Search Results

Search found 11524 results on 461 pages for 'insurance networking news'.

Page 209/461 | < Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >

• why udp client work when wirshark capture?

  - by herzl shemuelian

  I have two machine A,B windows 7 os .I connect them end to end and try run a performance test by using tcpreplay. step 1) I check conectivity between to point by netcat In A i run nc -lvup 5432 when I run on B nc -u 1.2.3.4 5432 I can send data from B to A step 2) when in I run tcpreplay in B tcpreplay -i %0 myudp.pcap in A I don't recevice any data . when I open wireshark in A then my nc can read data why? I check dst mac and dst ip in pcap file they are correct. is importan udp src mac or src ip for udp how that I open udp server ?

  Read the article

• Wireless Network Performance Issues

  - by colithium

  My brand new Dell XPS system has been running flawlessly except its abysmal download speeds. I have tried isolating every variable I could possibly think of but I can't figure out the problem. I've talked to Dell and Belkin without making progress (thought I'd try). Here are the speeds: Note that most of the time, upload speeds are actually much faster than download speeds (around 4.0 Mb/s which is better than most other devices on the network) It's not the ISP. The slowdown happens even when transferring files inside the network. Plus every other wireless device gets approximately this: It's not the wireless router. It's a Lynksis WRT160N v1 with the latest firmware (1.02.2). Plus everything else connected to it has normal speeds. It's not the browser. Speeds are the same in IE, FF, and when transferring files with Windows between computers. It's not the wireless adapter. I've tried a Belkin N Wireless USB Adapter (which works fine on another computer) and a Dell Wireless Draft 802.11n WLAN Mini-Card. They have the same slow speeds when connected to the problem computer. It's not the adapter connection. One adapter used USB and the other is a Mini-Card. It's not antenna placement. With the same antenna position and the same device, I get different speeds when connected to the problem computer vs a good computer. Plus everything reports the connection speed as at least 11Mbps and good signal strength. I've tried disabling IPv6 since it sometimes causes weird problems. I've tried disabling Windows Firewall/anti-virus. I've ensured the computer has updated drivers for both adapters. I've ensured that Windows is up to date and so is the BIOS. For the USB adapter I ensured that that USB port functioned at normal speeds with other USB devices. What else could it possibly be? I finally received my copy of Windows 7 and will be trying that. I'd rather not install Windows 7 because of a particular program that will stop working so a solution besides that is welcome. Specs: Vista x64 Core i7 920 6GB RAM 500GB HD GTX 260

  Read the article

• Windows 7 Wireless Network Adapter Stopped Working

  - by Andrew B Schultz

  I have a Windows 7 Ultimate machine where the wireless adapter all of a sudden started having trouble connecting to wireless networks. Whenever I go to a new place and try to connect to a wireless network, it says that the DNS server is not responding, and tells me to go unplug the router and try again. After several locations in a row telling me this, I began to realize something was wrong with my adapter, not the routers. I am no longer asked to identify the security level for any new networks (Work, Home, or Public) like I used to be (it defaults to Public now - with the park bench icon). Often, resetting the router doesn't even work. Running the Windows 7 troubleshooter doesn't give me anything better than the advice to reset the router. However, the adapter will still connect to the wireless network at my main office without any problems. Does anyone know why a wireless network adapter can get so finicky so suddenly? Thanks!

  Read the article

• Why does my DD-WRT not accept SSH connections from my laptop?

