Search Results

Search found 11125 results on 445 pages for 'ip doh'.

Page 195/445 | < Previous Page | 191 192 193 194 195 196 197 198 199 200 201 202  | Next Page >

• How to block all multicast traffic travelling through a Cisco Catalyst 3750

  - by TrueDuality

  Something changed today. I can't seem to track down what, but one of our 3750s decided that it was going to forward all the multicast traffic it saw from the ghost server across every VLAN it has. I've tried writing a simple access group that consists of the following: access-list 100 deny ip any 224.0.0.10 0.0.0.255 access-list 100 permit ip any any I apparently mistakenly assumed that once applied to an interface that it would block all of the multicast traffic on that interface regardless of VLAN. I do not want any multicast traffic flowing through this particular switch to any VLAN or even to stay on the same VLAN beyond this switch. Does anyone have any ideas?

  Read the article

• Have two exchange servers to communicate together

  - by Data-Base

  We have Exchange Server 2007 using our domain ddd.com. We created an isolated network with a firewall/gateway and installed a DC and Exchange Server 2010 using a demo/test domain (ddd.loc). We opened all the needed ports in the firewall (10.10.2.88) to the Exchange Server 2010. In our main Domain Controller (10.10.2.3) we defined the domain ddd.loc with IP 10.10.2.88 (firewalls). We also we defined MX records to the same IP (10.10.2.88) We did that so when we send email from my email [email protected] it will go to the Exchange Server 2010. Anyways, all the pings test from to any servers are OK. But we are not able to send or receive emails. Between these Exchange Servers we can not send any email from the 2010 to any email in general (emails are pending). Also, in Exchange 2007 we are getting error #550 5.1.1 RESOLVER.ADR.RecipNotFound; not found ##

  Read the article

• NAT and NGINX on the same server

  - by Morten

  I'm setting up a VPC cluster for my collaborative todo list application www.getdoneapp.com. To have my servers on the private network I need a NAT server so my servers on the private network can connect to the internet to receive updates and what not. The NAT server will consume an elastic IP address, so I'm wondering if I can just have that NAT server run nginx to direct traffic to my internal servers for HTTP. So the question is, is it a bad idea to run NGINX and NAT on the same server, or should I go for consuming 2 elastic IP addresses?

  Read the article

• What's a good tool for checking from my own machine that my server is up?

  - by chico

  I'm looking for a good tool (web site or not) that I can use to do a simple check whether my web server is accessible from outside LAN (it's serving in a non-standard port). To give some context, I've gone through this problem: can't access my ip from outside. Even the tools I've found are not really working. Currently to fetch the html I serve with the online bash tool I do: curl <my ip>:<my port> \ | sed 's/&/\&amp;/g; s/</\&lt;/g; s/>/\&gt;/g; s/"/\&quot;/g; s/'"'"'/\&#39;/g' I'm looking for a simple tool that can display the html properly, or just show raw text without resorting to sed html escaping and curl.

  Read the article

• Use teamviewer for running web server [closed]

  - by Steve

  I have a PC behind NAT. I want to host a web server on it which is accessible from the internet. I cannot open any blocked ports nor do i have admin rights on the computer. But it has a teamviewer client running on it 24*7 to which i do have access(no vpn installed). I can accesss this client from anywhere using teamviewer. I want to know if somehow i can use teamviewer to get a ip/hostname that is accessible from the internet and host a webserver. Also is it possible to get an ip if i get admin access but without opening ports.

  Read the article

• hMailServer Email + MX Records Configuration

  - by asn187

  Trying to make DNS changes to enable email to be sent using hMailServer. My mail server is on a separate machine with a separate IP Address. I have already added MyDomain.com and an email account I have create a MX Record with the mail server being mail.domain.com an a priority on 20. 1) But the question is how do I now link this MX record for the domain to my mail server/ mail server IP Address? 2) What changes are needed in hMailServer to complete the process and be able to send emails for the domain? 3) In Settings SMTP Delivery of email: What should my configuration here look like?

