Search Results

Search found 30308 results on 1213 pages for 'dont ask'.

Page 196/1213 | < Previous Page | 192 193 194 195 196 197 198 199 200 201 202 203  | Next Page >

  • Video stutter when using external drive

    - by psion
    When using boxee to play video files off of an external western digital 1TB drive formatted NTFS, I notice a slight stutter in the video every 5-10 seconds. When using mplayer, it doesn't stutter as often, but it still stutters occasionally. If I play the video off of the local sata drive, it plays fine even in boxee. I use this computer as my HTPC and I just switched from windows to linux on it. In windows, I never had any sort of stutter playing movies from the drive. I am using the latest intel graphics drivers (for the intel GMA 950) root@eee-htpc:/home/htpc# grep wd /etc/mtab /dev/sdb1 /mnt/wd2 fuseblk rw,nosuid,nodev,allow_other,blksize=512 0 0 I notice that despite trying to use ntfs or ntfs-3g, ubuntu uses ntfs-fuse which I've heard is slower. /dev/sdb1: Timing buffered disk reads: 80 MB in 3.07 seconds = 26.08 MB/sec root@eee-htpc:/mnt/wd2# dd if=/dev/zero of=./120mb bs=1024 count=120000 root@eee-htpc:/mnt/wd2# time mv ./120mb /home/htpc real 0m2.095s user 0m0.016s sys 0m0.736s Even though fuse has a reputation for being slow, it should easily be fast enough for playing standard definition video files. So why the video stutter? edit: The issue seems to be overhead cpu usage from either playing off of a usb device or ntfs/fuse. Watching CPU usage with top, local files use 10-40% CPU. Watching the same video on the external formatted ntfs, it spikes to 170% (over 100% because of hyperthreading). To me it seems like it must be overhead from the fuse driver, though I don't know if it has more or less overhead than ntfs-3g. It's a EEEBox B202 that has an atom 270, so not exactly the most powerful out there. edit2: I believe the solution would be to use non-fuse drivers or different fuse drivers. so far I have not been able to. edit3: I've probably edited this more times than I should, but as an update I have upgraded ntfs drivers to ntfs-3g 2010.8.8 external FUSE 28 - Third Generation NTFS Driver using the following PPA - ppa:x3lectric/team-iquik-releases. When first opening a video file in boxee that's on ntfs there's still the same amount of lag. After a few minutes of video, the lag seems to go away and the cpu usage comes down to 10-40%. Every so often though, it begins to stutter again. Also, if I skip ahead/back in the file, it begins to stutter a lot.

    Read the article

  • How do i disable intel graphics in a hybrid graphics setup?

    - by Eshwar
    Hi, I have a Dell Vostro 3700 version A10. The relevant bits from lspci -v | grep VGA are: 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 18) and 01:00.0 VGA compatible controller: nVidia Corporation GT216 [GeForce GT 330M] (rev a2) so as you can see this is one of those hybrid graphics laptops. Now, I have no interest in any kind of switching. I would like to completely disable the Intel Graphics thats on the processor. I checked in the xorg.log file and it shows that the intel card is in use. from lsmod i see it uses the i915 module. I tried blacklisting that module in /etc/modprobe.d/blacklist.conf but that didn't really work because i still couldn't use the nvidia card for display. I wish there was a BIOS option to disable, but there isn't. Some people have also suggested changing the SATA mode to compatibility, but that does not work either in this case as the intel vga controller still shows up in lspci I tried setting the busid manually in the /etc/X11/xorg.conf file but it still didn't work. It gave me an error that said something along the lines of screen not detected. any bits of xorg.log that you'd like me to attach? So what I am looking for is some solution that allows me to completely disable the use of the intel vga controller. if it was blocked somehow it'd be nice. as if it were not present. Any suggestions? I am desperate here actually. Because I cannot use the HDMI port right now on my laptop for that reason. My guess is this applies to desktops that also have Core i5 processors with onchip graphics as well as dedicated graphics cards. How would they go about solving the problem?

    Read the article

  • power management of USB-enclosed hard drives

    - by intuited
    With a typical USB hard drive enclosure, is the full range of drive power management functionality available? In what may be an unrelated matter: is it possible to suspend a PC without unmounting an attached USB-powered drive, and then remounting it on resume? This is the behaviour I'm currently seeing (running Ubuntu linux 10.10). Are there certain models or brands that provide more complete control over this aspect of drive operation? My Friendly Neighbourhood Computer Store carries (part of) the Vantec Nexstar product line.

