Search Results

Search found 12149 results on 486 pages for 'palm desktop'.

Page 228/486 | < Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >

• Failure to obtain IP with ARP over Wi-Fi with personal Wi-Fi router in client mode

  - by axk

  I'm trying to connect a Samsung TV to the Internet using a TL-MR3020 personal wireless router in client mode. The TV fails to connect to the network. It sees the ethernet cable connected though. Here's my network topology: Here's what I've captured with Wireshark filtering for ARP (eth.type == 0x0806): It appears the TV fails to get the IP of the gateway (DSL modem/router) for some reason. One thing I've noticed is that the source MAC for the ARP requests coming from the TV is the MAC of the Portable wireless router (that is cd:89:00), not the TV itself and the modem sends the responses to that MAC (I'm not an expert and don't know if its okay or it may make the TV fail to get the requested IP). Also I'm able to ping the TV from the DSL router (through the telnet interface) and the router has an entry in its MAC table for the TV's IP with the Portable wireless router's MAC (that is cd:89:00). If I'm able to ping the TV I suppose it should know the router's MAC to respond to the ping, but then why these continuous ARP requests... I've also tried to connect my desktop trough this Portable wireless router the same way I'm trying to connect the TV and it works fine, I can set the DSL Modem's IP as the default gateway on the desktop's NIC and connect to the Internet. The TV can connect to the Internet when connected to the DSL Router with a wired connection. Any suggestions on what may be the cause of the problem / how to further debug it are welcome. Thanks!

  Read the article

• Network connection keeps dropping - bad hardware?

  - by Bill Sambrone

  Hello all, I've into a bit of a wall with a client of mine. In an office of 20 people, he is the only one who experiences broken connections to his mapped network drives. I have everyone set up with about 6 mapped drives, all pointing to the same server (no DFS), and everyone else can access them lightning fast. The environment consists of a mix of Windows 7 and XP machines, all 32-bit. The server holding the data everyone is mapping to is running on Server 2008 R2, and is a domain controller. We recently swapped out their old 10/100 switch for a shiny new Dell PowerConnect gigabit switch. We have also replaced an old dying Sonicwall with a shiny new one. Everything is running on an ESX host except for the DC, where everyone is getting data from. In my client's office, we have done the following: Swapped out his computer (Win7 and XP box) Swapped out the desktop switch in his office Removed the desktop switch in his office Changed out the network cable going to the wall Ran 'net config server /autodisconnect:-1' on the server Disabled remote differential compression on his current Win7 box When we swapped out his network cable, everything seemed fine for about 4 days. Normally I would get a phone call a couple times per day letting me know that Outlook has crashed (there is a 9GB PST living on the server he is always connected to), or that his software he is running from his L drive has crashed. I almost thought I had this solved, but after we rebooted the DC the other night he all of a sudden couldn't stay connected to his mapped network drives for more than 10 minutes. When I ran 'net use' from the command prompt, it listed all the network drives where were randomly in a state of 'OK', 'Disconnected', or 'Reconnecting'. What else should I try? Maybe there is bad wiring in the wall, patch panel, or a bad port in the new switch I have in the server room?

  Read the article

• Roaming Profiles & Redirected Folders - storage consumption? offline files and caching?

  - by Ben Swinburne

  I understand the concepts of both roaming profiles and folder redirection and have used both separately before. I am about to set up a network from scratch and would ideally like to use both for the following reasons primarily Roaming profiles allow users to log on to any machine and have their profile Redirected profiles allow users to have their My Documents and Desktop etc backed up without the need to log off at the end of the day. The servers can run their backups overnight and there are no missing files due to the user not logging off. Redirected profiles largely alleviate the slow log in times caused by large profiles. My question is if some of the folders are redirected and therefore not part of the roaming profile what happens on machines which truly roam (i.e. laptops)? If there's offline files or a cache does this mean that the problem whereby a user has to log off comes back? By having them both enabled, is there any duplication i.e. if I have a users$ share and a profiles$ share would I have Desktop twice for example?

  Read the article

• CMD/ADB - Autorun script to search, copy, and paste a file from android system to flash drive

  - by Outride

  I've looked around and can't find anything that answers my question. This is my first question, so any tips or thoughts are welcome, as well as an answer :p As explained in title, i want to create a script that launches, finds a file on android phone, copies it, and pastes it to a flash drive. As of right now, it's a mix of multiple tutorials, trial and error, and I'm at a point of giving up. As of right now, I have a flash drive, loaded with three scripts. As follows: Bold = name of file file.bat @echo off :: variables /min SET odrive=%odrive:~0,2% set backupcmd=xcopy /s /c /d /e /h /i /r /y echo off %backupcmd% "C:\Users\Outride\Desktop\kikDatabase.db" "%drive%\all" @echo off cls invisible.vbs CreateObject("Wscript.Shell").Run """" & WScript.Arguments(0) & """", 0, False launch.bat wscript.exe \invisible.vbs file.bat So far, I had to use android commander, manually go through the directory, find /data/data/kik.android/databases and then copy kikDatabase.db to my desktop. Then run this scrip. Yes i'm trying to pull the database to copy all my email contacts. I use launch.bat, which then makes file.bat invisible due to the invisible.vbs script. What would i need to do now to have the file searched for and copied to the flashdrive? Thanks in advance, i'll be glad to answer any questions if theres any :p just remember that i'm not exactly a tech expert haha EDIT* Cleared junk of prior edits. New - I now have a .bat script to recognize what drive the usb is on, and launch py_cmd (adb shell) This is the current script. pull.bat @echo off :: variables SET odrive=%odrive:~0,2% set launching=start "%drive%\Minimal ADB and Fastboot\py_cmd" echo off %launching% so how could I make it for the .bat or a new script, to type the following "adb pull /data/data/kik.android/databases/ %drive%\All\Database" into the adb terminal? please help! I've been racking my brain over this all night :3

  Read the article

• Over gigabit connection, Teracopy does 31MB/s, but Windows 8 does it at ~109MB per second?

  - by Gaurang

  I got my brain-melting first taste of Gigabit networking today, between my 2011 MacMini and Windows 8 Pro desktop connected via Cat.5e to Linksys WRT320N(sporting dd-WRT). After making sure that the line speed on both systems showed 1Gbps, I proceeded to copying a 2.4GB MP4 from the Mini to the Win 8 desktop (SMB sharing). Although satisfied with the 30-34 MB/s that Teracopy was showing (that was a proper step-up for me from 10 MB/s), I still was curious about this massive difference in the advertised and real-world speed. 2 hours of Google had me believing that there were other factors that resulted in less speed, SMB being one. So just for the sake of doing it, I iPerf'd both the systems and guess what that showed - around 875mbps on both systems! I then stumbled upon this little piece of info after which I turned off Teracopy and copied the same file through Windows 8's regular copier. 109 MB/s. Molten brains :) What exactly is causing this? And can I enable such speeds via Teracopy? I really dig the extra features that Teracopy has, will surely miss them now :D

  Read the article

• NumLock is so weired in Ubuntu

  - by ???

  The NumLock and the keypad is so weired in Ubuntu. I have two computers, A is a desktop, with USB keyboard, B is a laptop, with laptop keyboard and another USB keyboard. On the desktop A, whether the NumLock is on or off, the number keys on the keypad just don't work. Also the NumLock LED is always off. The logs shown in xev: KeyPress event, serial 36, synthetic NO, window 0x6800001, root 0xb0, subw 0x0, time 9541332, (172,-12), root:(1846,452), state 0x0, keycode 77 (keysym 0xff7f, Num_Lock), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False KeyRelease event, serial 36, synthetic NO, window 0x6800001, root 0xb0, subw 0x0, time 9541412, (172,-12), root:(1846,452), state 0x0, keycode 77 (keysym 0xff7f, Num_Lock), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False And on the laptop B, I found that, when the NumLock is on, then many key combinations won't work. For example, generally Ctrl-A is used to select all, but it won't work when NumLock is on. The logs shown in xev: (no log when pressed Fn+NumLock on the laptop keyboard) Logs when pressed the NumLock on the USB keyboard: (Switch On) KeyPress event, serial 40, synthetic NO, window 0xb600001, root 0xac, subw 0x0, time 22187595, (102,107), root:(1198,133), state 0x10, keycode 77 (keysym 0xff7f, Num_Lock), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False PropertyNotify event, serial 40, synthetic NO, window 0xb600001, atom 0x1b8 (XKLAVIER_STATE), time 22187601, state PropertyNewValue KeyRelease event, serial 40, synthetic NO, window 0xb600001, root 0xac, subw 0x0, time 22187723, (102,107), root:(1198,133), state 0x10, keycode 77 (keysym 0xff7f, Num_Lock), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False (Switch Off) KeyPress event, serial 40, synthetic NO, window 0xb600001, root 0xac, subw 0x0, time 22187899, (102,107), root:(1198,133), state 0x0, keycode 77 (keysym 0xff7f, Num_Lock), same_screen YES, XLookupString gives 0 bytes: XmbLookupString gives 0 bytes: XFilterEvent returns: False PropertyNotify event, serial 40, synthetic NO, window 0xb600001, atom 0x1b8 (XKLAVIER_STATE), time 22187904, state PropertyNewValue KeyRelease event, serial 40, synthetic NO, window 0xb600001, root 0xac, subw 0x0, time 22188003, (102,107), root:(1198,133), state 0x10, keycode 77 (keysym 0xff7f, Num_Lock), same_screen YES, XLookupString gives 0 bytes: XFilterEvent returns: False

  Read the article

• What XMonad Configuration Best Replicates Default Ion3 Behavior and Feature Set?

  - by mtp

  Not being very familiar with Haskell and lamenting that Ion 3 is now abandonware, I am curious if anyone out there has found a way of replicating the default Ion 3 behavior and aesthetics in XMonad. If I can't have a near-exact replica of Ion 3-style behavior in XMonad, here is what would be critical to me: Virtual desktops that are empty by default and that spawn full-screen applications, which can be split horizontally or vertically evenly, leaving an empty adjacent pane. The panes, which house open windows, are manually resizable, preferably via keyboard. The panes exhibit tabbed behavior, meaning that they can house multiple windows. Windows can be tagged and moved between panes / virtual desktops via keyboard sequence. A given window may be temporarily exploded into full-screen mode via keyboard sequence. Each new virtual desktop starts in the same state—i.e., with one pane. Each virtual desktop may have its panes divided independently of other virtual desktops. From my investigation, it appears that there are several configurations that provide #3. For as much as I want to spend the time to familiarize myself with Haskell, I just simply don't have time. Any suggestions would be greatly appreciated. As far as I can tell, Ion has no conception of master pane or window, so this behavior is not desired.

  Read the article

• VT-x not enabled on 2010 Mac Pro

  - by BlindingDawn

  To start I had a Hackintosh as per the instructions from Lifehacker.com before and moved everything to a new 2010 8 Core Mac Pro. I opted for a restore from the time machine backup rather than using the migration assistance. I believe this may have caused more problems but one in particular is the lack of VT-x support. When I checked Parallels Desktop under "Host Hardware" information, I get the following that shows that VT-x isn't enabled. <Cpu dyn_lists=""> <Number>16</Number> <Model>Intel(R) Xeon(R) CPU E5620 @ 2.40GHz</Model> <Mode>1</Mode> <Speed>2400</Speed> <VtxEnabled>0</VtxEnabled> <VtxMode>1</VtxMode> 1) Does Parallels Desktop support using VT-x? 2) Does this setting show that my VT-x isn't enabled? 3) Is there a way of fixing it so that it is enabled? 4) Is there a way of using my Time Machine backup as if I'm doing a restore using migration assistance and just restore the files and settings?

  Read the article

• DVI splitter not working as expected/confusion between DVI-D and -I

  - by Freakishly

  Hey guys, thanks for looking. I have an ATI FirePro™ V3700 in my desktop machine, and I have been running a dual-monitor setup quite effortlessly, thanks to the two DVI ports on the card. I came upon a third monitor, and wanted to extend my desktop to 3 screens, so I purchased a DVI splitter from Amazon. Now, I can only duplicate the second monitor onto the third, not extend it. I've tried all possible combinations of input to no avail. Here's the setup: The ATI FirePro™ V3700 has two Dual-Link DVI-I outputs The splitter splits a single Dual-Link DVI-I port into two Dual-Link DVI-I outputs Two of the monitors are NEC E222W, and the third monitor is a Dell 2001FP. Each monitor has one D-Sub and one Dual-Link DVI-D input. Cables going from the video card to the monitors are two Dual-Link DVI-D to the NECs and one Single-Link DVI-D to the Dell. Is the problem likely with the DVI-D/DVI-I mismatch? Or is it with the cable on the Dell that is only a Single-Link? The cables are easily replaceable, the monitors not so much. Thanks for your time, I really appreciate it. http://www.amd.com/us/products/workstation/graphics/ati-firepro-3d/v3700/Pages/v3700-specs.aspx http://www.amazon.com/Cables-Unlimited-DVI-D-Splitter-PCM-2260/product-reviews/B000H09RFM/ref=dp_top_cm_cr_acr_txt?ie=UTF8&showViewpoints=1 www dot newegg dot com/Product/Product.aspx?Item=N82E16824002495 accessories dot us dot dell dot com/sna/PopupProductDetail.aspx?cs=19&l=en&c=us&sku=320-1578 Apologies for the fudged links, I'm new here and they won't let me post more than two :P

  Read the article

• Windows XP Loading Problem

  - by Sadeq Dousti

  Sometimes, my Windows XP does not load correctly. It shows the login screen, and when I click my username, it load the desktop background, but the Explorer does not show up. So, I cannot see the icons on the desktop, the start menu, etc. If I press Ctrl+Alt+Del to show Task Manager, I can run programs (like media player or browser) from File--New Task (Run...). Also, in the Task Manager, I see Explorer.exe running. I tried to kill and re-run it, but nothing happens. I used Sysinternals Process Explorer to see if there were any odd process or odd behavior, but nothing was fishy. After several restarts, the system finally worked as expected. But this is not permanent: Sometimes, when I restart the system, it works just as described above (Explorer does not show up). But sometimes it works normally. I used Kaspersky to search for viruses, but nothing showed up. I think the info presented above is not enough to pinpoint the problem. Yet you might be able to tell me about a tool or something, which I can use to give you more info, or even solve the problem. PS: I can easily use the Safe Mode. It does not seem to suffer from this problem. Hence, I suspect there's some process (service) for which Explorer is waiting, but that process runs into trouble (say a race ondition, or an infinite loop) and so Explorer stalls as well.

  Read the article

• Intermittent Trouble Entering Hibernate on WinXP

  - by kquinn

  My personal desktop, running 32-bit Windows XP SP2 (with 4GB RAM, 2.75GB addressable, swap disabled, hiberfil.sys existing and contiguous on C:\; SP3 is not installed because SP2 has been working fine and I do not want to re-qualify with SP3 just for sheer perversity) typically gets hibernated at night. For a long time this worked great, but recently the machine has had trouble entering hibernation. Sometimes when I press my power button (configured to hibernate), the box will start the procedure for hibernating (i.e., go to the blue "Windows XP" background logo and display a message about entering hibernation), but before displaying the usual blue-on-black hibernation progress bar it will drop back to the desktop. No error messages appear, on screen or in the system log. The only record of unsuccessful hibernation attempts in the system log, which proudly proclaims that "The Windows Image Acquisition (WIA) service entered the running state." once per failed hibernation attempt. The problem is almost certainly resource related: if I then close one or more applications which are running, and repeat the exact same process, the machine will hibernate perfectly. There does not appear to be a reliable high-water mark for virtual or physical memory use, below which the machine is guaranteed to hibernate; it's different every time (though typically, below about 1.1–1.4 GB memory usage seems to be where hibernate succeeds most often). Memory may not even be the relevant resource; as far as I know, it could also be handles or sockets. This behavior is relatively recent: it has only started in the last few months; before then, I could hibernate reliably no matter what the current resource use of the system. This machine claims to have hotfix Q909095 installed, but since the symptoms of my problem match KB909095 rather well, I'm suspicious if this fix is actually working as intended. Any ideas on how to fix this or where to start debugging?

  Read the article

• After upgrading to 2008 R2 Enterprise and installing more RAM, Windows can only see 4.00 GB

  - by Tom Crane

  (I have also posted this on technet but I'm running out of ideas) I've upgraded from Windows Server 2008 R2 Standard to Enterprise in order to make use of more RAM. The server previously had 32GB of RAM. The upgrade from Standard to Enterprise, using DISM, seemed to go OK, so I powered down and installed the RAM. This a Dell Poweredge T710, I was taking it from 32GB to 72GB. The BIOS recognised the RAM, although I needed to change from "Advanced ECC" to "Optimizer" mode for it to use all of it. After rebooting, windows can see the RAM but in the system panel will display: Installed memory (RAM): 72.0 GB (4.00 GB usable) In the resource monitor, the remainder of the RAM is showing as reserved for hardware. I've tried various RAM configurations, including reverting it to the same chips and same configuration as before the upgrade, but always just 4.00 GB is showing up as usable. Following some threads on these forums I've gone into msconfig and set the maximum memory "by hand" but that doesn't fix the problem. BIOS doesn't seem to have anything that looks like memory remapping which is another suggestion that has come up. How do I make this RAM available to Windows? It was available before the upgrade, because I could use the full 32GB RAM the server had to start with. A screenshot (this is after reverting to the original RAM configuration) http://screencast.com/t/5FuzevdNb I don't know if it's related, but my remote desktop configuration has also disappeared: screencast.com/t/mYedomeQWS (the bottom half of this dialog should allow me to configure Remote Desktop, it was working before the upgrade but now it isn't).

  Read the article

• How to set umask globally?

  - by DevSolar

  I am using a private user group setup, i.e. a user foo's home directory is owned by foo:foo, not foo:users. For this to work, I need to set the umask to 002 globally. After a quick grep -RIi umask /etc/*, it seemed for a moment that modifying the UMASK entry in /etc/login.defs should do the trick. It does, too -- but only for console logins. If I log in to my desktop, and open a terminal there, I still get to see the default umask 022. Same goes for files created from apps started through the menu. Apparently, the display manager (or whatever X11 component responsible) does source some different setting than a console login does, and damned if I could tell which one it is. (I tried changing the setting in /etc/init.d/rc, and no, it did not help.) How / where do I set umask globally (and for all users), so that the X11 desktop environment gets the memo as well? (The system is Linux Mint / Ubuntu, in case that changes anything...)

  Read the article

• Is having a [high-end] video card important on a server?

  - by Patrick

  My application is quite interactive application with lots of colors and drag-and-drop functionality, but no fancy 3D-stuff or animations or video, so I only used plain GDI (no GDI Plus, No DirectX). In the past my applications ran in desktops or laptops, and I suggested my customers to invest in a decent video card, with: a minimum resolution of 1280x1024 a minimum color depth of 24 pixels X Megabytes of memory on the video card Now my users are switching more and more to terminal servers, therefore my question: What is the importance of a video card on a terminal server? Is a video card needed anyway on the terminal server? If it is, is the resolution of the remote desktop client limited to the resolutions supported by the video card on the server? Can the choice of a video card in the server influence the performance of the applications running on the terminal server (but shown on a desktop PC)? If I start to make use of graphical libraries (like Qt) or things like DirectX, will this then have an influence on the choice of video card on the terminal server? Are calculations in that case 'offloaded' to the video card? Even on the terminal server? Thanks.

  Read the article

• How to remotely connect using perfmon?

  - by user36914

  Suprised there is not a ton of information on google when i search for this but there is not. Lot of people asking the question but i none of them have any good answers. I have a remote computer running hyper-v (server) running a Windows 7 x64 guest (guest). Occasionally i won't be able to remote desktop to guest. I will then remote to server and see that the guest instance is constantly using about 25% of the cpu. WHen i try to connect directly from server i will get the login screen but as soon as i type the password in it will just stay at the windows 7 login screen but the account names will disappear and it will not log in. It responds to pings though. I don't know how else to diagnose other than trying to run perfmon remotely. It only happens like every 3 weeks and i run it 24/7. So i'm trying to run remote desktop remotely. I tested this out on a local vm i have running under vmware. When i try to connect using perfmon to my local vm i get this error: "when attempting to connect to the remote computer the4 following system error occurred: the network path was not found" I found in another past to start the remote registry service and when i start the service i get this error: "No such interface supported" Anyways, how do i remotely connect to another machine with perfmon or if anyone has a better idea how i can diagnose the problem above then let me know.

  Read the article

• DNS request times out then succeeds on my local network. Why?

  - by Dan

  I have a W2K3 Server that is the Domain Controller and also the DNS server. I wanted to make another DNS zone on my network called "something.local" and then make 'A' records to point requests like 'admin.something.local' and 'www.something.local' to machines on my network. I keep getting DNS timeouts but then after 2 tries it succeeds. Why would this happen? How can I troubleshoot? From my desktop I run: nslookup admin.something.local and get: Server: server.domain.com.au.local Address: 192.168.0.10 DNS request timed out. timeout was 2 seconds. DNS request timed out. timeout was 2 seconds. Name: admin.something.local Address: 192.168.0.191 If I go back the other way: nslookup 192.168.0.191 I get: Server: server.domain.com.au.local Address: 192.168.0.10 Name: admin.something.local Address: 192.168.0.191 My DNS server address is 192.168.0.10. The new DNS zone is not hooked up to active directory. I do not have much experience with DNS. Yesterday it was working fine. I have tried doing an 'ipconfig /flushdns' on both my desktop and the DNS server

  Read the article

• Application Virtualization

  - by Peter Versnee

  I have been looking for a solution to virtualize my desktop application as a SaaS. After picking Citrix XenApp as the best solution for my case and trying for ever to get it to work (with some more experienced people) I can't help but to conclude that Citrix has too much problems for my case. Every time I fix one thing some other thing pops up. As I can't imagine Citrix XenApp is the only way to deliver my application to my clients, I'd like to ask you experienced guys if you think there is an other way to deliver it whilst meeting my requirements. I've got no money issues - time on the other hand... My requirements: My application must run on a windows server; The application should be virtualized with the application window only (no desktop); Content Redirection (my application is the only one virtualized, so PDF, DOC(X) etc. is on the users' system); Easy user management; SSO;* Cross platform (Windows, Linux, Mac OSX).* I truly hope I don't annoy you with another of the same question. I've tried to find the same question here and - obviously - didn't found it. *) these I can live without, however very much appreciated

  Read the article

• Problem with running a script at startup as root?

  - by Usman Ajmal

  Hi The main question: Is there a way I can run 'completely' one of my script when ubuntu's desktop appears no matter if root , administrator, desktop user or an unprivileged user logged in? What does the script do? The script mounts a partition, looks for a file in that partition and finally on the basis of that file a decision of copying a partition to another partition is made. That copying is done via dd if=/dev/sda2 of=/dev/sda5 When does the script run finely? Script runs smoothly when I run it from the terminal by sudo ./my_copying_script This command asks me for the password of currently logged in user. I enter the password and the script starts working. When does the script NOT run finely? I want to run the script at startup. I set it a startup program by using the Startup Applications utility of Ubuntu. Script ran at startup but exited at the dd command returing following error: dd: opening '/dev/sda2': Permission denied On edk's suggestion I set the owner of my_copying_script as root and set the SUID. Now the permissions of my_copying_script are (-rwsr-sr-x). edk's point of view was that once I set the suid, the startup program will run with the permissions of its owner. I did that but the same /dev/sda2 permission denied error came up. I then prefixed the dd with sudo as mentioned below sudo dd if=/dev/sda2 of=/dev/sda5 but this returned following error: sudo: no tty present and no askpass program specified In other words the mounting failed. If I run the script using sudo ./myProgram i don't face this problem and the drive gets mounted successfully.

  Read the article

• Using keyboard disables touchpad left button for a second on Acer laptop in Windows 8.1

  - by Robert Kilar

  The problem is present in the whole system not only in games: desktop, chrome, games, everywhere. When I press any "input key" on a keyboard for example in desktop I can't select the file by left mouse button OR by tapping the touchpad for about one second(right button works immediately). Later on the LMB works well. There is NO delay, button is just deactivated for a second. In games that means that when I run I cannot shoot for example. When I switched LMB and RMB functions in windows control panel still the LMB is getting disabled and RMB works fine. By "input key" I mean letter or a number, keys like Alt, CapsLock, Ctrl does not affect touchpad. I do not remember that problem when I used Windows 7. USB mouse works like it should. The problem existed when I was using Elantech touchpad driver and after I uninstalled it and used Windows 8.1 generic driver. EDIT I installed the Elantech drivers and set values to 0 at every disable... key. But the problem is still present. EDIT 2 THE LAPTOP IS Acer V3-571G I have turned off disabling function in touchpad but it did not fix it. I know that touchpad is NOT broken down. Turned on the animated touchpad icon of elantech drivers and put it on the task bar(on a picture) When I type the letter and press the LMB the dynamic icon displays the click but it is ignored.

  Read the article

• Windows Not Honoring DHCP Scope

  - by jerhinesmith

  Please bear with me as I'm not a networking person by trade. Our current configuration at work includes two Windows Servers serving as DHCP/Active Directory servers (if that makes sense) -- one replicating from the other. On both machines, the DNS resolution is set up as: Main Windows Box (10...* address) Public IP Address (for Verizon) Public IP Address (secondary Verizon) Secondary Windows Box (10...* address) Assuming our domain is foo.com, we maintain the foo.com website on a hosted VPS with it's own IP address. The problem is that even though bar.foo.com is an internal server and is defined in DNS on the Primary Windows machine, when I ping bar or even bar.foo.com it resolves to the hosted IP address instead of the 10.* address. I tried taking both of the Public IP addresses out of the DHCP scope, and that seemed to work, but it completely slowed down access to any external sites, so that wasn't acceptable. I also tried adding the two Windows machine as the DNS servers on my desktop. That too worked, but I'd rather not have everything enter their DNS servers, as the above setup should theoretically be working. Is there anything I could check to see why pinging bar.foo.com isn't resolving to the DNS entry on the Windows machines? Here's a summary of the ping results, if they help: Pinging from servers with static IP bar.foo.com resolves with correct IP address Pinging from linux machines not joined to the domain bar.foo.com resolves with correct IP address Pinging from user's desktop machines, joined to the domain, but dynamic IP bar.foo.com resolves with incorrect IP address This is driving me crazy!

  Read the article

• Salary Survey Entry Level network position [closed]

  - by will

  Hello, I started interning with a company about 5 months ago and for the past 7 months I have been a normal part time employee. This week I have a review, where I am hoping to get a raise. I started at $8 interning, and now I'm up to $13. What I am trying to figure out is how to survey what others are making in similar positions so I can take it to the review as a base number. here are my thoughts on my position right now. Review Thoughts My Qualifications: • Associates of applied Science - IT network Specialist • CompTIA A+ certification • CompTIA Server+ certification • CompTIA Network+ certification • Currently pursuing Cisco certifications • Junior status at Insert college Pursuing Bachelors in Information Technology with an emphasis in Networking. 3.4 GPA • 1 year of working at Insert Company. My contributions to Insert Company • Offering near fulltime through semester and fulltime through summer. • Ability to work after hours and on weekends • Developed and support helpdesk system • Set up and maintain Update server to keep desktop clients up to date • Deployed and maintain antivirus solution for end users • Assist with main projects such as SAN, Virtualization, and network survey. Any tips on determining an asking number would help. I was thinking $17-$18, am I way off here? • Migrating end user stations to Windows 7 (current project) • Developing imaging solution for Desktop PCs (current project)

  Read the article

• What is the correct authentication mechanism when there are users inside and outside the domain?

  - by Gary Barrett

  We have a Windows 7 enterprise desktop data entry app for mobile (laptop) users with local SQL Express 2008 R2 Express db that syncs data with an SQL Server 2008 R2 Server db. Authentication is required before syncing the data. The existing group of users are part of the organisation's domain so normal scenario and they connect to the Sql Server directly. But there are plans for a second group of app users who belong to various partner organisations so they are outside our domain and have their own various separate domains/accounts. The aim is to deploy the desktop app to them and they will periodically sync data to our SQL Server. What I am uncertain of: Is it possible to authenticate users from another domain? Can permissions be managed via Active Directory etc? Which authentication protocol should be used in this scenario? Windows, Forms, SQL, etc? The IT people are requesting users of the system be managed via Active Directory. Is it possible to manage the external domain users access via Active Directory?

  Read the article

• Web based KVM management for Ubuntu

  - by Tim

  We've got a single Ubuntu 9.10 root server on which we want to run multiple KVM virtual machines. To administer these virtual machines I'd like a web based KVM management tool, but I don't know which one to choose from the list of tools mentioned on linux-kvm.org. I've used virsh & virt-manager on my desktop, but would like a web interface for the server. I tested ConVirt on my desktop, but it failed to pickup KVM machines from virsh / virt-manager, and I could not get KVM virtual machine import to work (only Xen). oVirt looks good, but I can't find out if and how I can install it on Ubuntu 9.10.. (And I'd really rather not waste another few days on testing stuff that might not work in the end.) Can anyone recommend any good web based KVM management tools that are easy to install on Ubuntu 9.10? I'm looking for something that will also allow me to run other services like apache and postgresql besides hosting virtual machines, so preferably fairly lightweight & no dedicated OS installs. We don't need any professional clustering / migration or anything, just something that will let us create, start, inspect, administer & stop virtual machines from a web page. Best regards, Tim Update: Anyone have any suggestions? It's awfully quiet here..

  Read the article

• XP box with 3 NICs on Server 2003 Domain

  - by Hannibal

  I have assigned all three NICs IP addresses that are outside the DHCP pool. I have 2 NICs are connected to 1 switch and the 3rd to my second switch. I want to assign one of the two NICs on the 1st switch to "normal" network activity (e.g. internet access, RDP, etc.) The other two NICs I want to reserve for mirroring ports on their respective switches. While this machine is connected to the domain I can access the internet and Remote Desktop. I have no idea which NIC I am using until I start mirroring a port, at which time, if I happen to be connected through one of the NICs I have dedicated to mirroring, I lose my remote desktop. I am aware that I would have more control over the NICs using Linux. I want to explore Windows solutions before I go that route because reinstalling another OS would be inconvenient (but not impossible). I would likely use a version of Backtrack (3 or 4 not sure). I would also have to learn how to access the machine remotely but I've done it before so this would be a minor obstacle. Thank you for your assistance.

  Read the article

• How do I change file protections running XP on a disk from Windows Server?

  - by cdkMoose

  I had a Windows Server 2003 machine running at home, along with my desktop which I use for development. Server went belly up, but since my desktop is reasonably powerful, I figured I would move the disk from the file server (it was OK) into my XP machine to keep all of the files. Disk comes up fine and shows all of the files. I have been getting access denied errors when trying to work with some of the files. When I display attributes in Explorer, none of them are marked Read-Only. When I view properties on the directories, the Read-Only checkbox is not checked, but has a green background(which I thought meant mixed usage for files in the directory). When I click on the checkbox to clear it and click Apply, the disk does some work and all looks well. However, I continue to get the Access Denied errors, the files still don't show any Read-Only attribute and the directory properties shows the green background again on the Read-Only checkbox. I did check the box which says to apply the change to the folder and all files /subfilders under it. I am assuming that the issue relates to userids/permissions carried over from the Server install. So, why does it let me think I can change the attribute when I can't and how can I correct this problem so that the disk correctly recognizes the ids from XP?

  Read the article

< Previous Page | 224 225 226 227 228 229 230 231 232 233 234 235  | Next Page >