Search Results

Search found 18121 results on 725 pages for 'support esemenyek'.

Page 189/725 | < Previous Page | 185 186 187 188 189 190 191 192 193 194 195 196  | Next Page >

• wireless is disabled by hardware lenovo 3000g430

  - by sudheer

  sir i have problem with my wifi switch sir please tell me solution for my problem (wifi is disabled by hardware). output of sudo lshw -C network is sudo] password for sudheer: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: eth2 version: 01 serial: 00:21:00:72:3a:93 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:19 memory:f4700000-f4703fff *-network description: Ethernet interface product: NetLink BCM5906M Fast Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 02 serial: 00:1e:68:ad:24:0b size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=sb v3.04 ip=172.16.52.79 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:47 memory:f4600000-f460ffff output of iwconfig is lo no wireless extensions. eth2 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. sudheer@sudheer:~$ sudo iwlistscanning sudo: iwlistscanning: command not found ***sudheer@sudheer:~$ sudo iwlist scanning*** lo Interface doesn't support scanning. eth2 Failed to read scan data : Invalid argument eth0 Interface doesn't support scanning.

  Read the article

• OBIEE 11.1.1.6.5 Bundle Patch released Oct 2012

  - by user554629

  October  2012 OBIEE 11.1.1.6.5 Bundle Patch released Bundle patches are collection of controlled, well tested critical bug fixes for a specific product  which may include security contents and occasionally minor enhancements. These are cumulative in nature meaning the latest bundle patch in a particular series would include the contents of the previous bundle patches released.  A suite bundle patch is an aggregation of multiple product  bundle patches that are part of a product suite. For OBIEE on 11.1.1.6.0, we plan to run a monthly bundle patch cadence. 11.1.1.6.5 bundle patch- available for download from  My Oracle Support . - is cumulative, so it includes everything from previous updates- available for supported platforms ( Windows, Linux, Solaris, AIX, HPUX-IA ) Navigate to https://support.oracle.com and login- Knowledge Base tab  Select a product line [ Business Intelligence ]  Select a Task [ Patching and Maintenance ]  Click Search- Oct 23, 2012, OBIEE 11g: Required and Recommended Patches and Patch Sets, ID 1488475.1- 11.1.1.6.5 Published 19th October 2012 Note: The 11.1.1.6 versions on top of 11.1.1.6.0 are not upgrades, they are opatch fixes.  This is not an upgrade process like from OBIEE 10g to 11g, or from OBIEE 11.1.1.5 to 11.1.1.6.  It is much safer than applying any one-off fixes, which are not regression tested.  You will be more successful using 11.1.1.6.5.  

  Read the article

• How can you enable forms scripting for outlook 2010 on Citrix servers ?

  - by Florent Courtay

  I'd like to deploy Office 2010 on Citrix servers, but i can't enable form scripting support. With outlook 2007, it was solved by adding Outlvbs.dll in the office directory, and running msiexec /i {<Outlook GUID>} ADDLOCAL=OutlookVBScript /qb But it seems this does not work anymore with Outlook 2010, I get the following error : Error 2711. An internal error has occured. (OutlookVBScript). I don't get much help from microsoft support site, as there isn't a lot of informations on office 2010 yet. Have anyone succeded in installing and using outlook 2010 with form scripting in a citrix environment ?

  Read the article

• Trying to install Proprietory Nvidia Graphics Drivers

  - by Peter Snow

  After reading and trying many different suggestions for some hours, I returned to this how-to: https://help.ubuntu.com/community/BinaryDriverHowto/Nvidia The first problem I encounter is how to identify which of the listed drivers support my Nvidia GEForce 630M graphics card. Following the links doesn't really help, since it is not stated there either (except where support for a new driver was added later which is explicitly stated, but the original devices covered are not). However, even if I knew, if it doesn't appear in the 'Additional Drivers' dialogue (see below), how will I install it? Second Issue: The article goes on to say that available drivers for my hardware are usually listed in 'Additional Drivers'. In my case, they aren't. Unfortunately, it doesn't tell me how to correct that or work around it? I've checked the bios and there is no way offered there to disable the integrated graphics, only the Nvidia graphics. I've also tried each available option in this: $ sudo update-alternatives --config i386-linux-gnu_gl_conf My system is an Acer Aspire 4752G bought May 2012. I'm running Ubuntu 12.04LTS. uname -a : 3.2.0-38-generic-pae #61-Ubuntu SMP Tue Feb 19 12:39:51 UTC 2013 i686 i686 i386 GNU/Linux It's 64bit hardware but I installed 32bit OS for greater software compatibility. Running $ sudo tail -fn 500 /var/log/Xorg.0.log | grep '(EE)' returns" (WW) warning, (EE) error, (NI) not implemented, (??) unknown. [ 28.886] (EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found) The reason for wanting the proprietor y drivers is because my laptop comes with 3D accelerated graphics adaptor and so rather than confining myself to struggling with the on-board graphics, I would rather use it. I also want to experiment with using it for bitmining (which uses the GPU's for computing power).

  Read the article

• Isopropyl okay to use on MacBook screen?

  - by Archagon

  I've always used a mixture of isopropyl alcohol and distilled water to clean my computer screens (50% water and 50% * 70% isopropyl). From what I understand, these are exactly the same ingredients used in most commercial screen cleaners, perhaps even more diluted. I recently used this solution to wipe off my 2010 MacBook Pro screen, and there don't seem to be any problems, but this support page explicitly says not to use isopropyl. Now I'm worried that I might have inadvertently damaged something. I'm also concerned because I once managed to dissolve the surface rubber lining of one of my mice with the isopropyl solution, and the MacBook Pro display has a thin rubber bezel keeping the glass in place. Why would Apple single out isopropyl on their support page? Should I be concerned?