    Read the article

  • Getting a TV Capture Card working

    - by Benny Hallett
    I'm new to Linux, and am trying to get my Capture Card working on 11.04. The only command that I know to run to find out any information is lspci, which tells me that I have 02:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885 PCI Video and Audio Decoder (rev 04) I've looked at using Me TV, but haven't worked out how to configure it for my card, or what I need to do to get it running. I'm not fussed on what software I use to run the Capture Card, but I've currently got only Me TV installed. Edit: When I run tvtime, I get the following errors: videoinput: Cannot open capture device /dev/video0: No such file or directory mixer: find error: Success mixer: Can't open mixer default, mixer volume and mute unavailable. mixer: Can't open device default/Line, mixer volume and mute unavailable. Segmentation fault

    Read the article

  • SysRq+REISUB hangs at "resetting" (without actually resetting/restarting) in Maverick

    - by Andrei
    I'm trying SysRq+REISUB to see how it would be used to restart my system safely in case of emergency. However, I find that SysRq+REISUB hangs at "resetting" (without actually resetting/restarting) in Maverick. All other SysRq combinations appear to work correctly (i.e. SysRq+REISU). cat /proc/sys/kernel/sysrq returns 0. But I'm not sure it's relevant because SysRq certainly works. What can I do to have "B" actually restart the system? Thanks!

    Read the article

  • Menubar hidden in all KDE apps

    - by Francesco Feltrinelli
    I am using Kubuntu 10.10 with Plasma-Netbook on my netbook. Somehow I messed up with window's settings and now the menubar (the one on top of the window, just below the titlebar, which has the File button, Edit, Settings, Help, ...) is hidden from all my KDE applications. Here you can see how the menubar should be correctly displayed: Here you can see how it is actually displayed on my netbook: I don't remember what I did to hide the menubar, I clicked somewhere in the context menu which shows right-clicking on window title, but I cannot find that setting anymore. Can you please help me? Thank you very much.

    Read the article

  • Unable to sync time using `ntpdate`, error: "no server suitable for synchronization found"

    - by William Ting
    My ntp.conf file: user@pc[0][07:37:40]:/etc$ cat /etc/ntp.conf idriftfile /var/lib/ntp/ntp.drift server 0.pool.ntp.org server 1.pool.ntp.org server 2.pool.ntp.org server pool.ntp.org Command output: user@pc[0][07:37:24]:/etc$ sudo ntpdate -dv pool.ntp.org 18 Jun 07:37:35 ntpdate[10737]: ntpdate [email protected] Tue Apr 19 07:15:05 UTC 2011 (1) Looking for host pool.ntp.org and service ntp host found : conquest.kjsl.com transmit(198.137.202.16) transmit(216.45.57.38) transmit(64.6.144.6) transmit(198.137.202.16) transmit(216.45.57.38) transmit(64.6.144.6) transmit(198.137.202.16) transmit(216.45.57.38) transmit(64.6.144.6) transmit(198.137.202.16) transmit(216.45.57.38) transmit(64.6.144.6) transmit(198.137.202.16) transmit(216.45.57.38) transmit(64.6.144.6) 198.137.202.16: Server dropped: no data 216.45.57.38: Server dropped: no data 64.6.144.6: Server dropped: no data server 198.137.202.16, port 123 stratum 0, precision 0, leap 00, trust 000 refid [198.137.202.16], delay 0.00000, dispersion 64.00000 transmitted 4, in filter 4 reference time: 00000000.00000000 Thu, Feb 7 2036 0:28:16.000 originate timestamp: 00000000.00000000 Thu, Feb 7 2036 0:28:16.000 transmit timestamp: d1a71a93.1f16c1e3 Sat, Jun 18 2011 7:37:39.121 filter delay: 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 filter offset: 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 delay 0.00000, dispersion 64.00000 offset 0.000000 server 216.45.57.38, port 123 stratum 0, precision 0, leap 00, trust 000 refid [216.45.57.38], delay 0.00000, dispersion 64.00000 transmitted 4, in filter 4 reference time: 00000000.00000000 Thu, Feb 7 2036 0:28:16.000 originate timestamp: 00000000.00000000 Thu, Feb 7 2036 0:28:16.000 transmit timestamp: d1a71a93.524a05dd Sat, Jun 18 2011 7:37:39.321 filter delay: 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 filter offset: 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 delay 0.00000, dispersion 64.00000 offset 0.000000 server 64.6.144.6, port 123 stratum 0, precision 0, leap 00, trust 000 refid [64.6.144.6], delay 0.00000, dispersion 64.00000 transmitted 4, in filter 4 reference time: 00000000.00000000 Thu, Feb 7 2036 0:28:16.000 transmitted 4, in filter 4 reference time: 00000000.00000000 Thu, Feb 7 2036 0:28:16.000 originate timestamp: 00000000.00000000 Thu, Feb 7 2036 0:28:16.000 transmit timestamp: d1a71a93.524a05dd Sat, Jun 18 2011 7:37:39.321 filter delay: 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 filter offset: 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 delay 0.00000, dispersion 64.00000 offset 0.000000 server 64.6.144.6, port 123 stratum 0, precision 0, leap 00, trust 000 refid [64.6.144.6], delay 0.00000, dispersion 64.00000 transmitted 4, in filter 4 reference time: 00000000.00000000 Thu, Feb 7 2036 0:28:16.000 originate timestamp: 00000000.00000000 Thu, Feb 7 2036 0:28:16.000 transmit timestamp: d1a71a93.857c6fbd Sat, Jun 18 2011 7:37:39.521 filter delay: 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 0.00000 filter offset: 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 0.000000 delay 0.00000, dispersion 64.00000 offset 0.000000 18 Jun 07:37:40 ntpdate[10737]: no server suitable for synchronization found