  - by Vlad Seghete

  So, here is my system: I have a 2Wire AT&T modem/router which I use for wireless and a Buffalo router flashed with DD-WRT which is physically attached to the 2Wire and set in the DMZ. I set everything up on the DD-WRT to be able to connect to it using ssh and also so that it forwards ssh requests on a different port to one of the servers behind it. Now, when I am physically connected to the DD-WRT all this works great and as I would want it to. I ssh into the two different ports using the WAN IP of my network, and I get where I expect to land. If, however, I am connected using wi-fi to the 2Wire, the same commands do not work. I do not get an error, simply a timeout. I have trouble understanding this, since the DD-WRT is set in the DMZ and everything should pass to it. To further complicate the problem, I tried connecting to the same IP using my phone (wireless disabled, so really from the WAN) and surprise, it works! If I go back on the local network by enabling the wifi, the ssh connection times out. To make this even stranger, my WAN IP address always responds to pings (meaning in all the above situations). What could be going on here? I know what I should do, completely disable the 2wire as a router and use it strictly as a modem and them use all the routing capabilities of the dd-wrt. It's what I will probably end up doing anyway, but my question remains, because I really want to know what is happening here.

  Read the article

• Load Balancing a UDP server

  - by Hellfrost

  Hello StackOverflow, I have a udp server, it is a central part in my business process. in order to handle the loads I'm expecting in the production environment I'll probably need 2 or 3 instances of the server. The server is almost entirely stateless, it mostly collects data, and the layer above it knows how to handle the minimal amount of stale data that can arise from the the multiple server instances. My question is, how can I implement load balancing between the servers? I would prefer to distribute the requests as evenly as possible between the servers. I would also would like to have some fidelity, I mean if client X was routed to server y, then I want all of X's subsequent requests to go to server Y, as long as it is sensible and not overloads Y. By the way it is a .NET system... what would you recommend?

  Read the article

• Sharing internet connection from Windows XP using wi-fi router

  - by Darius

  Hi, I have an network configuration like: Ethernet cable from ISP connected to Windows XP machine, configured with static IP 192.168.0.3 Another ethernet connection from 2nd Windows XP machine's network adapter to a Wi-Fi router (D-Link Airport G+) XP set to "Share internet connection", the 2nd adapter configured as static to 192.169.0.1 D-Link Airport Wi-Fi router also configured as "static connection", it's IP set to 192.169.0.2, default gateway set to 192.169.0.1. Network mask everywhere is 24. Laptop computer connected with the router with static IP 192.169.0.3 The problems are: XP machine sees the router (it's able to ping it and access it via the web admin tool) The router somehow cannot PING the XP machine (using the tool provided by the web-based admin tool) The laptop computer cannot ping anything and cannot be pinged The router is only accessible when the ethernet cable is connected with a router's 1-4 LAN port, when I connect it via "WAN" port (which I believe is the proper one) it's not visible from the XP machine If you have similar experience with configuring a network like this I would really appreciate your help. I cannot use the Wi-Fi router with the ISP cable itself.

  Read the article

• Kickstart: ifcfg-eth0 file genorated by kickstart when install from network but from initrd when install form USB

  - by dooffas

  When I install Fedora 19 with a kickstart file and via network, the generated ifcfg-eth0 file is genorated by the kickstart: # Generated by parse-kickstart However if I use the same kickstart file and install via a USB stick, the ifcfg file is generated by initrd. # Generated by dracut initrd The line in the kickstart file to set the network settings is as follows: network --device=eth0 --bootproto=dhcp --hostname=SOMEHOSTNAME Is there away to keep network device settings set in the kickstart file when not installing via network?

  Read the article

• A website hosted on the 1.0.0.0/8 subnet, somewhere on the Internet?

  - by Dave Markle

  Background I'm attempting to demonstrate, using a real-world example, of why someone would not want to configure their internal network on the 1.0.0.0/8 subnet. Obviously it's because this is not designated as private address space. As of 2010, ARIN has apparently allocated 1.0.0.0/8 to APNIC (the Asia-Pacific NIC), who seems to have begun assigning addresses in that subnet, though not in 1.1.0.0/16, 1.0.0.0/16, and others (because these addresses are so polluted by bad network configurations all around the Internet). My Question My question is this: I'd like to find a website that responds on this subnet somewhere and use it as a counter-example, demonstrating to a non-technical user its inaccessibility from an internal network configured on 1.0.0.0/8. Other than writing a program to sniff all ~16 million hosts, looking for a response on port 80, does anyone know of a directory I can use, or even better yet, does anyone know of a site that's configured on this subnet? WHOIS seems to be too general of a search for me at this point...

  Read the article

• VM can't connect to outside in bridged mode

  - by Kamal

  Hi Guys, I am not able to ping any machine(not even the host) from Guest VM in bridged mode. But I got an IP which is on the same subnet as host. I can ping my guest VM from the host and can use ssh to connect to the guest. I am using Vmware workstation 6.5. Guest VM is a centos VM and host is windows xp. Every thing works fine in NAT mode. Any clues as to what could be happening. I tried disabling all the firewalls I have.

  Read the article

• Why the VPN Network Shake-Up?

  - by Brent Arias

  I can RDP to another machine on my home network, only if I'm not also hooked up to my employer's VPN with the Cisco VPN client. Indeed, I can't even ping the other machine by name in this mode, because ICMP suddenly thinks that ( ping myMachine ) now means ( ping myMachine.myEmployer.com ). Of course there is no machine by that latter name, and so it fails. Even weirder, once I disconnect from the VPN I can again ping myMachine successfully, but ICMP reports the machine by its MAC address instead of its IP address. I don't think I've ever seen ping identify another machine by its MAC address. So two questions: How can I access via RDP/ping the other machine BY NAME on my local network while also connected to the VPN? Why is ping identifying a MAC address for the machine on my home network, instead of an IP address? And how can I change this so that an IP address is reported instead? For question #1, I can indeed access the other machine on my home network by IP address. I suspect if I put the name-IP pair into my HOSTS file, then I would be able to access it even when connected to the VPN. But I wonder if there is another (more elegant) solution?

  Read the article

• Windows - Force Wi-Fi to N mode

  - by Frederick Marcoux

  I bought a month ago the D-Link DWA-160 Xtreme N Dual Band USB Adapter and I wonder about the speed. I have a 60Mbps but the speed is never above 300Kbps when I browse Internet or download something. Even from Microsoft or Apple (the fastest server I found). Now on Windows 8, we can see the Wi-Fi stats in Task Manager, there they are: Notice the red rectangle. The signal is 3/5 and I'm about 5 meters far from my router. An Apple Time-Capsule. Also, the connection type is 802.11g, I want N. I made this config in my Device Properties: Does anyone figured out to force the 802.11n in Windows? (Windows 8 preferably)

  Read the article

• Is there a simple way to detect ISP port blocking?

  - by Will M

  Is there a way to tell the difference between my ISP blocking traffic on certain ports and my NAT router/firewall blocking that traffic? The sites “Shields Up” and “Can you see me” show my ports closed or not accessible, but I assume that is primarily due to the NAT router. (Obviously, I could just remove the router, connect directly and use those sites, but is there a simple way to test without doing that?)

  Read the article

• Time-Machine backup over SSH tunnel to NFS mount

  - by BTZ

  I've recently started using a new NAS which runs CentOS 6.2. One of the purposes of the NAS would be to serve as a backup target. Whilst I have been using Apple's Time-Machine for a while and I am very satisfied with it, I'd like to continue using it. Backing up directly to an address in my network is no hassle; all works fine. For security reasons I'd like all my traffic to go through an ssh tunnel to the NAS. This way I can avoid needing to get a VPNserver (for personal reasons). As of NFSv4 the NFS deamon is bound to port 2049, which makes it easy for me to direct all traffic through a ssh tunnel. Tunnel: ssh -f admin@ms -L 2000:localhost:2049 -N Mount: mount -t nfs -o nfsvers=4,rw,proto=tcp,sync,intr,hard,timeo=600,retrans=10,wsize=32768,rsize=32768,port=2000 localhost:/mac_backup /Volumes/backup This works fine for Finder/terminal and throughput is almost equal to direct traffic. (CPU of the NAS does ride high when I reach max bandwidth though) Now the problem: With Time-Machine I can't use the NFS mount point mounted on localhost. TM seems to try to connect to it and then give me a "OSStatus error 65". I also tried using NFSv3 (I correctly forwarded all ports) with no luck. Can anyone shed a light on this and/or give a solution?

  Read the article

• How to add a broadcast address to loopback with ifconfig on a OS/X?

  - by chrisapotek

  I am trying to use ifconfig to turn on broadcast on my loopback interface. It currently reads: lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 As you can see, no broadcast address! :( :( :( I tried this on OS/X but it did not work and it did not give any error or feedback: ifconfig lo0 broadcast 127.255.255.255 Any guru would know that? I have one server that sends one packet. I have two clients running on the same machine as the server. I need them to pick up the packet WITHOUT having to force the server to send it twice.

  Read the article

• /etc/hosts.deny ignored in Ubuntu 14.04

  - by Matt

  I have Apache2 running on Ubuntu 14.04LTS. To begin securing network access to the machine, I want to start by blocking everything, then make specific allow statements for specific subnets to browse to sites hosted in Apache. The Ubuntu Server is installed with no packages selected during install, the only packages added after install are: apt-get update; apt-get install apache2, php5 (with additional php5-modules), openssh-server, mysql-client Following are my /etc/hosts.deny & /etc/hosts.allow settings: /etc/hosts.deny ALL:ALL /etc/hosts.allow has no allow entries at all. I would expect all network protocols to be denied. The symptom is that I can still web browse to sites hosted on the Apache web server even though there is a deny all statement in /etc/hosts.deny The system was rebooted after the deny entry was added. Why would /etc/hosts.deny with ALL:ALL be ignored and allow http browsing to sites hosted on the apache web server?

  Read the article

• Unable to access certain websites from a computer

  - by matt74tm

  One of the desktop computers in my office is unable to access some particular websites. We've tried from Chrome, IE, Firefox, but no luck. eg: http://spsims.wto.org/ -> click on "Regular notifications" On the affected computer, every browser times out after the click. Whereas it should redirect the user to http://spsims.wto.org/web/pages/search/notification/regular/Search.aspx How can I diagnose this further? This is a Windows XP machine.

  Read the article

• Tomato/DD-WRT router to act as switch & only NAT some port

  - by fseto

  BACKGROUND: I have a device that must use a real IP address. Currently, my ISP uses DHCP and I can have up to 4 real IP address assigned. However, the cable modem only have 1 ethernet port and it's connected to my router (running Tomato, but can run DD-wrt or other Openwrt if required). Question stems from how I can connect the additional device, requiring a real IP? EASY SOLUTION: would be to get a switch and connect to the CM, Router, and Device. But alas, I want to avoid this route, since: my wiring cabinet in my home is drawing lots of power and heat already Device will be unprotected by any firewall unable to monitor the traffic to/from device. Besides, what would be the FUN in that? =) IDEA: So what I want to do is to configure the router, so that one of the switchport is removed from the normal br0 bridge. Instead, I want to make it behave like a switch on the WAN port. What's the best way of doing this? Should I create another bridge on the WAN & the device port? Can a single port belongs to two bridges? or would I need to create a subinterface first? Would I need a DHCP-relay? Am I expecting too much from my poor cheapie router? +------+ | CM | +--++--+ || +----WAN---------------+ | / \ Router | | BR1? BR0 | | | \ | | | {NAT} | | | / | | \ | +-P0----P1-P2-P3-Wifi--+ | +------+ |Device| +------+

  Read the article

• Getting rid of your server in a small business environment

  - by andygeers

  In a small business environment, is it still necessary to have a central server? Speaking for my own company (a small charity with about 12 employees) we use our server (Windows Server 2003) for the following: Email via Microsoft Exchange Central storage Acting as a print server User authentication / Active Directory There are significant costs associated with running a server like this: Electricity, first for the server itself then for the air conditioning required (this thing pumps out a lot of heat) Noise (of which there is a lot) IT support bills (both Windows Server and Exchange are pretty complicated, and there are many ways they can go wrong) I've found ways to replace many of these functions with cheaper (better?) alternatives: Google Apps / GMail is a clear win for us: we have so many spam related problems it's not even funny, and Outlook is dog slow on our aging computers You can buy networked storage devices with built in print servers, such as the Netgear ReadyNAS™ RND4210 that would allow us to store/share all of our documents, and allow us to access printers over the network The only thing that I can't figure out how to do away with is the authentication side of things - it seems to me that if we got rid of our server, you'd essentially have a bunch of independent PCs that had no shared pool of user accounts / no central administrator. Is that right? Does that matter? Am I missing any other good reasons to keep a central server? Does anybody know of any good, cost-effective ways of achieving the same end but without the expensive central server?

  Read the article

• Login to wireless network with WPA password on Ubuntu Server

  - by Mr. Man

  Is it at all possible to login to a wireless network with a WPA password on Ubuntu Server with no Window System? Thanks in advance!

  Read the article

• How can I print from my lion mac mini to my windows XP, with simple file sharing?

  - by Jules

  I have quite a complicated setup, perhaps. And a lot of history on this issue, I'm hoping that I don't have to buy a new printer. I've got a HP Wireless USB Print Server, which requires client software, I can't just use it as an IP Printer. The HP software is pretty poor on the mac and is no longer supported and often locks up the printer server and takes some considerable effort to actually print something. Let alone if a windows machine attaches to it first. My printer is an Epson Stylus R285. However, the windows client software is fine and we can print from windows 7 / XP without problem. We have simple file sharing setup as this is the only way I could get windows XP to talk to windows 7. However, I can't seem to get my mac mini to connect as anything other than a guest to my xp machine, to connect to the shared printer. I'm not considering some kind of internet printing as this would seems the simplest solution. But I'm not sure what will work with my setup ?

  Read the article

• TCPDump and IPTables DROP by string

  - by Tiffany Walker

  by using tcpdump -nlASX -s 0 -vvv port 80 I get something like: 14:58:55.121160 IP (tos 0x0, ttl 64, id 49764, offset 0, flags [DF], proto TCP (6), length 1480) 206.72.206.58.http > 2.187.196.7.4624: Flags [.], cksum 0x6900 (incorrect -> 0xcd18), seq 1672149449:1672150889, ack 4202197968, win 15340, length 1440 0x0000: 4500 05c8 c264 4000 4006 0f86 ce48 ce3a E....d@[email protected].: 0x0010: 02bb c407 0050 1210 63aa f9c9 fa78 73d0 .....P..c....xs. 0x0020: 5010 3bec 6900 0000 0f29 95cc fac4 2854 P.;.i....)....(T 0x0030: c0e7 3384 e89a 74fa 8d8c a069 f93f fc40 ..3...t....i.?.@ 0x0040: 1561 af61 1cf3 0d9c 3460 aa23 0b54 aac0 .a.a....4`.#.T.. 0x0050: 5090 ced1 b7bf 8857 c476 e1c0 8814 81ed P......W.v...... 0x0060: 9e85 87e8 d693 b637 bd3a 56ef c5fa 77e8 .......7.:V...w. 0x0070: 3035 743a 283e 89c7 ced8 c7c1 cff9 6ca3 05t:(>........l. 0x0080: 5f3f 0162 ebf1 419e c410 7180 7cd0 29e1 _?.b..A...q.|.). 0x0090: fec9 c708 0f01 9b2f a96b 20fe b95a 31cf ......./.k...Z1. 0x00a0: 8166 3612 bac9 4e8d 7087 4974 0063 1270 .f6...N.p.It.c.p What do I pull to use IPTables to block via string. Or is there a better way to block attacks that have something in common? Question is: Can I pick any piece from that IP packet and call it a string? iptables -A INPUT -m string --alog bm --string attack_string -j DROP In other words: In some cases I can ban with TTL=xxx and use that should an attack have the same TTL. Sure it will block some legit packets but if it means keeping the box up it works till the attack goes away but I would like to LEARN how to FIND other common things in a packet to block with IPTables

  Read the article

• Network access lags for Win7 when server network utilization is high

  - by Jeff Miles

  We have a Dell PE2950 file server running Windows 2008, hosting a DFS namespace of ~1.2 TB. This server has two Broadcom 1Gbps NICs teamed together. When there is high traffic going to the server across the network (greater than 200 Mbps), any Windows 7 client accessing a DFS share at the time experiences severe performance problems. For example: Computer A has an AutoCAD drawing opened directly from the DFS share. Performance is normal, not causing any issues. Computer B begins a file transfer, putting a 11GB file onto a different DFS namespace, on the same server Computer A immediately notices lag while using AutoCAD. The cursor momentarily freezes within AutoCAD every 10 seconds or so, and any browsing of the DFS share is extremely slow. Computer B completes file transfer, and performance resumes to normal for Computer A. This is only affecting Windows 7 clients, using a variety of hardware (desktop + laptop). All of our Windows XP clients see no performance impact during the file transfer. Things I have tried with no change: Had Computer A work from an entirely different RAID array from the file transfer destination Updated NIC drivers on clients and server Enabled TCP offload and receive side scaling on the server NIC (previously disabled when the issue began) Antivirus disabled during file transfer I am currently having a user test applications other than AutoCAD when the file transfer occurs, and will update the question with that result. Does anyone have any recommendations for resolution or additional troubleshooting steps?

  Read the article

• Is it possible to add an existing Azure VM to an Azure Virtual Network?

  - by Dan Harris

  Didn't think this was directly related to programming, so thought Superuser would be better than Stack Overflow.... Is it possible to add an existing Azure VM to an Azure Virtual Network if you didn't add it to the virtual network at the time of creation? I can't see an option to change which Virtual Network the VM is connected to. Do you just have to do it at the time you create the VM, and if you don't do it then you will need to re-create the VM and delete the existing one? Example of the scenario: No VM's or Virtual Networks exist I create a VM (VM1), there is no virtual network so it isn't added to one Later I create a Virtual Network in Azure (Network1) It is possible to create another VM (VM2) and connect it to the Virtual Network (Network1), but can I connect VM1 to Network1 or must I delete VM1 and re-create it to get it connected to Network1?

  Read the article

• "DNS not responding" error with D-Link router and PPTP internet connection

  - by Born2win

  I have a D-Link DIR-615 router since around six months. My internet connection is VPN (PPTP) based, i.e. I have been given a username and password from my ISP and my IP address is dynamic. Since a few days I am experiencing a serious problem. My router connects normally (I can see the yellow light), but my computer is giving me a "DNS not responding" error. I have tried everything (reset, reboot etc.) but no success.

  Read the article

• How can we connect TP-link Access Point- TL-WA5210G with Wifi Lan card?

  - by PPS

  I would like to know that, We have a small Wireless Network that covers 40 mtrs indoor. Now we plan to expand our Network Coverage area apporx. 200 Mtrs (Outdoor). Due to our requirement we used TP- Link Access Point TL-WA5210G Outdoor(This AP covers 15Km area). We have 3 blocks between 200 mtrs, We like to connect all the laptops Lan Card directly with required Access-point. What should we do to achieve this, right now we are not getting the full strength signal, when we cross the 80 mtrs. So please suggest me proper configuration for implementing this TP-Link access point. Thanks PPS

  Read the article

< Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >