Search Results

Search found 29567 results on 1183 pages for 'network tools'.

Page 195/1183 | < Previous Page | 191 192 193 194 195 196 197 198 199 200 201 202  | Next Page >

  • How to Set "<options>" in fstab - Manual Mounting is Successfull

    - by nicorellius
    I am not real familiar with fstab yet, so I have a couple questions. When I use this command to mount devices: sudo mount -t cifs -o username=admin //192.168.1.134/share_name /mnt/share_name With passwords: sudo="local user password" password="password for device" How do I translate that into an fstab entry? So far, I have tried this in the fstab and mounting fails: //192.168.1.134/share_name /mnt/share_name cifs default 0 0 This is where the question comes in. Where I have default, should there be something instead, indicating username=admin, etc?

    Read the article

  • Best way to split LAN computers on two WANs (not load balancing)

    - by lpfavreau
    What is the best way to split the computers of a LAN (about 50 computers) to go on two WANs, depending on the computers' IP address or computers' configuration (gateway). I'm not looking for load-balancing, I need to be able to route which computer uses which Internet connection. A solution would be to rewire the old office to split the two distinct groups that need to use two different Internet connections but I'm not sure it's worth it at the moment. I have a pfSense router configured with the LAN (DHCP), WAN1 and WAN2. I also have the IP addresses (and ability to configure) the next router on WAN1 and the one on WAN2. What would you suggest? Routing based on IP addresses ranges? Different gateways? VLANs would be difficult for the same reason as to why rewire is a bit complicated. Thanks!

    Read the article

  • Distributed Nagios Installation

    - by kruczkowski
    I'm looking for a plug-in or product that will act as a remote probe and perform tests then send back the results to the central Nagios server. Reason for this is that I'd like to monitor internal systems and servers at customers, but don't want to allow all the traffic passing the firewalls. Ideally I'd like a soft-probe that would be installed and then perform the tests and send back the results (via SSH) to the central Nagios installation. Does anyone know of a product or plug-in that would offer such service? If not Nagios, is there any other monitoring system that does such a thing (ideally open-source)?

    Read the article

  • Connect 2 ubuntu computers into a LAN

    - by arsan
    I've got two computers both running Ubuntu and i want to connect them into a LAN so i can ssh from the one into the another - i know how to do the ssh configuration part, i just don't know how to connect them - i put the cable but nothing happened. Please tell me what needs to be done.

    Read the article

  • Have to reset wireless frequently on iPad / Macs connected to Cisco WRV200

    - by retailevolved
    I have a Cisco WRV200 set up in our small office. The wireless signal works great for PCs, but I have found that Macs and iPads have to frequently reset the connection. It will be working for about 10 minutes, then stop. To fix it, I just turn off Airport and turn it on again. On an iPad, I have to go into settings, shut the wireless off, and then turn it on again. The router is broadcasting mixed B/G on channel 6. Security is WPA-PSK2. Anybody out there had similar issues with their router? How can I fix it?

    Read the article

  • How to see the properties of a DOM element as they change in realtime?

    - by allquixotic
    JavaScript code can update the properties/attributes of DOM elements in real time by responding to events and so on. Here is an example. In the table on that page, move your mouse over the cells. Notice how they change color when the mouse is on them, and the color goes away when you move the mouse to another cell. Now, using Firefox or Chrome (but not IE, Opera, etc.), I want to examine the background color, expressed in RGB or hex or whatever, of the cells updated in real time, as the mouse cursor enters and leaves the region and causes the JS to do its thing. The behavior that I observe, currently, is that the Inspect Element functionality of both Firefox and Chrome does not update the value of the properties as they are updated by JavaScript. So, in order to view the latest value of the property, I have to inspect the element again, and it takes a momentary "snapshot" of the values. But since the values only change while I have the mouse on them, I can't take a snapshot of the value I want while my mouse cursor is over the cell, because I have to remove my mouse from the cell to select the "Inspect Element" item in the right-click list! If it is possible to have the values updated in real time using either Firefox or Chrome, or an extension, on any recent version of the software (up to the latest stable), please provide instructions for doing so.

    Read the article

  • How to disable shared folders passowrd prompt on window & Linux

    - by user53864
    I'm using windows xp, vista, server 2008 R2, ubuntu-linux 9.10, 9.04, 8.10 desktop editions. I shared some folders/directories in windows and in ubuntu machines. Normally for the first time it's prompted for the password when tried to access the shared folders on either of the machine and again they prompt for the password when the system is rebooted. Recently I've created a batch and sh script which copies from the shared folders from windows to ubuntu and vice-versa. But the scripts cannot automate the password prompt and I'm wondering if I could disable the password prompt of the shared folders on windows and as well as on ubuntu machines so that my script runs smoothly. I don't know if it's possible or not but want to confirm posting here and if it is then nothing but saying need help...!. Thanks all!

    Read the article

  • Fast extraction of a time range from syslog logfile?

    - by mike
    I've got a logfile in the standard syslog format. It looks like this, except with hundreds of lines per second: Jan 11 07:48:46 blahblahblah... Jan 11 07:49:00 blahblahblah... Jan 11 07:50:13 blahblahblah... Jan 11 07:51:22 blahblahblah... Jan 11 07:58:04 blahblahblah... It doesn't roll at exactly midnight, but it'll never have more than two days in it. I often have to extract a timeslice from this file. I'd like to write a general-purpose script for this, that I can call like: $ timegrep 22:30-02:00 /logs/something.log ...and have it pull out the lines from 22:30, onward across the midnight boundary, until 2am the next day. There are a few caveats: I don't want to have to bother typing the date(s) on the command line, just the times. The program should be smart enough to figure them out. The log date format doesn't include the year, so it should guess based on the current year, but nonetheless do the right thing around New Year's Day. I want it to be fast -- it should use the fact that the lines are in order to seek around in the file and use a binary search. Before I spend a bunch of time writing this, does it already exist?

    Read the article

  • What's port 1283?

    - by kbluck
    I see a lot of connection attempts to 1283/tcp on my firewall from a client computer to a Windows Server 2008 Domain Controller. What exactly is this traffic? Something to do with NetBIOS, perhaps?

    Read the article

  • Browsing \\computer\share fails, but net use \\computer\share works?

    - by JMD
    I've had mixed results with using Windows Explorer to browse remote file shares. The setup: I'm at work on Windows XP SP3 Files are at home on Windows XP SP3 Two separate VPNs are available to access my PC at home corporate OpenVPN (10.1.2.3) a Hamachi/LogMeIn connection (5.1.2.3) With respect to my problem, it doesn't matter which IP I use. They both perform exactly the same way: I expect that if I open Windows Explorer and type in \\10.1.2.3\Shared I should be interrupted with a challenge for credentials, and then be able to interact with the files in the share. However, I just get that annoying dialog, "Windows cannot find '\10.1.2.3\Shared' Check the spelling and try again, or try searching for the item ..." However, I can take that exact same computername/sharename and with net use I can: net use * \\10.1.2.3\Shared * /user:homecomputername\username with this result: Type the password for \\5.69.83.158\C$: Drive Z: is now connected to \\5.69.83.158\C$. The command completed successfully. I can then access the files in Z: in Windows Explorer which was my original intent. Even after Z: is already mapped and the credentials are cached I still cannot bring up \\10.1.2.3\Shared in Windows Explorer. Why does the latter work, but not the former? Edit: Other services work fine, such as RDP. (I have a problem in which I can't SSH home, but I'll consider that separately.)

    Read the article

  • How do I associate server traffic to a domain hosted on that server?

    - by morley
    I have three or four Linux servers, each of which hosts anywhere from 5 to 50 domains. Each domain has its own folder: /www/projectname/web/ Logs go in: /www/projectname/log However, if there's a traffic spike (or, as I see it on my end, a memory usage spike), I'm not sure how to figure out which domain is responsible for the traffic without running tail -f on each of the projects and making an educated guess based on how fast things scroll. There's got to be a better way! There probably is, but I haven't seen it. And the last time I checked, bandwidth monitors only report system-wide load. So if anyone knows how to do this the right way, please let me know. Thanks!

    Read the article

  • Common filesystem for servers behind a rackspace load balancer

    - by thanos panousis
    Our PHP application consists of a single web server that will receive files from clients and perform a CPU-intensive analysis on them. Right now, analysis of a single user upload can take 3sec to conclude and take 100% CPU. This makes our system capacity amount to 1/3 requests per second. My team's requirement is to increase capacity without a lot of code reengineering. A possible solution would be to set up a load balancer in front of multiple servers running the same app, connecting to a common DB. The problem is that the analysis outputs files on disk. A load balancer would increase capacity, but then files won't be available between servers so consequent client requests may fail. We are hosted on Rackspace, is there a way to configure some sort of "common" storage for all servers, without having to rewrite our file persistance code? Current code relies on simple fopens etc. What are our options?

    Read the article

  • How to repeat a POST request using Chrome's developer tools?

    - by Luke The Obscure
    Not sure if this is the right stack exchange to ask this, but here goes... I'm trying to wean myself off of Firebug, which has served me very well for a lot of years. One feature that seems to be missing in Chrome's dev tools is the ability to repeat an AJAX POST. In firebug I can right click on the request in the console and hit "Open in new tab" and the request is repeated exactly as it was originally sent. In Chrome, the same action just does a normal GET on the link, without any of the post data. Is there any way to repeat an AJAX POST in Chrome's dev tools?

    Read the article

  • How to logon to a non-domain computer from one in a domain

    - by Svish
    I've met a rather annoying problem that should be very simple, but I can't seem to figure it out. I have a work laptop that is part of a domain, so my username is foobar\bob. I also have my home computer with no domain, just the username bob. I'm trying to connect to a share on my home computer from my work computer. It's asking me for my username and password, which is bob, but when I type in bob it assumes I mean foobar\bob, which of course doesn't work. I've tried to use hostname\bob, but that doesn't seem to work either... What can I do here? Both computers are running Windows 7.

    Read the article

  • Notification if SyncToy fails

    - by Joel Coehoorn
    I support a number of laptop users. In the past (before there were many laptops), each user's computer was set up so that their My Documents folder was mapped to a shared folder on the server. This worked very well for desktops, but has several obvious downsides for laptops (no files when you're off-site, etc). I'm exploring several alternatives for laptops to better map the shared drives, and SyncToy seems the best so far. I have a couple trial users set up so that it syncs automatically whenever they log in, along with a desktop icon they can click if they know they'll need something saved before the next login. My problem is that I'm concerned how I, as the maintainer of this system, can spot failures. I don't want my first indication of a problem to come after a user drops their laptop in a lake and it turns out nothing was synced for the last year. Any ideas?

    Read the article

  • port forwarding/network settings preventing from game hosting

    - by Xitcod13
    I asked where to post this question on stackoverflow meta and they directed me here. Im on wireless connection and I want to host games in StarCraft: Brood War and i've been looking everywhere on how to accomplish that. My internet is amazingly fast so its not an internet problem (and when i play other peoples games dont experience lag) I found out that i need to have a static IP but I have already checked that i do (i downloaded a program to make my id static and it already was; The program asked for which router I used So i think it checked the router settings already) I found out that i need to allow Sc access through the firewall which i already did (i have zone-alarm but I allowed it everything possible except receiving emails lol) I have recently noticed that few people actually can join my games but most of them cannot. I dont know whats going on here. I really want to be able to host games overall how do I go about checking what is wrong with the network. Update: Alright I figured out what i did wrong in the first part I did not actually set up forwarding on the router -.- I have tried to fix my mistake. I went to forwarding options in my router (as this guide for my specific router suggests) but when i click ok I get a message incorrect ip address. 192.168.1.1 is my routers address. The default address that appears there is 192.168.1 (blank) I have set it to my computers current Ip4 adress which 192.168.1.23 I hope this works If so i will post it as an answer and mark it.

    Read the article

  • Windows VPN always disconnects after < 3 minutes, only from my network

    - by hemp
    First, this problem has existed for almost two years. Until serverfault was born, I pretty much gave up on solving it - but now, hope is reborn! I've set up a Windows 2003 server as a domain controller and VPN server at a remote office. I am able to connect to and work over the VPN from every windows client I've tried, including XP, Vista, and Windows 7 without issue, from at least five different networks (corporate and home, domain and non.) It works fine from all of them. However, whenever I connect from clients on my home network, the connection drops (silently) after 3 minutes or less. After a short while, it will eventually tell me the connection has dropped and attempt to redial/reconnect (if I've configured the client that way.) If I reconnect, the connection will re-establish and appear to work correctly, but again will silently drop, this time after a seemingly shorter time period. These are not intermittent drops. It happens every single time, in exactly the same way. The only variable is how long the connection survives. It doesn't matter what type of traffic I send. I can sit idle, send continuous pings, RDP, transfer files, all of that at once - it makes no difference. The result is always the same. Connected for a few minutes, then silent death. Since I doubt anyone has experienced this exact situation, what steps can I take to troubleshoot my evanescing VPN?

    Read the article

  • how to set up dual wireless routers (G and N) with single broadband connection

    - by user15973
    A local cafe has an 802.11g wireless router attached to either an 8- or 12Mbs broadband connection. Although many customers still have -g devices, an increasing number are showing up with 802.11n devices (e.g. Mac laptops, iPads). The cafe owner is content with his router's area coverage, but he would like for his customers to be able to take advantage of the higher -n download speeds. He could simply replace the -g router with a -n router, but reportedly -n routers slow down considerably when servicing both -g and -n connections. Another option would be to buy the -n router, run an Ethernet cable between the two routers, and (of course) hook up the broadband connection to one of the two routers. Still another option would be to attach an ordinary, wired switch to the broadband connection and then attach both routers to the switch. Aside from the cost issue, what are the tradeoffs of those approaches? Which would you recommend, and why? Is there a better option than the ones I mentioned? Thank you in advance for your advice.

    Read the article

  • Is there any way to prevent a Mac from creating dot underscore files?

    - by SoaperGEM
    At work we're letting one of our very tech savvy clients actually help out a little with a few development projects specific to him. However, he uses his own personal Macbook, and as he edits files on our (Windows) networks, his Macbook always creates a bunch of unnecessary meta files that we end up deleting later. For instance, it creates a file called .DS_Store in any directory he opens, as well as "dot underscore" files for each file he edits. So for instance, if he's editing a file called "Main.php", his Macbook will create another file called "._Main.php". I know there are ways to prevent creation of .DS_Store files, but none about how to prevent creation of these hidden files prefixed with dot underscore. Is there any way to turn that off on Macs? Any way to prevent it from creating those files in the first place?

    Read the article

  • Cannot access shares via \\servername but \\ip works

    - by Jeff
    To set up the scenario: One of our techs set one of the domain controllers to use Microsoft time. The time IS correct (including Time Zone) and DOES match the other domain controller's time; it was previously incorrect, however. Since the change, no users can connect via \\servername\share or \\servername.domainname.com but \\ip\share works fine. I cannot even access it from the other domain controller with which I know both have the same time. The servername DOES resolve to the correct IP address. Also, strangely enough, \\domainname.com works as well which resolves to the same server. Finally Everything that I have tried does resolve to the same, correct IP address. The error is: login failure: The target account name is incorrect. I believe it is time related but since the times are correct and match I'm not sure. Anyone know what might cause this?

