Search Results

Search found 12013 results on 481 pages for 'dvd drive'.

Page 201/481 | < Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >

• Windows XP , HP , IntelInside Trobelshooting

  - by Jamil Hneini

  My Windows XP PC has stopped booting. On start up, before Windows boots a screen appears saying: Windows Could Not Boot: Could Not Find or Corrupted file <Windows root>\Sytem32\Hal.dll Please Reinstall the file... From that I understand that I have to reinstall the OS but my computer is so old that I have lost the backup and recovery disk. My Computer's Info: 32Bit Computer Pentium 4 Windows XP Service Pack 2 HP History: My Computer has 4 hard drives 2 internal 40 GB drives (C And D) 2 external 8GB drives (E And F) Additional Info: I need the files inside C And E The computer reads my flash drive as a hard drive (8.45GB)(I have never booted while my USB pluged in while I was troubleshooting) With some test I discovered that the C drive wasn't detected by the computer I have already configured the boot order of BiOS I have Set The SATA to IDE The Question: I have a setup for windows 8 32 bit how can I boot from my USB to run that setup? If that isn't the proper way to handle this problem please tell me the proper way.

  Read the article

• Losing partitions after every reboot

  - by Winston Smith

  I have an Acer laptop with one hard disk, which up until yesterday had 4 partitions: Recovery Partition (13GB) C: (140GB) D: (130GB) OEM Partition (10GB) I read that the OEM partition has all the stuff needed to restore the laptop to the factory settings, but since I'd already created restore disks and I needed the space, I wanted to get rid of it. Yesterday, I used diskpart to do that. In diskpart, I selected the OEM partition and issued the delete partition override command which removed it. Then I extended the D: partition into the unused space using windows disk management. Everything worked fine, until I rebooted my laptop, at which point the D: drive vanished. Looking in windows disk management again, I can see that there's an OEM partition of 140GB, which is obviously my D: drive. So I used EASEUS Partition Master and assigned a drive letter to the 'OEM' partition and I was able to access my files again. However, every time I reboot, it reverts back. How do I fix this permanently?

  Read the article

• broken partition possible for recovery?

  - by claw

  I was using copywipe on hirens boot cd to copy a Windows installation to a new drive. unfortunately for me, I was rushing, I set the source drive as the USB drive running hiren/copywipe to the Windows partition, I think it has destroyed the partition tables and replaced with hiren boot USB ones. disk: was NTFS 40 / 250 partitions disk: now FAT32 145 / 145 partition I have used several partition recovery tools, diskdigger to name one, they all show a recovered partition, but its the hiren stuff. any advice would be a fantastic help To all that have similar issues I recommend using TestDisk (undelete partition) software. you can get this software as part of hirens boot cd. see answer

  Read the article

• Network backup for Macs and PCs - formatting question

  - by neilfein

  I'm trying to use a LaCie 2TB drive as an AirPort drive, for backup on a home network. We have one mac and two PC laptops. My plan is to create a Mac partition and a Windows partition. However, Disk Utility won't let me set the windows partition to Windows format; there's no option in the menu for it in the partition tab. Am I doing something wrong? Alternatively, is there a way to partition the drive with one partition that all three machines can see? We have a Mac G5 with 10.4 and two laptops with Windows 7. Thanks!

  Read the article

• Accessing a shared folder using other credentials with Windows 7

  - by Nicolas Buduroi

  I was at a client office trying to connect to a shared drive on their network but was greeted by a "you do not have permission to access" error! Couldn't find any way to enter the required credentials as this message didn't had any other options. Tried to map the drive, selected the option to enter the correct credentials (with \\HOST\user) but it wouldn't work at all. The worst thing in all of this is that my coworker who is using OS X has been able to connect to that drive without any problem, he clicked on it, entered the credentials and could open the folder! The folder is shared by a Windows Small Business Server 2008 machine.

  Read the article

• Offset AND incremental backup

  - by Pyrolistical

  I already do backups from my main computer to my server computer using synctoy. But now I also want to do off-site backup. My idea so far: have source hard drive (we'll call S) at home have backup hard drive at work called B have transport hard drive called T connect T at work and record index of files on B take T home and check index of S and note new/changed/deleted files and copy changed files to T take T to work and update S repeat Its basically a sneakernet and using all of the advantages of it. High bandwidth, low latency. Is there some software to do this, or do I have to write it myself?

  Read the article

• Missing disk space in Windows XP

  - by Jørn Schou-Rode

  On my mother's Lenovo laptop, Windows XP claims that the hard drive is almost full. According to the properties window, 52.7 out of 55.2 GB is in use: By deleting temp files from Internet Explorer, System Restore, Recycle bin, Windows Update, System Cleanup, I managed to free up about one GB. That's still 50 GB in use, which still is a lot more than I expected. Hence, I gave good old WinDirStat a spin, and here's the output: It might be hard to read here, but the first line says that the total amount of disk space in use on drive C is 24.3 GB. So Windows claims usage of 52.7 GB and WinDirStat can only account for 24.3 GB. Where is the other half of that disk space being used? I hope someone has an answer, or some tricks or tips to do further research. UPDATE: The laptop in question has an SSD hard drive. I am aware that these disk (at least the earlier ones) have a limited life-time. Could the symptoms described be caused by wear and tear on the SSD?

  Read the article

• Subversion for web designer: repository on a network share and ftp to the live server?

  - by ceatus

  My configuration: htdocs on a windows network share (z:) web developers check out with dreamweaver modify and check in back to the drive z LAMP running on a Ubuntu server virtualized on Hyper-V with apache that point on the z drive for dev in order to test the websites Upload by FTP on the live server Now: I need multiple access to the repository, keep them on a network shares and we manage about 200 websites. All the web developers, administrators and IT need to access to the share. I found out that creating a svn server is the best way for me, so I created it on a Ubuntu Server which is virtualized on Hyper-V. Right now I have the repos local on the Ubuntu Server but I'd like them on my network drive and I'd like to have a post-commit, if possible, in order to ftp directly on my live server. Do you guys think that a WebDav solution would be better? Thanks in advance Angelo

  Read the article

• Setting up Raid 1 Array for Home Server

  - by user1048116

  I'm not sure if this is even possible, but it's worth asking on here! Essentially I have a old machine at home (well, not old hardware wise, but I recently built a new gaming rig), which I decided to install a copy of W2008 R2 on and use as a file/backup server and media center'ish machine. As of now, it has a single drive partitioned into C and D, with D being the Data partition. I have happened to find an old 1TB SATA drive lying around at home, and was wondering if it's possible to setup a Raid 1 array in my rig within Windows without needing to lose everything on my first drive (or maybe even just mirror a specific partition, say the Data partition, as this is just what stores my photos etc). Maybe this isn't possible, but you never know :) Regards, T.C

  Read the article

• HP DL370 G6 expansion

  - by user72185

  Hi, we are running a HP DL370 server with 6 x 300 gb disks on RAID 5. Due to a Windows update causing our server to fail recently, we couldn't access the data. I now want to separate the data from the OS (Windows server 2008 r2) so that if anything like that happens again, we can route everyone through a separate server. I have seen these HP storageworks enclosures (msa70) and have a couple of questions: Can I just take out our 2.5 inch 10k SAS drives, install them in the new Storageworks NAS and hey presto we would be up and running? If I wanted to then add another drive (I think there are 25 bays), can I just insert a blank but identical drive and the RAID 5 would dynamically expand to incorporate the new drive. Many thanks Adrian

  Read the article

• SharePoint Designer not syncing consistently

  - by normalocity

  I've got a user who uses SharePoint Designer to maintain an internal intranet site. When syncing (remote-to-local) it appears to work at first, but usually hangs about 2-3 minutes into the sync, when he's syncing it to a sub-folder of his "My Documents". In this case, his "My Documents" is stored on a network share/profile. When I do the same thing, it works for me. The difference? My "My Documents" folder is locally stored. In other words, he's syncing from the remote server, into a network share. I'm syncing from the remote server, into a local drive. Any idea why having the sync destination on a network share, vs. a local drive would cause this? When it locks up, we can navigate to his "My Documents" folder still - so I don't believe that we're loosing connection to his drive - unless perhaps the connection is intermittent, and SharePoint Designer isn't re-trying the sync.

  Read the article

• Cloning a linux system from sdx to cciss

  - by churnd

  I have an HP ML 310 server running CentOS Linux 5.5. I'm buying a RAID card (LSI 9260-8i) to set up a mirrored OS drive. Right now, the boot drive is set up with GRUB installed on the MBR of /dev/sda & has a 100MB /boot partition for /dev/sda1, then the rest is configured in LVM with a 20GB with a 20GB VG for the root partition & ~80GB VG for home. The new disk sizes will also be slightly larger as well. What is the best way to clone the boot drive to the new CCISS device?

