Search Results

Search found 30511 results on 1221 pages for 'linux networking'.

Page 212/1221 | < Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >

• WIFI looses connection with AR9285 - have to disconnect / connect to regain internet?

  - by CodyLoco

  I have a G73JW laptop using Ubuntu 12.04. It has an Atheros AR9285 card. While wifi seems to work fine most of the time, about every hour or two it will loose the connection to the internet. The connection will appear to be connected still to the wireless router, but internet access is gone. Disconnecting and reconnecting to the access point solves the problem, as does disabling and reenabling the adapter via the hardware keyboard shortcut. How might this be solved so the connection is stable and doesn't drop? EDIT: It looks like the network dropping isn't related to DNS as it fails either way: codyloco@CodyLoco-Ubuntu:~$ dig askubuntu.com @8.8.8.8 ; <<>> DiG 9.8.1-P1 <<>> askubuntu.com @8.8.8.8 ;; global options: +cmd ;; connection timed out; no servers could be reached codyloco@CodyLoco-Ubuntu:~$ dig askubuntu.com ; <<>> DiG 9.8.1-P1 <<>> askubuntu.com ;; global options: +cmd ;; connection timed out; no servers could be reached Again cycling (disabling / enabling) the adapter corrects the issue.

  Read the article

• Ubuntu 12.04 wireless does not detect networks

  - by dudeitsdevin90

  I installed Ubuntu on a partition of my MacBook Pro. Wireless connections work fine when I switch to OSX, but the wireless networks are not even detected when I boot Ubuntu. I installed Wicd as a new network manager, but I'm still having the same problem. Ubuntu works on a wired connection though. I have searched the web for a solution... similar questions have been asked but I have not been able to find a way to fix this problem. Any help would be greatly appreciated.

  Read the article

• Wired connection not working

  - by YokoBlac

  I am using a Acer Aspire One. Here is the Ubuntu Wiki Page about my computer. I have a working wireless connection however when I plug a cat5 (Ethernet) cable in the lights flicker on the computer, but then nothing happens. Output of iconfig: eth0 Link encap:Ethernet HWaddr 00:1e:68:96:1a:6b inet6 addr: fe80::21e:68ff:fe96:1a6b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:43 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2622 (2.6 KB) TX bytes:936 (936.0 B) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) wlan0 Link encap:Ethernet HWaddr 00:22:68:92:7f:36 inet addr:192.168.1.6 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::222:68ff:fe92:7f36/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5702 errors:0 dropped:0 overruns:0 frame:0 TX packets:5284 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4117327 (4.1 MB) TX bytes:936709 (936.7 KB) Any understanding of this output is greatly appreciated.

  Read the article

• ssh login information

  - by bob

  As the admin of my machine, I want users to be able to log into my computer with ssh, but I'm looking for a graphical way to be notified that a user is connected at the moment. If multiple users are connected, I want a list of connected users, their location, name, etc. This could be in the form of a forceCommand and 'alert' command when someone logs in, plus a icon saying how many people are connected right now in the notification bar, with the option to click on it to have more information about these users. Is there such a tool available in ubuntu, and if not, how to do it (I'm guessing it's not that difficult and could be done with under ten bash command lines) ?

  Read the article

• Ubuntu 12.04 - PPTP VPN is the only Internet Access

  - by user212553

  I know this has been covered. I've read dozens of posts but still have questions. I have a work server whose traffic should never leave my house without encryption. The VPN is PPTP. Currently I have a cron job that checks the status of the ppp0 adapter each minute. If the connection drops, which it does fairly often, it shuts key components down. It's fairly easy to restart PPTP with "nmcli con up id 'myVPNServer'" but there's no assurance it will reconnect and I need a better way to stop traffic (other than killing apps) when ppp0 is down. The two options I've seen discussed are the firewall (UFW, Firestarter, IPTables) or the route tables. I could be easily swayed to consider the firewall option but I focused on the route tables since no new function needs to be started. My questions involve the way the route tables change and then specifics on rules. When I start the PPTP VPN the route tables change. That suggests that if the VPN drops, the table will change back, defeating my stated intent of preventing external traffic. How can I make "sticky" changes to the route table that will persist even if the VPN connection drops? Perhaps the check boxes "Ignore automatically obtained routes" or "Use this connection only for resources on it's network" (which are part of the VPN configuration options)? It would seem that, if I can force the active VPN route table to stay in effect, even when the VPN drops, that this will effectively kill any external traffic should the VPN drop. This will give me the latitude to run a routine to restart the VPN from the command line (assuming the route table rules don't prevent me re-establishing the connection). My route table, with the VPN active is (ip route list): Any comments on what 10.10.1.1 is? $ ip route list default dev ppp0 proto static 10.10.1.1 dev ppp0 proto kernel scope link src 10.10.1.11 VPN_Server_IP_Address via 192.168.1.1 dev eth0 proto static VPN_Server_IP_Address via 192.168.1.1 dev eth0 src 192.168.1.60 169.254.0.0/16 dev eth0 scope link metric 1000 192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.60 metric 1

  Read the article

• Is it possible to setup a DHCP server only for local virtual machines?

  - by thiesdiggity

  I have a quick question. I have a bunch of virtual machines (VMWare Workstation) running on an Ubuntu server and have found that VMWare NAT (DHCP) service is unreliable and slow. I have to use NAT instead of bridging because the server is in a data-center that does not have DHCP and I don't have enough static IP's for all the VMs. Is it possible to setup the host (Ubuntu) to be a DHCP server but only for the local virtual machines? The server has 2 network interfaces, so I'd set eth0 to be a static IP, which connects to the outside world, and eth1 to listen for DHCP. Now, I am thinking if I don't want DHCP to broadcast I would just not connect a cable to eth1 and setup the VM's to use bridging on eth1. That way DHCP would not broadcast through my network but be listening on that interface. Would that setup work?

  Read the article

• Track ping, download and upload daily

  - by euDennis

  I'm with some problems with my internet with oscillations in connection, causing some sites to get "Not Found" page sometimes. This isn't all the time, just some random times daily. My question is. There is any tool to monitor these basic information (ping, upload and download) daily to make an report and check the oscillations? Because, if someone from internet provider come at my house, probably it won't see the oscillations. Thanks, bye

  Read the article

• Is it illegal to forward copyrighted content? [closed]

  - by Mike

  Ok, this may be a strange question, but let's start: If I illegally download a movie (for example...) from a HTTP Web Server, there are many routers between me and the Web Server which are forwarding the data to my PC. As I understand, the owners of the routers are not legally responsible for the data they forward (please correct if I'm wrong). What if I would install a client of a peer-to-peer network on my PC and this client (peer) would forward copyrighted content received from peers to other peers? Hope someone understand what I mean ;-) Any answer or comment would be highly appreciated. Mike Update 1: I'm asking this question because I want to develop a p2p-application and try to figure out how to prevent illegal content sharing/distribution (if forwarding content is really illegal...) Update 2: What if the data forwarded by my peer is encrypted, so I'm technically not able to read and check it?

  Read the article

• All traffic is passed through OpenVPN although not requested

  - by BFH

  I have a bash script on a Ubuntu box which searches for the fastest openvpn server, connects, and binds one program to the tun0 interface. Unfortunately, all traffic is being passed through the VPN. Does anybody know what's going on? The relevant line follows: openvpn --daemon --config $cfile --auth-user-pass ipvanish.pass --status openvpn-status.log There don't seem to be any entries in iptables when I enter sudo iptables --list. The config files look like this: client dev tun proto tcp remote nyc-a04.ipvanish.com 443 resolv-retry infinite nobind persist-key persist-tun persist-remote-ip ca ca.ipvanish.com.crt tls-remote nyc-a04.ipvanish.com auth-user-pass comp-lzo verb 3 auth SHA256 cipher AES-256-CBC keysize 256 tls-cipher DHE-RSA-AES256-SHA:DHE-DSS-AES256-SHA:AES256-SHA

  Read the article

• Using two ethernet connections (Internet enabled) simultaneously

  - by vedarthk

  I have searched and read over the Internet and also on askubuntu. i am using Ubuntu 11.04 and my question or the thing that I want to achieve is efficient use of both the connections and thus increasing my browsing and downloading speed. I want my system to decide which packet should be routed over which interface. I want to know if this is possible. For example, Is it possible to route alternate packets over the two interfaces ? Please let me know any Internet resource or If I would have to insert any code into the network drivers etc. ?

  Read the article

• Network connection on an Acer Aspire 5253?

  - by fuquam

  Brand new to Ubuntu and PCs for that matter. I've been a Mac user all my life but wanted to try Ubuntu on the cheap, so I bought an Acer Laptop 5253-BZ893 and i got Ubuntu 10.10 installed with no problem. The only problem i have is, that i get no network connection options, wired or wireless. I just get No Network Devices Available. The computer came with Windows 7 installed and i am able to connect to my wireless network fine using Windows, so i know the computer works. Also i've been searching forums and google for hours trying to figure out why I can't get a network connection in Ubuntu but so far no luck. Any suggestions? Thanks in advance.

  Read the article

• Choosing the correct network protocol for my type of game (its Wc3 Warlock style)

  - by Moritz

  I need to code a little game for a school project. The type of the game is like the Warcraft 3 map "Warlock", if anyone doesnt know it, here is a short description: up to ten players spawn into an arena filled with lava, the goal of each player is to push the other players into the lava with spells (basically variations of missiles, aoe nukes, moba spells etc) http://www.youtube.com/watch?v=c3PoO-gcJik&feature=related we need to provide multiplayer-support over the internet, for that reason I am looking for the best network protocol for this type of game (udp, tcp, lock step, client-server...) what the requirements are: - same/stable simulation on all clients - up to ten players - up to ~100 missiles on the field - very low latency since its reaction based (i dont know the method wc3 used, but it was playable with the old servers) what would be nice (if even possible, since the traffic might be too big): - support for soft bodies over the network (with bullet physics), but this is no real requirement I read several articles about the lock step method used for RTS games, this seems to be great, but does it fit for real-time action games too (ping-related)? If anyone has run into the same problems/questions like me, I would be very happy about any help

  Read the article

• Having trouble installing Bradcom STA driver

  - by user192881

  I just installed Ubuntu and love it so much, its so fast now. But I have a problem connecting to the internet. I checked and saw I have to install the driver Broadcom STA wireless driver but every time I do try to install it it says: Sorry, installation of this driver failed. Please have a look at the log files for details: /var/log/jockey.log I went to the terminal and copy and pasted the log file name. and when I did it, it said I have no permission to access this file. I checked on the forums that I have to be on a wired connection. So I plugged my laptop into my router and I got internet then tried to install the driver again. And it was loading then when it got to the end the same message popped up. Also I have one of those little USB router things you plug into the computer and it gives you internet I have been using that but its to slow. So I want to use the one in my computer but cant. Also I tried the command: sudo modprobe wl and when i type that command in it says: FATAL: Module wl not found Also I'm using Ubuntu 12.04

  Read the article

• How can an application (like Firefox) be forced to use a certain network interface?

  - by Lekensteyn

  I've two interfaces: eth0 and wlan0 on a notebook. Possible use cases: eth0 grants me Internet access, and wlan0 is currently connected to a router which does not have Internet-connectivity. For development purposes, I need to connect to the wlan0 by default, but use eth0 for surfing eth0 and wlan0 are both connected to the Internet. For a torrent application, eth0 should be used for speed, but for portability of the notebook, SSH should have a connection over wlan0 eth0 is a wire connection, wlan0 is a wireless one. Sensible data should be transferred over eth0, but other traffic can go over wlan0 as well. Is there a way to force applications (like nc.traditional or firefox) to use a certain network interface? A wrapper like example-wrapper eth0 program is fine too if such program exist. It would be nice if it could configured within Firefox (in runtime). I'd like to avoid IPTables solutions if possible.

