Search Results

Search found 7555 results on 303 pages for 'installing'.

Page 196/303 | < Previous Page | 192 193 194 195 196 197 198 199 200 201 202 203  | Next Page >

• How would you diagnose an integrated network card that doesn't show up on the device list?

  - by Tomer Gabel

  I've been setting up a server based around a Gigabyte GA-G33M-DS2R motherboard (G33, PCH9R with integrated Realtek 811B network device. I've enabled it in the BIOS, but it doesn't show up in the pre-boot PCI device list, isn't recognized by Windows (even after installing the chipset and networking drivers) and doesn't even show up via lspci. I've tried cycling power, disabling, cycling again, enabling, cycling again etc. to no avail. I'm sort of at a loss at this point; the board isn't under warranty anymore, but I'd rather not have to replace it. Any advice would be greatly appreciated...

  Read the article

• RAID1: Migrate HHD to SSD?

  - by OMG Ponies

  My current workstation uses an Adaptec 5805, with Win2008 mirrored between two 72 GB (10K?) savvio drives. My question is if there's a way to migrate the mirror to use SSDs - I've been looking at 90GB Corsair Force (Sandy Bridge) to replace the existing setup. If it's possible, without installing the OS fresh. If I replaced the mirrored drive with an SSD, would the array sync the drives? Then I could promote the SSD mirror to be the primary, and use the second SSD as the mirror. That'd be too easy... Or should use Ghost to get an image of the existing setup, apply it to the SSD for a new mirror to be setup on?

  Read the article

• Problem reinstalling GRUB

  - by DisgruntledGoat

  I have a PC that dual-boots Ubuntu and Windows Vista. I recently reinstalled Windows Vista after some problems and now the bootloader's gone. I've been trying to follow this Ubuntu community guide but it's not working. I have Grub Legacy according to the first part (I installed Ubuntu 9.04 originally then upgraded). From the 9.04 LiveCD, I ran this: sudo grub-install --root-directory=/media/disk /dev/sda5 sda5 is the Ubuntu partition. I get this output: grub-probe: error: Cannot open `/boot/grub/device.map` [: 494: =: unexpected operator Installing GRUB to /dev/sda5 as (hd0,4)... Installation finished.No errors reported. This is the contents...(etc) (hd0) /dev/sda In the bit below, when I run setup (hd0) I get an error, "Error 17: Cannot mount selected partition" Little help?

  Read the article

• how to start with unmanaged vps?

  - by GaVrA

  Hello! I have a managed VPS, so whatever i need i can just ask my support, and they will do it for me. Now i plan to migrate to unmanaged VPS, so i need some guides, tips on how and where to start learning. I will have more specific questions once i start using it, but now i just need some general answers about this topic. Thanks. Update: Ok, i have decided to go for unmanaged VPS with cPanel. OS is CentOS-5. I contacted support only for some small(i think) things like creating new account in whm, some database importing, installing new software(rare)... What i will be using is apache, php, mysql. I think i will be able to cope with upgrading to new versions, so the thing that interests me the most is security i guess.

  Read the article

• Ubuntu 14.04 says insufficient memory in my /boot memory alocation while updating

  - by Aravind Dollar

  I am new to Linux platform. I just tried installing Ubuntu alongside windows but allocated only 200 mb to the /boot partition which is not recommended. Now Ubuntu software update keep on insists me no enough space. What should I do? Is there any way to increase my /boot partition without removing the total OS? Or should I completely uninstall Ubuntu and put it back? Please anyone suggest me over this issue. I have no idea what to do. And please be elaborate, as I am new to Linux environment.

  Read the article

• MSSQL: Choice of service accounts

  - by Troels Arvin

  When installing MS SQL Server 2008, one needs to associate a service account with the installation (possibly even several accounts, one for the SQL Server Agent, one for Analysis Services, ..., but let's leave that for the case of simplicity). The service account may be local account, or a Windows domain account. If a domain account is used: Can MSSQL start, if connectivity to the domain controllers is temporarily down? If the answer is yes: Should each DBMS instance on each server have a separate account, or does it make sense to use a particular "MSSQL" domain account on all MSSQL-installations in the organization? If separate accounts are used for each instance on each server: Does it make sense to create a special MSSQL security group in the domain and place all the MSSQL service accounts in that group, perhaps to ease replication, etc? Is there a common, generally accepted naming convention for MSSQL service account(s)?

  Read the article

• OSX - Update "Java for OS X 2012-002" is not mentioned on support.apple.com, is this ok?

  - by snies

  Straight after installing "Java for OS X 2012-001" Software Update asks me to install "Java for OS X 2012-002", which has the exact same size (66.6 MB) and description (including the same two links: HT5055 and HT1222) as the former, which strikes me as odd. The "Java for OS X 2012-001" is described on the apple support pages, but the "Java for OS X 2012-002" is not mentioned anywhere. Also searching on google does not yield any usable results. What is your opinon? Am i paranoid? Did you also see this update?

  Read the article

• Font display issue (Mac OS X)?

  - by avenas8808

  I used a font manager on Mac OS X, for additional fonts in my graphic design projects without installing them to the fonts folder (I think that's how it works) - using Font Book and Font Explorer X Version 1.2.3 on OS X 10.6. Most fonts work fine, but Interstate has a problem: Interstate Regular is installed, but for some reason it's probably not seeing it; it's seeing all the Bold and Condensed versions fine. In the above image, it displays the second font as Interstate Regular, but it isn't that font... why? Also, how do I reset the system fonts folder back to the default-installed fonts (I think it's in the library folder) if worst comes to worst, and is using a font manager on Mac or Windows a good idea? I don't want to wreck my system, fairly new to using Mac, especially OS X, so any help would be gratefully accepted.

  Read the article

• How to fix error "To run this application, you first must install one of the following version of the .Net Framework: v2.0.50727"?

  - by Gravitas

  How do I fix the error that started popping up in a lot of applications: To run this application, you first must install one of the following version of the .Net Framework: v2.0.50727. Would you like to download an install version v2.0.50727 of the .NET framework now? Unfortunately, this is not as simple as just installing the .NET 2.0 runtime, because its already installed. If I run the recommended installers for .NET 2.0 or .NET 3.5 SP1, it exits silently. Events leading to problem: Installed SQL Server 2008 R2, which installs a toy version of Visual Studio 2008 that only deals with SQL specific projects. Uninstalled Visual Studio 2008.

  Read the article

• git: command not found

  - by B6431

  Using github for the first time. In terminal I receive this error git: command not found If I type in terminal which git it returns nothing. If I type which github it returns /usr/local/bin/github Github's command line utility seems to be installing a github but not a git. echo $PATH returns /usr/bin:/bin:/usr/sbin:/sbin:/usr/local/bin:/usr/X11/bin. Currently do not have a .bash_profile or .profile. Not sure if that is significant. Am a command line and $PATH rookie but am determined to learn. Mac OS version 10.6.8 and Github version 1.2.8. All advice is appreciated.

  Read the article

• Extract Certs from Apache

  - by user271619

  Recently I've had to uninstall a single Self-Signed SSL Certificate from one of my Apache boxes, specifically for an outside party. That's not really a problem for me, since it was easy. What confuses me is how they knew I had a self-signed certificate. The domain I provided them was not related to the domain with the self-signed certificate. Does this mean Apache publicizes the Virtual hosts in the httpd.conf file? I asked the outside party what software they used to extract information from my server, and they provided this GitHub link: https://gist.github.com/4ndrej/4547029 I figured I'd ask the community first, before I attempt installing the Java program.

  Read the article

• Running System Center Configuration Manager on a Domain Controller

  - by Brent D

  We are a smallish educational network (about 70 clients) with a single server running Windows Server 2008 Enterprise, functioning as both domain controller and file server. The educational pricing for Microsoft Forefront Endpoint Protection 2010 is irresistible as a managed anti-malware solution, but it requires System Center Configuration Manager 2007. I know best practice is not to run System Center Configuration Manager on a domain controller, but it's the only server I have to work with. Will installing SCCM on a domain controller cause problems? What conflicts might I need to take into account when planning deployment?

  Read the article

• MediaPortal crash when scanning my TV Channels

  - by Martin Ongtangco

  I tried installing MediaPortal on my old system. I installed & tried both beta & stable releases: Here's the old system specs: Windows XP SP3 512MB DDR 80GB IDE K-World PVR-TV7131 Analog TV-Tuner Inno3d FX5500 128MB 64bit When scanning through the TV-Server, it crashes. I don't know if the incompatibility comes from the hardware or the OS, but my TV Tuner's own Media center app works well. For now, that's what im using. Anyone here familiar with MediaPortal? Thanks!

  Read the article

• Making an SSD drive the primary boot/system drive

  - by David Ebbo

  [Not much of a hardware guy, so please excuse my ignorance :)] I just ordered an HP Pavilion Elite HPE-450t (desktop), which came with Win7 installed on the hard drive, using two partitions (C: and D:). Separately, I bought a 128GB SSD that I intend to use as my system drive. I got it in there and connected it, and right now, it's the J: drive (which was the first letter available in disk manager). My goal is for the SSD to get a clean OS install be the C: drive, and to clean out the other hard drive and make it D: (for misc data storage) Question #1: the motherboard has two SATA plugs. Does it matter which one I use for which drive? Question #2: what's the right way to install Win7 on the SSD in a way that it ends up being the C: drive? Do I need to switch some things around in the current Win7 that came with it, are can I do all that while installing Win7 on the SSD?

  Read the article

• Clearos open vpn vs windows open vpn client where client connects with no default gateway

  - by Paul

  Am using clearos as open vpn server and configured my users on windows machine with open vpn client. My problem is that users connect to the server without a default gateway and also with ip conflicts, i can ping the server but i can not ping any user behind the server. please any one can help to find out what causes the clients to connect without a default gateway and also not to be able to ping any user behind the clearos open vpn server. Help with a step by step guide of installing open vpn on clearos and open vpn clients on windows. Thanks

  Read the article

• How do I turn off the click sound when closing a tab in chrome?

  - by nos

  Every time I close a tab in Chrome, it makes a click sound. How do I turn off that sound? I reported that issue back in Oct 2010. The problem doesn't appear on all clients and the reason is still unclear. Common attempts at solving the issue include simply turning off the sound in Windows. But I would prefer to solve the problem at the source. Why is Chrome even triggering that sound to be played? And why is it delayed? The problem would be far less annoying if the sound could easily be related to the action taken. Installing the Chrome Toolbox and muting all tabs has no effect on this issue. When switching to a different Chrome user profile, the new user profile does exhibit the same issue.

  Read the article

• WSS "Cannot connect to the configuration database"

  - by Tim

  I have 64-bit WSS 3.0 installed on a 64-bit Windows 2003 Server. After installing WSS 3.0 I switched IIS to run in 32-bit emulation mode as we have some applications that require this. I'm getting a "Cannot connect to the configuration database" trying to get to the Central Admin page and wondered if: a. The setup I have won't work and I'm wasting my time trying to figure this out. or b. If anyone has any suggestions for resolving the database connection issue? The identity of the app pool that WSS runs under has all the required permissions in SQL so far as I can tell. Any help would be appreciated!

  Read the article

• DRAC for remote OS install w/o Virtual Media

  - by The Diamond Z

  I have a few DELL servers in a remote DC and our ISP has been very kind about doing OS installs for us. However, as we move to Production and multiple DC's I'd like to be able to do the installs/re-installs internally and DRAC Enterprise w/SDRAM seems ideal. My question is, how do you get your install ISO's on to the SDRAM? Can I just copy it from a local DVD (temp USB hookup) or FTP? What's the advantage to the SDRAM over just buying a USB dongle (to leave plugged into the server) and installing a bootable install ISO? We're a virtual org generally using DSL (2mb) connections to the DC over the Internet and using 'Virtual Media' isn't viable for us.

  Read the article

• Windows 7 Pro - "domain" like login screen appeared

  - by Adrian

  I'm setting up a new PC with the Windows 7 Pro. After some actions (software installing, config changes, applying updates ), my login screen looks like the PC is connected to the domain: I have checked the settings and everywhere the "workgroup" is checked. I have been googling for three hours trying some solutions (Control UserPasswords2, regedit and the ".DEFAULT" key) but nothing works. I cannot see the user icons - only the login screen as above. I cannot also change the account icon. Has anybody seen such an issue?

  Read the article

• Sound card issues (High Definition Audio Controller)

  - by Prakash R

  I have a 5-year-old Acer Aspire 4520. Until a month back it was working beautifully on Windows 7 32bit. But then out of the blue, the sound stopped working. I've tried reinstalling the OS 3-4 times. The sound came back a couple of times, but it stopped working after a reboot. Even after installing the sound drivers, I don't see any entry in the Playback tab of the Sound applet in Control Panel. I see a High Definition Audio Controller entry in Device Manager. I disabled and uninstalled it, but Windows reinstalls it automatically. I'll share specific hardware details if anybody here needs to know. The processor is "AMD Athlon(tm) 64 X2 Dual-Core Processor TK-55". Any help would be appreciated.

  Read the article

• WAMPServer updates from WAMPServer Alive project... are they safe?

  - by Narcissus

  Hi all... I've been using WAMPServer for a fair while and been really happy with it. Unfortunately I've been itching for an Apache 2.2.15 addon for it (currently there's only a 2.2.14 one). I know that I can 'manually' install an updated version, but I really did appreciate the ease of just installing the addon and having the paths etc. set correctly. Anyway, in my search, I came across the WAMPServer Alive project at http://sourceforge.net/projects/wampserveralive/ . My question is pretty basic: does anyone have any experience with addons from this project? Are they safe to use? Is there any reason in particular that I should not trust it? Thanks!

  Read the article

• PHP 5 will not work in Centos 6 for me

  - by LaserBeak

  Just created a new install of Centos 6.0 64-bit on a virtual machine and running on Vmware workstation 8, windows host. yum install php service httpd restart And when trying to run a html file from the var\www\html dir which just has <?php phpinfo(); ?> in it or pointing browser to localhost. Nothing comes up. Also opened up httpd.conf and added: AddType application/x-httpd-php .php AddType application/x-httpd-php-source .phps Tried reinstalling, installing php-common, then php etc. to no avail. Otherwise going for the typical LAMP. installed: php.x86_64 5.3.2-6.el6_0.1 @updates php-cli.x86_64 5.3.2-6.el6_0.1 @updates php-common.x86_64 5.3.2-6.el6_0.1 @updates Yet to update to Centos 6.1 PHP5 is probably comes installed by default with Centos and I maybe stuffed it up by running yum install php?

  Read the article

• Install multiple Linux OS using WUBI

  - by soul

  I want to install Linux Mint, and Ubuntu on my laptop using Wubi installation. I already installed Ubuntu, but when I launch the Wubi installer for Mint. I got this guy: Does it mean to say that I can only install one os using the wubi? Do you know of any solution to this problem, except by installing mint using the usual way. I have XP and Windows 7 installed on the machine. That's why I'm using Wubi so that I won't get into troubles.

  Read the article

• HP laptop won't recognize wireless adapter

  - by Dennis Williamson

  I have an HP Pavilion dv6400 series laptop with an NVidea chipset which is the subject of a class action lawsuit. The symptom (PDF) that I'm experiencing is that the system fails to recognize that there is a wireless adapter installed. It doesn't appear in Device Manager. Is there some way, short of installing a new adapter, that I can work around this problem? The system is running Windows Vista Home and has the latest BIOS (F42) and Windows updates and drivers. See this related question where I ask how to use an old Windows Mobile phone as a Wi-Fi (not cellular data) tether.

  Read the article

• Why are my hardware tabs disabled for my VMWare player image?

  - by djangofan

  I just installed a Ubuntu 10.10 image on VMWare player and after I finished installing I was messing with the hardware settings and I did the following: 1. disabled the floppy device 2. changed the CDRom to "use system cdrom" 3. tried to enable the VMWare tools but it complained that the vm was in "Easy Install" mode After I fiddled with the VM now my floppy and 2 CD rom devices as well as sound card and USB settings are all disabled in the VM hardware settings. Any idea on why this occurred and how to fix it?

  Read the article

< Previous Page | 192 193 194 195 196 197 198 199 200 201 202 203  | Next Page >