Search Results

Search found 8656 results on 347 pages for 'boot to vhd'.

Page 222/347 | < Previous Page | 218 219 220 221 222 223 224 225 226 227 228 229  | Next Page >

  • Hard Drive Bad Sector marking utility

    - by Kevin Boyd
    I already have Windows XP, During installing Ubuntu(dual boot) the disk drive just stuck up at one place and doesn't seem to move ahead.. Is there a disk bad sector mark utility that just marks these sectors so that the disk doesn't seek them later. I tried running Seagate Seatools on the drive but both the short test and long test fail even before they start even chkdsk /f/r doesn't seem to work as the system locks up at stage four.

    Read the article

  • ESX Install........

    - by ov4
    HI all, I recently purchases a bunch of r710 from dell, i installed esx on it. the installation process finished without a problem. however once the esx boot the following error displays at the botton with red letters 00:00:02:21.493 cpu11:4119) mod:2971: Initialization for vmfs2 failed with -1 i installed on two different servers and the same error pops up. the curius thing is that if i install esxi 3.5 or 4 there is not problem help Thanks Oscar

    Read the article

  • How to setup 802.11n wireless card in ubuntu

    - by michael
    Hi, I have installed ubuntu 9.10 on my laptop. It has a 802.11n wireless card. When I boot up to ubuntu, the wireless does not work. And if I connect to a wire network within ubuntu, it works. Can you please tell me how can I setup my wireless card in ubuntu 9.10? Thank you.

    Read the article

  • System failure - need diagnostic recommendation

    - by Ladislav Mrnka
    I have big problem with my computer. Configuration is: Intel i7 + 6x2GB OCZ DDR3 Motheboard: Asus P6T Deluxe V2, HDD controller configured to AHCI Main drive: OCZ Vertex 2 (SSD) - contains all installed programs and system Second drive: Samsung SpinPoint - contains User profiles, ProgramData, virtual machines and databases Third drive: Samsung SpinPoint - data drive + backups OS: Windows 7 Ultimate x64 I have never had any problem with this computer until now. During weekend my computer completely crashed without any reason. Each time I tried to boot to Windows I got BSOD with message BAD_SYSTEM_CONFIG_INFO and automatic restart (I didn't install any new SW or HW). But after restart main OCZ drive was disconnected (not detected by BIOS). When I turned off and on computer, the drive was again connected. It also happend every single time I tried to repair installation somehow. It ended with some error and after restart drive was disconnected. The only thing which worked was format + fresh install. After installing almost everything I wanted to install Visual Studio 2010 Ultimate (complete installation without SQL Server Express). During installation of VS itself I always get BSOD - it is too fast so I'm not able to read description. After restart it searches for all disk drives for really long time and sometimes it changes boot drive so the system is not able to start - Bootmgr not found. After reconfiguring BIOS the system starts. There is no event describing the failure in Event viewer. Installing VS 2010 is absolutely necessary for me. I need help with diagnostic. I need to find where is the problem - I expect that the problem is in OCZ drive or in HDD controller on motherboard but I don't know how to find it. All components still have valid warranty. Can you recommend me some approach or tools to find the problem? Edit: I'm still looking for source of the problem. New information is that Windows are not able to perform check disk (Chkdsk) on the SSD system drive. After restarting it always starts checking drive and in part where files are checked it fails with BSOD - BAD_SYSTEM_CONFIG_INFO. After next restart and skipping check disk tests the system runs.

    Read the article

  • Computer suddenly dies; screen displays weird flickering lines, then restarts

    - by Imray
    I've been having this terrible problem for a little while and just managed to get a picture of 'dead screen' for the first time and I am posting it to seek help. Randomly, at irregular intervals (typically once a week), while working on something (it's been different things every time) my computer will just suddenly go dead - the screen turns to exactly the picture below (the lines flicker a little bit), it hangs there for a few seconds and then restarts. Obviously this is extremely frustrating and I want to try to stop it. I've searched numerous postings with similar keywords but nothing exactly the same as mine. Does anyone have any idea what might be the cause of this? I would post all my system settings and installed programs but the list is long and I don't know how much relevance each item would be. If you'd like to know something specific, please comment and I'll let you know whatever you need. SPECS C:\Users\Imray>systeminfo Host Name: Imray OS Name: Microsoft Windows 7 Professional OS Version: 6.1.7600 N/A Build 7600 OS Manufacturer: Microsoft Corporation OS Configuration: Standalone Workstation OS Build Type: Multiprocessor Free Registered Owner: Imray - Owner Registered Organization: Product ID: 00371-152-9333854-85895 Original Install Date: 06/09/1999, 5:45:21 PM System Boot Time: 22/03/2013, 8:58:18 AM System Manufacturer: Gateway System Model: DX4840 System Type: x64-based PC Processor(s): 1 Processor(s) Installed. [01]: Intel64 Family 6 Model 37 Stepping 2 GenuineIntel ~3201 Mhz BIOS Version: American Megatrends Inc. P01-A3 , 17/05/2010 Windows Directory: C:\Windows System Directory: C:\Windows\system32 Boot Device: \Device\HarddiskVolume2 System Locale: en-us;English (United States) Input Locale: en-us;English (United States) Time Zone: (UTC-05:00) Eastern Time (US & Canada) Total Physical Memory: 6,135 MB Available Physical Memory: 3,632 MB Virtual Memory: Max Size: 12,268 MB Virtual Memory: Available: 8,114 MB Virtual Memory: In Use: 4,154 MB Page File Location(s): C:\pagefile.sys Domain: WORKGROUP Logon Server: \\Imray-OWNER Hotfix(s): 4 Hotfix(s) Installed. [01]: KB971033 [02]: KB958559 [03]: KB977206 [04]: KB981889 Network Card(s): 2 NIC(s) Installed. [01]: 802.11n Wireless PCI Express Card LAN Adapter Connection Name: Wireless Network Connection DHCP Enabled: Yes DHCP Server: 192.168.2.1 IP address(es) [01]: 192.168.2.13 [02]: fe80::1df1:5399:6890:91f6 [02]: Microsoft Virtual WiFi Miniport Adapter Connection Name: Wireless Network Connection 2 DHCP Enabled: Yes DHCP Server: N/A IP address(es) Graphics Card Specs Name ATI Radeon HD 5570 PNP Device ID PCI\VEN_1002&DEV_68D9&SUBSYS_E142174B&REV_00\4&18A4B35E&0&0008 Adapter Type ATI display adapter (0x68D9), ATI Technologies Inc. compatible Adapter Description ATI Radeon HD 5570 Adapter RAM 1.00 GB (1,073,741,824 bytes) Installed Drivers atiu9p64 aticfx64 aticfx64 atiu9pag aticfx32 aticfx32 atiumd64 atidxx64 atidxx64 atiumdag atidxx32 atidxx32 atiumdva atiumd6a atitmm64 Driver Version 8.700.0.0 INF File oem1.inf (ati2mtag_Evergreen section) Color Planes Not Available Color Table Entries 4294967296 Resolution 1920 x 1080 x 59 hertz Bits/Pixel 32 Memory Address 0xD0000000-0xDFFFFFFF Memory Address 0xFBDE0000-0xFBDFFFFF I/O Port 0x0000D000-0x0000DFFF IRQ Channel IRQ 4294967293 I/O Port 0x000003B0-0x000003BB I/O Port 0x000003C0-0x000003DF Memory Address 0xA0000-0xBFFFF Driver c:\windows\system32\drivers\atikmpag.sys (8.14.1.6095, 181.00 KB (185,344 bytes), 06/09/1999 5:59 PM)

    Read the article

  • Applications Deployment with MDT

    - by beakersoft
    I have added a install for Silver light to my MDT server, so it can get installed when the image gets deployed. When I boot them machines it is asking me to install the applications, how can i get it to auto install the apps without prompting. I have added this line to the rules - I thought that would but seems to make no difference. I'm sure i must have missed something somewhere? Cheers Luke

    Read the article

  • I have 2 identical windows 2008 r2 servers with 32G RAM, one shows "Installed Memory(Ram): 32.0GB" a

    - by c0m4
    the server model: HP Poliant DL160 G5, both servers have identical product ID. for some reason one of the servers have 4GB ram reserved. it shows in the memory tab on the Resource monitor as "Hardware Reserved". I've googled it a bit and found some post related to msconfig boot parameters (but mine are properly set) and some post related to memory remap option in the bios but it is not available in my servers bios so in a bit lost... help?

    Read the article

  • Is it okay to use a SSH key with an empty passphrase?

    - by mozillalives
    When I first learned how to make ssh keys, the tutorials I read all stated that a good passphrase should be chosen. But recently, when setting up a daemon process that needs to ssh to another machine, I discovered that the only way (it seems) to have a key that I don't need to auth at every boot is to create a key with an empty passphrase. So my question is, what are the concerns with using a key with no passphrase?

    Read the article

  • lshw tells me my processor is a 64 bits but my motherboard has a 32 bits width

    - by bpetit
    Recently I noticed lshw tells me a strange thing. Here is the first part of my lshw output: bpetit-1025c description: Notebook product: 1025C (1025C) vendor: ASUSTeK COMPUTER INC. version: x.x serial: C3OAAS000774 width: 32 bits capabilities: smbios-2.7 dmi-2.7 smp-1.4 smp configuration: boot=normal chassis=notebook cpus=2 family=Eee PC... *-core description: Motherboard product: 1025C vendor: ASUSTeK COMPUTER INC. physical id: 0 version: x.xx serial: EeePC-0123456789 slot: To be filled by O.E.M. *-firmware description: BIOS vendor: American Megatrends Inc. physical id: 0 version: 1025C.0701 date: 01/06/2012 size: 64KiB capacity: 1984KiB capabilities: pci upgrade shadowing cdboot bootselect socketedrom edd... *-cpu:0 description: CPU product: Intel(R) Atom(TM) CPU N2800 @ 1.86GHz vendor: Intel Corp. physical id: 4 bus info: cpu@0 version: 6.6.1 serial: 0003-0661-0000-0000-0000-0000 slot: CPU 1 size: 798MHz capacity: 1865MHz width: 64 bits clock: 533MHz capabilities: x86-64 boot fpu fpu_exception wp vme de pse tsc ... configuration: cores=2 enabledcores=1 id=2 threads=2 *-cache:0 description: L1 cache physical id: 5 slot: L1-Cache size: 24KiB capacity: 24KiB capabilities: internal write-back unified *-cache:1 description: L2 cache physical id: 6 slot: L2-Cache size: 512KiB capacity: 512KiB capabilities: internal varies unified *-logicalcpu:0 description: Logical CPU physical id: 2.1 width: 64 bits capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 2.2 width: 64 bits capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 2.3 width: 64 bits capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 2.4 width: 64 bits capabilities: logical *-memory description: System Memory physical id: 13 slot: System board or motherboard size: 2GiB *-bank:0 description: SODIMM [empty] product: [Empty] vendor: [Empty] physical id: 0 serial: [Empty] slot: DIMM0 *-bank:1 description: SODIMM DDR3 Synchronous 1066 MHz (0.9 ns) product: SSZ3128M8-EAEEF vendor: Xicor physical id: 1 serial: 00000004 slot: DIMM1 size: 2GiB width: 64 bits clock: 1066MHz (0.9ns) *-cpu:1 physical id: 1 bus info: cpu@1 version: 6.6.1 serial: 0003-0661-0000-0000-0000-0000 size: 798MHz capacity: 798MHz capabilities: ht cpufreq configuration: id=2 *-logicalcpu:0 description: Logical CPU physical id: 2.1 capabilities: logical *-logicalcpu:1 description: Logical CPU physical id: 2.2 capabilities: logical *-logicalcpu:2 description: Logical CPU physical id: 2.3 capabilities: logical *-logicalcpu:3 description: Logical CPU physical id: 2.4 capabilities: logical So here I see my processor is effectively a 64 bits one. However, I'm wondering how my motherboard can have a "32 bits width". I've browsed the web to find an answer, without success. I imagine it's just a technical fact that I don't know about. Thanks.

    Read the article

  • how to restore os using acronis

    - by user23950
    I have made a backup using Acronis 2010. And I've tested it on vmware. And I'm having problems booting up the dual boot vm. After restoring from the .tib file. What do I do?What other software that can image the os can you recommend that is easier to use than Acronis.

    Read the article

  • DVD drive not recognized

    - by David Oneill
    I'm in the midst of building a computer (first time builder) I got everything plugged in, and hit the power button. After the excitement of the first boot coming up on my screen, I was looking through the BIOS settings. However, joy soon turned sour, as I looked at the list of installed SATA devices. My DVD drive wasn't on the list :( So, what are common things I should check/try?

    Read the article

  • Recover strategy single bad sector in moricon

    - by Damon
    This week, my harddisk made me an early christmas present in the form of a single defect sector. To make up for the puny size of the present, it chose a sector inside moricons.dll for that. This means that now the system takes about 5 minutes to boot before Windows gives up and moves on, and there's 2 dozen scary "critical failure" entries in the system log after every boot, which is annoying. OK, admittedly, I shouldn't complain, it could be worse, the bad sector could be in ntldr... SMART info more or less indicates (for what SMART can indicate anyway) that the drive is mostly OK. Soft Read Error Rate has a score of 96, and Current Pending Sector Count has a raw value of 8, which translates to a score of 100. Acronis DriveMonitor makes this an issue (lowering the overall rating to 75%), HDD Health calls it "excellent", giving an overall rating of 95% (which is what this harddisk from day one). No single score is below 95 (power on hours and spin up count), and most are 100 anyway. Well, whatever, I've seen drives with perfect SMART values fail from one second to the other, and drives with moderate values work for years. So, I'm inclined not to put too much weight into that overall. TL;DR Now... to the problem: I don't feel like trashing the disk just yet (that's planned with a new OS install upgrading to Win7 early next year, independently of this issue), but in the mean time, I would still like to have a smoothly running system again. Therefore, I feel tempted to tamper with it, but before I render my system entirely unusable (since I've never done this before), I'd like to verify that my planned procedere is likely to suceed in having a working system again: Copy moricons.dl_ from the Windows install disk, rename it to moricons.zip, and unzip it. This gives an intact 5.1.2600.2180 version (the broken one is 5.1.2600.5512 - but I guess this makes not much of a difference, since it's an icon-only DLL, and an outdated copy should work better than one that can't be read) Run chkdsk /r /f` which will "repair" the file (i.e. delete the file without asking, tell the drive to remap the sector, and toss some unreadable junk into a file with a hexadecimal number) Hopefully Windows still boots after this (is that a reasonable expectation, or do I need to have something like BartPE ready? -- but then again, what's that good for in case chkdsk has nuked the entire file system...) Delete the junk file generated by chkdsk, copy the new DLL to %windir%\system32 Reboot. Pray. Maybe I just shouldn't touch anything, since it still kind of works... if annoying, but it works. Unsure... But, is there anything fundamentally wrong with the planned approach? Is this a sensible approach at all?

    Read the article

  • Rolling back Server edition from GRUB List (Ubuntu)

    - by A.Rashad
    I seems i did some mistake, and installed Ubuntu server on my home based ubuntu box. and the problem is that GRUB places the server edition as a priority boot in the menu, especially when I upgrade the kernel or the release. How can I remove the server from the GRUB menu permanently? can I un-install Ubuntu server edition?

    Read the article

  • How do I configure a guest VM's static IP address automatically in Citrix XenServer?

    - by Kev
    To facilitate automation of guest VM provisioning, how do I set (in a script) the IP address on a guest VM's NIC (or NIC's) once a new VM has booted? Is there a way to "inject" netsh commands via the Citrix guest OS tools (for Windows for example) once the host has started? Or can this be done via the Citrix API/SDK or the xe tools? These are windows 2008 servers that have been sysprep'd so when the boot for the first time they have no IP address.

