbtgt/DOMAIN at REALM I’m running Ubuntu 10.04 (lucid) with the latest updates, namely: Kerberos 5 release 1.8.1 saslauthd 2.1.23 Thanks for any clues.

  Read the article

• hp smart array lock up code 0x15, what is that? (or where can I get a list of descriptions of HP smart array controller lock up codes)

  - by user47650

  Hi, I've had a couple of Dl180 6g boxes hung over the last week, each have a P410 smart array controller. upon reboot the server has indicated that a controller failure event occurred and the previous lock up code was 0x15 - the server rebooted without issue. However there was nothing in the IML log, but the ADU report provided the following; Trap Address High Or Post Results Lockup Reason Or Post Error RIS Updates Or Post Error Detail Firmware Version Trap Address Low 0x8087 0x0015 0x0000033e 0x015e 0xd65c any suggestions on what that code is, my google fu failed. And hp support have not responded with any detail as yet.

  Read the article

• sqlcmd won't execute - Claims Native Client not installed properly

  - by nuit9

  I'm trying to use sqlcmd to execute some SQL scripts. Using a test command with a simple query like: sqlcmd -S HOSTNAME -d MYDATABASE -Q 'SELECT Names FROM Customers' sqlcmd does not appear to make any attempt to connect to the server as it displays this message: Sqlcmd: Error: Connection failure. SQL Native Client is not installed correctly. To correct this, run SQL Server Setup. The native client was presumably installed as part of the SQL Server setup and likely correctly. I actually get this message on any machine with SQL server installed trying to use sqlcmd so it's not a matter of the installation being corrupt. Unfortunately the message really tells me nothing about the problem so I don't know what the real issue is. I know the SQL Native client is working properly since a vbscript was able to execute SQL queries against the database. Is there some additional configuration needed to use sqlcmd?

  Read the article

• mac osx cannot connect to windows 7 machine

  - by Binary X

  I have a Mac OSX (Snow Leopard 10.6.6) setup on a network with several Windows 7 machines. When trying to place a large file on a Windows share the connection to the Windows share gets lost and I am unable to reconnect until I reboot the Mac. I know this is on the Windows side because the Mac can connect and transfer files to Server 2008 and XP without issue. Looking in the log file I see this message SharePointBrowser::handleOpenCallBack returned 12 I have tried restarting the com.apple.netauth.sysagent service but that did not resolve the situation. I can do an nslookup to the Windows 7 machine, but trying to ping the machine by hostname always gives a hostname lookup failure (I can ping via IP address). I cannot connect to the machine via IP adress either. Any help would be appreciated.

  Read the article

• PAM_LDAP error trying to bind ?

  - by billyduc

  I have this error when I ssh to my LDAP client using the login name on the LDAP server my LDAP client's running Ubuntu 9.10 Karmic my LDAP server is Fedora Core 4 and running Fedora Directory Server ssh [email protected] cat /var/log/auth.log //on the client Dec 18 10:24:17 ubuntu-ltsp sshd[4527]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=billyhost.local user=billyduc Dec 18 10:24:17 ubuntu-ltsp sshd[4527]: pam_ldap: error trying to bind as user "uid=billyduc,dc=mydomain,dc=com" (Invalid credentials) Dec 18 10:24:18 ubuntu-ltsp sshd[4527]: Failed password for billyduc from 192.168.5.121 port 51449 ssh2 Here's my /etc/pam.d/sshd cat /etc/pam.d/sshd auth [success=1 default=ignore] pam_unix.so auth required pam_ldap.so use_first_pass auth required pam_permit.so account sufficient pam_permit.so I also edit my /etc/ssh/sshd_config in both client and Server PasswordAuthentication yes So I think something wrong with the password when the ssh server do checking

  Read the article

• migrating puppet clients to a new puppet master (old puppet master server gone, only using backup)

  - by user47650

  My puppet master server had a hardware failure, and I have restored to another box. However this box has different hardware and hostname. If I restore the existing /etc/puppet directory to the new server, the puppetmaster will not start with the following error; # puppetmasterd --debug --verbose Could not prepare for execution: Retrieved certificate does not match private key; please remove certificate from server and regenerate it with the current key So what steps do I need to take to allow the new puppetmaster to start, and to generate a new puppetmaster certificate using the old ca.. Also will the puppet clients actually report in to a different puppet server using a server certificate that has been generated with the old CA?

  Read the article

• How to troubleshoot a GPF?

  - by AngryHacker

  I get a GPF dialog box out of the blue fairly often (like about 2 hours after I turn on the computer). It basically says that svchost.exe had a failure... (see the corresponding Event Log entry below). Event Type: Error Event Source: Application Error Event Category: (100) Event ID: 1000 Date: 5/18/2010 Time: 7:41:16 PM User: N/A Computer: DKHA-IPSA Description: Faulting application svchost.exe, version 5.1.2600.5512, faulting module ole32.dll, version 5.1.2600.5512, fault address 0x0004eaa9. Shortly after this error pops up, the computer pretty much grinds to a halt (e.g. some UI elements on the desktop simply do not respond). And I have to do a hard reboot. How do I troubleshoot this type of thing? P.S. The PC has all the latest patches and nothing is missing in the Device Manager.

  Read the article

• Oracle: FRM-41211 Error Message when starting a Report from Oracle Forms (64 Bit Windows Server)

  - by DB.

  After installing Oracle Forms and Reports 6.0 (Patch 18) on a Windows 2008 64 Bit server we get the following error when we try to start a report from Forms. "FRM-41211 integration error: ssl failure running another product" The problem is reproducable on another server using the same Windows OS. One of the proposed solutions (extending the REPORTS60_PATH) we have already tried but that did not help solving our problem. Another tip has been to shorten the content of the path variable before installing Oracle Forms and Reports. We will try this later on another server. Any other tips or solutions for this error would be very much appreciated.

  Read the article

• OCS 2007: Issues with /LiveServer/MCUFactory

  - by routeNpingme

  I'm not really an Office Communications Server expert, but just trying to resolve some seemingly minor issues with a new install... The following error is occurring in the OCS event log, and when I try to visit https://servername:444/LiveServer/MCUFactory in Internet Explorer to test the address, I just get a "page cannot be displayed" error. I can telnet to port 444 on the server and verify that the port is open and listening. Any ideas? Event Type: Error Event Source: OCS MCU Infrastructure Event Category: (1022) Event ID: 61013 Date: 7/28/2009 Time: 8:47:42 AM User: N/A Computer: COMM2 Description: The process DataMCUSvc(1284) failed to send health notifications to the MCU factory at https://servername:444/LiveServer/MCUFactory/. Failure occurrences: 29, since 7/28/2009 8:40:27 AM. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.

  Read the article

• PostgreSQL server: 10k RPM SAS or Intel 520 Series SSD drives?

  - by Vlad

  We will be expanding the storage for a PostgreSQL server and one of the things we are considering is using SSDs (Intel 520 Series) instead of rotating discs (10k RPM). Price per GB is comparable and we expect improved performance, however we are concerned about longevity since our database usage pattern is quite write-heavy. We are also concerned about data corruption in case of power failure (due to SSDs write cache not flushing properly). We currently use RAID10 with 4 active HDDs (10k 146GB) and 1 spare configured in the controller. It's a HP DL380 G6 server with P410 Smart Array Controller and BBWC. What makes more sense: upgrading the drives to 300GB 10k RPM or using Intel 520 Series SSDs (240GB)?

  Read the article

• ZFS SAS/SATA controller recommendations

  - by ewwhite

  I've been working with OpenSolaris and ZFS for 6 months, primarily on a Sun Fire x4540 and standard Dell and HP hardware. One downside to standard Perc and HP Smart Array controllers is that they do not have a true "passthrough" JBOD mode to present individual disks to ZFS. One can configure multiple RAID 0 arrays and get them working in ZFS, but it impacts hotswap capabilities (thus requiring a reboot upon disk failure/replacement). I'm curious as to what SAS/SATA controllers are recommended for home-brewed ZFS storage solutions. In addition, what effect does battery-backed write cache (BBWC) have in ZFS storage?

  Read the article

• Load-balancer options

  - by toolkit

  I am looking at a number of possible options for load-balancing. So far, I am constrained to the following options: DNS server load-balancer, balancing to a cluster of tomcat servers, with terracotta for session replication. Pros - don't have to buy new kit. Cons - DNS lb can keep directing to a broken server. Hardware load-balancer, direct to cluster of tomcat servers. Pros - could have second box for failover lb. Cons - expense. Apache server load-balancer. Pros - apache's lb polls for broken servers. Cons - apache server is single point of failure, plus need to buy another server. Are there any other options I should consider? Thanks. Update: Thanks for all the answers so far +1's all round. Not accepting an answer yet, to keep more ideas coming.

  Read the article

• LVM2 vs MDADM performance

  - by archer

  I've used MDADM + LVM2 on many boxes for quite a while. MDADM was serving for both RAID0 and RAID1 arrays, while LVM2 where used for logical volumes on top of MDADM. Recently I've found that LVM2 could be used w/o MDADM (thus minus one layer, as the result - less overhead) for both mirroring and stripping. However, some guys claims that READ PERFORMANCE on LVM2 for mirrored array is not that fast as for LVM2 (linear) on top of MDADM (RAID1) as LVM2 does not read from 2+ devices at a time, but use 2nd and higher devices in case of 1st device failure. MDADM reads from 2 devices at a time (even in mirrored mode). Who could confirm that?

  Read the article

• Gigabyte GA-P55A-UD4P won't boot from USB drive with RAID enabled

  - by Daniel Schaffer

  I've got a Windows 7 installation image on my USB hard drive, which is set up to be bootable. I know it works because I've used it on several computers, and it works on the computer I'm trying to install as long as the RAID controller is disabled. However, when I enable the RAID controller and attempt to boot from the USB driver, it hangs for 30-60 seconds and then gives me the "disk boot failure, insert system disk" error like it can't find any OS. Just for laughs, I disabled the RAID controller again and it booted fine. I'm having separate, unrelated issues burning a dvd with the ISO, so I would prefer to get this working.

  Read the article

• Why no "da-doomp" (disconnect notification sound) sometimes when unplugging wireless mouse receiver?

  - by DanH

  Sometimes (maybe one case in 3), when I unplug the wireless mouse receiver on my Sony VGN-CS215J laptop, there is no "da-doomp" sound, even after a minute or two. And if I plug the receiver back in there is no corresponding "du-dump" sound and the mouse is still (immediately) "live". This can happen when the activity light is out and there's nothing obviously going on -- it's not simply that the box is too busy. Other times one gets the expected behavior (and usually I get the correct behavior if I plug the receiver back in a few seconds and then unplug it after a "failure"). The reason this is significant is that if I get no "da-doomp" then the laptop will not sleep properly -- it will go to sleep initially, but then reawaken a few minutes later inside my laptop case and proceed to run the battery down (and no doubt overheat the unit). Any ideas?

  Read the article

• Regarding Reinstalling PostgreSQL

  - by Vivalavista

  I was using PostgreSQL 8.4. I tried removing it through Synaptic Manager and then I tried to install 9.1, but I still version 8.4. I deleted all the files associated with postgresql. Now I am unable to install any version of PostgreSQL. When I try I get this error: Setting up postgresql-9.1 (9.1.3-1~lucid) ... .: 12: Can't open /usr/share/postgresql-common/maintscripts-functions dpkg: error processing postgresql-9.1 (--configure): subprocess installed post-installation script returned error exit status 2 dpkg: dependency problems prevent configuration of postgresql: postgresql depends on postgresql-9.1; however: Package postgresql-9.1 is not configured yet. dpkg: error processing postgresql (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: postgresql-9.1 postgresql E: Sub-process /usr/bin/dpkg returned an error code (1) Please tell me the way to remove postgres completely so I can install a fresh version.

  Read the article

• Recovering OS X Mail Accounts Lost in Crash

  - by Tim

  I had a hard crash on my Mac PowerBook and when I restarted, Mail came up with only my MobileMe account still available and I cannot figure out how to restore the other eight email accounts I have. The directories in ~/Library/Mail all seem to be there. I even did an rsync of the modified .plist files from a TimeMachine backup of the directory from before the crash (unfortunately, I was on travel, so the backup is more than a week old and I'd like to try and recover from that point without having to entirely restore from TimeMachine). I also did a fix permissions. So my questions are where exactly is the account information for Mac Mail kept? Any thoughts of what might have caused the failure? Why does only MobileMe come up? Any other thoughts on how to fix things?

  Read the article

• Recommendations for distributed processing/distributed storage systems

  - by Eddie

  At my organization we have a processing and storage system spread across two dozen linux machines that handles over a petabyte of data. The system right now is very ad-hoc; processing automation and data management is handled by a collection of large perl programs on independent machines. I am looking at distributed processing and storage systems to make it easier to maintain, evenly distribute load and data with replication, and grow in disk space and compute power. The system needs to be able to handle millions of files, varying in size between 50 megabytes to 50 gigabytes. Once created, the files will not be appended to, only replaced completely if need be. The files need to be accessible via HTTP for customer download. Right now, processing is automated by perl scripts (that I have complete control over) which call a series of other programs (that I don't have control over because they are closed source) that essentially transforms one data set into another. No data mining happening here. Here is a quick list of things I am looking for: Reliability: These data must be accessible over HTTP about 99% of the time so I need something that does data replication across the cluster. Scalability: I want to be able to add more processing power and storage easily and rebalance the data on across the cluster. Distributed processing: Easy and automatic job scheduling and load balancing that fits with processing workflow I briefly described above. Data location awareness: Not strictly required but desirable. Since data and processing will be on the same set of nodes I would like the job scheduler to schedule jobs on or close to the node that the data is actually on to cut down on network traffic. Here is what I've looked at so far: Storage Management: GlusterFS: Looks really nice and easy to use but doesn't seem to have a way to figure out what node(s) a file actually resides on to supply as a hint to the job scheduler. GPFS: Seems like the gold standard of clustered filesystems. Meets most of my requirements except, like glusterfs, data location awareness. Ceph: Seems way to immature right now. Distributed processing: Sun Grid Engine: I have a lot of experience with this and it's relatively easy to use (once it is configured properly that is). But Oracle got its icy grip around it and it no longer seems very desirable. Both: Hadoop/HDFS: At first glance it looked like hadoop was perfect for my situation. Distributed storage and job scheduling and it was the only thing I found that would give me the data location awareness that I wanted. But I don't like the namename being a single point of failure. Also, I'm not really sure if the MapReduce paradigm fits the type of processing workflow that I have. It seems like you need to write all your software specifically for MapReduce instead of just using Hadoop as a generic job scheduler. OpenStack: I've done some reading on this but I'm having trouble deciding if it fits well with my problem or not. Does anyone have opinions or recommendations for technologies that would fit my problem well? Any suggestions or advise would be greatly appreciated. Thanks!

  Read the article

• MS Server 2003 Activiation Loop

  - by RPGonzo

  Recently we had a motherboard failure on a terminal server so we replaced the faulty motherboard, re-setup the RAID arrays (same motherboard but still wouldn't recognize old RAID setup) and continued to recover the system from a previous backup. No problem up to here, after restoring the system you are prompted to reboot and than login. On login we get a message box stating that Windows needs to be activated do you want to activate now, press yes but than the OS proceeds to log you off and do nothing at all. You can try over and over but to no avail. Found a few articles about a glitch in the activation script and how to reset it, tried that with the same results. Hoping someone can share some knowledge if you have seen this before? Thanks!

  Read the article

• Installation of Microsoft SQL Server 2008 R2 Developer Edition fails

  - by Yustme

  I'm having a problem installing MS SQL Server 2008 Developer edition on a Vista Ultimate 64 Bit machine. No matter what I try: I uninstalled the previous installation; I deleted all folders that where installed and had to do with SQL Server 2008; I cleared my registry using ccleaner; I tried 'fixit' utility from Microsoft uninstalling left overs; It just keeps failing at installing setup support files with this error message: SQL Server Setup failure SQL Server Setup has encountered the following error: Unknown property. [OK] I'm totally out of ideas. Any one has a suggestion for me to look at?

  Read the article

• Ubuntu Server 12.04 LTS on Hyper-V 2012

  - by user137533

  I have the following scenario: Hyper-V 2012 server core installation. On top of this i created a virtual machine on which i tried installing Ubuntu Server 12.04 which should not have any compatibility issues according to what Microsoft and Ubuntu are saying (although it is not officially supported). I start, run the installation and everything is ok, no problems detecting the network device or the hard drive (unlike debian which didn't even detect the hard drive). Once the installation is complete it asks me to reboot, it unmounts the "dvd drive" and reboots. Once it tries to start again i get the following error: Boot failure. Reboot and Select proper Boot device or Insert Boot Media in the selected Boot device. It seems to not be booting up from the virtual hard drive. The hard drive is set up in SCSI mode, nothing mounted on the IDE controller (no iso image or anything else. Does anyone have any ideas on what i can do to solve this?

  Read the article

• HP DL160 vs DL360 for virtualization

  - by Chris

  Hi, We're planning to consolidate our infrastructure (a dozen servers). We'll buy two or three identical new servers who will be setup as a XenServer pool. Load balancing and HA tools will monitor the pool and vMotion VMs in case of failure/overload. I know that the DL100 series of HP servers is cheaper than the DL300 serie (in every sense of the word). As we don't need local storage (we have a SAN) and can live with a temporary down server (provided that Xen Server HA tools work as advertized), what are the downsides going with the DL100 serie ? Thanks, Chris

  Read the article

• Can't login into Fedora 14 (XFCE) desktop. For the second time.

  - by bubba88

  Hello. I'm experiencing a problem with my Fedora 14 XFCE spin, which doesn't seem to let me pass the login screen: I enter my password for my user record, authentication passes (no 'Authentication Failure' message, which was when I tried to login as 'root' without root login enabled), and the screen becomes black (command line) for a couple of seconds and (voila!) my login screen emerges again. I did nothing to cause that, it just suddenly logged me out when I was editing window manager settings via XFCE's built-in GUI utility (choosing window decorations style, from the listbox on the left) For the first time, I had to boot from live CD and do a fresh install, but I don't really want to do that again :) Is there some way to repair this (maybe login via command line and reset window manager settings, I don't know really)? Thank you very much in advance!

  Read the article

• Fix bad blocks on Mac hard disk

  - by Andrew Vit

  I have a hard disk that I scanned with TechTool and it reports one bad block. As far as I can tell, TechTool only scans and reports a failure. It doesn't fix anything. Back in the day, Norton Disk Doctor did the job of scanning and flagging (remapping) bad blocks on the Mac. Today we have various tools for fixing up HFS+ directory errors (Disk Utility, fsck, DiskWarrior, TechTool), but I don't know of any tool that will do a surface scan and fix the bad blocks too. What software is available for this? If I know the address of the bad block, is there a low-level terminal utility for marking it?

  Read the article

< Previous Page | 184 185 186 187 188 189 190 191 192 193 194 195  | Next Page >