  Read the article

• EBS 11i- Új ÁFA törvényt követo lokalizációs csomag

  - by user552636

  Mai világunkban már hozzászokhattunk, hogy minden változik. Már meg sem lep bennünket, hogy az ÁFA törvény 2013-tól szintén módosul. Jó hír E-Business Suite 11i -t használó Ügyfeleink számára, hogy elkészült az adótörvények változásához kapcsolódóan (Art. 31/B §) az Oracle E-Business Suite 11i (11.5.10) verziójához az új lokalizációs ÁFA csomag, amely a 2013-tól az "Összesíto jelentés"-hez szükséges adatok eloállítását támogatja. Az új ÁFA csomag az alábbi három új kimutatás csoportot tartalmazza, amelyek a jelenlegi ÁFA megoldáshoz hasonlóan lehetové teszik a riport eredmények elozetes megtekintését, az eredmények véglegesítését, illetve szükség esetén másolati nyomtatás készítését: - "OHU: ÁFA analitika és összesíto jelentés 2013 (Elozetes)" - "OHU: ÁFA analitika és összesíto jelentés 2013 (Végleges)" - "OHU: ÁFA analitika és összesíto jelentés 2013 (Másolat)" A kimutatás csoportokban az alábbi programok lesznek elérhetok:  - OHU: ÁFA analitika kimutatás  - OHU: Belföldi összesíto jelentés partnerenként Az "OHU: ÁFA analitika kimutatás" funkcionális szempontból nem módosul, csak az ahhoz szükséges technikai módosítások kerülnek átvezetésre, hogy a kimutatás által összegyujtött adatok az "OHU: Belföldi összesíto jelentés partnerenként" kimutatás számára elérhetok legyenek. Az újonnan megjeleno "OHU: Belföldi összesíto jelentés partnerenként" kimutatás a NAV 1365A-01-05-ös összesíto és a 1365M lapok partnerenkénti kitöltéséhez szükséges adatokat listázza, a tervek szerint Excel formátumban, az adatokat a bevallás által kért eFt-ra kerekítve. (A riport adatok Excel formátumban történo megjelenítéséhez elofeltétel az Oracle BI Publisher termék telepítése). A lokalizációs csomagban korábban elérheto:  - "OHU: Levonható ÁFA megosztási kimutatás" és a kapcsolódó  - "OHU: ÁFA Fizeto pozíció bejegyzése" programok nem kerülnek aktualizálásra, mivel használatuk korábbi adó törvény változások miatt már nem szükséges. A 2013-ra vonatkozó ÁFA bevallások készítése során már az új "OHU: ÁFA analitika és összesíto jelentés 2013" kimutatáscsoportok futtatását javasoljuk, a korábbi ÁFA kimutatás csoportokat pedig használaton kívül kell helyezni. A 2013-tól használandó új ÁFA csomag az Oracle Support szolgáltatásán keresztül érheto el. Ügyfeleink a My Oracle Support-on 1713-as termékkódra (EMEA Add-on Localizations) megnyitott hibajegyen (SR) bejelentésével jelezhetik igényüket a fentebb részletezett lokalizációs csomagra.

  Read the article

• Looking for Team Development type Software like SVN

  - by SoLoGHoST

  I am in need of a software that is PHP-Based, or similar that can be installed on my server that doesn't offer SVN Perks. It should be somewhat similar to an SVN, however, since the server doesn't support SVN, we'll need another means of doing sort of the same thing. We have a team of Developers and need to accomplish progress in the same way that an SVN does, but without that type of server support. Is there any software that could be installed via webhosting that would be somewhat, if not exactly, similar to an SVN? Please help, Thanks :)

  Read the article

• Exalogic Elastic Cloud Software (EECS) version 2.0.1 available

  - by JuergenKress

  We are pleased to announce that as of today (May 14, 2012) the Exalogic Elastic Cloud Software (EECS) version 2.0.1 has been made Generally Available. This release is the culmination of over two and a half years of engineering effort from an extended team spanning 18 product development organizations on three continents, and is the most powerful, sophisticated and comprehensive Exalogic Elastic Cloud Software release to date. With this new EECS release, Exalogic customers now have an ideal platform for not only high-performance and mission critical applications, but for standardization and consolidation of virtually all Oracle Fusion Middleware, Fusion Applications, Application Unlimited and Oracle GBU Applications. With the release of EECS 2.0.1, Exalogic is now capable of hosting multiple concurrent tenants, business applications and middleware deployments with fine-grained resource management, enterprise-grade security, unmatched manageability and extreme performance in a fully virtualized environment. The Exalogic Elastic Cloud Software 2.0.1 release brings important new technologies to the Exalogic platform: Exalogic is now capable of hosting multiple concurrent tenants, business applications and middleware deployments with fine-grained resource management, enterprise-grade security, unmatched manageabi! lity and extreme performance in a fully virtualized environment. Support for extremely high-performance x86 server virtualization via a highly optimized version of Oracle VM 3.x. A rich, fully integrated Infrastructure-as-a-Service management system called Exalogic Control which provides graphical, command line and Java interfaces that allows Cloud Users, or external systems, to create and manage users, virtual servers, virtual storage and virtual network resources. Webcast Series: Rethink Your Business Application Deployment Strategy Redefining the CRM and E-Commerce Experience with Oracle Exalogic, 7-Jun@10am PT & On-Demand: ‘The Road to a Cloud-Enabled, Infinitely Elastic Application Infrastructure’ (featuring Gartner Analysts). WebLogic Partner Community For regular information become a member in the WebLogic Partner Community please visit: http://www.oracle.com/partners/goto/wls-emea ( OPN account required). If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Mix Forum Wiki Technorati Tags: ExaLogic Elastic Cloud,ExaLogic,WebLogic,WebLogic Community,Oracle,OPN,Jürgen Kress,ExaLogic 2.0.1

  Read the article

• opengl libraries for ubuntu running on Virtual Box

  - by vboxuser

  I am having Ubuntu 10.04 running on VirtualBox. Guest additions are installed successfully. But Guest additions do not provide the OpenGL library. To run open GL demo what needs to be installed. Some google links suggest Mesa utils. By my understanding is Mesa utils do not use vbox drivers to achieve hardware acceleration. Ubuntu 10.04 is running on VirtualBox and not on bare metal. The host comprise of Zx400 CPU with nvidia graphics driver. But this is not relevant since I would be using the vbox drivers provided by guest additions on VirtualBox. In this scenario how do I get OpenGL libraries on Ubuntu?. (Specially I am looking for solution other than Mesa, since mesa has support only for VMware and not for VirtualBox) How to get Opengl libraries which use vbox drivers for 3D hardware accleration?? As i already mentioned, ubuntu 10.04 is running on VirtualBox and not on bare metal. the host comprise of Zx400 CPU with nvidia graphics driver. but this is not relevant since i would be using the vbox drivers provided by guest additions on VirtualBox. In this scenario how to i get OpenGL libraries on Ubuntu. (Especially i am looking for solution other than Mesa, since mesa has support only for VMware and not for VirtualBox Thank you