    Read the article

  • Can I share my cable internet connection through my ADSL wireless router?

    - by Roaders
    Hi All Over the xmas period I am at my in-laws. They have Virgin Broadband (cable) and have a basic modem / router that is plugged directly into their computer using an ethernet cable. My wife and I arrived with 5 PCs! (ok, one is a gift and won't be used) 4 of which are laptops so I would like to be able to use their internet connection. At the moment I am working so have plugged the ethernet cable into my work laptop. Rebooting the router meant that my work laptop now has internet. I have my ADSL Netgear router which is wireless. I tried plugging it in between the router and the PC but I didn't seem to be able to share the internet connection wirelessly. The original PC still had internet despite ony being connected to my router but my wireless laptop didn't have a connection. My old cable router had an internet ethernet port on the back that the modem plugged into. My ADSL router doesn't, it has a phone connection socket. Is there a way of doing what I want with the equipment I have? Thanks

    Read the article

  • Very Slow DSL (ethernet) speed [New Interesting Update]

    - by Abhijit
    Very IMPORTANT and INTERESTING UPDATE: Due to some reason I just thought to do a complete new setup and this time I decided to again have openSUSE plus ubuntu. So I first reinstall lubuntu and then I installed OpenSUSE 12.2 (64 bit). Now, my DSL speed is working very normal and fine on opensuse. So this is very scary. Is it possible for any operating system to manipulate my NIC so that it will work fine only on that operating system and not on another os? Regarding positive thinking and not being paranoid, what is it that makes ONLY suse to get my NIC to work at normal speed but ubuntu can not do it? Not even fedora? Not even linux mint? What all these OS are lacking that enables suse to work great? == ORIGINAL QUESTION == I 'was' on opensuse 12.2 when my dsl speed was normal. Yesterday I switched from opensuse to ubuntu 12.04 and speed decreased. It came to range of 7-10-13-20-25-kbps. Then I switch to linux mint, and then to fedora. Still slow speed. When I was in ubuntu I disabled ipv6 but still no luck. Now I am in fedora but this time with DIFFERENT ISP. And still I am getting very slow sped. So my guess is this is nothing to do with os. What can be wrong? Is this problem of NIC? Does NIC speed decreases over time? Does NIC life ends over time as with keyboard or mouse? Help please All the os I used are 64 bit and my laptop is Compaq Presario A965Tu Intel Centrino DUal Core. Interesting thing to notice is I get normal speed while downloading torrent inside torrent client softwares. This slow speed issue applied to download from any web browser or installing software using terminal.

    Read the article

  • Clone Microsoft VM > SharePoint issues

    - by Rob
    Hi, We have an existing (production) Hyper-V VM that I want to clone to create a staging server. This server is NOT on a domain/active-directory - uses all local computer accounts. It is Windows 2008 OS, SharePoint 2007, SQL server 2008, Reporting Services, and some custom line-of-business web-applications. We rename the server etc as per the documentation we have, but are having troubles specifically with SharePoint. Some of the sites do not come up, and some issues adding/updating site settings such as site owners. Does anyone know of a definitive resource to this process? thanks Update: We seem to have most working, but the Shared Service Provider, and the SSP's admin site, are not working. In addition, the custom web-parts that reference IIS Session objects are failing (which seem to be related to the Share Service Provider). All the Windows user accounts for various services are renamed during the server cloning, but the windows account names in SQL server are not automatically changed. We've tried to change them in SQL server but still does not seem to work Seems like allot of work - and am thinking that there must be some guidance out there. also getting this: NullReferenceException: Object reference not set to an instance of an object.] Microsoft.Office.Server.Administration.SqlSessionStateResolver.System.Web. IPartitionResolver.ResolvePartition(Object key) +135

    Read the article

< Previous Page | 191 192 193 194 195 196 197 198 199 200 201 202  | Next Page >