Search Results

Search found 25894 results on 1036 pages for 'ask the readers'.

Page 228/1036 | < Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >

  • Help identifying device and driver for 0bda:1724

    - by user104547
    I've got a new Lenovo Ideapad Yoga 13. The onboard lan/bluetooth device is identified in Linux as 0bda:1724 (via lsusb). No network peripherals are reported from lspci. From the interwebs, the vendor:product above looks to be RT2573, however, in Windows, the device is identified as RTL8723A. Unfortunately, I have followed both roads, trying rt2500usb, rt2x00usb, and rtl8723e. I have emailed Realtek asking them for help but so far my email has fallen on deaf ears. I've posted the output of lspci -nn -v and lsusb -v to: http://pastebin.com/dqvTSVjF Any help at all would be appreciated. Thank you, Ryan

    Read the article

  • mdadm starts resync on every boot

    - by Anteru
    Since a few days (and I'm positive it started shortly before I updated my server from 13.04-13.10) my mdadm is resyncing on every boot. In the syslog, I get the following output [ 0.809256] md: linear personality registered for level -1 [ 0.811412] md: multipath personality registered for level -4 [ 0.813153] md: raid0 personality registered for level 0 [ 0.815201] md: raid1 personality registered for level 1 [ 1.101517] md: raid6 personality registered for level 6 [ 1.101520] md: raid5 personality registered for level 5 [ 1.101522] md: raid4 personality registered for level 4 [ 1.106825] md: raid10 personality registered for level 10 [ 1.935882] md: bind<sdc1> [ 1.943367] md: bind<sdb1> [ 1.945199] md/raid1:md0: not clean -- starting background reconstruction [ 1.945204] md/raid1:md0: active with 2 out of 2 mirrors [ 1.945225] md0: detected capacity change from 0 to 2000396680192 [ 1.945351] md: resync of RAID array md0 [ 1.945357] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [ 1.945359] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync. [ 1.945362] md: using 128k window, over a total of 1953512383k. [ 2.220468] md0: unknown partition table I'm not sure what's up with that detected capacity change, looking at some old logs, this does have appeared earlier as well without a resync right afterwards. In fact, I let it run yesterday until completion and rebooted, and then it wouldn't resync, but today it does resync again. For instance, yesterday I got: [ 1.872123] md: bind<sdc1> [ 1.950946] md: bind<sdb1> [ 1.952782] md/raid1:md0: active with 2 out of 2 mirrors [ 1.952807] md0: detected capacity change from 0 to 2000396680192 [ 1.954598] md0: unknown partition table So it seems to be a problem that the RAID array does not get marked as clean after every shutdown? How can I troubleshoot this? The disks themselves are both fine, SMART tells me no errors, everything ok.

    Read the article

  • Can't enable wireless lan on Fujitsu Siemens A1665G with Ubuntu 11.10 installed

    - by Theo
    I saw my old Notebook yesterday and wanted to make that work again. On Windows XP the wireless worked still fine. Then I installed new Ubuntu 11.10 32bit and I'm sadly not able to make the wireless enabled. [I replaced Win XP entirely] lspci lists following network: 08:0a.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) So after recommendation from this link I installed the b43 firmware module. iwconfig prints the following: wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associatd Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management: off As you can see, my wireless lan adapter is not turned on. sudo iwconfig wlan0 txpower auto Doesn't change anything. Then I tried to make it work with rfkill. rfkill list 0: phy0: Wirless LAN Soft blocked: no Hard blocked: yes sudo rfkill unblock all rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes remains the same. The question is now, how I could enable the hard blocked wireless LAN. There is no hardware switch for wlan integrated. However there is a button to change the state. I always thought this would be software sided, but it seems to make some hardware changes as well... The wireless LED is also not blinking (as it did on windows xp) I reset bios and searched for some settings in there, but it has only a few options and nothing to do with wireless settings, nothing works here.. At last I tried to install the acer hotkeys but I was not able to manage that. I installed the acerhkgui package, but in initializing progress, it was not able to compile acer hotkeys for my machine. There was a message that asm/linkage.h was not found while compiling. Do you have any ideas what I could do to make this hard blocked stuff disabled and my wireless card work? PS: I also tried sudo rm /dev/rfkill and a reboot to reinit that stuff... No success :(

    Read the article

  • How to change inode change time of a file?

    - by Emerald214
    I tried to use touch -d "2011-09-15 16:50" test.txt but it just modify last access time and last modified time. Access: 2011-09-15 16:50:00.000000000 +0700 Modify: 2011-09-15 16:50:00.000000000 +0700 Change: 2011-11-15 16:56:55.620124149 +0700 How to change the last change time? I want to do this because my crontab use filectime($file) to get the last changed time, so I need to create a file of two months ago to test something.

    Read the article

  • Ubuntu failed to detect monitor and very low resolution?

    - by Hiren
    I tried different versions of Ubuntu from 11.04 to 11.10 beta, but got same problem. My desktop pc configuration is, - intel core i5 2400 - DH67BL Motherboard - Inbuilt motherboard graphics - No extra graphics card attached - Acer-H193HQV 18.5" Monitor - 2GB RAM - 250GB Harddisk Problem : Ubuntu can't detect my monitor and saying it Unknown. Moreover, monitor's original resolution is 1366x768 but in the list of resolution there is only 1024x768 and 800x600 are there.

    Read the article

  • File system maintenance error, press ctrl+d to continue

    - by user3215
    In my office I've Ubuntu 8.10 desktop installed and it's running for a long time. When ever the system is started, I'll get a file system maintenance error and something it's prompted for the root password or (press ctrl+d to continue). After pressing Ctrl+D the system normally boots up. I could not resolve this issue for a long time and I think something should be done in the fstab file. I'm not sure to do anything and expecting the experts here to help to perfectly fix this. Any help is appreciated. Thanks!

    Read the article

  • How can I tweak this split-tar-gz-archive script?

    - by Sai
    I came across this shell script that can be used to split an entire directory across multiple compressed files. I am interested in making a minor tweak to this script. Lets say I have n GB of files in a directory. I do not want the contents of a particular folder to be split across multiple tar files but inside the same file. I want the n MB folder to be fit within a single compressed file and the remaining (n GB -n MB) split across multiple files. I am not sure whether it is possible with this script. I was looking forward to some suggestions. Though the script has been well documented, it is quite complex to understand for me

    Read the article

  • Laptop freezes on boot, not sure where to start

    - by J. Pablo Fernández
    I have an Ubuntu laptop that stops responding when booting up. It will change between consoles with ctrl-alt-FN but pressing enter in the console would not even enter a blank line. The last printed line when booting up in recovery mode was "Skipping EDID probe due to cached edid". Any ideas what might be wrong? Pressing ctrl-alt-del successfully rebooted it when in that mode. Another symptom is that GRUB stopped booting automatically, not sure if related (I doubt it).

    Read the article

  • Installing the Wacom Bamboo Pen & Touch

    - by federico
    I would like to use the Wacom Bamboo "Pen & Touch" with Ubuntu Maverick and I don't have any idea how to do this. In addition, when I see "change or add kernel" I become really scared. :-) I would really appreciate your help. Thanks in advance I saw answers for the Wacom Bamboo "pen" but I don't know if the installation instructions are the same or if some different additions need to be made to my system.

    Read the article

  • How to improve performance of ubuntu server 10.04 for my dms system?

    - by prasanna
    I will be using one of the dms (document management system) which is java + jackrabbit + postgresql + jboss + openoffice based on ubuntu server 10.04. this is the only application i will running on my server. i want to speed up the performance of the system for this. can you give me tips for improvements of ubuntu server? can i change any settings which give fast system performance. My application will be used concurrently by around 70 - 80 people. We have total 600 users. they will constanly upload , download the files in dms. i am going to use dedicated dell server with minimum 4 gb of RAM. i appreciate help. thanks and regards, Prasanna

    Read the article

  • Can I prevent an IDENTIFY PACKET DEVICE command to a specific device at boot?