    Read the article

  • problem in eclipse installation in Ubuntu 12.04

    - by Srijan
    Have tried more than dozen times to install Eclipse version available in the Ubuntu Software Center still to no avail. Every time I try to install it shows error i.e. unable to install. Have tried to install it using terminal as well with still the same results. After installation it refuses to run. What to do or any other packages I can use instead of Eclipse. Mainly trying to run java programs through eclipse. Thanks for the time. Am using Ubuntu 12.04 on x86-64 bit architecture.

    Read the article

  • unity, seeing all instances of same open application windows on all virtual desktop

    - by Nasser M. Abbasi
    I noticed this strange issue with unity. I am using 12.04. The desktop has 4 virtual desktops, which I can switch between using the 'workspace switcher' which is very nice. But I noticed the following: When I have 2 instances of the same app (say 2 different firefox windows, or 2 different terminal windows), in 2 different virtual desktops, then I click on the icon for that application located on the launcher panel (the left long strip with icons on it), then I see the application comes into focus. Then when I click again right away (on the same icon on the launcher), then now all instances of this application that are open come into ONE view (may be on was on desktop 1, and the other was on desktop 3 for example) and then I can now click on the one instance window that I want to select to use. This is all very nice actually. But this does NOT work for all applications! I just tried it, and it worked for firefox, and for gedit and for the gnome terminal. I have one firefox window open in virtual desktop 1, and another window open in virtual desktop 2. I clicked once on the firefox icon, then again, and both windows came into the main desktop and I was able to select which one to use. When I tried the same thing on dolphin file manager, which I also had 2 windows (instances) of it open in 2 different virtual desktops, this behavior did not happen. I clicked again, and nothing happened. Only one remained in focus. So I had to fo look for the second dolphin window the hard way. It looks like some apps are supported by this feature and some are not. How does one make it so that all applications are supported like this? This is a very handy feature. Is it a configuration item somewhere? thanks

    Read the article

  • Error installing MySQL Ubuntu 12.04, dependency?

    - by user86736
    I'm trying to install MySQL 5.5 on Ubuntu 12.04, but I'm stuck with this error: Setting up mysql-server-5.5 (5.5.24-0ubuntu0.12.04.1) ... start: Job failed to start invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.5 (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of mysql-server: mysql-server depends on mysql-server-5.5; however: Package mysql-server-5.5 is not configured yet. dpkg: error processing mysql-server (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: mysql-server-5.5 mysql-server E: Sub-process /usr/bin/dpkg returned an error code (1) Thanks for help!

