Search Results

Search found 7679 results on 308 pages for 'report designer'.

Page 207/308 | < Previous Page | 203 204 205 206 207 208 209 210 211 212 213 214  | Next Page >

• Problems dualbooting Ubuntu because of UEFI

  - by Koffeehaus

  I have an X-series Asus laptop which I just bough about a month ago. I want to dualboot Ubuntu - Windows. I can easily access LiveUSB with both UEFI enabled and disabled. I heard that there were problems with UEFI, so I disabled it. After I've installed the system I couldn't access it. It just boots to Windows straight. Another unusual thing, that never happened to me before was that the partition editor wanted me to create a BIOS reserved area, which I did, but not at the beginning of the table. Any ideas how to access the Ubuntu partition? As far as I can guess both Windows and Ubuntu have to be both of the same type of boot, either Legacy or EFI. This is not the case of what I have now. So, if I reinstall Ubuntu in UEFI mode that correlates with my Windows type, will I then be able to boot into it? I have a constraint, my laptop doesn't have a CD ROM, so I cannot reinstall WIndows, nor can I move around the Windows recovery partition. This is the boot-repair report : http://paste.ubuntu.com/1354254/

  Read the article

• Software Center - Items cannot be installed or removed until package catalog is repaired"

  - by Stephanie

  I tried to install back in time and now I keep getting the message 'items cannot be installed or removed until package catalog is repaired. I have tried sudo apt-get install -f then get Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: backintime-gnome The following packages will be upgraded: backintime-gnome 1 upgraded, 0 newly installed, 0 to remove and 2 not upgraded. 1 not fully installed or removed. Need to get 0 B/39.4 kB of archives. After this operation, 24.6 kB of additional disk space will be used. Do you want to continue [Y/n]? when I click Y, I get the following message dpkg: dependency problems prevent configuration of backintime-gnome: backintime-gnome depends on backintime-common (= 1.0.7); however: Version of backintime-common on system is 1.0.8-1. dpkg: error processing backintime-gnome (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: backintime-gnome E: Sub-process /usr/bin/dpkg returned an error code (1) stephanie@stephanie-ThinkPad-T61:~$ sudo dpkg --configure -a dpkg: dependency problems prevent configuration of backintime-gnome: backintime-gnome depends on backintime-common (= 1.0.7); however: Version of backintime-common on system is 1.0.8-1. dpkg: error processing backintime-gnome (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: backintime-gnome

  Read the article

• No space left on disk

  - by Ned

  folks. I'm trying to copy/move files to an external 1 TB hard drive with about 50 GB remaining space. I receive a "no space left on disk" when I try. I've moved files off and retried, but still get the same message. Disk Usage Analyzer, Properties, and freeware Treesize all report available hard drive space of about 50 GB. I've tried df -i (50 GB available) and df -k, with the latter reporting only 1% of inode usage. I've been able to save files from Firefox to the drive also. I can't even rename files without getting the message. Yesterday in the midst of trying to figure this out I tried to move 4 files to the drive and got the message. Today, I found them on the drive. What's up with that? (That's the only time that has happened to my knowledge.) Is this an ubuntu problem? or is my hard drive just about to fail because of something like a controller problem? Any thoughts would be appreciated.

  Read the article

• Lenovo Y460 Intel Driver Secondary Display Flickering

  - by ultimatebuster

  This is a part of the massive dump of problems I'm encountering with my Lenovo Y460 and Ubuntu. Problem: ATI PowerXpress doesn't really work. Doesn't work as I have to use the open source driver with hacks. Turned off ATI card at boot Details on how I accomplished that: http://ubuntuforums.org/showthread.php?p=10955831#post10955831 Installing the ATI drivers results in a failure of the intel drivers to work with Ubuntu Class (all animations have to turned off). Anyway to fix this problem to allow switchable graphics to work? The problem above has been fixed by FGLRX (Catalyst 11.6) is it compatible with kernel 2.6.39? However, there's another issue. If I connect my secondary monitor (VGA 17'') while using the Intel driver, I would not be able to use that screen as there's flickering and tearing, making the screen blurry and usable. Here's the fglrxinfo: $ fglrxinfo display: :0.0 screen: 0 OpenGL vendor string: Tungsten Graphics, Inc OpenGL renderer string: Mesa DRI Intel(R) Ironlake Mobile GEM 20100330 DEVELOPMENT OpenGL version string: 1.4 (2.1 Mesa 7.10.2) Any fixes for that? Potential related bug report on launchpad: https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/750259 However I can't confirm because the video showing that is much more dramatic than what I have, mine are tiny flickering that won't be captured by video cameras as I've tried, but enough to make it blurry for humans.

  Read the article

• I'm doing 90% maintenance and 10% development, is this normal?

  - by TiredProgrammer

  I have just recently started my career as a web developer for a medium sized company. As soon as I started I got the task of expanding an existing application (badly coded, developed by multiple programmers over the years, handles the same tasks in different ways, zero structure) So after I had successfully extended this application with the requested functionality, they gave me the task to fully maintain the application. This was of course not a problem, or so I thought. But then I got to hear I wasn't allowed to improve the existing code and to only focus on bug fixes when a bug gets reported. From then on I have had 3 more projects just like the above, that I now also have to maintain. And I got 4 projects where I was allowed to create the application from scratch, and I have to maintain those as well. At this moment I'm slightly beginning to get crazy from the daily mails of users (read managers) for each application I have to maintain. They expect me to handle these mails directly while also working on 2 other new projects (and there are already 5 more projects lined up after those). The sad thing is I have yet to receive a bug report on anything that I have coded myself, for that I have only received the occasional lets do things 180 degrees different change requests. Anyway, is this normal? In my opinion I'm doing the work equivalent of a whole team of developers. Was I an idiot when I initially expected things to be different? I guess this post has turned into a big rant, but please tell me that this is not the same for every developer. P.S. My salary is almost equal if not lower then that of a cashier at a supermarket.