  Read the article

• MMS gets hostname from uname and can't connect to it

  - by Adam Monsen

  I'm trying to get 10gen's MongoDB Monitoring Service monitoring my 3-node replica set. The replica set running in an AWS VPC. Each node runs on a different [virtual] machine. Assume their IPs are 192.168.1.1 (primary or secondary), 192.168.1.2 (primary or secondary), 192.168.1.3 (arbiter). From a quick look at the source, MMS appears to get the hostname of the machine it is running on like so: platform.uname()[1] For my VPC EC2 instance, this returns something like ip-192-168-1-1 MMS then tries to connect to this hostname, which does not resolve. I'd rather just use IP addresses (since they're always static), but it seems like the hardcoded use of platform.uname()[1] in mmsAgent.py precludes that. So, what's an elegant way out of this? Hack /etc/hosts? I'm not setting up a DNS server just for this. Maybe I'm just misunderstanding how to configure MMS.

  Read the article

• Windows 2003 - RAS service - VPN client can only connect to server, not internal network

  - by Gk

  Here is my diagram http://imageshack.us/photo/my-images/263/vpnt.png/ Server has two NIC: One connect to Internet, one connect to internal network. RAS service is configured with static IP pool on the same subnet of internal network (10.10.0.x). The problem is when a client connect to server, client can connect to server(10.10.0.10), but cannot connect to another host locate in internal network (10.10.0.11) even cannot ping to 10.10.0.50. RAS configured with IP routing enabled, client connect with options: Use default gateway on remote network. I'm messed up and can not figure out what wrong. Please help me T_T. TIA, giobuon

  Read the article

• How do I route traffic to website using a spcified network connection on Windows 7

  - by rwetzeler

  I want to route all traffic to a website over my wireless connection while the rest of the traffic using my lan. What I tried was first finding out the IP address of the website I want to go to. For example, lets say pandora.com. I found it resolves to 208.85.40.20. I have entered that entry into my hosts file. I then added that route using route add 208.85.40.20 mask 255.255.255.255 WirelessIP. It doesn't seem to work however. Instead of using the IP address, is there a way that I can just say.. this URL to route over that connection? Does anyone know of a program that I can install that will do this.. possibly some sort of proxy or a software load balancer that can do this?

  Read the article

• Can I create a virtual network interface to connect to a real network device?

  - by michelemarcon

  I have a networked windows pc with 2 network interfaces. The first connects to a lan with ip address 10.1.. The second connects to another lan with ip address 10.2.. Maybe it's a dumb question, however is it possible to virtualize the second network interface, so that the pc can connect to the 2 lans? If necessary, I may switch to linux or paravirtualization. CLARIFICATION: I want to send DHCP broadcast packets on the second lan, but not on the first lan. I want to do it with one single physical network interface. At the moment, I'm not using any virtualization software.

  Read the article

• Remotedesktop to windows 2008 server with 2 nics

  - by The_Mo

  Hi I have 2 NICs on a Windows 2008 R2 Server. nic1 with ip address 192.168.2.1 with gatewaty 192.168.2.254 and nic2 with ip address 10.96.6.253 with no gateway. The windows 2008 server is connected to a router which is connnected to another router so if I want to connect to the windows 2008 server I use 192.168.0.31 because it is forwarded. If I use remote desktop to connect to that machine I use 192.168.0.31 and that works well, but the server has a seccond nic and I want to be able to connect with a remotedesktop to nic2. Any help appreciated! [server windows 2008 r2 192.168.2.1] -- [router 192.168.2.254/192.168.0.31] -- [my computer 192.168.0.13 gateway 192.168.0.254]

  Read the article

• Subdomains, folders, internationalization, and hosting solutions

  - by justinbach

  I'm a web developer and I recently landed a gig to develop the US / international version of a site for a company that's big in Europe but hasn't done much expansion into the US yet. They've got an existing site at company.com, which should remain visible to European customers after the new site goes up, and an existing (not great) site at company.us, which I'm going to be redeveloping (the .us site will be taken down when my version goes up--keep reading for details). My solution needs to take into account the fact that there are going to be new, localized versions of the site in the fairly near future, so the framework I'm writing needs to be able to handle localizations fairly easily (dynamically load language packs, etc). The tricky thing is the European branch of the company manages the .com site hosting (IIS-based) and the DNS, while I'll be managing the US hosting (and future localizations), which will likely be apache-based. I've never been a big fan of the ".us" TLD--I think most US users are accustomed to visiting the .com--so the thought is that the European branch will detect the IP of inbound traffic and redirect all US-based addresses to us.example.com (or whatever the appropriate localized subdomain might be), which would point to the IP address of my host. I'd then serve the appropriate locale-specific content by pulling the subdomain from the $_SERVER superglobal (assuming PHP). I couldn't find any examples of international organizations that take a subdomain-based approach for localization, but I'm not sure I have any other options as a result of the unique hosting structure here (in that there's not a unified hosting solution for the European and US sites). In my experience, the US version of an international site would live at domain.com/us, not at us.domain.com, and I'd imagine that this has to do with SEO (subdomains are treated as separate sites, so improved rankings for the US site wouldn't help the Canadian version if subdomains are used to differentiate between them). My question is: is there a better approach to solving this problem than the one I'm taking? Ideally, I'd like to use a folder-based approach (see adidas.com as an example of what I'm talking about), but I'm not sure that's a possibility given that the US site (and other localizations) will not be hosted on the same server as the rest of the .com. Can you, in IIS, map a folder (e.g. domain.com/us) to a different IP address? What would you recommend? Thanks for your consideration.

  Read the article

• Config deployment on multiple servers.

  - by user66601

  I have multiple servers in WEB cluster (identical configuration for all of them, despite the IP) How do you deploy changes in configs on multile servers? I make the new config, then create config per every server (placing correct IP), and next: upload them on every server, replacing old ones (rsync over ssh) set on every server a job which reloads webserver at the same time (servers use ntp). - this done by issuing commands by script (to save time for logging in) before adding a job for server reload - there's checksum test of the config on the server) - an a notification in case of fail How do you see such method? What should be the "professional way :) ? (I don't say my way doesn't work... it works and saves my time not used for logging on every webserver.) Regards,

  Read the article

• Network Services disabled (not starting) on Windows XP

  - by Rickesh John

  I am currently running Windows XP Service Pack 3 on my system. But today, when I failed to connect to the internet, via a LAN cable, I realized that almost all of the vital network services had stopped functioning. Any attempts to start it through services.msc gives me the following message: Could not start the DNS Client Service on Local Computer Error 1068: The dependency service group failed to start All my software or services that are related to networking have stopped functioning, for example, Windows Firewall is turned off permanently, so is my Avast Anti-Virus' service of Real Time Shields and Web Shield. When I insert the LAN wire into my laptop, it registers itself, but this is what I get when I do a ping localhost C:>ping localhost Unable to contact IP driver, error code 2 Moveover, with ipconfig I get this : Windows IP Configuration An internal error occurred: The request is not supported. Please contact Microsoft Product Support Services for further help. Additional Information: Unable to query host name On some further poking around, I saw that none of the "NETWORK SERVICE" process in task manager, except svchost.exe were running. Also, when I first opened the task manager, I saw some 20 processes running with username column empty for most of them. With some search in Google, I found out that these services were important, DHCP DNS Net logon Network connection Network location Awareness TCP/IP Net BIOS Helper none of them, except Network Connections are working, they do not start. The event viewer of my system shows a bunch of 7000 and 7001 event errors. I have tried re installing the network driver, booting in safe mode with networking and tried to enable those services mentioned above. I had disabled System Restore some time back, so I have no restore points for my system. I tried a lot of things from Google searches but none of them worked. Also, with such a long list of issue, I am a little confused as to what should I search on the internet. :( One more thing I would like to mention, previous morning, my anti-virus Avast detected a RootKit buried deep in my system folders. It was removed, but maybe this was a problem caused by the root kit. I did run a boot-time scan but no viruses were found. Please please please advice. Is formatting and re-installation of Windows my only option?

  Read the article

• How to redirect domain to new server?

  - by hfidgen

  I've got a domain registered with a hosting company who I no longer wish to use. I'm happy for them to keep managing my domain, but I want my domain to point to my new (better) server which i've just bought and set up. I know my new server's IP address and Nameservers, What do I need to do in my domain management control panel to make it point to my new server? Change the "A" record to the new IP? Change the nameservers to my new hosts nameservers? Is that it? Are there no other record on either server which need changing? I always get confused by who needs to do what when it comes to domains... Thanks, Hugh

  Read the article

• Ping myself, works with ipv6 not ipv4 in Windows 7

  - by user68546

  Hi! I've tried to solve the following problem with no luck and I need some proffesional help. The following is possible: Ping all computers (that I tried) in the domain without problem. Ping myself with localhost which use ::1. Ping myself with my given ipv6 IP. Internet access. The following is not possible: Noone can ping me (request timeout) with computername/ipv4/ipv6. I cannot ping myself with my given ipv4 IP or 127.0.0.1 (request timeout). Tried to enable/disable TCP/IPv4. Same issue. Turned off windows firewall. Added an inbound rule to allow icmp (just in case). Same same.. Is there someone out there that has any idea what the issue could be? Any help would be most appreciated!

  Read the article

• How to make local apache server public/visible ?

  - by George

  Hello. I am running an Apache2 server on a Fedora 13. I'd like to make it publicly accessible(visible).For example I'd like when somebody types http://my.ip.numbes/ that they would see what I have in my document root folder. Just for a presentation of a course work at university. Permissions are set to 755. User owning the document root is apache. SELinux is temporarily disabled. But port 80 is closed. I tried to open it by adding an entry to iptables and restarting them, no change. I guess I am missing something big here. Help would be greatly appreciated. Note: I have a static (public, real) IP address.

  Read the article

• Share the same subnet between Internal network and VPN Clients

  - by Pascal

  I would like to set up a configuration where VPN clients connecting to my Forefront TMG can access all the resources of my Internal network without having the to use the option "Use default gateway on remote network" on the VPN's TCP/IP Ipv4 Advanced Settings. This is important to me, since they can use their own internet while accessing my network through VPN (the security implications of this are acceptable on my cenario) My Internal network runs on 10.50.75.x, and I set up Forefront TMG to relay the DHCP of my Internal network to the VPN clients, so they get IPs from the same range as the Internal network. This setup initially works, and the VPN clients use their own internet, and can access anything that is on the internal network. However, after a while, HTTP Proxy Traffic from the Internal network starts getting routed to the IP of the RRAS Dial In Interface, instead of the IP of the Internal's network gateway. When this happens, the HTTP Proxy starts getting denied for obvious reasons. My first question is: does this happen because Forefront TMG wasn't designed to handle a cenario that I described above, and it "loses itself"? My second question is: Is there any way to solve this problem, either through configuration or firewall policies? My third question is: If there's no way that it can work with the cenario above, is there another cenario that will solve my problem, and do what I'd like it to do properly? Below are my network routes: 1 => Local Host Access => Route => Local Host => All Networks 2 => VPN Clients to Internal Network => Route => VPN Clients => Internal 3 => Internet Access => NAT => Internal, Perimeter, VPN Clients => External 4 => Internal to Perimeter => Route => Internal, VPN Clients => Perimeter Tks!

  Read the article

• FTP server questions

  - by Brad

  I'm currently trying to set up a home FTP server using debian and proftpd and I've run into a problem that has me confused. I have most things set up already, I believe, but I cannot access my ftp server using my external ip. I've forwarded the correct port on my router and I've checked http://www.yougetsignal.com/tools/open-ports/ to be sure that it is, in fact, opened. I've used telnet locally on my server to check that the port accepts connections. I am able to use ftp via LAN. But, I still cannot access anything externally. I'm thinking that there's still some router configuration to be done in order to fix this, such as routing all connections on my ftp port to my server via the internal ip, but I can't find any option on my router to do this. Is this a necessary step? There is an option to use DMZ hosting, but I'd rather avoid it if possible. I can provide additional information as requested, please let me know any information that you think could help at all. Thanks. -Brad PS - I have a Telus Actiontec Modem/Router Update - !! Trying my ftp server out at work, worked! I guess I did set it up correctly after all. What is confusing me, though, is why doesn't the server allow me to connect locally anymore? That seems very weird to me. Also, I don't really understand why I am denied outright if I attempt to connect from the same network using the external address. I'll look into it more when I get home, but thank you guys for your help. Update 2 - I found the problem with not being able to connect locally anymore. I was setting the masquerade address to my external IP and for some reason that was causing it to hang on MLSD when I connected using my LAN address. I've removed the masquerade address and I'm going to check if I need it at work tomorrow. I'll update this page if I find anything.

  Read the article

• ubuntu server in a vm, can't connect to internet

  - by jessh

  I'm attemtping to host my own development web server in a virtual box guest, Ubuntu Server. I would like this virtual machine to be accessible from not only my home network, but outside the LAN as well. As such, I've set up a static IP (so I can later forward ports to this static IP.) My virtual box settings have this vm only using one adapter -- in bridged mode. Here's what my /etc/network/interfaces looks like: iface eth0 inet static address 10.0.1.203 /*this is outside the DHCP range*/ netmask 255.255.255.0 gateway 10.0.1.1 network 10.0.1.0 broadcast 10.0.1.255 dns-nameservers: 8.8.8.8 8.8.8.4 Here's what the output of ifconfig looks like: https://dl.dropbox.com/u/2241201/locker/ubuntu.png My Host is a mac mini, running OS X 10.7. From within the guest, if I ping google.com: $ ping google.com # outputs 'ping: unknown host google.com' immediately Why am I unable to access the web?

  Read the article

• Setting up Mac VPN on simple network with separate IPs

  - by Dave

  Hi there, We have a pretty simple network configuration. A typical ASDL line with two extra IP addresses. We have a basic home network router Dlink DIR-655. We have two Mac OS X Snow Leopard Servers that we want to setup VPN on. The problem is that we can't change the ports which VPN works under ie. we can only setup port forwarding for UDP 500,1701,4500 to a single server. I'm wondering how we can cost effectively re-work our network so that we can take advantage of the separate IP addresses and have both VPNs working with the same router. Is that possible with our current hardware setup or do we need something more powerful? We're also toying with Mobile Access and wondering if that might be easier to setup. Expert help is greatly appreciated.

  Read the article

• If I don't want subdomains to send out email, do I need SPF records for them?

  - by Phil

  I have a main domain with (now) valid SPF record, but we also programmatically create lots and lots of subdomains for clients via cpanel PHPXML API. These subdomains are not intended to send any mail. When we create them, they are getting an A record of my ip, and a TXT record of "v=spf1 +a +mx +ip4:[MY IP] ?all". Those are all the DNS records they have Recently we have had a lot of email spoofing and realized there was an invalid (duplicate SPF) for our main domain. We just fixed that, but are unsure if: 1) Can spammers still spoof email from subdomains without MX records, with above current listed SPF? 2) Is it better to have no SPF for subdomains than the one I have listed? 3) Is there a way to prevent subdomains from sending/spoofing email via my main domain's SPF? Here is the main domain SPF that our host suggested we switch to: "v=spf1 a mx ptr a:dedrelay.[webhost].com include:dedrelay.[webhost].com ~all"