  Read the article

• Low Graphics and laggy screen after update to 13.10 from 13.04

  - by Wh0RU

  After updating from 13.04 to 13.10 many of 3D unity stuff has stopped working, I am suing Samsung Series 3 (NP350V5X) Laptop which has Switchable Intel and AMD Radeon HD 7670M GFX. xserver-xorg-video-ati does works but NO 3D support and graphics are very low. [I am currently using this] fglrx & fglrx-updates shows blank screen after Login. Intel Graphic Install doesn't work either (dependency error) Output of $ sudo lshw -c video *-display description: VGA compatible controller product: Thames [Radeon HD 7500M/7600M Series] vendor: Advanced Micro Devices, Inc. [AMD/ATI] physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:45 memory:e0000000-efffffff memory:c0120000-c013ffff ioport:3000(size=256) memory:c0100000-c011ffff *-display description: VGA compatible controller product: 3rd Gen Core processor Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:bfc00000-bfffffff memory:d0000000-dfffffff ioport:4000(size=64) Similarly $ /usr/lib/nux/unity_support_test -p OpenGL vendor string: VMware, Inc. OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 3.3, 256 bits) OpenGL version string: 2.1 Mesa 9.2.1 Not software rendered: no Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no Shows no 3D support. Can anyone please guide how to make things working again.

  Read the article

• Raid on ICH9R chip set

  - by user500982

  Hi Im looking at buyign this MB: http://www.supermicro.com/products/motherboard/ATOM/ICH9/X7SPE-HF-D525.cfm Im wondering though if the chipset will support the raid configuration I need. Im looking to configure the following arrays: raid array 1: 2 2TB Disks in Raid 0 raid array 2: 2 2TB Disks in Raid 0 raid array 3 (not actualy an array): 1 300GB Disk not in raid, to be used for OS and boot. So in total there would be 5 drives and the board supports 6. so im good when it comes to connections. However I have herd some chip sets only support one raid array (volume). so either all drives are individual, or are in the array. I must have 2 sperate raid arrays independent of each other, and a 5th drive not in any array. Anybody know if this setup will work? Thanks, -Stewart

  Read the article

• Cannot open root device xvda1 or unknown-block(0,0)

