Search Results

Search found 7325 results on 293 pages for 'windows7 32'.

Page 219/293 | < Previous Page | 215 216 217 218 219 220 221 222 223 224 225 226  | Next Page >

  • Almost All Logical Volumes Disappeared - Recovery?

    - by Alex
    We had a hard disc crash of one of two hard discs in a software raid with a LVM on top. The server is running Citrix xenserver. On the hard disk which is still intact, the volume group gets detected well, but only one LV is left. (some hashes replaced by "x") # lvdisplay --- Logical volume --- LV Name /dev/VG_XenStorage-x-x-x-x-408b91acdcae/MGT VG Name VG_XenStorage-x-x-x-x-408b91acdcae LV UUID x-x-x-x-x-x-vQmZ6C LV Write Access read/write LV Status available # open 0 LV Size 4.00 MiB Current LE 1 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 root@rescue ~ # vgdisplay --- Volume group --- VG Name VG_XenStorage-x-x-x-x-408b91acdcae System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 1 Act PV 1 VG Size 698.62 GiB PE Size 4.00 MiB Total PE 178848 Alloc PE / Size 1 / 4.00 MiB Free PE / Size 178847 / 698.62 GiB VG UUID x-x-x-x-x-x-53w0kL I could understand if a full physical volume is lost - but why only the logical volumes? Is there any explanation for this? Is there any way to recover the logical volumes? EDIT We are here in a rescue system. The problem is that the whole server does not boot (GRUB error 22) What we are trying to do is to access the root filesystem. But everything was in the LVM. We have only this: (parted) print Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 750GB 750GB primary boot, lvm And this 750GB LVM volume is exactly what we see on top.

    Read the article

  • Slow, choppy video playback with nVidia 8600GT

    - by user5351
    I have an nVidia 8600GT card (made by EVGA) on a machine with Windows Vista (AMD Athlon X2 processors) and four gigs of ram. It runs pretty good, but I have had some slow/choppy/stuterring video playback issues whenever watching flash videos on Youtube or other sites. The problem is there with both Firefox and IE flash videos, but is maybe worse with Firefox. I also tried Linux with nVidia's binary drivers and it was about the same. I downloaded EVGA precision which allows me to control stuff like the fan and clock speed. The card's temp (in both Vista and Linux) is usually at 66C when idle (not playing a game or watching anything). It goes up a little when watching a video (maybe 68-72C). Any ideas on how to fix this? UPDATE: The issues are both with full screen and embedded flash videos. I have Flash 10.0.32.18 (always make sure I use most recent for security), and the CPU is an AMD Athlon 64 X2 Dual Core Processor 4000+ at 2.11 GHZ. The current GPU driver installed is the most recent GeForce one from last July.

    Read the article

  • InstallShield or Windows installer corrupted

    - by Bobby S
    Just recently I've been unable to install any software on my Windows 7 machine. Anything that uses InstallShield or the Windows installer will just hang or give a weird error. I noticed there will be many duplicate isbew64.exe processes (like 25) that launch and then just sit there or else a lot of msiexec.exe *32 processes, depending on what I'm trying to install. One piece of software specifically is the Logitech Harmony software. It gives me an *is_string_not_defined* error, saying c:\program files (x86)\:\ the filename, directory name, or volume label syntax is incorrect. The other thing I was trying to install was Battlefield: Bad Company 2, and that just hangs as well, and then just leaves all the Windows installer processes running in the background after I quit the install process. Very odd. I've checked well and googled these issues, it doesn't appear to be any sort of malware issue. I feel like it's related to some kind of corrupted installer application. I've rebooted, deleted the InstallShield folder in program files/common files as some places online suggested but to no avail. I have no idea what to do, any ideas?

