Search Results

Search found 8875 results on 355 pages for 'live broadcast'.

Page 188/355 | < Previous Page | 184 185 186 187 188 189 190 191 192 193 194 195  | Next Page >

  • wireless router - configuring for low-latency, high traffic environment

    - by Mark C
    Hey all, I have a few questions about configuring a router to achieve low-latency, high speed throughput on a local area network that is not connected to the internet. I've read up on some stuff, but thought I would solicit some opinions here on what I've found and what I want to know.... Turn off SSID broadcast - it produces extraneous packets that all clients receive and reply (?) to. Not a huge deal, but it may help a bit. Mixed-mode off - I should attempt to have all devices using the same standard (e.g. 802.11n) and turn mixed-mode off. Any thoughts on security? Does having WEP or any of the WPA variants actually increase latency? Nothing super secure is going over this LAN so if turning security off made things better, that'd be cool. Any other thoughts or things to focus on to create the low latency environment I'm trying to go for would be great. Links to webpages and papers are also cool. I'm open to go through a bunch of stuff. Thanks in advance!

    Read the article

  • Flow of packet in network

    - by user58859
    I can't visualize in my mind the network traffic flow. eg. If there are 15 pc's in a LAN. When packet goes from router to local LAN, do it passes all the computers? Means did it goes to ehernet card of every computer and those computers accept the packet based on their physical address. To which pc the packet will go first? To the nearest to the router? What happen if that first pc captures that packet(though it is not for it)? What happens when a pc broadcast a message? Do it have to generate 14 packets for all the pc's or only one packet reach to all pc's? If it is one packet and captured by first pc, how other pc's can get that? I can't imagine how this traffic is exactly flows? May be my analogy is completely wrong. Can anybody explain me this? Thanks in advance.

    Read the article

  • Why do I get access denied to data folder when using adb?

    - by gregm
    I connected to my live device using the adb and the following commands: C:\>adb -s HT829GZ52000 shell $ ls ls sqlite_stmt_journals cache sdcard etc system sys sbin proc logo.rle init.trout.rc init.rc init.goldfish.rc init default.prop data root dev $ cd data cd data $ ls ls opendir failed, Permission denied I was surprised to see that I have access denied. How come I can't browse around the directories using the commandline like this? How do I get root access on my phone?

    Read the article

  • java applet - javascript communication

    - by udhaya
    Applet Communication: write a small applet and embed it in html-file with following functionality. 1. change applet bg color by receiving a javascript command with the color parameter. 2. show dynamic mouse position in applet-window and display position in html-site. use live-connect between applet and browser communication.

    Read the article

  • SVN: Branches for Every Little Change?

    - by yar
    Hi. We have a client (who has a client, who has a client) who is driving us mad with change requests to a code base (in PHP). Our first response was to just work in a main trunk in SVN, but the client often comes back and requests that a certain change needs to get pushed to the live servers ASAP. On the other hand, other changes get reduced in priority suddenly, which originally came grouped with other changes (seemingly). We are thinking of using a branch for every change request. Is this mad? What other solutions might work? Thanks! Edit: This is a really hard question to choose the correct answer for. Thanks to everybody for your great answers. Edit: I know that the best answer I chose was not particularly popular. I too wanted to find a technical solution to this problem. But now I think that if the client wants software with features that can be deployed in a modular fashion... this problem should not be solved in our use of the version control system. It would have to be designed into the software. Edit: Now it's almost a month later and my coworker/client has convinced me that multiple branches is the way to go. This is not just due to the client's insanity, but also based on our need to be able to determine if a feature is "ready to go" or "needs more work" or whatever. I don't have the SVN with me, but we merge using the advice from the SVN Cookbook: you merge the branch from the revision it was branched to the head revision. Also, using this system, we merge all branches at some point and that becomes the new QA and then live build. Then we branch from that. Last Edit (Perhaps): Months later, this system is still working out for us. We create branches for every ticket and rarely have problems. On the other hand, we do try to keep things separate as far as what people are working on... Two Years Later: We use GIT now, and now this system is actually quite reasonable.

    Read the article

  • Configure static IPv6 on Ubuntu

    - by Charles Offenbacher
    I'm trying to configure IPv6 on a dedicated Ubuntu server. My provider gave me a "/64" (whatever that is - I'm still confused) of IPv6 addresses. However, when I try to use them, I can't ping anything. What do I do? :( # ping6 ipv6.google.com PING ipv6.google.com(vx-in-x63.1e100.net) 56 data bytes From fe80::219:d1ff:fefb:42d8 icmp_seq=1 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=2 Destination unreachable: Address unreachable From fe80::219:d1ff:fefb:42d8 icmp_seq=3 Destination unreachable: Address unreachable --- ipv6.google.com ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2014ms # tracepath6 ipv6.google.com 1?: [LOCALHOST] 0.025ms pmtu 1500 1: fe80::219:d1ff:fefb:42d8%eth0 2000.022ms !H Resume: pmtu 1500 # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet static address 64.***.***.*** netmask 255.255.255.248 gateway 64.***.***.*** iface eth0 inet6 static pre-up modprobe ipv6 address 2607:F878:1:***::1 netmask 64 gateway 2607:F878:1:***(same as address)::1 # ifconfig eth0 Link encap:Ethernet HWaddr 00:19:d1:fb:42:d8 inet addr:64.***.***.*** Bcast:64.***.***.*** Mask:255.255.255.248 inet6 addr: fe80::219:d1ff:fefb:42d8/64 Scope:Link inet6 addr: 2607:f878:1:***::1/64 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:52451 errors:0 dropped:0 overruns:0 frame:0 TX packets:39729 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:6817761 (6.8 MB) TX bytes:6153835 (6.1 MB) Interrupt:41 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:166 errors:0 dropped:0 overruns:0 frame:0 TX packets:166 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:31714 (31.7 KB) TX bytes:31714 (31.7 KB)

    Read the article

  • How to deploy a project developed in Tapestry5?

    - by shane87
    I have just completed a project as part of a college degree. However I would like to deploy the project and make it live. I am unsure of how to do this as I have never done it before? I know I need to buy a domain name and some server space to host the project. If anyone can point me in the right direction that would be great? Thanks in advance!

    Read the article

  • WOL doesn't work if set to anything other than `a` but this setting makes it boot all the time

    - by Elton Carvalho
    I manage a small "cluster" of 4 Xeon machines with Intel boards in my lab. They are all plugged to a 5-port 3-Com switch with static IP addresses like 10.0.0.x. They are all running OpenSuse 11.4 and their /home/ is served by one of the machines (node00) via NFS. They are plugged to an UPS that can keep them on for ca. 15 minutes, but there are lots of electric shortages due to "unscheduled maintenace" that are longer than this. So they end up being powered down without notice. If I set the BIOS to turn them on after power shortages, the issue is that they all boot at the same time and, if node00 decides to run fsck in the /home/ partition, it does not finish booting before the others try to NFS mount their /home/. I am trying to make wake on lan work, so I can choose to boot the NFS clients only after the server has successfully booted. The problem is that when I run ethtool I get an output like this: Supports Wake-on: pumbag Wake-on: g Theoretically, it is set to wake on MagicPacket(tm), according to the manual. But sending the WOL packet using wol -i 10.0.0.255 $MACADDR does not wake up the box after I shut it down with halt. The ethernet link led blinks after I send the packet, so it appears to be getting to the machine. However, if I set it up with ethtool -s eth1 wol bag, the machine always wakes up right after halting, even if I don't send the Magic packet. This means that the device can wake up with LAN activity, but seems to be ignoring the magic packet. Setting wol ag does not wake the box with the MagicPacket. Does setting wol a mean that it should boot with any broadcast message? How can I diagnose the issue of the machine not waking up with the MagicPacket even though I am sending it and it's set up to wake up with it? Thanks in advance!

    Read the article

  • RIA: Manipulate DOM

    - by stephanos
    I want to display a website embedded in my own site and modify the DOM (e.g. change a button's color/size), similar to what Firebug is capable of. I'm aware of the security issues that arise - my plan is to use this approach to do live website usability testing (A/B style). I'm not limited to any specific RIA framework (yet would prefer Flex) - but it has to work without installing anything (so no AIR). Cheers :-)

    Read the article

  • media center extended

    - by Gil Montag
    Hi, Where can I find resources related to writing your own media center extender client - i.e. an application that will run on another machine at home and remotely render vista's media center on it, allowing to stream movies, live tv etc Thanks, Gil

    Read the article

  • How to completely disable IPv6 for loopback interface on RHEL 5.6

    - by Marc D
    I've done lots of research on how to disable IPv6 on RedHat Linux and I have it almost completely disabled. However the loopback interface is still getting an inet6 loopback address (::1/128). I can't find where IPV6 is still enabled for loopback. To disable IPV6 I added the following settings to /etc/sysctl.conf: net.ipv6.conf.default.disable_ipv6=1 net.ipv6.conf.all.disable_ipv6=1 And also added the following line to /etc/sysconfig/network: NETWORKING_IPV6=no After rebooting, the inet6 address is gone from my physical interface (eth0), but is still there for lo: # ip addr show 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 00:50:56:xx:xx:xx brd ff:ff:ff:ff:ff:ff inet 10.x.x.x/21 brd 10.x.x.x scope global eth0 If I manually remove the IPV6 address from loopback and then bounce the interface, it comes back: # ip addr del ::1/128 dev lo # ip addr show lo 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo # ip link set lo down # ip link set lo up # ip addr show lo 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever I believe IPV6 should be disabled at the kernel level as confirmed by sysctl: # sysctl net.ipv6.conf.lo.disable_ipv6 net.ipv6.conf.lo.disable_ipv6 = 1 Any ideas on what else would cause the loopback interface to get an IPV6 address?

    Read the article

  • UDP blocked by Windows XP Firewall when sending to local machine

    - by user36367
    Hi there, I work for a software development company but the issue doesn't seem to be programming-related. Here is my setup: - Windows XP Professional with Service Pack 3, all updated - Program that sends UDP datagrams - Program that receives UDP datagrams - Windows Firewall set to allow inbound UDP datagrams on a specific port (Scope: Subnet) If I send a UDP datagram on any port to other, similar machines, it goes through. If I send the UDP datagram to the same computer running the program that sends (whether using broadcast, localhost IP or the specific IP of the machine), the receiver program gets nothing. I've traced the problem down to the Windows XP Firewall, as Windows 7 does not have this problem (and I do not wish to sully my hands with Vista). If the exception I create for that UDP port in the WinXP firewall is set for a Scope of Subnet the datagram is blocked, but if I set it to All Computers or specifically enter my network settings (192.168.2.161 or 192.168.2.0/255.255.255.0) it works fine. Using different UDP ports makes no difference. I've tried different programs to reproduce this problem (ServerTalk to send and either IP Port Spy or PortPeeker to receive) to make sure it's not our code that's the issue, and those programs' datagrams were blocked as well. Also, that computer only has one network interface, so there are no additional network weirdness. I receive my IP from a DHCP server, so this is a straightforward setup. Given that it doesn't happen in Windows 7 I must assume it's a defect in the Windows XP Firewall, but I'd think someone else would have encountered this problem before. Has anyone encountered anything like this? Any ideas? Thanks in advance!

    Read the article

  • very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

    - by gojira
    I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ethernet cable, everything is fine and I get extremely fast up- and download speeds. When I connect wirelesssly however, websites load extremely slow - it takes dozens of seconds to load a website! <-- This is my question, how can I fix the wireless speed issue? Gmail for example is unusable this way. I tried speedtest.net, but this always fails in the upload part of the test so I can't even test the bandwidth (could the fact that it fails in the upload part, not the download part, be an indication what the problem is?!). I have isolated the problem a bit, I am convinced it has to do either with the router itself, the router settings, or the settings of the wireless connection in Win 7. Because previously, I was using another router by Buffalo and I had no problems whatsoever. I have tried to reproduce the settings from the Bufallo router as closely as possible on the Linksys router (same channel, same encryption etc). The download speed problem only occurs with the Linksys router, and only in wireless mode! When I exchange the Linksys router with the Buffalo router I have here for testing, the wireless speed is up to normal again. Also, before I had installed the Tomato firmware I had exactly the same problem, so it has nothing to do with the firmware itself. Notes & things I already tried: Changing the channel: does not seem to affect anything, I am also on the same channel (10) which I was previously on when I had a Buffalo router. QoS is off. Ping to the router itself is OK, ~ 1 ms. Some current settings of the linksys router: WAN / Internet Type: DHCP Wirelesss Mode: Access Point B/G Mode: Mixed Broadcast: check Channel: 10 - 2.457 GHz Security: WPA2 Personal Encryption: AES

    Read the article

  • Strange WiFi problem - network is "not connected" but works

    - by GalacticCowboy
    Background I'm using a Windows XP tablet PC connected to my home network. I do broadcast the SSID, but otherwise the wireless network is locked down as tight as I can make it - WPA2 with a strong key, MAC filtering, etc. I've had this computer for about 4 years and the router for about 6 months. Before that, the previous router was set up in the same way, and I've never had any particular problems. Problem This morning - as I type this, as a matter of fact - Windows is reporting that none of my network connections are connected. Yet somehow my Internet connectivity still works! ipconfig reports a valid IP address, domain, etc., even though Windows apparently doesn't know about it. I tried repairing the connection and it had no effect - the repair eventually timed out. I'm pretty sure that I could reboot the computer and/or the router, etc. and it would fix the problem. However, I'm more interested in knowing if any of you have ever seen anything like this, and what might have caused it? Since it works I'm not inclined to mess with it too much. My concern is that it's a precursor to bigger problems.

    Read the article

  • Google App Engine with local Django 1.1 gets Intermittent Failures

    - by Jon Watte
    I'm using the Windows Launcher development environment for Google App Engine. I have downloaded Django 1.1.2 source, and un-tarrred the "django" subdirectory to live within my application directory (a peer of app.yaml) At the top of each .py source file, I do this: import settings import os os.environ["DJANGO_SETTINGS_MODULE"] = 'settings' In my file settings.py (which lives at the root of the app directory, as well), I do this: DEBUG = True TEMPLATE_DIRS = ('html') INSTALLED_APPS = ('filters') import os os.environ["DJANGO_SETTINGS_MODULE"] = 'settings' from google.appengine.dist import use_library use_library('django', '1.1') from django.template import loader Yes, this looks a bit like overkill, doesn't it? I only use django.template. I don't explicitly use any other part of django. However, intermittently I get one of two errors: 1) Django complains that DJANGO_SETTINGS_MODULE is not defined. 2) Django complains that common.html (a template I'm extending in other templates) doesn't exist. 95% of the time, these errors are not encountered, and they randomly just start happening. Once in that state, the local server seems "wedged" and re-booting it generally fixes it. What's causing this to happen, and what can I do about it? How can I even debug it? Here is the traceback from the error: Traceback (most recent call last): File "C:\code\kwbudget\edit_budget.py", line 34, in get self.response.out.write(t.render(template.Context(values))) File "C:\code\kwbudget\django\template\__init__.py", line 165, in render return self.nodelist.render(context) File "C:\code\kwbudget\django\template\__init__.py", line 784, in render bits.append(self.render_node(node, context)) File "C:\code\kwbudget\django\template\__init__.py", line 797, in render_node return node.render(context) File "C:\code\kwbudget\django\template\loader_tags.py", line 71, in render compiled_parent = self.get_parent(context) File "C:\code\kwbudget\django\template\loader_tags.py", line 66, in get_parent raise TemplateSyntaxError, "Template %r cannot be extended, because it doesn't exist" % parent TemplateSyntaxError: Template u'common.html' cannot be extended, because it doesn't exist And edit_budget.py starts with exactly the lines that I included up top. All templates live in a directory named "html" in my root directory, and "html/common.html" exists. I know the template engine finds them, because I start out with "html/edit_budget.html" which extends common.html. It looks as if the settings module somehow isn't applied (because that's what adds html to the search path for templates).

    Read the article

  • Umbraco, Macintosh and some working blog software

    - by Ardman
    I have a website that is using Umbraco as it's CMS. Everything is working great on a PC. Am able to use Windows Live Writer to create blogs with no problems at all. My problem comes when the Macintosh users try to blog. I have tried loads of different software packages, MarsEdit, Bloggo etc. but none seem to work. Has anyone had any joy with blog software on a Macintosh using Umbraco as the backend?

    Read the article

  • Why doesn't MongoDb store my slashes in this string?

    - by Rob Dudley
    Can anyone tell me why this command doesn't work from the MongoDB shell client: db.coll.update({'live':true},{$set:{'mask':"\D\D\D\D\D\D\D\D"}},false,true) but db.coll.findOne({'id':'someId'}) returns the mask field as: "mask" : "DDDDDDDD", Where are the slashes going? I've tried "double escaping" with \\D and that inserts both slashes: "mask" : "\\D\\D\\D\\D\\D\\D\\D\\D", MongoDB shell version: 2.0.6, MongoDB version: 2.0.5, OSX Lion Thanks

    Read the article

  • Why do I need a managed switch and which one should I buy?

    - by ascanio1
    I bought a 2nd router and I want both routers to have direct WAN access to the modem. One of the 2 routers directs VOIP traffic to a telephone line port. This VOIP service is provided by the cable carrier which also leases the modem & the router. The cable company technician told me that this VOIP line uses IPv6 addressing and therefore I must employ an IPv6 capable/compliant Giga Hub/Switch or my telephone line won't work anymore. Pls advise me (brand/model) an IPv6 compliant, 2 port, switch to purchase. Pls educate me: By reading this forum I thought that hubs broadcast traffic to all ports, regardless of which input/output is being used and so, theoretically, they have nothing to do with IP. Correct? Same story for unmanaged switches, where the only difference is that these latter devices route traffic only to those ports which are detected to be in use. Correct? I also understood that unmanaged switches route traffic simply by detecting hardware use and not by selecting specific IP traffic. Correct? Finally, there are managed switches which DO select traffic based on IP and, therefore, only these managed switches are involved with IPv6... Why would my cable company explicitly tell me, over and over, that I must use an IPv6 compliant switch? Why would they need a managed switch instead of an unmanaged one? Thanks in advance for helping me understand!

    Read the article

  • A Guide to Windows Hacking for Mac Users?

    - by Carlton Gibson
    I am a long-time Mac user looking to gain a decent understanding of Windows. I'm not really interested in the history except as it is still relevant to Windows 7. I'm competent with the Mac and UNIX/Linux environment. I'm live in C, Objective-C, Bash, Python, JavaScript, AppleScript and PHP. As such I want something that is introductory but not aimed at beginners. Can anyone recommend a decent book (or other resource) to get me started? TIA

    Read the article

< Previous Page | 184 185 186 187 188 189 190 191 192 193 194 195  | Next Page >