  - by svoop

  I'm putting together a Dom0 and three DomU (all Gentoo) with kernel 3.5.7 and Xen 4.1.1. Each Dom has it's own md (md0 for Dom0, md1 for Dom1 etc). Dom0 works fine so far, however, I'm stuck trying to create DomUs. It appears the xvda1 device on DomU is not created or accessible: Parsing config file dom1 domainbuilder: detail: xc_dom_allocate: cmdline="root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3", features="(null)" domainbuilder: detail: xc_dom_kernel_mem: called domainbuilder: detail: xc_dom_boot_xen_init: ver 4.1, caps xen-3.0-x86_64 xen-3.0-x86_32p hvm-3.0-x86_32 hvm-3.0-x86_32p hvm-3.0-x86_64 domainbuilder: detail: xc_dom_parse_image: called domainbuilder: detail: xc_dom_find_loader: trying multiboot-binary loader ... domainbuilder: detail: loader probe failed domainbuilder: detail: xc_dom_find_loader: trying Linux bzImage loader ... domainbuilder: detail: xc_dom_malloc : 10530 kB domainbuilder: detail: xc_dom_do_gunzip: unzip ok, 0x2f7a4f -> 0xa48888 domainbuilder: detail: loader probe OK xc: detail: elf_parse_binary: phdr: paddr=0x1000000 memsz=0x558000 xc: detail: elf_parse_binary: phdr: paddr=0x1558000 memsz=0x690e8 xc: detail: elf_parse_binary: phdr: paddr=0x15c2000 memsz=0x127c0 xc: detail: elf_parse_binary: phdr: paddr=0x15d5000 memsz=0x533000 xc: detail: elf_parse_binary: memory: 0x1000000 -> 0x1b08000 xc: detail: elf_xen_parse_note: GUEST_OS = "linux" xc: detail: elf_xen_parse_note: GUEST_VERSION = "2.6" xc: detail: elf_xen_parse_note: XEN_VERSION = "xen-3.0" xc: detail: elf_xen_parse_note: VIRT_BASE = 0xffffffff80000000 xc: detail: elf_xen_parse_note: ENTRY = 0xffffffff815d5210 xc: detail: elf_xen_parse_note: HYPERCALL_PAGE = 0xffffffff81001000 xc: detail: elf_xen_parse_note: FEATURES = "!writable_page_tables|pae_pgdir_above_4gb" xc: detail: elf_xen_parse_note: PAE_MODE = "yes" xc: detail: elf_xen_parse_note: LOADER = "generic" xc: detail: elf_xen_parse_note: unknown xen elf note (0xd) xc: detail: elf_xen_parse_note: SUSPEND_CANCEL = 0x1 xc: detail: elf_xen_parse_note: HV_START_LOW = 0xffff800000000000 xc: detail: elf_xen_parse_note: PADDR_OFFSET = 0x0 xc: detail: elf_xen_addr_calc_check: addresses: xc: detail: virt_base = 0xffffffff80000000 xc: detail: elf_paddr_offset = 0x0 xc: detail: virt_offset = 0xffffffff80000000 xc: detail: virt_kstart = 0xffffffff81000000 xc: detail: virt_kend = 0xffffffff81b08000 xc: detail: virt_entry = 0xffffffff815d5210 xc: detail: p2m_base = 0xffffffffffffffff domainbuilder: detail: xc_dom_parse_elf_kernel: xen-3.0-x86_64: 0xffffffff81000000 -> 0xffffffff81b08000 domainbuilder: detail: xc_dom_mem_init: mem 5000 MB, pages 0x138800 pages, 4k each domainbuilder: detail: xc_dom_mem_init: 0x138800 pages domainbuilder: detail: xc_dom_boot_mem_init: called domainbuilder: detail: x86_compat: guest xen-3.0-x86_64, address size 64 domainbuilder: detail: xc_dom_malloc : 10000 kB domainbuilder: detail: xc_dom_build_image: called domainbuilder: detail: xc_dom_alloc_segment: kernel : 0xffffffff81000000 -> 0xffffffff81b08000 (pfn 0x1000 + 0xb08 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x1000+0xb08 at 0x7fdec9b85000 xc: detail: elf_load_binary: phdr 0 at 0x0x7fdec9b85000 -> 0x0x7fdeca0dd000 xc: detail: elf_load_binary: phdr 1 at 0x0x7fdeca0dd000 -> 0x0x7fdeca1460e8 xc: detail: elf_load_binary: phdr 2 at 0x0x7fdeca147000 -> 0x0x7fdeca1597c0 xc: detail: elf_load_binary: phdr 3 at 0x0x7fdeca15a000 -> 0x0x7fdeca1cd000 domainbuilder: detail: xc_dom_alloc_segment: phys2mach : 0xffffffff81b08000 -> 0xffffffff824cc000 (pfn 0x1b08 + 0x9c4 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x1b08+0x9c4 at 0x7fdec91c1000 domainbuilder: detail: xc_dom_alloc_page : start info : 0xffffffff824cc000 (pfn 0x24cc) domainbuilder: detail: xc_dom_alloc_page : xenstore : 0xffffffff824cd000 (pfn 0x24cd) domainbuilder: detail: xc_dom_alloc_page : console : 0xffffffff824ce000 (pfn 0x24ce) domainbuilder: detail: nr_page_tables: 0x0000ffffffffffff/48: 0xffff000000000000 -> 0xffffffffffffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x0000007fffffffff/39: 0xffffff8000000000 -> 0xffffffffffffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x000000003fffffff/30: 0xffffffff80000000 -> 0xffffffffbfffffff, 1 table(s) domainbuilder: detail: nr_page_tables: 0x00000000001fffff/21: 0xffffffff80000000 -> 0xffffffff827fffff, 20 table(s) domainbuilder: detail: xc_dom_alloc_segment: page tables : 0xffffffff824cf000 -> 0xffffffff824e6000 (pfn 0x24cf + 0x17 pages) domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x24cf+0x17 at 0x7fdece676000 domainbuilder: detail: xc_dom_alloc_page : boot stack : 0xffffffff824e6000 (pfn 0x24e6) domainbuilder: detail: xc_dom_build_image : virt_alloc_end : 0xffffffff824e7000 domainbuilder: detail: xc_dom_build_image : virt_pgtab_end : 0xffffffff82800000 domainbuilder: detail: xc_dom_boot_image: called domainbuilder: detail: arch_setup_bootearly: doing nothing domainbuilder: detail: xc_dom_compat_check: supported guest type: xen-3.0-x86_64 <= matches domainbuilder: detail: xc_dom_compat_check: supported guest type: xen-3.0-x86_32p domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_32 domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_32p domainbuilder: detail: xc_dom_compat_check: supported guest type: hvm-3.0-x86_64 domainbuilder: detail: xc_dom_update_guest_p2m: dst 64bit, pages 0x138800 domainbuilder: detail: clear_page: pfn 0x24ce, mfn 0x37ddee domainbuilder: detail: clear_page: pfn 0x24cd, mfn 0x37ddef domainbuilder: detail: xc_dom_pfn_to_ptr: domU mapping: pfn 0x24cc+0x1 at 0x7fdece675000 domainbuilder: detail: start_info_x86_64: called domainbuilder: detail: setup_hypercall_page: vaddr=0xffffffff81001000 pfn=0x1001 domainbuilder: detail: domain builder memory footprint domainbuilder: detail: allocated domainbuilder: detail: malloc : 20658 kB domainbuilder: detail: anon mmap : 0 bytes domainbuilder: detail: mapped domainbuilder: detail: file mmap : 0 bytes domainbuilder: detail: domU mmap : 21392 kB domainbuilder: detail: arch_setup_bootlate: shared_info: pfn 0x0, mfn 0xbaa6f domainbuilder: detail: shared_info_x86_64: called domainbuilder: detail: vcpu_x86_64: called domainbuilder: detail: vcpu_x86_64: cr3: pfn 0x24cf mfn 0x37dded domainbuilder: detail: launch_vm: called, ctxt=0x7fff224e4ea0 domainbuilder: detail: xc_dom_release: called Daemon running with PID 4639 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.5.7-gentoo (root@majordomo) (gcc version 4.5.4 (Gentoo 4.5.4 p1.0, pie-0.4.7) ) #1 SMP Tue Nov 20 10:49:51 CET 2012 [ 0.000000] Command line: root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3 [ 0.000000] ACPI in unprivileged domain disabled [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] Xen: [mem 0x0000000000000000-0x000000000009ffff] usable [ 0.000000] Xen: [mem 0x00000000000a0000-0x00000000000fffff] reserved [ 0.000000] Xen: [mem 0x0000000000100000-0x0000000138ffffff] usable [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] MPS support code is not built-in. [ 0.000000] Using acpi=off or acpi=noirq or pci=noacpi may have problem [ 0.000000] DMI not present or invalid. [ 0.000000] No AGP bridge found [ 0.000000] e820: last_pfn = 0x139000 max_arch_pfn = 0x400000000 [ 0.000000] e820: last_pfn = 0x100000 max_arch_pfn = 0x400000000 [ 0.000000] init_memory_mapping: [mem 0x00000000-0xffffffff] [ 0.000000] init_memory_mapping: [mem 0x100000000-0x138ffffff] [ 0.000000] NUMA turned off [ 0.000000] Faking a node at [mem 0x0000000000000000-0x0000000138ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x138ffffff] [ 0.000000] NODE_DATA [mem 0x1387fc000-0x1387fffff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00010000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal [mem 0x100000000-0x138ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00010000-0x0009ffff] [ 0.000000] node 0: [mem 0x00100000-0x138ffffff] [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] No local APIC present [ 0.000000] APIC: disable apic facility [ 0.000000] APIC: switched to apic NOOP [ 0.000000] e820: cannot find a gap in the 32bit address range [ 0.000000] e820: PCI devices with unassigned 32bit BARs may break! [ 0.000000] e820: [mem 0x139100000-0x1394fffff] available for PCI devices [ 0.000000] Booting paravirtualized kernel on Xen [ 0.000000] Xen version: 4.1.1 (preserve-AD) [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:1 