    Read the article

  • Separated virtual networks with same subnet range with 2 interface

    - by Coolpet
    I'm having some problems with routing with the following: I have a server with 2 interfaces. It has 1-1 alias contains the same subnet. the 2 interface is connected to 2 switch, which are separated from each other. Infrastructure: Eth0 192.168.16.2/20 Eth0:eth0 192.168.1.222/20 Eth1 192.168.32.3/20 Eth1:eth1 192.168.1.223/20 I have a PC which has the IP address: 192.168.1.3/24 The problem is the next: If PC is on subnet 1, I can ping it. If PC is on subnet 2, I can't ping it. traceroute shows the route is across 192.168.1.222 ping -I 192.168.1.223 192.168.1.3 is not working on subnet 2. arp entries show the MAC address belonging to the correct interface (eth1 on subnet 2) How can I force the server to look on both interface same ranged subnet for specific IP? It searches only in the first subnet. The routing table has these 2 entries: 192.168.0.0/20 dev eth0 proto kernel scope link src 192.168.1.222 192.168.0.0/20 dev eth1 proto kernel scope link src 192.168.1.223

    Read the article

  • Seagate 3TB hard drive loses format information

    - by Victor Bugarin
    I have a Windows 7x64 Ultimate, 6 GB memory, 1 TB HD. 3TB Barracuda XT HDD. The HDD is installed on a StarTech 4 bays external enclosure I had troubles so I converted to a GPT, created 1 partition and formatted as NTFS. The hard drive I can write and read to and from the hard drive but it will become unreadable at some point while I am copying files or after I have copied files to it. I have copied large Bluray movies and diverse video files, I have also copied 32 GB of pictures, and I have copied about 86 thousand music files in different formats. At some point the partition becomes unreadable and I have to format the partition again (all files lost) and I have to start the whole process again. At some point I have been unable to copy large ISO (Bluray movies) file images. I have partitioned the HDD in 2 partitions P1 - 2TB, P2 - 1TB and I have lost every single file in either partition the same way. I reformat the HDD and it seems fine. I have run seatools to check the hard drive and it reports to be OK. What gives?

    Read the article

  • Nvidia RAID 1 Problem. Degraded drives...

    - by Vedat Kursun
    I had a RAID 1 on my system which has a Gigabyte GA 8N SLI motherboard with a Nvidia chipset.(Nvidia Raid IDE ROM BIOS 4.84) When the system was working probably there used to be an icon on the system try which showed my two RAID disks. Bu after my friend accidentally clicked on the "Remove drive safely" icon while trying to disconnect her USB, I noticed that the RAID system wasn't working. After a reboot there was suddenly a failure message during boot screen. When I enter the Nvidia RAID setup utility (F10) I can see that both drives are degraded and that won't change even if I get into them and press R for Rebuild. Other options are only Delete and Exit. When I boot to Windows (XP Pro 32 Bit) I can see both my disks with the same data on each of them but my RAID 1 is broken. It's a relief to see that at least my RAID 1 was active but it's annoying not being able to rebuild it. Is there a way where I can rebuild my RAID 1 without having to delete the array and build it again? Cause I don't want to backup 400 Gigs of data and then recopy it to my drives... (Disks 2 x Seagate ST3500418 AS SATA Drives)

    Read the article

  • Nvidia RAID 1 Problem. Degraded drives...

    - by Vedat Kursun
    I had a RAID 1 on my system which has a Gigabyte GA 8N SLI motherboard with a Nvidia chipset.(Nvidia Raid IDE ROM BIOS 4.84) When the system was working probably there used to be an icon on the system try which showed my two RAID disks. Bu after my friend accidentally clicked on the "Remove drive safely" icon while trying to disconnect her USB, I noticed that the RAID system wasn't working. After a reboot there was suddenly a failure message during boot screen. When I enter the Nvidia RAID setup utility (F10) I can see that both drives are degraded and that won't change even if I get into them and press R for Rebuild. Other options are only Delete and Exit. When I boot to Windows (XP Pro 32 Bit) I can see both my disks with the same data on each of them but my RAID 1 is broken. It's a relief to see that at least my RAID 1 was active but it's annoying not being able to rebuild it. Is there a way where I can rebuild my RAID 1 without having to delete the array and build it again? Cause I don't want to backup 400 Gigs of data and then recopy it to my drives... (Disks 2 x Seagate ST3500418 AS SATA Drives)

    Read the article

  • Windows 7 / TCP/IP network share guide - looking for to resolve failure to mount lacie network drive but works on XP,Linux,Mac.

    - by Rob
    Can anyone advise me of a really good, readable, Windows 7 TCP/IP network share guide, book, or reference. I want this because I cannot mount my Lacie 2big ethernet network drive in Windows 7 (32 bit home), but I can mount it in Windows XP Home 32bit, Ubuntu Linux 10.04 and Apple MacOS X. This drive is being mounted via the accompanying Lacie Ethernet Agent in XP (which I believe uses "Bonjour" protocol), on Mac and Linux it works without further need for software. Another Super User user has the same problem, but no answer: Trouble accessing network drives in Windows 7 I hope my take on the question shows a better willingness to investigate and do some digging - and therefore invite some suggestions to help with this. The drive is detected by Windows 7 (i.e. speech bubble "network drive found") but on trying to open an Explorer window, this remains blank with the Windows busy pointer. I'd prefer not to reinstall Windows 7 to see if that cures the problem, I'd rather understand what is happening/not happening, perhaps even compare differences with Windows XP. Suggestions, please for such guides or even the original problem itself. Update Edit Rewrote question more comprehensively here: Mhttp://superuser.com/questions/304209/looking-for-definitive-answer-to-accessing-a-network-share-via-windows-7-home-and

    Read the article

  • Screen randomly goes blue/black/white

    - by FubsyGamer
    Problem Randomly, while using my computer, the monitor goes dark grey/almost black, or it goes white with faint grey vertical lines, or it goes blue with black vertical lines. It's as if the computer powers off. People tell me I sign out of Skype, Spotify stops playing when it happens, etc. When I look at the tower, it doesn't seem like it's off at all. Nothing changes, fans are spinning, lights are on, etc. If you were only looking at the tower, you'd never know there was a problem The only way I can get it to come back up is to push and hold the power button and turn it off, then back on This never happens while I'm playing video games. I've done 5-6 hour sessions of League of Legends, and it doesn't do anything When I'm just browsing the web, reading email, checking Reddit, etc, it happens all the time. It can happen multiple times in a session, it usually takes only about 5 minutes from the time I start browsing to when the computer crashes This started happening after I moved to a new apartment (this has to be relevant somehow, it was not happening where I lived before) There is nothing in the crash logs or event logs System Specs i5 2500k CPU AMD Radeon 6800 GPU Gigabyte z68a-d3h-b3 motherboard WD VelociRaptor 1 TB HDD Screenshots Device manager About screen Things I have tried I was getting a WMI Error in my event logs, but I fixed it using Microsoft's fix, KB 2545227 I was using Windows 8. I wiped the HDD and downgraded to Windows 7 64 bit I took out the video card and used a can of air to totally clean out the video card, all fans, and the inside of the computer in general. I made sure all of the video card pins were fine, then reconnected it I tried to update my motherboard BIOS, but anything I downloaded from Gigabyte was only for 32 bit machines, not 64. I don't even know how to tell what my motherboard BIOS is at right now I am using a power strip, and anything else connected to it works just fine If I re-seat the monitor cable while this is happening, nothing changes Please, help me. I've been battling this for several weeks now, and it's so frustrating it makes me not even want to use the computer.

