Search Results

Search found 6324 results on 253 pages for 'nathan fast'.

Page 197/253 | < Previous Page | 193 194 195 196 197 198 199 200 201 202 203 204  | Next Page >

• Why does my simple Raid 1 backup storage perform really slow sometimes?

  - by randomguy

  I bought 2x Samsung F3 EcoGreen 2TB hard disks to make a backup storage. I put them in Raid 1 (mirror) mode. Made a single partition and formatted it to NTFS, running Windows 7. For some reason, accessing the drive's contents (simply by navigating folders) is sometimes really slow. Like opening D:/photos/ can sometimes take several seconds before it starts showing any of the folder's contents. Same applies for other folders. What could be causing this and what could I do to improve the performance? I remember that there was an option somewhere inside Windows to choose fast access but less reliable persistence operations (read/write). It was a tick inside some dialog. At the time, it felt like a good idea to take the tick away from the option and get more reliable persistence but slower access, but now I'm regretting. I'm unable to find this dialog.. I've looked hard. I don't know, if it would make any difference. Oh, and I've ran scan disk and defrag on the drive. No errors and speed isn't improved.

  Read the article

• Application that will identify percentage of your system disk bandwidth used on a user-application by user-application basis?

  - by Warren P

  I always (subjectively) feel my computer is far too slow (however fast it is), and so I'm always looking for ways to measure and understand what my computer is actually doing, that is making it seem "slow" to me. It has been my observation that my software-developer workload is most often disk-bound (I am waiting for Disk I/O) more than CPU bound. What has made it worse, is that I am using a corporate PC that has in-memory active-scanning anti-virus software that I do not have control over, and also some IT department mandated services that seem to suck up a lot of available hard-disk bandwidth. The best tool I have seen (in Windows 7) is the Resource Monitor which I usually acess from the button in the task Manager. The disk IO page, however, seems to label Disk Activity at a very low level (for example, showing the Volume Shadow Storage, which is flushing information obviously written by something ELSE other than VSS itself, and then writes to Pagefile.sys, which are obviously due to Virtual Memory faults in some application). What I would like to know is if a utility exists that can add up all direct disk input and output by user-level process, or find the process or service that caused VM or VSS activity. In that way, I hope, you could establish a real idea of how much of your computer's precious disk subsystem bandwidth is attributable to a particular application. here's a scenario: MyApp.exe writes 100k/s and reads 100k/s directly. VSS ends up writing another 100k/s. pagefaults caused inside MyApp.exe cause another 100k/s of writes. So the total "cost" of MyApp.exe running, during a period of time (let's say 1 second) is 400k/s, whereas you can only directly observe half of that, in Resource Monitor. Is there a smarter disk-IO watching piece of software I can use?

  Read the article

• Windows Server 2008 IIS7 - page requests randomly hang or timeout

  - by seb835

  I've just installed a fresh copy of Windows Server 2008 x64 with IIS7 and PHP (fast CGI). However, I'm noticing that after moving my web site from a similarly specified machine to this one, I'm getting issues. The issue seems to be that randomly, as I'm clicking through the web pages being served, the browser will suddenly hang saying "waiting for mysite.com...". Sometimes the page will then timeout, or finally resolve after 20 to 30 seconds, but maybe missing the CSS style sheet. Very strange, as this is the only website installed on this new server, and only myself using/testing it. Server is installed in the same data centre below the old server. Has anyone else had a similar problem? I tried increasing the max workers pool to 10 (from 1), but this has no effect. Seems to happen most frequently after 1 or 2 minutes of inactivity on the website, then trying to load/refresh a web page. Many thank for any info and help. Kind Regards, Seb

  Read the article

• Skipping nginx PHP cache for certain areas of a site?