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 26 pages/cpu @ffff880138400000 s75712 r8192 d22592 u2097152 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1259871 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: root=/dev/xvda1 console=hvc0 root=/dev/xvda1 ro 3 [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Memory: 4943980k/5128192k available (3937k kernel code, 448k absent, 183764k reserved, 1951k data, 524k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:4352 nr_irqs:256 16 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] console [hvc0] enabled [ 0.000000] installing Xen timer for CPU 0 [ 0.000000] Detected 3411.602 MHz processor. [ 0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 6823.20 BogoMIPS (lpj=3411602) [ 0.000999] pid_max: default: 32768 minimum: 301 [ 0.000999] Security Framework initialized [ 0.001355] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) [ 0.002974] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.003441] Mount-cache hash table entries: 256 [ 0.003595] Initializing cgroup subsys cpuacct [ 0.003599] Initializing cgroup subsys freezer [ 0.003637] ENERGY_PERF_BIAS: Set to 'normal', was 'performance' [ 0.003637] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8) [ 0.003643] CPU: Physical Processor ID: 0 [ 0.003645] CPU: Processor Core ID: 0 [ 0.003702] SMP alternatives: switching to UP code [ 0.011791] Freeing SMP alternatives: 12k freed [ 0.011835] Performance Events: unsupported p6 CPU model 42 no PMU driver, software events only. [ 0.011886] Brought up 1 CPUs [ 0.011998] Grant tables using version 2 layout. [ 0.012009] Grant table initialized [ 0.012034] NET: Registered protocol family 16 [ 0.012328] PCI: setting up Xen PCI frontend stub [ 0.015089] bio: create slab <bio-0> at 0 [ 0.015158] ACPI: Interpreter disabled. [ 0.015180] xen/balloon: Initialising balloon driver. [ 0.015180] xen-balloon: Initialising balloon driver. [ 0.015180] vgaarb: loaded [ 0.016126] SCSI subsystem initialized [ 0.016314] PCI: System does not support PCI [ 0.016320] PCI: System does not support PCI [ 0.016435] NetLabel: Initializing [ 0.016438] NetLabel: domain hash size = 128 [ 0.016440] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.016447] NetLabel: unlabeled traffic allowed by default [ 0.016475] Switching to clocksource xen [ 0.017434] pnp: PnP ACPI: disabled [ 0.017501] NET: Registered protocol family 2 [ 0.017864] IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 0.019322] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [ 0.020376] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.020497] TCP: Hash tables configured (established 524288 bind 65536) [ 0.020500] TCP: reno registered [ 0.020525] UDP hash table entries: 4096 (order: 5, 131072 bytes) [ 0.020564] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes) [ 0.020624] NET: Registered protocol family 1 [ 0.020658] PCI-DMA: Using software bounce buffering for IO (SWIOTLB) [ 0.020662] software IO TLB [mem 0xfb632000-0xff631fff] (64MB) mapped at [ffff8800fb632000-ffff8800ff631fff] [ 0.020750] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 0.021378] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.023378] msgmni has been set to 9656 [ 0.023544] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.023549] io scheduler noop registered [ 0.023551] io scheduler deadline registered [ 0.023580] io scheduler cfq registered (default) [ 0.023650] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.023845] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.024082] Non-volatile memory driver v1.3 [ 0.024085] Linux agpgart interface v0.103 [ 0.024207] Event-channel device installed. [ 0.024265] [drm] Initialized drm 1.1.0 20060810 [ 0.024268] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 0.025145] brd: module loaded [ 0.025565] loop: module loaded [ 0.045646] Initialising Xen virtual ethernet driver. [ 0.198264] i8042: PNP: No PS/2 controller found. Probing ports directly. [ 0.199096] i8042: No controller found [ 0.199139] mousedev: PS/2 mouse device common for all mice [ 0.259303] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 [ 0.259353] rtc_cmos: probe of rtc_cmos failed with error -38 [ 0.259440] md: raid1 personality registered for level 1 [ 0.259542] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 0.259732] ip_tables: (C) 2000-2006 Netfilter Core Team [ 0.259747] TCP: cubic registered [ 0.259886] NET: Registered protocol family 10 [ 0.260031] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 0.260070] sit: IPv6 over IPv4 tunneling driver [ 0.260194] NET: Registered protocol family 17 [ 0.260213] Bridge firewalling registered [ 5.360075] XENBUS: Waiting for devices to initialise: 25s...20s...15s...10s...5s...0s...235s...230s...225s...220s...215s...210s...205s...200s...195s...190s...185s...180s...175s...170s...165s...160s...155s...150s...145s...140s...135s...130s...125s...120s...115s...110s...105s...100s...95s...90s...85s...80s...75s...70s...65s...60s...55s...50s...45s...40s...35s...30s...25s...20s...15s...10s...5s...0s... [ 270.360180] XENBUS: Timeout connecting to device: device/vbd/51713 (local state 3, remote state 1) [ 270.360273] md: Waiting for all devices to be available before autodetect [ 270.360277] md: If you don't use raid, use raid=noautodetect [ 270.360388] md: Autodetecting RAID arrays. [ 270.360392] md: Scanned 0 and added 0 devices. [ 270.360394] md: autorun ... [ 270.360395] md: ... autorun DONE. [ 270.360431] VFS: Cannot open root device "xvda1" or unknown-block(0,0): error -6 [ 270.360435] Please append a correct "root=" boot option; here are the available partitions: [ 270.360440] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 270.360444] Pid: 1, comm: swapper/0 Not tainted 3.5.7-gentoo #1 [ 270.360446] Call Trace: [ 270.360454] [<ffffffff813d2205>] ? panic+0xbe/0x1c5 [ 270.360459] [<ffffffff813d2358>] ? printk+0x4c/0x51 [ 270.360464] [<ffffffff815d5fb7>] ? mount_block_root+0x24f/0x26d [ 270.360469] [<ffffffff815d62b6>] ? prepare_namespace+0x168/0x192 [ 270.360474] [<ffffffff815d5ca7>] ? kernel_init+0x1b0/0x1c2 [ 270.360477] [<ffffffff815d5500>] ? loglevel+0x34/0x34 [ 270.360482] [<ffffffff813d5a64>] ? kernel_thread_helper+0x4/0x10 [ 270.360486] [<ffffffff813d4038>] ? retint_restore_args+0x5/0x6 [ 270.360490] [<ffffffff813d5a60>] ? gs_change+0x13/0x13 The config: name = "dom1" bootloader = "/usr/bin/pygrub" root = "/dev/xvda1 ro" extra = "3" # runlevel memory = 5000 disk = [ 'phy:/dev/md1,xvda1,w' ] # vif = [ 'ip=..., vifname=veth1' ] # none for now Here are some details on the Dom0 kernel (grepping for "xen"): CONFIG_XEN=y CONFIG_XEN_DOM0=y CONFIG_XEN_PRIVILEGED_GUEST=y CONFIG_XEN_PVHVM=y CONFIG_XEN_MAX_DOMAIN_MEMORY=500 CONFIG_XEN_SAVE_RESTORE=y CONFIG_PCI_XEN=y CONFIG_XEN_PCIDEV_FRONTEND=y # CONFIG_XEN_BLKDEV_FRONTEND is not set CONFIG_XEN_BLKDEV_BACKEND=y # CONFIG_XEN_NETDEV_FRONTEND is not set CONFIG_XEN_NETDEV_BACKEND=y CONFIG_INPUT_XEN_KBDDEV_FRONTEND=y CONFIG_HVC_XEN=y CONFIG_HVC_XEN_FRONTEND=y # CONFIG_XEN_WDT is not set # CONFIG_XEN_FBDEV_FRONTEND is not set # Xen driver support CONFIG_XEN_BALLOON=y # CONFIG_XEN_SELFBALLOONING is not set CONFIG_XEN_SCRUB_PAGES=y CONFIG_XEN_DEV_EVTCHN=y CONFIG_XEN_BACKEND=y CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_SYS_HYPERVISOR=y CONFIG_XEN_XENBUS_FRONTEND=y CONFIG_XEN_GNTDEV=m CONFIG_XEN_GRANT_DEV_ALLOC=m CONFIG_SWIOTLB_XEN=y CONFIG_XEN_TMEM=y CONFIG_XEN_PCIDEV_BACKEND=m CONFIG_XEN_PRIVCMD=y CONFIG_XEN_ACPI_PROCESSOR=m And the DomU kernel (grepping for "xen"): CONFIG_XEN=y CONFIG_XEN_DOM0=y CONFIG_XEN_PRIVILEGED_GUEST=y CONFIG_XEN_PVHVM=y CONFIG_XEN_MAX_DOMAIN_MEMORY=500 CONFIG_XEN_SAVE_RESTORE=y CONFIG_PCI_XEN=y CONFIG_XEN_PCIDEV_FRONTEND=y CONFIG_XEN_BLKDEV_FRONTEND=y CONFIG_XEN_NETDEV_FRONTEND=y CONFIG_INPUT_XEN_KBDDEV_FRONTEND=y CONFIG_HVC_XEN=y CONFIG_HVC_XEN_FRONTEND=y # CONFIG_XEN_WDT is not set # CONFIG_XEN_FBDEV_FRONTEND is not set # Xen driver support CONFIG_XEN_BALLOON=y # CONFIG_XEN_SELFBALLOONING is not set CONFIG_XEN_SCRUB_PAGES=y CONFIG_XEN_DEV_EVTCHN=y # CONFIG_XEN_BACKEND is not set CONFIG_XENFS=y CONFIG_XEN_COMPAT_XENFS=y CONFIG_XEN_SYS_HYPERVISOR=y CONFIG_XEN_XENBUS_FRONTEND=y CONFIG_XEN_GNTDEV=m CONFIG_XEN_GRANT_DEV_ALLOC=m CONFIG_SWIOTLB_XEN=y CONFIG_XEN_TMEM=y CONFIG_XEN_PRIVCMD=y CONFIG_XEN_ACPI_PROCESSOR=m Any ideas what I'm doing wrong here? Thanks a lot!

  Read the article

• Picking Core Language For Large Scale Web Platform

  - by ryanzec

  Now I have work with PHP and ASP.NET quite a bit and also played around few other language for web development. I am now at a point where need to start building a backend platform that will have the ability to support a large set of applications and I am trying to figure out which language I want to choose as my core language. When I say core language I mean the language that the majority of the backend code is going to be in. This is not to say that other languages won't be used because my guess is that they will but I want a large majority of the code (90%-98%) to be in 1 language. While I see to benefit of using the language that is best for the job, having 15% in php, 15% in ASP.NET, 5% in perl, 10% in python, 15% in ruby, etc… seems like a very bad idea to me (not to mention integrating everything seamlessly would probably add a bit of overhead). If you were going to be building a large scale web platform that need to support multiple applications from scratch, what would you choose as your core language and why?

  Read the article

• Most suited technology for browser games?

  - by Tingle

  I was thinking about making a 2D MMO which I would in the long run support on various plattforms like desktop, mac, browser, android and ios. The server will be c++/linux based and the first client would go in the browser. So I have done some research and found that webgl and flash 11 support hardware accelerated rendering, I saw some other things like normal HTML5 painting. So my question is, which technology should I use for such a project? My main goal would be that the users have a hassle free experience using what there hardware can give them with hardware acceleration. And the client should work on the most basic out-of-the-box pc's that any casual pc or mac user has. And another criteria would be that it should be developer friendly. I've messed with webgl abit for example and that would require writing a engine from scratch - which is acceptable but not preferred. Also, in case of non-actionscript, which kind language is most prefered in terms of speed and flexability. I'm not to fond of javascript due to the garbage collector but have learned to work around it. Thank you for you time.

  Read the article

• Sandcastle Help File Builder - October 2010 release

  - by TATWORTH

  At http://shfb.codeplex.com/releases/view/92191, the latest Sandcastle has been released. I am pleased to say that it incorporates the generic version of a fix, I originated that allows projects including Crystal Reports to be documented.Here is the relevant passage from the help file:"The default configuration for MRefBuilder has been updated to ignore the Crystal Reports licensing assembly (BusinessObjects.Licensing.KeycodeDecoder) if it fails to get resolved. This assembly does not appear to be available and ignoring it prevents projects that include Crystal Reports assemblies from failing and being unbuildable."There are many other fixes. Here are the release notes:IMPORTANT: On some systems, the content of the ZIP file is blocked and the installer may fail to run. Before extracting it, right click on the ZIP file, select Properties, and click on the Unblock button if it is present in the lower right corner of the General tab in the properties dialog.This release supports the Sandcastle October 2012 Release (v2.7.1.0). It includes full support for generating, installing, and removing MS Help Viewer files. This new release supports Visual Studio 2010 and 2012 solutions and projects as documentation sources, and adds support for projects targeting the .NET 4.5 Framework, .NET Portable Library 4.5, and .NET for Windows Store Apps.See the Sandcastle 2.7.1.0 Release Notes for details on all of the changes made to the underlying Sandcastle tools and presentation styles.This release uses the Sandcastle Guided Installation package. Download and extract to a folder and then runSandcastleInstaller.exe to run the guided installation of Sandcastle, the various extra items, the Sandcastle Help File Builder core components, and the Visual Studio extension package.What's IncludedHelp 1 compiler check and instructions on where to download it and how to install it if neededHelp 2 compiler check and instructions on where to download it and how to install it if neededSandcastle October 2012 2.7.1.0An option to install the MAML schemas in Visual Studio to provide IntelliSense for MAML topicsSandcastle Help File Builder 1.9.5.0SHFB Visual Studio Extension PackageFor more information about the Visual Studio extension package, see the Visual Studio Package help file topic.

  Read the article

• Go back to 32-bit Java in OS X so I can use Chrome

  - by Mac Kris

  Recently Apple released a Java update. I mindlessly downloaded and installed it, thinking it must be good (I know that was stupid on my part). Now chrome doesn't work where sites require Java support. In terminal, java -version shows I have the 64bit version installed. I know Chrome does not support 64bit Java. I'd like to go back to the last version that worked for me, the 32-bit version. I don't want to use Safari or Firefox. I'd like Chrome to work. I have too much invested in customizing it to work with another browser.

  Read the article

• Virtualization in Ubuntu 11.10

  - by Mascarpone

  Since Ubuntu 11.10 use a new kernel, it's very difficult to have a decent support for virtualization. VirtualBox doesn't support guest additions for ubuntu 11.10, so I can't copy to and from my ubuntu desktop and windows, which I absolutely require, plus FreeBSD seems not to be able to use DHCP without guest additions. Virt-manager instead gives an error on launch: Unable to open a connection to the libvirt management daemon. Libvirt URI is: qemu:///system Verify that: - The 'libvirt-bin' package is installed - The 'libvirtd' daemon has been started - You are member of the 'libvirtd' group unable to connect to '/var/run/libvirt/libvirt-sock', libvirtd may need to be started: Permission denied Traceback (most recent call last): File "/usr/share/virt-manager/virtManager/connection.py", line 1146, in _open_thread self.vmm = self._try_open() File "/usr/share/virt-manager/virtManager/connection.py", line 1130, in _try_open flags) File "/usr/lib/python2.7/dist-packages/libvirt.py", line 102, in openAuth if ret is None:raise libvirtError('virConnectOpenAuth() failed') libvirtError: unable to connect to '/var/run/libvirt/libvirt-sock', libvirtd may need to be started: Permission denied The problem is solved by running virt-manager as root, but I don't like that. How do I change permissions to run Virt-Manager as user? Is there a way to install guest additions on Ubuntu 11.10?

  Read the article

• What are the challenges of implementing an ERP system?

  When a company decides to rollout an ERP system as part of its core business processes they must consider and provide solutions for the following general challenges. It is important to note that this list is generic and that every ERP system that rolls out is as distinct as the companies that are trying to implement the system. Upper Management Support Reengineering Existing Business Process and Applications Integration of the ERP with other existing departmental applications Implementation Time Implementation Costs Employee Training I just recently read an article by Mano Billi called “What are the major challenges in implementing ERP? “ were he basically outlines the common challenges to implementing an ERP system within a company. He discusses items like Upper management support, altering existing systems, and how ERPs integrate with other independent systems. In addition, he also covers items on selecting a ERP vendor, ERP Consultants, and the effects of an ERP system on employees.  I personally think he did a create job of outlining common issues that can cause an ERP implementation to fail or not be as effective as it potentially could be if the challenges are not taken in to account appropriately.

  Read the article

• How to choose a server side language / framework

  - by pllee

  I am trying to come up with a list / ranking system on determining which server language to choose for a particular website. Assume that familiarity with a certain language is not important and the implementation can be done in any language. Here are some things that might be important but I am not sure how to rank them : Maintainability. Libraries. For example, Memcached and NoSql support right out the box would be really nice addition to a particular framework. 3rd party SDK's. For example, if I need Paypal on my site they openly provide SDK's for all senarios in Java, PHP and .Net. If I choose Django I would have to rely on 3rd party libraries that are don't support everything and are not officially maintained. Would that be dealbreaker for Django? Performance This one is tricky to put on a generic list because it can be a deal breaker but for many websites performance will not be an issue that the language/framework is responsible for. Cost (hosting, open source). edit - Any reason for the votes to close? I didn't see any duplicates mentioned and the question should not drum up a flame war.

  Read the article

• DHCPPloc.exe or equivalent for Windows 7?

  - by Bart B

  There seems to be some DHCP funnyness going on so I need to run something to show me what's going at a DHCP level. Before I upgraded my machine to Windows 7 I used DHCPloc.exe from the Windows XP support tools, and it worked like a charm. I can't seem to find Support Tools for Windows 7, and trying to use the XP tools in compatibility mode doesn't work (I tried, it fails to open a receiving socket). I need a tool to monitor DHCP traffic, and ideally one that lets me filter it to exclude DHCP traffic from our trusted DHCP servers and only show me un-authorised DHCP traffic.

  Read the article

• ERP/CRM Systems. Desktop Based ? Web based? [closed]

  - by Parhs

  I have seen 2-3 ERPs in action. I am wondering what is better. Desktop based application or webbased displayed on a browser. My first experience was with a web based ERP when i was 14 years old.. It was web based and terribly slow... For most simple task you had to do lots of clicks... no keyboard support ..... Pages took ages to load. Last year I worked for migrating to a newer computer some old terminal based cobol application. The computer that worked till today and still has no problem was from 1993. The user interface ofcourse was textbased.. The speed that guys placed orders was amazing! just typing the name of the customer , then 5-10 keys to add a product to order.... Comparing to this ERP the page for placing orders Link (click sales orders) seems terribly slow to add a product... No keyboard shortcut works to save what you added and generally I believe you need 4 times more time to place an order compared to the text interface... Having to use both mouse and keyboard for this task is BAD and sadistic... So how can the heck these people ever use a system like that ??? So in the long run desktop application seems the only way... Of course browsers support shortcuts but the way to overide the defaults that browsers uses isn't cross compatible... That is a huge problem. Finnaly, if we MUST/forced use cloud in near future what about keyboard shortcuts?? I feel confused... I have seen converters of desktop applications to browser applications but are SLOW as hell... The question is what about user friendliness? What kind of application would you use?

  Read the article

• Fusion CRM Release 7 RCDs and TOIs Now Available!

  - by Richard Lefebvre

  Fusion CRM Release 7 Release Content Documents (RCD) and Transfer of Information (TOI) presentations are now available. In addition, you can find 245 new or changed product features for Release 7 on Oracle Product Features. All the new RCDs and TOIs can be found on the Fusion Learning Center: Customer Relationship Management TOIs - Customer Center, Define Segmentation Strategy, Enterprise Contracts, Oracle Social Network, Sales, and Territory Management Business Process Model (BPM) RCDs - Customer Service, Marketing, Order Fulfillment, and Sales Financials BPM RCDs - Asset Lifecycle Management, Cash and Treasury Management, and Financial Control and Reporting Human Capital Management TOIs - Workforce Development, Compensation, Benefits, Worker Performance, Workforce Profiles, Enterprise Structures, Talent Review, Manage Transaction and Batch Processing, Delete HCM Storage Data, and Load Batch Data BPM RCDs - Compensation Management, Enterprise Information Management, Workforce Deployment, and Workforce Development Procurement TOI - Requisitions BPM RCD - Procurement Project Portfolio Management TOIs - Project Resources, Evaluate and Assign Resources, Maintain Resource Assignments, Manage Resource Demand, Manage Resource Supply, Manage Resource Utilization and Analytics, Project Management, Set Up Project Management BPM RCD - Project Management Supply Chain Management TOIs - Manage New Product Definition and Approval, Manage Product Change Orders, Product Hub, Define Item Class BPM RCDs - Materials Management and Logistics, Product Management and Supply Chain Planning Partners and customers can access the content from the following locations: Partner access: BPM RCDs and TOIs Oracle Partner Network Fusion Learning Center New Feature RCDs Oracle Product Features Customer access: TOIs My Oracle Support (Note:1528594.1) BPM RCDs My Oracle Support (Note:1559828.1) New Feature RCDs Oracle Product Features

  Read the article

• how to start with unmanaged vps?

  - by GaVrA

  Hello! I have a managed VPS, so whatever i need i can just ask my support, and they will do it for me. Now i plan to migrate to unmanaged VPS, so i need some guides, tips on how and where to start learning. I will have more specific questions once i start using it, but now i just need some general answers about this topic. Thanks. Update: Ok, i have decided to go for unmanaged VPS with cPanel. OS is CentOS-5. I contacted support only for some small(i think) things like creating new account in whm, some database importing, installing new software(rare)... What i will be using is apache, php, mysql. I think i will be able to cope with upgrading to new versions, so the thing that interests me the most is security i guess.

  Read the article

• Is WEP used in conjunction with a wireless access list adequate security?

  - by LeopardSkinPillBoxHat

  I use a Netgear wireless router, with various wireless devices connecting to it. One of my wireless devices doesn't support WPA2 security, so I had to downgrade the security on the router to WEP. We all know WEP is broken, so as an added measure I enabled a wireless access list on the router so that only devices with specified MAC addresses which are in my access list are permitted to connect to the router. I know it is possible to spoof a MAC address from a device for the purposes of accessing a secure network like this. But is it easy? Is using WEP and a wireless access list good enough to prevent most hacking attacks? Or should I do whatever I can to ensure all devices support WPA2 in the future?

  Read the article

• Jumbo Frames on DIR-655

  - by Spookyone

  Hello, I am trying to set up jumbo frames on my gigabit home LAN but no luck so far. My setup is: D-Link DIR-655 router, HW Revision A3, Firmware 1.21 EU Synology DS107+, Firmware 3.0-1337 Laptop w/ Win7 x64, external PCIx NIC managed by "Generic Marvel Yukon 88E8053 based Ethernet Controller" The router is supposed to support jumbo frames but doesn't feature any relevant setting. I set the Jumbo Packet value to 9000 on both the NIC and the Synobox but it doesn't work, ping -f -l 8972 says "Packet needs to be fragmented but DF set". Is there any other setting I overlooked, the DIR-655 doesn't actually support jumbo frames, or what else could be the problem?

  Read the article

< Previous Page | 185 186 187 188 189 190 191 192 193 194 195 196  | Next Page >