Search Results

Search found 5728 results on 230 pages for 'power conditioning'.

Page 194/230 | < Previous Page | 190 191 192 193 194 195 196 197 198 199 200 201  | Next Page >

• I think my laptop just died

  - by Joel Coehoorn

  I have a Dell 1330M that as of about 15 minutes ago will no longer POST. What happened was I was working, stepped away for a moment, and when I came back it was turned off. I thought that was odd, but turned it on and things seemed fine. About 1/2 hour later it crashed and restarted, but came up fine again. It did this once more. At this point I was starting to get worried, but I hadn't had any problems with the laptop before and every crash was after doing some work in a virtual machine that I don't often use, so I at put the blame there. It didn't feel like it was overheating anywhere and there's no ozone smell of overheated electronics. Then it crashed a final time and now when I turn it on all I see is a bright screen with a bunch of vertical lines (noise). I've tried removing the memory sticks one at a time, but I get the same result with either memory stick in either slot. With no memory at all it stops earlier in the POST process and the screen is completely blank (black, no backlight). As I type this, I hear a double beep from the system about once every 10 minutes. I'm pretty sure the hard drive is fine because it fails during post, before anything off the drive is needed. The power supply seems good because the screen is nice and bright. It's not the RAM because swapping that around made no difference. The leaves motherboard (which I doubt and can replace) and CPU (which just might be changable). Any ideas? Is there any hope for this laptop? I'm rather fond of it and I'd have a hard time replacing it with anything near as nice.

  Read the article

• Win 7 crashes, PC reboots and says "Hard drive 0 not found" until I turn if off and on again

  - by Danny T.

  I recently made the move from Windows XP to Windows 7. Since then, when my computer is on for a few hours it always ends up rebooting without warning. Then the BIOS won't recognize my hard drive (hard drive 0 not found). If I turn off my computer and then on again, it boots normally. Some details: Dell Dimension 9150 Windows 7 I updated the BIOS I updated all system drivers with the latest version from Dell (SATA, Chipset, etc.) Other drivers updated too (Graphic card, sound, etc.) There is one thing that I tried after some Googling: I turned off the DMA access to the drives, but it's still rebooting after a few hours. Any clue? UPDATE 2010/12/13 Here are the events from the Event Log for today, from when I turned the computer on until it crashed: 19:17 - Error - ID 10016 - DistributedCom 20:06 - Error - ID 1008 - Customer Improvement Program (could not send data to Microsoft) 21:48 - Critical - ID 41 - Kernel-Power (System was restarted without proper shutdown) 21:48 - Error - ID 6008 - EventLog (Previous system down was not planned) 21:48 - Error - ID 1101 - EventLog (Audit Event ignored) 21:49 - Error - ID 10016 - DistributedCom Both DistributedCom events have a description along these lines (translated from French): The authorisation parameters specific to the application are not allowing Local Execeution for the COM server application with the CLSID {C97FCC79-E628-407D-AE68-A06AD6D8B4D1} and the APPID {344ED43D-D086-4961-86A6-1106F4ACAD9B} to the SID AUTHORITY NT\User System (S-1-5-18) from the address LocalHost (LRPC usage). This security authorisation can be changed with the Component service administration tool. UPDATE 2010/12/31 Here are the error messages I have on blue screens : STOP C000007xA - Kernel_Data_Inpage_Error "Unkown hard error" C00000135 - Can't start because &hs is missing

  Read the article

• Platform to allow users to suggest and vote for ideas

  - by Simon

  I head up a support team for a software product. I am in the process of setting up a blog (Wordpress.org), a forum (PHPBB or maybe Vanilla), a means to view bugs (probably expose Jira), but would also like to allow our customers to suggest enhancement requests. Currently we have this as a 'contact form' via the blog, which feeds into a dedicated inbox, which the product manager reviews and may include some of these ideas into the product. However, I would like to give the clients more power/visibility over this. Have a look at ideas.arcgis.com. There are plenty of other similar sites as well. Users can suggest new ideas Other users can vote these ideas up or down (similar to Stack Exchange sites) Ideas that are voted highly will be given a higher priority over lower ones. We can report back on the # of ideas we implement, and potentially reject ideas with reasoning. Has anyone seen any platforms (ideally free) which would replicate something similar to this? I was half thinking of embedding Vanilla within a wordpress page, but need to look into it more.

  Read the article

• Can a OS be copied from one hard drive to another and still boot?

  - by AlexMorley-Finch

  Background My computer gets stuck on the make and model screen after the BIOS screen, aka the Toshiba screen. After some research I've realized that the problem is the hard drive. I'm using an old 250gb model that USED to be used for backup purposes, however I loaded windows 7 ultimate onto it This hard drive has trouble getting up to full RPM therefore cannot boot correctly until its warmed up. meaning that my pc needs to be restarted several times before it boots (once it took my 13 reboots to get my pc on!) From my research its either that, or lack of power supply, and I've tried multiple PSUs. Question I have my OS and all my files on this 250gb HDD... If I were to literally open the explorer, and copy EVERYTHING (including hidden files obviously) from this 250gb, to a spare 500gb I've got knocking about... Will it boot if I just copy everything? I cannot be bothered to load another OS onto my PC so if there is a way I can just copy the existing one over from one HDD to another and have it boot normally. This would be epic! I've heard about HDD cloning software. But before I purchase and/or download this software, I need to know if i can just copy the OS over through the windows explorer

  Read the article

• Input/output error reading USB backup drive on CentOS 6.4

  - by Kev

  I'm suddenly seeing some strange behaviour on our USB backup drive that doesn't make sense to me: (2013-10-21 14:58:23 [root@newdc /]$ cd /mnt/backup/ (2013-10-21 14:59:03 [root@newdc backup]$ ls -la ls: reading directory .: Input/output error total 0 (2013-10-21 14:59:05 [root@newdc backup]$ df -h /mnt/backup Filesystem Size Used Avail Use% Mounted on /dev/sda1 917G 843G 28G 97% /mnt/backup How is it possible for the OS to know how much is in use, but I can't ls any of it as root? Or more to the point, what problem does this indicate? /var/log/messages said this: Oct 21 14:57:54 g5 kernel: EXT4-fs error (device sda1): ext4_journal_start_sb: Detected aborted journal Oct 21 14:57:54 g5 kernel: EXT4-fs (sda1): Remounting filesystem read-only But...read-only is something different than 'throw an io error'... After unmounting to try fsck on it, I had someone on-site look at it, and the drive was not spun up, and had a slow-flashing light, which I believe means it was in a power-suspend mode. So I had them unplug and replug the USB cable, and now (before remounting) it says: fsck from util-linux-ng 2.17.2 e2fsck 1.41.12 (17-May-2010) /dev/sda1: clean, 2805106/61046784 files, 181934167/244182016 blocks I then mount it and now ls works and df reports: Filesystem Size Used Avail Use% Mounted on /dev/sda1 917G 680G 191G 79% /mnt/backup What would cause it to go into such a state without being asked to? Why all the weird behaviour, and now it appears to not be corrupt?

  Read the article

• Terminal Server CPU usage at 100%

  - by Light1c3

  I'm running a terminal server with around 50-60 users,and every so often the server will go from 40% usage to 100%. I took a closer look an it seems every time this happens, a different user or two seem to be caught in a loop and end up using < 30% where the rest of the users only use a maximum of 5%. The company behind the software we use clame it's due to the servers inadequate hardware (It's a VM system running on a dual - quad core setup) which to me sounds like BS! I'm fairly new to this level of IT so if I misspoke I apologize. I have no way to prove it but I believe adding more raw hardware power wont do me any good as this to me seems like a bug in their software, and it will suck up as much ( or little) CPU as it's given. The VM in question has 4 vCPU cores and 12 GB RAM available, and is running Windows Server 2008, 64-bit Thanks in advance for your help! Note: I have the same question posted on SO, but was pointed in this direction so just in case, here is a link to the post http://stackoverflow.com/questions/17276602/termserver-cpu-at-100

  Read the article

• a disk read error occurred [closed]

  - by kellogs

  Hi, ¨a disk read error occurred¨ appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I can not recall how exactly have I used testdisk but it once said that ¨The harddisk /dev/sda (160GB / 149 GB) seems too small! (< 172GB / 157GB)¨ or something simillar. So far I have tried to ¨fixboot¨ and ¨chkdsk¨ from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please ? Thank you!

  Read the article

• Remotely port forward/launch process or a client-less remote desktop app?

  - by DC177E

  I have an XP box running Logmein at a remote location behind a linksys router, which was running well for a whole of four days, until we had a power failure. Our ISP gave us a new IP, the machine restarted, and logmein did not autorun (or, at least, it did not automatically sign in), and our service (which may or may not be a Minecraft server with non-backed-up save files) also did not run upon startup. Logmein does not register the new IP (it still displays the old one). I have a DDNS updater service, so I do know the new dynamic address. I have tried using the built in XP remote desktop service, but, as with almost all non-cloud-based remote desktop services, it requires a port forward. Thus, I would appreciate it if anyone has any ideas as to: A: Any way of accessing our router remotely to forward the remote desktop port. I've seen the Remote Management option (forwarding the setup page to port 8080), but I do not have it enabled. I've tried UPnP, but again, the setup page for our router is not forwarded. B: Any way of remotely launching a process that does not require port forwarding (or uses ports 255XX, 18XXX, or 9000.), such as a remote console service built into XP. I realize this is a near impossibility. C: A Way to remotely start logmein, and sign in, which is likely a definite impossibility. Sorry if this is too specific for Stackexchange, or if I've put it into the wrong section (is SuperUser the correct place for this?). Ideas would, again be much appreciated, as shot-in-the-dark-like this may be.

  Read the article

• Is my motherboard failing, or is there some other issue?

  - by ThatGuy

  So, several months ago I put together my own desktop PC. I set up a dual boot to Windows and Ubuntu. Recently, without changing any settings or installing anything new, the wifi stopped working on windows (I use a wifi adapter). It said it was connected, Network settings showed that it was working and running trouble shooting had no results. My internet still works on any other device. I found that removing the adapter from the motherboard and plugging it back in was the only thing that fixed the problem. Reinstalling the wifi drivers did not help. I purchased a new Wifi adapter, but the problem persists. More recently, I had a much more discouraging development. Sometimes, turning on the computer results in a boot loop: BIOS never starts. Instead, the monitor turns on as if it got a signal, then immediately turns off. This loops on it's own indefinitely until I hold down power, hard reset it, and try again. Sometimes it works, sometimes it doesn't. I haven't tested much on the Ubuntu side. It appears that wifi works at least some of the time, but since I've had issues just getting to BIOS I'm not confident the issue is on the software side. I've also noticed issues with some of the USB ports no longer working, but that seems to be off and on. Finally, as of a few minutes ago, I booted to windows to discover that everything was running very slowly. Slow here is a relative word, but I have a Samsung 840 pro SSD and I'm used to applications running nigh instantly, and it was a solid 3 minutes before any of my applications would load. Anyway, my question is this: Is it likely that my motherboard is failing? Either way, what steps can I take to try and pin down the problem and figure out what to do?

  Read the article

• WINDOWS: Your computer hangs. You can windows + R (run dialog) but performance is so halted taskMGR

  - by John Sullivan

  The question is, what process are available to try to recover from total system instability before pulling the plug when we can do nothing but programs or batches in the path from the run dialog (windows + r key), and performance is so dead that taskMGR / procEXP / other programs with visual guis are not usable? I am not a windows expert, but ideally someone out there has written a program that does more or less stuff like this: Immediately set (or perhaps I can set from the run prompt) its priority to extremely high, evaluate performance bottlenecks. E.g. is CPU 100%? If so identify offending program(s) or problems. Attempt / log fixes, then provide crude feedback asking the user if his performance has stabilized enough to abort, wait a few seconds, if no feedback continue, etc. etc. Eventually try to do any "system cleanup" if the program decides it cannot recover and perhaps finally provide a series of beeps to the user, or what have you, to say "OK, I give up, time to pull the plug". Ideally create a log, when able. These kinds of horrible hangs are a situation where surely trying something, anything, is better than nothing -- as long as that something is intelligent -- when the alternative is ripping out the power coord. Again, I am not a windows expert, so perhaps there is a much more elegant "hands on" approach I am not aware of.

  Read the article

• Windows 7: Dual Monitor Issue

  - by sdoca

  I have a Dell laptop with a docking station and two external monitors hooked up. I'm running Windows 7 64 bit. Originally, the two monitors were the same - Dell 1908FP. I have replaced one of them with an HP LA2405. I have set the HP 24" (1920 x 1200 connected via DVI port) as montior 1 and extended to use the Dell 19" (12080 x 1024 connected via VGA port) as monitor 2. I have set my power plan so that when the laptop is plugged in, it will turn the monitors off after 10 minutes, but it will not put my laptop to sleep. However, now that I have the HP monitor, when I unlock my laptop and the monitors come back on, all my windows are resized and shifted to the top left corner of the HP monitor as if they had been resized for display on the smaller Dell monitor. A co-worker has the exact same laptop and monitor configuration but doesn't experience this issue, so I figure there's some configuration that's different but we can't find it. I haven't been able to find any mention of a similar problem doing an internet search, but I'm not really sure what terms to use in my search. Anybody have any suggestions as to what may be causing the issue? OS setting? Monitor setting? EDIT: My laptop is using the Intel Graphics and Media Control Panel/drivers.

  Read the article

• Computer won't start up. Stuck on Lenovo splash screen. Help Diagnose

  - by Ace Legend

  I have some (I'm not sure exactly what model) Lenovo 21" IdeaCentre. Honestly, the computer works off and on. I have had problems with it not being able to shutdown, which I fixed. The fan seems to be constantly running, a few other problems as well. Anyway, nobody was using it when all of a sudden it switched to a blue screen. I was in the kitchen, but when I got over to the computer I read the message. It said something about bad drivers, but that is all I saw and then it restarted. However, when it got to the Lenovo Splash screen, nothing happened. I waited there for over 10 minutes, but still nothing. I tried to turn of the computer, but the only way to do it was to pull out the power cable. I then removed all USB devices and tried again. Still nothing. It also won't respond to keyboard input when I try to use enter to interrupt normal startup. My guess is some piece of hardware is damaged inside the machine. However, I have no idea what piece it is. Does anybody have any idea what could be wrong with it? Thanks.

  Read the article

• Chrome Lockups Windows 7 64-bit

  - by Mike Chess

  I'm running Google Chrome (6.0.427.0 dev) on Windows 7 Home Premium 64-bit (AMD Phenom 3.00 GHz, 8 GB RAM). The computer lockups hard after running Chrome for about five minutes. The lockup happens whether Chrome is actually being used to browse web sites or it is just idling. No programs can be started or interacted with when this happens. The computer must be power-cycled to recover. The lockup happens regardless of which web sites are being browsed. The system event logs do not show any events around the time when the lockup transpired. All other applications run just fine on this system. In fact, Chrome ran without issue for several months on this system (the system was brand new 03-2010). I also run the same version of Chrome on other computers (Windows XP SP3) without issue. I've come to really like Chrome and use it as my default browser whenever possible. What could be causing Chrome to cause the system to lockup as it does? Does Chrome have any logs that aren't part of the Windows event log? Does Chrome have a debug command line switch that might reveal more about what happens?

  Read the article

• PC in POST loop

  - by Antony Scott

  Hi, I have a custom built PC using a Gigabyte GA-EP35-DS3P motherboard with a Q6600 CPU. For the last 2 days it has got itself stuck into a POST loop. Saying that, I don't think it actually got in to the BIOS. It repeatedly lit up the LEDs and then not much more. Sometimes I could see the CPU fan twitch. Today I re-seated the DIMMs and it powered up straight away. Could this be a sign of an impending hardware failure? The PC is hooked up to a UPS, so I don't think it's a power spike or anything like that, as I have 2 other PCs on the same UPS and they're both fine. Yesterday, the first time this happened, I was getting a message which I think said "Scanning BIOS image on hard drive". I've been building and using PCs for well over 25 years and that's a new one on me! I don't think it's an over heating problem, as when the PC does finally boot up the CPU is running at 35-40C. Any help or suggestions would be greatly appreciated.

  Read the article

• Servers - Buying New vs Buying Second-hand

  - by Django Reinhardt

  We're currently in the process of adding additional servers to our website. We have a pretty simple topology planned: A Firewall/Router Server infront of a Web Application Server and Database Server. Here's a simple (and technically incorrect) diagram that I used in a previous question to illustrate what I mean: We're now wondering about the specs of our two new machines (the Web App and Firewall servers) and whether we can get away with buying a couple of old servers. (Note: Both machines will be running Windows Server 2008 R2.) We're not too concerned about our Firewall/Router server as we're pretty sure it won't be taxed too heavily, but we are interested in our Web App server. I realise that answering this type of question is really difficult without a ton of specifics on users, bandwidth, concurrent sessions, etc, etc., so I just want to focus on the general wisdom on buying old versus new. I had originally specced a new Dell PowerEdge R300 (1U Rack) for our company. In short, because we're going to be caching as much data as possible, I focussed on Processor Speed and Memory: Quad-Core Intel Xeon X3323 2.5Ghz (2x3M Cache) 1333Mhz FSB 16GB DDR2 667Mhz But when I was looking for a cheap second-hand machine for our Firewall/Router, I came across several machines that made our engineer ask a very reasonable question: If we stuck a boat load of RAM in this thing, wouldn't it do for the Web App Server and save us a ton of money in the process? For example, what about a second-hand machine with the following specs: 2x Dual-Core AMD Opteron 2218 2.6Ghz (2MB Cache) 1000Mhz HT 16GB DDR2 667Mhz Would it really be comparable with the more expensive (new) server above? Our engineer postulated that the reason companies upgrade their servers to newer processors is often because they want to reduce their power costs, and that a 2.6Ghz processor was still a 2.6Ghz processor, no matter when it was made. Benchmarks on various sites don't really support this theory, but I was wondering what server admin thought. Thanks for any advice.

  Read the article

• After RAID failure SBS 2008 issues logging in and Exchange store does not mount

  - by Josh R

  today has been one of those days. Yesterday a hard drive in our Dell Poweredge 2900 server failed and the RAID array didn't degrade gracefully, so I called Dell (Server still under warranty) and got an engineer to work though the RAID issues with me. He was a nice guy but didn't do too much. We tried to put the RAID in a state where it was bootable and even though we only lost one disk there are still issues with the server. Once we got the server to boot there was an error message saying that the logonui.exe was corrupted and we needed to run chkdsk. I clicked through the error messages and the login screen never came up. So I power cycled the server and it chkdsk automatically but the login screen didn't appear. I tried safe mode, no difference there either. So the issues I am currently having are: 1) The server boots up, the loading windows screen comes up then it dumps me into a black screen where I can only see my mouse cursor. Ctrl+Esc doesn't work Ctrl+Alt+Del doesn't work 2) Some of the services come up: DHCP, DNS, DFS, and Print come up 3) The exchange information store and transport service don't start - I tried using mmc to connect to services.msc on the computer and start them but they throw an error message of "Can't start because group or dependency failed" Has anyone had a problem like this? Can anyone offer some guidance? Thanks a bunch!

  Read the article

• after building in more ram, bios/debian does nothing [closed]

  - by derty

  My private server has 2x1gb Ram working with a 64bit Debian and an Q6600 Intel. This runs 2 virtual mashines on it each one recives 512mb RAM. Which you can immagine is a bit tight for the hole system. Now i got 2x2gb ram from a friend. I'm not sure if thery are clocking at the same speed, but i'm sure my power adaptor is not on his limit and can handle that. So there are 2 ram sockets left at the mainboard. I shuted down the system and build in the 4 gigs and looked what happen. After pressing the start button, everything gets noisy as known BUT the screen shows nothing, not even the bios stuff it usally does. Why isn't the system booting? I can immagine that it does not direkt link between booting debian and the bios not showing a thing. Or is it Grub? I mounted the system disk, and i can see it, switch folders write stuff with "vim" it does not seems like there is a problem.

  Read the article

• Sudden "No Signal" in HDMI-DVI connection

  - by nazikus

  Yesterday I have connected external display Asus VW192C to my laptop Dell XPS 14-L421X via HDMI-to-DVI-D cable. And it worked perfectly fine from start. The day after, Asus screen went blank showing "No signal". Every time I connection/disconnection cable or power off/on the display it says "No signal". And I didn't change any system configurations meanwhile. To troubleshoot the problem, I have tried to connect laptop to TV (hdmi-to-hdmi) - it was fine. I've tried to connect a different laptop to the display via the same cable - worked fine as well. So its obviously something on system level, either Windows or graphics drivers. Also it seems that Windows still see the external display (I can move mouse pointer away from the main screen in Extended mode), but there's just no signal. Any ideas? What else to try? PS. My laptop has 2 graphics cards - GeForce 630M and Intel HD 4000 using NVidia Optimus technology. I have updated to latest Intel and NVidia drivers, still didn't help. PPS. Although I shouldn't have updated (from Intel support): "our Intel generic graphics drivers from the Intel website do not support using both Intel Graphics 4000 and NVidia GeForece GT630M". Nevertheless, it should not affect connectivity to additional display.

  Read the article

• No audio with streaming video

  - by Chris Barnhill

  I am having trouble with audio when playing streaming videos. My sound card is fine. I know this because if I play sounds from my local machine, there's no problem. It's only when I try to play sounds from the internet that I lose audio. This only started happening recently when I did 2 things: I connected a USB headphone/microphone set to record screencasts I began recording/publishing screencasts from screenr.com. I have tried playing video both with the headset connected and without it connected: it makes no difference. If I record a screencast on screenr.com and preview it, I hear the audio. But once I publish is and play it, there is no audio. I also hear no audio with YouTube videos. I really hope someone can help. Thanks. The latest is that the problem went away after I powered my system off and on. A reboot didn't do it, I had to actually shut down the power.

  Read the article

• How to fix Windows 7 device removal notification loop

  - by Barry Kelly

  Bit of an odd one this. One of our PCs is getting caught in a loop some time after being turned on, usually after a USB storage device has been attached - sometimes an iPod, sometimes a GPS. Specifically, Windows Explorer starts showing a drive icon and letter (E:, as of right now) for the System partition (the small hidden one at the start of the boot drive). Then, the icon disappears. Then it reappears again. And disappears. It does this very quickly, at what looks like maybe 50 times a second. CPU usage in this loop is also very high; averages about 66%. This machine has an i7 920 CPU, which is quad core with hyperthreading; so this usage rate works out to about 5 100% busy threads, along with whatever normal idle load is (particularly Task Manager itself). Inspecting with Process Explorer shows that the device removal notification infrastructure has gone berserk. The threads in system service processes (i.e. apart from Windows Explorer) which are using all the CPU power relate to device notification. The Disk Management MMC snap-in also fails to run when the loop starts. The only way to break the loop, it seems, is to reboot the machine. Anyone seen anything similar to this, and know of a way to fix it? Machine details: Windows 7 x64, fully patched i7 920, 12GB RAM Intel SSD 80GB (X25-M, I believe; not G2) 2TB 5.2K disk for bulk storage AMD HD 5870 Further hardware details await. I'm going to go through and update all drivers I can find.

  Read the article

• Buying an old laser printer -- what will need to be replaced?

  - by marienbad

  Hi all -- as you can see I'm new. I do IT and wiring for a small local shop but I never deal with printers. I do a LOT of printing, and I'd like to stop spending as much money on it. On my local CL, there is an HP 8100DN (duplex network) printer for a very good price (and the toner is a quarter-cent per page). It has printed 200,000 pages and I don't yet know anything else about it. The model was released in 1999. So my questions: What are the parts that tend to need service on laser printers? On ebay, I see fusers, rollers, DC power boards, and motors. What would you expect to replace soon at 200,000 pages? Are there any good "tests" to find out if certain parts are near failure? Do you have anything to say about the HP 8100 specifically? The bottom line for me is that if there's any chance of repairs costing more than $100, it's not worth it for me.

  Read the article

• HP DL380 G3 2U For Basic Web Server in 2012

  - by ryandlf

  I have an opportunity to pick up a used HP DL380 G3 2U for $100. I'm looking for a basic entry level web server that I can host a small - medium size website on and more or less learn the ins and outs of running my own web server before I bite the bullet and spend a couple grand on a server. The specs are: Dual (2) Intel Xeon 2.4GHz 400MHz 512KB Cache 4GB PC2100 ECC Registered Memory 6 x 72GB 10K U320 SCSI Hard Drives Smart Array 5i RAID Controller Redundant Power Supplies DVD/Floppy, Dual Intel GB NIC's, USB Or would I be better off spending a couple hundred bucks on something like: this new HP Seems like the only major difference is SATA and a bit of storage, but I will likely be implementing a separate storage system of some sort anyways. I guess it also wouldn't hurt to mention that I plan on running a linux server distro, so would the hardware be likely to support linux with a system that is 4 generations old? I don't mind spending a couple hundred extra dollars if its a better solution, but as mentioned previously I am simple looking for a server to learn on and probably use for a year or so while I put together a small - medium size website.

  Read the article

• HP/IBM alternative to Buffalo iSCSI TerraStation?

  - by Robin Day

  I'm looking at virtualising some of our infrastructure in order to allow for more resiliance and future expandability. We have successfully virtualised on single servers with Direct Attached Storage and are now looking for a more future proof solution using a high powered host (or two) and a SAN (or two). I'm thinking that the host machine will probably be an HP ProLiant DL360 G7 (all of our exisiting infrastructure is HP). Unfortunately, I am new to the world of SANs. From what I can see, the Buffalo Terrastation III is all I would need in order to setup an iSCSI SAN for VMWare to use. However, I'm a little reticent to go that way as it's a bit too "entry level" for my liking. In particular I would be very keen for more redundancy, power, networking, etc. I'm also very aware that you "get what you pay for". Therefore, can anyone reccommend equivalents from the big boys? HP/IBM? I have searched high and low on the HP site and seen many options but am struggling to work out if it is all the hardware I will need. Some options appear to need separate controllers from disk enclosures, etc.

  Read the article

• Linksys SFE2000 Interface

  - by boburob

  I have a real problem with a layer 3 Linksys switch. First, every time it looses power, it seems to reset back to an older config. Not only this, but when this happens it looses interface settings on one subnet. This would not be a problem but I am completely unable to get to the interface on the working side. It allows me to log on and then just displays a blank screen. I have tried this on: IE6 IE7 IE8 IE9 Firefox 3.5 Opera Chrome All with the same results, except for Opera, which loads half the interface but nothing I can really use. I really need to get onto this switch so I can sort out routing and VLAN tagged ports, so if anyone has any ideas on either of these issues please let me know ASAP! Thanks! Also, due to its location and my lack of laptops with serial connections I cannot putty into it. UPDATE: Looked into this a bit more and it looks like this model of switch does not save the current config to boot unless you make sure to save it yourself, which explains the first issue, however the broken interface is more worrying!

  Read the article

• UEFI boot options gone

  - by user1797930

  I ran into some issues booting Windows after trying to make a complete backup of the disc. After searching for information about some of the error codes, I found advise to change some BIOS settings, but instead I thought I would just "restore defaults" to make sure all settings were set as originally intended. After doing so, all UEFI boot options except for "Windows Boot Manager" are gone. That means, including the CD/DVD drive, so I cannot even boot from a recovery DVD anymore - and as explained, Windows is not able to boot either. Do you have any advice? When I added a secondary drive originally, it was automatically added to the boot options menu. Even when removing and re-adding the drive physically, the option does not appear again. I have tried unplugging power, and hold down start button for 10 seconds, and boot afterwards - no change. It's a laptop so removing CMOS battery is not an option. I have read information that it is an issue with data removed from NVRAM, but I am unable to find a way to recover it. "Add new boot options" requires a path - but the CD/DVD was originally available without any CD's in the drive - so there is no path available to add the drive. I did try to open EFI shell, but it seems not to be embedded in the UEFI/BIOS. It just says "not found". I'm really lost here - any advice is appreciated.

  Read the article

< Previous Page | 190 191 192 193 194 195 196 197 198 199 200 201  | Next Page >