  Read the article

• How to use CLEAR USB WiMax in Ubuntu (host) and Windows XP (guest) using VirtualBox

  - by bithacker

  I'm trying to use CLEAR Motorola WiMax USB in Ubuntu as there is no support for Linux as yet. I've installed Windows XP as guest in Ubuntu and the version I'm using is 3.2.2. USB is connecting fine in Windows XP but I can't use internet in Ubuntu. Can you please tell me how to do it. Here is the configuration that could help you guys. Thanks in advance. I'm using Two Network Adapters. Network Adapter 1: PCnet-FAST III (NAT) Adapter 2: PCnet-FAST III (Host-only adapter, 'vboxnet0') ipconfig [on Guest windowsXP] Windows IP Configuration Ethernet adapter Local Area Connection: PCnet-FAST III (NAT) Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.0.2.15 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 10.0.2.2 Ethernet adapter Local Area Connection 3: PCnet-FAST III (Host-only adapter, 'vboxnet0') Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.56.101 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter Local Area Connection 2: Connection-specific DNS Suffix . : CLEAR Motorola USB IP Address. . . . . . . . . . . . : 10.168.242.33 Subnet Mask . . . . . . . . . . . : 255.255.192.0 Default Gateway . . . . . . . . . : 10.168.192.2 IFCONFIG [on Host Ubuntu] (Ethernet) eth0 Link encap:Ethernet HWaddr 00:14:22:b9:9d:76 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 eth1 (Wireless) Link encap:Ethernet HWaddr 00:13:ce:f0:9b:0d inet6 addr: fe80::213:ceff:fef0:9b0d/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:1 errors:0 dropped:5 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:84 (84.0 B) Interrupt:17 Base address:0xe000 Memory:dfcff000-dfcfffff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2292 errors:0 dropped:0 overruns:0 frame:0 TX packets:2292 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:171952 (171.9 KB) TX bytes:171952 (171.9 KB) vboxnet0 Link encap:Ethernet HWaddr 0a:00:27:00:00:00 inet addr:192.168.56.1 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::800:27ff:fe00:0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:137 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:21174 (21.1 KB)

  Read the article

• How can I port forward over a VPN NAT?

  - by Charlie

  I have a multi-site VPN currently running with pfSense boxes and currently using OpenVPN. However I can change the OS and VPN type if need be. The main router has a 10.13.0.0/16 subnet and a series of public IPs For example, a branch has a 10.12.1.0/24 subnet How can I port forward NAT traffic on a public IP of the main router to a server behind the NAT of the second? So for instance port 95 on a public IP assigned to the main router forwards to 10.12.1.102 on the other router. Is this even possible? Currently my setup works great but only for intertnal traffic

  Read the article

• Problems bringing up a second virtual network interface

  - by tubaguy50035

  I'm having issues adding a second IP address to one interface. Below is my /etc/networking/interfaces # The loopback network interface auto lo iface lo inet loopback #eth0 is our main IP address auto eth0 iface eth0 inet static address 198.58.103.* netmask 255.255.255.0 gateway 198.58.103.1 #eth0:0 is our private address auto eth0:0 iface eth0:0 inet static address 192.168.129.134 netmask 255.255.128.0 #eth0:1 is for www.site.com auto eth0:1 iface eth0:1 inet static address 198.58.104.* netmask 255.255.255.0 gateway 198.58.104.1 When I run /etc/init.d/networking restart, I get a fail error about bringing up eth0:1: RTNETLINK answers: File exists Failed to bring up eth0:1. Any reason this would be? I didn't have any problems with I first set up eth0 and eth0:0.

  Read the article

< Previous Page | 191 192 193 194 195 196 197 198 199 200 201 202  | Next Page >