    Read the article

  • Windows 8 install from USB freezes

    - by Rafael Almeida
    I'm trying to install Windows 8 from an 8GB Kingston Data Traveler. I'm currently using the Windows 7 USB DVD Download Tool to put the iso into the flash drive. It copies the files, but in the end it says it 'had a problem with bootsect' and could not make the flash drive bootable. This seems to be because my current system is Windows 7 32bits, and the bootsect.exe in the ISO is a 64-bit executable. Then I downloaded the 32-bit bootsect.exe and made the drive bootable by running: bootsect /nt60 E: /mbr Then I restarted and managed to boot via the flash drive, but now everything is very slow. It takes about two minutes for the initial black screen with the Windows logo and the spinner go away, then it goes to a purple-ish blank screen that stays on for about five more minutes and then it finally shows a dialog asking for the installation, date/time and keyboard languages. I input then, click "Install Now" and it takes about three more minutes with a "Setup is starting" screen. After that, the PC apparently reboots, the CPU fan speeds up considerably, and there's no video and nothing more happens even after more than ten minutes. What is happening? I already tried using another USB port and even installing from a Samsung G3 Station 2TB external hard disk, but the same thing happens. The file transfer speed to the Kingston drive was about only 3 megabytes per second.

    Read the article

  • linux networking: how to redirect incoming connections from old server to new server?

    - by aliz
    hi I'm in the process of moving my old server to a new server, but i will keep the old server running for database replication and load balancing, etc. each server has a separate internet connection with a static ip, and they are connected through a local Ethernet connection. I've got Ubuntu 8.04 32-bit running on old server and Debian 6.0 64-bit on new one. shorewall firewall is installed on both servers. there are some outdoor devices which are periodically sending data to port 43597 for old server IP address. I can run multiple instances of the network service which is responsible for receiving data from devices on a server but on different ports. here's the question: how can I run the service on new server and have connections coming to old server redirected to it, and new devices can still connect to new server's IP address preferably on the same port and same service? until all devices get updated to send to new server. I've tried a shorewall DNAT rule, but seems like new server's default route should be changed to ethernet connection, which breaks other things. I also found about redir utility, but still haven't tried it. is there any best practice or simple solution for such a scenario, i'm not aware of? thanks in advance.

    Read the article

  • MysqlTunner and query_cache_size dilemma

    - by wbad
    On a busy mysql server MySQLTuner 1.2.0 always recommends to add query_cache_size no matter how I increase the value (I tried up to 512MB). On the other hand it warns that : Increasing the query_cache size over 128M may reduce performance Here are the last results: >> MySQLTuner 1.2.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.5.25-1~dotdeb.0-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in InnoDB tables: 6G (Tables: 195) [--] Data in PERFORMANCE_SCHEMA tables: 0B (Tables: 17) [!!] Total fragmented tables: 51 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 1d 19h 17m 8s (254M q [1K qps], 5M conn, TX: 139B, RX: 32B) [--] Reads / Writes: 89% / 11% [--] Total buffers: 24.2G global + 92.2M per thread (1200 max threads) [!!] Maximum possible memory usage: 132.2G (139% of installed RAM) [OK] Slow queries: 0% (2K/254M) [OK] Highest usage of available connections: 32% (391/1200) [OK] Key buffer size / total MyISAM indexes: 128.0M/92.0K [OK] Key buffer hit rate: 100.0% (8B cached / 0 reads) [OK] Query cache efficiency: 79.9% (181M cached / 226M selects) [!!] Query cache prunes per day: 1033203 [OK] Sorts requiring temporary tables: 0% (341 temp sorts / 4M sorts) [OK] Temporary tables created on disk: 14% (760K on disk / 5M total) [OK] Thread cache hit rate: 99% (676 created / 5M connections) [OK] Table cache hit rate: 22% (1K open / 8K opened) [OK] Open file limit used: 0% (49/13K) [OK] Table locks acquired immediately: 99% (64M immediate / 64M locks) [OK] InnoDB data size / buffer pool: 6.1G/19.5G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance Reduce your overall MySQL memory footprint for system stability Increasing the query_cache size over 128M may reduce performance Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 192M) [see warning above] The server has 76GB ram and dual E5-2650. The load is usually below 2. I appreciate your hints to interpret the recommendation and optimize the database configs.

    Read the article

  • Using multiple USB webcams in Linux

    - by rachelderp
    Running more than one USB webcam in Debian/Linux results in the the following error: libv4l2: error turning on stream: No space left on device VIDIOC_STREAMON: No space left on device What initially seemed to be a programming issue in OpenCV turned into a quest for a mysterious hardware/software problem after the same errors were produced by running cheese and xawtv. Apparently it's caused by webcams requesting all the available bandwidth on the USB host controller. With that in mind I decided to run wireshark and capinfos to see just how much bandwidth a single camera used. 4 megabits per second at 320x240 14 megabits per second at 640x480 32 megabits per second at 1920x1080 Interesting! That might explain why two cameras at 320x240 work but any higher resolution fails. It's as if my USB controller is only operating at USB 1 speeds, yet lsusb shows both webcams belonging to a device which supposedly supports 480 megabits per second. One solution proposed forcing the webcams to calculate their bandwidth usage instead of requesting their maximum by running the following commands: sudo rmmod uvcvideo sudo modprobe uvcvideo quirks=128 Unfortunately that made no difference, so I decided to try another solution. A post on StackOverflow suggested telling my webcams to use a lower FPS or compressed video format like MJPEG, but after running v4lctl list it doesn't appear either of my webcams support changing their video mode. And that's where I'm stuck. Why would two webcams operating well below the maximum speed of USB 2 would produce this error? ps: It's not a disk space issue, df displays no change when the webcams are started. pps: If it makes a difference, here's the output of lsusb

    Read the article

  • certificate SSH login does not work on 22 but other port

    - by Hugo
    On my Red Hat server, the sshd will not accept my correct certificate login. However, If i start another sshd on another port, it works! (I assume the second sshd loads the same configruation files.) second sshd started with: sudo /usr/sbin/sshd -p 54321 -d #-d is optional and prints debug output ssh strange-host -p 22 -vvv prints: debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Offering public key: /home/me/.ssh/id_dsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 528 bytes for a total of 2389 debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug2: we did not send a packet, disable method debug3: authmethod_lookup password ssh strange-host -p 54321 -vvv prints: debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password debug1: Offering public key: /home/me/.ssh/id_dsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 528 bytes for a total of 2389 debug1: Server accepts key: pkalg ssh-dss blen 433 debug2: input_userauth_pk_ok: SHA1 fp 0f:1c:df:27:f7:86:49:a8:47:7e:7f:f3:32:1c:7d:04:a3:73:a5:72 So the question is why the difference? I have thought of no way to get any helpful logging from the "standard" sshd to troubleshoot the problem.

    Read the article

  • Security Token for Mac/Linux/Windows, self-managed, pref. open source?

    - by DevelopersDevelopersDevelopers
    I'm looking to buy an evaluation security token (combined smart card/usb reader) for my business that works on: Windows 7 x64 OS X 10.6.x x64 Ubuntu Linux (64 or 32 bit, 10.04 or 10.10, I can bend based on possible tokens) Functionality I need is: Login authentication Authentication for whole-disk encryption (in Linux/Windows, Mac is flexible here) Signing/encryption using PGP and x.509 certificates RSA-2048 key-capable (1024 not good enough.) I can manage the certificates myself Open source middleware/drivers (not necessarily FOSS, just source available. Can flex on this, I just want to be able to audit the code. OpenSC-compatible on Linux would be great.) Is there any token that can do all of this? Or would I need multiple ones to accomplish this? Or do I need to look at smart cards and readers to get this? I have been researching this for a while and have had a heck of a time even getting accurate information about products. Also, I am in the USA, and it appears that EU export laws prevent me from buying from there, so those vendors are out. I was looking at Feitian tokens from Gooze, but since they are in France I can't buy.

    Read the article

  • Why is my new PC so slow at startup?

    - by rumtscho
    Bought a new PC this weekend, and it works really good. Only I have one big problem: startup time. Its BIOS needs 62 sec to load, then from Grub start to pw entering screen it's another 26 sec. I think this is a lot, because my old PC needs 34 sec for BIOS and another 8 sec to pw screen. After I enter the pw, the desktop is usable with practically no delay on both. The new PC is a core i7-930, running a Lucid Lynx 64 bit from a Intel Postville SSD (no internal HDs). The old PC is a Pentium 4 celeron (forgot the clock speed) running a Lucid Lynx 32 bit from an ATA 100 hard drive. Neither PC is overclocked. The new one has boot sequence 1.DVD ROM, 2.SSD (connected over SATA in AHCI mode), 3. removable drive. The old one boots from 1. DVD ROM, 2. HDD, 3. Floppy. Neither has a second OS installed. The new one has less software installed than the old one (I think), but the boot time difference was noticeable even before I made any installs. As far as I know, just the SSD should be enough to make a noticeable difference in boot time. I thought that having a good mainboard on the new PC as opposed to the basic office model on the old one would also mean a faster loading BIOS. If these assumptions are right, I guess I must have misconfigured something in the BIOS of the new PC. How should I configure it for a fast boot? It has an ASUS P6X58D board with an AMI BIOS, if you need the BIOS revision number I could post that too.

    Read the article

  • My server cant resolve domains?

    - by Nuker
    I am on a VPS that is pretty much unmanaged so it means im on my own. I did my best to configure it so i can host my own site for other people to see it online but seems like i have network problems because in the last days many of my users report they cant enter my site from my domain and seems like Google and Facebook cant either (this never happened before). Its weird because i can enter my site without problems and so many other people as well. But then i tried to make a php include and i get this error: Warning: include(): php_network_getaddresses: getaddrinfo failed: Name or service not known in I was told that seems like my server cant resolve domains. The includes work if i use IPs instead of domains. So it means i have a DNS problem or something? What can i do to fix it? Im on a Linux 2.6.32-431.11.2.el6.x86_64 on x86_64 CentOS Linux 6.5 Thank you. EDIT: i have this on my resolv.conf # Generated by NetworkManager # No nameservers found; try putting DNS servers into your # ifcfg files in /etc/sysconfig/network-scripts like so: # # DNS1=xxx.xxx.xxx.xxx # DNS2=xxx.xxx.xxx.xxx # DOMAIN=lab.foo.com bar.foo.com nameserver 8.8.8.8 nameserver 8.8.4.4

    Read the article

  • Apache downloads php files instead of running their source

    - by Devils Child
    I have just recently upgraded PHP 5.3 to 5.4 on my Debian Squeeze server. Now, instead of executing PHP files, Apache just downloads them, which is really bad. When I try to follow these steps, I get "broken packages" upon installing the libapache2-mod-php5 package. Also the answer tells me to add something to my httpd.conf, but it's empty. Question: How can I make apache execute php files again, instead of just passing them through as download? dpkg -l | grep php returns this rc libapache2-mod-php5 5.3.3-7+squeeze15 server-side, HTML-embedded scripting language (Apache 2 module) rc php5-cli 5.3.3-7+squeeze15 command-line interpreter for the php5 scripting language ii php5-common 5.4.15-1~dotdeb.2 Common files for packages built from the php5 source rc php5-gd 5.3.3-7+squeeze15 GD module for php5 rc php5-mcrypt 5.3.3-7+squeeze15 MCrypt module for php5 rc php5-mysql 5.3.3-7+squeeze15 MySQL module for php5 rc php5-suhosin 0.9.32.1-1 advanced protection module for php5 rc phpmyadmin 4:3.3.7-7 MySQL web administration tool And apt-get install libapache2-mod-php5 produces this error The following packages have unmet dependencies: libapache2-mod-php5 : Depends: libdb5.1 but it is not installable Depends: libssl1.0.0 (>= 1.0.0) but it is not installable Depends: libxml2 (>= 2.8.0) but 2.7.8.dfsg-2+squeeze7 is to be installed Recommends: php5-cli but it is not going to be installed E: Broken packages

    Read the article

  • windows 2008 r2 iis worker proccess memory usage increase

    - by nLL
    I have this web site written in c#. around 400-500 users online at any time. it was on windows 2008 32 bit machine before and never ever locked/slowed down due to increased memory consumption up until i upgraded it's server to win 2008 r2 64 bit. Old server had only 4 gig ram and quad core cpu at 2ghz. site was working just fine. since i've upgraded the server i noticed (2 times with in 10 days) it started to eat ram. last night it went up to 4 gb ram. with ram increase response slows down quite a lot. recycling app pool doesn't help. I have to restart it's worker process to recover. i've noticed this usually happens if there are continuous errors. as i didn't change anything in the code am i safe to assume it is not related to memory leak in the code? did anyone came across something like that? same thing happens if i create continuous errors with classic asp. thanks

    Read the article

  • Can I use HP Recovery Discs for a different hard drive capacity and make?

    - by Fasih Khatib
    About two years ago I created HP Recovery Discs (3 of them). Now my hard drive has crashed and new one is still a week from delivery. I was reading up on how to reinstall the genuine OS using the Recovery Discs as i was not given any Windows 7 installation discs. I did my bit of research after getting answers from the community on what these discs do and found out on other sites that people experience issues when recovering their OS from the disc. Especially when they change the make or capacity of the harddrive. Unfortunately I had to change the make as the hard drive that came built in has gone out of production. This question is just a part of my checklist to avoid problems when recovering the OS. I have: HP DV4-2126TX (available only in India I guess) I had: Seagate Momentus 320 GB I ordered: Western Digital Scorpio Black 500 GB Windows 7 Home Premium 32-bit Is there a possibility to encounter any problems due to the changed capacity and make? I only want my genuine OS and drivers – not my data. I was told that Disc 1 contained the OS and drivers, and the rest of the discs contained data. I couldn't verify that.

    Read the article

  • Sound doesn't work anymore after replacing RAM

    - by thejh
    Hello, today, I replaced one old RAM module with two newer, bigger ones, but now, the sound doesn't seem to work anymore. Already ran alsaconf and it didn't help. Output of lspci for the audio device: 00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1) Subsystem: Giga-byte Technology Device a002 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at f5100000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel The audio device is onboard and has six configurable outputs, two or so are also capable of being an input (if I remember it correctly), but I don't know how to control it under linux. Does somebody know how/whether replacing the RAM could be related to my problem and/or how to fix it?

    Read the article

  • Is 40+ Logons on Exchange 2003 per user normal?

    - by cbsch
    Hello! We've had a problem at work where users sometimes randomly can't connect to exchange. I've found out that it's because they reached the limit of 32 concurrent logons. I increased the maximum allowed connections by adding the key "Maximum Allowed Sessions Per User" in HKLM\SYSTEM\CurrentControlSet\Services\MSExchangeIS\ParametersSystem. But I'm not sure if this is a real good fix. Looking at the logons some users has as many as 15 logons with the exact same logon time. I know for sure that Outlook 2007 does this, as I was watching them while a user connected with Outlook after a restart on the Exchange service. Every user also has an iPhone connected to exchange, I don't know if these cause the same thing. Is this normal? Could there be a bug in the software? (The Outlook 2007 has nothing configured, except added the user, pure vanilla installs). The users are mobile, and when Outlook generates up to 15 connection every time it connects, and I've read (no sources, sorry) that Outlook doesn't time out connections before 2 hours. I might have to set this number real high to prevent it from being a problem.

    Read the article

  • How to fix missing RAID1 drive

    - by Sodved
    I had to do some fiddling about with my cables inside thebox and now I am getting a "Critical Error" about the RAID disks during startup. I have a gigabyte GA-MA770T-UD3 motherboard. Aparently the RAID controller is an AMD SB710 chip. I'm pretty sure I know what happenned. The first time I rebooted I had forgotten the power cable on one of the disks in the RAID1 (mirror) and let it boot up. So I shut down and put the power back in. So now when it boots up I go into the RAID admin interface (between the BIOS screen and the OS loading): it shows the RAID1 as in error the logical device has one disk and says the other is disconnected or missing the other physical disk shows up as a single disk If I boot to the OS (Windows 7 32 bit) the data all seems to be there. If I go into computer management it says my partition is on a disk and working OK. But the other disk is offline because: "The disk is offline because it has a signature collision with another disk that is online" So I am guessing because I STUPIDLY booted up with only one of the disks powered on, the other disk fell out of synch with the mirror and so now cannot rejoin the mirror. How do I fix this? I want to get the RAID1 mirror working again. There does not appear to be any "Repair" option in the basic RAID admin tool which I get into during startup before the OS boots. I have not made any explicit changes to the online one (but I guess the OS has probably written some admin data).

    Read the article

  • Can't get 1440x900 resolution with GRUB2 although vbeinfo says it's available

    - by TomSW
    I'm trying to use GRUB2 in graphical mode with 1440x900 resolution, but the result is always garbled nonsense: the highest resolution I can get is 1280x800. Word is from googling that long as vbeinfo lists a resolution, GRUB2 can use it. This doesn't seem to be true: vbeinfo says that 1440x900 is available but it doesn't work. Testing it from the GRUB2 command line: set gxfmode=1440x900 terminal_output gfxterm # -> garbled nonsense # back to trusty 640x480 terminal_output console The graphics card is an Intel GM965. Once linux boots the framebuffer switches to 1440x900. Added after epheminent's reply and various experiments vbeinfo lists two sets of modes. The first set runs from 0x160 to 0x16b, with resolutions 768x480, 960x600, 1280x800 and 1440x900 Then - after a bunch of text-only modes - the second set, containing resolutions 1024x768, 800x600, and 640x480 The first set of modes aren't altered by 915resolution. They all work except 1440x900. The resolution of modes in the second set can be altered using the 915resolution module / command available in GRUB2 = 1.99. # in /boot/grub/grub.cfg insmod 915resolution # 30, 32, 34 all work for me: all that varies is which modes are altered 915resolution 30 1440 900 # setting an impossible resolution changes the mode to "text-only" # in my case 1280x1024 is not supported 915resolution 30 1280 1024 Clearly, 1440x900 should just work: adding it with 915resolution is just a workaround.

    Read the article

  • Huh? JDK not found? (on Windows 7 64-bit)

    - by Android Eve
    I am setting up a development environment for the latest Android 2.3 on a fresh install of Windows 7 64-bit. I first installed the 64-bit JDK 6 (jdk-6u23-windows-x64.exe). Then, I installed 64-bit Eclipse Classic 3.6 (eclipse-SDK-3.6.1-win32-x86_64.zip). Then, I proceed to install the Android SDK Starter Package: installer_r08-windows.exe. But... upon start it says: "Java SE Development Kit (JDK) not found." Why? I just installed it. Is this a mismatch between 32-bit and 64-bit? How do I solve this? Update (1): I tried setting the %JAVA_HOME% environment variable, as well as setting the Installed JREs in Eclipse, as suggested below. None of these solved the problem. It appears that I am not the only experiencing the problem, as this thread suggests: http://stackoverflow.com/questions/1919340/android-sdk-setup-under-windows-7-pro-64-bit I wonder whether there is a 64-bit version of the Android SDK. Update (2): I used the zip version instead (android-sdk_r08-windows.zip), ran android.bat, updated all SDK packages, and installed the ADT plugin (8.0.1), not before having to check: 'Contact all update sites during install to find required software'. We'll see how this goes... Update (3): It worked! (going to accept @bubu's answer shortly) -- but why doesn't the emulator include the HelloAndroid app when I run it (Ctrl+F11) from Eclipse?

    Read the article

< Previous Page | 215 216 217 218 219 220 221 222 223 224 225 226  | Next Page >