  - by DisgruntledGoat

  I have just set up a new server with nginx (which I am new to) and PHP. On my site there are essentially 3 different types of files: static content like CSS, JS, and some images (most images are on an external CDN) main PHP/MySQL database-driven website which essentially acts like a static site dynamic PHP/MySQL forum It is my understanding from this question and this page that the static files need no special treatment and will be served as fast as possible. I followed the answer from the above question to set up caching for PHP files and now I have a config like this: location ~ \.php$ { try_files $uri =404; fastcgi_cache one; fastcgi_cache_key $scheme$host$request_uri; fastcgi_cache_valid 200 302 304 30m; fastcgi_cache_valid 301 1h; include /etc/nginx/fastcgi_params; fastcgi_pass unix:/var/run/php-fastcgi/php-fastcgi.socket; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /srv/www/example$fastcgi_script_name; fastcgi_param HTTPS off; } However, now I want to prevent caching on the forum (either for everyone or only for logged-in users - haven't checked if the latter is feasible with the forum software). I've heard that "if is evil" inside location blocks, so I am unsure how to proceed. With the if inside the location block I would probably add this in the middle: if ($request_uri ~* "^/forum/") { fastcgi_cache_bypass 1; } # or possible this, if I'm able to cache pages for anonymous visitors if ($request_uri ~* "^/forum/" && $http_cookie ~* "loggedincookie") { fastcgi_cache_bypass 1; } Will that work fine, or is there a better way to achieve this?

  Read the article

• PXELinux and compressed kernels/images

  - by Yvan JANSSENS

  Is it possible to boot compressed kernels with a compressed initrd with PXELinux? First, a little background: We created a custom Linux distro, for diskless OpenCL computing nodes. We want those nodes to fetch their OS from the network. Our Distro is composed out of a kernel (duh) and a large initrd which is loaded into RAM and everything is executed from there. We chose to run everything off the initrd for two reasons: NFS was not an option to serve the filesystem's extra contents Fast file access from RAM. No persistent storage needed, data and config is pulled dynamically through a SOAP service. Now our initrd is about 450M in size. At our network speeds, it takes about two to three minutes to load a single client. Will compression speed up te downloading, and if yes, which one should be used? Is LZMA supported by PXELinux, or do we need to stick to bzip2 or gzip? Because of the 2-3 minutes loading time, booting 15 nodes over the same network link takes quite a lot of time. We decided not to use hard drives or CD/DVD drives, for financial reasons (cheapest HDD @ €30 times 15 is a lot of money saved ;-) ) So, our question is: what compression options are available for this setup? And how do we do this? Thank you for your time! Yvan Janssens

  Read the article

• What is the fall off of subsecond throughput on Ethernet Network Interfaces

  - by Kyle Brandt

  On a network interface, speeds are given in term of data over time, in particular, they are bits per second. However, in the uber-fast world of computing -- a second is kind of a really long time. So for example, given a linear falloff. A 1 GBit per second interface would do 500MBit per half second, 250Mbit per quarter second etc. I imagine at certain units of time, this is no longer linear. Perhaps this is set by ethernet frequencies, system clock speeds, interrupt timers etc. I am sure this varies depending on the system -- but does anyone have more information or whitepapers on this? One of the main reasons I am curious is to understand output drops on interfaces. Even if the speed per second is much lower than the interface can handle -- perhaps there are spikes that cause drops for only small numbers of milliseconds. Perhaps various coalescing would hide this effect -- or perhaps increase it on the receiving interface? Do queues make a difference here? Example: So given if this is linear down to the MS we would have 1Mbit/MS, and if Wireshark isn't distorting what I see, should I see drops when I have a spike beyond 1Mbit?

  Read the article

• What mobile phones are viable for a "nerdy" person? [closed]

  - by Blixt

  This community wiki is for determining a list of good mobile phone choices if you are "nerdy" (definition follows.) As a point of reference, the almost two years old N95 8GB will be used. Mostly because that's what I can most relate to since I've had it since it came out. Today, iPhone and other modern mobile phones really out-shine it in usability and interface. However, it still does everything I want it to do (and here's the definition of "nerdy"; modify as needed): Syncs contacts, calendar, tasks and mail in the background Can run multiple installable applications in the background (Google Maps with Latitude, for example) Good amount of space for music etc. Lets you develop your own little toy applications (Python; not to mention it can also run an Apache server with a public URL!) Tethering! Supports Flash (maybe not very important, but it has its uses) Has a manufacturer that believes in the nerdiness! (The people at Nokia Labs make lots of cool stuff and share early versions with the community and are generally open) A high resolution screen (at least 320x240) Special hardware features such as an accelerometer and GPS What's missing from the N95 8GB but still qualifies as good, "nerdy", qualities: 7.2 Mbit/s (or faster) internet through HSDPA or HSPA+. A good web browser that can do most of the stuff a desktop browser can (especially render sites properly and run JavaScript correctly) Touch (especially multi-touch) More special hardware features such as a compass Intuitive and fluent user interface (Shiny stuff) Ability to configure it to trust root certificates of my own choice A processor fast enough to run Quake 3! =)

  Read the article

• Does a high run queue length average result in poor performance for a web server?

  - by Domino

  I'm trying to narrow down the list of suspects of web servers that perform moderately well most of the time with occasional bouts of poor performance. I'm analyzing the data collected and summarized by sar. I've noticed a few things, one of which is high number of tasks in the run queue. 10:15:01 AM runq-sz plist-sz ldavg-1 ldavg-5 ldavg-15 blocked 10:25:01 AM 2 150 0.05 0.05 0.06 0 10:35:01 AM 4 149 0.08 0.12 0.09 0 10:45:01 AM 6 150 0.13 0.19 0.15 0 10:55:01 AM 1 150 0.08 0.10 0.13 0 11:05:01 AM 4 150 0.20 0.35 0.23 0 11:15:01 AM 3 149 0.02 0.09 0.15 0 11:25:01 AM 7 149 0.04 0.05 0.11 0 11:35:01 AM 4 150 0.14 0.15 0.13 0 11:45:01 AM 6 150 0.27 0.18 0.16 0 11:55:01 AM 5 150 0.08 0.10 0.13 0 12:05:01 PM 3 149 0.35 0.40 0.26 0 12:15:01 PM 19 155 0.02 0.10 0.16 1 12:25:01 PM 2 150 0.00 0.07 0.12 0 12:35:02 PM 3 151 0.58 0.24 0.17 0 12:45:01 PM 8 150 0.02 0.13 0.15 0 12:55:01 PM 6 149 0.81 0.29 0.18 0 01:05:01 PM 3 148 0.00 0.09 0.13 0 01:15:01 PM 7 149 0.00 0.04 0.11 0 I believe these are 10 minute averages. Is this an indicator that the web server is not performing as fast as it could if the average run queue length was lower?

  Read the article

• How to optimize a postgreSQL server for a "write once, read many"-type infrastructure ?

  - by mhu

  Greetings, I am working on a piece of software that logs entries (and related tagging) in a PostgreSQL database for storage and retrieval. We never update any data once it has been inserted; we might remove it when the entry gets too old, but this is done at most once a day. Stored entries can be retrieved by users. The insertion of new entries can happen rather fast and regularly, thus the database will commonly hold several millions elements. The tables used are pretty simple : one table for ids, raw content and insertion date; and one table storing tags and their values associated to an id. User search mostly concern tags values, so SELECTs usually consist of JOIN queries on ids on the two tables. To sum it up : 2 tables Lots of INSERT no UPDATE some DELETE, once a day at most some user-generated SELECT with JOIN huge data set What would an optimal server configuration (software and hardware, I assume for example that RAID10 could help) be for my PostgreSQL server, given these requirements ? By optimal, I mean one that allows SELECT queries taking a reasonably little amount of time. I can provide more information about the current setup (like tables, indexes ...) if needed.

  Read the article

• System With Two Network Adapters [closed]

  - by Synetech inc.

  Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

  Read the article

• Fans still running after shutdown after upgrade to Windows 8

  - by docaholic

  I'm running into a really annoying issue after upgrading from Windows 7 to Windows 8. I first noticed it during the initial (clean) install; when the installer tried to reboot, my machine (an acer aspire 4755G) just hung after the initial shutdown. That is, after the screen turns off, the power lights and fans are still running, and the machine itself doesn't restart. (I let it sit for a good 15 minutes, and it still didn't change) I managed to do a hard reset (power button for 5 seconds) and the install finished, but every shutdown/restart has been like that. Interestingly enough, hibernate works just fine. I've looked at other solutions where it said to use the bcdedit /set disabledynamictick yes and that didn't work. I also turned off the "Fast Boot" option in the power settings menu. That didn't work either. So far, the only option is to do the hard shut down by holding down the power button, but that proves to be horribly inconvenient. Any ideas on what's going on here?

  Read the article

• Fake demostration software for command line

  - by Joe

  I'm looking for some software that would be useful for giving demonstrations. I regularly have to show the effects of scrips ect to classes while talking about their effects, and equaly regularly I have finger trouble and have to rewrite various commands - wasting class time and general energy. I'd like to be able to record a sequence of commands in advance, and then play them back at the speed of my choosing. So I might have a file that containes the commands: echo "hello world!" ls ls -l ls -l | sort I'd like to be able to play these commands back by typing similar ones in. So I'd have a blinking command prompt and if I typed 'echo "hxxx' the command prompt would read home$echo "hell and if I typed any other letters the terminal would fill up with the remainder of the command until I press enter, when it executes the command. The point is that even if I screw up the command when typing it, the command that I'd prepared in advance would be executed. My question is - does similar software exist for giving demonstrations? or even, is this an easy thing to script up...? EDIT - two quick things first of all I'm on osx - but it would be nice to get a general solution for other people who arrive here from google. and second a lot of the comments/answers are concentrating on, in effect, making it fast and easy to enter long commands by means of hotkeys and the like. Actually I'd like it to at least look like I'm typing live - that's why I put in the bit about the one-to-one keymapping, but I don't think I explained that quite as well as I could have...

  Read the article

• XBMC remote control key repeat

  - by Amigable Clark Kant

  Those who have used XBMC with a WiFi remote, such as an Android or iOS device with the official XBMC remotes, have probably seen this at one time or another: your remote stops working, when you press a key, that key is repeated very fast. Sometimes you can break the key repeat loop by pressing that same key again. Sometimes (as this particular morning) you can not. This problem has existed for literally years (it even occurs on the old XBOX only builds) but there seems to be no definite explanation as to what is causing it. I am asking for a workaround. (If you Google, you can find threads were people are ridiculed for bringing up this problem, which is one reason I ask here instead of on the official forums. Also the fact that this problem has persisted for so many years.) I am running, right now, XBMCBuntu Live Eden and the latest official iOS remote. Although, I have seen this problem on all combinations of remotes and XBMC versions I have tried over the years, which are many. (XBMC on Windows, Linux, OSX, remotes on Android and iOS.) Link to bug #136 for the Android remote. It's marked as "fixed" as of client version 636, but the problem is seen again in rev 730. Go figure. There is something fundamentally wrong with how keypresses are sent from the various remotes to XBMC, since this problem is seen across time, XBMC versions and iOS/Android.

  Read the article

• Network card shuts down when stressed

  - by user142485

  I have a network card that functions fine with light use, but quits functioning after heavy use. I replaced it with a brand new one and still have the same issue, also updated drivers. It is a wired D-Link card. The Internet seems fine for a small amount of web browsing but when I run a bandwidth test it starts out fast and slows quickly until the card completely quits; I have a constant ping of the gateway going while I run this and it starts timing out after a couple seconds into the speed test. The card will stay on and the data light on it still flashes some but I cannot ping the gateway or anything else until the computer is rebooted. When I boot into safe mode I can browse and run the speed test fine with no problems. I am guessing that this is probably some program that is loading in regular mode but not safe mode that is causing the issue? I have very limited software (turned off av and firewall) on the computer but I am thinking that I'll just have to start eliminating start-up programs and see if that helps. This is on Windows 7 if that makes any difference. Anyone had a similar issue or have any other suggestions/ideas for narrowing down this problem?

  Read the article

• Ubuntu + LigHTTPd: Server requests taking ages

  - by ctrl_freak

  I've had an issue since upgrading my distro a couple of weeks ago from hardy; receiving data after making a request has increasing intervals of nothing, as you can see from the picture below. http://i49.tinypic.com/2w5lvr9.png I have since reinstalled fresh from an Ubuntu 10.04 Server (i386) disk, but am still having the same issues. I'm running on a LigHTTPd, MySQL, PHP5 stack. The surprising thing is, that local browsing using lynx is super fast, as expected. Initially, after reinstalling, I copied over the old configuration files from the previous installation, but have since reinstalled LigHTTPd and rebuilt the config file from scratch. The only correlation I could find, was that I attempted installation of ionCube and Zend Optimizer for a script I was testing, however I would think that it could no longer impact seeing I had reinstalled the OS. I have also removed Suhosin just in case, however it had no impact. I'm thinking it possibly has something to do with networking, but I wouldn't know where to start. The server is manually assigned an IP by it's MAC address on the router. The fact that the time seems to be exponential (to a point) worries me. I've tried strace'ing the LigHTTPd and MySQL processes, however I couldn't see anything obvious, not that I'd really know what I'm looking for. RAM and CPU usage don't seem to be out of the ordinary, but I can't say its perfect.. I'm hoping someone has experienced the same, or can point me in a direction, as searching has proved fruitless as I don't know anything specific. Config files can be posted, if requested.

  Read the article

• Cannot change power button or lid close action

  - by Mark Henderson

  I have a Samsung 900x laptop and I want to change it so that when I close the lid, nothing happens (I often close the lid to carry it somewhere 10 seconds away, and by putting it into suspend it cancels any active downloads/etc). Easy, right? Go to Power Options and change it there; just like on every other laptop in the world. Not so fast: Saywhat?! That message only shows up for the nodes for Lid Close Action, Power Button and Sleep Button. I can change every other setting except for those three. I'm definately an Administrator on the computer, and I've googled the error and found dozens of hits on other crappy forums, but of course nothing on those worked (otherwise, I wouldn't be here). And as ususal the "Why can't..." hyperlink gives no useful infomation what so ever (just a generic Help document). So - how can I change what closing the lid does? I will modify the registry directly if I have to.

  Read the article

• Apache Virtualhost entry with Windows hostname

  - by gshauger

  I have a Windows Domain Controller and we use it for DNS for our internal network. I have an Ubuntu box with an IP address of 172.16.34.149. Within the Windows DNS I created the forward and reverse lookup entries for the name Endymion. Naturally when ever I FTP/SSH/HTTP/etc to the hostname Endymion it resolves correctly to my Ubuntu box. I wanted to do some web development on this box for an existing site. There were problems when I placed the website in a subfolder of /var/www/. Let's just say it was in folder /var/www/projectx/. The issue involved the incorrect resolution of non-relative urls. So I figure I could create a new DNS entry for the hostname projectx. Sure enough when I FTP/SSH/HTTP/etc to the hostname projectx it takes me to the same ubuntu box as the hostname Endymion...this is what I would expect. I now have two hostnames for the same box. I then create a Virtualhost entry in httpd.conf that looks like the following: <VirtualHost *:80> DocumentRoot /var/www/projectx ServerName projectx ServerAlias projectx </VirtualHost> Sure enough when I go to a browser and type in http://projectx/ it takes me to the correct subfolder. Everything works!!! Not so fast. I then go to http://endymion/ and instead of taking me to /var/www/ it takes me to /var/www/projectx/ Clearly I'm missing something. Help please! ;)

  Read the article

• Is there a local yubnub.org replacement?

  - by Justin Keogh

  I use yubnub very often... every google search I do by just (in firefox) "ctrl-t" - (now in the url bar) "y g searchterms" [Enter] "y" in this case is a search keyword I added by right clicking in the yubnub.org command box it's really fast, and I just do it automatically now... but the problem is now I am stuck with whatever the yubnub command that I am so used to using does. I cant change it... for example, what if I dont want to use google... but I still want to use the "g" command to search? or say I want to use google's https search... ect... I suppose this would be kinda trivial to implement locally... but I would hate to re-invent the code if it's allready done and in use... ideas? Also a local yubnub.org replacement would save me the DNS lookup and traffic to yubnub.org. I dont expect to be able to import all commands from yubnub.org but that would be cool if possible.

  Read the article

• Ubuntu inside VirtualBox is slow

  - by Kapsh

  I am running an Ubuntu instance on VirtualBox inside XP. Here are the details: Host: Windows XP Pro Guest: Ubuntu 8.10 Total RAM: 3GB RAM For VM: 1GB Total Video Memory: 128MB Video Memory for VM: 40MB Hard Drive: 200GB Hard Drive for VM: 30GB Processor: 2.80GHz Core Duo The problem is that whenever I am inside the virtual machine, things seem so much slower in general. For example Firefox, Eclipse take longer to load, dragging windows show a lag etc. I have tried running Ubuntu before (not inside a VM) and it seemed fantastically fast. So I am disappointed to have to deal with this situation. But I need access to the XP partition without having to reboot and hence the attempt. I am surprised with the perceived slowness since the whole world seems to be doing virtualization and I cannot imagine everyone works on slow systems knowingly. My question is - is there something I should be doing to boost performance? Am I doing something wrong? This is my home machine and I am not sure if this is the right forum to ask. Thanks.

  Read the article

• Recover data from hard drive with partitions (but not most data) overwritten

  - by Macha

  I have a 500GB hard drive I've been keeping around to recover data from that I removed from a failing NAS drive that got sort of... erratic at the end. I finally got rid of the NAS when during a firmware update it removed the partition table. Fast forward to a week ago, when I was building a new PC, and a mixup resulted in me placing the hard drive in question in the new PC and installing Windows XP on the first 100GB. I'm presuming any data on that first 100GB is now gone, but for the rest of it, is there any way I can recover it at home, as professional data recovery is currently too expensive? I have a blank 1TB HDD if I can store any images of that hard drive on. The problem was definitely with the NAS and not the hard drive, as the hard drive had a successful install of Windows when mistakenly place in the new PC, and there were capacitors in the NAS's circuitry clearly broken. The data I want to recover (in order of priority) is: High: Some jpgs of family photos. Medium: Some RAW files. (There are also jpg versions of all of these) Low: Some mp3s, avis and ISOs, I can re-rip most of these if need be, but it'd be handy not to have to. (I don't need a backup lecture, and if you can hold it in from nagging Jeff Atwood for it, you can hold it in from nagging me for it) In short: The partition tables are gone and overwritten. The data is not overwritten, except for an amount equal to the size of a Windows XP SP3 installation.

  Read the article

• Windows 8 not shutting down properly

  - by Patrick

  Since installing Windows 8, the computer hasn't been shutting down properly. When selecting to power down, the PC quickly displays the shutting down screen, the monitor powers off, and the computer remains on but unresponsive. After about 5 minutes, the computer will turn off. Upon booting into windows again, I am informed that Windows didn't properly shut down. I'm running a fast SSD, and it's a clean install of Windows 8, so there's no way Windows is taking that time to do some sort of hibernate on shutdown or whatever - not to mention the error when entering Windows the next time. This happens on every shut down. Restart works as expected. EDIT: Formatting again didn't work. Fails regardless of drivers installed. Event viewer Always these two messages in close succession: Error (event ID 6008): The previous system shutdown at 7:45:21 PM on ?27/?10/?2012 was unexpected. Critical (kernel power, event ID 41): The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly.

  Read the article

• Why is my new PC so slow at startup?

  - by rumtscho

  Bought a new PC this weekend, and it works really good. Only I have one big problem: startup time. Its BIOS needs 62 sec to load, then from Grub start to pw entering screen it's another 26 sec. I think this is a lot, because my old PC needs 34 sec for BIOS and another 8 sec to pw screen. After I enter the pw, the desktop is usable with practically no delay on both. The new PC is a core i7-930, running a Lucid Lynx 64 bit from a Intel Postville SSD (no internal HDs). The old PC is a Pentium 4 celeron (forgot the clock speed) running a Lucid Lynx 32 bit from an ATA 100 hard drive. Neither PC is overclocked. The new one has boot sequence 1.DVD ROM, 2.SSD (connected over SATA in AHCI mode), 3. removable drive. The old one boots from 1. DVD ROM, 2. HDD, 3. Floppy. Neither has a second OS installed. The new one has less software installed than the old one (I think), but the boot time difference was noticeable even before I made any installs. As far as I know, just the SSD should be enough to make a noticeable difference in boot time. I thought that having a good mainboard on the new PC as opposed to the basic office model on the old one would also mean a faster loading BIOS. If these assumptions are right, I guess I must have misconfigured something in the BIOS of the new PC. How should I configure it for a fast boot? It has an ASUS P6X58D board with an AMI BIOS, if you need the BIOS revision number I could post that too.

  Read the article

• What is the best hosting option for Flash web-widget?

  - by par

  Our Flash web-widget has got highly popular. It is downloaded around 100,000 times per day. And that is the problem. Our server bandwidth is too narrow to deliver the widget to the clients fast. The widget is loaded very slow. Probably 20 times slower than before (at peak times). Probably I have choosen not the right hoster for my task - delivering 1 MB Flash widget to 100,000 users per day. What is the best hosting solution in my case? I'm not good at server administration so forgive me if I sound naive. The details are the following. Our hoster options: -Dedicated server, Ubuntu -10 Mbit Connection -monthly bandwidth limit: 2000 GB Widget size is 1 MB. The widget consists of the main SWF and a number of loaded SWF and data files. This is a part of Apache Status report taken right now ---- Server uptime: 1 hour 2 minutes 38 seconds Total accesses: 74865 - Total Traffic: 5.8 GB CPU Usage: u28 s7.78 cu0 cs0 - .952% CPU load 19.9 requests/sec - 1.6 MB/second - 81.1 kB/request 200 requests currently being processed, 0 idle workers WWWWWWWWWWWWWWWWWWWWWWWWCWWWWWWWWWWWWWWWWWWWWWWWWWWCWWWWWWWCWWWW WWWWWCWWWWWWWWWWWWWWCWWWWWWWWWWWWCWWWWWWWWCWWCWWWWWWWWWWWWWWWWWW WWWWWWWWWWWWWWWWCWWWWWWWWWWWWWWWWWWWWWWWWWWWCWCWWWWWWWWWWWWWWWCW WWWWWWWW........................................................ ----

  Read the article

• How to fix Windows 7 when System Recovery Options hangs?

  - by seansand

  The battery power ran out on my HP G60 laptop and it shut down. Even after recharging, Windows 7 will now not start up. After any attempted startup, it bluescreens and takes me to the "Startup Repair (recommended)" / "Start Windows Normally" console screen. "Startup Repair (recommended)" appears to be the right choice, but when I choose it, I get taken to a screen which appears to be System Recovery Options (it's the same wallpaper as the screenshots here: http://www.sevenforums.com/tutorials/668-system-recovery-options.html). However, I just get a cursor with nothing else; no "System Recovery Options" window ever pops up. (A black console screen does pop up for a split-second but too fast to be able to read the text.) The empty screen with cursor hangs indefinitely. System Recovery Options normally runs off of a partition on the laptop hard drive. When I got the laptop, I also created a System Repair Disc (in fact I have more than one) and when I try use any of them; they all result in the same wallpaper and empty screen with lone cursor. Ctrl-Alt-Del does nothing. The computer did not come with a Windows 7 installation disc, so there's no obvious way to reinstall Windows 7. Safe mode does not work; startup fails and I just get sent back to the "Startup Repair (recommended)"/"Start Windows Normally" console screen. "Start in last good state" does not work either, same result as above. Running a memory & hard disk check found no errors. Do I have any options at all? "System Recovery Options" seems to be what I want, but the screen that is supposed to take me to them just hangs.

  Read the article

• MySQL : table organisation for very large sets with high update frequency

  - by Remiz

  I'm facing a dilemma in the choice of my MySQL schema application. So before I start here is a picture extremely simplified of my database : Schema here : http://i43.tinypic.com/2wp5lxz.png In one sentence : for each customer, the application harvest text data and attached tags to each data collected. As approximation of the usage of each table, here is what I expect : customer : ~5000, shouldn't grow fast data : 5 millions per customer, could double or triple for big customers. tag : ~1000, quite fixed size data_tag : hundred of millions per customer easily. Each data can be tagged a lot. The harvesting process is permanent, that means that around every 15 minutes new data come and are tagged, that require a very constant index refreshing. A lot of my queries are a SELECT COUNT of DATA between specific DATES and tagged with a specific TAG on a specific CUSTOMER (very rarely it will involve several customers). Here is the situation, you can imagine with this kind of volume of data I'm facing a challenge in term of data organization and indexing. Again, it's a very minimalistic and simplified version of my structure. My question is, is it better: to stick with this model and to manage crazy index optimization ? (which involves potentially having billions of rows in the data_tag table) change the schema and use one data table and one data_tag table per customer ? (which involves having 5000 tables on my database) I'm running all of this on a MySQL 5.0 dedicated server (quad-core, 8Go of ram) replicated. I only use InnoDB, I also have another server that run Sphinx. So knowing all of this, I can't wait to hear your opinion about this. Thanks.

  Read the article

< Previous Page | 193 194 195 196 197 198 199 200 201 202 203 204  | Next Page >