  Read the article

• Who Provides Internet Service for My Internet Service Provider?

  - by Jason Fitzpatrick

  You pay your Internet Service Provider (ISP) for internet access, and they turn on the sweet, sweet, fire hose of data for you. But who provides the flow for your ISP? Read on to learn the ins and outs of global data delivery. Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-drive grouping of Q&A web sites. HTG Explains: How Windows Uses The Task Scheduler for System Tasks HTG Explains: Why Do Hard Drives Show the Wrong Capacity in Windows? Java is Insecure and Awful, It’s Time to Disable It, and Here’s How

  Read the article

• Report: Ubuntu Claims 12 Million Users as Lucid Linux Desktop Nears

  Canonical and Ubuntu revamp the Linux desktop with social networking, mobile sync, downloadable DRM-free music and a new look.

  Read the article

• problems establishing ssh connection

  - by Superbyte

  since two days I am facing a really weird problem. I have receantly installed ubuntu server 14.04 LTS on a workstation. It has a fix IP address, which I can successfully ping from other computers in the network. But when I try to establish a ssh connection from a windows computer via putty I get some strange errors, which I cannot fix. The Problem is that putty takes a really long time trying to establish a connection. After about 10 seconds I get the following error: Network error: Software caused connection abort But when I click the Restart Session option a several times after putty shows the error message, I can login in. But now comes the other problem. When the login appears on the putty console I type in the user, but it really takes a long time until I can type in the password to login. This is what I already tried: sshd: ALL in etc/hosts.allow commented line session optional pam_motd.so in etc/pam.d/login and etc/pam.d/sshd configured the firewall with: sudo iptables -A INPUT -p tcp --dport ssh -j ACCEPT checked if ssh server is listening on port 22 UseDNS no in etc/ssh/sshd_config I hope someone can help me, because this problem is really annoying. Thanks in regard

  Read the article

• MAC filtering after DHCP

  - by user1655161

  How to manage filtering by MAC in Ubuntu? Scenario: Ubuntu DHCP is configured and working (network 192.168.1.0) a) Laptop 1 is set in configuration on Ubuntu as static IP Laptop 1 is configured for automatic IP and when is connected to server everything works. I'm taking laptop 2 which is configured as static IP 192.168.1.10 and his configuration is not set in Ubuntu dhcpd.conf After laptop 2 is connected internet working. It is possible to do MAC filtering which disallow to connect PCs with address IP set as static but MAC address is not configured in Ubuntu (something like: intruder in network)?

  Read the article

• why does our network printer not show up on some of our macs, but does show up on others? [on hold]

  - by peter

  We lost power in our building and now cannot get our HP laser jet 5200 to be recognized by half of our computers. We are all Macs, some running OS 10.7.5 can see the printer, others running 10.7.5 cannot, and those running 10.8.5 and 10.9 cannot. We've re-booted the router, turned off and on printer and macs—no go. The printer displays an IP address (dynamically assigned) but we can't access it. Tried to see it using CUPS—same story, can see it on some systems, not on others. Any thoughts?

  Read the article

• Forti VPN Client not connecting to a server under Ubuntu 14.04

  - by deonis

  I've just updated to a new version of Ubuntu (14.04 86x64) and I got a very strange problem with Forti VPN Client. It seems running smoothly, but when I try to connect via GUI or terminal it hangs at the connection stage. here is what I see in terminal: STATUS::Setting up the tunnel STATUS::Connecting... #and this takes forever I know that it's not the problem with the server, the client works no problem on windows. Thank in advance ...

  Read the article

• eth0 not working on startup

  - by user4106

  Hi to all, This might sound strange but, working with my Lubuntu 10.04 i've experienced troubles when connecting to my eth0 newtwork. After some googling, i've found out that by writting in the CLI the following command: mii-tool eth0 -F 10baseT-FD and activating the eth0 in the toolbar (by clicking "activate eth0") everything works just fine. Well, up to now, i did not have any problem, because every time i turned on the computer i had to do this, but it was very little effort.But now, i would like to use the machine as a file server, accesing it by ssh, without monitor or keyboard. So, i won't be able to make this actions, and can't do this at startup because mii-tool needs root permissions. So, the question is: Do you know what does that command do, and how can id make that change permanent? Or do you know any other solution for my problem? I hope i was clear! If not, tell me and i'll try to be as clearer as possible. Thanks in advance!

  Read the article

• lshw not showing network

  - by triunenature

  Output: {User}@{Computer}:~$ sudo lshw -class network {User}@{Computer}:~$ Another Test: {User}@{Computer}:~$ lspci 00:00.0 RAM memory: NVIDIA Corporation MCP61 Memory Controller (rev a1) 00:01.0 ISA bridge: NVIDIA Corporation MCP61 LPC Bridge (rev a2) 00:01.1 SMBus: NVIDIA Corporation MCP61 SMBus (rev a2) 00:01.2 RAM memory: NVIDIA Corporation MCP61 Memory Controller (rev a2) 00:02.0 USB controller: NVIDIA Corporation MCP61 USB 1.1 Controller (rev a3) 00:02.1 USB controller: NVIDIA Corporation MCP61 USB 2.0 Controller (rev a3) 00:04.0 PCI bridge: NVIDIA Corporation MCP61 PCI bridge (rev a1) 00:05.0 Audio device: NVIDIA Corporation MCP61 High Definition Audio (rev a2) 00:06.0 IDE interface: NVIDIA Corporation MCP61 IDE (rev a2) 00:07.0 Bridge: NVIDIA Corporation MCP61 Ethernet (rev a2) <<---- Network Card???? 00:08.0 IDE interface: NVIDIA Corporation MCP61 SATA Controller (rev a2) 00:08.1 IDE interface: NVIDIA Corporation MCP61 SATA Controller (rev a2) 00:09.0 PCI bridge: NVIDIA Corporation MCP61 PCI Express bridge (rev a2) 00:0b.0 PCI bridge: NVIDIA Corporation MCP61 PCI Express bridge (rev a2) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:05.0 FireWire (IEEE 1394): LSI Corporation FW322/323 (rev 70) 02:00.0 VGA compatible controller: NVIDIA Corporation G96 [GeForce 9500 GT] (rev a1) If you look at 00:07.0 I believe that is the network card. However lshw doesnt show it. I mainly need information on network speed 10MBpS/100MBsP/1000MBpS Though knowing why my system isn't working would be nice.

  Read the article

• how to congest a link using iperf

  - by navaz

  I have setup like below. Switch1-------------------- Switch2 | | | | | | | | | | | | PC1 PC2 PC3 PC4 I have a video traffic is flowing between PC1 and PC4. I have configured PC2 as iperf server. ( iperf -s ) and PC3 as client . (iperf -c 10.10.10.2 -P 20 -t 10000) where 10.10.10.2 is PC2 IP. now I am seeing most of the traffic in a link (switch1---switch2) is iperf. (TCP). I have observed from the logs that 1 out of 300 packet is UDP. Still I am not seeing any difference in the quality of video streaming in PC4. It looks similar compared to the case with no iperf. I am checking QOS, I have tried many options with iperf, couldnt succeed. I want to diminish the quality of video streaming in PC4. Could you please tell me what options can be used along with iperf to do it. Bandwidth between Switch1---switch2 is 1Gbits/sec. Thanks in advance

  Read the article

• Wired connection not being recognized

  - by maxifick

  I'm on Ubuntu Maverick (10.10). I've read a few threads regarding wired connection problems, but haven't found a solution yet. The problem appears after I connect to a wireless network. When I disconnect wireless and plug in an internet cable, the wired connection is not recognized at all. Even the socket appears dead (there are no diodes flashing). The only solution so far seems to be restarting the computer. Network Manager then tries to connect to a Wi-Fi, but the wired connection is listed and working. I've tried sudo restart network-manager, but that doesn't solve anything. After a while, available wireless networks start appearing, but the wired still doesn't. Any ideas? Thanks in advance. Edit: Here is the dmesg output after switching off Wi-Fi and then plugging the internet cable. [18200.623543] Restarting tasks ... done. [18200.648422] video LNXVIDEO:00: Restoring backlight state [18200.707580] sky2 0000:02:00.0: eth0: phy I/O error [18200.707715] sky2 0000:02:00.0: eth0: phy I/O error [18200.707819] sky2 0000:02:00.0: eth0: phy I/O error [18200.707922] sky2 0000:02:00.0: eth0: phy I/O error [18200.708025] sky2 0000:02:00.0: eth0: phy I/O error [18200.708127] sky2 0000:02:00.0: eth0: phy I/O error [18200.708229] sky2 0000:02:00.0: eth0: phy I/O error [18200.708332] sky2 0000:02:00.0: eth0: phy I/O error [18200.708824] sky2 0000:02:00.0: eth0: enabling interface [18200.709587] ADDRCONF(NETDEV_UP): eth0: link is not ready [18202.662422] EXT4-fs (sda9): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 [18203.324061] EXT4-fs (sda9): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 [18211.193137] eth1: no IPv6 routers present [18212.844649] usb 5-1: new low speed USB device using ohci_hcd and address 5 [18213.017235] input: USB Optical Mouse as /devices/pci0000:00/0000:00:13.0/usb5/5-1/5-1:1.0/input/input16 [18213.017499] generic-usb 0003:0461:4D17.0004: input,hidraw0: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:13.0-1/input0 After system restart, dmesg says this: [ 19.802126] sky2 0000:02:00.0: eth0: enabling interface [ 19.802394] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 20.812533] device eth0 entered promiscuous mode [ 21.495547] sky2 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control rx [ 21.495677] sky2 0000:02:00.0: eth0: Link is up at 100 Mbps, full duplex, flow control rx [ 21.496574] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

  Read the article

• after upgrade from 10.04 to 12.04 cannot boot with linux 3.2.0-24-generic-pae

  - by Ricardo

  After upgrade from 10.04 to 12.04, I cannot boot with linux 3.2.0-24-generic-pae: process gets frozen in a xubuntu initialization screen (I had qimo installed). If I try the recovery mode (with the same Linux version), booting freezes after this message: Begin: Mounting root file system. If in grub menu I choose Previous Linux versions, I can boot using Linux 2.6.32-41-generic-pae. But once logged in, some things don't seem to work (apt-get update fails, update manager fails, HID menu does not provide suggestions...) (to be honest, I have no idea whether this is part of the bigger issue) Reading in Ask Ubuntu through apparently similar problems, I decided to follow some advices: got boot-repair and run it. The problem remains & I got this report. I also run as root in terminal $ sudo update-initramfs -u and this is what I got: update-initramfs: Generating /boot/initrd.img-3.2.0-24-generic-pae cryptsetup: WARNING: failed to detect canonical device of /dev/sda1 cryptsetup: WARNING: could not determine root device from /etc/fstab /tmp/mkinitramfs_EIDlHy/scripts/classmate-bottom/45xconfig: 9: .: Can't open /scripts/casper-functions What else? My pc is Intel® Core™ i7 CPU 870 @ 2.93GHz × 8, graphs is GeForce 8400 GS/PCIe/SSE2, memory is 7,8 GiB. I have two questions: Is this a bug in the newest kernel I should report? Is there anything I can do appart from a fresh install?

  Read the article

< Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >