Search Results

Search found 44742 results on 1790 pages for 'create'.

Page 190/1790 | < Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >

• How can I create a simple Exchange 2010 backup solution?

  - by bduncanj

  I'm sure this question's been asked a dozen times in one form or another, however after much searching, there doesn't appear to be an obvious simple recovery solution for a single Exchange box. We're using Exchange 2010 on a single server, the server hosts the AD and nothing else on the network uses the AD. The intent is to run this server as you would an externally hosted Exchange server - access only via HTTP (RPC mode or OWA) - all other ports blocked. I've a daily backup running, using Windows Server 2008 volume shadow service to backup the Exchange data to an external hard disk. My question is, how do I perform a bare metal recovery of this server? 1) Do I need to be explicitly including the active directory information in this nightly backup, or will it be there by virtue of the fact that this system is the primary AD server and the Windows backup service knows this? 2) I understand I can re-install Server 2008 onto my new hardware (in the case of hardware failure) and then run Exchange 2010 setup.exe with a /recover argument, referencing the backup volume. 3) It is acceptable to have some downtime during this recovery process. But is there anything else I should be aware of? Thanks! Duncan

  Read the article

• Can I create a virtual network interface to connect to a real network device?

  - by michelemarcon

  I have a networked windows pc with 2 network interfaces. The first connects to a lan with ip address 10.1.. The second connects to another lan with ip address 10.2.. Maybe it's a dumb question, however is it possible to virtualize the second network interface, so that the pc can connect to the 2 lans? If necessary, I may switch to linux or paravirtualization. CLARIFICATION: I want to send DHCP broadcast packets on the second lan, but not on the first lan. I want to do it with one single physical network interface. At the moment, I'm not using any virtualization software.

  Read the article

• I need to know how to create a custom webform template in ASP.NET that allows me to pick a master pa

  - by Pete

  Using Visual Studio 2008, I need to create a custom web form that when picked acts like the web content form, by providing a dialog that lets you pick a master page. I have looked through the webform.zip template and thought I had a clue, but trying different combinations has baffled me as it either doesn't appear or doesn't work. Also when you set the project type to Web and sub project type to CSharp it doesn't appear, so I don't know if this part of the cause, because I would of hoped that the SupportsMasterPage element would of caused this dialog to appear, if it is a web item, but no luck. Frown Any ideas? p.s. I have used my googling resources to the maximum so unsure what to do.

  Read the article

• When HDD becomes full, how to create a symbolic link to the data store on another disk?

  - by Brij Raj Singh

  I have a Linux Ubuntu machine which has an X GB hard disk. There is folder, say, /opt/software/data. The disk /dev/sda1 is almost full and I have attached another disk at /dev/sda2 which is mounted at /hdd2. Is it possible for me to link the folders /opt/software/data with /hdd2/software/data so, that every file get stored in the /hdd2/software/data but may be referred from the /opt/software/data? I can't do a reinstall of the software that creates this data, to change the default location of storage.

  Read the article

• Workflow Foundation: How to create Recieve activity with custom message in xaml designer?

  - by Petr Felzmann

  I need to have Recieve activity which can receive my custom data. I found examples, but all use coded workflows like such public class ProcessRequest : Activity { public ProcessRequest() { Variable<MyData> request = new Variable<MyData> { Name = "request" }; Receive receiveRequest = new Receive { ServiceContractName = "IProcessRequest", OperationName = "Foo", CanCreateInstance = true, Content = ReceiveContent.Create(new OutArgument<MyData>(request)) }; } } The main point is that Recieve.Content property. It is not clear for me how I can do it in XAML designer. What I have to set in the dialog of the Content property - Message or Parameters and what to set inside those options? Thanks for the light!

  Read the article

• How do you create a Google Maps-esque drop down dialog?