    - by Brian Spisak
    This is related to a previous question related to installation that is now resolved. I'm opening a new question, because I still need to get my DVD drive working. Problem: Failed boot when my ASUS DRW-24B1/ST DVD drive is attached to my asmedia ASM1061. Symptom: ata8.00: exception Emask 0x52 Sact 0x0 SErr 0xffffffff action 0xe frozen ata8: SError: { blah blah } ata8.00: failed command: IDENTIFY PACKET DEVICE ata8.00: cmd blah blah res blah blah (ATA bus error) ata8.00: status: { DRDY } ata8: hard resetting link Background: The ASM1061 is a PCIe to SATA bridge providing 2 x 6Gb/s ports and is supposed to be fully compliant to SATA specs. I just discovered in the fine print of my ASUS P8Z77-V pro motherboard that "These SATA ports are for data hard drivers only. ATAPI devices are not supported." However, I have already installed Windows 7 using this drive and I can run the Ubuntu 12.04 installer from it as well. The only time I have a problem is during Ubuntu boot when it tries an IDENTIFY PACKET DEVICE which seems to be an ATAPI command. I can't simply switch this device to another SATA port because they are already allocated to other devices. (My chipset's 2 x 6Gb/s are connected to my boot SSD and a fast HDD while the 4 x 3Gb/s ports are running a RAID 5 array.) If this can't be fixed or worked around, I suppose I'll have to go buy SATA add-in card. Blech. Thoughts: If indeed this is a device specific issue (that it doesn't support ATAPI discovery) then I can't expect - is it udev? - to work with it. But, it seems that Windows and even the Ubuntu installer work just fine. So why does udev have a problem? At the end of the day, it would be nice to have the DVD working under Ubuntu, but I can live without it. But, as this is a dual-boot machine, I can't physically disconnect it because I want it to work with Windows. (And physically disconnecting it every time I want to boot Ubuntu is NOT an option. ;-) Questions: Should this be considered a bug? My feelings are that if it works with other OS that it should probably work with Ubuntu as well. How can I work around this problem? I have a limited knowledge of linux internals, but it seems I should be able to somehow tell udev (or whatever is doing the discovery) to ignore that device. Is there a way?

    Read the article

  • HDMI port not recognized on Sony Vaio

    - by julio
    I am running Ubuntu 11.10 64bit with a Sony VAIO VPC F11. It has an NVIDIA GeForce 310M video card, with the latest Nvidia drivers for the 64 bit linux, and a Windows partition with Win7 64bit. NVIDIA driver version is NVIDIA-Linux-x86_64-280.13 External monitor is Samsung SyncMaster P2770 If I boot into the Windows partition, the HDMI works as expected, with sound and video-- under linux, the HDMI port is not recognized at all, apparently, and provides no signal to the attached monitor. The nividia-settings tool does not recognize any monitor connected to the HDMI port. Disper is installed and cannot recognize an attached external monitor. Can anyone help me diagnose this issue and fix it if possible? The laptop has only the one HDMI port to connect any external monitor, so it I can't get this working I'm stuck using either the laptop screen or Windows. Thanks

    Read the article

  • Why is the root partition on my disk full?

    - by Agmenor
    I installed Ubuntu 12.04 by doing a fresh install where there was previously Ubuntu 11.10. My computer warns me now that my disk is nearly full. After having run apt-get purge, run apt-get autoremove and emptied the Trash can, I still have this problem as shown by this screenshot of Gparted: The disk /dev/sda7 is indeed full. I ran the Disk Usage Analyzer (Baobab) and I am still not sure of what is happening: One of my hypothesis is that when installing Ubuntu 12.04, I didn't configure my disks well and the disk /dev/sda6 is not mounted well as /home. Is this the reason indeed? What should I do to verify this and then to get the things fixed? Here are a few additional details to answer the questions I received (thank you everybody): My home directory is not encrypted. The Backup utility (Déjà Dup) is not set for automatic backups. (I do it myself and manually.) After I mount /dev/sda6, the command df -h gives Filesystem Size Used Avail Use% Mounted on /dev/sda7 244G 221G 12G 96% / udev 3,9G 4,0K 3,9G 1% /dev tmpfs 1,6G 904K 1,6G 1% /run none 5,0M 0 5,0M 0% /run/lock none 3,9G 164K 3,9G 1% /run/shm /dev/sda6 653G 189G 433G 31% /media/8ec2fa69-039b-4c52-ab1b-034d785132a1 (sorry but formatting this into code does not work, for an unknown reason) Thanks to izx's post, I realized /dev/sda6 was not even mounted before. It contains all the documents I used to have when I was running Ubuntu 11.10.

    Read the article

  • How to I get the fingerprint reader to work on a HP ProBook 4530?

    - by RofaelEmil
    My laptop (HP ProBook 4530) has a fingerprint device but ubuntu 12.04 didn't configure it automatically. In an effort to get it to work I installed Fingerprint-GUI. It tells me "no device detected". I checked that it is enabled in the BIOS settings. I already tried the following. sudo add-apt-repository ppa:fingerprint/fingerprint-gui sudo apt-get update sudo apt-get install libbsapi policykit-1-fingerprint-gui fingerprint-gui and sudo apt-get install fprint-demo libfprint-dev libfprint0 libpam-fprint aes2501-wy I tried adding Additional drivers

    Read the article

  • cannot access ubuntu 12.04 SAMBA share from windows 7 using hostname

    - by user98398
    I've been trying for days to get this working, and everywhere I look online it seems no one has a definitive answer, so here is the run down: I have an external drive attached to my ubuntu 12.04 machine, "nicholas-desktop." I have the entire drive shared over the network via SAMBA. If I try to access the drive from windows 7 by using "\nicholas-desktop" it fails saying it cannot locate "nicholas-desktop." However, if I use the current IP address assigned to my machine by my router's DHCP server by typing "\192.168.2.XXX" I have no problems accessing the share. if I try to ping my ubuntu machine's hostname from windows it fails. The same happens if I try to ping my windows machine, "nicholas-laptop" from my ubuntu machine. Again, if I use either machine's assigned IP address it works fine. Can someone please help me get this working? I don't want any workarounds like setting a static IP, or DHCP reservation, I want to be able to resolve hostnames from both sides. I have tried enabling SAMBA'a WINS server so I could resolve the hostnames using netBIOS, however that didn't work either, I may have made a mistake setting it up though. Thanks for your time, NCB

    Read the article

  • How to check command line requests routed thru TOR?

    - by Chris
    I think I have virtualbox set up so that all traffic originating from the guest OS is routed through TOR. TOR is only installed on the host OS and the web browsers on the guest OS all report TOR IP's in Europe when I test with seemyip.com. The host OS shows my real IP when going to the same sites. But I initiate a lot of requests from the Linux command line and I haven't been able to confirm to my satisfaction that these are routing through TOR, though I have no reason to think they do not. When I use this command I get no output from the guest OS, but my real IP from the host OS: dig myip.opendns.com @resolver1.opendns.com +short This bash file gives no output from either OS: #!/bin/bash echo Your external IP Address is: wget http://Www.whatismyip.com -O - -o /dev/null | grep '<TITLE>' | sed -r 's/<TITLE>WhatIsMyIP\.com \- //g' | sed -r 's/<\/TITLE>//g' exit 0 Suggestions?

    Read the article

  • Vdpau performance in Precise with Unity 3d

    - by bowser
    vdpau seems to be broken in Precise under Unity 3d. CPU usage ranges around 50-70% for 1080p movies while same movies utilizes around 5-10% in Natty with vdpau enabled (under Unity3d) The card is Nvidia G105m. It doesn't seem to be a Nvidia driver problem because in gnome-shell everything works as expected and I have tried different versions of Nvidia drivers (295.20, 295.33, 295.40 and the latest 302.XX from xorg-edgers) The results are all the same, works in Gnome Shell but not in Unity 3d. Disabling syn to vbank works if movie is not in full screen mode, but it doesn't work for full screen. I have searched around and haven't found much info. I am wondering if others are experiencing the same problem and if there are some known work around that I have missed. Unity 3d is otherwise very nice in Precise, but this is a show stopping issue for me (literally). Thanks. I have filed a bug here https://bugs.launchpad.net/unity/+bug/993397

    Read the article

  • Setting up Ubuntu Server as a Router with DHCPD and 3 Ethernet devices

    - by cengbrecht
    My configuration: Ubuntu 12.04 DHCP3-server eth0, eth1, eth2 Edit: removed br0&br1 eth0 is the external connection eth1 & eth2 are the internal network eth1 and eth2 are supposed to be seperate networks of student/teachers respectivly. What I would like to have is the internet from external device bridged to device 1 and 2, with the DHCP server controlling the two internal devices. Its already working with DHCP, the part I am stuck on is bridging for internet. I have setup a script that I found here: Router With the original script he linked here: Ubuntu Router Guide echo -e "\n\nLoading simple rc.firewall-iptables version $FWVER..\n" IPTABLES=/sbin/iptables #IPTABLES=/usr/local/sbin/iptables DEPMOD=/sbin/depmod MODPROBE=/sbin/modprobe EXTIF="eth0" INTIF="eth1" INTIF2="eth2" echo " External Interface: $EXTIF" echo " Internal Interface: $INTIF" echo " Internal Interface: $INTIF2" EXTIP=`ifconfig $EXTIF | grep 'inet addr:' | sed 's#.*inet addr\:\([0-9]\{1,3\}\.[0-9]\{1,3\}\.[0-9]\{1,3\}\.[0-9]\{1,3\}\).*#\1#g'` echo " External IP: $EXTIP" #====================================================================== #== No editing beyond this line is required for initial MASQ testing == The rest of the script below this is as is. I can get ip from the eth1 & eth2 devices, and my computer can see them, and them it, however, internet is not being passed through. If you need more information please just let me know. EDIT: So I had a 255.255.254.0 network, I believe that was causing the issue. Not sure if it will matter on the second card, I will test later. After changing the subnet to 255.255.255.0 the pings will pass through, however, I cannot get DNS requests to pass? My new Config for Firewall Rules # /etc/iptables.up.rules # Generated by iptables-save v1.4.12 on Wed Nov 28 19:43:28 2012 *mangle :PREROUTING ACCEPT [39:4283] :INPUT ACCEPT [39:4283] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [12:4884] :POSTROUTING ACCEPT [13:5145] COMMIT # Completed on Wed Nov 28 19:43:28 2012 # Generated by iptables-save v1.4.12 on Wed Nov 28 19:43:28 2012 *filter :FORWARD ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A FORWARD -j LOG -A FORWARD -m state -i eth1 -o eth0 --state NEW,ESTABLISHED,RELATED -j ACCEPT -A FORWARD -m state -i eth2 -o eth0 --state NEW,ESTABLISHED,RELATED -j ACCEPT -A FORWARD -m state -i eth0 -o eth1 --state NEW,ESTABLISHED,RELATED -j ACCEPT -A FORWARD -m state -i eth0 -o eth2 --state NEW,ESTABLISHED,RELATED -j ACCEPT COMMIT # Completed on Wed Nov 28 19:43:28 2012 # Generated by iptables-save v1.4.12 on Wed Nov 28 19:43:28 2012 *nat :INPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -o eth0 -j MASQUERADE -A POSTROUTING -o eth0 -j SNAT --to-source 192.168.1.25 COMMIT # Completed on Wed Nov 28 19:43:28 2012 Not sure what else you may need, but I am using Webmin to control the server(Needed for the operators on site to know how to use it.) If you could explain it as standard CLI commands, or edits to this file directly then we should be ok. :) And thanks again Erik, I do believe your edits did help.

    Read the article

  • Apple Magic Trackpad multitouch configuration

    - by Sureshkannan Duraisamy
    Today I installed the Ubuntu 10.10 release on my Desktop PC. I was running Ubuntu 10.04 LTS with an Apple Magic Trackpad and everything was working fine. After today's fresh installation of Ubuntu 10.10, I don't see my Apple Magic Trackpad's multitouch working. Two-finger scrolling and three-finger third mouse button clicking are completely broken. Has anyone else experienced a similar issue? Has anyone had success with Ubuntu 10.10 and an Apple Magic TrackPad? Please help me to fix this issue. Your help is highly appreciated...

    Read the article

  • Support for HRT Music Streamer II

    - by Duckers
    I'm considering a HRT Music Streamer II DAC (digital analog converter) for my HTPC. I run Ubuntu 10.10, but considering a upgrade to 11.04. Will this DAC be P'n'P, or at least easy to set up? http://www.highresolutiontechnologies.com/support/ indicates its supported on Mac and Windows. Linux is not mentioned. All my searches seems to indicate that its a bit troublesome, but those are posts from 2009 and older.

    Read the article

  • passwordless ssh not working

    - by kuurious
    I've tried to setup a password-less ssh b/w A to B and B to A as well. Generated the public and private key using ssh-keygen -trsa on both the machines. Used the ssh-copy-id utility to copy the public-keys from A to B as well as B to A. The passwordless ssh works from A to B but not from B to A. I've checked the permissions of the ~/ssh/ folder and seems to be normal. A's .ssh folder permissions: -rw------- 1 root root 13530 2011-07-26 23:00 known_hosts -rw------- 1 root root 403 2011-07-27 00:35 id_rsa.pub -rw------- 1 root root 1675 2011-07-27 00:35 id_rsa -rw------- 1 root root 799 2011-07-27 00:37 authorized_keys drwxrwx--- 70 root root 4096 2011-07-27 00:37 .. drwx------ 2 root root 4096 2011-07-27 00:38 . B's .ssh folder permissions: -rw------- 1 root root 884 2011-07-07 13:15 known_hosts -rw-r--r-- 1 root root 396 2011-07-27 00:15 id_rsa.pub -rw------- 1 root root 1675 2011-07-27 00:15 id_rsa -rw------- 1 root root 2545 2011-07-27 00:36 authorized_keys drwxr-xr-x 8 root root 4096 2011-07-06 19:44 .. drwx------ 2 root root 4096 2011-07-27 00:15 . A is an ubuntu 10.04 (OpenSSH_5.3p1 Debian-3ubuntu4, OpenSSL 0.9.8k 25 Mar 2009) B is a debian machine (OpenSSH_5.1p1 Debian-5, OpenSSL 0.9.8g 19 Oct 2007) From A: #ssh B works fine. From B: #ssh -vvv A ... ... debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /root/.ssh/identity ((nil)) debug2: key: /root/.ssh/id_rsa (0x7f1581f23a50) debug2: key: /root/.ssh/id_dsa ((nil)) debug3: Wrote 64 bytes for a total of 1127 debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Trying private key: /root/.ssh/identity debug3: no such identity: /root/.ssh/identity debug1: Offering public key: /root/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 368 bytes for a total of 1495 debug1: Authentications that can continue: publickey,password debug1: Trying private key: /root/.ssh/id_dsa debug3: no such identity: /root/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password: Which essentially means it's not authenticating using the file /root/id_rsa. I ran the ssh-add command in both the machines as well. The authentication part of /etc/ssh/sshd_config file is # Authentication: LoginGraceTime 120 PermitRootLogin yes StrictModes yes RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files I'm running out of ideas. Any help would be appreciated.

    Read the article

  • I cannot update my version 12-04. After installation of 12.04 I get only error reports when I try to update

    - by cees groenewoud
    received report: from Google translate : Could not initialize the package information There was an insoluble problem occurred while initializing the package information. Please this error in the package "update-manager" to report and add the following message to: 'E: Encountered a section with no Package: header E: Problem with Merge List / var/lib/apt/lists/nl.archive.ubuntu.com_ubuntu_dists_precise_main_i18n_Translation-en, E: The package lists or status file could not decompose or not be opened. " Kon de pakketinformatie niet initialiseren Er heeft zich een onoplosbaar probleem voorgedaan bij het initialiseren van de pakketinformatie. Gelieve deze fout in het pakket ‘update-manager’ te rapporteren en voeg de volgende foutmelding toe: 'E:Encountered a section with no Package: header, E:Problem with MergeList /var/lib/apt/lists/nl.archive.ubuntu.com_ubuntu_dists_precise_main_i18n_Translation-en, E:De pakketlijsten of het statusbestand konden of niet ontleed, of niet geopend worden.'

    Read the article

  • Can't Authorize Facebook in Gwibber

    - by Ashish
    Whenever I try to add Facebook account in Gwibber, It gives the following error: **Unable to load page** Problem occurred while loading the URL https://graph.facebook.com/oauth/authorize?scope=publish_stream%2Cread_stream%2Cstatus_update%2Coffline_access%2Cuser_photos%2Cfriends_photos&redirect_uri=http%3A%2F%2Fwww.facebook.com%2Fconnect%2Flogin_success.html&type=user_agent&display=popup&client_id=71b85c6d8cb5bbb9f1a3f8bbdcdd4b05 **Cannot resolve proxy hostname ()** How can I fix it?

    Read the article

  • 'Quickly': How can I use Ruby?

    - by ragu.pattabi
    Recently I came across Quickly. A very nice thing Ubuntu is doing in order to simplify creation of good looking applications that integrates well with Ubuntu desktop in every respect. While the demo was so cool and even motived me to learn Python, I am only familiar with Ruby. I would really love if there is a way to make Quickly do similar thing with Ruby. I read something about templates; but couldn't locate much details.

    Read the article

  • Wireless not detected on an hp Pavilion g6

    - by Earl Larson
    I just bought an HP Pavilion g6 laptop and I installed Natty Narwhal alongside Windows 7. In Windows 7, my WiFi works perfect but in Ubuntu it absolutely (no matter what I do) won't detect my home WiFi network. Here is the output of "lspci": earl@ubuntu:~$ lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge 00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (int gfx) 00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2) 00:11.0 SATA controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode] 00:12.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:12.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:13.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:13.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 42) 00:14.1 IDE interface: ATI Technologies Inc SB7x0/SB8x0/SB9x0 IDE Controller (rev 40) 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) (rev 40) 00:14.3 ISA bridge: ATI Technologies Inc SB7x0/SB8x0/SB9x0 LPC host controller (rev 40) 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge (rev 40) 00:14.5 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI2 Controller 00:16.0 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB OHCI0 Controller 00:16.2 USB Controller: ATI Technologies Inc SB7x0/SB8x0/SB9x0 USB EHCI Controller 00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control 01:05.0 VGA compatible controller: ATI Technologies Inc M880G [Mobility Radeon HD 4200] 01:05.1 Audio device: ATI Technologies Inc RS880 Audio Device [Radeon HD 4200] 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05) 03:00.0 Network controller: Ralink corp. Device 5390 04:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5209 (rev 01) earl@ubuntu:~$

    Read the article

< Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >