Search Results

Search found 25196 results on 1008 pages for 'hard drive cache'.

Page 225/1008 | < Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >

• change Magento to new server, images of existing product do not shown in frontend

  - by forrest gump

  I have moved a Magento website to a new server to optimize speed. All images appear to be replaced by image placeholders. I tried to set permission for media to 777, when I delete cache media folder and refresh, a new cache folder is created automatically, but only with placeholder images inside. I flushed image cache, reindex in magento backend but still no hope. What should I do now? Somethings might be helpful: . It's fine to create new product with images . Flush cache, only placeholders images are created . tried to use magento-cleanup.php, no hope . tried to remove .htaccess in media folder . the images of products are there in the media folder, just not in cache folder. Magento only looks at the cache folder for image :(

  Read the article

• Algorithm to classify a list of products?

  - by Martin

  I have a list representing products which are more or less the same. For instance, in the list below, they are all Seagate hard drives. Seagate Hard Drive 500Go Seagate Hard Drive 120Go for laptop Seagate Barracuda 7200.12 ST3500418AS 500GB 7200 RPM SATA 3.0Gb/s Hard Drive New and shinny 500Go hard drive from Seagate Seagate Barracuda 7200.12 Seagate FreeAgent Desk 500GB External Hard Drive Silver 7200RPM USB2.0 Retail For a human being, the hard drives 3 and 5 are the same. We could go a little bit further and suppose that the products 1, 3, 4 and 5 are the same and put in other categories the product 2 and 6. We have a huge list of products that I would like to classify. Does anybody have an idea of what would be the best algorithm to do such thing. Any suggestions? I though of a Bayesian classifier but I am not sure if it is the best choice. Any help would be appreciated! Thanks.

  Read the article

• How to safely move where itunes saves music/iphone apps/and meta data to another internal Drive?

  - by GingerLee

  In the past, when I have moved my itunes data from one computer to another, I usually just follow these steps: Copy the contents of two folders: %USERPROFILE%\Music\iTunes %USERPROFILE%\AppData\Roaming\Apple Computer 1) Install iTunes on the new computer, start it and close it (don't let it search for music). 2) Copy all the files in the above folders from old PC to new PC. 3) Start iTunes and authorize the new computer (and deauthorize old one). 4) Before syncing, update all iphone apps to current versions on both my iphone and in itunes. 5) The Sync. The above steps always work for me, and basically Itunes on my new PC works exactly as it did on the old PC. My Question: In the hopes of bybassing the above steps in the future, I would like to just have Itunes use another internal Drive that I use for file storage (e.g. D:/) as the path for the above two directory? Then if I move to new PC again, I could just setup itunes to use the correct path. Is that possible yet with minimal implications? If so how?

  Read the article

• Using the windows api and C++, how could I load an exe from the hard drive and run it in its own thread?

  - by returneax

  For the sake of learning I'm trying to do what the OS does when launching a program ie. parsing a PE file and giving it a thread of execution. If I have two exe's one called foo.exe and the other bar.exe, how could I have foo.exe load the contents of bar.exe into memory then have it execute from there in its own thread? I know how to get it into memory using MapViewOfFile or by simple loading the contents on the hard drive into a buffer. I'm assuming simply copying the contents of bar.exe on disk into its own suspended thread and running it wouldn't work. I am semi-familiar with PE file internals. All help is very much appreciated, of course :)

  Read the article

• Difference between redirecting to a page and coming to the same page after pressing back button

  - by Mac

  Actually i have a page in which i am not using cache by using this code HttpContext.Current.Response.Cache.SetExpires(DateTime.UtcNow.AddDays(-1)); HttpContext.Current.Response.Cache.SetValidUntilExpires(false); HttpContext.Current.Response.Cache.SetRevalidation(HttpCacheRevalidation.AllCaches); HttpContext.Current.Response.Cache.SetCacheability(HttpCacheability.NoCache); HttpContext.Current.Response.Cache.SetNoStore(); now i want to know is there any difference between coming to this page using a proper link or coming back using browser back button or is there any way to detect this.

  Read the article

• I'm having a hard time wrapping my head around handling the Activity Lifecycle...

  - by kefs

  So it seems i've created a fatal flaw and coded an app before understanding/handling rotation/lifecycle events.. Currently, all of my code is in onCreate of each activity. I've read a lot of lifecycle tutorials online, including the official dev guide info, but i'm still having an almost unbelievably hard time trying to wrap my head around the rotation/lifecycle events/methods and when to use them correctly. For example, my app currently has an activity that opens the db, inserts a record, then closes the db.. if i rotate my screen on this activity, the data is re-entered into the db. Using the available lifecycle events (onPause(), onResume(), etc..), how would I prevent this db call from happening again? Would I have to pass a variable through the state saying that the db call has been done, and not to do it again? Thanks in advance..

  Read the article

• How do I restore an Apache configuration after a hard restart?

  - by iPhoneARguy

  I installed Apache on my Ubuntu server, and when it installed, it created a directory ~/Apache/ with directories such as htdocs, logs, cgi-bin, etc. I was then able to create several pages and scripts which I placed into the corresponding directories (~/Apache/htdocs, ~/Apache/cgi-bin), and I was able to serve these files on the web. Unfortunately, my server had an unexpected hard restart, and since then, it seems like the files aren't being served. The server is still up, but when I navigate to the URL, I get a page that says "It works!" instead of what was expected. Does anyone know how I can get Apache to serve from ~/Apache/htdocs again? I tried to RTFM and Google for an answer already but it wasn't very helpful.

  Read the article

• Can Eclipse not hard-code ECLIPSE_HOME when exporting build.xml?

  - by stevex

  I have an Eclipse project that I'm attempting to set up to build both with Eclipse and externally with Ant. It seems like a good way to do this is to have Eclipse generate a build.xml file that I can then use with ant. I'd like to set it up so the build.xml can be regenerated from Eclipse whenever the need arises, which means no hand-editing the build.xml file. But Eclipse writes one entry in there that has a hard-coded path to a directory on my computer, which makes it unsuitable for checking in to a source repository. Specifically it's this entry that's the trouble: <property name="ECLIPSE_HOME" value="D:/Eclipse/Eclipse Galileo (3.5) SR1"/> Is there some way to have Eclipse not output this line, or to make it a relative reference or something that makes sense to check in?

  Read the article

• Is this DVD drive broken? Brand new, i need help convincing

  - by acidzombie24

  I am asking bc i know dell is going to give me a problem. How do i know if my DVD is broken on my laptop? i burnt 4 DL disc and they ALL failed, i called and dell suggested roxio. I used it and burnt 1 disc without error and the 2nd disc with an error. With both apps there were no 'problems' during the burning process only failed on the verification process. Some of these bad disc dont work on other PCs and one locks up windows when i click a specific file. Does that sound like a broken burner to you guys? when i called dell they told me since it can read disc properly 100% of the time and software doesnt fail in the burning process its not a broken drive _. They forward me to software support who demand a fee (i think $100) to help me fix my software. I am annoyed bc i dont want to be on the phone for them to watch me burn a dvd and since i burned it once correctly i dont want to happen to burn correctly again to have them say they solved my problem (doing nothing) and charge me refusing to refund. -edit- The errors i got were 1) the request could not be performed because of an I/O device error 2) Windows locking up when opening 1 specific file 3) Cannot copy : Data error (crc) NOTE: the file that causes the problems are random every disc

  Read the article

• Output caching in HTTP Handler and SetValidUntilExpires

  - by mayor

  I'm using output caching in my custom HTTP handler in the following way: public void ProcessRequest(HttpContext context) { TimeSpan freshness = new TimeSpan(0, 0, 0, 60); context.Response.Cache.SetExpires(DateTime.Now.Add(freshness)); context.Response.Cache.SetMaxAge(freshness); context.Response.Cache.SetCacheability(HttpCacheability.Public); context.Response.Cache.SetValidUntilExpires(true); ... } It works, but the problem is that refreshing the page with F5 leads to page regeneration (instead of cache usage) despite of the last codeline: context.Response.Cache.SetValidUntilExpires(true); Any suggestions?

  Read the article

• Customize your icons in Windows 7 and Vista

  - by Matthew Guay

  Want to change out the icons on your desktop and more?  Personalizing your icons is a great way to make your PC uniquely yours,, and today we show you how to grab unique icons, and default Winnows. to be your own. Change the icon for Computer, Recycle Bin, Network, and your User folder Right-click on the desktop, and select Personalize. Now, click the “Change desktop icons” link on the left sidebar in the Personalization window. The window looks slightly different in Windows Vista, but the link is the same. Select the icon you wish to change, and click the Change Icon button.  In Windows 7, you will also notice a box to choose whether or not to allow themes to change icons, and you can uncheck it if you don’t want themes to change your icon settings. You can select one of the other included icons, or click browse to find the icon you want.  Click Ok when you are finished. Change Folder icons You can easily change the icon on most folders in Windows Vista and 7.  Simply right-click on the folder and select properties. Click the Customize tab, and then click the Change Icon button.  This will open the standard dialog to change your icon, so proceed as normal. This basically just creates a hidden desktop.ini file in the folder containing the following or similar data: [.ShellClassInfo]IconFile=%SystemRoot%\system32\SHELL32.dllIconIndex=20 You could manually create or edit the file if you choose, instead of using the dialogs. Simply create a new text file named desktop.ini with this same information, or edit the existing one.  Change the IconFile line to the location of your icon. If you are pointing to a .ico file you should change the IconIndex line to 0 instead. Note that this isn’t available for all folders, for instance you can’t use this to change the icon for the Windows folder.   In Windows 7, please note that you cannot change the icon of folder inside a library.  So if you are browsing your Documents library and would like to change an icon in that folder, right-click on it and select Open folder location.  Now you can change the icon as above. And if you would like to change a Library’s icon itself, then check out this tutorial: Change Your Windows 7 Library Icons the Easy Way Change the icon of any file type Want to make you files easier to tell apart?  Check out our tutorial on how to simply do this: Change a File Type’s Icon in Windows 7 Change the icon of any Application Shortcut To change the icon of a shortcut on your desktop, start menu, or in Explorer, simply right-click on the icon and select Properties. In the Shortcut tab, click the Change Icon button. Now choose one of the other available icons or click browse to find the icon you want. Change Icons of Running Programs in the Windows 7 taskbar If your computer is running Windows 7, you can customize the icon of any program running in the taskbar!  This only works on applications that are running but not pinned to the taskbar, so if you want to customize a pinned icon you may want to unpin it before customizing it.  But the interesting thing about this trick is that it can customize any icon anything running in the taskbar, including things like Control Panel! Right-click or click and push up to open the jumplist on the icon, and then right-click on the program’s name and select Properties.  Here we are customizing Control Panel, but you can do this on any application icon. Now, click Change Icon as usual. Select an icon you want (We switched the Control Panel icon to the Security Shield), or click Browse to find another icon.  Click Ok when finished, and then close the application window. The next time you open the program (or Control Panel in our example), you will notice your new icon on its taskbar icon. Please note that this only works on applications that are currently running and are not pinned to the taskbar.  Strangely, if the application is pinned to the taskbar, you can still click Properties and change the icon, but the change will not show up. Change the icon on any Drive on your Computer You can easily change the icon on your internal hard drives and portable drives with the free Drive Icon Changer application.  Simply download and unzip the file (link below), and then run the application as administrator by right-clicking on the icon and selecting “Run as administrator”. Now, select the drive that you want to change the icon of, and select your desired icon file. Click Save, and Drive Icon Changer will let you know that the icon has been changed successfully. You will then need to reboot your computer to complete the changes.  Simply click Yes to reboot. Now, our Drive icon is changed from this default image: to a Laptop icon we chose! You can do this to any drive in your computer, or to removable drives such as USB flash drives.  When you change these drives icons, the new icon will appear on any computer you insert the drive into.  Also, if you wish to remove the icon change, simply run the Drive Icon Changer again and remove the icon path. Download Drive Icon Changer This application actually simply creates or edits a hidden Autorun.inf file on the top of your drive.  You can edit or create the file yourself by hand if you’d like; simply include the following information in the file, and save it in the top directory of your drive: [autorun]ICON=[path of your icon] Remove Arrow from shortcut icons Many people don’t like the arrow on the shortcut icon, and there are two easy ways to do this. If you’re running the 32 bit version of Windows Vista or 7, simply use the Vista Shortcut Overlay Remover. If your computer is running the 64 bit version of Windows Vista or 7, use the Ultimate Windows Tweaker instead.  Simply select the Additional Tweaks section, and check the “Remove arrows from Shortcut Icons.” For more info and download links check out this article: Disable Shortcut Icon Arrow Overlay in Windows 7 or Vista Closing: This gives you a lot of ways to customize almost any icon on your computer, so you can make it look just like you want it to.  Stay tuned for more great desktop customization articles from How-to Geek! Similar Articles Productive Geek Tips Change Start Menu to Use Small Icons in Windows 7 or VistaResize Icons Quickly in Windows 7 or Vista ExplorerRoundup: 16 Tweaks to Windows Vista Look & FeelRestore Missing Desktop Icons in Windows 7 or VistaClean Up Past Notification Icons in Windows Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Change DNS servers on the fly with DNS Jumper Live PDF Searches PDF Files and Ebooks Converting Mp4 to Mp3 Easily Use Quick Translator to Translate Text in 50 Languages (Firefox) Get Better Windows Search With UltraSearch Scan News With NY Times Article Skimmer

  Read the article

• Change or Reset Windows Password from a Ubuntu Live CD

  - by Trevor Bekolay

  If you can’t log in even after trying your twelve passwords, or you’ve inherited a computer complete with password-protected profiles, worry not – you don’t have to do a fresh install of Windows. We’ll show you how to change or reset your Windows password from a Ubuntu Live CD. This method works for all of the NT-based version of Windows – anything from Windows 2000 and later, basically. And yes, that includes Windows 7. You’ll need a Ubuntu 9.10 Live CD, or a bootable Ubuntu 9.10 Flash Drive. If you don’t have one, or have forgotten how to boot from the flash drive, check out our article on creating a bootable Ubuntu 9.10 flash drive. The program that lets us manipulate Windows passwords is called chntpw. The steps to install it are different in 32-bit and 64-bit versions of Ubuntu. Installation: 32-bit Open up Synaptic Package Manager by clicking on System at the top of the screen, expanding the Administration section, and clicking on Synaptic Package Manager. chntpw is found in the universe repository. Repositories are a way for Ubuntu to group software together so that users are able to choose if they want to use only completely open source software maintained by Ubuntu developers, or branch out and use software with different licenses and maintainers. To enable software from the universe repository, click on Settings > Repositories in the Synaptic window. Add a checkmark beside the box labeled “Community-maintained Open Source software (universe)” and then click close. When you change the repositories you are selecting software from, you have to reload the list of available software. In the main Synaptic window, click on the Reload button. The software lists will be downloaded. Once downloaded, Synaptic must rebuild its search index. The label over the text field by the Search button will read “Rebuilding search index.” When it reads “Quick search,” type chntpw in the text field. The package will show up in the list. Click on the checkbox near the chntpw name. Click on Mark for Installation. chntpw won’t actually be installed until you apply the changes you’ve made, so click on the Apply button in the Synaptic window now. You will be prompted to accept the changes. Click Apply. The changes should be applied quickly. When they’re done, click Close. chntpw is now installed! You can close Synaptic Package Manager. Skip to the section titled Using chntpw to reset your password. Installation: 64-bit The version of chntpw available in Ubuntu’s universe repository will not work properly on a 64-bit machine. Fortunately, a patched version exists in Debian’s Unstable branch, so let’s download it from there and install it manually. Open Firefox. Whether it’s your preferred browser or not, it’s very readily accessible in the Ubuntu Live CD environment, so it will be the easiest to use. There’s a shortcut to Firefox in the top panel. Navigate to http://packages.debian.org/sid/amd64/chntpw/download and download the latest version of chntpw for 64-bit machines. Note: In most cases it would be best to add the Debian Unstable branch to a package manager, but since the Live CD environment will revert to its original state once you reboot, it’ll be faster to just download the .deb file. Save the .deb file to the default location. You can close Firefox if desired. Open a terminal window by clicking on Applications at the top-left of the screen, expanding the Accessories folder, and clicking on Terminal. In the terminal window, enter the following text, hitting enter after each line: cd Downloadssudo dpkg –i chntpw* chntpw will now be installed. Using chntpw to reset your password Before running chntpw, you will have to mount the hard drive that contains your Windows installation. In most cases, Ubuntu 9.10 makes this simple. Click on Places at the top-left of the screen. If your Windows drive is easily identifiable – usually by its size – then left click on it. If it is not obvious, then click on Computer and check out each hard drive until you find the correct one. The correct hard drive will have the WINDOWS folder in it. When you find it, make a note of the drive’s label that appears in the menu bar of the file browser. If you don’t already have one open, start a terminal window by going to Applications > Accessories > Terminal. In the terminal window, enter the commands cd /medials pressing enter after each line. You should see one or more strings of text appear; one of those strings should correspond with the string that appeared in the title bar of the file browser earlier. Change to that directory by entering the command cd <hard drive label> Since the hard drive label will be very annoying to type in, you can use a shortcut by typing in the first few letters or numbers of the drive label (capitalization matters) and pressing the Tab key. It will automatically complete the rest of the string (if those first few letters or numbers are unique). We want to switch to a certain Windows directory. Enter the command: cd WINDOWS/system32/config/ Again, you can use tab-completion to speed up entering this command. To change or reset the administrator password, enter: sudo chntpw SAM SAM is the file that contains your Windows registry. You will see some text appear, including a list of all of the users on your system. At the bottom of the terminal window, you should see a prompt that begins with “User Edit Menu:” and offers four choices. We recommend that you clear the password to blank (you can always set a new password in Windows once you log in). To do this, enter “1” and then “y” to confirm. If you would like to change the password instead, enter “2”, then your desired password, and finally “y” to confirm. If you would like to reset or change the password of a user other than the administrator, enter: sudo chntpw –u <username> SAM From here, you can follow the same steps as before: enter “1” to reset the password to blank, or “2” to change it to a value you provide. And that’s it! Conclusion chntpw is a very useful utility provided for free by the open source community. It may make you think twice about how secure the Windows login system is, but knowing how to use chntpw can save your tail if your memory fails you two or eight times! Similar Articles Productive Geek Tips Reset Your Ubuntu Password Easily from the Live CDChange Your Forgotten Windows Password with the Linux System Rescue CDHow to Create and Use a Password Reset Disk in Windows Vista & Windows 7Reset Your Forgotten Password the Easy Way Using the Ultimate Boot CD for WindowsHow to install Spotify in Ubuntu 9.10 using Wine TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Add a Custom Title in IE using Spybot or Spyware Blaster When You Need to Hail a Taxi in NYC Live Map of Marine Traffic NoSquint Remembers Site Specific Zoom Levels (Firefox) New Firefox release 3.6.3 fixes 1 Critical bug Dark Side of the Moon (8-bit)

  Read the article

• What to Do When Windows Won’t Boot

  - by Chris Hoffman

  You turn on your computer one day and Windows refuses to boot — what do you do? “Windows won’t boot” is a common symptom with a variety of causes, so you’ll need to perform some troubleshooting. Modern versions of Windows are better at recovering from this sort of thing. Where Windows XP might have stopped in its tracks when faced with this problem, modern versions of Windows will try to automatically run Startup Repair. First Things First Be sure to think about changes you’ve made recently — did you recently install a new hardware driver, connect a new hardware component to your computer, or open your computer’s case and do something? It’s possible the hardware driver is buggy, the new hardware is incompatible, or that you accidentally unplugged something while working inside your computer. The Computer Won’t Power On At All If your computer won’t power on at all, ensure it’s plugged into a power outlet and that the power connector isn’t loose. If it’s a desktop PC, ensure the power switch on the back of its case — on the power supply — is set to the On position. If it still won’t power on at all, it’s possible you disconnected a power cable inside its case. If you haven’t been messing around inside the case, it’s possible the power supply is dead. In this case, you’ll have to get your computer’s hardware fixed or get a new computer. Be sure to check your computer monitor — if your computer seems to power on but your screen stays black, ensure your monitor is powered on and that the cable connecting it to your computer’s case is plugged in securely at both ends. The Computer Powers On And Says No Bootable Device If your computer is powering on but you get a black screen that says something like “no bootable device” or another sort of “disk error” message, your computer can’t seem to boot from the hard drive that Windows was installed on. Enter your computer’s BIOS or UEFI firmware setup screen and check its boot order setting, ensuring that it’s set to boot from its hard drive. If the hard drive doesn’t appear in the list at all, it’s possible your hard drive has failed and can no longer be booted from. In this case, you may want to insert Windows installation or recovery media and run the Startup Repair operation. This will attempt to make Windows bootable again. For example, if something overwrote your Windows drive’s boot sector, this will repair the boot sector. If the recovery environment won’t load or doesn’t see your hard drive, you likely have a hardware problem. Be sure to check your BIOS or UEFI’s boot order first if the recovery environment won’t load. You can also attempt to manually fix Windows boot loader problems using the fixmbr and fixboot commands. Modern versions of Windows should be able to fix this problem for you with the Startup Repair wizard, so you shouldn’t actually have to run these commands yourself. Windows Freezes or Crashes During Boot If Windows seems to start booting but fails partway through, you may be facing either a software or hardware problem. If it’s a software problem, you may be able to fix it by performing a Startup Repair operation. If you can’t do this from the boot menu, insert a Windows installation disc or recovery disk and use the startup repair tool from there. If this doesn’t help at all, you may want to reinstall Windows or perform a Refresh or Reset on Windows 8. If the computer encounters errors while attempting to perform startup repair or reinstall Windows, or the reinstall process works properly and you encounter the same errors afterwards, you likely have a hardware problem. Windows Starts and Blue Screens or Freezes If Windows crashes or blue-screens on you every time it boots, you may be facing a hardware or software problem. For example, malware or a buggy driver may be loading at boot and causing the crash, or your computer’s hardware may be malfunctioning. To test this, boot your Windows computer in safe mode. In safe mode, Windows won’t load typical hardware drivers or any software that starts automatically at startup. If the computer is stable in safe mode, try uninstalling any recently installed hardware drivers, performing a system restore, and scanning for malware. If you’re lucky, one of these steps may fix your software problem and allow you to boot Windows normally. If your problem isn’t fixed, try reinstalling Windows or performing a Refresh or Reset on Windows 8. This will reset your computer back to its clean, factory-default state. If you’re still experiencing crashes, your computer likely has a hardware problem. Recover Files When Windows Won’t Boot If you have important files that will be lost and want to back them up before reinstalling Windows, you can use a Windows installer disc or Linux live media to recover the files. These run entirely from a CD, DVD, or USB drive and allow you to copy your files to another external media, such as another USB stick or an external hard drive. If you’re incapable of booting a Windows installer disc or Linux live CD, you may need to go into your BIOS or UEFI and change the boot order setting. If even this doesn’t work — or if you can boot from the devices and your computer freezes or you can’t access your hard drive — you likely have a hardware problem. You can try pulling the computer’s hard drive, inserting it into another computer, and recovering your files that way. Following these steps should fix the vast majority of Windows boot issues — at least the ones that are actually fixable. The dark cloud that always hangs over such issues is the possibility that the hard drive or another component in the computer may be failing. Image Credit: Karl-Ludwig G. Poggemann on Flickr, Tzuhsun Hsu on Flickr     

  Read the article

• How to flush DNS cache in Windows Mobile programmatically?

  - by Bounded

  Hello, My windows mobile application (written in C# with the compact framework) needs to know if a particular machine is active or not. To achieve this goal, I thought to use a ping mechanism. I tried to use the Ping class implemented in the opennetcf framework (the System.Net.NetworkInformation.Ping class for the .NET Framework is not part of the compact framework). Because I give to the Ping.Send function a host name, it first tries to resolve this host name and to retrieve an IP address. But i observe the following problem : If the first dns resolution fails (because the network is down at this moment), and if the application tries immediately again to send the ping, it fails too, even if the network is note down anymore. I check with a famous network protocol analyzer and i saw that only the requests concerning the first dns resolution are sent. The requests concerning the dns resolution of the second ping are not sent. Why is the second dns request not sent ? Is there any dns cache mechanism on such Windows Mobile devices ? If yes, can this mechanism beeing flushed programmatically ? EDIT : I gave up finding a solution to this DNS flush. I chose to ping an IP adress instead of a name machine. The problem of pinging an hard coded adress IP is that we have to be 100% sure that this IP will not change. The gateway IP can be used because it's always reachable (if it does not, it means the network is down).

  Read the article

• Is NSManagedObjectContext autosaved or am I looking at NSFetchedResultsController's cache?

  - by Andreas

  I'm developing an iPhone app where I use a NSFetchedResultsController in the main table view controller. I create it like this in the viewDidload of the main table view controller: NSSortDescriptor *sortDescriptorDate = [[NSSortDescriptor alloc] initWithKey:@"date" ascending:YES]; NSSortDescriptor *sortDescriptorTime = [[NSSortDescriptor alloc] initWithKey:@"start" ascending:YES]; NSArray *sortDescriptors = [[NSArray alloc] initWithObjects:sortDescriptorDate,sortDescriptorTime, nil]; [fetchRequest setSortDescriptors:sortDescriptors]; [sortDescriptorDate release]; [sortDescriptorTime release]; [sortDescriptors release]; controller = [[NSFetchedResultsController alloc] initWithFetchRequest:fetchRequest managedObjectContext:context sectionNameKeyPath:@"date" cacheName:nil]; [fetchRequest release]; NSError *error; BOOL success = [controller performFetch:&error]; Then, in a subsequent view, I create a new object on the context: TestObject *testObject = [NSEntityDescription insertNewObjectForEntityForName:@"TestObject" inManagedObjectContext:context]; The TestObject has several related object which I create in the same way and add to the testObject using the provided add...Objects methods. Then, if before saving the context, I press cancel and go back to the main table view, nothing is shown as expected. However, if I restart the app, the object I created on the context shows in the main table view. How come? At first, I thought it was because the NSFetchedResultsController was reading from the cache, but as you can see I set this to nil just to test. Also, [context hasChanges] returns true after I restart. What am I missing here?

  Read the article

• How do i programmatically access the face cache in Windows Live Photo Gallery?

  - by acorderob

  I'm not talking about the "people tags" embeded in the XMP packets of JPEGs. I'm talking about the face database used to recognize new faces. I want to add to my program the option to recognize faces using the already trained database of WLPG. I managed to use the API (a type library dll) to detect faces, but to recognize them it needs an Exemplar Cache object that is not available in the same API. I could create my own object, but i want to use the already existing one to avoid duplicate training for the user. I know the database is in C:\Users\\AppData\Local\Microsoft\Windows Live Photo Gallery and that it is in an SQL Server Compact format. I tried to open the database with Visual Studio 2010, but it says that it is in an older version (pre-3.5) and needs to be upgraded. I don't want to change the database, just read it. I don't know how the WPLG reads it since apparently i don't have the correct OLEDB provider version. I would also prefer to read it without accesing the database directly but i don't see any DLL that exports that functionality. BTW, i'm using Delphi 2010. Any ideas?

  Read the article

• Ruby On Rails with HTML5 offline apps - Firefox does not cache the application.manifest but Safari does

  - by hoitomt

  I'm working off of this Railscast tutorial: episode 247 I’m up to this point in the tutorial: added the rack-offline gem, added the application.manifest route, and added a reference to the manifest in the html tag. Right before it starts talking about problems with caching. Safari works as intended – When the server is running the page is served. From the server logs I can see that Safari is making a single request to the server every time for the items page. When I turn off the server the page displays as well, even after shutting down the browser and restarting. It appears to be pulling from the application.manifest (cache manifest). Firefox does not work as intended – When accessing the page for the first time, Firefox lets me know that the web page wants to store something locally, I allow. After clicking on allow, Firefox makes 5 requests to the server for the page (from the server log). The hash is different in every request. Is it is possible that the changing hash is triggering Firefox to keep trying to get the new manifest until it reaches some maximum (5 attempts)? Then, after the server is stopped, Firefox will not show the page at all. It looks like it isn’t caching the application.manifest. Firefox also gives you a way to see what sites are storing stuff locally by going to Tools/Options/Advanced/Network (Firefox/Preferences/Advanced/Network on Apple). I see localhost there but the size is 0 bytes. So for some reason, Firefox is not downloading my application.manifest along with the files

  Read the article

• Vista install works on one computer, but bluescreens another (on which Vista is known to work)

  - by Ken

  I hope my explanations make some sense -- please ask for clarification if they don't. I had a computer running Windows Vista (Ultimate, 64-bit). All was well! Then one day there was a nasty power surge at the office, and it died. (We didn't have surge protectors at the office, unfortunately. I assumed our lines were conditioned elsewhere, or was not an issue here. Oops.) After some testing, it was determined that the PSU, motherboard, and RAM were bad. While waiting for new hardware to arrive, I put my hard disk in a spare PC which had identical parts (mobo/CPU/RAM/PSU/video). Everything worked perfectly. The only way I could even tell it wasn't my computer is because Vista asked to re-activate itself with the new hardware, which worked fine, too. So the hard disk seems OK. Then the new parts arrived. The old motherboard model is no longer manufactured, so it's a new one with the same CPU/RAM/videocard/etc. slots. The PSU is also new, while the RAM I'm using is from the spare PC mentioned above. When I put it together and tried booting with my old hard disk, it starts to boot Windows, and then (fairly early in the process) gives a bluescreen and immediately reboots (so I can't see whatever the bluescreen is trying to tell me). I tried "safe mode", which also bluescreened. I tried booting the Vista DVD and running the repair utility, which found a Vista install, confirmed that it would not boot, and, eventually, declared that it was unable to repair it. I installed Vista fresh on a new hard disk, with the new mobo/etc., and it works perfectly. (That's what I'm running now.) I've also booted a Linux CD here, which ran great, and I've run Memtest86+ for a while, which found no errors. So all the hardware apart from the old hard disk seems OK, too. I don't think the problem is with my old Vista hard disk, since I used that with another mobo/CPU just fine. I don't think it's any other part of the new hardware, since I'm able to use it (and test it) with no trouble. It's just the combination of my old Vista install plus the new PC hardware that's not happy. I can get my data off my old hard disk and onto my new hard disk, and reinstall my apps, but it would be nice if I could fix things so I could continue to use my old hard disk as before. The latest hypothesis I've heard is that Vista had trouble with the new hardware (i.e., motherboard), but we have no idea what to do about that (except Safe Mode, which didn't work). Suggestions? Hypotheses for what's not right about this combination of Vista install and motherboard? Thanks!

  Read the article

• What is causing random hard freezes on my system? Kaspersky?

  - by Christian Ivicevic

  The last few weeks I experienced a new strange behavior of my computer. Sometimes Windows 7 just freezes with no real reason at all. While listening to music for example the playback hangs and you can hear a very nasty sound. Neither mouse nor keyboard input is handled and everything is just stuck. Using Ubuntu this does not happen, so I think it is just a matter of driver issues or a Windows 7 bug. Furthermore I am really suspicious about Kaspersky (Internet Security 11) and so I let it perform a complete virus scan while no other app is running. At about 50% it happened again and I needed to restart the computer by holding the power button the bad way... A really weird thing is that playing Skyrim this happened once, however music playback did not stop. Only the framerate dropped to 0 and sometimes for a few seconds I am able to move. Therefore I am really confused as furthermore no bluescreen pops up. Memtest told me that everything seems to be alright... Can anyone explain me which data you need about my hardware and software (and which tools tools to use to gather the informatik) to be able to provide any help on my problem?

  Read the article

• Recover lost NTFS partition on SSD

  - by Emil

  Hello, About 2 month ago I upgraded my Dell Latitude E6500 laptop with a Corsair Force F120 SSD drive. Everything worked well until about a week or so back. I started the computer and was faced with a beep and a message saying "No boot sector on Internal HDD (IRRT). No bootable devices". Since I figured that the boot sector had somehow got corrupt I tried booting from the Windows 7 dvd in order to repair the boot sector. But the Windows 7 installation program only found a blank drive with 111GB of unallocated space. I panicked and brought the drive with me to work to let a colleague have a look at it. We made a disk image of the entire drive and ran the drive through Testdisk in Linux. Testdisk did not find any partitions. It appears that the drive has been completely erased... What has happened? What is causing this behavior on an SSD?

  Read the article

• How to remove raid 5 array of 5 SAS and use only use one SAS at a time without writing any thing to disc for recovery

  - by murtaza hamid

  I have HP server ML370 g5 with 8 SAS, c drive 1 72 gb raid 0, d drive 2 72 gb raid 0, f drive 5 146 gb raid 5. 2 of 5 sas drive has got bad sectors and raid 5 is showing status failed. now i want to remove all this 5 SAS and put 1 by 1 in any of the bay to make its image for data recovery purpose without writing anything to the drive. how should i proceed. i also want to keep drive c and d intact. also is it possible if i put all this 5 drives in the bay with the same sequense will it recognise the raid 5 array ( i read some where its smart controller..just curious) many thanks in advance.

  Read the article

• How do I send traffic from my Mac's wifi to my VPN client?

  - by Heath Borders

  I need to connect my Android to a Juniper VPN. Unfortunately, Juniper doesn't support Android on our VPN version. We've already put in a feature request for it, but we have no idea how long it will take to be complete. Right now, I connect to the Juniper VPN with a Juniper Mac OSX VPN client that uses Java to install kernel extensions to start and stop the VPN. Thus, I can't use the Network panel in System Preferences to create a VPN device, which means it won't show up in the 'Sharing' panel's Internet Sharing Share your connection from: menu, as suggested here. I used newproc.d to see what /usr/libexec/InternetSharing did when it ran, and it runs the following processes: 2013 Nov 1 00:26:54 5565 <1> 64b /usr/libexec/launchdadd 2013 Nov 1 00:26:55 5566 <1> 64b /usr/libexec/InternetSharing 2013 Nov 1 00:26:56 5568 <5566> 64b natpmpd -d -y bridge100 en0 2013 Nov 1 00:26:56 5569 <1> 64b /usr/libexec/pfd -d 2013 Nov 1 00:26:56 5567 <5566> 64b bootpd -d -P My Juniper VPN client creates the following devices (output of ifconfig): jnc0: flags=841<UP,RUNNING,SIMPLEX> mtu 1400 inet 10.61.9.61 netmask 0xffffffff open (pid 920) jnc1: flags=841<UP,RUNNING,SIMPLEX> mtu 1450 closed So, it seems like I should just be able to do this and have everything work: sudo killall -9 natpmpd sudo /usr/libexec/natpmpd -y bridge100 jnc0 My android connected fine and could hit public internet sites, but it couldn't hit private VPN sites. I assume this is because I need to change the routes that /usr/libexec/InternetSharing sets up. This is the output from sudo pfctl -s all before starting Internet Sharing: No ALTQ support in kernel ALTQ related functions disabled TRANSLATION RULES: nat-anchor "com.apple/*" all rdr-anchor "com.apple/*" all FILTER RULES: scrub-anchor "com.apple/*" all fragment reassemble anchor "com.apple/*" all DUMMYNET RULES: dummynet-anchor "com.apple/*" all INFO: Status: Disabled for 0 days 00:11:02 Debug: Urgent State Table Total Rate current entries 0 searches 22875 34.6/s inserts 1558 2.4/s removals 1558 2.4/s Counters match 2005 3.0/s bad-offset 0 0.0/s fragment 0 0.0/s short 0 0.0/s normalize 0 0.0/s memory 0 0.0/s bad-timestamp 0 0.0/s congestion 0 0.0/s ip-option 12 0.0/s proto-cksum 0 0.0/s state-mismatch 1 0.0/s state-insert 0 0.0/s state-limit 0 0.0/s src-limit 0 0.0/s synproxy 0 0.0/s dummynet 0 0.0/s TIMEOUTS: tcp.first 120s tcp.opening 30s tcp.established 86400s tcp.closing 900s tcp.finwait 45s tcp.closed 90s tcp.tsdiff 60s udp.first 60s udp.single 30s udp.multiple 120s icmp.first 20s icmp.error 10s grev1.first 120s grev1.initiating 30s grev1.estblished 1800s esp.first 120s esp.estblished 900s other.first 60s other.single 30s other.multiple 120s frag 30s interval 10s adaptive.start 6000 states adaptive.end 12000 states src.track 0s LIMITS: states hard limit 10000 app-states hard limit 10000 src-nodes hard limit 10000 frags hard limit 5000 tables hard limit 1000 table-entries hard limit 200000 OS FINGERPRINTS: 696 fingerprints loaded This is the output from sudo pfctl -s all after starting Internet Sharing: No ALTQ support in kernel ALTQ related functions disabled TRANSLATION RULES: nat-anchor "com.apple/*" all nat-anchor "com.apple.internet-sharing" all rdr-anchor "com.apple/*" all rdr-anchor "com.apple.internet-sharing" all FILTER RULES: scrub-anchor "com.apple/*" all fragment reassemble scrub-anchor "com.apple.internet-sharing" all fragment reassemble anchor "com.apple/*" all anchor "com.apple.internet-sharing" all DUMMYNET RULES: dummynet-anchor "com.apple/*" all STATES: ALL tcp 10.0.1.32:50593 -> 74.125.225.113:443 SYN_SENT:CLOSED ALL udp 10.0.1.32:61534 -> 10.0.1.1:53 SINGLE:NO_TRAFFIC ALL udp 10.0.1.32:55433 -> 10.0.1.1:53 SINGLE:NO_TRAFFIC ALL udp 10.0.1.32:64041 -> 10.0.1.1:53 SINGLE:NO_TRAFFIC ALL tcp 10.0.1.32:50619 -> 74.125.225.131:443 SYN_SENT:CLOSED INFO: Status: Enabled for 0 days 00:00:01 Debug: Urgent State Table Total Rate current entries 5 searches 22886 22886.0/s inserts 1563 1563.0/s removals 1558 1558.0/s Counters match 2010 2010.0/s bad-offset 0 0.0/s fragment 0 0.0/s short 0 0.0/s normalize 0 0.0/s memory 0 0.0/s bad-timestamp 0 0.0/s congestion 0 0.0/s ip-option 12 12.0/s proto-cksum 0 0.0/s state-mismatch 1 1.0/s state-insert 0 0.0/s state-limit 0 0.0/s src-limit 0 0.0/s synproxy 0 0.0/s dummynet 0 0.0/s TIMEOUTS: tcp.first 120s tcp.opening 30s tcp.established 86400s tcp.closing 900s tcp.finwait 45s tcp.closed 90s tcp.tsdiff 60s udp.first 60s udp.single 30s udp.multiple 120s icmp.first 20s icmp.error 10s grev1.first 120s grev1.initiating 30s grev1.estblished 1800s esp.first 120s esp.estblished 900s other.first 60s other.single 30s other.multiple 120s frag 30s interval 10s adaptive.start 6000 states adaptive.end 12000 states src.track 0s LIMITS: states hard limit 10000 app-states hard limit 10000 src-nodes hard limit 10000 frags hard limit 5000 tables hard limit 1000 table-entries hard limit 200000 TABLES: OS FINGERPRINTS: 696 fingerprints loaded It looks like I need to change the pf settings that /usr/libexec/InternetSharing set up, but I have no idea how to do that.

  Read the article

• MacBook Pro 15in High-res hard to read. What setting should I change?

  - by orokusaki

  I just bought a new MacBook Pro with the high-res screen (1680x1050), but I noticed that all text is so small that to read it my face has to be like 18 inches away. When I adjusted the resolution to be the next sizes down (1440 x 852, and 1440 x 852 stretched), as well as all the other smaller sizes it made everything look blurry (similarly to when you use Command + Scroll to zoom in, how the text is really soft on the edges, and difficult to read). Is there a setting somewhere that I'm missing, or another resolution settings area that I can use. I feel like this 2800 dollar notebook may be only good for movie watching otherwise. Thanks in advance.

  Read the article

• Ubuntu only boots with USB plugged in

  - by Ben

  I'm new to the Linux world so please bear with me! :-) I installed Ubuntu via USB drive onto my hard drive. If I boot the PC without the usb drive I used, Ubuntu will not load. After booting I can unplug without any consequences. I looked on the hard drive and there is a boot folder. On the USB drive, this is the tree contents: /media/disk$ tree . |-- adtext.cfg |-- boot.cat |-- f10.txt |-- f1.txt |-- f2.txt |-- f3.txt |-- f4.txt |-- f5.txt |-- f6.txt |-- f7.txt |-- f8.txt |-- f9.txt |-- initrd.gz |-- isolinux.bin |-- isolinux.cfg |-- ldlinux.sys |-- linux |-- menu.c32 |-- menu.cfg |-- po4a.cfg |-- prompt.cfg |-- splash.png |-- stdmenu.cfg |-- syslinux.cfg |-- text.cfg |-- ubnfilel.txt |-- ubnpathl.txt `-- vesamenu.c32 Am I correct in my assumption that the boot aspect is associated to the USB drive? If so, how do I get it to boot without the USB? I'm guessing copying into some location and modifying grub?

  Read the article

• How do I make a VMDK format virtual hard drive from a physical partition on a disk?

  - by Ahmad

  I have a 320 GB HDD, which actually only has an 80 GB NTFS format partition which was being used by a Windows 7 system ... I want to create a VMDK format clone of this partition, so that I can use it with VMware .. However, tradition VMDK creation programs normally make a VMDK for an entire disk, whereas I just want to make a VMDK for the one 80 GB partition ... This is important because the other 240 GB on the physical source HDD is just unallocated area, and including that in a VMDK file is just a plain waste of space .. So how to make a VMDK file for a specific partition ? Any tool available for this ?

  Read the article

< Previous Page | 221 222 223 224 225 226 227 228 229 230 231 232  | Next Page >