    Read the article

  • Solaris SPARC 10 32bit mode

    - by TM.
    I'm looking for a definitive answer, does Solaris 10 running on a SPARC machine support booting into 32bit mode? I've found one site that states Solaris 8 was the last version that supported booting in a 32bit mode for SPARC. I've read multiple items that explain how to boot Solaris into 32bit mode, however they did not list the Solaris version. We've tried all the ways specified, but the system keeps booting into 64bit mode.

    Read the article

  • Terminal window opens when Xubuntu starts...?

    - by james
    Whenever I start up my laptop with Xubuntu on it, a Terminal window opens and just sits in the taskbar - as though I opened it myself. Anyone know if there's some sort of list of applications which open at boot time. Maybe Terminal got on that list somehow?

    Read the article

  • Why did my graphics card explode?

    - by C-dizzle
    How did my graphics card "explode" like it did in the picture I have here? And if I was just plugging into my on-board graphics, why wouldn't the PC boot up like it normally would? It wouldn't come up until I opened the cover and removed the card, that's when I found it like this. EDIT: If the card was trying to still operate like this for a while, did it run the risk of damaging the PCI-E slot?

    Read the article

  • Cron Job that Boots Screen at Start

    - by Pez Cuckow
    I am trying to set up a number of processes that start during boot (servers for games) with the below command as the cron item: @reboot /usr/bin/screen -fa -d -m -S NAME COMMAND However if the server crashes for what ever reason screen closes and the server doesn't get a chance to run it's auto restart (as far as I understand; screen sees no processes in the socket and so closes). Is there a way that I can get around this so screen will sit there even if nothing is running in it?

    Read the article

  • Windows Server 2008 R2 bare metal restore to different hardware

    - by S Falken
    Scenario: I have a Windows Server 2008 R2 x64 installation whose main disk drive is now 7 years old and showing signs of age. For the last couple of months it's been displaying increased errors and requirements to run checkdisk. I have successfully created a bare metal restore (BMR) image on a separate data drive on the server, which can be seen from the Windows Recovery console; I tested it by booting to and using the Windows Server installation DVD's recovery utilities. The BMR image includes the system drive with boot partition, system state, and the D:\ drive of the server, which is where I have followed the practice of installing any program that does not require a C:\ installation path. Therefore, the BMR includes both the C:\ and D:\ drives, system state and boot partition. The C:\ drive is a 7-year old Seagate 160GB. The D:\ drive is a rather newer 120GB Western Digital. I have purchased a 128GB solid state Samsung 830 that I want to restore these partitions to, using the BMR. Questions: In the above-referenced article, Microsoft seems to be indicating that I am only able to restore to like-kind hardware, which doesn't help at all and is difficult to believe. Is this really true? I've cleaned these drives up and minimized the size of partition they require. C:\ will need about a 70GB partition, and the data on D:\ will need about 50GB. Will Windows Server backup allow me to restore the BMR to newly-created partitions on the SSD, discarding extra space? I don't need a "how-to": I just need an "is it possible". Justification: Before posting this question, I checked ServerFault articles with the following titles, but none of them were about this exact scenario: Restore SBS 2008 Backup to Same Hardware but Different Disk Configuration Restoring Windows Server 2008 to different hardware - OEM License Restoring II6 server after a hardware failure windows 2008 r2 fail to restore Domain controller failed to restore using windows backup tools How does restore to dissimilar hardware work? Migrating Windows 2008 R2 from a PC to a different PC TFS 2005 Server restore from one hardware to another I also researched Microsoft but only received an oblique answer which was not precisely aimed at my question, at the following URL: http://support.microsoft.com/kb/249694#method3

    Read the article

  • keyboard works in the BIOS(except a), but not at the password screen(win 7, 64bit)

    - by christoffer svendsen
    The computer is a acer aspire 7720g laptop. When windows want me to input my password, the only keys working is caps lock, the numpad and the m key(and the m key works like a combined m and enter key). I did spill some water on the keyboard yesterday but the same thing happens with usb keyboards. I disabled the quick boot in the bios, making it go through every test at bootup, which resulted in continous beeping from the computer. Anyone know how to solve this?

    Read the article

< Previous Page | 218 219 220 221 222 223 224 225 226 227 228 229  | Next Page >