Search Results

Search found 8830 results on 354 pages for 'enterprise deployment'.

Page 225/354 | < Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >

• NetApp and SQL Server?

  - by Edinor

  Do you have any good or bad experiences to share running SQL Server OLTP Systems on NetApp appliances? I have been working with a small, relatively low-volume cluster with a lower-end NetApp device, and I have found the environment to be generally unstable, at least compared to my experiences with other SANs, iSCSI arrays, and DAS setups. I struggle to believe that RAID DP and WAFL are more than fairy-dust technologies. A solution has been proposed to me that I just need a bigger, better NetApp, with PAM cards and other cool technology I've not heard of, and I feel like I would be better off spending a quarter of that on good direct-attached drives and a beefy server. At the same time, I feel that an Enterprise-class SAN should be something I can count on to be consistently a more stable, better performer than the less expensive solution I might propose. Are you a SQL Server DBA in an OLTP environment and love your NetApp? If you don't like them, why not?

  Read the article

• Hyper-V VMs hanging 10 minutes after startup

  - by Ken George

  Hyper-V running under a fresh install of 2008 R2 DC 2 VMs both running 2008 R2 STD One VM has SQL 2008 Server w/ SP2 and Office 2007 Enterprise w/ SP2 Othe VMS only Office 2007 w/ SP2. Approximately 10 minutes after reboot the Hyuper-V host the VMs will hang Hang = answers pings, but no RDP connections and Hyper-V console session is non responsive Disabled Hyper-V and had no proble with 2008 R2 DC host. Started the three Hyper-V services and 10 minutes later was hung again. Hardware is HP DL380 G4 2 socket, 48 GB, Internal SAS controller 1.5TB C drive VMs .VHDs are on external SAS controller on a 1.5 TB RAID5 volume. Nothing in event log on either VMs or Hyper-V host. Ken

  Read the article

• redirect traffic to www.example.com through DNS from example.com

  - by ChrisMuench

  Hello, I have a bit of a unique problem. for the domain (example.com) I want people to go to www.example.com however I'm also throwing GSLB into the mix. for GSLB the devices(one in each datacenter) need to be the nameserver for portion of the domain that they are going to answer for(www.example.com) so I know I can make the NS record of www.example.com just fine and have it point to each GSLB device. However that only helps for www.example.com NOT example.com. I don't want to make my root NS of example.com my GSLB as my enterprise managed DNS provider does an excellent job of all DNS stuff. any ideas?

  Read the article

• How do I make kdump use a permissible range of memory for the crash kernel?

  - by Philip Durbin

  I've read the Red Hat Knowledgebase article "How do I configure kexec/kdump on Red Hat Enterprise Linux 5?" at http://kbase.redhat.com/faq/docs/DOC-6039 and http://prefetch.net/blog/index.php/2009/07/06/using-kdump-to-get-core-files-on-fedora-and-centos-hosts/ The crashkernel=128M@16M kernel parameter works fine for me in a RHEL 6.0 beta VM, but not on the RHEL 5.5 hosts I've tried. dmesg shows me: Memory for crash kernel (0x0 to 0x0) notwithin permissible range disabling kdump Here's the line from grub.conf: kernel /vmlinuz-2.6.18-194.3.1.el5 ro root=/dev/md2 console=ttyS0,115200 panic=15 rhgb quiet crashkernel=128M@16M How do I make kdump use a permissible range of memory for the crash kernel?

  Read the article

• CheckPoint VPN-1 SecureClient inability to navigate behind a Linksys WAG300N

  - by AndreaTrasatti

  I have a Linksys WAG300N, I'm accessing my LAN with Wifi and everything works fine on my Windows 7 Enterprise laptop. When I try to connect to my company's VPN the connection succeeds, but I cannot access any internet site either within my work network or public site like Yahoo or Google. In my Linksys control panel I already verified all types of VPNs are enable to passthrough. Normal IPSec and Windows VPN worked in the past without any problems. CheckPoint seems to have a solution, but I do not have the ability to change the IP in my client and of course using another NAT device in between is not a solution for me. Edit: adding link to the Checkpoint solution, https://supportcenter.checkpoint.com/supportcenter/portal?eventSubmit_doGoviewsolutiondetails=&solutionid=sk26189

  Read the article

• Windows 7 remote desktop connection does not respond to mouse or keyboard

  - by Daniel Jette

  Pretty much every time I connect to my work PC from home (both running Windows 7), I can see the screen refresh and signs of life (clock changes, notifications pop up), but I cannot interact with the remote machine at all. Mouse and keyboard input are both ignored. If I repeatedly reconnect, I will eventually get a connection that works. I think either a setting on my host machine, VPN client or work network is configured wrong. My home PC is running Windows 7 Professional. My work PC is running Windows 7 Enterprise. My VPN client is Cisco AnyConnect. Is this a problem anyone else has run in to? Any suggestions for settings to tweak?

  Read the article

• Which linux distro for a laptop in windows environmet?

  - by Dev er dev

  I just got new laptop at work. What would you recommend as a linux distribution for it? All other developers are working under windows, and use windows tools. I'm currently using ArchLinux, but want to change it. I don't want to waste time configuring wireless, windows network shares, network pritners, projector, etc ... I want this stuff to just work, while still having sane and stable development evironment and tools. Is Ubuntu a good choice for this? I use gentoo at home, but don't think it is a good match for work environmet. EDIT: Note that we are working on cross platform apps, and deployment platform is almost always linux. There are very few windows apps that I have to use (like MS Project). It is just that everything else is windows centric. I use linux because I feel more productive with it, even if I have to dual boot to edit MS Project files.

  Read the article

• Version `GLIBCXX_3.4.15' not found in CentOS (in file /usr/lib/libstdc++.so.6)

  - by George Kastrinis

  I try to use a program and I get the following error. /usr/lib64/libstdc++.so.6: version `GLIBCXX_3.4.15' not found Under /usr/lib64 the libstdc++ I see is libstdc++.so.6.0.13 (and a soft link). With strings libstdc++.so.6.0.13 | grep GLIBCXX I get GLIBCXX_3.4 GLIBCXX_3.4.1 GLIBCXX_3.4.2 GLIBCXX_3.4.3 GLIBCXX_3.4.4 GLIBCXX_3.4.5 GLIBCXX_3.4.6 GLIBCXX_3.4.7 GLIBCXX_3.4.8 GLIBCXX_3.4.9 GLIBCXX_3.4.10 GLIBCXX_3.4.11 GLIBCXX_3.4.12 GLIBCXX_3.4.13 GLIBCXX_FORCE_NEW GLIBCXX_DEBUG_MESSAGE_LENGTH With cat /etc/redhat-release I get Red Hat Enterprise Linux Workstation release 6.4 (Santiago) So the question in what should I do in order to fix that. Should I install some new packages and if yes which ones?

  Read the article

• Troubleshooting server performance with a hosted server?

  - by ProfessionalAmateur

  We are in a tough spot, we have a hosted server with the following specs: OS: Windows Server 2008 R2 Enterprise SP1 64bit Processor: Intel Xeon X7550 @ 2GHz (8 processors) RAM: 16GB The file system is on a SAN or NAS (not sure). We are seeing very odd issues where a user will open a 25MB .xslb file and it takes literally 60-120 seconds sometimes. The server is just dog slow for excel. Resources are not being pegged, CPU never jumps up, plenty of RAM... it's just oddly slow. Our host has been looking at the issue for several weeks with not much to show for it. Is there a utility I can run myself that will help trackdown our issue? I have found Server Performance Advisor V1.0 Any experience in using it? Our host is ultimately responsible for fixing this, but we are going on 1 month and our users are losing patience. Any tips would be helpful.

  Read the article

• How to configure Apache2 to host Django and PHP on multiple domains simultaneously?

  - by Bert B.

  I have a VPS (Ubuntu 10.04) that hosts multiple domains, one of them being a CodeIgniter (PHP) web app. The others are just static websites, no fancy backend languages required. Well I am starting a new project and want to use Django. I have Django installed, mod_wsgi enabled in Apache2, but when I did the first steps on the documentation (https://docs.djangoproject.com/en/dev/howto/deployment/wsgi/modwsgi/) it seemingly overwrote my existing Apache2 configuration and served up the Django welcome page to all my domains. What should my httpd.conf file should look like so that it doesn't overtake all my domains.

  Read the article

• 2 (or 3 or 4...) websites in IIS, pointing to same ASP.NET application IIS

  - by billfredtom

  I wish to maintain a single a single code base (ASP.NET app) setup at c:\inetpub\wwwroot\myApp, and point several IIS websites at this single code base. Will this be an issue? Will IIS see this as a conflict in resource allocation? Reasons why I want to do it: Each IIS website can then have it's own IP, SSL cert, etc. Each IIS website can have it's own ISAPI filters installed for friendly URLs, etc. Easier to maintain the code base by having single point of deployment

  Read the article

• SQL Server 2005 Reporting Services - Configuration Manager & Management Studio Problems

  - by Nick

  When I open Reporting Services Configuration Manager on my server, an error message appears that says: Reporting Services Configuration Manager An unknown error has occurred in the WMI Provider. Error Code 800706B3 This error appears before I can even attempt to connect to an SSRS instance. In addition to this problem, I'm not able to connect to my SSRS instance via SSMS on my desktop. When I attempt to connect, I get the following error message: Microsoft SQL Server Management Studio Exception has been thrown by the target of an invocation. (mscorlib) Additional information: The operation could not be completed. (WinMgmt) Information about my environment: Server: Win Server 2K3 x64, SQL 2005 x64 SP3 Build 9.0.4053 Desktop: Windows 7 Enterprise x64 Steps I have already taken: I have installed the latest service pack on my server and workstation. I do not see any errors in my event logs.

  Read the article

• Can't Remove Logical Drive/Array from HP P400

  - by Myles

  This is my first post here. Thank you in advance for any assistance with this matter. I'm trying to remove a logical drive (logical drive 2) and an array (array "B") from my Smart Array P400. The host is a DL580 G5 running 64-bit Red Hat Enterprise Linux Server release 5.7 (Tikanga). I am unable to remove the array using either hpacucli or cpqacuxe. I believe it is because of "OS Status: LOCKED". The file system that lives on this array has been unmounted. I do not want to reboot the host. Is there some way to "release" this logical drive so I can remove the array? Note that I do not need to preserve the data on logical drive 2. I intend to physically remove the drives from the machine and replace them with larger drives. I'm using the cciss kernel module that ships with Red Hat 5.7. Here is some information pertaining to the host and the P400 configuration: [root@gort ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.7 (Tikanga) [root@gort ~]# uname -a Linux gort 2.6.18-274.el5 #1 SMP Fri Jul 8 17:36:59 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux [root@gort ~]# rpm -qa | egrep '^(hp|cpq)' cpqacuxe-9.30-15.0 hp-health-9.25-1551.7.rhel5 hpsmh-7.1.2-3 hpdiags-9.3.0-466 hponcfg-3.1.0-0 hp-snmp-agents-9.25-2384.8.rhel5 hpacucli-9.30-15.0 [root@gort ~]# hpacucli HP Array Configuration Utility CLI 9.30.15.0 Detecting Controllers...Done. Type "help" for a list of supported commands. Type "exit" to close the console. => ctrl all show config detail Smart Array P400 in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Cache Serial Number: PA82C0J9SVW34U RAID 6 (ADG) Status: Enabled Controller Status: OK Hardware Revision: D Firmware Version: 7.22 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Ratio: 25% Read / 75% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Logical Drive: 1 Size: 136.7 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 35132 Strip Size: 128 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Unique Identifier: 600508B100184A395356573334550002 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 101 MB, /tmp 7.8 GB, /usr 3.9 GB, /usr/local 2.0 GB, /var 3.9 GB, / 2.0 GB, /local 113.2 GB OS Status: LOCKED Logical Drive Label: A0027AA78DEE Mirror Group 0: physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) Drive Type: Data Array: A Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:1 Port: 1I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM57RF40000983878FX Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 35 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 1I:1:2 Port: 1I Box: 1 Bay: 2 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM55VQC000098388524 Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 36 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Logical Drive: 2 Size: 546.8 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 256 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Completed Unique Identifier: 600508B100184A395356573334550003 Disk Name: /dev/cciss/c0d1 Mount Points: None OS Status: LOCKED Logical Drive Label: A5C9C6F81504 Drive Type: Data Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:3 Port: 1I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2H5PE00009802NK19 Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 37 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 1I:1:4 Port: 1I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM28YY400009750MKPJ Model: HP DG146ABAB4 Current Temperature (C): 31 Maximum Temperature (C): 36 PHY Count: 1 PHY Transfer Rate: 3.0Gbps physicaldrive 2I:1:5 Port: 2I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FGYV00009802N3GN Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 38 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 2I:1:6 Port: 2I Box: 1 Bay: 6 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM8AFAK00009920MMV1 Model: HP DG146BB976 Current Temperature (C): 31 Maximum Temperature (C): 41 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:7 Port: 2I Box: 1 Bay: 7 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FJQD00009801MSHQ Model: HP DG146ABAB4 Current Temperature (C): 29 Maximum Temperature (C): 39 PHY Count: 1 PHY Transfer Rate: Unknown

  Read the article

• Hybrid Shutdown in Windows 8

  - by Moab

  Referring to this article published September 8, 2011, it gives instructions on how to to do a full (non-hybrid) shutdown in Windows 8 from the command line. We have an option in the UI to revert back to the Windows 7 shutdown/cold boot behavior, or since that’s likely a fairly infrequent thing, you can use the new /full switch on shutdown.exe. From a cmd prompt, run: shutdown /s /full / t 0 to invoke an immediate full shutdown. shutdown /s /full /t 0 I tried this in W8 Enterprise RTM trial, but did not work, so I did a shutdown /? and noticed they have changed the command for a Full shutdown It appears the /s switch now does the full shutdown as explained in the MS article, and the /hybrid switch does the hybrid shutdown for fast startup. Can anyone confirm this change in other RTM versions of Windows 8? Any Microsoft docs on this change are welcome.

  Read the article

• Comparison of cloud hosting providers

  - by Abel

  Is there a place where we can compare* the many new arising cloud hosting providers? From reading into each of them, they seem very different and range from just hosting applications (google) to a semi-full enterprise web serving framework (rackspace). Comparing "by hand" takes a lot of time. All have limitations and different prizing, but which are those and how do they compare? I'm looking for an unbiased comparison site, rather then a discussion on "which is the best". * I don't mean a hosting provider comparison site, of which there are many. The properties of cloud hosting providers are remarkably different and don't compare well on classical hosting provider comparison charts.

  Read the article

• Large svn external

  - by MPelletier

  I have a project which uses a large library residing in its own repository. Using: Tortoise-SVN, the server is running an enterprise edition of VisualSVN The project itself has the "standard" structure: trunk tags branches In each branch, tag, and trunk is the library, set as an external (svn:external property). If I get the entire tree, I get the library several times, which is just getting too ridiculously repetitive. Is there a recommended structure for this? Or perhaps a way not to get all externals (because other externals are much smaller, easier to manipulate)?