  Read the article

• Are there legitimate reasons for returning exception objects instead of throwing them?

  - by stakx

  This question is intended to apply to any OO programming language that supports exception handling; I am using C# for illustrative purposes only. Exceptions are usually intended to be raised when an problem arises that the code cannot immediately handle, and then to be caught in a catch clause in a different location (usually an outer stack frame). Q: Are there any legitimate situations where exceptions are not thrown and caught, but simply returned from a method and then passed around as error objects? This question came up for me because .NET 4's System.IObserver<T>.OnError method suggests just that: exceptions being passed around as error objects. Let's look at another scenario, validation. Let's say I am following conventional wisdom, and that I am therefore distinguishing between an error object type IValidationError and a separate exception type ValidationException that is used to report unexpected errors: partial interface IValidationError { } abstract partial class ValidationException : System.Exception { public abstract IValidationError[] ValidationErrors { get; } } (The System.Component.DataAnnotations namespace does something quite similar.) These types could be employed as follows: partial interface IFoo { } // an immutable type partial interface IFooBuilder // mutable counterpart to prepare instances of above type { bool IsValid(out IValidationError[] validationErrors); // true if no validation error occurs IFoo Build(); // throws ValidationException if !IsValid(…) } Now I am wondering, could I not simplify the above to this: partial class ValidationError : System.Exception { } // = IValidationError + ValidationException partial interface IFoo { } // (unchanged) partial interface IFooBuilder { bool IsValid(out ValidationError[] validationErrors); IFoo Build(); // may throw ValidationError or sth. like AggregateException<ValidationError> } Q: What are the advantages and disadvantages of these two differing approaches?

  Read the article

• Displaying Datamatrix in application error screen

  - by DaveNay

  Quite often we will get a report from a user in the field saying there was an error in our application. Frequently this leads to the typical round of "What was the error?" "I don't know, it was just an error." We of course log these faults to the log files, and we can even enable detailed debug logs, but this involves the end user changing a setting in the configuration file and then finding the correct files and then emailing them to us. As I'm sure you can all imagine, there are plenty of pitfalls and alligators in this methodology. Recently a couple of people have used their cell phone to email me a "screen capture" of the fault, and while this helps, we still have to scrutinize the image to find the exact fault, and if enabled, the stack trace. So this evening, I had the brilliant idea (IMHO) to encode the fault into a Datamatrix barcode image and then encourage users to send me a picture from their cell phone. I can then decode the datamatrix and get a parse-able error message! Our core technology is machine vision, so the decoding of the datamatrix image would be trivial, I just need to find a method of generating the actual image to display in the fault handler. Thoughts?

  Read the article

• Announcing Two Papers Addressing the RPAS Fusion Client

  - by Oracle Retail Documentation Team

  Oracle Retail has published two documents to My Oracle Support addressing the Retail Predictive Application Server (RPAS) Fusion Client, a web-based rich client developed using the latest Oracle Application Development Framework (ADF). The Fusion Client provides an enhanced user experience for communicating with the RPAS server. Oracle Retail Predictive Application Server Fusion Client Getting Started Guide Doc ID 1492759.1The Retail Predictive Application Server (RPAS) is a configurable platform that provides capabilities such as a multidimensional database structure, batch and online processing, a configurable user interface, a configurable calculation engine, user security, and utility functions such as importing and exporting, all on a highly scalable technical environment that can be deployed on a variety of hardware. This paper addresses typical questions that arise during setting up and deploying the Fusion Client, provides performance recommendations, and highlights the differences between the Classic Client and the Fusion Client. Oracle Retail RPAS Fusion Client Performance Issue Report Doc ID 1493747.1Performance issues can be frustrating for customers, and Oracle Retail will strive to assist you as you attempt to enhance the performance of your systems. To ensure the timeliest processing of your issue, retailers and partners are encouraged to respond as thoroughly as possible to each question in this document, which can be sent back for analysis by logging a Service Request and following typical Customer Support processes. The sections of the document solicit information about the following: Performance Issue Description Performance Issue Details System Configuration Data Application Configuration Data Performance Log Files

  Read the article

• What is the recommended MongoDB schema for this quiz-engine scenario?

  - by hughesdan

  I'm working on a quiz engine for learning a foreign language. The engine shows users four images simultaneously and then plays an audio file. The user has to match the audio to the correct image. Below is my MongoDB document structure. Each document consists of an image file reference and an array of references to audio files that match that image. To generate a quiz instance I select four documents at random, show the images and then play one audio file from the four documents at random. The next step in my application development is to decide on the best document schema for storing user guesses. There are several requirements to consider: I need to be able to report statistics at a user level. For example, total correct answers, total guesses, mean accuracy, etc) I need to be able to query images based on the user's learning progress. For example, select 4 documents where guess count is 10 and accuracy is <=0.50. The schema needs to be optimized for fast quiz generation. The schema must not cause future scaling issues vis a vis document size. Assume 1mm users who make an average of 1000 guesses. Given all of this as background information, what would be the recommended schema? For example, would you store each guess in the Image document or perhaps in a User document (not shown) or a new document collection created for logging guesses? Would you recommend logging the raw guess data or would you pre-compute statistics by incrementing counters within the relevant document? Schema for Image Collection: _id "505bcc7a45c978be24000005" date 2012-09-21 02:10:02 UTC imageFileName "BD3E134A-C7B3-4405-9004-ED573DF477FE-29879-0000395CF1091601" random 0.26997075392864645 user "2A8761E4-C13A-470E-A759-91432D61B6AF-25982-0000352D853511AF" audioFiles [ 0 { audioFileName "C3669719-9F0A-4EB5-A791-2C00486665ED-30305-000039A3FDA7DCD2" user "2A8761E4-C13A-470E-A759-91432D61B6AF-25982-0000352D853511AF" audioLanguage "English" date 2012-09-22 01:15:04 UTC } 1 { audioFileName "C3669719-9F0A-4EB5-A791-2C00486665ED-30305-000039A3FDA7DCD2" user "2A8761E4-C13A-470E-A759-91432D61B6AF-25982-0000352D853511AF" audioLanguage "Spanish" date 2012-09-22 01:17:04 UTC } ]

  Read the article

• Ubuntu on Samsung NP700Z5B - no Grub

  - by copolii

  I just bought a Samsung NP700Z5B laptop. Gorgeous machine and great performance! I do 2 things when I get a new laptop: Format the HD and install Winblows from a CD to ditch the bloatware Install some variant of Linux on it (lately Ubuntu) Step 1 worked fine (until earlier today), but I haven't been able to install Ubuntu on it for the past 3 days! I've tried Mint12, Ubuntu 12.04, Ubuntu 11.10, Ubuntu 11.04 and Ubuntu 10.04. The live CD and the installations all run fine and report no problems, but when I reboot grub is nowhere to be found! The system goes directly to Winblows! I've tried booting from the liveCD and re-installing grub via the chroot and purge & reinstall methods (https://help.ubuntu.com/community/Grub2) and neither makes a difference. I've also tried copying the boot sector: dd if=/dev/sda of=linux.bin bs=512 count=1 and putting it on c: then setting bcdedit to add the entry to the Windows bootloader with no results. Earlier today I decided to try and set my boot partition as an EFI boot partition ... bad choice, now I don't even have the Winblows boot loader. I've officially ran out of ideas. Tried calling Samsung, but they're closed (they'd probably say something stupid along the lines of "Samsung recommends Windows 7" ... I've had Dell say that to me). Any help would be greatly appreciated. Update 1 Tried re-installing 12.04 and now I get the screen continously turning off and back on, but still no sign of booting ... it has been doing it for 15 mins so far (I set the boot partition type to ext2 instead of ext4) Update 2 Well ... this just gets better and better. I inserted the installation USB key to reboot it and the flickering stopped for about a minute (remained on) then it started turning off and on again

  Read the article

• Ubuntu 14.04: Fine tuning Touchpad for ThinkPad S431

  - by ramgorur

  I am using Ubuntu 14.04 on Lenovo ThinkPad S431. The touchpad is very bumpy, tricky to use. Slides down with a small touch, sometimes jerks erratically. I have tried to modify the settings in /usr/share/X11/xorg.conf.d/50-synaptics.conf file as below -- Section "InputClass" Identifier "touchpad catchall" Driver "synaptics" MatchIsTouchpad "on" MatchDevicePath "/dev/input/event*" Option "JumpyCursorThreshold" "250" Option "VertResolution" "100" # Option "HorizResolution" "65" # Option "MinSpeed" "1" # Option "MaxSpeed" "1" # Option "AccelerationProfile" "1" # Option "AdaptiveDeceleration" "8" # Option "ConstantDeceleration" "1" # Option "VelocityScale" "128" Option "HorizHysteresis" "150" Option "VertHysteresis" "150" EndSection There are lots of options here, does anyone know how to get a fine-tuned values for the above options (for ThinkPad S431)? The Hysteresis values seems to alleviate the problem a little bit, but failed to get a perfect result. EDIT: According to this bug report for ThinkPad X230 (+X230t), I set these values and quite good for now -- Option "VertResolution" "100" Option "HorizResolution" "65" Option "MinSpeed" "1" Option "MaxSpeed" "1" Option "AccelerationProfile" "2" Option "AdaptiveDeceleration" "16" Option "ConstantDeceleration" "16" Option "VelocityScale" "32" Option "HorizHysteresis" "50" Option "VertHysteresis" "50" and then you need to increase the cursor speed manually from the Unity mouse settings. But I am still looking for a fully functional (possibly with all the gestures) and a fine-tuned touchpad settings for S431. Further help is appreciated.

  Read the article

• How to debug a fatal system crash - [graphical loop DOTA2]?

  - by Huw

  Whilst playing DOTA2, I occasionally and apparently randomly seem to be experiencing a fatal crash where the display freezes fixed and the audio loops over approx the last .5 of a second. Now, I'm interested in resolving this - but my trouble is I don't know where to start. The error appears non-reproducible (I've tried returning to games and deploying the same combination of events in hopes of pinning to to a certain shader etc), and I don't know which part of 'the stack' it might be coming from. Variables that occur to me: I custom build this system, did I do something wrong - is my PSU not providing enough power to the graphics card? I am running Steam and DOTA under Linux, could this new software have a bug Might it be something to do with my ATI Catalyst graphics drivers Is some other background process interfering I'm usually mid game when this occurs, so i quickly kill the power and reboot (when i'm lucky i can get back in with only 1-2 mins lost!). So my question here relates to logs. Where should I start to look or how might I set up logs to help me pin down a fatal crash of this kind by recording moments up to / before a crash and is this likely to be something I should push Steam to do, or is there something at a system level? Then perhaps I can return with a more specific question and perhaps even a bug report :) Many thanks in advance.

  Read the article

• Can't update packages or use Ubuntu Software Center (E: Some index files failed to download. They have been ignored, or old ones used instead.)

  - by user94189

  I get the following errors when trying to run the auto Update Manager Could not initialize the package information An unresolvable problem occurred while initializing the package information. Please report this bug against the 'update-manager' package and include the following error message: 'E:Encountered a section with no Package: header, E:Problem with MergeList /var/lib/apt/lists/ppa.launchpad.net_bugs-sehe_zfs-fuse_ubuntu_dists_precise_main_binary-amd64_Packages, E:The package lists or status file could not be parsed or opened.' When I run sudo apt-get update, I get these errors W: GPG error: http://us.archive.ubuntu.com precise Release: The following signatures were invalid: BADSIG 40976EAF437D05B5 Ubuntu Archive Automatic Signing Key <[email protected]> W: GPG error: http://ppa.launchpad.net precise Release: The following signatures were invalid: BADSIG 1FFD34C9EB13C954 Launchpad CoverGloobus W: GPG error: http://ppa.launchpad.net precise Release: The following signatures were invalid: BADSIG 4A67F94CBF965FF5 Launchpad PPA for Happy-Neko W: Failed to fetch http://ppa.launchpad.net/bugs-sehe/zfs-fuse/ubuntu/dists/precise/main/source/Sources 404 Not Found W: Failed to fetch http://ppa.launchpad.net/bugs-sehe/zfs-fuse/ubuntu/dists/precise/main/binary-amd64/Packages 404 Not Found W: Failed to fetch http://ppa.launchpad.net/bugs-sehe/zfs-fuse/ubuntu/dists/precise/main/binary-i386/Packages 404 Not Found E: Some index files failed to download. They have been ignored, or old ones used instead.

  Read the article

• How to fix Black screen?

  - by stupidwhiteguy

  so I recently had my question deleted and merged into a standard how to for blank screens. I am relatively new to This type of computer work and i don't understand the steps nessary to diagnose my problem well enough to solve it so this help full how to has me feeling helpless I can use Ctrl + Alt +F1 and log in So how do I use sudo commands to fix the blank screen on my old dell? sudo lsoci -nn tells me my video card is a ATI rage 128 pro ultra tf /var/log/Xorg.0.log tells me Permission denied that is all i get Sudo apt-get install --reinstall unity tried thay also have also tried Apt-get update and upgrade Please dont close this question without providing an actual answer or if you think it is an exact duplicate provide a solution that worked for that question. I see a lot of these questions as closed and there is no real answer given I will try any solutions available and report results so that others can also solve problems not be overwhelmed by overly broad troubleshooting guides that do nothing to help solve specific issues The nomodeset change from quiet splash also yields no results on reboot I still get a blank screen this screen still has contorl alt f1 abilities but that is it contorl alt f8 causes blinking cursor and F7 gets a crazy flash with green and blue then blank screen Contorl alt f1 a log in prompt in text only when run in recovery mode with failsafe graphics its says the syestem is running in low graphics mode your screen graphics card and input device settings could not be detected correctly. You will need to configure these your self how do i do that? I got this /var/log/failsafeX-backup-120909200641.tar as the location of my log files but i have no idea how to axcess sounds work in blank screen also screen responds or flashes after log in is typed and password entered really any help is good I don't even know where to start I believe 12.04 is installed and functioning but i don't think I can see it at the end of the error log it says error setting mtrr (base= oxf0000000, size= 0x01000000, type=1) inappropriate ioctl for device(25) i have tried to provide as much info as I understand how to provide

  Read the article

• Is it possible to get xRandR to see two separate outputs with the nvidia driver?

  - by rumtscho

  I have two monitors, which I have set up with nvidia-settings in Twinview. The result: When I want to do something in xRandR, it does not function. It doesn't report one output per video card head, but a single output mapped to the combined area of both monitors: rumtscho@bradbury:~$ xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 3840 x 1440, current 3840 x 1440, maximum 3840 x 1440 default connected 3840x1440+0+0 0mm x 0mm 3840x1440 50.0* Now I promised somebody to help test a driver. The developer is using an open source driver for Intel video cards, and his driver assumes that there is more than one xRandR output, each mapped to a monitor. So I tried rewriting my xorg.conf to somehow get two outputs to show up, but failed. Googling showed that people faced with the xRandR-nvidia problem either stopped using xRandR and achieved what they needed with nvidia-settings, or changed their driver to nouveau. The first is not going to help in my situation, and I am not willing to give up the proprietary driver, because Compiz won't work without it. So does anybody know a way to get nvidia to actually pass on information on outputs to xRandR?

  Read the article

• Why am I getting this error while installing gnome?

  - by Sreehari Rajendran

  i have raring ringtail. I installed gnome a couple days ago. I try to install extensions but the site says I don't have the latest version. I type the command sudo apt-get install gnome-shell and I get this error Reading package lists... Done Building dependency tree Reading state information... Done gnome-shell is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 138 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up initramfs-tools (0.103ubuntu0.7) ... update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-25-generic cp: cannot stat ‘/module-files.d/libpango1.0-0.modules’: No such file or directory cp: cannot stat ‘/modules/pango-basic-fc.so’: No such file or directory E: /usr/share/initramfs-tools/hooks/plymouth failed with return 1. update-initramfs: failed for /boot/initrd.img-3.8.0-25-generic with 1. dpkg: error processing initramfs-tools (--configure): subprocess installed post-installation script returned error exit status 1 No apport report written because MaxReports is reached already Errors were encountered while processing: initramfs-tools E: Sub-process /usr/bin/dpkg returned an error code (1) why?

  Read the article

• CodePlex Daily Summary for Monday, November 11, 2013

  CodePlex Daily Summary for Monday, November 11, 2013Popular ReleasesULS Log Viewer Feature: ULS Log Viewer Feature: What's getting installed? - The solution include Custom Action (New action in Site Menu). Features: - Only Site Administrators can see Custom Action in site menu. - Multi-Language SUPPORT! (English, Hebrew). - Works against Secure Store Service to use administrator rights for getting access to ULS Logs Path on farm servers (Use the guide for creating new SSA). - Load only the last log file from ULS log path. - Gets automatically the ULS log path from Central Administration. - Choose from whi...Lib.Web.Mvc & Yet another developer blog: Lib.Web.Mvc 6.3.3: Lib.Web.Mvc is a library which contains some helper classes for ASP.NET MVC such as strongly typed jqGrid helper, XSL transformation HtmlHelper/ActionResult, FileResult with range request support, custom attributes and more. Release contains: Lib.Web.Mvc.dll with xml documentation file Standalone documentation in chm file and change log Library source code Sample application for strongly typed jqGrid helper is available here. Sample application for XSL transformation HtmlHelper/ActionRe...Magick.NET: Magick.NET 6.8.7.501: Magick.NET linked with ImageMagick 6.8.7.5. Breaking changes: - Refactored MagickImageStatistics to prepare for upcoming changes in ImageMagick 7. - Renamed MagickImage.SetOption to SetDefine.Media Companion: Media Companion MC3.587b: Fixed* TV - Locked shows display correctly after refresh * TV - missing episodes display in correct colour for missed or to be aired * TV - Rescrape of Multi-episodes working. * TV - Cache fix where was writing episodes multiple times * TV - Fixed Cache writing missing episodes when Display missing eps was disabled. Revision HistoryGenerate report of user mailbox size for Exchange 2010: Script Download: Script Download http://gallery.technet.microsoft.com/scriptcenter/Generate-report-of-user-e4e9afcaCheck SQL Server a specified database index fragmentation percentage (SQL): Script Download: Script Download http://gallery.technet.microsoft.com/scriptcenter/Check-SQL-Server-a-a5758043Save attachments from multiple selected items in Outlook (VBA): Script Download: Script Download: http://gallery.technet.microsoft.com/scriptcenter/Save-attachments-from-5b6bf54bRemove Windows Store apps in Windows 8: Script Download: Script Download http://gallery.technet.microsoft.com/scriptcenter/Remove-Windows-Store-Apps-a00ef4a4PCSX-Reloaded: 1.9.94: General changes:Support for compressed audio in cue files. ECM support. OS X changes:32-bit support has been dropped Partial French and Hungarian translationsDynamics AX 2012 R2 Kitting: AX 2012 R2 CU7 release of Kitting: Here is the AX 2012 R2 CU7 release of kitting. Released both as a XPO and a model.VidCoder: 1.5.12 Beta: Added an option to preserve Created and Last Modified times when converting files. In Options -> Advanced. Added an option to mark an automatically selected subtitle track as "Default". Updated HandBrake core to SVN 5878. Fixed auto passthrough not applying just after switching to it. Fixed bug where preset/profile/tune could disappear when reverting a preset.Toolbox for Dynamics CRM 2011/2013: XrmToolBox (v1.2013.9.25): XrmToolbox improvement Correct changing connection from the status dropdown Tools improvement Updated tool Audit Center (v1.2013.9.10) -> Publish entities Iconator (v1.2013.9.27) -> Optimized asynchronous loading of images and entities MetadataDocumentGenerator (v1.2013.11.6) -> Correct system entities reading with incorrect attribute type Script Manager (v1.2013.9.27) -> Retrieve only custom events SiteMapEditor (v1.2013.11.7) -> Reset of CRM 2013 SiteMap ViewLayoutReplicator (v1.201...Microsoft SQL Server Product Samples: Database: SQL Server 2014 CTP2 In-Memory OLTP Sample, based: This sample showcases the new In-Memory OLTP feature, which is part of SQL Server 2014 CTP2. It shows the new memory-optimized tables and natively-compiled stored procedures, and can be used to show the performance benefit of in-memory OLTP. Installation instructions for the sample are included in the file ‘awinmemsample.doc’, which is part of the download. You can ask a question about this sample at the SQL Server Samples Forum Composite C1 CMS - Open Source on .NET: Composite C1 4.1: Composite C1 4.1 (4.1.5058.34326) Write a review for this release - help us improve, recommend us. Getting started If you are new to Composite C1 and want to install it: http://docs.composite.net/Getting-started What's new in Composite C1 4.1 The following are highlights of major changes since Composite C1 4.0: General user features: Drag-and-drop images and files like PDF and Word directly from own your desktop and folders into page content Allow you to install Composite Form Builder ...CS-Script for Notepad++ (C# intellisense and code execution): Release v1.0.9.0: Implemented Recent Scripts list Added checking for plugin updates from AboutBox Multiple formatting improvements/fixes Implemented selection of the CLR version when preparing distribution package Added project panel button for showing plugin shortcuts list Added 'What's New?' panel Fixed auto-formatting scrolling artifact Implemented navigation to "logical" file (vs. auto-generated) file from output panel To avoid the DLLs getting locked by OS use MSI file for the installation.Resources Editor: Resources Editor: Stable releaseWPF Extended DataGrid: WPF Extended DataGrid 2.0.0.10 binaries: Now row summaries are updated whenever autofilter value sis modified.Social Network Importer for NodeXL: SocialNetImporter(v.1.9.1): This new version includes: - Include me option is back - Fixed the login bug reported latelyVeraCrypt: VeraCrypt version 1.0c: Changes between 1.0b and 1.0c (11 November 2013) : Set correctly the minimum required version in volumes header (this value must always follow the program version after any major changes). This also solves also the hidden volume issueCaptcha MVC: Captcha MVC 2.5: v 2.5: Added support for MVC 5. The DefaultCaptchaManager is no longer throws an error if the captcha values was entered incorrectly. Minor changes. v 2.4.1: Fixed issues with deleting incorrect values of the captcha token in the SessionStorageProvider. This could lead to a situation when the captcha was not working with the SessionStorageProvider. Minor changes. v 2.4: Changed the IIntelligencePolicy interface, added ICaptchaManager as parameter for all methods. Improved font size ...New ProjectsASP.NET Web API: ASP.NET Web API is a framework that makes it easy to build HTTP services that reach a broad range of clients, including browsers and mobile devices. ASP.NET WebDungeonPaper: DungeonPaper will be a platform for RPG players to utilize computers to replace traditional pen and paper in their campaigns.EMS: demoEvent Dispatcher: Event Dispatcher is a powershell module for centralized logging. Supports filtering events, and outputs to flat files or the Windows event log.Koopakiller.Numerics: A growing Math-Library for .NET, provided as a portable class library.NetroTrix: NetroTrix is a LAN Messenger Project.....Sharp Explorer: Sort of an alpha Play with C# to make a treeView Windows explorer. Currently multi-threaded dbl click to explore, r-click to preview some text files.TI Sensor Tag Library: A library to access the Texas Instruments Sensor Tag in Windows Store apps with Bluetooth GATT. Written in C#.ULS Log Viewer Feature: "ULS Log Viewer Feature" used by SharePoint Administrators, Developers and SharePoint Site Managers for get easily the real error behind the Correlation ID.Visual Studio Code Line Counter: VS Code Line Counter parses a Visual Studio solution file (.sln), reads each included project, and counts the number of lines in each included file.Vulcanus: TODOWax - The WiX Setup Project Editor: An interactive editor for WiX setup projects.

  Read the article

• Displaying Datamatrix in application error screen

  - by DaveNay

  Quite often we will get a report from a user in the field saying there was an error in our application. Frequently this leads to the typical round of "What was the error?" "I don't know, it was just an error." We of course log these faults to the log files, and we can even enable detailed debug logs, but this involves the end user changing a setting in the configuration file and then finding the correct files and then emailing them to us. As I'm sure you can all imagine, there are plenty of pitfalls and alligators in this methodology. Recently a couple of people have used their cell phone to email me a "screen capture" of the fault, and while this helps, we still have to scrutinize the image to find the exact fault, and if enabled, the stack trace. So this evening, I had the brilliant idea (IMHO) to encode the fault into a Datamatrix barcode image and then encourage users to send me a picture from their cell phone. I can then decode the datamatrix and get a parse-able error message! Our core technology is machine vision, so the decoding of the datamatrix image would be trivial, I just need to find a method of generating the actual image to display in the fault handler. Thoughts?

  Read the article

• Facebook Like javascript related to Time Spent Downloading a page Increase in GWT?

  - by donaldthe

  Hi, I installed the Facebook Like button Javascript version on my website on December 15th. Take a look at this report from Google Webmaster Central. Crawl stats Googlebot activity in the last 90 days The crawl stats are from Googlebot which as far as I know doesn't execute Javascript. Could the Facebook Like Javascript code, "The XFBML version" be related to large spike in Time spent downloading a page? (By the way the huge spike in November was caused by a mistake where every image request was getting a 301.) I'm not sure what caused the spike to go down by half somewhere in December. It may have been related to a faulty setting in web.config. I'm at a loss as to what I can do about this or even how to tell if this is my problem or Googlebots crawl problem. Here is the Facebook code I am using to create the like button. It is right after the opening body tag <div id="fb-root"></div> <script> window.fbAsyncInit = function() { FB.init({appId: 'xxxxx', status: true, cookie: true, xfbml: true}); }; (function() { var e = document.createElement('script'); e.async = true; e.src = document.location.protocol + '//connect.facebook.net/en_US/all.js'; document.getElementById('fb-root').appendChild(e); }()); ` and this creates the like box: <fb:like show_faces="false"></fb:like> If the Javascript can't be the problem any ideas on where to start looking would be appreciated.

  Read the article

• Does it make sense to write build scripts in C++?

  - by Klaim

  I'm using CMake to generate my projects IDE/makefiles, but I still need to call custom "scripts" to manipulate my compiled files or even generate code. In previous projects I've been using Python and it was OK, but now I'm having serious trouble managing a lot of dependencies in two very big projects I'm working on so I want to minimize the dependencies everywhere. Someone suggested to me to use C++ to write my build scripts instead of adding a language dependency just for that. The projects themeselves already use C++ so there are several advantages that I can see: to build the whole project, only a C++ compiler and CMake would be necessary, nothing else (all the other dependencies are C or C++); C++ type safety (when using modern C++) makes everything easier to get "correct"; it's also the language I know the better so I'm more at ease with it even if I'm able to write some good Python code; potential gain in execution speed (but i don't think it will really be perceptible); However, I think there might be some drawbacks and I'm not sure of the real impact as I didn't try yet: might be longer to write the code (that said I'm not sure because I'm efficient enough in C++ to write something that work quickly, so maybe for this system it wouldn't be so long to write) (compilation time shouldn't be a problem for this case); I must assume that all the text files I'll read as input are in UTF-8, I'm not sure it can be easilly checked at runtime in C++ and the language will not check it for you; libraries in C++ are harder to manage than in scripting languages; I lack experience and forsight so maybe I'm missing advantages and drawbacks. So the question is: does it make sense to use C++ for this? do you have experiences to report and do you see advantages and disadvantages that might be important?

  Read the article

• Google Analytics Not tracking data correctly IP-address issue?

  - by PaperThick

  I have developed a small site for a client and the site has been placed inside a <iframe> at the clients site. The GA-script I'm using looks like this: <script type="text/javascript"> var _gaq = _gaq || []; _gaq.push( ['_setAccount', 'UA-XXXXXXXX-2'], //My company's GA-account ['_trackPageview'], ['b._setAccount', 'UA-XXXXXXXX-1'], // Test GA-account ['b._trackPageview'], ['th._setAccount', 'UA-XXXXXXX-3'], ['th._setDomainName', '.clientdomain.se'], // Client GA-account ['th._trackPageview'] ); (function () { var ga = document.createElement('script'); ga.type = 'text/javascript'; ga.async = true; ga.src = ('https:' == document.location.protocol ? 'https://ssl' : 'http://www') + '.google-analytics.com/ga.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(ga, s); })(); </script> </head> As you can see I report the GA pageviews to the client as well. The GA script is tracking visitors and pageviews at both ends. But the problem is that on my clients side the visitor-count is more than double what they are on my end (20 000 vs 5 000). At first I thought that it was being duplicated at some point but when I checked my Crazy-Egg account I saw that it had tracked over 10 000 visits and then stopped tracking because that was my limit on the account. The page my site is on is on a IP-address (http://XXX.XXX.XX.X/campaign/) and not on a "valid url". Could that be an issue why some of the visitors isn't beeing tracked? Thanks in advance

  Read the article

• Eliminating zero-length files

  - by RhZ

  I have been having multiple crashes recently. 4-5 last night within a few hours. I posted about it before, and got an answer but not sure how to proceed. The messages in my logs right before the crash are multiple complaints about valid eCryptfs headers. But the chron might not be related, I don't think I saw that in previous crashes: xxx-desktop kernel: [ 1112.274474] Valid eCryptfs headers not found in file header region or xattr region, inode 32376924 xxx-desktop CRON[4212]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) So I was sent to an answer providing this script: for i in find $(mount | grep " on $HOME type ecryptfs" | awk '{print $1}') -size 0c; do if ! fuser -v $i; then rm -f $i fi done I did find some zero byte files, not in the exactly right place (a folder called .private as I remember), but I need to fix this, its too bad right now. So I need to delete any of them that are not in use. I am a little too clueless, can someone walk me through executing this script? I don't know how.

  Read the article

• Where I'll Be At JavaOne 2012

  - by Geertjan

  Fun and games for me at JavaOne 2012. Below are the sessions/BOFs/tutorials I'll be attending. The items in red are the sessions and BOFs where I'll be speaking, either as the main/only speaker or as a supporting speaker in someone else's presentation, while the other items (except for the NetBeans booth duties and mini presentations, which are included below) are items I'm interested in and so will be sitting in the audience: Sunday: NetBeans Day Monday: 10:00 - 12:00 TUT4801: Make Your Clients Richer: JavaFX and the NetBeans Platform 12:20 - 12:30 Mini Presentation in OTN Lounge: What's New in NetBeans IDE? 13:00 - 14:00 CON7050: How My Life Would Have Been So Much Better If We Had Used the NetBeans Platform 14:30 - 14:40 Mini Presentation in OTN Lounge: NetBeans and Java EE 15:00 - 16:00 CON4038: Project EASEL: Developing and Managing HTML5 in a Java World 16:30 - 17:15 BOF6151: NetBeans.Next: The Roadmap Ahead 17:30 - 18:15 BOF3332: Lessons Learned in Writing a PDF-to-JavaFX Converter for NetBeans 18:30 - 19:15 BOF4920: Runtime Class Reloading for Dummies Tuesday: 9:30 - 11:30 NetBeans Booth 11:30 - 12:30 CON6139: Lessons Learned in Building Enterprise and Desktop Applications with the NetBeans IDE 13:00 - 14:00 CON4387: Bringing Mylyn to NetBeans and OSGi, Bridging Their Worlds 14:30 - 14:40 Mini Presentation in OTN Lounge: NetBeans Java Editor 15:30 - 17:30 NetBeans Booth 17:30 - 18:15 BOF3665: Custom Static Code Analysis 18:30 - 19:15 BOF5806: Doing JSF Development in the NetBeans IDE  Wednesday: 8:30 - 9:30 CON5132: NetBeans Plug-in Development: JRebel Experience Report 10:00 - 11:00 CON2987: Unlocking the Java EE 6 Platform 11:30 - 12:30 CON10140: Delivering Bug-Free, More Efficient Code for the Java Platform 13:00 - 14:00 CON3826: Patterns for Modularity: What Modules Don’t Want You to Know 14:30 - 14:40 Mini Presentation in OTN Lounge: NetBeans Platform 15:00 - 16:00 CON3160: Dynamic Class Reloading in the Wild with Javeleon Thursday: 12:30 - 13:30 CON4952: NetBeans Platform Panel Discussion 14:00 - 15:00 CON11879: Getting Started with the NetBeans Platform There are several sessions/BOFs I would have liked to be able to attend, but because of clashes with other sessions that I need to see slightly more urgently, I won't be able to attend those, unfortunately. Will be a busy but interesting time, as always! The entire list of NetBeans-oriented sessions can be found here: http://netbeans.org/community/articles/javaone/2012/index.html

  Read the article

• R12 Diagnostic Script for Purchasing Encumbrance Issues

  - by Oracle_EBS

  Do you have a Release 12 Purchasing document with an accounting encumbrance error?  Get all the relevant data in one step using the new diagnostic in DOC ID: 1483743.1 -  ‘R12: Diagnostic Script to help troubleshoot Purchasing Encumbrance Issues’.   Avoid the back and forth pinging with support for data collection.   Query the document id in My Oracle Support and add it to your Favorites using the star icon for quick access. The note includes when to use the script and how to use it.  The script will produce a user friendly html output that contains information relevant to encumbrance issues, along with some data validation checks to identify common data corruption issues on your document.  For example in this one diagnostic it will provide information on the following: Ø Cross Product Setup Ø Document Data Dump Ø Funds availability Ø Subledger accounting information Ø GL and AP Invoice Data Ø Debug and Trace This output is ideal for self service, as it provides known issues in the Data Validation section (related to the document) with links to key documentation.   Or the report can be uploaded to support when logging a Service Request. To see more about the diagnostic, attend our September 11, 2012 Webcast ‘Overview of Procurement Patching and New Tools for Issue Resolution’.  Visit Doc ID 1479718.1 to signup.  Note: This topic will not be listed as it has been just added.

  Read the article

• xubuntu 12.04 screen regularly stops refreshing, refreshing resumes after un-/re-maximizing a window

  - by user68477

  My screen frequently stops completely refreshing. I can make it resume refreshing by un-maximizing/re-maximize a window or by switching workspace (the un-/re-maximizing works every time. Switching workspace sometimes has to be done a couple of times). The immediate impression is that the system is frozen: there is apparently no reaction to anything I do but interestingly window title bar will change, if I switch application with (i.e alt+tab or browse through folders) I saw an identical issue in ubuntu 10.04, though a lot less frequent, I never saw this in ubuntu 12.04 (which I have been using the last 4-5 months). After switching to Xubuntu I'm seeing this again and more frequently. The specific reason I'm not sure this is a bug: I installed gnome-control-center which dragged in tons of packages. This was while trying to fix dual-screen setup. I believe the issue surfaced after this. I later meticulously removed every package from this batch (purge) in the hope that every setting would also be removed. But the issue has persisted. Another issue happened at the same time, it may be totally unrelated but it feels as if it is the same basic issue: the screen resolution of the greeter became less than the expected 1680x1050 and often after login there's just a blank and totally unresponsive wallpaper without panel so I have to force reboot. When the login is successful it's very clear that it works hard to determine the correct resolution which is achieved after a few blink to black screens. My questions: 1) Is this a settings issue or a bug? 2) How do I begin to research the issue - could I perhaps some way reset xubuntu/xfce to default. 3) If this is a bug where would be the most appropriate place report this? System: Thinkpad T500 ati radeon HD 3650 $ fglrxinfo display: :0.0 screen: 0 OpenGL vendor string: Advanced Micro Devices, Inc. OpenGL renderer string: ATI Mobility Radeon HD 3650 OpenGL version string: 3.3.11627 Compatibility Profile Context $ uname -a Linux srvname 3.2.0-32-generic #51-Ubuntu SMP Wed Sep 26 21:33:09 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux xfce 4.10 Compiz 0.9.7.8

  Read the article

< Previous Page | 203 204 205 206 207 208 209 210 211 212 213 214  | Next Page >