  - by Daniel Lew

  In the Google Maps application, when you open the menu and click on "Directions", it pops up a dialog that is unique to Google Maps. It keeps the MapView in the background, but displays the search dialog from the top (or bottom, if you're on an old version of Android). I was curious if anyone knew how they achieved this effect. I'm willing to create a custom Dialog, but it seems that Dialogs are designed to pop into the middle of the screen (any other types of dialogs are denied permission as system dialogs). What trick is Google Maps using?

  Read the article

• How to create an attached-property to change a resource's property?

  - by king.net

  I have a DrawingBrush as a resource like this: <DrawingBrush x:Key="Calendar" Stretch="Uniform"> <DrawingBrush.Drawing> <DrawingGroup> <DrawingGroup.Children> <GeometryDrawing Geometry="F1 M 28.0917,2.13333C 42.4005,2.13333 54,13.7329 54,28.0417C 54,42.3504 42.4004,53.95 28.0917,53.95C 13.7829,53.95 2.18334,42.3504 2.18334,28.0417C 2.18334,13.7329 13.7829,2.13333 28.0917,2.13333 Z "> <GeometryDrawing.Pen> <Pen Thickness="4" LineJoin="Round" Brush="#FF000000"/> </GeometryDrawing.Pen> </GeometryDrawing> <GeometryDrawing Geometry="F1 M 16.9667,16.7083L 39.7167,16.7083L 39.7167,41.625L 16.9667,41.625L 16.9667,16.7083 Z "> <GeometryDrawing.Pen> <Pen Thickness="2.66667" StartLineCap="Square" EndLineCap="Square" MiterLimit="2.75" Brush="#FF000000"/> </GeometryDrawing.Pen> </GeometryDrawing> <GeometryDrawing Brush="#FF000000" Geometry="F1 M 15.6333,15.9583L 40.7167,15.9583L 40.7167,25.2917L 15.6333,25.2917L 15.6333,15.9583 Z "/> <GeometryDrawing Brush="#FFFFFFFF" Geometry="F1 M 18.2167,11.9583L 22.9667,11.9583L 22.9667,20.875L 18.2167,20.875L 18.2167,11.9583 Z "> <GeometryDrawing.Pen> <Pen Thickness="1.33333" StartLineCap="Square" EndLineCap="Square" MiterLimit="2.75" Brush="#FF000000"/> </GeometryDrawing.Pen> </GeometryDrawing> <GeometryDrawing Brush="#FFFFFFFF" Geometry="F1 M 33.7167,11.925L 38.4667,11.925L 38.4667,20.8417L 33.7167,20.8417L 33.7167,11.925 Z "> <GeometryDrawing.Pen> <Pen Thickness="1.33333" StartLineCap="Square" EndLineCap="Square" MiterLimit="2.75" Brush="#FF000000"/> </GeometryDrawing.Pen> </GeometryDrawing> <GeometryDrawing Brush="#FF000000" Geometry="F1 M 28.0154,36.2658L 28.0154,37.4894L 21.6254,37.4894C 21.6169,37.1934 21.6615,36.908 21.7592,36.6333C 21.915,36.1815 22.165,35.7425 22.5091,35.3162C 22.8533,34.8899 23.3617,34.4091 24.0344,33.8738C 25.0782,32.983 25.776,32.295 26.1279,31.81C 26.4799,31.3249 26.6558,30.8551 26.6558,30.4005C 26.6558,29.9473 26.4894,29.5653 26.1566,29.2544C 25.8238,28.9435 25.3904,28.7881 24.8565,28.7881C 24.2915,28.7881 23.8393,28.9442 23.5001,29.2565C 23.161,29.5688 22.9892,30.0018 22.985,30.5556L 21.7614,30.4196C 21.8449,29.5345 22.1576,28.86 22.6993,28.3962C 23.241,27.9323 23.9686,27.7004 24.882,27.7004C 25.8054,27.7004 26.5358,27.9596 27.0733,28.4779C 27.6107,28.9963 27.8795,29.6385 27.8795,30.4047C 27.8795,30.7942 27.8065,31.1769 27.6607,31.5529C 27.5148,31.9289 27.2726,32.3251 26.9341,32.7415C 26.5957,33.1579 26.0115,33.7215 25.1816,34.4325C 24.4692,35.0216 24.0008,35.4214 23.7763,35.6317C 23.5518,35.842 23.3667,36.0533 23.2208,36.2658L 28.0154,36.2658 Z "/> <GeometryDrawing Brush="#FF000000" Geometry="F1 M 33.3178,37.4894L 33.3178,35.1781L 28.9671,35.1781L 28.9671,33.9545L 33.5897,27.8364L 34.5414,27.8364L 34.5414,33.9545L 35.765,33.9545L 35.765,35.1781L 34.5414,35.1781L 34.5414,37.4894L 33.3178,37.4894 Z M 33.3178,33.9545L 33.3178,30.1774L 30.4648,33.9545L 33.3178,33.9545 Z "/> </DrawingGroup.Children> </DrawingGroup> </DrawingBrush.Drawing> </DrawingBrush> And I can use it like this: <Rectangle Fill="{DynamicResource Calender}" /> Now, my question is: how can I create an attached-property to change all brushes on my resource? e.g. I be able to create this: <Rectangle Fill="{DynamicResource Calendar}" attached:IconHelper.Foreground="Blue" /> on my Rectangle and in my resource, I can get: <DrawingBrush x:Key="Calendar" Stretch="Uniform"> <DrawingBrush.Drawing> <DrawingGroup> <DrawingGroup.Children> <GeometryDrawing Geometry="blah blah"> <GeometryDrawing.Pen> <Pen Brush={attached:ReadItFromAboveRectangle}/> </GeometryDrawing.Pen> </GeometryDrawing> <GeometryDrawing Geometry="blah blah"> <GeometryDrawing.Pen> <Pen Brush={attached:ReadItFromAboveRectangle}/> </GeometryDrawing.Pen> <!-- etc... --> Is there any way to read an attached-property on Rectangle in Calendar resource? Or is there any other way to do this? Thanks in advance.