  Read the article

• setting rpmforge repository for Linux (RHEL)

  - by Ashish

  Hello, I had a Linux centos(5.5) machine, on this i had deployed amavisd (with clamav and spamassassin). Referred these: http://wiki.centos.org/HowTos/Amavisd http://wiki.centos.org/PackageManagement/Yum/Priorities Now I have a linux RHEL machine, details are as follows: (Linux version 2.6.18-164.6.1.el5 ([email protected]) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-46)) x86_64 GNU/Linux Red Hat Enterprise Linux Server release 5.5 (Tikanga)) I want to set up the above mentioned software's on this(RHEL) machine, for that I do (as per the reference link): install yum-priorities but i am unable to install this on my said machine, because the default yum repository provided by RHEL doesn't contain this. How can i deploy the above software's on my RHEL machine, suggest any safe alternate. Please guide since i am a newbie in this matter. thanks in advance Ashish Sharma

  Read the article

• Windows Server 2012 & Exchange Server 2013 CAL's

  - by Joey Harris

  Trying to build an Exchange server solution for a company and they want me to look into licensing for Windows. I'm going to be purchasing the necessary server licenses for Windows Server 2012 Standard and Microsoft Exchange 2013 Enterprise. I just have a few questions about the CAL's thing which seems like a complete ripoff to me. How are CAL's tracked for both Windows Server and Exchange? Is it tied to Active Directory profiles? What happens if I dont have the necessary CAL's for Windows Server? Will a client be denied access from Active Directory? Is there any enforcement for this? Also the same question for Exchange 2013 CAL's Thanks

  Read the article

• Nexenta/OpenSolaris filer kernel panic/crash

  - by ewwhite

  I've an x4540 Sun storage server running NexentaStor Enterprise. It's serving NFS over 10GbE CX4 for several VMWare vSphere hosts. There are 30 virtual machines running. For the past few weeks, I've had random crashes spaced 10-14 days apart. This system used to open OpenSolaris and was stable in that arrangement. The crashes trigger the automated system recovery feature on the hardware, forcing a hard system reset. Here's the output from mdb debugger: panic[cpu5]/thread=ffffff003fefbc60: Deadlock: cycle in blocking chain ffffff003fefb570 genunix:turnstile_block+795 () ffffff003fefb5d0 unix:mutex_vector_enter+261 () ffffff003fefb630 zfs:dbuf_find+5d () ffffff003fefb6c0 zfs:dbuf_hold_impl+59 () ffffff003fefb700 zfs:dbuf_hold+2e () ffffff003fefb780 zfs:dmu_buf_hold+8e () ffffff003fefb820 zfs:zap_lockdir+6d () ffffff003fefb8b0 zfs:zap_update+5b () ffffff003fefb930 zfs:zap_increment+9b () ffffff003fefb9b0 zfs:zap_increment_int+68 () ffffff003fefba10 zfs:do_userquota_update+8a () ffffff003fefba70 zfs:dmu_objset_do_userquota_updates+de () ffffff003fefbaf0 zfs:dsl_pool_sync+112 () ffffff003fefbba0 zfs:spa_sync+37b () ffffff003fefbc40 zfs:txg_sync_thread+247 () ffffff003fefbc50 unix:thread_start+8 () Any ideas what this means?

  Read the article

• SNMP based network discovery (switches), device (ports on switches) power management

  - by SaM

  In a enterprise network, what would be the right way to generate a list of switches (SNMP managed) Is it reasonable to ask the organization to supply a list such as this: Switch name IP Address of switch Location SNMP community strings Or are there standard ways to run discovery scans - UDP broadcasts? After having generated a repository such as the above; given a single switch, how to query it for the list of all devices attached to it? Finally, how to selectively power down/power up ports? (remotely - using SNMP) Platform is going to be .NET based (C#) and the library being used is SharpSNMP

  Read the article

• How to enable mysqli extension on redhat?

  - by nuthan

  My php.ini says: Additional .ini files parsed /etc/php53/php.d/curl.ini, /etc/php53/php.d/fileinfo.ini, /etc/php53/php.d/json.ini, /etc/php53/php.d/mysqli.ini, /etc/php53/php.d/mysql.ini, /etc/php53/php.d/pdo_mysql.ini, /etc/php53/php.d/phar.ini, /etc/php53/php.d/zip.ini mysqli.ini is loaded.. But still i get this, PHP Fatal error: Class 'mysqli' not found i tried enabling dynamic loading and initialize php scripts with dl("mysqli.so"); i also tried recompiling the php source: ./configure --with-mysql=/usr/lib64/mysql --with- mysqli=/usr/lib64/mysql/mysql_config even this didn't work. Can anybody help me solve my problem? Red Hat Enterprise Linux Server release 5 (Tikanga). x86_64 GNU/Linux. No access to RHN. Thanks.

  Read the article

• django url matching with Lighttpd fastcgi

  - by 7seb

  I have a problem with url. I can access the djando app home page ( localhost/djangotest/ ) but can't access the admin section ( localhost/djangotest/admin/ ). I can access it using the django server instead of lighttpd. Lighttp conf : fastcgi.server = ( "/djangotest/" => ( "main" => ( "host" => "127.0.0.1", "port" => 3033, "check-local" => "disable", ) ), ) url.rewrite-once = ( "^(/media.*)$" => "$1", "^/favicon\.ico$" => "/media/favicon.ico", "^/djangotest/[^?](.*)$" => "/djangotest/?$1", ) The django url.py is just : (i just uncommented the good lines) : from django.conf.urls.defaults import patterns, include, url from django.contrib import admin admin.autodiscover() urlpatterns = patterns('', url(r'^admin/', include(admin.site.urls)), ) I tried many things but without success ... (no need to link to https://docs.djangoproject.com/en/dev/howto/deployment/fastcgi/ ) lighttpd/1.4.28 Python 2.7.2+ Django 1.3.0

  Read the article

• rpm installation error

  - by JiminyCricket

  im trying to install an RPM compat-db-4.1.25-9 on oracle linux enterprise, since its required to install WebCenter...however the rpm installation is throwing a warning and then not working [root@devsebl downloads]# rpm -i compat-db-4.1.25-9.rpm warning: compat-db-4.1.25-9.rpm: Header V3 DSA signature: NOKEY, key ID 9b3c94f4 [root@devsebl downloads]# rpm -q compat-db-4.1.25-9.rpm package compat-db-4.1.25-9.rpm is not installed any idea what that warning means and why its crashing there? i tried to use Yum, but its not available i guess: [root@devsebl downloads]# yum search compat-db Loaded plugins: security Warning: No matches found for: compat-db No Matches found

  Read the article

• How to modify PATH variable for X11 during log-in?

  - by user1028435

  I originally posted this over at StackOverflow, but someone said it might fit better here. Original question is here: http://stackoverflow.com/questions/10096327/overwriting-print-screen-actions-in-linux-without-administrative-rights. Decided to revise my question, based on what I learned there: Essentially, my problem is that I am working on some lab computers (read: no administrative rights) that, if I log in, I need to change the PATH variable as X11 starts. The reason is that I need to change the PATH variable at this time, as opposed to later, is that the Print Screen command seems to "bind" during login (forgive my bad explanation of this). You can see in the work-around I listed in the previous question, that I can make it work by starting a new X, but I was wondering if it is possible to change upon login. If this seems a poor explanation, you can check out the original link for my context and reasoning behind what I'm doing. Any ideas? Details about Distribution: cat /etc/redhat-release tells me: Red Hat Enterprise Linux Client release 5.8 (Tikanga)

  Read the article

• Certificate Template Missing from "Certificate Template to Issue"

  - by Adam Robinson

  I'm having a problem similar to that posted in this question: Missing Certificate template From certificate to issue The short version is that I've created a duplicate certificate template and I'm trying to add it to my domain CA so that I can issue certificates with it. However, when I go into the Certification Authority MMC and go to "Certificate Templates - New - Certificate Template To Issue", my template is missing (along with quite a number of other templates that are present in the domain). Unlike the previous question, however, my CA is running on Server 2008 R2 Enterprise. Our organization has a single DC and a single CA, so I'm not seeing where there could be propagation delay. Any ideas how to get my template to show so that I can issue certificates?

  Read the article

< Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >