Search Results

Search found 17984 results on 720 pages for 'log shipping'.

Page 215/720 | < Previous Page | 211 212 213 214 215 216 217 218 219 220 221 222  | Next Page >

• Xubuntu 12.04 : Random boot to black screen

  - by Thibaud Ruelle

  My xubuntu 12.04 has worked flawlessly since install in September. However, lately I randomly have the following boot issue : The computer boots to grub, and after choosing xubuntu either boots normally or boots to a black screen. Here are some observations I have made : The black screen seems to happen randomly. The black screen does not seem to happen in safe mode (- nomodeset in grub). The black screen does not allow me to ctrl + alt + F1-6 into a terminal. The black screen allows me to use SysRq keys (Alt + SysRq + K does not work though). The black screen often happens on first boot in several hours and the computer usually boots normally after a RSEINUB. When the computer boots I get "SP5100 TCO timer: mmio address 0xfec000f0 already in use" at startup and "Could not write bytes: broken pipe" at shutdown. However research on these errors did not yield answers to my particular issue. Comparing Xorg.0.log (successful boot) and Xorg.0.log.old (black screen), and reading the answers to similar problem, it seems that I might have a X driver issue. However the system worked flawlessly since lately. Additional info on my system : ACER AO722 C62kk Operating system : 3.2.0-31-generic ubuntu Edit : I made a fresh install of Xubuntu 12.04 x64, the issue is still there ... (I have a separate /home so config. files were not erased). Edit 2 : I followed troubleshooting blank screen, so my new observations are without quiet and splash in grub : When the system boots normally, the screen goes black after grub then lights up and displays text information then goes to login screen. (After that the desktop starting time vary substantially, which is new and may be a separate issue ?). When the boot fails, after grub the screen goes black, lights up, goes black, lights up again and most times goes black again. At this point it responds to Alt+SysReq K by lighting up but no more, and has to be rebooted through Alt+SysReq+ RSEINUB. Thank you for your time and attention in advance ! Thibaud Ruelle

  Read the article

• Bad certificate error with RabbitMQ using SSL

  - by David Tinker

  I am trying to get RabbitMQ working with SSL on a couple of Gentoo servers. I get the following error in /var/log/rabbitmq/rabbit@...log when I try to connect to the management console using https: SSL: certify: ssl_connection.erl:1641:Fatal error: bad certificate I followed the instructions here: http://www.rabbitmq.com/ssl.html The annoying thing is that I have 2 cloned servers and it is working on one and not the other. As far as I can tell the machines are configured identically. I wrote a script to generate the certs etc. and have run it on both. I am not using client certificates. Anyone know how I can figure out whats wrong with my certificate(s)? I am using Erlang 15.2, RabbitMQ 2.7.9, OpenSSL 0.9.8k.

  Read the article

• Management Reporter Installation – Lessons Learned Part II - Dynamics GP

  - by Ryan McBee

  After feeling pretty good about my deployment skills of Management Reporter for Dynamics GP a few weeks ago, I ran into two additional lessons learned that I wanted to share. First, on another new deployment, I got the error shown below which says “An error occurred while creating the database.  View the installation log for additional information.”  This problem initially pointed me to KB 2406948 which did not provide resolution. After several hours of troubleshooting, I found there is an issue if the defaults database locations in SQL Server are set to the root of a drive. You will want to set the default to something like the following to get it installed; C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA.  My default database locations for the data and log files were indeed sitting on the H:\ and I:\ drives. To change this property in your SQL Server Instance you need to open SQL Server Management Studio, right click on the server, and choose properties and then database settings. When I initially got the error, I briefly considered creating the ManagementReporter database by hand, but experience tells me that would have created more headaches down the road. The second problem I ran into with this particular deployment of Management Reporter happened when I started the FRx conversion utility.  The errors reads “The ‘Microsoft.ACE.OLEDB.12.0’ provider is not registered on the local machine. I had a suspicion that this error was related to the fact FRx uses outdated technology and I happened to be on a new install of Server 2008 R2.  A knowledge base search quickly pointed me to KB 2102486. The resolution for this Management Reporter issue was to install the Microsoft Access Database Engine Redistributable, by following the site below. http://www.microsoft.com/downloads/details.aspx?familyid=C06B8369-60DD-4B64-A44B-84B371EDE16D&displaylang=en

  Read the article

• How do you author HDR content?

  - by Nathan Reed

  How do you make it easy for your artists to author content for an HDR renderer? What kinds of tools should you provide, and what workflows need to change, in going from LDR to HDR? Note that I'm not asking about the technical aspects of implementing an HDR renderer, but about best practices for creating materials and lighting in HDR. I've googled around a bit, but there doesn't seem to be much about this topic on the web. Can anyone point me to some good resources on this, or share their own experiences? Some specific points: Lighting - how can lighting artists pick HDR light colors? Do they have a standard LDR color picker and then a multiplier? Is the multiplier in gamma or linear space? Maybe instead of a multiplier it's a log-luminance? Or a physical brightness level, like the number of lumens? How will they know what multiplier/luminance/brightness is "correct" for a given light? Materials - how can texture artists make emissive color maps, such as neon signs, TV screens, skyboxes, etc? Can you paint one as a regular LDR (8-bit-per-channel) image and apply a multiplier (or log-luminance, etc.)? Are there cases where it's necessary to actually paint HDR images? If so, how do you go about this in Photoshop (or other software)?

