Search Results

Search found 8782 results on 352 pages for 'krishnadas pc'.

Page 226/352 | < Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >

• RDP for High DPI Monitors?

  - by Joey

  A client is having some problems with their laptop. They use RDP to remote into their work PC, but the laptop they are using is a small 13" Sony Vaio laptop, but with 1920x1080 resolution. Everything is pretty small on the laptop anyway, but the problem is much worse after connecting with RDP, where everything is almost unreadable. I have done the obvious with changing the resolution on the server, the RDP size, forced scaling on the terminal server etc, but nothing has worked. Something else which I would normally do is change the laptop resolution to something a little lower, but the laptop only has 2 resolution settings, the big one, and a 1024x768 (wrong ratio). Any ideas?

  Read the article

• Office suite for eMAC

  - by Adam Pierce

  I have been given 10 old eMAC computers to donate to a local primary school. I am a PC person but I have volunteered to set these up with some kind of office suite. The specs are: 700MHz G4 640MB RAM (should be enough for anyone!) OS-X 10.3 40GB hard disc with 30GB free space I'd like a recommendataion for an office suite that will work on these old boxes. I have tried Open Office, both the latest version and 2.4.3 for PPC with no luck. Yes, I do have X11 installed.

  Read the article

• Ubuntu Wireless card not found

  - by user32121

  Hello all, I'm trying to setup Ubuntu on an old PC. I ran the following command, lspci, in order to get info on the wireless card installed. 00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03) Does anyone know where I can get drivers for this card/chip? And also, how to install (I'm rather new to linux). Also, I'm sure the card is working because I just formatted over xp, and everything was working well. Thanks in advanced!

  Read the article

• Install Windows 8 64-bit over the top of Windows 8 32-bit

  - by Andrew Gee

  I currently have Windows 8 32-bit installed from MSDN (I didn't realise at the time that my processor supports 64-bit). I understand that you can't upgrade within Windows 32-bit to 64-bit directly from the ISO. I have burned the ISO to a DVD, and have attempted booting from this drive. The problem I am encountering: The operating system couldn't be loaded because a required file is missing or contains errors. File: CI.dll Error code: 0xc0000221 You'll need to use the recovery tools on your installation media. If you don't have any installation media (like a disc or USB device), contact your system administrator or PC manufacturer. Additional info: Computer: HP Pavillion m9280.uk-a Processor: AMD Phenom 9600 Quad-Core RAM: 3 1GB sticks Thanks in advance!

  Read the article

• Why does text look so Horrible in my HD monitor???

  - by Laura

  I just bought a 1080p 22" Samsung HD monitor (connected via HDMI) and the picture and video quality is great but the text quality is absolutely horrible. Even as I type now all the text in this text box as well as in the browser toolbar and start menu, etc looks weird - like it all has a white outline around it that makes it jagged and hard to read. It hurts my eyes just to look at it. I am running my PC in the suggested native resolution of 1920 by 1080, so what's the problem? Is this one of the unavoidable downsides of using a HD monitor? Is there a solution to the problem?

  Read the article

• How to quickly switch monitors on multi-monitor setup?

  - by Saxtus

  At my desktop PC, I have 3 displays hooked up on my Palit GeForce GTX 480 to extend my desktop: DVI: Samsung SyncMaster T220 (22" 16:10, 1680x1050, as my main) DVI: Samsung SyncMaster 940BF (19" 4:3, 1280x1024) HDMI: Sony Bravia KDL-32D3000 (32" 16:9, 1360x768) As expected, the GFX card can only utilize 2 of the displays at any given time, so I have to manually switch using Windows' "Display Properties" dialog, each time I want to switch between them. I've tried UltraMon, DisplayFusion and PowerStrip (so please don't refer me to a question where those are given as solutions) but they are unable to switch monitors. Instead they can only change display resolutions and settings on the existing active monitors, with specially weird results when I've saved the monitor states and then tried to switch monitors using the saved states! Any idea on how to bypass the awful "Display Properties" dialog and it's "confirm your change" timer?

  Read the article

• How can I disable Ctrl+Shift+Arrow from causing my screen to flip?

  - by nizzle

  Windows 7 Home Premium, Catalyst Control Center. Without any apparent reason, after booting my PC, I got this little balloon "HD 4600 Drivers updated". I did not install any new cards or drivers or anything. But now, when I try to select an entire word by pressing Ctrl + Shift + ? / ? my screen flips left to right and upside down. Where can I disable this annoying shortcut? OR Any other way of selecting the entire word? There is no option for this in Catalyst Control Center.

  Read the article

• Hot video card in server

  - by DougN

  Not sure if this belongs here or Superuser (I looked at Superuser -- suspect there are more hardware gurus here). I have a server that sits in a cabinet. It's connected to a small screen that is normally off. However, the video card is running at about 210 F all the time. The rest of the PC is pretty cool (getting temps from SpeedFan). Any thoughts on a way to quiet/calm/cool the video card since it's never really doing anything anyway? I'm usually logged out on the server, and no screen saver defined. Windows is already set to turn off the screen for power saving at 5 minutes.

  Read the article

• What are the parental controls within Windows 8 and how do I use them?

  - by KronoS

  I've got some little ones that I want to be able to use my PC, BUT I don't want them using my account since it's an admin account. I've created a user account for them without admin privileges and now I'm looking to see if there is a way to do the following: Prevent them from downloading/purchasing Metro apps Limit amount of time on Computer Limit time of day they can access Limit internet browsing based on age Prevent them from installing desktop applications Any other parental controls that I can set I'm looking for a good exhaustive overview of the parental controls found within Windows 8 and a brief synopsis on how to use those tools.

  Read the article

• I need a few minutes of dedicated server a week, but not for hosting, just to convert ogg etc.

  - by talkingnews

  I'm completely happy with my webhosting, it's just that I need to do one little thing they won't allow, and that's run an instance of Sox to convert about 30 mp3s to ogg files, in various directories, a couple of times a week, to be done automatically in response to the detection of the upload of an mp3. Probably looking at a minute of server time over the whole week. I've had unhelpful suggestions on other forums like "why not leave your home PC on 24 hours a day and then use all your isp bandwidth to do this", which doesn't work for me. I know that I can host files on, say, Amazon S3, but is there something similar for my needs? All it would need to do would be: wget/ftp the mp3 files, convert them to ogg, ftp the files back to my hosting. Of course, all this wouldn't be needed if there was such a thing as a compiled binary of Sox (or any mp3ogg converter) for Centos which I could upload without needing root access, but I've given up asking that one, but always open to suggestions!

  Read the article

• System Center Configuration Manager 2007 - Debugging Client Installs

  - by Dayton Brown

  Hi All: Having an issue installing the CCMsetup client on desktops. The CCMSetup makes it to the PC, files are there, it gets added to the services for automatic start, it starts, but quits almost instantly. Logs on the desktop show a entry like this. <![LOG[Failed to successfully complete HTTP request. (StatusCode at WinHttpQueryHeaders: 404)]LOG]!><time="14:28:51.183+240" date="06-11-2009" component="ccmsetup" context="" type="3" thread="2388" file="ccmsetup.cpp:5808"> What am I missing? EDIT: Firewall is off on both client and server.

  Read the article

• Force Direct3D anti-aliasing in a Direct3D game?

  - by James McLaughlin

  Some old games look really jagged nowadays on large displays without any anti-aliasing, but don't have any option built-in to the game to enable it. On a PC with an NVIDIA graphics card, it's possible to force anti-aliasing in the NVIDIA control panel which can really improve this. But I'm playing the game in Parallels on a Mac, and although the Mac has an NVIDIA graphics card, it's Parallels' emulated card that Windows sees and so obviously there's no NVIDIA control panel. Is there some generic way I can force anti-aliasing for a Direct3D game without using the NVIDIA control panel?

  Read the article

• Is there any software or hardware which lets you stop, slow down, speed up or even reverse time?

  - by tjrobinson

  Obviously I'm talking about time in terms of the PC clock rather than real time. We were testing an application we've developed at work by setting the clock forward and back to simulate different scenarios and I started thinking how useful it would be if you could adjust the rate(?) of the system clock with finer control. So you could make a minute pass in a second or a day pass in 30 seconds and watch how the program you're developing copes with changes in date and time. I'd be interested to hear if anyone knows of any software or hardware which can let you do some or all of the above.

  Read the article

• Setup dhcpd without gateway on purpose

  - by MBober

  I have an XP machine with two network interfaces. One is connected to my company's network (and the Internet). The other is a very local network which connects some hardware with my PC. Both the hardware and my XP machine's second network interface obtain configuration from a dhcpd running on Ubuntu in a virtual machine on my XP machine. I entered some dummy gateway in /etc/dhcp3/dhcpd.conf like 192.168.3.1 which does not match any existing device just to get dhcpd started. The problem is that my XP machine now tries to route Internet traffic through 192.168.3.1 in most of the cases which, of course, results in an error. Is there any way to set up dhcpd in a way that the clients know that there is no gateway in this network? By the way: setting the gateway manually in XP is off the table because this needs administrator privileges which I don't have.

  Read the article

• Hybrid drive not booting faster than a normal HD

  - by Nigel Trotter

  I have used Windows 7 to create an image of my existing standard 160GB HD and copied this image back to a bigger 500GB Seagate hybrid drive. After copying the image to the hybrid I had to resize the partition, which was fine but after rebooting a few times to "teach" the hybrid, I have no increase in boot speed. It still takes 20-25 seconds to close down and then over a minute to start up. Is this something to do with the way the image lays itself on the drive indiscriminately? Do I need to load the OS on the drive from scratch to get the benefits? My PC with an i5 processor, is using AHCI mode.

  Read the article

• Windows XP runs New Hardware Wizard for usb keyboard and mouse, can't find drivers

  - by Randy Orrison

  I have a PC that up until a couple days ago was working fine. I moved it from one site to another and now when I plug in the USB mouse or keyboard (the same ones that were working previously) XP brings up the New Hardware Wizard. Going through it, the correct keyboard and mouse are identified, but XP can't find the drivers. I've tried manually searching for the driver (using the Have Disk option) - the first file it's looking for is in the c:\i386 directory, but that installs a generic HID mouse device; the system then runs the hardware wizard for a new "unknown" device. The system was SP2, I have installed SP3 in hopes that would help, and I've also downloaded and installed the mouse drivers from Dell's site (there are no specific drivers for the keyboard), with no change. Before I completely reinstall XP, is there anything else I should try?

  Read the article

• Linux and GEForge 8400 dual monitor

  - by Andrea Polci

  I'm trying to install a linux distribution on my PC. I have a GEForce 8400 GS with two connected monitors. I tried with fedora 12 and ubuntu 9.1 (both 64 and 32 bit) and the live cd cannot boot properly. I don't get a visible error on ubuntu, it simply hang up during the boot. With fedora I get this erro: [drm] Modeset on unsupported output type [drm] Table 0x0000 not found for 1/1 using first I tried to disconnect one of the two monitor and was able to install on my HD and boot from there, but if I try to connect the second monitor again I cannot boot. Have I to install something else? (a driver for my video card for example).

  Read the article

• RAID0 PROBLEM WITH A SONY SPORTING A NEW HDD

  - by redrock

  Sony Windows 7 PC. Originally had 2 x 300Gb HDD. One HDD completely pancaked so have replaced with a new 500Gb HDD. When both drives are connected the 300GB doesn't appear to be recognised as a 300Gb HDD as a seperate entity. BIOS sees it but the operating system only sees a total of 465GB of HD space. When both disks are attached unde disk management it shows one 465Gb as RAID 0 and the new drive as STxxxxxx 465Gb. My question I guess is what should I see in total HDD space and is this configured correctly as I thought I would see 2 seperate drives 1x500Gb and 1x300Gb. My customer insisted that prior to the HDD crash he saw 2 drives both registering as 300Gb (a c: and d: drive).

  Read the article

• Nginx Forward SSL for single site

  - by Will.brown

  I have a nginx server setup and it works fine for http however i would like to bypass the proxy for https connection. I want it so that when someone goes to my ip https:// ip1 (Nginx server) it bypasses ngix and forwards all traffic to https:// ip2(webserver) i do not need ngix to do this for any ssl website just one particular website. SO Client to https:// ip1 to https:/ /ip2 to https:// ip1 to client pc I just want the nginx to not intercept the connection and forward it on and on return forward the connection to client Im guessing i do this by nat mascarade buy not exactly sure how to do it and if i will need to tell nginx to ignore ssl aswell can someone help me please this has gone me stuck

  Read the article

• No network adapter drivers after Windows re-install

  - by Arno

  This is a pretty basic question. I got a PC (Packard Bell Easynote TK11-BZ-010BE) that had linux on it, so I thought, just delete the partition and its alright. Well, it wasn't. I went into grub recovery and couldn't do anything, so I re-installed windows again. Now the problem is that everything works expect my network adapter. When I go to device manager, I get that there aren't any driver's for it installed. But without internet, I can't install the so called driver finders. How should I solve this?

  Read the article

• Domain Outlook user is asked for password every time despite checking the 'remember password' button

  - by MrVimes

  We have a windows 2003 domain. All users have roaming profiles. We have a couple of users who, when they log into outlook, are asked for their password every time, despite selecting the 'remember my password' option. Our email is externally hosted exchange email. I've tried several fixes found on google such as deleting 'protect' folder in the user's profile, and deleting protect key in the registry but none work. I tried storing the password in windows' password/credentials manager, didn't work. It happens on any PC the users log into so it's not a machine specific problem. Any ideas? OS is Windows XP pro. Outlook is 2007.

  Read the article

• Turtle Beach Headset Chat Volume Wheel on Windows

  - by Todd Freed

  I have this headset http://www.turtlebeach.com/product-detail/headsets-legacy/ear-force-x11/235 I am using it with a Windows 8.1 PC using digital audio out on my motherboard (no dedicated sound card). The cable has 2 volume wheels labelled "Game" and "Chat". I would like to be able to control, say Google Hangouts or Skype volume with the chat wheel, and all other audio with the other wheel. Is this possible? The closest thing I can find is "Communications Device" vs "Device" under the Sound control panel in Windows.

  Read the article

• DFS-R (2008 and R2) 2 node server cluster, all file writes end in conflictAndDeleted

  - by Andrew Gauger

  Both servers in a 2 server cluster are reporting event 4412 20,000 times per day. If I sit in the conflictAndDetected folder I can observe files appearing and disappearing. Users report that their files saved by peers at the same location are overriding each other. The configuration began with a single server, then DFS-R was set up using the 2008 R2 wizard that set up the share on the second server. DFSN was set up independently. Windows users have drives mapped using domain based namespace (\domain.com\share). Mac users are pointed directly to the new server share created by DFS-R. It is PC users indicating most of the lost files, but there has been 2 reports by Mac users about files reverting.

  Read the article

• Microsoft Office Compability Pack "The converter failed to open the file" error & "This is a pre-release version"

  - by HaydnWVN

  What issues have people encountered with older OS's (2000, XP) and olders versions of Microsoft Office (2000, XP, 2003) with the 'Microsoft Office Compitibility Pack'? I have a couple of Windows 2000 client PC's encountering different errors when attempting to open .docx or .xlsx documents, some with Office XP and the others with Office 2003. Reading through forums it appears that the different versions of the compatibility pack, not all were compatible with Windows 2000 (versions 3 & 4 are not). There are also Service Packs for the Compatibility Pack. With these Windows 2000 clients, it seems i need the Compatibility Pack version 2, then to install the Service Packs, yet i'm unable to find a link for version 2 of it. First error message: "This is a pre-release version of the Compatibilty Pack and can open pre-release Office 2007 files only." Is solved below. Second error message: "The converter failed to open the file." Is still on going.

  Read the article

• Boot time virus scan from USB drive

  - by Tomas Sedovic

  I want to check for viruses on a computer that I suspect may be infected with malware. Its users are running an antivirus, but there's always the risk that something slips past and the way I see it, once the system is infected the antivirus is useless because the malware can hide itself from the AV. I think the best way to go (besides clean reinstall of the OS) would be to have an antivirus running at a boot time from a CD or a USB key. That way, the malware is just lying on the disk and cannot do any of its hide-and-seek stuff (provided the AV comes from an uninfected PC and all that). So, I'm looking for something that: Runs at boot time (off USB key or CD-ROM) Does not touch or require the local OS Discovers malware fairly well (like, Avast, AVG, Norton, whatever -- I think the're all the same anyway) Can handle Windows filesystems (FAT 32, NTFS, WinFS ;-) ) Comes from some sort of trusted source (no Windows Antivirus 2009) I know that this is no silver bullet (nothing is, really*), but I do have a feeling it's more likely to help than doing the scan* within the infected system.

  Read the article

< Previous Page | 222 223 224 225 226 227 228 229 230 231 232 233  | Next Page >