Search Results

Search found 14179 results on 568 pages for 'reportingservices 2008'.

Page 191/568 | < Previous Page | 187 188 189 190 191 192 193 194 195 196 197 198  | Next Page >

• LAN not picking up gigabit connection through patch panel

  - by user332555

  I have just purchased 2 FVS318G switches to install at my store. How this is set up is the server is in the back room. We have Cat 5E ran up through the ceiling and is patched into a panel in the back room. The 2 switches I just purchased are right next to the server in the back where all the cables patch in. I do a direct connection from the server to switch, avoiding the patch panel completely, and receive 1.0 gbps connection no problem. When i patch in the register computers from the front into the panel and then to the switch I am only getting 100 mbps on the registers up front. The patch panel does say Cat 5E on it but I am not sure if there is any interference in the line somewhere and I cannot get the full 1.0 gbps to the front registers like I want. Any ideas??

  Read the article

• Cannot Ping a server after configuring the Routing and Remote Access Services

  - by stacker

  After configuring the Routing and Remote Access Services to be a both VPN and NAT service, I cannot ping that server anymore from the external side. But when I configure it to be just a VPN server, or just a NAT server, I do able to ping it from the external side. My configuration is like: DC: 192.168.20.11 VPN and NUT: Nic 1: 192.168.20.1, NIC 2: 192.168.147.171 Client: 192.168.147.1 The mask is always: 255.255.255.0 I cannot understand why when configuring the VPN server to be a VPN and NAT, I cannot ping the server anymore.

  Read the article

• Expired password change through VPN failure

  - by Tim Alexander

  I am setting up some new accounts to be used by some contractors. they are going to connect via VPN to our network. My requirement is to set the password initially and then have them change it the first time they log in. As a result the "User must Change Password" box is checked. Loading up a laptop and testing has yielded poor results. When logging in I get a notification that the password has expired and a box to fill in, which I do. it then appears again so I dutifully fill in the password details again. I am then presented with a "Sending Password...." error box with Error:619 listed as the reason. Trying to reconnect then gives a 691 error that the password is bad. From the firewall, that is the actualy VPN server, I can see RAD_ACCESS_DENIED and from the DC running NPS (acting as a RADIUS server for the firewall with MS-CHAP-v2 enabled with the "User can change password after it has expired" checked) I cannot see a request to change the password. I can only see Event ID 4776, 4625 and 6273 (reason 16). I can log in with out the change password flag fine so I know logins are being authenticated. Really hoping someone might be able to assist in tracking down the lack of password change processin gon the DC.

  Read the article

• Fabric and cygwin don't work with windows UNC paths

  - by tcoopman

  I have some strange problems with fabric deployment to Windows Server 2008r2. The thing I try to accomplish is to copy some files to a shared folder with a fabric script (this script does a lot of other things too, but only this step gives me problems). This is the problem: When I try to access a UNC(Universal Naming convention) path I always get access denied kind of answers if I run the script in fabric. When I run the command in an ssh prompt (same user) it works fine. Examples: cmd: robocopy f:/.... //share result: in ssh this works fine, in fabric I get "Logon failure: the user has not been granted the requested logon type aat this computer." cmd: cd //share result: in ssh this works fine, in fabric I get "//share: Not a directory" Further information: uname -a and whoami return exact the same thing in fabric and ssh. I also tried things like mount, net use, but these commands all have kind of the same problem.

  Read the article

• Access Denied on Some Subfolders/Files Within a Share

  - by Tim

  First thing this morning, I find that users on one of our share drives are all getting "access denied". I tried the same drive and also received "access denied" as a Domain Admin. Previous to this, all specified users and admins could get access. I checked share permissions I checked NTFS permissions I temporarily made both types of permissions read/write to "Everyone" -- This worked for one user It turns out that this is occurring for only some files/folders. When I try to manually alter the share of that single share, it can't be shared, access denied. xcacls also gets access denied rebooted the server (not a big deal - this is a smallish company). Does anybody have any insight, my google-fu is coming up blank. Thanks. EDIT: More info, I just ran AccessEnum. There were a lot of "access denied", but I noticed the pattern that all of the access denied had a parent with an owner of "???". When I look at the properties, the "Unable to display owner" message is in the box and I can only make my user account the owner. I can then share the individual file/folder, but it doesn't seem to propogate down to subfolders/files.

  Read the article

• Cannot connect to a VPN server - authentication failed with error code 691

  - by stacker

  When trying to connect to a VPN server, I get the 691 error code on the client, which say: Error Description: 691: The remote connection was denied because the user name and password combination you provided is not recognized, or the selected authentication protocol is not permitted on the remote access server. Now, I validated that the username and password are correct, and tried to login with domain name and without. I also installed a certification to use with the IKEv2 security type. I also validated that the VPN server support security method. But I cannot login. In the server log I get this log: Network Policy Server denied access to a user. The user DomainName\UserName connected from IP address but failed an authentication attempt due to the following reason: The remote connection was denied because the user name and password combination you provided is not recognized, or the selected authentication protocol is not permitted on the remote access server. Any idea of what can I do? Thanks in advance!

  Read the article

• Configuration for httphandler in classic mode

  - by happyspider

  I have to install an httphandler that needs to run on classic mode. I have created an application on the iis that uses a classic apppool and put the handler assembly there. The vendor gave me a configuration in the deployment document that looks like this: <system.web> <globalization requestEncoding="iso-8859-1" responseEncoding="iso-8859-1" /> <httpModules> </httpModules> <httpHandlers> <add verb="*" path="*" type="ProductName.ProductName, ProductName" /> </httpHandlers> </system.web> <system.webServer> <validation validateIntegratedModeConfiguration="false"/> <handlers> <add name="someUnspecificName" path="*" verb="*" modules="IsapiModule" scriptProcessor="C:\Windows\Microsoft.NET\Framework\v2.0.50727\aspnet_isapi.dll" resourceType="Unspecified" requireAccess="None" preCondition="classicMode,runtimeVersionv2.0,bitness32" /> </handlers> </system.webServer> The error I get when requesting a URL on the application is a 404, so I guess the handle is not used at all. Does the configuration look ok for a 64bit system?

  Read the article

• Exchange 2010 outlook anywhere - shows internal URL

  - by Frederik Nielsen

  I am setting up an Exchange 2010 SP2 for a customer. However, the server address that the server returns with autodiscover is wrong, as it points to the internal domain (.local) - and not the external address. How do I change this? Here's an image to describe what I mean: It is the upper field that is wrong. I dont want users to enable the RPC over HTTP-thing, as the users know barely nothing about computers. Thank you in advance.

  Read the article

• SSRS 2005 report manager link not coming up

  - by Mohammed Moinudheen

  On my SQL Server 2005 installation. I am able to view the report server URL but I am unable to logon to the report manager URL. "http://servername/reports" I don't get any error message at all. Only thing is the page never loads and is in a hanged state. From the reporting services log folder, I am unable to see any useful messages getting logged in the log file. I also checked the IIS server logs and didn't get any useful information either. Have anyone of you experienced this before? Is there any way to fix this problem, please share your thoughts.

  Read the article

• CHKDSK always runs on Hyper-V image

  - by Dave

  I am having a problem with one of my VM's. Every time it boots, CHKDSK runs and finds no errors, but it goes into an endless loop (CHKDSK/Reboot/CHKDSK). The only way I can get Windows to boot is by cancelling the chkdsk. Is there any way I can tell windows to not do it? What do you guys suggest? Can't redo server. I guess it's also fair to say I get the following errors in Event Viewer "The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume \Device\HarddiskVolume2" "The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume C:\" I only have 1 VHD attached, not sure what Volume 2 is. Thanks!

  Read the article

• Why would one of my servers stop being able to access other servers by FQDN?

  - by Newlyn Erratt

  I have a number of servers on our local network and our debian server has suddenly stopped being able to access the other servers via their FQDN. Initial symptom was inability to login with Active Directory accounts. On further inspection, this machine, porkbelly, was unable to access our other servers (e.g. bacon and albert) via their FQDN. That is, they can ping albert by running ping albert but not by running ping albert.domain.local though when running ping albert it will be expanded to albert.domain.local. The server is still accessible from other servers via both porkbelly and porkbelly.domain.local. Upon examination of hosts information and running hostname its hostname and FQDN are correct. The resolv.conf appears correct. It contains: domain domain.local search domain.local nameserver 192.168.0.xxx (the nameserver) The dns server is also our Windows AD server. I'm not even sure where to go from here or why dns seems to be partially working though I don't have much experience. Where should I go from here? What might be causing this issue where machines are visible via their hostname but not their FQDN?

  Read the article

• Adding the domain account to a security group on the SQL Server computer that has sufficient privileges to log on as a service

  - by Alberto

  After reading this article, http://www.red-gate.com/supportcenter/content/knowledgebase/SQL_Backup/KB200710000173 I have some problems configuring point 2) and 3): 2) Create a SQL Server login that has the ability to backup (and restore) databases (y) by adding it to the SYSADMIN server role. 3) Add the domain account (x) to a security group on the SQL Server computer that has sufficient privileges to log on as a service, etc. Where can I find detailed instructions on how to accomplish them? Thanks.

  Read the article

• Setting up Mail Server (mx.domain.com) using MailEnable in IIS 7.5

  - by Zee Tee

  I have setup MailEnable Standard on my server and have created the PostOffice (domain/mailbox) for the domain which I intend to be using. I have the DNS settings in GoDaddy like this: A (Host) Host: '@' Points To: IP MX Record Priority: 0 Host: 'mx' Points To: @ Is there anything in IIS that needs to be done to make mx.domain.com work as a mail server that can be used in other domain names? Additionally, On the firewall, I have the Outbound port 25 open, not sure, should I be opening port 25 on Inbound as well?

  Read the article

• install php on server08 manaully

  - by justSteve

  Looking to install php on a 08 box already holding iis/sql box. I've tried the webinstaller a couple times but the installer locks before completion or managing to echo any sort of error message. Before hunting down a manual install how-to i wonder if the box is trying to tell me something i should be paying attention to. PHP running alongside IIS _must be supported or one would expect that error message to be kinda high on the list. any gochas to beware of? thx

  Read the article

• SQL Server Could not register the Service Principal Name

  - by Ice

  How-To Fix this: The SQL Server Network Interface library could not register the Service Principal Name (SPN) for the SQL Server service. Error: 0x54b, state: 3.? Found these line in SQL2008-Server Log on my Vista notebook. Yes my notebook is a member of a 2003 AD domain but now i'm offline. Any ideas?

  Read the article

• PTR record not valid for all domains

  - by charnley

  We have an issue sending emails to certain domains, namely Time Warner and Cox. Last week, we decommissioned our Exchange 2003 server and now our Exchange 2010 server is doing all of the transport for our domain. We run our own authoritative name servers, so we are in charge of the DNS and have modified our PTR record to reflect the new server. All mailflow is working except for these 2 domains. When I telnet on port 25 to the mail servers for Cox and Time Warner I am receiving errors. For Cox the error is: 554... rejected - no rDNS And when I telnet to port 25 to the Time Warner mail server we get this: 554 5.7.1 - Connection refused. IP name lookup failed for x.x.x.x I have run through the outbound SMTP test on Microsoft Remote Connectivity Analyzer and get 100% completely successful results. MXToolbox comes up with all successful tests on SMTP as well, showing correct reverse banner check, and no blacklisting. DNSQueries.com shows a valid reverse DNS entry as well for us. Outbound emails to these 2 domains continue to sit in the queue. Any ideas or advice would be greatly appreciated. Thanks!

  Read the article

• Credentials work for SSMS but not (ODBC) LogParser script

  - by justSteve

  Via SSMS I'm able to connect and navigate the server/db in question. but trying to connect via a logparser script the same credentials fail. I'm trying to execute this from the same box on which the server's running. the username is owner/dbo of the db. The db has mixed mode authentication. [linebreaks for clarity] C:\TTS\tools\LogParserc:\tts\tools\logparser\logparser file:c:\tts\tools\logparser\errors2SQL.sql?source="C:\inetpub\logs\LogFiles\W3SVC8\u_ex100521.log" -i:IISW3C -o:SQL -createTable:ON -oConnString:"Driver={SQL Server Native Client 10.0};Server=servername\SQLEXPRESS;db=Tter;uid=logger2;pwd=foo" -stats:OFF Task aborted. Error connecting to ODBC Server SQL State: 28000 Native Error: 18456 Error Message: [Microsoft][SQL Server Native Client 10.0][SQL Server]Login failed for user 'logger2'. C:\TTS\tools\LogParser

  Read the article

• Application Launcher for Hyper-V Server

  - by peterchen

  We are currently in the process of setting up a HyperV R2 Server machine. Though there's not a lot we need to do wihtin the HyperV Server itself, the command line is sure minimalistic. There are a few administrative / Hardware Monitoring tools that we want to run on he machine itself (accessed through remote desktop). I am looking for a simple program/application launcher where we can hook up these maintenance tools (and one to open a new cmd.exe window in case I habitually close the one I'm working in!) However, all tools I tried by now more or less assume explorer is present, and fail in different ways. Before I go and write a simple one myself, any recommendations?

  Read the article

• Considerations for spanned volumes with SAN's LUN.

  - by Patrick Pellegrino

  I want to know, before going forward, what I can expected in lost of performance (or not) of creating Windows spanned volumes from LUN delivered by a SAN ? I don't know which kind of SAN is (we don't administer it), but they give us 10 300 Gb LUN to our Windows 2k8 R2 (Vmware) and we need larger volume so we think to spanned some disk but we are aware of the performance issue. Any input ? Regards.

  Read the article

• Joining computers to domain when SBS is running in Datacenter

  - by ChrisMuench

  We are contemplating moving our SBS2k8 server to our datacenter. We would be setting up a VPN-VPN tunnel between everything to handle AD. Has anyone done this before? Any particular issues that anyone can remember? So the flow for AD would now become. SBS<-VPN---VPN<-Internal office network

  Read the article

• Windows Server Task Scheduler: Running scheduled executable fail-safe?

  - by Mikael Koskinen

  I have an executable which I've scheduled to run once in every five minutes (using Window's built-in Task Scheduler). It's crucial that this executable is run because it updates few time critical files. But how can I react if the virtual server running the executable goes down? At no point there shouldn't be more than 15 minutes break between the runs. As I'm using Windows Server and its Task Scheduler, I wonder is it possible to create some kind of a cluster which automatically handles the situation? The problem is that the server in question is running on Windows Azure and I don't think I can create actual clusters using the virtual machines. If the problem can be solved using a 3rd party tool, that's OK too. To generalize the question a little bit: How to make sure that an executable is run once in every 5 minutes, even if there might be server failures?

  Read the article

• DNS name not on cert

  - by blsub6

  I've got an interesting one... My users have always typed in 'mail' to get to their mail. There was an internal DNS A record that resolved that to the IP of the mail server. I'm putting in an Exchange server to replace that. In order for people to get their mail, I try putting in an A record that does the same thing as the previous one. When I try to get to OWA, it tells me that the certificate on the server is not trusted. I only have the names: mail.mydomain.com autodiscover.mydomain.com autodiscover.mydomain.internal mydomain.internal mailserver.mydomain.internal so when the browser sees that this cert is trying to cover https://mail/owa it says the cert's not trusted. What amy I supposed to do about that?

  Read the article

• SQL2008 Won't Work After SP1 Install?

  - by leen3o

  I have SQL2008 installed on my Win2008 server, and its been working fine - I have sites running using SQL databases etc.. I thought I would install SQL2008 SP1, but after install I cannot connect to SQL via Management Studio, and in configuration manager I cannot start SQL? TITLE: Connect to Server Cannot connect to #MYINSTANCENAME#. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=-1&LinkId=20476 BUTTONS: OK I'm not really a techie so a bit stuck?? any ideas??

  Read the article

• Why are .local and .arpa DNS queries showing up outside my network on OpenDNS?

  - by Baodad

  We have a Windows office network with a local Actice Directory/DNS domain server. The server is set up with OpenDNS's servers as forwarders (see screenshot). However, when I look at my OpenDNS query statistics, I notice that the 3rd most popular query is *.in-addr-arpa, and the 12th is *.local which is from our local domain. Should I, or how can I prevent these local queries from going beyond my local network?

  Read the article

• Windows Firewall allows connection from any IP regardless of rule that only allow a specific IP

  - by Pierre-Alain Vigeant

  I have configured the Windows Firewall to Block (default) incoming connection on the public profile. I have created a rule for a port (in this case, this is Sql Server) that explicitly states that only my office static IP is allowed. If I test from my office, I am able to connect to the port. I was expecting that anybody outside the office would not be able to connect, but this is not the case. I asked a friend to telnet the port to see if it would reply and it does even if he's not on my network. I am a bit confuse here. Shouldn't it block everybody but the given IP? Is my server completely unsecured?

  Read the article

< Previous Page | 187 188 189 190 191 192 193 194 195 196 197 198  | Next Page >