  Read the article

• How can I move along an angled collision at a constant speed?

  - by Raven Dreamer

  I have, for all intents and purposes, a Triangle class that objects in my scene can collide with (In actuality, the right side of a parallelogram). My collision detection and resolution code works fine for the purposes of preventing a gameobject from entering into the space of the Triangle, instead directing the movement along the edge. The trouble is, the maximum speed along the x and y axis is not equivalent in my game, and moving along the Y axis (up or down) should take twice as long as an equivalent distance along the X axis (left or right). Unfortunately, these speeds apply to the collision resolution too, and movement along the blue path above progresses twice as fast. What can I do in my collision resolution to make sure that the speedlimit for Y axis movement is obeyed in the latter case? Collision Resolution for this case below (vecInput and velocity are the position and velocity vectors of the game object): // y = mx+c lowY = 2*vecInput.x + parag.rightYIntercept ; ... else { // y = mx+c // vecInput.y = 2(x) + RightYIntercept // (vecInput.y - RightYIntercept) / 2 = x; //if velocity.Y (positive) greater than velocity.X (negative) //pushing from bottom, so push right. if(velocity.y > -1*velocity.x) { vecInput = new Vector2((vecInput.y - parag.rightYIntercept)/2, vecInput.y); Debug.Log("adjusted rightwards"); } else { vecInput = new Vector2( vecInput.x, lowY); Debug.Log("adjusted downwards"); } }

  Read the article

• Filemaker 10 Advanced sending email via script & SMTP

  - by Sean

  We are using a windows server box to run the databases but we have found via the headers that the emails are send from the local workstation. We have moved to a new email system and have set up a local linux server to securely send email out of our network to devices that do not support new protocols and encryption. But once we set up the script in filemaker 10 advanced (the local machine os x) we set it to the ip of our local box with no authentication but it does not send out an email. It creates a connection we see in the logs on the linux box but nothing more, additionally you can start a telnet connection with no issues. We have also made sure that there are no additional issue that we can see in our firewall policies. Any ideas where we should start? Does Filemaker 10 advanced log errors anywhere because I could not find any log files.

  Read the article

• apache 2.4 php-fpm proxypassmatch for pretty urls

  - by tubaguy50035

  I have a URL like http://newsymfony.dev/app_dev.php/_profiler/5080653d965eb. I would like to send this script to PHP-FPM. I currently have this as my vhost: VirtualHost *:80> ServerName newsymfony.dev DocumentRoot /home/COMPANY/nwalke/www/newsymfony.dev/web/ ErrorLog /var/log/apache2/error_log LogLevel info CustomLog /var/log/apache2/access_log combined <Directory /home/COMPANY/nwalke/www/newsymfony.dev/web/> AllowOverride All Require all granted DirectoryIndex app.php </Directory> ProxyPassMatch ^/(.*\.php)$ fcgi://127.0.0.1:9003/home/COMPANY/nwalke/www/newsymfony.dev/web/$1 </VirtualHost> If I browse to app_dev.php it works just fine. But if I do app_dev.php/_profiler/5080653d965eb I get a 404 and the request never gets sent to FPM. How can I alter my ProxyPassMatch to pass anything with .php in the URL? I'm trying to do this with Symfony, but I'm pretty sure it applies to everything.

  Read the article

• Why might apache2 use 100% of CPU at startup?

  - by QuantumMechanic

  This is apache 2.2.14 on SLES9. Out of nowhere (i.e. it had been working fine for ages) I am seeing apache2 suddenly start using 100% of the CPU at startup, and never completing startup. Nothing is getting written to /var/log/error_log (when it did back when things were OK). ps only shows the main httpd process and not any of the spawned threads. When things were OK, it would show the spawned threads. So it appears httpd is going into some sort of infinite loop right at startup and isn't even completing startup. It's not an issue of being overloaded by connections -- this happens even when nothing is trying to contact it. The config files haven't changed (or at least they haven't changed in a way that changed their last-modified time). I've tried added -e debug -E /var/log/apache2/startup_info to the command line, but nothing is put in the file. Any ideas what could be happening?

  Read the article

• The Mystery of the Vanishing Disk Space

  - by Oddthinking

  My disk space is dwindling by about 2GB a day! I only have a few more days before I run out of space. $ df -h Filesystem Size Used Avail Use% Mounted on /dev/sda4 143G 126G 11G 93% / udev 491M 4.0K 491M 1% /dev tmpfs 200M 696K 199M 1% /run none 5.0M 0 5.0M 0% /run/lock none 499M 144K 499M 1% /run/shm /dev/sda2 1.9G 580M 1.2G 33% /tmp /dev/sda1 92M 29M 58M 33% /boot I have been searching for the biggest directories/log files, deleting and compressing. But I am still losing the war. Finally, I realised I have a big misunderstanding: julian@server1:~$ sudo du -h / | tail -n 1 16G / All of my files in / only add up to 16 GB. That leaves 110 GB unaccounted for! Clearly I have a misunderstanding: I thought the '/dev/sda4' line represented all the files visible from '/'. What should I be reading to understand where the other storage has gone? More details: I have an Ubuntu 11.10 server, that was set-up by data-center staff. It is running my own code (which is fairly prolific with log files, but otherwise doesn't store much stuff on the drive) duplicity for backups (which tends to store a lot of signature files) various other standard services, like Apache, nagios, etc. They are very lightly used. It has been up for about 4 months without a reboot. I lied about the du output (simplified it for effect). It also complained about not being able to access GVFS and the du processes's own resources. I believe they are irrelevant: . du: cannot access `/home/julian/.gvfs': Permission denied du: cannot access `/proc/10841/task/10841/fd/4': No such file or directory du: cannot access `/proc/10841/task/10841/fdinfo/4': No such file or directory du: cannot access `/proc/10841/fd/4': No such file or directory du: cannot access `/proc/10841/fdinfo/4': No such file or directory

  Read the article

• subdomain/virtualhost problem on unix + apache

  - by Aaron

  Hello, I'm having a strangely difficult time setting up a subdomain (x.example.com). The main site works fine, but I get 404 errors attempting to hit x.example.com no matter how I set up the VirtualHost config. NameVirtualHost *:80 <VirtualHost *:80> ServerName www.example.com DocumentRoot /var/www/example.com/htdocs ServerAlias example.com </VirtualHost> <VirtualHost *:80> ServerName x.example.com ErrorLog /var/logs/x-error-log CustomLog /var/logs/x-access-log common DocumentRoot /var/www/x/htdocs </VirtualHost> As far as I can tell, this is a vanilla set up. Any suggestions would be appreciated.

  Read the article

• Bootstrapping in CloudFormation with Autoscale

  - by PapelPincel

  My CloudFormation template creates an autoscale group and bootstrap it with utility script /opt/aws/bin/cfn-init. When I remove the bootstrap part out of my template the, autoscale get created without any problem, but I add it the CloudFormation Stack fails and add line in /var/log/cloud-init.log : Error: AutoScalingGroupName does not specify any metadata The line above appens right after the following command : /opt/aws/bin/cfn-init --verbose --configsets orderedConfig --region us-east-1 --stack AS15 --resource AutoScalingGroupName --access-key XXXXXXXXXXXXX --secret-key XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX Digging a little bit deeper, in cfn-init I added the following lines the point where it exit: from pprint import pprint pprint(vars(detail)) and I get the following trace when running the previous cfn-init command : {'_description': None, '_lastUpdated': datetime.datetime(2012, 7, 12, 14, 52, 42), '_logicalResourceId': u'AutoScalingGroupName', '_metadata': None, '_physicalResourceId': u'AS15-AutoScalingGroupName-HNPOXXXXXXXX', '_resourceStatus': u'CREATE_COMPLETE', '_resourceStatusReason': None, '_resourceType': u'AWS::AutoScaling::AutoScalingGroup', '_stackId': u'arn:aws:cloudformation:us-east-1:XXXXXXXXXXXXX:stack/AS15/XXXXXXXX-cc30-11e1-XXXXXX-XXXXXXXXXX', '_stackName': u'AS15'} As you can see, the metadata field is empty and that's the reason why it fails to create the stack. Is there any known side effects for cfn-init when used with autoscale ?

  Read the article

• Multiple CAS servers with Microsoft Exchange and selective authorization

  - by John Wilcox

  I have a Microsoft Exchange 2010 organization within one Microsoft Windows domain and I have users accessing it through OWA. For simplicity lets say I currently have one CAS server (CAS 1) which is accessible only through a VPN connection. Lets call the users connecting to the first CAS group a. For some users though, I need to install another CAS server (CAS 2) so that they can connect without using a VPN connection. Lets call those users group b. What I need to achieve is that group a can only log in to CAS 1 and group b can only log in to CAS 2. Now I know that one can disable/enable OWA per user but in my case that is not enough because OWA must be enabled for both groups.

  Read the article

• How can I make PDFs appear life-size when displayed at 100%?

  - by ændrük

  When I open a letter size PDF and then zoom to 100%, the page physically displayed on my monitor is smaller than a real letter size sheet of paper. How can I make "100%" on the computer screen correspond with "100%" in real life? Details This message suggests that I should be investigating the system-wide DPI settings for my monitor. xdpyinfo reports: dimensions: 1024x768 pixels (271x203 millimeters) resolution: 96x96 dots per inch My monitor has a native display resolution of 1024x768 pixels and a diagonal display size of 12.07 inches. PX CALC returns the following information: DPI: 106.05 Dot Pitch: 0.2395mm Size: 9.66" × 7.24" (24.53cm × 18.39cm) What I've tried so far Running xrandr --dpi 106.05 successfully caused my PDF to appear actual size at 100%, but this effect was lost after rebooting. To make the setting persistent I tried creating the following /etc/X11/xorg.conf: Section "Monitor" Identifier "ThinkPad X60 LCD" DisplaySize 245 183 EndSection Section "Screen" Identifier "Screen0" Monitor "ThinkPad X60 LCD" EndSection After re-logging in, /var/log/Xorg.0.log contained [ 1167.824] (**) intel(0): Display dimensions: (245, 183) mm [ 1167.824] (**) intel(0): DPI set to (106, 106) but xdpyinfo still reported dimensions: 1024x768 pixels (271x203 millimeters) resolution: 96x96 dots per inch and "100%" still appeared too small. Link to XRANDR wiki Link to making XRANDR changes persistant

  Read the article

• How do I fix my installation of ATI Catalyst Video Drivers in 12.04 LTS?

  - by Boris

  My graphic card is a Mobility Radeon HD 4200 Series. I tried these 2 answers from What is the correct way to install ATI Catalyst Video Drivers in 12.04 LTS? But unfortunately, it does not work for me: When running the amd script, I get this error message: $ sudo sh ./amd-driver-installer-12-4-x86.x86_64.run ... DKMS part of installation failed. Please refer to /usr/share/ati/fglrx-install.log for details When checking this log file, I get: Uninstalling any previously installed drivers. Creating symlink /var/lib/dkms/fglrx/8.961/source -> /usr/src/fglrx-8.961 DKMS: add completed. Kernel preparation unnecessary for this kernel. Skipping... Building module: cleaning build area.... cd /var/lib/dkms/fglrx/8.961/build; sh make.sh --nohints --uname_r=3.2.0-24-generic-pae --norootcheck......(bad exit status: 1) [Error] Kernel Module : Failed to build fglrx-8.961 with DKMS [Error] Kernel Module : Removing fglrx-8.961 from DKMS Deleting module version: 8.961 completely from the DKMS tree. Done. [Reboot] Kernel Module : update-initramfs When checking with fglrxinfo, I get: $ fglrxinfo X Error of failed request: BadRequest (invalid request code or no such operation) Major opcode of failed request: 138 (ATIFGLEXTENSION) Minor opcode of failed request: 66 () Serial number of failed request: 13 Current serial number in output stream: 13

  Read the article

• DSL connection not working in 10.04

  - by Mussnoon

  I use a wired PPPoE connection to connect to the Internet. What I need to do on Windows to connect to it is put in static IP address, gateway, subnet mask and DNS servers for my LAN card. Next I have to create a dialer for a PPPoE connection, put in my user name, the service name and the password, and "dial" this connection. And it works fine. On Ubuntu 10.04, however, I have tried setting things up in a similar fashion - put in all static addresses for the "automatic" wired connection, then put in user name, service name, password for a "DSL" connection. It worked for a while, then stopped. I have tried putting in all the details within the DSL configuration dialog, same thing happened - it worked for a while, then stopped. I have tried deleting the ethernet connection and only keeping the DSL one with all the numbers put in place, same thing happened - it worked for a while, then stopped. Each of the times, when it connected, it connected randomly, after trying a few times, and either stopped working within a few minutes, or after I had rebooted. I have deleted and remade the connection dozens of times - even with different names, but nothing seems to be working. I have also tried pppoeconf from the terminal, didn't work. I have checked /var/log/kern.log, but nothing changes in the file when I try to connect. I have also checked /sbin/route, but gedit can't even open it (says it can't figure the character encoding...). The "connection established" notification pops up from the top right corner, the same way as when the computer is actually connected to a network. Can anyone figure what's wrong and how it can be solved?

  Read the article

• Having trouble installing guest additions for a Xubuntu 13.10 guest OS in Virtualbox 4.2.10

  - by Duval Pearson III

  I am using Ubuntu 13.04 64-BIT as my host operating system running Virtual Box 4.2.10. I get this message when I tell virtualbox to install guest additions(CTRL+D),mounting the volume in the guest OS and run the VBoxLinuxAdditions.run file using root by: sudo ./VBoxLinuxAdditions.run It starts and then comes to these error messages: Verifying archive integrity... All good. Uncompressing VirtualBox 4.2.10 Guest Additions for Linux.......... VirtualBox Guest Additions installer Removing existing VirtualBox non-DKMS kernel modules ...done. Building the VirtualBox Guest Additions kernel modules The headers for the current running kernel were not found. If the following module compilation fails then this could be the reason. Building the main Guest Additions module ...done. Building the shared folder support module ...fail! (Look at /var/log/vboxadd-install.log to find out what went wrong) Doing non-kernel setup of the Guest Additions ...done. Installing the Window System drivers Warning: unknown version of the X Window System installed. Not installing X Window System drivers. Installing modules ...done. Installing graphics libraries and desktop services components ...done. allusers@allusers-VirtualBox:/media/allusers/VBOXADDITIONS_4.2.10_84104$ I followed everything from the official VirtualBox manual on installing guest additions for linux I used some other commands such as: sudo apt-get install build-essential linux-headers-$(uname -r) dkms and: sudo apt-get install virtualbox-guest-x11 I rebooted after executing those command and it still wont work. It still says the kernel modules are missing and the window is not seamless. Any idea what could be the problem?

  Read the article

• New technical product guide for Sun Ray clients

  - by Jaap

  In the Oracle online documentation system a new Sun Ray clients Technical Product guide has been published. The document provides detailed information about the similarities and differences between the three Sun Ray client hardware models: Sun Ray 3, Sun Ray 3 plus and Sun Ray 3i. From the description of the Technical Product guide I want to quote the following section: "......Since Sun Ray 3 Series Clients have no local operating system and require no local management, they eliminate the complexity, expenses, and security vulnerabilities associated with other thin client and PC solutions. ......" This is always one of the great advantages of Sun Ray clients compared to other thin clients (which are actually low-fat PCs where you have to manage thin client OS images). The guide lists the features and technical specifications of the Sun Ray Client such as number of ports, chassis, graphics, network interfaces, power supply, operating conditions, MTBF, reliability, and other standards. The guide also contains a separate chapter about environmental data. As you may know, the Sun Ray 3 Series clients are designed specifically to be sensitive to a spectrum of environmental concerns and standards, from materials to manufacturing processes to shipping, operation, and end of life. The Sun Ray 3 Series clients complies to environmental standards and certifications such as Energy Star 5.0, EPEAT, WEEE and RoHS (see the Oracle policy for RoHS and REACH).

  Read the article

• Getting error when using Oracle imp command to import dmp file

  - by blizz

  I am importing a dmp file using the following command: imp user/pass file=file.dmp log=logfile.log full=y ignore=y destroy=y I get the following errors: . . importing table "MESSAGE_BOARD" IMP-00058: ORACLE error 22993 encountered ORA-22993: specified input amount is greater than actual source amount IMP-00028: partial import of previous table rolled back: 219638 rows rolled back . . importing table "MESSAGE_BOARD_ARCHIVES" IMP-00058: ORACLE error 22993 encountered ORA-22993: specified input amount is greater than actual source amount IMP-00028: partial import of previous table rolled back: 2477960 rows rolled back I have tried increasing the tablespace size and adding a second datafile to no avail. I'm a total newb at Oracle so any help will be appreciated. Googled this for hours and still can't come up with a solution. Thanks!

  Read the article

• Hanging page loads every n loads

  - by Christian

  Hi Guys I recently moved my site to a new server (Apache 2, PHP5, MySQL5). The site is an Invision based forum. Every few posts / topics it just hangs. The data has been written because if you stop and reload, the post / thread is there. I thought it was a write issue initially, but nope. So, the data is written but the page load never completes. It doesn't leave the page where the data has been input. Whats the best way to trouble shoot this issue? The only thing I have done recently is reduce my MySQL timeouts, but I can't see that being an issue as the values are still big enough and there are no mentions of timeouts in the MySQL log. (For the record there is nothing in PHP's error log either) Thanks in advance!

  Read the article

• unexpected EOF and end of document

  - by WASasquatch

  I have been fiddling with this code for a few days. Mind you I am a beginner. I just want to get my script to be able to download a remote file, and scan MineCraft plugins. I got the scan plugins to work, but I'm having two other issues. One, I can't get the mc_addplugin to work correctly, and I get a Unexpected EOF and unexpected end of document when running any other command besides mc_scanplugins or mc_start bash: -c: line 0: unexpected EOF while looking for matching `"' bash: -c: line 1: syntax error: unexpected end of file Help would be so much appreciated! Thanks in advance. #!/bin/bash # /etc/init.d/craftbukkit # version 0.9.1 2012-07-06 (YYYY-MM-DD) ### BEGIN INIT INFO # Provides: craftbukkit # Required-Start: $local_fs $remote_fs # Required-Stop: $local_fs $remote_fs # Should-Start: $network # Should-Stop: $network # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: Starts craftbukkit server # Description: Starts and controls the craftbukkit server ### END INIT INFO # SETTINGS SERVICE='craftbukkit-1.2.5-R1.0.jar' OPTIONS='nogui' USERNAME='smith' # LIST ALL THE WORLDS IN YOUR CRAFTBUKKIT SERVER FOLDER WORLDS[1]='world' WORLDS[2]='world_nether' WORLDS[3]='world_the_end' WORLDS[4]='flat_world' MCPATH='/var/www/servers/Foundation' PLUGINSPATH='/var/www/servers/Foundation/plugins' TEMPPLUGINS='/var/www/servers/Foundationplugins/temp_plugins' BACKUPPATH='/var/www/servers/Foundation/backup' CPU_COUNT=2 INVOCATION="java -Xmx2024M -Xms2024M -XX:+UseConcMarkSweepGC -XX:+CMSIncrementalPacing -XX:ParallelGCThreads=$CPU_COUNT -XX:+AggressiveOpts -jar $SERVICE $OPTIONS" ME=`whoami` as_user() { if [ $ME == $USERNAME ] ; then bash -c "$1" else su - $USERNAME -c "$1" fi } mc_start() { if pgrep -u $USERNAME -f $SERVICE > /dev/null then echo "$SERVICE is already running!" else echo "Starting $SERVICE..." cd $MCPATH as_user "cd $MCPATH && screen -dmS craftbukkit $INVOCATION" sleep 7 if pgrep -u $USERNAME -f $SERVICE > /dev/null then echo "$SERVICE is now running." else echo "Error! Could not start $SERVICE!" fi fi } mc_saveoff() { if pgrep -u $USERNAME -f $SERVICE > /dev/null then echo "$SERVICE is running... suspending saves" as_user "screen -p 0 -S craftbukkit -X eval 'stuff \"say The server is preforming a backup. Server going to read-only mode. Do not build...\"\015'" as_user "screen -p 0 -S craftbukkit -X eval 'stuff \"save-off\"\015'" as_user "screen -p 0 -S craftbukkit -X eval 'stuff \"save-all\"\015'" sync sleep 10 else echo "$SERVICE is not running. Not suspending saves." fi } mc_save() { if pgrep -u $USERNAME -f $SERVICE > /dev/null then echo "$SERVICE is running... Saving worlds..." as_user "screen -p 0 -S craftbukkit -X eval 'stuff \"save-all\"\015'" sync sleep 10 echo "Save complete!" else echo "$SERVICE is not running. Cannot save!" fi } mc_saveon() { if pgrep -u $USERNAME -f $SERVICE > /dev/null then echo "$SERVICE is running... re-enabling saves" as_user "screen -p 0 -S craftbukkit -X eval 'stuff \"save-on\"\015'" as_user "screen -p 0 -S craftbukkit -X eval 'stuff \"say Server backup has completed. Server going to read-write mode. You can now continue building...\"\015'" else echo "$SERVICE is not running. Not resuming saves." fi } mc_stop() { if pgrep -u $USERNAME -f $SERVICE > /dev/null then echo "Stopping $SERVICE" as_user "screen -p 0 -S craftbukkit -X eval 'stuff \"say $SERVERNAME is shutting down in 30 seconds! Please stop what you are doing. Check back later, we'll be back!\"\015'" as_user "screen -p 0 -S craftbukkit -X eval 'stuff \"save-all\"\015'" sleep 30 as_user "screen -p 0 -S craftbukkit -X eval 'stuff \"stop\"\015'" sleep 7 else echo "$SERVICE was not running." fi if pgrep -u $USERNAME -f $SERVICE > /dev/null then echo "Error! $SERVICE could not be stopped." else echo "$SERVICE is stopped." fi } mc_update() { if pgrep -u $USERNAME -f $SERVICE > /dev/null then echo "$SERVICE is running! Will not start update." else MC_SERVER_URL=http://dl.bukkit.org/latest-rb/craftbukkit.jar as_user "cd $MCPATH && wget -q -O $MCPATH/craftbukkit_server.jar.update $MC_SERVER_URL" if [ -f $MCPATH/craftbukkit_server.jar.update ] then if `diff $MCPATH/$SERVICE $MCPATH/craftbukkit_server.jar.update >/dev/null` then echo "You are already running the latest version of $SERVICE. Update anyway? [Y/n]" select yn in "Yes" "No"; do case $yn in Yes ) as_user "mv $MCPATH/$SERVICE $MCPATH/${SERVICE}_old.jar" as_user "mv $MCPATH/craftbukkit_server.jar.update $MCPATH/$SERVICE" echo "$SERVICE updated successfully!"; break;; No ) echo "The update was not installed! Removing temporary files and exiting..." as_user "rm $MCPATH/craftbukkit_server.jar.update" exit;; esac done else as_user "mv $MCPATH/$SERVICE $MCPATH/${SERVICE}_old.jar" as_user "mv $MCPATH/craftbukkit_server.jar.update $MCPATH/$SERVICE" echo "$SERVICE updated successfully!" fi else echo "$SERVICE update could not be downloaded." fi fi } mc_addplugin() { if pgrep -u $USERNAME -f $SERVICE > /dev/null then echo "$SERVICE is running! Please stop the service before adding a plugin." else echo "Paste the URL to the .JAR Plugin..." read JARURL JARNAME=$(basename "$JARURL") if [ -d "$TEMPPLUGINS" ] then as_user "cd $PLUGINSPATH && wget -r -A.jar $JARURL -o temp_plugins/$JARNAME" else as_user "cd $PLUGINSPATH && mkdir $TEMPPLUGINS && wget -r -A.jar $JARURL -o temp_plugins/$JARNAME" fi if [ -f "$TMPDIR/$JARNAME" ] then if [ -f "$PLUGINSPATH/$JARNAME" ] then if `diff $PLUGINSPATH/$JARNAME $TMPDIR/$JARNAME >/dev/null` then echo "You are already running the latest version of $JARNAME." else NOW=`date "+%Y-%m-%d_%Hh%M"` echo "Are you sure you want to overwrite this plugin? [Y/n]" echo "Note: Your old plugin will be moved to the "$TEMPPLUGINS" folder with todays date." select yn in "Yes" "No"; do case $yn in Yes ) as_user "mv $PLUGINSPATH/$JARNAME $TEMPPLUGINS/${JARNAME}_${NOW} && mv $TEMPPLUGINS/$JARNAME $PLUGINSPATH/$JARNAME"; break;; No ) echo "The plugin has not been installed! Removing temporary plugin and exiting..." as_user "rm $TEMPPLUGINS/$JARNAME"; exit;; esac done echo "Would you like to start the $SERVICE now? [Y/n]" select yn in "Yes" "No"; do case $yn in Yes ) mc_start; break;; No ) "$SERVICE not running! To start the service run: /etc/init.d/craftbukkit start"; exit;; esac done fi else echo "Are you sure you want to add this new plugin? [Y/n]" select yn in "Yes" "No"; do case $yn in Yes ) as_user "mv $PLUGINSPATH/$JARNAME $TEMPPLUGINS/${JARNAME}_${NOW} && mv $TEMPPLUGINS/$JARNAME $PLUGINSPATH/$JARNAME"; break;; No ) echo "The plugin has not been installed! Removing temporary plugin and exiting..." as_user "rm $TEMPPLUGINS/$JARNAME"; exit;; esac done echo "Would you like to start the $SERVICE now? [Y/n]?" select yn in "Yes" "No"; do case $yn in Yes ) mc_start; break;; No ) "$SERVICE not running! To start the service run: /etc/init.d/craftbukkit start"; exit;; esac done fi else echo "Failed to download the plugin from the URL you specified!" exit; fi fi } mc_scanplugins() { if [ "$(ls -A $PLUGINSPATH)" ] then shopt -s nullglob PLUGINS=($PLUGINSPATH/*.jar) i=1 for f in "${PLUGINS[@]}" do echo "${i}: $f" PLUGIN[$i]=$f i=$(( $i + 1 )) done echo "Enter the ID of a plugin you want removed, or any other key to cancel." read INPUT if [ ! -z "${INPUT##*[!0-9]*}" ] then if [ -f "${PLUGIN[INPUT]}" ] then echo "Removing plugin..." JAR=$(basename ${PLUGIN[INPUT]}) JARNAME=${JAR%.jar} as_user "rm -f ${PLUGIN[INPUT]}" sleep 2 as_user "cd $PLUGINSPATH && rm -rf ./${JARNAME}" if [ -f "${PLUGINSPATH}/${JARNAME}" ] then echo "Plugin folder could not be removed..." fi echo "Plugin removed." else echo "${PLUGIN[INPUT]}" echo "Invalid plugin! Does not exist! Canceling..." exit; fi else echo "Canceling..." exit; fi else echo "You have no plugins installed." exit; fi } mc_backup() { mc_saveoff for i in "${WORLDS[@]}"; do NOW=`date "+%Y-%m-%d_%Hh%M"` BACKUP_FILE="$BACKUPPATH/${i}_${NOW}.tar" echo "Backing up world: $i..." #as_user "cd $MCPATH && cp -r $i $BACKUPPATH/${i}_`date "+%Y.%m.%d_%H.%M""` as_user "tar -C \"$MCPATH\" -cf \"$BACKUP_FILE\" $i" done echo "Backing up $SERVICE" as_user "tar -C \"$MCPATH\" -rf \"$BACKUP_FILE\" $SERVICE" #as_user "cp \"$MCPATH/$SERVICE\" \"$BACKUPPATH/craftbukkit_server_${NOW}.jar\"" mc_saveon echo "Compressing backup..." as_user "tar -cvzf $BACKUPPATH/server_backup_${NOW}.tar.gz $MCPATH" echo "Backup has completed successfully." } mc_command() { command="$1"; if pgrep -u $USERNAME -f $SERVICE > /dev/null then pre_log_len=`wc -l "$MCPATH/server.log" | awk '{print $1}'` echo "$SERVICE is running... executing command" as_user "screen -p 0 -S craftbukkit -X eval 'stuff \"$command\"\015'" sleep .1 # assumes that the command will run and print to the log file in less than .1 seconds # print output tail -n $[`wc -l "$MCPATH/server.log" | awk '{print $1}'`-$pre_log_len] "$MCPATH/server.log" fi } #Start-Stop here case "$1" in start) mc_start ;; stop) mc_stop ;; restart) mc_stop mc_start ;; save) mc_save ;; update) mc_stop mc_backup mc_update mc_start ;; scanplugins) mc_scanplugins ;; addplugin) mc_addplugin ;; backup) mc_backup ;; status) if pgrep -u $USERNAME -f $SERVICE > /dev/null then echo "$SERVICE is running." else echo "$SERVICE is not running." fi ;; command) if [ $# -gt 1 ]; then shift mc_command "$*" else echo "Must specify server command (try 'help'?)" fi ;; *) echo "Usage: $0 {start|stop|update|backup|status|restart|command \"server command\"}" exit 1 ;; esac exit 0

  Read the article

• Website requests not reaching IIS?

  - by pete the pagan-gerbil

  To start off with a confession, I am not a server admin - just a developer tasked with getting to the root of a problem. Please be gentle! I have an intranet ASP.NET website running in IIS on a virtual machine. The website is not accessed very often (the last IIS log file was modified nearly six months ago). Both the IP address and Host header value are now failing to return the website, and the IIS log still doesn't show any more recent activity. The virtual machine was moved to a different physical location a few months ago, and the IP address for it has changed. Could this be what has broken access to the site? What else should I be checking to solve this? I don't have totally unrestricted access to the building's network settings, structures, etc. I would be grateful for any advice, even if I can't use it myself it'll improve my knowledge of what's going on behind the scenes!

  Read the article

• mediatomb fails with "respawning too fast, stopped"

  - by felix

  When I try to start mediatomb it fails. I see this in dmesg [...] [916349.374331] init: mediatomb main process ended, respawning [916349.394462] init: mediatomb main process (880) terminated with status 1 [916349.394512] init: mediatomb main process ended, respawning [916349.414598] init: mediatomb main process (882) terminated with status 1 [916349.414647] init: mediatomb respawning too fast, stopped My current /etc/init/mediatomb.conf looks like this. description "MediaTomb UPnP media server" author "Daniel van Vugt <vanvugt in launchpad>" start on (local-filesystems and net-device-up IFACE!=lo) stop on runlevel [!2345] respawn env CONFIGXML=/etc/mediatomb/config.xml env LOGFILE=/var/log/mediatomb.log env DEFAULT=/etc/default/mediatomb script [ -r $DEFAULT ] && . $DEFAULT [ ! $USER ] && USER=root [ ! $GROUP ] && GROUP=$USER if [ -n "$INTERFACE" ]; then INTERFACE_ARG="-e $INTERFACE" $ROUTE_ADD $INTERFACE fi exec mediatomb \ -c $CONFIGXML \ -u $USER \ -g $GROUP \ -l $LOGFILE \ $INTERFACE_ARG \ $OPTIONS end script post-stop script [ -r $DEFAULT ] && . $DEFAULT if [ -n "$INTERFACE" ]; then $ROUTE_DEL $INTERFACE fi end script

  Read the article

• Unable to install mysql in ubuntu

  - by Anand

  I purged my existing mysql-server from ubuntu and re-installed the same. This was due there was an upgrade from my ubuntu and I was unable to start my sql-server. After cleaned up and taking backup of my data , I re-insalled mysql. During installaion I received following message popup. Unable to set password for the MySQL "root" user An error occurred while setting the password for the MySQL administrative user. This may have happened because the account already has a password, or because of a communication problem with the MySQL server. You should check the account's password after the package installation. Please read the /usr/share/doc/mysql-server-5.5/README.Debian file for more information. ¦ ¦ After the installation was failed, following error were received. 121109 20:36:18 InnoDB: Initializing buffer pool, size = 128.0M 121109 20:36:18 InnoDB: Completed initialization of buffer pool 121109 20:36:18 InnoDB: highest supported file format is Barracuda. 121109 20:36:18 InnoDB: Waiting for the background threads to start 121109 20:36:19 InnoDB: 1.1.8 started; log sequence number 2395841 ERROR: 130 Incorrect file format 'user' 121109 20:36:19 [ERROR] Aborting 121109 20:36:19 InnoDB: Starting shutdown... 121109 20:36:20 InnoDB: Shutdown completed; log sequence number 2395841 121109 20:36:20 [Note] /usr/sbin/mysqld: Shutdown complete start: Job failed to start invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.5 (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of mysql-server: mysql-server depends on mysql-server-5.5; however: Package mysql-server-5.5 is not configured yet. dpkg: error processing mysql-server (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: mysql-server-5.5 mysql-server E: Sub-process /usr/bin/dpkg returned an error code (1)

  Read the article

• Finding a message in an archive in Kerio MailServer 6

  - by Karl Cassar

  I need to locate some emails from the archive. Kerio is set to archive emails on a daily basis, keeping the last 2 months. From the mail log, I found entries like: [09/Oct/2012 18:02:20] Recv: Queue-ID: 5074589c-00004ddb, Service: SMTP, From: <info@XXXXXXXXXXXX>, To: <Suzette@xxxxxxxxxxx>, Size: 699, Sender-Host: mail.XXXXXXXXXXX, User: automailer@XXXXXXXXXXXXXXX I need to locate this specific email. The archive folder has a lot of ZIP files like: 2012-Oct-06 2012-Oct-07 2012-Oct-08 2012-Oct-09 ... I assumed this would be in the 2012-Oct-09 zip file. I extracted it, and the zip file contains a lot of emails in the /#msgs/ folder, named: 0000000a.eml 0000000b.eml 0000000c.eml ... I did a search for the last part of the Queue-ID, 00004ddb, but it returned no results. I tried other random searches for other emails in the mail log, but I couldn't find a single one. Any idea how one goes about finding such an email in the archive?

  Read the article

• Gnome trash on cifs mount random behaviour

  - by BobPenguin

  Hello everyone, I'm seeing some weird behaviour in Ubuntu 10.04. I have a cifs mount that's mounted by fstab as follows: //192.168.1.1/share /media/storage cifs_netdev,username=guest,password="",uid=1000,guid=100,file_mode=0777,dir_mode=0777 0 0 I can mount the share using: sudo mount -a my user can then access it, create and delete files. The deleted files appear in the gnome trash applet. A folder /media/storage/.Trash-1000 is created automatically. When I log out, restart the machine and log in, the cifs share is mounted but the trash applet is empty. If I unmount the share with sudo umount /media/share then remount with sudo mount -a the trash applet displays the contents of the .trash-1000 folder! It gets stranger...sometimes after umount then mount -a the trash is STILL empty, but another round of umount then mount -a fixes it. It seems like the trash applet is "forgetting" to scan the /media/storage mount point and is not always finding the .trash-1000 folder at that mount point. Even when the trash applet is not displaying any trash from /media/storage/.trash-1000 I can still delete things from the /media/storage and they're moved to the .trash-1000 folder. So I conclude there's a bug in the trash applet...anyone know how to fix it?

  Read the article

< Previous Page | 211 212 213 214 215 216 217 218 219 220 221 222  | Next Page >