Search Results

Search found 6612 results on 265 pages for 'seconds'.

Page 192/265 | < Previous Page | 188 189 190 191 192 193 194 195 196 197 198 199  | Next Page >

• Two parts: linux startup script to connect to bluetooth and cron to keep it connected

  - by D.R.

  I have a mini bluetooth keyboard and a Raspberry Pi running a Debian-based distro. I know the MAC address of the keyboard but for this question, let's just use AA:BB:CC:DD:EE:FF. Right now I have to have a wired keyboard connected as well as my bluetooth dongle for the mini-keyboard and on the wired keyboard, I have to run the following when the device boots up: sudo hidd --connect AA:BB:CC:DD:EE:FF If the device goes idle for too long, then the bluetooth disconnects and I have to pull out my wired keyboard and retype that same command. What I'm looking for it a way to have that command run at startup and a way to sense if it gets disconnected so that it will auto reconnect. The annoying thing is that they keyboard has to be in pairing mode (even though it has already been paired) when I run that command, otherwise it tells me the host is down. So perhaps the script needs to prevent it from disconnecting due to inactivity, otherwise I'll have to put it back in pairing mode to reconnect. So to recap: - A script to connect at startup (I can make sure to put the keyboard into pairing mode before turning it on) - A script to prevent it from disconnecting (maybe some sort of signal to send to it every 60 seconds or something?) Any help with this is greatly appreciated! StackOverflow is always the best place to find answers to weird questions! I've been searching long and hard for an answer, but finally had to resort to coming here! Thanks!

  Read the article

• VNC on Xen failure

  - by BCable

  The following config works and creates a good VM in Xen: # Kernel Setup kernel = "/boot/vmlinuz-2.6.18.8-xenU" # Memory memory = "256" # Disk disk = [ "file:/opt/xen/domains/110/sda1.img,sda1,w", "file:/opt/xen/domains/110/swap.img,sda2,w" ] # container name name = "110" hostname = "boo" # Networking vif = ["type=ieomu, bridge=xenbr0"] # VNC vnc = 1 #vfb = [ 'type=vnc,vncdisplay=2,vnclisten=0.0.0.0,vncpasswd=110' ] # Behavior Settings root = "/dev/sda1" extra = "fastboot" But when I uncomment the VFB line, I get the following error after it hangs for at least 30 seconds: [root@customer 110]# xm create boo.cfg Using config file "./boo.cfg". Error: Device 0 (vkbd) could not be connected. Hotplug scripts not working. Any ideas? Part two of this question: Sometimes it actually works, and a port is opened. When this happens, nmap shows the VNC ports open and I can connect via the VNC client, but it just hangs at "Connection established." and no VNC display shows up. I've tried multiple VNC clients (TightVNC, TightVNC Java Console, RealVNC), but they all fail to connect. Does VNC through Xen require X to be started in order to function? I was under the impression that it would show the console screen, so I'm confused as to why all these issues are occurring. Thanks!

  Read the article

• Cannot Connect To VMWare Guest OS Using Either RDP or VNC

  - by Humanier

  Hi, I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). 1) RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: http://lh6.ggpht.com/_yQhsRRimgKU/TArRrtiteQI/AAAAAAAABZA/e96za-y9wzo/rdp_error.JPG 2) RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve mentioned problems. Thank you in advance.

  Read the article

• apache2 + mod_fastcgi + suexec + php5.2 = unstable on high load

  I am hosting several (~30) different sites on one server with apache2+fastcgi+suexec+php5. Sites have different loads and different execution times of their scripts (some of them process request for 5-7 seconds, some <1sek). Sometimes when single site receives very high load (all php instances of this site are created and used) - whole apache server hangs. Apache (worker mpm) creates new processes up to the upper limit. It looks like it is starting to queue ALL new request for EVERY site, not only the one that has high load and quickly achieves process limits... restart of apache solves the problem... config: FastCgiConfig -singleThreshold 1 -multiThreshold 10 -listen-queue-depth 30 -maxProcesses 80 -maxClassProcesses 12 -idle-timeout 30 -pass-header HTTP_AUTHORIZATION -pass-header If-Modified-Since -pass-header If-None-Match (earlier have default -listen-queue-depth = 100, but it didn't change anything...) Any suggestions? Another question - how is implemented this listen queue? is it one queue for whole apache, or unique queue for every defined php apllication (suexec site)? I would like to achieve something like this: when one site receives high load and its queue is full - server bounces next request, but only for this one site.. Other sites should work properly...

  Read the article

• Getting some French-Canadian keyboard strokes to work on English keyboard

  - by Gradient

  I'm trying to use some of the French-Canadian keyboard stokes I'm used to on an English keyboard. I would like to change the behaviour of some keys. I was able to implement these changes in Vim, but I would like them to be applied system-wide (for Windows and Ubuntu). Here's what I want to implement : If I press [a, the character printed is â. When I press [r, something that's supposed to stay normal, the characters printed are [r. If I hold [ for 3 seconds, [ is printed. I want this delay to be applied to all my modified keys. I want to map < to ' and the characters 'e to è. The complex problem here is that I only want the ' beside the ; key to produce the è character, NOT when I press the < (remapped to ') then e. I'll show you a .vimrc file that implements this, now I want this behavior system-wide: set timeout timeoutlen=3000 ttimeoutlen=100 inoremap [a â inoremap [A Â inoremap [e ê inoremap [E Ê inoremap [i î inoremap [I Î inoremap [o ô inoremap [O Ô inoremap [u û inoremap [U Û inoremap 'a à inoremap 'A À inoremap 'e è inoremap 'E È inoremap 'u ù inoremap 'U Ù inoremap }e ë inoremap }E Ë inoremap }i ï inoremap }I Ï inoremap }u ü inoremap }U Ü inoremap ]c ç inoremap ]C Ç inoremap / é inoremap < '

  Read the article

• The USB mouse sticks in Windows 7 after automatic attempt to fix the boot

  - by chelder

  Avast Antivirus asked me to delete a probable virus and to restart to perform a checking. I had to stop the checking at the middle of the procedure as I needed the computer. It was imposible to turn off the computer pushing the power button (as it entered in suspension mode, no matter how long I kept pushed the power button). I removed the battery as the only way to restart the computer. Windows 7 said that there is a problem to iniziate Windows. Windows 7 tried to fix the problem without success. Windows 7 started after that though. Everything is OK but the USB mouse. The USB mouse sticks and freezes each couple of seconds more or less. The tactile mouse (PS2) works well. I googled for solutions but the posible solutions didn't work for me. What happened? How could I fix it without formatting and reinstalling everything? UPDATE: this is what I did: Change the mouse from one usb port to another Test another mouse Set the number of cores of the CPU manually with msconfig Power management: not disable usb ports Check hard disk errors

  Read the article

• Cannot Connect To VMWare Guest OS Using Either RDP or VNC

  - by Humanier

  Hi, I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). 1) RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: http://lh6.ggpht.com/_yQhsRRimgKU/TArRrtiteQI/AAAAAAAABZA/e96za-y9wzo/rdp_error.JPG 2) RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve mentioned problems. Thank you in advance.

  Read the article

• Sluggish Windows SBS 2003

  - by TomWilsonFL

  One of my customers has a Windows 2003 Small Business Server which at this point is basically the DC, DNS, Fileserver and Symantec Protection Manager. I have disabled Exchange because I moved their mail to Google Apps. The server is extremely sluggish when doing anything. It is most noticeable when a dialog box is open (say the System properties), and you try to change tabs. This is usually instant, but on this machine can take 3-5 seconds. What additional services / packages can I uninstall from this machine knowing that it is only performing the above roles? Will removing the "Small Business Server" package in Add / Remove Programs get rid of a few unnecessary things? Any other thoughts? P.S. I know Symantec Endpoint and the Protection Manager are hogs, but I have nothing to replace the solution with at the moment. Thanks, Tom UPDATE: I looked over the different performance metrics, but nothing stood out as a problem. One of my friends mentioned Symantec's log and temp files can get quite huge and slow things down, so I ran CCleaner on the machine and found close to 3 GB of Symantec "stuff." Removed that and now the machine is MUCH better. I am still unsure why the data just sitting there would cause such a slowdown. The drive is not even near full. The only thing I can imagine is that Symantec must have to run through this stuff now and then.

  Read the article

• dhclient requests filling memory?

  - by shanethehat

  Dammit Jim, I'm a web developer, not a sys admin. With that out of the way, my client's has a CentOS server (6.2) that is only serving a single Magento site (and the associated MySQL server) and it is frequently running out of memory, despite the site only currently being open to 5 users. I'm investigating the logs to try to figure out why the memory usage is so high, but I don't really know what I'm looking at. It seems that there are a lot of entries in /var/log/messages concerning DHCP requests, approximately one every 15 seconds, that look like this: Apr 7 14:23:06 s15940039 dhclient[815]: DHCPREQUEST on eth0 to 172.30.102.85 port 67 (xid=0x6b5cd2a7) Is this normal? I don't see anything else in here that I don't recognise, but then I'm not sure I'd know the problem if I did see it. 4 days ago the server ran out of memory completely and locked up, requiring a restart. The DHCP messages did not start up again for 23 hours, but then carried on as before. I have read this question which describes the same issue, but in my case a fresh DHCP lease does not ever seem to be issued. Is this something I should push back to the hosting provider, or have I not yet found the source of the memory problem?

  Read the article

• PHP crashing during oAuth scripts

  - by FunkyChicken

  I just installed Nginx 1.2.4 and PHP 5.4.0 (from svn) (php fpm). CentOs 5.8 64 The problem I have is that PHP crashes the moment I run any social oAuth scripts. I have tried to log into Facebook, Twitter and Google with various scripts that I know work on my other servers. When I load the scripts I get a 502 error from Nginx. And I find these errors in the log: in php-fpm log: WARNING: [pool www] child 23821 exited on signal 11 (SIGSEGV) after 1132.862984 seconds from start in nginx log: ERROR: recv() failed (104: Connection reset by peer) while reading response header from upstream From what I can see, it goes wrong when PHP tries to make a request to any of the oAuth servers. https://github.com/mahmudahsan/PHP-SDK-3.0---Graph-API-base-Facebook-Connect-Tutorial-Source for example is one of the scripts that works perfectly on my other machines, but causes PHP to crash. I found: http://stackoverflow.com/questions/3616191/nginx-php-fpm-502-bad-gateway which seems to be a similar problem, but I cannot find a way to solve it. +++ UPDATE +++ Now I have been doing some debugging in 1 of the scripts that is playing up. If you go to line 808 http://pastebin.com/gSnzRtXb it runs the curl_exec() command. When that is ran, it crashes. If i echo'test';exit; just above that line, it echo's correctly, if i do it below that line, php crashes. Which means it's that line 808 which causes the crash. So I made a very simple script to do some testing: http://pastebin.com/Rshnyhcm which also uses curl_exec, but that runs just fine. So I started to dig deeper into that query from the facebook script to see what values the $opts array contains from line 806. Output of that array is: http://pastebin.com/Cq9ffd3R What the problem is, I still have no clue :(

  Read the article

• How should I configure my Active Directory servers so that if one goes down, users are not kicked off SQL?

  - by Matty Brown

  Today, we shut down one of our Active Directory servers during office hours to check the loading on a UPS. Since all the server did was provide Active Directory in a separate building incase the main building caught fire, or whatever, we didn't think it would have any effect on our users. Seconds after the server was shut down, we had a dozen phone calls from users experiencing this issue:- [Microsoft SQL Server Login] SQLState: '28000' [Microsoft][ODBC SQL Server Driver][SQL Server]Login failed. The login is from an untrusted domain and cannot be used with authentication. Once we realized what had happened, we quickly rebooted the down Active Directory server. Problem solved. But why did this happen. And what if one day a server has a breakdown and is offline for hours, or days? Shouldn't the other Active Directory servers in the domain service authentication requests without disruption to users? We have 3 Windows Server 2003 Standard servers running Active Directory as Domain Controllers with Global Catalogs, all physically located on the same network at Gigabit speeds. I believe the domain was originally Windows Server 2000, or maybe even NT 4.0. Could the issue be to down to old Group Policies inherited from these old server OS's, or some default setting in Active Directory that needs changing?

  Read the article

• Performance: Nginx SSL slowness or just SSL slowness in general?

  - by Mauvis Ledford

  I have an Amazon Web Services setup with an Apache instance behind Nginx with Nginx handling SSL and serving everything but the .php pages. In my ApacheBench tests I'm seeing this for my most expensive API call (which cache via Memcached): 100 concurrent calls to API call (http): 115ms (median) 260ms (max) 100 concurrent calls to API call (https): 6.1s (median) 11.9s (max) I've done a bit of research, disabled the most expensive SSL ciphers and enabled SSL caching (I know it doesn't help in this particular test.) Can you tell me why my SSL is taking so long? I've set up a massive EC2 server with 8CPUs and even applying consistent load to it only brings it up to 50% total CPU. I have 8 Nginx workers set and a bunch of Apache. Currently this whole setup is on one EC2 box but I plan to split it up and load balance it. There have been a few questions on this topic but none of those answers (disable expensive ciphers, cache ssl, seem to do anything.) Sample results below: $ ab -k -n 100 -c 100 https://URL This is ApacheBench, Version 2.3 <$Revision: 655654 $> Copyright 1996 Adam Twiss, Zeus Technology Ltd, http://www.zeustech.net/ Licensed to The Apache Software Foundation, http://www.apache.org/ Benchmarking URL.com (be patient).....done Server Software: nginx/1.0.15 Server Hostname: URL.com Server Port: 443 SSL/TLS Protocol: TLSv1/SSLv3,AES256-SHA,2048,256 Document Path: /PATH Document Length: 73142 bytes Concurrency Level: 100 Time taken for tests: 12.204 seconds Complete requests: 100 Failed requests: 0 Write errors: 0 Keep-Alive requests: 0 Total transferred: 7351097 bytes HTML transferred: 7314200 bytes Requests per second: 8.19 [#/sec] (mean) Time per request: 12203.589 [ms] (mean) Time per request: 122.036 [ms] (mean, across all concurrent requests) Transfer rate: 588.25 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 65 168 64.1 162 268 Processing: 385 6096 3438.6 6199 11928 Waiting: 379 6091 3438.5 6194 11923 Total: 449 6264 3476.4 6323 12196 Percentage of the requests served within a certain time (ms) 50% 6323 66% 8244 75% 9321 80% 9919 90% 11119 95% 11720 98% 12076 99% 12196 100% 12196 (longest request)

  Read the article

• Windows 2008 64bit: applications and explorer always hang

  - by Phil Farthing

  I setup a couple of Window 2008 64bit systems about 5 months ago. Initially all seemed well. Now however, for no apparent reason, things are dog slow, apps hang, explorer hangs, just clicking on something can cause a CPU spike of 100%, and often it's explorer that is eating it up. As I have two on identical hardware, and they experience the same problem, it doesn't seem related to addon software. The only thing these have in common is Kaspersky and I've tried disabling/uninstalling to no avail. There are no useful error messages in the event logs. Actually, the system never even reports app hangs. Sometimes, it similar to what I've seen on Windows 7 systems where the screen goes milky and asks if I want to trouble shoot, that's only when get impatient and click happy. The really odd thing, is that it will NOT do this for a few minutes at a time, and then starts up again. Like I will click on the start menu and browse for the Admin Tools, the start menu will hang at some point and I'll have to wait about a minute, then it's OK. The next time I do this, a few seconds later, it's fine. Every click seems to hang the first time around, then be ok the second time if I do the exact same thing. If anyone has any suggestions, please PLEASE let me know! thanks =)

  Read the article

• Why won't dhclient use the static IP I'm telling it to request?

  - by mike

  Here's my /etc/dhcp3/dhclient.conf: request subnet-mask, broadcast-address, time-offset, routers, domain-name, domain-name-servers, domain-search, host-name, netbios-name-servers, netbios-scope, interface-mtu; timeout 60; reject 192.168.1.27; alias { interface "eth0"; fixed-address 192.168.1.222; } lease { interface "eth0"; fixed-address 192.168.1.222; option subnet-mask 255.255.255.0; option broadcast-address 255.255.255.255; option routers 192.168.1.254; option domain-name-servers 192.168.1.254; } When I run "dhclient eth0", I get this: There is already a pid file /var/run/dhclient.pid with pid 6511 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/eth0/00:1c:25:97:82:20 Sending on LPF/eth0/00:1c:25:97:82:20 Sending on Socket/fallback DHCPREQUEST of 192.168.1.27 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.27 from 192.168.1.254 bound to 192.168.1.27 -- renewal in 1468 seconds. I used strace to make sure that dhclient really is reading that conf file. Why isn't it paying attention to my "reject 192.168.1.27" and "fixed-address 192.168.1.222" lines?

  Read the article

• a disk read error occurred

  - by kellogs

  Hi, ¨a disk read error occurred¨ appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I can not recall how exactly have I used testdisk but it once said that ¨The harddisk /dev/sda (160GB / 149 GB) seems too small! (< 172GB / 157GB)¨ or something simillar. So far I have tried to ¨fixboot¨ and ¨chkdsk¨ from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please ? Thank you!

  Read the article

• Windows Media Center doesn't see my movies

  - by DrJekyll

  I am trying to configure my Windows Media Center (Windows 7 Ultimate). I selected folder with my movies and added it to the library, but when I went to the movies library, it says "There are no items in this library yet - Windows Media Center is searching for media files in the background...". I have all necessary codecs installed, Windows Media Player opens those movies correctly. When I right click on the file - Open with - Windows Media Center it also plays them without any problem. Any ideas why they don't appear in the libraries? Edit: Movies are coded with divx and xvid codecs and they have ".avi" extension. Windows doesn't have problems playing them. I told Media Center where the files are. I even pointed Windows Media Center to a folder with only one .avi file it still couldn't find anything there. (I have given it quiet some time, even though searching in the directory with only one file shouldn't take more than a few seconds.) When I add a folder with a lot of movies, I get a dialog box "You can wait while media is added or select OK to continue using Windows Media Center.".                                                                        At the end it says it added about 90 movies, but when I go to the libraries, it's still empty.

  Read the article

• FreeBSD ZFS RAID-Z2 performance issues

  - by Axel Gneiting

  I'm trying to build my own network attached storage based on FreeBSD+ZFS+standard components, but there are strange performance issues. The hardware specs are: AMD Athlon II X2 240e processor ASUS M4A78LT-M LE mainboard 2GiB Kingston ECC DDR3 (two sticks) Intel Pro/1000 CT PCIe network adapter 5x Western Digital Caviar Green 1.5TB I created a RAID-Z2 zpool from all disks. I installed FreeBSD 8.1 on that zpool following the tutorial. The SATA controllers are running in AHCI mode. Output of zpool status: pool: zroot state: ONLINE scrub: none requested config: NAME STATE READ WRITE CKSUM zroot ONLINE 0 0 0 raidz2 ONLINE 0 0 0 gptid/7ef815fc-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/80344432-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/81741ad9-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/824af5cb-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 gptid/82f98a65-eab6-11df-8ea4-001b2163266d ONLINE 0 0 0 The problem is that write performance on the pool is very very bad (<10 MB/s) and every application that is accessing the disk is unresponsive every few seconds when writing. It seems like writing is fine until the ZFS ark cache is full and then ZFS stalls the entire system I/O till it's finished writing that data. Also I'm getting kmem_malloc to small kernel panics. I've already tried to put vm.kmem_size="1500M" vm.kmem_size_max="1500M" into /boot/loader.conf, but it doesn't help. Does anyone know what's going on here? Am I really not having enough memory for ZFS to handle this RAID-Z2?

  Read the article

• Apple Magic Trackpad 3-Finger Drop Lag

  - by activestylus

  After enabling three-finger dragging for my Trackpad, I notice that it drags well, but when I release there is about 1-2 seconds of lag before it actually drops. I understand this is supposed to be a feature so when you run out of space to drag, you have time to move your hand. But, for those of us powerusers, who move really fast, this is a BUG, not a feature. There should be some way to turn it off! For some perspective, I personally own a Fingerworks trackpad as well (the company Apple bought to make the Trackpad) and it does not suffer this problem. Drops are instantaneous no matter what program I am in. This is hugely frustrating for me, because I thought I was upgrading here and Apple's version does not perform as well as the Fingerworks model (which I purchased in 2004) I actually made a short video illustrating the problem, and why it is so frustrating for anyone who uses the pad as an artistic tool. Anyone here face this problem? If not, how would you recommend that I address Apple directly about this? PS - Already looked at this thread and the conclusion does not help me. I do not have one-finger drag enabled. PPS - I understand that for most people this is not an issue because they use the 'click' feature of the Trackpad. However, after years of using Fingerworks and not having to click ever, I find that it slows me down.

  Read the article

• Windows Explorer slow to open networked computer, fast to navigate once opened

  - by Scott Noyes

  I open Windows Explorer and enter an IP for a computer on my home network (\\192.168.1.101). It takes 30 seconds or more to present a list of the shared folders. It does not appear to be an initial handshaking/authentication thing; even if I allow the view to load and then immediately load the same again, it is always slow. Once they appear, navigating through folders and opening files is fast. Also, navigating directly to a folder (\\192.168.1.101\My Music) is fast, even if it's the first connection since a restart. Using \\computerName instead of the IP address gives exactly the same results. Pings return in 1ms. net view \\computerName (or \ipAddress) returns the list of shared folders fast. This makes me suspect an Explorer issue rather than a network issue. Suspecting that the remote computer was being automatically indexed or something, I went into Tools-Folder Options-View and unchecked "Automatically search for network folders and printers," but that made no difference. De-selecting the "Folders" icon near the address bar makes no difference. Adding the IP address and computer name to the hosts file makes no difference. Both computers involved are laptops running Windows XP. Both have WiFi and cable adapters. Mine is not connected via cable. The result is the same whether the target is plugged in to the cable or not (although the IP address changes - 192.168.1.101 over cable, 192.168.1.103 over WiFi.) We are using DHCP assigned by the router.

  Read the article

• Mac Mini's internet very slow, every other device fine (PC, iPhone, Xbox 360)

  - by alex

  I recently haven't used my Mac Mini for about 5 days (however it was left on). I seem to be able to connect and get great download / upload speeds through my PC, Xbox 360, iPhone and parents' laptop. However, my Mac Mini is very slow. OS X's Mail.app is downloading mail at 0.4kbps and then dropping to 0. Skype file transfers are doing the same. Browsing the net is a terrible experience. It is taking 30 seconds or more to download basic pages. All of my devices connect wirelessly to a Netgear router / modem. I have tried giving the Mac Mini a manual IP, and renew DHCP lease, as well as flush DNS in Terminal. I have also rebooted the router / modem twice, and the Mac Mini twice. Do you know what could be causing this? Thanks Update This is very weird. It is also very slow accessing localhost (setup through MAMP) and also slow to access the Netgear router config pages.

  Read the article

• Need for explanation: NetBIOS over TCP/IP on VMware network adapter disturbs access to network share

  - by gyrolf

  (Moved here from StackOverflow) Some time ago nearly all workstations in our team (Windows XP SP2) exhibited intermittend but frequent delays when accessing shares on the network. Typically the first access to a share which hadn't been accessed for some time resulted in a nearly frozen workstation for up to 30 seconds. Then everything started working fine again. Using TCPView from Sysinternals I saw that during this delays there was a connection to the netbios-ssn port on the file server which was in state SYN_SENT. First try: Disable NetBIOS over TCP/IP for the intranet network adapter. Problem solved, but I didn't like to manipulate our centrally managed network configuration for the intranet. Second try: Disable NetBIOS over TCP/IP only for the VMWare network adapter (VMNet1 used for host only communications). Problem solved again! My questions: Why does NetBIOS over TCP/IP on one network adapter disturb NetBIOS over TCP/IP on another network adapter? Is this problem specific to VMWare network adapters? Has anybody else seen this phenomen? Additional information: VMWare Workstation version 6.0.3 At the time I started seriously analysing the problem it was no more possible to find out what had been changed to our systems at the time the problems started.

  Read the article

• ipmi - can't ping or remotely connect

  - by Fidel

  I've tried configuring the IPMI controller to accept remote connections, but I can't even ping it. Here is it status: #/usr/local/bin/ipmitool lan print 2 Set in Progress : Set Complete Auth Type Support : NONE PASSWORD Auth Type Enable : Callback : : User : NONE PASSWORD : Operator : PASSWORD : Admin : PASSWORD : OEM : IP Address Source : Static Address IP Address : 192.168.1.112 Subnet Mask : 255.255.255.0 MAC Address : 00:a0:a5:67:45:25 IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10 BMC ARP Control : ARP Responses Enabled, Gratuitous ARP Enabled Gratituous ARP Intrvl : 8.0 seconds Default Gateway IP : 192.168.1.1 Default Gateway MAC : 00:00:00:00:00:00 802.1q VLAN ID : Disabled 802.1q VLAN Priority : 0 RMCP+ Cipher Suites : 0,1,2,3 Cipher Suite Priv Max : uaaaXXXXXXXXXXX : X=Cipher Suite Unused : c=CALLBACK : u=USER : o=OPERATOR : a=ADMIN : O=OEM # /usr/local/bin/ipmitool user list 2 ID Name Enabled Callin Link Auth IPMI Msg Channel Priv Limit 1 true false true true USER 2 admin true false true true ADMINISTRATOR # /usr/local/bin/ipmitool channel getaccess 2 2 Maximum User IDs : 5 Enabled User IDs : 2 User ID : 2 User Name : admin Fixed Name : No Access Available : callback Link Authentication : enabled IPMI Messaging : enabled Privilege Level : ADMINISTRATOR # /usr/local/bin/ipmitool channel info 2 Channel 0x2 info: Channel Medium Type : 802.3 LAN Channel Protocol Type : IPMB-1.0 Session Support : multi-session Active Session Count : 0 Protocol Vendor ID : 7154 Volatile(active) Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available Non-Volatile Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available # /usr/local/bin/ipmitool chassis status System Power : on Power Overload : false Power Interlock : inactive Main Power Fault : false Power Control Fault : false Power Restore Policy : unknown Last Power Event : Chassis Intrusion : inactive Front-Panel Lockout : inactive Drive Fault : false Cooling/Fan Fault : false # arp Address HWtype HWaddress Flags Mask Iface 192.168.1.112 ether 00:A0:A5:67:45:25 C bond0 # /usr/local/bin/ipmitool -I lan -H 192.168.1.112 -U admin -P admin chassis power status Error: Unable to establish LAN session Unable to get Chassis Power Status In summary. It exists on the ARP list so arp's are being broadcast. I can't ping it and can't connect to it. Can anyone spot any glaring mistakes in the configuration? Many thanks, Fidel

  Read the article

• Can Safari 5.1 for Mac OS display favicons for bookmarks in the Bookmarks Bar?

  - by Greg R.

  When bookmarking a web site, most contemporary browser will display the site's favicon next to the bookmark, both in the bookmark view and the bookmark toolbar. This is a useful feature. In the bookmark toolbar you can edit the name of the bookmark to be blank, effectively leaving the favicon there as an easily identifiable "button" from which to launch the bookmark. This allows you to make more effective user of the space in the bookmark toolbar. I use this approach effectively in Firefox, Chrome, and IE. For example, here is a portion of my Bookmarks Toolbar from Firefox: However, in Safari, no favicon is ever displayed for bookmarks. In the full bookmark view only a generic globe icon is displayed. In the Bookmark Bar in Safari, no icon at all is displayed. Which means the habit of removing the bookmark name & leaving the favicon is useless. Here's what the same configuration (synced between browsers via Xmarks) looks like in Safari. That blank space is where the favicons should be. The boomark is there -- if you hover over it, the blank space changes color to indicate the presence of a bookmark and a tool tip will with the URL will pop up after about two seconds. However, it's really quite unusable. So. The question: is there an extension, plug-in, or modification of some sort that will enable the display of favicons for bookmarks in Safari (OS X Lion 10.7.3 , Safari version 5.1.3)?

  Read the article

• Dell XPS 15 L502X hard drive Partition

  - by Mohan Gajula

  I have a situation here. I got my new Dell XPS 15 Laptop. The configuration of hard drive is as below : Volume 1: (OEM Partition): 133MB Volume 2: OS (C:): 685.25 GB Volume 3: Recovery : 13.25 GB Now, I am trying to re-partition my C Drive to have a C: drive with 100 GB and a new drive with 585 GB. Earlier, I tried using the Windows 7 Disk Management to shrink and extend the volume. That lead to the OS and hard drive not working. Dell Tech support tried to fix the issue, but they were not able to fix the issue online. Later a Dell Technician arrived my place, and replaced the hard drive with a new hard drive. Please help me re-partition the C: Drive with 100 GB, and new D drive with 585 GB. I don't want to lose my Recovery Partition. SOLUTION As Suggested by KCotreau below , I have done exactly. I have resized the C drive to 100 GB. And then applied the changes. Windows got restarted. On the boot screen, the partition was taking place. It took around 30 mins ( approx. ). Once after restart, I can see my C drive is 100 GB. Now opened the Easeus again. And created a new partition for the free space ( 585 GB ) this took 10 seconds to create. Here goes the screenshot after partitioning. Thanks to KCotreau. You are amazing.

  Read the article

• ddclient to update namecheap subdomain?

  - by LF4

  I have a subdomain that I want to update with ddclient. I configured the ddclient to get the IP from dyndns but it's not updating the subdomain on namecheap. They said to use yourdomain.com as the login instead of my actual domain. Has anyone been able to get namecheap DNS updated with ddclient? I'm running CentOS 6.2 with ddclient 3.7.3. When I run ddclient I get the following. CONNECT: checkip.dyndns.org CONNECTED: using HTTP SENDING: GET / HTTP/1.0 SENDING: Host: checkip.dyndns.org SENDING: User-Agent: ddclient/3.7.3 SENDING: Connection: close SENDING: RECEIVE: HTTP/1.1 200 OK RECEIVE: Content-Type: text/html RECEIVE: Server: DynDNS-CheckIP/1.0 RECEIVE: Connection: close RECEIVE: Cache-Control: no-cache RECEIVE: Pragma: no-cache RECEIVE: Content-Length: 106 RECEIVE: RECEIVE: <html><head><title>Current IP Check</title></head><body>Current IP Address: IPADD</body></html> Use of uninitialized value in string ne at /usr/sbin/ddclient line 1998. WARNING: skipping update of lf4bot from <nothing> to IPADD WARNING: last updated <never> but last attempt on Fri Jun 15 22:46:21 2012 failed. WARNING: Wait at least 5 minutes between update attempts. ddclient.conf File daemon=300 # check every 300 seconds syslog=yes # log update msgs to syslog mail=root # mail all msgs to root mail-failure=root # mail failed update msgs to root pid=/var/run/ddclient.pid # record PID in file. ssl=yes # use ssl-support. Works with use=web, web=checkip.dyndns.org/, web-skip='IP Address' # found after IP Address protocol=namecheap \ server=dynamicdns.park-your-domain.com \ login=yourdomain.com \ password=PASSWORD \ lf4bot

  Read the article

< Previous Page | 188 189 190 191 192 193 194 195 196 197 198 199  | Next Page >