Search Results

Search found 14989 results on 600 pages for 'street address'.

Page 203/600 | < Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >

• IOS not saving evaluate rule in access-list

  - by DeeJay1

  Hi. I have a basic firewall set up on an pretty od IOS in form of IPv6 access list exterior-in6 evaluate exterior-reflect sequence 1 permit ipv6 any host [my external address] sequence 10 permit tcp any host [my internal address] eq 22 sequence 11 permit icmp any any sequence 800 permit udp any any range 6881 6889 sequence 900 permit tcp any any range 6881 6889 sequence 901 deny ipv6 any any sequence 1000 IPv6 access list exterior-out6 permit ipv6 [my internal subnet] any reflect exterior-reflect sequence 10 Unfortunately the evaluate exterior-reflect sequence 1 line seems to get lost after each reboot, leaving my internal network without access. Any ideas?

  Read the article

• Clarification of the difference between PCI memory addressing and I/O addressing?

  - by KevinM

  Could someone please clarify the difference between memory and I/O addresses on the PCI/PCIe bus? I understand that I/O addresses are 32-bit, limited to the range 0 to 4GB, and do not map onto system memory (RAM), and that memory addresses are either 32-bit or 64-bit. I get the impression that memory addressing must map onto available RAM, is this true? That if a PCI device wishes to transfer data to a memory address, that address must exist in actual system RAM (and is allocated during PCI configuration) and not virtual memory. So if a PCI device only needs to transfer a small amount of data at a time, where there is no advantage to putting it into RAM or using DMA, then I/O addressing is fine (e.g. a parallel port implemented on a PCI card). And why do I keep reading that PCI/PCIe I/O addressing is being deprecated in favour of memory addressing? Thanks!

  Read the article

• Emails going into junk and spf records

  - by user346443

  Hi, our emails are being flagged as junk. I have two different webistes both with their own dedicted ip address. sitea.com = xx.xx.xx.43 siteb.com = xx.xx.xx.44 Im using hmailserver to host our emails and have the smtp bound to the ip address of xx.xx.xx.42 im aware that i can set up a spf record to state that the what servers emails can be sent from v=spf1 mx ip4:xx.xx.xx.43 mx:mail.sitea.com ip4:xx.xx.xx.42 -all Would the fact that email are not sent from the sites ip's be causing them to be flagged as junk. Cheers Cam

  Read the article

• Squid throws error, The requested URL could not be retrieved

  - by Supratik

  Hi Sometimes I am getting the following error The requested URL could not be retrieved While trying to retrieve the URL: http://groups.google.com/ The following error was encountered: Unable to determine IP address from host name for groups.google.com The dnsserver returned: Refused: The name server refuses to perform the specified operation. This means that: The cache was not able to resolve the hostname presented in the URL. Check if the address is correct. Your cache administrator is root. What could be the reason for the above error ? Regards Supratik

  Read the article

• xenserver: xe command never returns?

  - by ethrbunny

  I'm trying to port a xen server 6.2 pool to a new IP address range. I've got three servers total: 2 currently at their new IP but no longer in the pool and one remaining. I'm trying to set IP address information on the two disconnected ones using the xe command and all of its variants. Oddly enough, it never returns with any values. xe host-list It just sits there until I ctrl-c it. The server is still awake and responding though. I can enter other commands (EG ifconfig) and they work fine. If I enter this same command on the remaining server in the pool it works ok. I've tried restarting the toolstack and even rebooting. No change. What am I doing wrong?

  Read the article

• Postfix - How to process incoming emails?

  - by Borivojevic

  Hello Does anybody know how to process incoming emails for virtual mailboxes in postfix? I am building web application where users add new content by sending emails to application. Email address used for each user is custom (eg. [email protected]) and it is dynamically created as a Postfix virtual mailbox. User needs to be able to send email to his custom mailbox address ([email protected]) and i want to process each incoming email, parse it's contents and populate my database with data from email. I tried using Postfix After Queue filter but what i really wont is to process emails once they are saved in users virtual mailbox folder.

  Read the article

• WAMP - phpmyadmin 403 error from localhost, but not from IP 127.0.0.1?

  - by kdub

  I was wondering if anyone can explain this to me. I installed WAMP 2.2. I opened up the dashboard menu, and clicked localhost. I was brought to the WAMP localhost home page. I clicked on phpmyadmin and get a 403 access is denied error message. However, if I type in the ip address 127.0.0.1/phpmyadmin in the address bar, then VOILA, I am in (however, I am not prompted to login to phpmyadmin, I am instantly brought to the phpmyadmin homepage) Please note, I have found the solution to get rid of the 403 error message when entering phpmyadmin from the the localhost extension (change the Deny all setting to Allow all); so I am not asking how to solve that, but my question is: Why if localhost and 127.0.0.1 go to the same spot, will when using the IP addres, I am granted access to subsequent applications and with localhost I am not? Any feedback would be greatly appreciated.

  Read the article

• Ubuntu 11.04 Static IP doesn't take

  - by mrduclaw

  I'm trying to set a static IP address in Ubuntu 11.04. I did a server install. I edited my /etc/network/interfaces file to include: auto eth0 iface eth0 inet static address 10.0.0.100 netmask 255.255.255.0 gateway 10.0.0.1 When I do a /etc/init.d/networking restart this appears to take. After awhile though, that 10.0.0.100 will turn into something dished out by the DHCP server. My problem appears to be similar to this: Ubuntu intrepid - static IP networking keeps restarting with DHCP But I don't have Gnome installed. Is there anything else that's running in the background that could be doing this? And if so, how do I disable it?

  Read the article

• Why configuring manual IP do not work for me in DHCP?

  - by user58859

  I have broadband connection in my laptop. It's getting the IP by protocol. configuration is : ip : 192.168.1.2 subnet : 255.255.255.0 gateway : 192.168.1.1 Now I am curious, In IPV4 properties when instead of choosing "Obtain an IP address automatically", I choose "Use the following IP address" and configure everything same, why it do not work? Do DHCP do not work when we configure the IP manually? (operating system : windows-7) EDIT : After configuring the ip manually, when I used ipconfig/all , it's showing dhcp enabled : NO. I am not doing it. Why it got disabled automatically? and how to enable it? DHCP Enabled. . . . . . . . . . . : No Autoconfiguration Enabled . . . . : Yes IPv4 Address. . . . . . . . . . . : 192.168.1.2(Preferred) Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled

  Read the article

• Setting up a copy of a site with IIS 7?

  - by SJaguar13

  I have a site running on IIS with a dyndns.org domain that points to the IP of the Windows 2008 machine hosting it. I need a copy of that site for development purposes. I set up another folder with all the files, and create a new site in IIS. I don't really have a domain for it, so I was just going to use the IP address. When I go to localhost, 127.0.0.1, or the internal IP, I get bad hostname. If I use the IP address on port 80 (the same as the real version of the site), I get 404 not found. If I use a different port so I don't have them both on the same IP with the same port, I get connection timed out. How do I go about setting this up?

  Read the article

• What OO Design to use ( is there a Design Pattern )?

  - by Blundell

  I have two objects that represent a 'Bar/Club' ( a place where you drink/socialise). In one scenario I need the bar name, address, distance, slogon In another scenario I need the bar name, address, website url, logo So I've got two objects representing the same thing but with different fields. I like to use immutable objects, so all the fields are set from the constructor. One option is to have two constructors and null the other fields i.e: class Bar { private final String name; private final Distance distance; private final Url url; public Bar(String name, Distance distance){ this.name = name; this.distance = distance; this.url = null; } public Bar(String name, Url url){ this.name = name; this.distance = null; this.url = url; } // getters } I don't like this as you would have to null check when you use the getters In my real example the first scenario has 3 fields and the second scenario has about 10, so it would be a real pain having two constructors, the amount of fields I would have to declare null and then when the object are in use you wouldn't know which Bar you where using and so what fields would be null and what wouldn't. What other options do I have? Two classes called BarPreview and Bar? Some type of inheritance / interface? Something else that is awesome?

  Read the article

• Create and redirect subdomain for a parked domain?

  - by Steve

  I have a domain parked.com which is parked onto real.com. I have created the subdomain m.parked.com by editing parked.com's named file: m 14400 IN A ip-address www.m 14400 IN A ip-address This works somewhat: if I go to m.parked.com it redirects to http://m.parked.com/cgi-sys/defaultwebpage.cgi This is my question: I would like to redirect this subdomain to real.com as that is the domain it is parked on. I do not know how to do this as parked.com does not have its own .htaccess file, etc. (due to it being a parked domain) so I can't do any mod_rewrite magic. Can anyone help me? Thanks EDIT: Clarification

  Read the article

• How to add network printer remotely without knowing the IP?

  - by Steve

  Assume your friend from over 100km away asked you to add a network printer to his computer since you're so tech savvy. How would you add network printer remotely in this case? You would need: 0. Remote connection to your friend's computer 1. Printer IP and brand/model names 2. Respective drivers downloaded either from manufacturer's website or Windows Update driver Question is, how would you find out the IP address of the printer without bothering your friend too much with technical steps? Since your friend isn't as tech savvy as you - they wouldn't know which buttons to press to get IP address.

  Read the article

• Two routers in a LAN

  - by taxi

  router A no wifi +--- pc01 +--- pc02 | +--- router B wifi +--- pc03 +--- printer In my LAN I have a modem-router (say A) (no wifi connection) acting as DHCP server, and connected to the Internet. Now, I want to add another router (say B) (with wifi connection) to the LAN, in order to connect wifi pc's and net printers. Here I would disable DCHP server functionality. Is it correct to connect router B to router A via an ethernet port? In router A I define an IP address (eg 192.168.1.100) to be assigned to router B (MAC address). I expect to see router B listed as an attached device, in router A's status, but on the contrary it is not listed.

  Read the article

• Why can't we reach some (but not all) external web service via VPN connection?

  - by Paul Haldane

  At work (UK university) we use a set of Windows servers running WS2008R2 and RRAS which offer VPN service to students in our accommodation. We do this to associate the network connections with individuals. Before they've connected to the VPN all they can talk to is the stuff thats needed to setup the VPN and a local web site with documentation on how to connect. Medium term we'll probably replace this but it's what we're using at the moment. VPN on the 2008 servers allocates client a private (10.x) address. Access to external sites is through NAT on the campus routers (same as any other directly connected client on a private address). Non-VPN connections aren't seeing this problem. Older servers run WS 2003 and ISA2004. That setup works but has become unreliable under load. Big difference there was that we were allocating non-RFC1918 addresses to the clients (so no NAT required). Behaviour we're seeing is that once connected to the VPN, clients can reach local web sites (that is sites on the campus network) but only some external sites. It seems (but this may be chance) that the sites we can reach are Google ones (including YouTube). We certainly have trouble reaching Microsoft's Office 365 service (which is a pain because that's where mail for most of our students is). One odd bit of behaviour is that clients can fetch (using wget on a Windows 7 client) http://www.oracle.com/ (which gets a 301 redirect) but hangs when asked to fetch http://www.oracle.com/index.html (which is what the first URL redirects to). Access works reliably if we configure clients to use our local web proxies (Squid). My gut tells me that this is likely to be something in the chain dropping replies either based on HTTP inspection or the IP address in the reply. However I'm puzzled about why we're seeing this with the VPN clients. Plan for tomorrow (when I'm back in the office) is to setup a web server on external connection so that we can monitor behaviour at both ends of the conversation (hoping that the problem manifests itself with our test server). Any suggestions for things we should be looking at?

  Read the article

• curl blocked at TMG firewall

  - by jemtube100

  i using TMG (threat management gateway) firewall at my web server. when i try to use Curl from outside, this firewall was blocked the connection. what rule/setting that i need to create at TMG to allow it. the error state as below : Refresh page: Search for the page again by clicking the Refresh button. The timeout may have occurred due to Internet congestion. Check spelling: Check that you typed the Web page address correctly. The address may have been mistyped. Access from a link: If there is a link to the page you are looking for, try accessing the page from that link. </UL> <HR color=#c0c0c0 noShade> <P id=L_defaultr_11>Technical Information (for support personnel)</P> <UL> <LI id=L_defaultr_12>Error Code: 403 Forbidden. The server denied the specified Uniform Resource Locator (URL). Contact the server administrator. (12202)

  Read the article

• You cannot do cross joins in SQL Azure but there is a way around that....

  - by SeanBarlow

  So I was asked today how to do cross joins in SQL Azure using Linq. Well the simple answer is you cant do it. It is not supported but there are ways around that. The solution is actually very simple and easy to implement. So here is what I did and how I did it. I created two SQL Azure Databases. The first Database is called AccountDb and has a single table named Account, which has an ID, CompanyId and Name in it. The second database I called CompanyDb and it contains two tables. The first table I named Company and the second I named Address. The Company Table has an Id and Name column. The Address Table has an Id and CompanyId columns. Since we cannot do cross joins in Azure we have to have one of the models preloaded with data. I simply put the Accounts into a List of accounts and use that in my join.   var accounts = new AccountsModelContainer().Accounts.ToList(); var companies = new CompanyModelContainer().Companies; var query = from account in accounts             join company in                 (                       from c in companies                      select c                  ) on account.CompanyId equals company.Id             select new AccountView() {                                               AccountName = account.Name, CompanyName = company.Name,                                 Addresses = company.Addresses                         }; return query.ToList();   So as long as you have your data loaded from one of the contexts you can still execute your queries and get the data back that you want.

  Read the article

• Does anyone know of a inexpensive NAT router that has the ability to limit access to the Internet to

  - by Corey

  Does anyone know of a inexpensive NAT router that has the ability to limit access to the Internet to a specific MAC address? I know the Linksys routers have a MAC filtering feature, but it is the opposite of what I need. It allows you to block access to a specific MAC address. I need something that will block all, but allow an exception. I'm dealing with some VOIP issues in my company's network, and I think the answer is to have a separate router on the network for my PBX to use. I want to make sure that other nodes are not allowed to access the Internet via this second router.

  Read the article

• How can one find software development work that involves directly the final end user?

  - by RJa

  I've worked in software development for 15 years and, while there have been signficant personal achievements and a lot of experience, I've always felt detached from the man/woman-on-the-street, the every day person, how it affects their lives, in a number of ways: the technologies: embedded software, hidden away, stuff not seen by the everyday person. Or process technology supporting manufactured products the size of the systems, meaning many jobs, divided up, work is abstract, not one person can see the whole picture the organisations: large, with departments dealing with different areas, the software, the hardware, the marketing, the sales, the customer support the locations and hours: out-of-town business parks away from the rest of society, fixed locations, inflexible: 9-5 everyday This to me seems typical of the companies I worked for and see elsewhere. Granted, there are positives such as the technology itself and usually being among high calibre co-workers, but the above points frustrate me about the industry because they detach the work from its meaning. How can one: change these things in an existing job, or compensate for them? find other work that avoids these and connects with the final end user? Job designs tend to focus on the job content and technical requirements rather than how the job aims to fulfil end user needs, is meaningful.

  Read the article

• It Ain't Over 'Til It's Over

  - by Oracle OpenWorld Blog Team

  Oracle OpenWorld 2012 is behind us. Well, for San Francisco, anyhow. The team is already working on the Latin America event which takes place in December in Sao Paulo, and an OpenWorld in Asia for 2013 as well. And of course they're already working on the next San Francisco OpenWorld for 2013. So what happens after the conference is over? People pack up demo and network gear and ship it out to wherever it's going next; take down and recycle signage; strike the keynote set, the exhibition and demo halls, the street tents, and anything else that was constructed just for the conference. There's a lot of post-conference analyis going on too. Oracle and partner marketing teams are looking at and following up on the leads they got from booth, demo, and lounge traffic. The events team is evaluating the session and conference surveys you filled out if you attended -- looking to identify the best speakers, what worked and didn't work, how you liked the venues, the food, the entertainment, the presentations. From all of that information will come recommendations for next year on what to keep doing, what to do better, and what not to do at all. The goal for each year's conference is to be better than last year's. If you attended and haven't filled out the surveys yet, you have until October 19 for them to be counted, and for you to be entered into a daily sweepstakes. Click here for more information. Posts to this blog will slow down for a while, but we'll post news about Oracle OpenWorld in San Francisco and around the world when we have it. Any suggestions about future blog topics are welcome. Oh - I forgot to mention that you can sign up to be notified when registration for Oracle OpenWorld 2013 goes live. If you register at that time you'll get the best discount available on attending next year. So sign up, and stay tuned.

  Read the article

• Page loading hangs and never times out (Apache)

  - by Lucas -luky- N.

  I have set up Apache2 on a guest Ubuntu 10.04 OS (virtualbox). I have created a "big" HTML file (4MB) with only plain text and when I access a page through my local IP address such as http://192.168.0.100 it successfully loads the entire page. However, when I try to access it through my public IP address the browser loads part of the page and then hangs forever on "loading". I can load a simple webpage though. I'm not sure whether it's an issue with my Apache configuration, Virtualbox, Router or Modem. Any clues? Tried enabling Debug and mod_status but didn't find any useful information.

  Read the article

• Can't connect to service on ubuntu?

  - by user36914

  I have a service i just installed on a ubuntu workstation machine. Say its running under port 511. I can connect locally : telnet localhost 511 When i try to connect from a remote machine it fails telnet 192.168.0.1 511 Whats wierd is i tried to connect locally using the ip address and i get the following error: "Unable to connect to remote host: Connection Refused" I checked the status of the firewall: sudo ufw status and get back "status:inactive" So does anyone know why i can't connect remotely since the firewall is disabled and why can't i connect locally using its ip address. I don't know if this matters but its running under esxi.

  Read the article

• cannot using internet in VMWare

  - by user66247

  I am using VMware Workstation version 7 on Ubuntu 10.10. I installed Windows XP service pack 3 for guest os. Within VMWare, I am using bridge connection that I assigned static IP address to be able to ping host IP address but I cannot ping default router gateway. I also tried to command "/etc/init.d/vmware start" on terminal. All tasks are able to start successfully except "VM communication interface socket family" I am not sure that how to setup network for my VMWare by using wireless. Thanks in advance.

  Read the article

• What can I do in order to inform users of potential errors in my software in order to minimize liability?

  - by phobitor

  I'm an independent software developer that's spent the last few months creating software for viewing and searching map data. The software has some navigation functionality as well (mapping, directions,etc). The eventual goal is to sell it in mobile app markets. I use OpenStreetMap as my data source. I'm concerned about liability for erroneous map data / routing instructions, etc that might result when someone uses the application. There are a lot of stories on the internet where someone gets into an accident or gets stuck or gets lost because of their GPS unit/Google Maps/mapping app... I myself have come across incorrect map data as well in a GPS unit I have in my car. While I try to make my own software as bug free as possible, no software is truly bug free. And moving beyond what I can control, OpenStreetMap data (and street map data in general) is prone to errors as well. What steps can I take to clearly inform the user that results from the software aren't always perfect, and to minimize my liability?

  Read the article

• Postgres Remote Access

  - by boot-baby-boot

  I am trying to connect to postgres remotely.I have followed this tutorial http://www.cyberciti.biz/faq/howto-fedora-linux-install-postgresql-server/ and have executed the following commands to see if the remote access is possible. [root@printmyworld ~]# egrep -i "(listen_addresses|port|tcpip_socket).*=.+" /var /lib/pgsql/data/postgresql.conf #listen_addresses = '*' # what IP address(es) to listen on; #port = 5432 [root@printmyworld ~]# lsof +c0 -anPiTCP -upostgres COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME postmaster 9323 postgres 3u IPv4 2875987353 TCP 127.0.0.1:5432 (LISTEN ) postmaster 9323 postgres 4u IPv6 2875987354 TCP [::1]:5432 (LISTEN) I am suspicious of this line: postmaster 9323 postgres 3u IPv4 2875987353 TCP 127.0.0.1:5432 (LISTEN My server ip address is 1yy.000.1xx.000 .Should it be 1yy.000.1xx.000:5432

  Read the article

< Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >