Search Results

Search found 15323 results on 613 pages for 'db2 connect'.

Page 190/613 | < Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >

  • recent unreliable wireless connection on 10.04 and 10.10

    - by gabkdlly
    Recently, my internet connection over wireless has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista. The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. This problem does not seem to appear when I boot into Ubuntu 9.10 from a live CD ( more precisely, I was able to ping fu-berlin.de for an hour without any packet loss ). Under Ubuntu 10.10, I am experiencing about 33% packet loss. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow ( which happens often ) or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I have observed this problem with a Netgear KWGR614 Router ( with the manufacturers firmware ), as well as with a TP-LINK TL-WR741ND router running OpenWrt. Taking a look at my routers logs, I find many instances of the following line: Tuesday,04 Jan 2011 03:53:01 [TCP SYN Flood][Deny access policy matched, dropping packet] I know that the Netgear router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. I use WEP on the Netgear router and WPA on the TP-LINK to encrypt the wireless connections. Is it possible that someone is jamming my signal ?

    Read the article

  • Connecting / disconnecting DisplayPort causes crash

    - by iGadget
    I wanted to file a bug about this using ubuntu-bug xserver-xorg-video-intel, but the system prompted my to try posting here first. So here goes :-) While the situation in Ubuntu 11.10 was still somewhat workable (see UI freezes when disconnecting DisplayPort), in 12.04 (using Unity 3D) it has gotten worse. The weird part is that during the 12.04 beta's, the situation was actually improving! I was able to successfully connect and disconnect a DisplayPort monitor without the system breaking down on me. But now with 12.04 final (with all updates), it's just plain terrible. When I now connect an external monitor using the DisplayPort connector on my HP ProBook 6550b, it only works sometimes. Most times (but not always!) the screen just goes blank and the system seems to crash (not even CTRL+ALT+F1 works anymore). Only a hard shutdown by keeping the power button pressed for several seconds and then a restart gets me out of this. I suspect the chances of the system crashing become higher as the system's uptime increases, especially when there have been one or more suspend-resume cycles (although I have also experienced this bug once from a cold boot). Disconnecting is roughly the same as with 11.10 (see issue mentioned above), with the difference that if I resume from suspend, I no longer have to do a CTRL+ALT+F1, ALT+F7 cycle to get my screen back. So what more can I try? Or should I just go ahead and file the bug anyway?

    Read the article

  • Machine only responds to network requests from machines it is pinging

    - by ILikeFood
    I have two machines. WOPR: Ubuntu server edition 10.10 LTS 32 bit Adam Selene: Windows 7 home premium 64 bit / Ubuntu Desktop 10.10 LTS 64 bit I want to be able to SSH from Adam Selene to WOPR, so I connect them to the same network. Here's where things get weird. I cannot connect to WOPR in any way under normal circumstances. But, if WOPR is pinging Adam, then it starts responding to ping requests, HTTP gets, and SSH tunnels. I'm an amateur, and brand new to Ubuntu server, so I suspect there's a misconfiguration somewhere, but there's an off chance it's a bug in the OS. Does anyone know what might cause this behavior? Thanks a lot!

    Read the article

  • SDcardReader/Writer is not connected

    - by Insuk
    My IOGEAR sdCardReader/Writer is recongized on Ubutu(by using VM ware) but when I tried to connect to "Removable Devices - Alcor Micro Flash Card Reader/Writer" , the follwoing message is appeared. " The connection for the USB device "Alcor Micro Flash Card Reader/Writer" was unsuccessful. The device is currently in use. " But I think it is not used. Should I use IOGEAR driver for this one? When I connect the card reader, Ubuntu automatically got the "Alcor Micro Flash Card Reader/Writer" . How can I fix the problem? Thank you, Insuk the result of lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 0b95:7720 ASIX Electronics Corp. AX88772 Bus 002 Device 002: ID 0e0f:0003 VMware, Inc. Virtual Mouse Bus 002 Device 003: ID 0e0f:0002 VMware, Inc. Virtual USB Hub Bus 002 Device 004: ID 0e0f:0008 VMware, Inc. Bus 002 Device 005: ID 0403:bcda Future Technology Devices International, Ltd From the vmware log : 2013-10-18T09:00:07.494-06:00| vmx| I120: USB-CCID: Could not establish context: SCARD_E_NO_SERVICE(0x8010001d). 2013-10-18T09:00:07.494-06:00| vmx| I120: USB-CCID: Could not establish context: SCARD_E_NO_SERVICE(0x8010001d).

    Read the article

  • recent unreliable wireless connection with Netgear KWGR614 router

    - by gabkdlly
    Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I know that this router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. Is it possible that someone is jamming my signal ?

    Read the article

  • How to access MySQL when I delete the root user on openSUSE 11?

    - by Negin Nicki
    Unfortunately I deleted MySQL users with the command delete from mysql.user and now I can't access MySQL. I tried looking at MySQL - ERROR 1045 - Access denied, but it is not proper for me because I don't have any user for MySQL. I uninstalled and reinstalled MySQL but I can't access MySQL. What should I do? I wanted to have phpMyAdmin without login and I ruined the whole thing. After uninstalling and having no result, I tried to delete the directories of MySQL and again installing them but again no result and now I have this error: Error 2002:can't connect to local mysql server through socket /var/lib/mysql/mysql.sock I don't have any user to reset the password of, but if I have by reinstalling which I don't know how to connect to MySQL. I tried MySQL -u root I tried MySQL I tried mysqld-safe and etc in the link

    Read the article

  • Solution to wirelessly project tablet desktop?

    - by Robert
    I’m trying to find a device that would allow a windows 7 client to wirelessly connect and display their screen to a projector while still connected to the wireless network. The idea is to allow a professor to still project and display content while walking around the room with their tablet. To date, haven’t been able to find a solution that meets the requirements, has anyone stumbled across one yet? Requirements Must support Windows 7 Must be able to connect to WPA2 Personal(and hopefully enterprise) Must not use any usb dongles – those get lost/damaged given a chance. Goal Wirelessly display screen to projector without cables from tablet/laptop.

    Read the article

  • Media center consumes all available memory when attempting to play music off of a server

    - by RCIX
    I have Windows 7 Ultimate, and recently, when i try to play a song off of my Twonky Media Server/Windows Media Connect (based on an HP WHS with an Atom), it plays choppily. When i open Resource Monitor, it shows that after ordering the music to play, memory usage rapidly spikes to consume most, if not all, of the available memory on my system (excluding a couple hundred megabytes in standby). Why does it do this and is there anything i can do to stop it? Edit: it happens when I attempt to browse the server's music, not just when i play music. Edit 2: the "ehshell" process is what consumes the memory, appears to me something specific to media center. Moreover, the ehshell process doesn't die in this case. Edit 3: It only happens when browsing my Twonky library, and not my Windows Media Connect.

    Read the article

  • Unknown monitor in Lenovo laptop

    - by kumar
    I have set of two Lenovo laptops on which Fedora core 13 is installed. On one machine, the monitor is detected properly such that it is possible to connect another monitor. But on another laptop, the monitor is shown as unknown monitor. I tried to fix it by reinstalling xorg-x11-drv-intel.i686. But the problem remains same (unknown monitor) and it is not possible to connect another monitor with this setting. Laptop model: Lenovo G460. Graphics card: Intel Graphics Media accelerator HD. Thanks!

    Read the article

  • How do I set my router up to authenticate with my service provider?

    - by João Lourenço
    Currently I have this setup: D-Link DSL2640U connected to the phone line: VPI/VCI 0/40, Service Category UBR Without PCR Service pppoe_0_40_3 Interface nas_0_40 Protocol Bridging (LLC/SNAP-Bridging) 802.11q not enabled Bridge Service Enabled Computers have individual PPPoE connections (in Network and Sharing Centre - Set up a new connection or network - Connect to the Internet - Broadband (PPPoE) - Username and Password) How would I move these settings on each individual PC to the router so that all I need to do is connect to the wireless? I have been unsuccessful setting up anything other than Windows PCs on the network (I have tried Macs, iOS and Nokia SmartPhones too). Thanks for the responses in advance!

    Read the article

  • Second monitor not detected

    - by Gabriel
    Hi I have two VGA monitors, my GPU is ATI PowerColor 6850 which has two DVI slots, I use adapters for both VGA monitors. If I connect any the two monitors in the first slot it will work right away (along the plugin confirmation sound). And if I connect any of both monitors to the second slot I won't get anything, nor a signal or confirmation sound. I also tried auto detecting via Catalyst Control Center and Windows Desktop Resolution. I have the latest drivers installed. EDIT: I found this on the Spec Description: Display Connectors DL-DVI-I/SL-DVI-D And in NewEgg: 2 x DVI (1 Single Link, 1 Dual Link) Could this have anything to do with my issue?

    Read the article

  • Creating a network link between 2 very close buildings

    - by Daniel Johnson
    I have a charity who have two adjacent medium sized modern detached houses (in the UK): the buildings stand next to each other and are less than 5 metres apart. They have DSL connected to a single computer in one of the buildings. They want to add a network with wireless, and want it to work across both buildings. Being a charity they need to keep costs down. The network would be used for sharing Word documents, e-mail, browsing and skyping. My initial thoughts were to connect the buildings with fibre. So: Option 1 Use fibre between the buildings. Sufficient cable and two TP-LINK MC100CM Fast Ethernet Media Converters. Cost ~£80.00. But there is the extra cost and hassle of running the cable down and up the external walls, lifting and relaying paving, and burying underground. Never having fitted fibre I'm also a little worried about going up the wall and then bending the cable at 90 degrees to go through the wall and into the building. Option 2 Use two TP-Link TL-WA7510N High Powered Outdoor 5Ghz 15dBi Wireless antennas to connect the buildings. There is a clear line of sight at first floor level. Cost ~£100. And much easier to fit than fibre! Is using the TL-WA7510Ns overkill? Is there something more suitable? I had hoped to use some Netgear stuff, e.g. two DGN2200, one in each house and also use them to provide the wireless link between the buildings. However, in bridge mode wireless client association is not available and repeater mode with client association only supports WEP security which isn't strong enough. Is there something similar that would be up to the job? Option 3 Connect the buildings with UTP cable. My concerns here are risk of electric shock due to a difference of potential between the buildings (or are they so close this shouldn't be an issue) and protection from lightning strikes. Is fitting lighting arrestors expensive? And what can be done to ameliorate against the risk of shock? This all falls outside my area of expertise so I would really appreciate some advice.

    Read the article

  • Configuring Wireless Network

    - by Vinod K
    I have vyataa router on VMware with 2 interfaces eth0 and eth1 eth0 is facing the internet eth0 is in Nat mode with dhcp on eth1 is in bridged mode with my ethernet with ip 10.0.2.34/24 The ethernet card is at ip 10.0.2.95/24 i have defined the nat rule. Hence internet is available at eth1 too. Now i am connecting a wireless router at "eth1" iball router, I have connected the router using a cable to the ethernet interface of my laptop. I have configured the WAN connection type as "Static IP" and given "10.0.2.34/24" All the clients that connect using wireless router cannot connect to the internet though. Could anyone provide me a solution for this.. Thank You!!

    Read the article

  • Corrupted network from ipad

    - by lisa
    All wireless clients were kicked off the network (3 PCs & 1 iPad). Only a PC with a wired connection was still able to connect. This morning I discovered that the network had been renamed and a new password had been assigned. Via Linksys Updater I gave a new password. Strangely, in my Windows Control Panel/Network connections our old password now exists as an unsecured network, that I cannot delete! When I attempt to connect using this bastard network, I get an Apple Push error. Linksys WRT610N PCs all using Windows 7 (wired & wireless) iPad 2

    Read the article

  • Problem accessing MICROSOFT##SSEE database (Error: 18456, Severity: 14, State: 16.)

    - by Philipp Schmid
    After an unexpected server shutdown due to a power failure, I can no longer connect to the internal windows database MICROSOFT##SSEE which is hosting Central Admin for my SBS 2008 server. The log shows: Error: 18456, Severity: 14, State: 16. Login failed for user 'NT AUTHORITY\NETWORK SERVICE'. [CLIENT: <named pipe>] I've tried to connect using the SQL Management studio (connecting to .pipemssql$microsoft##sseesqlquery) but no luck. The SQL Server Configuration Manager doesn't show a entry for 'Protocols for MICROSOFT##SSEE' (but shows it for 2 other database hosted on the same SQL server 2005 Express edition. I have tried to restore the master.ldf and mastlog.log files from a backup, but the issue persists.

    Read the article

  • Restarted computer, now wireless and Visual Studio is broken

    - by Earlz
    I installed the new update for TortoiseSVN which requires a restart. Upon restarting a lot of things broke. I'm currently running a virus scan, but what would cause this? Among the things that no longer work is Visual Studio. It now says "Invalid License Data. A reinstall is required" and my wireless internet does not work. When I go to connect to my network it will say "Can not connect" and then when I diagnose the problem it says "The connection to accesspoint-name was cancelled" (and yes, canceled is misspelt like that) What could have caused this? My computer did not install any updates or anything like that upon restarting and it was running fine before I restarted it.

    Read the article

  • Wireless connected but internet not working, modem is fine because I'm typing over wifi on my android

    - by Sandro Livaja
    I can't connect to the Internet in 11.10. I tried switching my wifi card to another USB slot but nothing changed. Is it possible that the card is able to connect while not being able to receive packages? $ ifconfig eth0 Link encap:Ethernet HWaddr 40:61:86:35:11:b0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:43 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 74:ea:3a:8c:d5:5c inet addr:192.168.2.5 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::76ea:3aff:fe8c:d55c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1209 (1.2 KB) TX bytes:15329 (15.3 KB)

    Read the article

  • Ethernet Connection Unavailable

    - by fabikw
    I'm running Ubuntu Server 12.04 on a laptop with an Intel NIC (driver e1000e). When I connect the ethernet port to the internet (college network, DHCP) it works out of the box. Now I'm trying to connect it to a networked USRP (if you want to know what it is). A friend of mine managed to do this in his laptop (running regular Ubuntu 12.04) just by setting up a new Wired connection in the Network Manager with appropriate addresses. However, when I do the same, no wired connections are available. The output of nmcli -p dev is =========================================== Status of devices =========================================== DEVICE TYPE STATE ------------------------------------------- wlan0 802-11-wireless connected eth0 802-3-ethernet unavailable but the cable is connected to the device and the device is powered up. Any idea how to solve this? UPDATE: After stopping the network-manager service, setting up the connection manually and starting the service again, it now detects the ethernet connection. However, the device still can't receive data and doesn't answer to pings. UPDATE 2: As suggested I tried using a cross over cable but the result is exactly the same. However, I found out that connecting the device to the dock (as opposed to directly to the laptop) works fine. I know that the ethernet port in the laptop works fine, because connecting to the network through it works. Is it possible that the port in the laptop doesn't support Gb Ethernet (because that's what the device requires) but the one in the dock does?

    Read the article

  • Setting up Multiple Routers (as Hardware Firewalls) behind a Home Router

    - by Synetech
    I’ve currently got one computer behind a router with built-in firewall functionality, connected to a home cable-modem that has a single Ethernet port and one IP. I’m going to have to set up another computer for the rest of the family to use which of course will need to be connected to the Internet, probably wirelessly since the modem is in my room and the new system would not be. What I would like to do is to get two more small routers with firewall capability and connect each computer to a router, which would in turn connect to the main router which connects to the cable-modem. That way, both systems have a hardware firewall protecting them (particularly the wireless system) and the burden of blocking would be reduced on both the computer CPUs and the main router because the secondary routers would handle some of the workload. I’m trying to find out about the complexities inherent in this design and how I could set it up to work, specifically the IP handling and NAT aspect. Thanks a lot.

    Read the article

  • connection to apache server switches sockets connection

    - by Newben
    I have just post a question but I post an other one because the problem is not the one I had in thought when asking the latter. So, I am running some rails app on osx, when I run rails s, everything works fine. If I shut down the apache server (mamp) and if I run rails s again, I have this message Can't connect to local MySQL server through socket '/Applications/MAMP/tmp/mysql/mysql.sock', which for sure is normal. For info, my mamp server is running, and the connection must pass through /Applications/MAMP/Library/bin/mysql, so I aliased it by setting in my bash profile : alias mysql="/Applications/MAMP/Library/bin/mysql" Now, when I launch a rails generate command type, I get this message : /$root/vendor/bundle/ruby/2.0.0/gems/mysql2-0.3.11/lib/mysql2/client.rb:44:in `connect': Can't connect to local MySQL server through socket '/tmp/mysql.sock' (2) (Mysql2::Error) So how it can be ?

    Read the article

  • ODBC in SSIS 2012

    - by jamiet
    In August 2011 the SQL Server client team published a blog post entitled Microsoft is Aligning with ODBC for Native Relational Data Access in which they basically said "OLE DB is the past, ODBC is the future. Deal with it.". From that blog post:We encourage you to adopt ODBC in the development of your new and future versions of your application. You don’t need to change your existing applications using OLE DB, as they will continue to be supported on Denali throughout its lifecycle. While this gives you a large window of opportunity for changing your applications before the deprecation goes into effect, you may want to consider migrating those applications to ODBC as a part of your future roadmap.I recently undertook a project using SSIS2012 and heeded that advice by opting to use ODBC Connection Managers rather than OLE DB Connection Managers. Unfortunately my finding was that the ODBC Connection Manager is not yet ready for primetime use in SSIS 2012. The main issue I found was that you can't populate an Object variable with a recordset when using an Execute SQL Task connecting to an ODBC data source; any attempt to do so will result in an error:"Disconnected recordsets are not available from ODBC connections." I have filed a bug on Connect at ODBC Connection Manager does not have same funcitonality as OLE DB. For this reason I strongly recommend that you don't make the move to ODBC Connection Managers in SSIS just yet - best to wait for the next version of SSIS before doing that.I found another couple of issues with the ODBC Connection Manager that are worth keeping in mind:It doesn't recognise System Data Source Names (DSNs), only User DSNs (bug filed at ODBC System DSNs are not available in the ODBC Connection Manager)  UPDATE: According to a comment on that Connect item this may only be a problem on 64bit.In the OLE DB Connection Manager parameter ordinals are 0-based, in the ODBC Connection Manager they are 1-based (oh I just can't wait for the upgrade mess that ensues from this one!!!)You have been warned!@jamiet

    Read the article

  • Is there a way to explore my WHS files via Xbox 360's Media Center app?

    - by bangoker
    I know its a "Console" question but its really more of a Media Center Extender question! I can access the data through the Video/Pictures options, but not through the Media Center App. Also I can only see the videos that are directly on the Videos folder on my WHS, but not any of the subfolders. Same thing in my Laptop, if I connect to my WHS through Media Player it will only show the videos on Videos but not any other sub-folder, but if I open Media Center I can then connect to server and see all the folders.

    Read the article

  • Wireless controllers vs wireless usb hub

    - by David Jensen
    For my htpc i currently only have a steerin wheel as a controller. This is wired and it looks really bad having extended usb wires from the tv to the table. However im thinking of bying some new Gamepads and now comes the question. Should i buy wireless ones or wired and connect them to a wireless usb hub? Having a wireless hub would let me manage my gamepads easily from the couch. A wireless hub also allows me to connect other things that are not input devices from the couch. However im wondering if wireless usb hubs may not be made for input devices in the way that they may not have 100% uptime and probably some delay. Am i right about this?

    Read the article

  • How to restrict access to a specific wireless network to only 1 user profile in Windows 7.

    - by Mathlight
    Hi all, I'm using Win7 SP1. I've got multiple users on the laptop that can / must connect to a wireless network, lets call it Wireless1. I've got an second wireless network, (lets call it Wireless2), which I want to limit access to only the admin user of the laptop. Now I can remove Wireless2 in the network manager every time, but i want a more user friendly solution, so that only the admin can connect to Wireless2, and all the other users cannot ( they may see the network, but must enter the password, like all other networks ). Any ideas?

    Read the article

  • Mirror DFS configuration data between 2 servers/ sites

    - by Retro69
    I have 1 Windows 2008 R2 server in Site A running Domain Integrated DFS in 2008 mode with a Single Namespace with a large number of DFS Targets all configured to point to a share on our NetApp SAN. Step 1. I want to initially copy this configuration data across to a 2012 server in Site A preserving all the configuration data. Step 2. I need to mirror this configuration to a 2nd server in Site B so we dont have a single point of failure for the DFS namespace. For Example. A user in Site B would "connect" to the DFS server in Site B, but if that site was down, it would attempt to connect to the Server in site A and vice versa. Note im not interesting in replicating actual Data here, just the configuration. Our NetApp SANS have mirroring which take care of that. Is this possible? Many thanks.

    Read the article

< Previous Page | 186 187 188 189 190 191 192 193 194 195 196 197  | Next Page >