  Read the article

• How do you passthrough native SATA drives to a guest on ESXi?

  - by John

  I have ESXi 4.0 running on an Intel DX58S0 Mothboardboard with an Intel Core i7 930 processor. VT-d is also enabled. I have three drives in the system, drive 0 is used for ESXi. Drive 1 and 2 contain data from an older machine and show up under the "Storage Adapters" section in configuration. I would like to allow a guest machine to access the data on these drives (as nativly as possible). I have enabled passthrough of the motherboard's built in SATA controller (Intel/Marvell 88SE6121 ). This controller shows up in my guest OS, but the guest shows no drives aside from the normal virtual drive. I have tried a Linux guest and Windows7. I have also configured the host machine to try IDE/RAID/ACHI modes for the SATA controller. Any ideas how I can configure one of my guests to get at the raw data on these drives?

  Read the article

• Mac OS x 10.4 Tiger Will Not Boot

  - by keithbrown38

  My G5 Tower all of a sudden is ONLY booting to the Registration page, the where after you installed the software you are suppose to Register. I cant get it to boot in safe mode, so I am using my usb 2.0 SATA cable to connect my drive to a my macbook pro and I am using (CCC) Disc to Disc Clone and it is copying to my external WD passport drive and that makes a startup disc along with all my info from my drive. My question is was there anything easier and less time consuming than that? Does anyone know why this would happen all of a sudden? Thank You All in Advance for your help and support! Keith B

  Read the article

• How to set up a PC which can be booted from Linux AND Windows?

  - by Martin

  Our PC was running Windows XP up to know. It has become incredibly slow and I'm considering switching to Linux (Ubuntu?!) as a fresh OS. However, there are some applications we rarely use which run only on Windows and I also want to have the possibility to easily go back to the old system, if I should find during testing linux, that anything is missing or not available. So the idea is to install Linux on a new (second) hard drive and use the existing Windows XP from a virtual machine (converted by Paragon Drive Backup) in the transition time. We have a lot of data on the PC, tens of GBs of Photos (managed by Picasa), ... My questions: What could be the best way to setup the new hard drive? (Partitions) I assume that I can not access the Linux data from Windows but I could access (read/write) windows drives from Linux? Does anyone know good tutorials for this use case? What other things might I have to consider for transition Windows-Linux?

  Read the article

• Dual HDD dual boot Win7/Win7 hibernate corrupts partitions?

  - by Ivan Zlatev

  I have two SSDs in my laptop. Both have 2 partitions each one with Windows 7 64bit and another one with OEM stuff on it (SYSTEM_DRV). I use the BIOS boot menu to boot between the drives. I have removed the drive letters so that no partitions of drive 1 are mapped in windows 2 on drive 2 and wise-versa. What I have observered however is that when I hibernate windows 1, boot windows 2 do some work and shutdown then resume windows 1 - the windows 2 partition will get corrupt quite often. Just happened actually - it is shown as "RAW" in the Disk manager instead of NTFS and windows will blue screen at boot. Alternatively I've seen cases where chkdsk will run and will wipe out all security descriptors making the partition completly unbootable. Why am I seeing these corruptions and what can I do to prevent them?

  Read the article

• What's the fastest way to store/access large files?

  - by philfreo

  I do a lot of video editing on my Mac and need a way to store very large (30 GB) files, and don't have room on my HD. A USB/Firewire external hard drive would work, but it seems way too slow for consistently working with such large files. I've also considered buying another computer, with a large hard drive, and putting it on the same network with a shared folder. What's the fastest / most efficient way to do this? Please consider USB 2.0 speeds, hard drive read times, ethernet speeds, etc. Are there other options I should consider?

  Read the article

• How do I replace a harddrive that is in a two-way mirror storage space on Windows 8?

  - by Jon

  I have a storage space in Windows 8 doing a two-way mirror on three harddrives. The sizes are 297GB, 189GB, and 70GB. I would like to replace the 70GB HD with a larger one. My thought was to remove that drive from the space via the Storage Space control panel, shutdown, replace HD with bigger drive, reboot, add new HD to the storage space. I can't find any options to remove a HD from a storage space in the control panel. Should I just shutdown and swap out the small drive or is there another process for safely replacing the old HD? (By the way, the old HD is still operational.)

  Read the article

• Justifying a memory upgrade, take 2

  - by AngryHacker

  Previously I asked a question on what metrics I should measure (e.g. before and after) to justify a memory upgrade. Perfmon was suggested. I'd like to know which specific perfmon counters I should be measuring. So far I got: PhysicalDisk/Avg. Disk Queue Length (for each drive) PhysicalDisk/Avg. Disk Write Queue Length (for each drive) PhysicalDisk/Avg. Disk Read Queue Length (for each drive) Processor/Processor Time% SQLServer:BufferManager/Buffer cache hit ratio What other ones should I use?

  Read the article

• How is a Chromebook better than using Chrome browser on another OS?

  - by bigpopakap

  I'm looking into getting a Chromebook as a lightweight device to use for basic functions. I'm fully aware of some of the limitations like no native apps, limited functionality while offline (though this is getting better with Google Drive's offline capabilities). Currently, I have a Windows machine on which I've installed Google Drive, so files in that folder are synced. And I use Chrome as my browser. So I have access to all the same apps (Drive, Calendar, Gmail, Google Music, etc.). Is there any advantage to having a Chromebook over my current setup, other than the speed of the lightweight Chrome OS?

  Read the article

• Where can I find ready to use windows scripts that used robocopy?

  - by Geo

  We are installing the Windows Resource Kit, and that installs RoboCopy. We want to have access to a few windows scripts that uses RoboCopy so we can start from those to build something else. Any ideas on where I can find a few samples? NOTE 1: A bit of information. Every time we try to copy D drive to E drive (new drive) we get an error that says: ERROR 32 (0x000000020) Copying File d:\pagefile.sys The process cannot access the file because it is being used by another process. Waiting 30 seconds. Just to help figure it out.

  Read the article

• Recently disinfected laptop still has strange issues

  - by Robsta

  This computer was heavily infected with viruses recently. The hard drive had to be taken out and cleaned by a different machine. The hard drive is now virus free, but Windows still has some strange issues that I need some help fixing. I've re-installed Chrome, but I still have issues with it. It's the same for Firefox and any other browser. When I plug in a USB flash drive, everything is fine, except when it asks me what to do with it I get what you see in the third image. I believe this is Windows 7. Any ideas? Here are the images of some of the issues:

  Read the article

• Clone a Red Hat RAID as part of a disaster recovery plan

  - by Campo

  I am looking for recommendations to clone a Red Hat mirrored raid to a single hard drive located in the same machine. The idea is if the servers hardware ever has an issue we have a similar hardware machine ready to go. All we would have to do is pop in the cloned drive. If the servers RAID ever failed we could just switch to the single drive to maintain uptime and restore the original configuration on the spare server with a backup. This is a restaurant and they are open 7 days a week. We do have time from 12:am to 9:00am to perform the necessary steps for a clone and we talking about under 10 Gigs of information. There is a database on the server. I have looked into Rsync and Clonezilla. But I am just not confident either is capable of completing the task I want. Looking for some suggestions and possibly a step by step if you could be so kind.

  Read the article

• Can Windows 8 boot from FireWire?

  - by Holli

  I read many times Windows 7 is unable to boot from an external FireWire drive but I wonder if Windows 8 is able to do so. I need to run Windows on my Mac but only very few times so my idea was to move it all to an external drive. I have one of the first Intel Macs so running Windows in a virtual machine is not really fun. The performance is just too poor. Adding a Boot Camp partition to my internal drive is also not possible at the moment.

  Read the article

• Creating a file server - How can I use a large VHD file in Hyper-V? (700GB)

  - by barfoon

  Hey everyone, After a few discussions (here, here, and here), I am still unable to create a simple VM that will be used as a fileserver hosted on my Hyper-V box. I have created a fixed 700GB SCSI drive (.vhd file), as I have learned an IDE drive of this size is not possible. Not to sound too cynical, but its blown me away at how much trouble its been to create a large amount of space and start using it. What is the best way to create a fileserver with a drive of this size hosted on Hyper-V Server 2008, and how can I get it going??? Inclusion of OS, driver, integration tools etc, anything you feel is required would be greatly appreciated. Extra information I am using the stand-alone version of Hyper-V server, and not Windows Server 2008. I have tried loading the Linux Integration Tools (linked in the comments of the last link above) onto a SUSE 11 VM and the installation fails, the machine cannot see the vhd at all. Thanks very much,

  Read the article

< Previous Page | 197 198 199 200 201 202 203 204 205 206 207 208  | Next Page >