    Read the article

  • Cannot connect to secure wireless with Netgear wna3100 USB

    - by Vince Radice
    I have installed Ubuntu 11.10. I used a wired connection to download and install all of the updates. When I tried to use a Netgear WNA3100 wireless USB network adapter, it failed. Much searching and trying things I was finally able to get it working by disabling security on my router. I have verified this by disabling security and I was able to connect. When I enabled security (WPA2 PSK), the connection failed. What is necessary to enable security (WPA2 PSK) and still use the Netgear USB interface? Here is the output from the commands most requested lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] lshw -C network *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:40:ca:44:e6:3e size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=32 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:c800(size=256) memory:ee011000-ee0110ff memory:40000000-4000ffff *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: e0:91:f5:56:e1:0d capabilities: ethernet physical wireless configuration: broadcast=yes driver=ndiswrapper+bcmn43xx32 driverversion=1.56+,08/26/2009, 5.10.79.30 ip=192.168.1.104 link=yes multicast=yes wireless=IEEE 802.11g iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11g ESSID:"vincecarolradice" Mode:Managed Frequency:2.422 GHz Access Point: A0:21:B7:9F:E5:EE Bit Rate=121.5 Mb/s Tx-Power:32 dBm RTS thr:2347 B Fragment thr:2346 B Encryption key:off Power Management:off Link Quality:76/100 Signal level:-47 dBm Noise level:-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ndiswrapper -l bcmn43xx32 : driver installed device (0846:9020) present lsmod | grep ndis ndiswrapper 193669 0 dmesg | grep -e ndis -e wlan [ 907.466392] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 907.838507] ndiswrapper (import:233): unknown symbol: ntoskrnl.exe:'IoUnregisterPlugPlayNotification' [ 907.838955] ndiswrapper: driver bcmwlhigh5 (Netgear,11/05/2009, 5.60.180.11) loaded [ 908.137940] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmwlhigh5, version: 0x53cb40b, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 908.141879] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 908.143048] usbcore: registered new interface driver ndiswrapper [ 908.178826] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 994.015088] usbcore: deregistering interface driver ndiswrapper [ 994.028892] ndiswrapper: device wlan0 removed [ 994.080558] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 994.374929] ndiswrapper: driver bcmn43xx32 (,08/26/2009, 5.10.79.30) loaded [ 994.404366] ndiswrapper (mp_init:219): couldn't initialize device: C0000001 [ 994.404384] ndiswrapper (pnp_start_device:435): Windows driver couldn't initialize the device (C0000001) [ 994.404666] ndiswrapper (mp_halt:262): device e05b6480 is not initialized - not halting [ 994.404671] ndiswrapper: device eth%d removed [ 994.404709] ndiswrapper: probe of 1-5:1.0 failed with error -22 [ 994.406318] usbcore: registered new interface driver ndiswrapper [ 2302.058692] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmn43xx32, version: 0x50a4f1e, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 2302.060882] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 2302.113838] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2354.611318] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2355.268902] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2365.400023] wlan0: no IPv6 routers present [ 2779.226096] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2779.422343] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2797.574474] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2802.607937] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2803.261315] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2813.952028] wlan0: no IPv6 routers present [ 3135.738431] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3139.180963] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3139.816561] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.229872] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.444542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.758297] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.860684] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.118732] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.139553] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.300542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3353.341402] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3363.266399] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.505475] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.506619] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3363.717203] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.779206] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.206152] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.248624] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.577664] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3438.852457] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3438.908573] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.282995] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.325237] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.460716] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.461763] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.809776] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.880641] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.122848] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.148328] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.324502] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3636.088798] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3636.712186] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 3647.600040] wlan0: no IPv6 routers present I am using the system now with the router security turned off. When I submit this, I will turn security back on.

    Read the article

  • Bash does not remember programs with non 0 exit status in history

    - by Amigable Clark Kant
    I enter a command. It fails. I press arrow up, modify something and enter it again ... hold it right there. It used to work like that. Now it's more like: I enter a command. It fails. I press arrow up, get the last command which didn't fail, likely "ls" or something useless and I type the whole thing again back by hand. What happened? It wasn't always like this. But it's quite some time since this behavior changed, I'll give you that. Some years ago, at least. How do I put some sanity back into my bash prompt?

    Read the article

  • How to manually set color of Unity Panel?

    - by JamesTheAwesomeDude
    I was just wondering if there's a way to set the color of the Unity panel manually, as opposed to having it derived from smooshing all the colors of the wallpaper together. (the launcher on the left side of the screen that comes default in Ubuntu is the Unity Panel, right? If not, please correct me on my terminology.) The reason I want this is because I have this cool wallpaper I found on DeviantArt, and I used GIMP to make Dawn, Dusk, and Midnight versions of it. Then, I set them with a transition effect, so that the lighting changes over the course of the day. Unfortunately, the Unity Panel turns a sickly sewer green at night (it could also be said to look like radioactive barf.) Either way, I don't like my launcher thingy looking like that. I'd prefer to stay away from programs that let you customise the Unity Panel (I'm fine with using sudo nano to edit system config files,) but I would if it were the only option. Here are some screenshots, one with a grey-themed wallpaper, one with lots of red, and the hill at night, (the one that makes the unity panel look like radioactive barf.): http://imgur.com/a/0Gqcd

    Read the article

  • How to remove individual Unity Webapps' items from message indicator?

    - by Danial Behzadi
    In first days of trying Ubuntu 12.10 I installed a bunch of unity webapps like Launchpad, Twitter, Facebook, LinkdIn, etc. Recently I found some of them useless and removed the related "unity-webapps-*" packages. They no longer appear in the Launcher and Every time I visit the main website in firefox, they offer to install the unity webapp for that specific website as well. But the problem is the items for them (LinkedIn, Twitter and Facebook) are placed in the message indicator yet after Thunderbird and Of course they don't indicate anything. How can I completely remove the webapps items from unity?

    Read the article

  • After installing cinnamon 1.6 the unity desktop environment has some cinnamon settings

    - by deepak365
    Issue: After installing cinnamon 1.6 the unity desktop environment having some cinnamon settings. Yesterday I installed cinnamon 1.6. It causes some changes in my unity desktop environment. After login in Unity: I am getting a "Open in a terminal" option while right-clicking on a desktop. While I am trying to open "Change Background Option " after right-clicking on desktop, cinnamon setting is opened instead of Ubuntu default setting. Please help me to getting back default options in unity desktop. (I don't want to remove cinnamon). I am using Ubuntu 12.10

    Read the article

  • Accidentally deleted /etc/X11/xorg.conf.original, and now log in no longer works

    - by Cester Nilap
    I accidentally deleted xorg.conf.original-0; xorg.conf.fglrx xorg.conf.fglrx-0-1, after I tried to install fglrx drivers on the graphics card, which in fact worked on 13.04 and now as I went to 13.10 has not worked. Now I can just switch to a new TTY with: Ctrl + Alt + F2 I found this which is for nVidia cards TO install the fglrx drivers for graphic card I used this tutorial Is there any possibility that I can recover, replace, rebuilb that xorg.conf.original-0, and if exists any possibility where I could start from.

    Read the article

  • youtube-dl not performing as expected on 12.10

    - by J2big
    When I type the video url, it bring out this message instead of download. Please what do I do because I really need to start downloading videos. joshua@joshua-HP-625:~$ youtube-dl http://www.youtube.com/watch?v=h3gPo7qFOFw& feature=player_detailpage [1] 6720 joshua@joshua-HP-625:~$ Hi! We changed distribution method and now youtube-dl needs to update itself one more time. This will only happen once. Simply press enter to go on. Sorry for the trouble! The new location of the binaries is https://github.com/rg3/youtube-dl/downloads, not the git repository.

    Read the article

  • Ubuntu and VirtualBox

    - by Sinan
    I have the following configuration, A host running Windows 7; A guest running Ubuntu 14.04 LTS (VirtualBox); I am connecting a Cisco router directly to my PC running Windows 7 and testing the router for netflow packets in the virtualBox I am having a difficulty capturing the traffic of the netflow from the Cisco device in my virtualBox using port 2222. I tried to use the many different networking modes provided by virutalBox (i.e. NAT, Bridged Adapter, Host only adapter) but I am not successful in capturing the netflow traffic. Could you please advise me on the configuration setup that need to be done on the virtual box to allow capturing the traffic coming from the router. I successfully capture the netflow traffic on my PC (windows 7). Thank you

    Read the article

  • How to find the list of all available packages along with the lastest version number available in the repositories?

    - by Avinash Raj
    I want to list all the packages(installed or not installed) along with the latest version number available in the repositories. For example: The output of apt-cache policy chromium-browser shows like below $ apt-cache policy chromium-browser chromium-browser: Installed: (none) Candidate: 34.0.1847.116-0ubuntu2 Version table: 34.0.1847.116-0ubuntu2 0 500 http://ftp.cuhk.edu.hk/pub/Linux/ubuntu/ trusty/universe amd64 Packages So the latest version of chromium-browser package available in the repository is 34.0.1847.116-0ubuntu2. Like that, i want to list the version number along with the package names that are available in repositories. And all i want to do this through command-line. I want the output to be like this, chromium-browser 34.0.1847.116-0ubuntu2 xxxxxxxxxxxxxx yyyyyyyyyyy ............ ............

    Read the article

  • PXE booting on old computer

    - by kosciak
    So my computer is not working - the disk is totally cleared, I've deleted GRUB and PLOP which I used to install new system, because CD-Rom is broken and BIOS is old (whole computer is old, it's Sony Vaio PCG-GR250) so it won't allow me to do it via USB and I got no floppy drive :) the only way is to PXE boot PLOP and install Linux from USB after PLOP has been opened. (I'm not a specialist but that's how I see it) I'm using Mac OS X 10.9 and I followed number of tutorials how to set up TFTP and DHCP server and I got PLOP here, but when I boot up with PXE it says that it found DHCP but TFTP timed out. Any help or alternative way of rescuing old laptop? Thanks in advance!

    Read the article

  • Ubuntu Touch Official Hardware? [duplicate]

    - by user1628
    This question already has an answer here: Where can I get a device with 'Ubuntu for phones' pre-installed? 1 answer I really like the look of Ubuntu touch and I want it ASAP, however, I am NOT willing to buy a device simply to port ubuntu touch on it. I don't want to void all warranties and take any risks. Therefore, I am really just waiting for official ubuntu touch hardware (devices made for ubuntu touch). I can't find any rumours or estimated release dates online, in fact, I can't find out anything at all. Can anyone? If so, what and where? When do you think they'll be official hardware? What price do you think it'll be? Do you think canonical/ubuntu will manufacture it themselves? Thanks, Zach

    Read the article

  • sed problem with scripting

    - by Pablo Ramos
    I am trying to run a script using sed i runing like this for et in 1 # 2 3 do if [ -d ET$et ]; then rm -rf ET$et; fi mkdir ET$et cd ET$et cp $home/step_$i/FDE/diabatA/run.adf . cp $home/step_$i/FDE/diabatA/mas$i.xyz . awk1=`awk '/type=fde/{print NR }' run.adf | head -1` awk2=`$(echo "$a+379" | bc -l )` sed -n "$awk1,"$awk2"p" run.adf > first awk3=`awk '/ATOMS/{print NR +1}' first` awk4=`cat mas$i.xyz | wc -l` awk4=$( echo "$awk4-1" | bc -l ) awk5=`awk "/ATOMS/{print NR +"${awk4}" }" run.adf` sed -n "$awk3,"$awk4"p" first > atoms par=$( echo "$awk4-99" | bc -l ) rho1=$(cat atoms | head -34 ) rho2=$(cat atoms | head -64 | tail -31) rho3=$(cat atoms | head -97 | tail -33) rhoall=$(cat atoms | tail -${par} ) echo -e "$rho1\n$rho2\n$rhoall" > eje done but is telling me this: (standard_in) 1: syntax error sed: -e expression #1, char 6: unexpected `,' sed: -e expression #1, char 1: unknown command: `,' Please, I appreciate any help with this issue... Thanks Pablo

    Read the article

  • How to show context menu when right-click released?

    - by Kev
    I'm using Ubuntu 10.04. When I right-click, menu popup too quickly, and the first menu item is clicked. If I right-click in desktop, it create a new folder sometime. If I right-click in terminal, it open a new terminal sometime. ... Is there some way to delay context menu? Or how can I offset context menu a little bit pixels to the right-bottom direction? (like firefox) Or how can I config Gnome to popup menu when right-mouse released? (like windows xp)

    Read the article

  • Problems with subversion (in gnome keyring, maybe), user=null

    - by Tom Brito
    I'm having a problem with my subversion in Ubuntu, and it's happening only on my computer, my colleagues are working fine. It asks for password for user "(null)": Password for '(null)' GNOME keyring: entering the password it shows: svn: OPTIONS of 'http://10.0.203.3/greenfox': authorization failed: Could not authenticate to server: rejected Basic challenge (http://10.0.203.3) What can be causing that (again: it's just on my computer, the svn server is ok).

    Read the article

  • How to manage two video cards on a laptop that runs Ubuntu 10.10?

    - by Marc-François Cochaux-Laberge
    I have a laptop with two video cards. One ATI and on integrated Intel. On Windows, I can choose which video card I want to use. For example, I use the Intel card for normal use and for gaming, I switch to my ATI card for better performance, but a shorter battery life. In Ubuntu 10.10, only the Intel driver is installed, the ATI driver for my card doesn't work at all and there's heat coming out of my computer all the time, like when I'm playing video games on Windows. I think both cards are active, but only the Intel one is usefull. How can I solve this by making sure Ubuntu is aware of the two video cards and by disabling my ATI. Or may be I am all wrong about this?

    Read the article

< Previous Page | 192 193 194 195 196 197 198 199 200 201 202 203  | Next Page >