  Read the article

• How do I read from a file consists of city names and coordinates/Populations and create functions to get the coordinates and population?

  - by Braybray

  I'm using Python, and I have a file which has city names and information such as names, coordinates of the city and population of the city: Youngstown, OH[4110,8065]115436 Yankton, SD[4288,9739]12011 966 Yakima, WA[4660,12051]49826 1513 2410 Worcester, MA[4227,7180]161799 2964 1520 604 Wisconsin Dells, WI[4363,8977]2521 1149 1817 481 595 How can I create a function to take the city name and return a list containing the latitude and longitude of the given city? fin = open ("miles.dat","r") def getCoordinates cities = [] for line in fin: cities.append(line.rstrip()) for word in line: print line.split() That's what I tried now; how could I get the coordinates of the city by calling the names of the city and how can I return the word of each line but not letters? Any help will be much appreciated, thanks all.

  Read the article

• Is it possible to create an efficient UDF alternative to Excel's CUBEVALUE function?

  - by bright

  We'd like to create a simpler alternative to Excel's CUBEVALUE function for retrieving data from an OLAP server. The details aren't critical, but briefly, our function will "know" the source connection and accept a very simple ticker-like parameter and a date, in place of CUBEVALUE's MDX-style parameters. This is for internal use within our firm, just FYI. However, Excel has optimized CUBEVALUE so that calls to the OLAP server are batched. Question: Is there a way to code the new function so that it can similarly batch calls rather than issue a separate query for each cell?

  Read the article

• Can Windows Media Player create playlists based on folder structure?

  - by Chaulky

  Over the years I've carefully molded my digital media collection into a series of folders that make it easy for me to find what I'm looking for. I recently discovered the awesomeness that is streaming video from Windows 7 Media Player to the PS3 so I can watch it on the big screen without all the hassle of hooking the computer up to the TV. The problem is, I totally lose my carefully crafted folder structure and all my videos become one giant mess again... not cool! As a temporary solution, I've created a few playlists for my favorites (Dexter Season 4, Dexter Season 5, Breaking Bad Season 1, etc.). This is a HUGE pain in the a$$. So, is there a way to get Windows Media Player (on Windows 7) to maintain some sort of folder structure based on the location of the actual video files? So if I have my videos sorted into folders by show and season, Media Player will pick that up and let me browse it in the same way. As an alternative answer, I'll accept suggestions for a program that can also stream to PS3 and has this "folder organization" feature.

  Read the article

• Create and manage child name servers (glue records) within my domain?

  - by basilmir

  Preface I use a top level domain provider that only allows me to add "normal" third-party name servers (a list where i can add "ns1.hostingcompany.com" type entries... nothing else) AND "child name servers" which i can later attach to my parent account ( ns1.myowndomain.com and an ip address). They do not provide other means of linking up. I want to host my own server and dns, even with just one name server (at first). My setup: Airport Extreme - get's a static ip address from my ISP Mac Mini Server - sits behind the Airport and get's a 10.0.1.2 My problem is that i can't seem to configure DNS correctly. I added a "child nameserver" with my airport's external static ip address at the top level provider, so to my understanding i should have all DNS traffic redirected to my Airport. I've opened port 53 UDP to let the traffic in. Now, what i don't get is this. My Mini Server is sitting on a 10.0.1.2 address and i have setup dns correctly, with an A record to point and resolve my server AND a reverse lookup to that 10.0.1.2. So it's ok for "internal stuff". Here is the clicker... How, when a request comes from the exterior for a reverse lookup, does the server "know" ... well look i have everything in 10.0.1.2 but the guy outside needs something from my real address. I can't begin to describe the MX record bonanza... How do i set this "right"? Do i "need" my Mini Server to sit on the external address directly (i can see how this could be the preferred solution, being close to a "real" server i have in my mind). If not... do i need a PTR record on the 10.0.1.2 server but with the external address in there? My dream: I will extend this "setup" with multiple Mini's in different cities where i work. I want a distributed something (Xgrid comes to mind). PS. Be gentle, i've read 2 books and the subject, and bought both the Lynda Essentials and DNS and Networking to boot, still i'm far from being on top of things.

  Read the article

• Is it possible to create nested classes in PHP as it is in C#?

  - by Edward Tanguay

  In C# you can have nested classes like this, which are useful if you have classes which do not have meaning outside the scope of one particular class, e.g. in a factory pattern: public abstract class BankAccount { private BankAccount() {} private sealed class SavingsAccount : BankAccount { ... } private sealed class CheckingAccount : BankAccount { ... } public BankAccount MakeSavingAccount() { ... } public BankAccount MakeCheckingAccount() { ... } } Is this possible in PHP? I've read that it was planned for PHP 5, then cancelled, then planned again, but can't find definitive info. Does anyone know how to create nested classes (classes within the scope of another class) as in the above C# example using PHP 5.3?

  Read the article

• How to programatically create and read WEP/EAP WiFi configurations in Android?

  - by Als

  How to programatically create and read WEP/EAP WiFi configurations in Android? I have seen a number of people struggling on this very question on various forums and all across the community. I know this is not that straight forward(especially EAP) to figure out because When I wanted to acheive the same I too struggled quite a lot.Well, all the hard work of code analysis and searching various implementations on the internet done with I was finally able to acheive the goal. All the credit goes to number of open source projects and their developers. I would like to share this knowledge with all, Since SO encourages this: "It's also perfectly fine to ask and answer your own question, as long as you pretend you're on Jeopardy: phrase it in the form of a question." Part 1: Creating a WEP WiFi configuration programatically. Part 2: Read a WEP WiFi configuration programatically. Part 3: Read a EAP WiFi Configuration programatically. Part 4: Save a EAP WiFi configuration programatically.

  Read the article

• Create function in python to find the highest of all function arguments, and return the "tag" of the value.

  - by gatechgrad

  Consider the following: p1=1; p2=5; p3=7; highest=max(p1,p2,p3). The max function would return 7. I am looking to create a similar function, which would return "p3". I have created a small function (by simple comparisons) for the above example, shown below. however I am having trouble when the number of arguments go up. def highest(p1,p2,p3) if (p1p2) and (p1p3): return "p1" if (p2p1) and (p2p3): return "p2" if (p3p1) and (p3p1): return "p3". Is there a simpler way to do this

  Read the article

• How to create Empty Label without any entries in it using Google Mail API?

  - by Pari

  Hi, I want to create an empty label in Google apps using Google Mail API. Using Below code: MailItemService mailItemService = new MailItemService(domain, "Sample Migration Application"); mailItemService.setUserCredentials(userEmail, password); MailItemEntry[] entries = new MailItemEntry[1]; entries[0] = new MailItemEntry(); entries[0].Labels.Add(new LabelElement("Empty Label")); entries[0].BatchData = new GDataBatchEntryData(); entries[0].BatchData.Id = "0"; MailItemFeed feed = mailItemService.Batch(domain, username, entries); Above code is not giving any error but not creating label also. If i assign some more values to entries it work nicely but it result in cretion of mail inside Label (But i want empty label) Can anyone help me out here? Thanx

  Read the article

• How to create a new IDA project based on an existing one with different offsets?

  - by tbergelt

  I have an existing IDA Pro project for a C166 processor embedded application. This project already has many functions, variables, etc defined. There are different versions of the embedded application I am looking at. The different versions of the application are 99% the same, but with slight variations in code and data that cause functions and variables to be at different memory offsets. I want to create a new IDA project for a different version of the application. I would like to somehow import all of my function and variable definitions from my existing IDA project. I would like IDA to recognize the signatures of the existing function definitions and define them at there new location in the new project. How can I do this? Are there certain plugins for IDA I can chain together?

  Read the article

• How can I use Three20 to create a dynamic TTThumbsViewController that feeds from a website directory?

  - by Cory Robbins

  Hello, I'm pretty new to the iPhone developing scene, and I am designing an app for a high school band program. Part of the app needs to be an image gallery that retrieves photos from a directory on the band's website and lists them in the thumbnail view. I can't figure out how to create a thumsview that isn't directly linked to specific pictures. I currently have this setup to work with a UIWebView that points to a PHP photo album designed to look like the iPhone Photo Album. This method works, but it is not ideal, and the navigation is obviously a bit less than what would be expected. Is Three20 the right tool for this job? If not, what should I be using? Thanks!

  Read the article

• How would I create a technology standards document for my company?

  - by Rob O

  I'm a Director of Product Engineering for my company. My CEO has asked me to create a technology standards document, explaining things like the technology we use, our policy on adapting to new technology, and design standards like percent of code covered by unit tests. I've never had to do something like this, and I've spent a significant amount of time searching the web for examples, but I haven't found any at all. The closest I've found are documents describing technical specifications for an individual product. However, I'm trying to define this for the entire company. Can someone provide examples of how this document could be formatted/organized, and what the typical content would be? Thanks!

  Read the article

• How to create and remove an html hidden field using jquery?

  - by ChickenBoy

  I am new to javascript and jquery so please bear with me. First of all here is my code so that you can test it to see whats wrong: http://jsfiddle.net/Lzw4e/1/ I want to create a new hidden field every time the user selects from the left <select> element and remove / destroy the hidden field when the user clicks the right <select> element. I used the jquery command $("<input type='hidden' value=selectedAddFootballPlayerId>"); but when I checked of firebug I can't see any hidden field being created. For removal of the hidden field I really don't know. Please help me. Thanks in advance.

  Read the article

• How do I create a point system in a Rails app that assigns points to users and non-authenticated-use

  - by codyvbrown

  I'm building a question and answer application on top of twitter and I'm hitting some snags because I'm inevitably dealing with two classes of users: authenticated and non-authenticated. The site enable users to give points to other users, who may or may not be authenticated, and I want to create a site-wide point system where the application stores and displays this information on their profile. I want to save this point data to the user because that would be faster and more efficient but non-authenticated users aren't in our system, we only have the twitter handle. So instead we display the points in our system like this: @points = point.all( :select => "tag, count(*) AS count", # Return tag and count :group => 'tag', # Group by the tag :order => "2 desc", :conditions => {:twitter_handle => params[:username]}) Is there a better way to do this? Is there a better way to associate data with non-authenticated users?

  Read the article

• How to generate Makefiles with Cmake to create tarballs of project?

  - by Rizo

  I like to keep my Makefiles flexible and multifunctional. One of the tasks I usually add to make command is tar, for example the following instruction does the job: tar: tar -cvf $(PROGNAME).tar $(SRCS) Makefile My question is: How can CMake be used to generate personalized commands like tar? I would like to see some code samples. For the full functionality it would be useful to create project's components and be able to use them as parameters. (Exempli gratia: archive only header files or some specific library). Thanks in advance for your answers!

  Read the article

• How to create a non-persistent Elixir/SQLAlchemy object?

  - by siebert

  Hi, because of legacy data which is not available in the database but some external files, I want to create a SQLAlchemy object which contains data read from the external files, but isn't written to the database if I execute session.flush() My code looks like this: try: return session.query(Phone).populate_existing().filter(Phone.mac == ident).one() except: return self.createMockPhoneFromLicenseFile(ident) def createMockPhoneFromLicenseFile(self, ident): # Some code to read necessary data from file deleted.... phone = Phone() phone.mac = foo phone.data = bar phone.state = "Read from legacy file" phone.purchaseOrderPosition = self.getLegacyOrder(ident) # SQLAlchemy magic doesn't seem to work here, probably because we don't insert the created # phone object into the database. So we set the id fields manually. phone.order_id = phone.purchaseOrderPosition.order_id phone.order_position_id = phone.purchaseOrderPosition.order_position_id return phone Everything works fine except that on a session.flush() executed later in the application SQLAlchemy tries to write the created Phone object to the database (which fortunatly doesn't succeed, because phone.state is longer than the data type allows), which breaks the function which issues the flush. Is there any way to prevent SQLAlchemy from trying to write such an object? Ciao, Steffen

  Read the article

• Can I use a MySQL PREPARE statement in a function to create a query with a variable table name

  - by aHunter

  I want to create a function that has a select query inside that can be used against multiple database tables but I can not use a variable as the table name. Can I get around this using a PREPARE statement in the function? An Example: FUNCTION `TESTFUNC`(dbTable VARCHAR(25)) RETURNS bigint(20) BEGIN DECLARE datereg DATETIME; DECLARE stmt VARCHAR(255); SET stmt := concat( 'SELECT dateT FROM', dbTable, 'ORDER BY dateT DESC LIMIT 1'); PREPARE stmt FROM @stmt; EXECUTE stmt; RETURN dateT; END $$ Thanks in advance for any input.

  Read the article

• When securing MySql, is it better to create a user with root-like priviliges and then remove the 'ro

  - by PoppySeeds

  This would seems to prevent attackers who know that a 'root' user exists?

  Read the article

• Can I create and connect to a SQL Server CE database if SQL Server 2005 isn't installed?

  - by MusiGenesis

  Is there any way to do this? Update: Sorry, I should have included more information. I am trying to create and connect to a SQL CE database using System.Data.SqlServerCe in C# running on a PC (i.e. not running on a Windows Mobile device). This code: string connstr = "Data Source=\"" + filename + "\";Persist Security Info=False;"; System.Data.SqlServerCe.SqlCeEngine engine = new SqlCeEngine(connstr); engine.CreateDatabase(); ... works fine on any PC that has SQL Server 2005 installed, but fails on any PC that doesn't have it installed. I'm trying to find out if there's any way to get this to work without installed SQL Server 2005 on the machine.

  Read the article

< Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >