Search Results

Search found 10397 results on 416 pages for 'mobile devices'.

Page 209/416 | < Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >

  • Hyper-V Network Boot Legacy Network

    - by Carl
    Hi, I am planning out a Hyper-V R2 Cluster environment. I was wondering if I went to the effort of deploying one of the few methods to network boot from iSCSI inside the guests, whether the legacy network adapter would switch to a synthetic after boot, or whether the connection could be handed to a synthetic network after boot? This is obviously for performance reasons. MS suggests that some emulated devices are capable of switching to synthetic with integration services after boot, but doesn't specifically list all which are capable.

    Read the article

  • Mac - Windows VPN

    - by user61652
    Hi, I am trying to setup a secure vpn server (Ipsec l2tp) on windows so I can connect to it using my mobile mac or any other windows pc. It seems it is quite a hassle to do this. Does anyone have any good suggestions, maybe a software or open source. Note that I have not yet encountered a piece of ware that can run on both windows and mac. I would ideally prefer a single UI rather than learn two. BR

    Read the article

  • Utility for easily disabling/enabling extra hard drives?

    - by SkippyFire
    I just got an Asus G60 laptop, and will be installing an SSD as the primary, and will use the existing HDD as a storage drive. Is there a utility that I can use to turn off/disconnect the storage drive when I'm not using it? Mainly, I want to be able to conserve power when I'm mobile, since the battery life of this laptop is pretty weak. Thanks in advance!

    Read the article

  • WiFi connection help(Kali Linux)

    - by LoganR
    Ok so here's my problem. I CAN connect to my router using my passphrase. Everything goes through just fine, but I can't use anything that requires an internet connection (apt-get, Iceweasel). My router is properly configured as all other devices work fine. I can't even get into my router's configuration page or view anything else on the LAN. Also, yes I'm sure the security type is set to the correct type.

    Read the article

  • How to activate Virtual Desktop on Fortigate 100A ?

    - by Deniz
    We did recently update the firmware on our Fortigate 100A box and after the upgrade we tried to use the "Virtual Desktop" feature. (This isn't a new firmware feature) We can't find a way to activate or use it. Does anyone have any experience on "Virtual Desktop" of Fortigate devices ?

    Read the article

  • Windows 7 Audio Mixer - Alternative?

    - by barfoon
    Hey everyone, Does anyone know of an app that could serve as an alternative to the mixer in Windows 7? I am looking to quickly adjust the volume of various devices easily (preferably with a keystroke to open the panel perhaps?). If anyone knows of any other tools/shortcuts, please post them here. Thanks!

    Read the article

  • High I/O latency with software RAID, LUKS encrypted and LVM partitioned KVM setup

    - by aef
    I found out a performance problems with a Mumble server, which I described in a previous question are caused by an I/O latency problem of unknown origin. As I have no idea what is causing this and how to further debug it, I'm asking for your ideas on the topic. I'm running a Hetzner EX4S root server as KVM hypervisor. The server is running Debian Wheezy Beta 4 and KVM virtualisation is utilized through LibVirt. The server has two different 3TB hard drives as one of the hard drives was replaced after S.M.A.R.T. errors were reported. The first hard disk is a Seagate Barracuda XT ST33000651AS (512 bytes logical, 4096 bytes physical sector size), the other one a Seagate Barracuda 7200.14 (AF) ST3000DM001-9YN166 (512 bytes logical and physical sector size). There are two Linux software RAID1 devices. One for the unencrypted boot partition and one as container for the encrypted rest, using both hard drives. Inside the latter RAID device lies an AES encrypted LUKS container. Inside the LUKS container there is a LVM physical volume. The hypervisor's VFS is split on three logical volumes on the described LVM physical volume: one for /, one for /home and one for swap. Here is a diagram of the block device configuration stack: sda (Physical HDD) - md0 (RAID1) - md1 (RAID1) sdb (Physical HDD) - md0 (RAID1) - md1 (RAID1) md0 (Boot RAID) - ext4 (/boot) md1 (Data RAID) - LUKS container - LVM Physical volume - LVM volume hypervisor-root - LVM volume hypervisor-home - LVM volume hypervisor-swap - … (Virtual machine volumes) The guest systems (virtual machines) are mostly running Debian Wheezy Beta 4 too. We have one additional Ubuntu Precise instance. They get their block devices from the LVM physical volume, too. The volumes are accessed through Virtio drivers in native writethrough mode. The IO scheduler (elevator) on both the hypervisor and the guest system is set to deadline instead of the default cfs as that happened to be the most performant setup according to our bonnie++ test series. The I/O latency problem is experienced not only inside the guest systems but is also affecting services running on the hypervisor system itself. The setup seems complex, but I'm sure that not the basic structure causes the latency problems, as my previous server ran four years with almost the same basic setup, without any of the performance problems. On the old setup the following things were different: Debian Lenny was the OS for both hypervisor and almost all guests Xen software virtualisation (therefore no Virtio, also) no LibVirt management Different hard drives, each 1.5TB in size (one of them was a Seagate Barracuda 7200.11 ST31500341AS, the other one I can't tell anymore) We had no IPv6 connectivity Neither in the hypervisor nor in guests we had noticable I/O latency problems According the the datasheets, the current hard drives and the one of the old machine have an average latency of 4.12ms.

    Read the article

  • Using USB HDD with Arcserve / Brightstor

    - by Hilt86
    I am having an issue configuring a standard USB HDD for use with CA Arcserve Brightstor 11.5 SP2 : Under the device list it shows a USB device category but none of my USB drives are listed underneath. I have attempted to "scan devices" but it makes no difference. I have also tried restarting the tape engine to no avail! Is anyone successfully using USB drives with Brightstor?

    Read the article

  • How to make the PC speaker beep from the Windows 7 command prompt?

    - by oKtosiTe
    I'm running some lengthy video encodes using the Handbrake command line interface. After all my encodes are done, I would like to have the PC speaker beep, as I usually turn my large external speakers off. On Linux I would install the "beep" package, but so far I haven't found such a program for Windows 7. Possibly related links: System "Beep" sound does not function in Windows Vista x64 with HD Audio devices (I am indeed using an HD Audio device: the SoundMAX ADI1986A) What’s up with the Beep driver in Windows 7?

    Read the article

  • Windows 7 - wireless connection sharing

    - by Chris Ballance
    I am trying to share my mobile broadband internet connection with other machines via wifi and am running windows 7. Users are able to connect to my machine, but not able to obtain an internet connection once they connect to me. Any ideas would be very helpful. Does Windows firewall block this?

    Read the article

  • Looking for a good SNMP Browser to run under windows

    - by Littlejon
    I used to use Getif for poking around inside SNMP results from servers and devices. However it no longer works with Windows 7 and 64bit. I am looking for hopefully an OpenSource bit of software that will allow me add MIB's as required and allow me to browse the MIB tree and send a request/walk off to a server to get results. What do you all use?

    Read the article

  • Solution to route/proxy SNMP Traps (or Netflow, generic UDP, etc) for network monitoring?

    - by Christopher Cashell
    I'm implementing a network monitoring solution for a very large network (approximately 5000 network devices). We'd like to have all devices on our network send SNMP traps to a single box (technically this will probably be an HA pair of boxes) and then have that box pass the SNMP traps on to the real processing boxes. This will allow us to have multiple back-end boxes handling traps, and to distribute load among those back end boxes. One key feature that we need is the ability to forward the traps to a specific box depending on the source address of the trap. Any suggestions for the best way to handle this? Among the things we've considered are: Using snmptrapd to accept the traps, and have it pass them off to a custom written perl handler script to rewrite the trap and send it to the proper processing box Using some sort of load balancing software running on a Linux box to handle this (having some difficulty finding many load balancing programs that will handle UDP) Using a Load Balancing Appliance (F5, etc) Using IPTables on a Linux box to route the SNMP traps with NATing We've currently implemented and are testing the last solution, with a Linux box with IPTables configured to receive the traps, and then depending on the source address of the trap, rewrite it with a destination nat (DNAT) so the packet gets sent to the proper server. For example: # Range: 10.0.0.0/19 Site: abc01 Destination: foo01 iptables -t nat -A PREROUTING -p udp --dport 162 -s 10.0.0.0/19 -j DNAT --to-destination 10.1.2.3 # Range: 10.0.33.0/21 Site: abc01 Destination: foo01 iptables -t nat -A PREROUTING -p udp --dport 162 -s 10.0.33.0/21 -j DNAT --to-destination 10.1.2.3 # Range: 10.1.0.0/16 Site: xyz01 Destination: bar01 iptables -t nat -A PREROUTING -p udp --dport 162 -s 10.1.0.0/16 -j DNAT --to-destination 10.3.2.1 This should work with excellent efficiency for basic trap routing, but it leaves us completely limited to what we can mach and filter on with IPTables, so we're concerned about flexibility for the future. Another feature that we'd really like, but isn't quite a "must have" is the ability to duplicate or mirror the UDP packets. Being able to take one incoming trap and route it to multiple destinations would be very useful. Has anyone tried any of the possible solutions above for SNMP traps (or Netflow, general UDP, etc) load balancing? Or can anyone think of any other alternatives to solve this?

    Read the article

  • Building a Mac/PC Network in a Dorm with Network Restrictions

    - by user70340
    I have been a Windows XP user for the last few years, but I recently bought a 15'' MacBook Pro for research purposes. I would like to set up a no-hassle Mac/PC Network at home so that I can access the internet on both computers and hardware between computers (i.e. a harddrive, or a mouse/keyboard with Synergy). Unfortunately, I live in a dorm with silly network restrictions so a solution is not straightforward. In particular: The dorm has a wired and wireless network, both which provide an internet connection. The wired network provides way faster internet (download speeds of 15 MB/s vs. 2 MB/s on wireless), so I would like to somehow exploit this, at least on my PC for Bittorrent :) Multiple devices can connect to the wireless network, but cannot "see" each other on the network (so software like Synergy would not work). Only 1 MAC address can connect to the wired network at a time. Ideally I would just connect a wireless router to the wired network and then have both the Mac and the PC on that, but the 1 MAC address restriction will not allow the both computer to access the internet simultaneously. I cannot think of a way to bypass this restriction (though I'm not network savvy), so I am planning to create a private no-internet network to allow the devices to see each other and share hardware. Here are some thoughts. I would appreciate any feedback at all! If I build a private wireless network: (first choice) I will use a wireless router that is not connected to the internet. My PC and Mac will be connected to each other wirelessly. I can then connect the PC to the internet via a wired network, but then the Mac will not have internet access as its wireless card is already in use. In this case, could I stream internet access from the PC to the Mac via the wireless network? Or could I buy a USB wireless card for the Mac so that it can connect to both my private network and the dorm network? If I build a private wired network: (second choice) Then both the PC and the Mac will connect to the internet wirelessly, which means I cannot take advantage of the faster download speeds.

    Read the article

  • Problems when trying to connect to a router wirelessly

    - by Ruud Lenders
    The situation - At my girlfriend's parents' place there are six Windows 7 devices that are wired or wireless connected to a router: 3 dekstops and 3 laptops. There are also several smartphones using the router. The router is secured with WPA2 (AES). The problem - We never had any problems with the router for over a year. But recently - about 3 weeks ago - my girlfriend's laptop (HP) and my laptop (ASUS) started to develop problems while trying to connect to the router. The router has stopped showing up from the network list. Sometimes it comes back and shows up, but then it keeps saying something along the lines of "Could not connect", and not long after that it dissapears again. The range of the router is not the problem here, because we experience the same when we sit next to the router. Sometimes, if we are lucky, and waited a long time (10-15 minutes) without using the laptop for anything, the laptop will eventually succesful connect to the router. The attempts - Of course, the Window 7 troubleshooter. We tried troubleshooting the connection problems and the wireless network adapter, but no luck. We also reset the router enough times to know that's not helping either. Here's the full list of things we tried, but did not help: Running the Windows 7 troubleshooter Resetting the router (more than once) Setting the router settings to factory defaults Disconnecting all other devices except one laptop Applying a system restore Trying static/dynamic IP/DNS - Dynamic is better, right? Enabling/disabling IPv6 - Should I keep IPv6 disabled? Running the command: netsh wlan stop hostednetwork Running the command: netsh wlan set hostednetwork mode=disallow Updating/reïnstalling wireless adapter drivers The tests - To help finding the core of the problem, we tested the following: Plugging an ethernet cable in the router and in our laptops - worked fine Connecting someone else's laptop to the router (wireless) - worked fine Connecting our laptops to someone else's router - worked fine The router - This information might be relevant: Router model: Sitecom 300N Wireless Router Router hardware: version 01 The DCHP Server's IPs range from 192.168.0.100 to 192.168.0.200. Router settings: Wireless channel: 12 Channel bandwidth: 20/40 MHz Extension channel: 8 Preamble type: Long 802.11g protection: Disabled UPnP: Enabled The laptops - If you are wondering about our laptops: My laptop model: ASUS Pro64JQ Girlfriend's laptop: HP Pavillion G6 OS: Both Windows 7 Professional x64 - with Service Pack 1 My wireless adapter: Atheros AR9285 AdHoc 11n: Enabled The question - Does anyone have experienced the same problems as I do? Or does someone know how to solve this? Are there more tricks I can try, or settings I should change? Note - Our laptops are not slow or old. My laptop is 1.5 years old, and the other laptop is just 5 months old. I know how to keep laptops clean and I'm pretty sure both laptops are not bloated with useless software.

    Read the article

  • Hyper-V causes boot loop/failure on a non-Gigabyte Win8 Pro system

    - by Nick
    Hardware: Intel i7 2600K (not overclocked, SLAT compatible, virt. features enabled in bios) Asus Maximus IV Extreme-Z (Z68) 16Gb RAM 256Gb SSD Other non-trivial working parts Adding Hyper-V is causing a boot loop resulting in an attempt at automatic repair by Windows 8 after the second or third loop: I'm trying to get the Windows Phone 8 SDK installed and I've narrowed down my troubles to the Hyper-V feature in Win8. This is required to run the WP8 emulator and there are no install options to omit this feature. My first attempt completely borked the OS as I did not have a recent restore point or system image, so I did a completely clean install and made plenty of backups/restore points. I skipped the SDK install and went straight for the windows feature add-on for Hyper-V. This confirmed that Hyper-V is the issue as the same behavior resulted. I cannot find any hint in the Event Logs. Cancelling automatic recovery causes the same behavior to repeat. I don't have any other VM products installed. My only recourse is to use a restore point, try something else, install it again, and see what happens. No luck so far. I'm on my 10th attempt here. Any help would be much appreciated. EDIT: I found a collection of tips here.. http://social.msdn.microsoft.com/Forums/en-US/wptools/thread/b06cc9f2-aa5e-4cb3-9df1-0c273e1dfd68 So i've been attempting various bios settings to resolve this issue with no luck. I've tried setting 'CPUID Limit' to disabled. This seems to work partly as Win8 boots but no USB devices work at all. I also attempted disabling the usb 3.0 controller as the msdn topic lists an issue with USB controllers on Gigabyte boards. This also doesn't work. The USB devices light up but no input is received by the OS. All of my other bios CPU settings are in line with the info in the post. I'm totally stumped. Bios screenshots: http://i.imgur.com/yKN5u.png http://i.imgur.com/Y9wI4.png http://i.imgur.com/F6EuO.png

    Read the article

  • Arp tries on various *nix based systems.

    - by salparadise
    Does anyone know what determines the amount of arp tries a router will make? I have different behaviors with two devices, if I try to traceroute to a non-existent host on a subnet that belongs to an interface on the router, a Linux box will try to arp 3 times and then return a host un-reacheable icmp message. Junos will continuosly try to arp and not return anything. Is there a sysctl value that determines this or anything at all.

    Read the article

  • How to setup a Wi-Fi 2-computer network with Internet sharing?

    - by Narek
    I have the following devices: Desktop Computer (Windows XP Professional) Laptop Computer (Windows Vista Home Premium) A USB modem that I want to connect to my Desktop computer (so my Desktop has Internet) And a Wi-Fi router (D-Link, model: DIR-300) that I want to use in order to create a connection between mentioned two computers to be able to share files and what is the most important thing to make my laptop to have access to the Internet. What steps I should do to have this system?

    Read the article

  • Is Steam for Mac effectively running as superuser?

    - by godDLL
    When you download the client it does not weigh too much, and seems to do very little. Inside the app bundle there is a script that—upon inspecting the environment and deciding you're not running Linux—launches the client, which downloads the full support environment and resources. For this to happen (all of this is saved inside the bundle, the app bundle gets updated in this process) Steam wants Universal Access for Assistive Devices, and your password. Cacheable resources, preferences (like keyboard shortcuts), support files (like game hardware requirement lookup tables) live inside the bundle, not in ~/Library/{Application Support|Preferences|Cache}; games' data get dumped into ~/Documents/Steam Content. I'd describe myself as a bit OCD (which really says a lot), and I wouldn't care that much still. I'd go comb this hairy mess and find out where stuff is, when and if I need to, even if it's in an unfamiliar place; that does not actually tick me off. Well, a little bit. What makes me concerned is the way Steam needs both Access for Assistive Devices, and my password to run. The former gives it the ability to talk very intimately with running apps and the underlying system; while the latter (admin account) could very well give it and it's publishers unrestricted access to all my software, hardware and data. With publishers like Rockstar using scene NOCD cracks to publish their games on Steam, I'm not so sure I'm OK with this. I'd like more games made available for the MacOS X and all the pretty machines that run it, but this arrangement does not seem very Mac-like to me. It looks like Valve is going around system security measures and best practices, foregoing sandboxing, code signing, relatively sane structured organization; all the things that would appeal to someone who's no fun at parties at all, and will die alone, in his long dead mother's basement… wait. Right. Anyway. Can we get some input on Steam for Mac security at the end-user machine, from someone who understands how Accessibility API works, whether games distributed on Steam can read and write outside the user homefolder, collect data from other running apps, or similar?

    Read the article

  • Is my Cisco switch port bad?

    - by ewwhite
    I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

    Read the article

  • Cisco ASA SSL VPN options?

    - by JonH
    Disclaimer: I am not a network admin so I may be wrong here but I thought asking here would help. I'm a developer mainly on the .net framework as well as helping get a mobile intranet app working. Because this app is only allowed to be used on our network I can easily run this app on our wireless network connection within our building. All is fine and dandy but we'd also like to be able to run this mobile app at say a customer plant using VPN software. I thought surely this could be easy as we exclusively use Samsung s4 phones so I thought I'd download Cisco's Samsung any connect software to allow us to VPN...its right on the play store. Sure enough it doesn't work. I mention it to our network admin who says not possible since we have old technology that doesn't support SSL. He mentions we'd have to upgrade all of our hardware, the firewall, etc. to get this to work. We really need VPN on our phones not only for this app but other internal apps, etc. He did mention the following: We can’t upgrade the software on our ASA, because we don’t have enough memory for the new version.  (the asa is very old).  We can’t add more memory, so we would have to get a new firewall, which I have been told I cannot do. In addition he also mentioned: The Samsung AnyConnect client uses SSL to connect.  With the current (old) version of software that our firewall is running, the SSL connections are unreliable.  We need different hardware in order to upgrade our firewall, which we are unable to attain at this time.  This is the same reason that Windows 8 clients are not able to connect. I am curious hence me asking. vpns seem to be fairly simple to setup. What other options do I have aside from making this a public site or web service that consumes this data over the internet as this is a complete no no. What can we do to make this work without that much effort or cost.

    Read the article

< Previous Page | 205 206 207 208 209 210 211 212 213 214 215 216  | Next Page >