Search Results

Search found 24073 results on 963 pages for 'mount point'.

Page 229/963 | < Previous Page | 225 226 227 228 229 230 231 232 233 234 235 236  | Next Page >

• Combine drivers from multiple Win7 installs to single image

  - by MikeyB

  I need to prepare a Windows 7 image with drivers for multiple systems (Lenovo laptops). I currently have an image prepared on one laptop type but need to grab the drivers appropriate for the other laptop types as well to ensure that it works on all systems. From what I can tell, the procedure will be: create a boot CD with imageX take a .wim image prepared on the first type of systems take .wim images from the other systems mount the other images in WAIK extract the drivers from the other images inject the drivers into the first .wim boot a system with the boot CD and redeploy the updated .wim image into the Windows partition take an image of the drive with usual imaging tools This all seems a little too convoluted, but I'm willing to do it to get the proper drivers into the image. This is (seemingly) necessarily complicated by having more than one OS on the disk image. Am I on the right track?

  Read the article

• OpenVPN IPV6 Tunnel Radvd

  - by Arenstar

  Hello.. I have an interesting question regarding ipv6 + openvpn.. My Version is OpenVPN 2.1.1 i have been given a native /64 ipv6 network ( for this example 2001:acb:132:acb::/64 ) The plan was/is, route this block through openvpn and into an office ( for testing purposes ) Soo to explain.. I have a Centos Box as the first linux "router" in a datacenter & a Ubuntu box as the second linux "router" in the office I have created a simple point-to-point tunnel using tun ( based off ipv4 address to start the tunnel ) I have assigned to Centos /sbin/ip addr add fed1::1/128 dev eth0 /sbin/ip addr add fed2::2/128 dev tun0 /sbin/ip route add 2001:acb:132:acb::/64 dev tun0 ## ipv6 Block down the tunnel /sbin/ip route add ::/0 dev eth0 ## Default out to Gateway I have assigned to Ubuntu /sbin/ip addr add fed1::3/128 dev tun0 /sbin/ip addr add fed1::4/128 dev eth0 /sbin/ip route add 2001:acb:132:acb::/64 dev eth0 ## ipv6 Block down to eth0 /sbin/ip route add ::/0 dev tun0 ## Default up the tunnel I have also included on both servers.. sysctl -w net.inet6.ip6.forwarding=1 Looks Good... right??? Wrong.. :( I am not able to ping fed1::1 from fed1::4 (Ubuntu) (can ping :4,:3,:2) However, i can ping fed1::1 fed1::2 from :3 ?????? ( very strange ) I am able to access the internet from any ipv6 interface on the Centos Box but clearly not from the Ubuntu box.. Further, i will eventually run radvd on the Ubuntu box eth0, and autoconf the network with ipv6 address's Anyone with some advice / tips to help me out.. ??? Cheers

  Read the article

• reiserfsck --rebuild-tree failed: Not enough allocable blocks

  - by mojo

  I have a reiserfs volume that required a --rebuild-tree, but is currently failing to complete when I pass it --rebuild-tree. Here is the output that I receive when running it: reiserfsck 3.6.19 (2003 www.namesys.com) # reiserfsck --rebuild-tree started at Mon Oct 26 13:22:16 2009 # Pass 0: # Pass 0 The whole partition (7864320 blocks) is to be scanned Skipping 8450 blocks (super block, journal, bitmaps) 7855870 blocks will be read 0%....20%....40%....60%....80%....100% left 0, 9408 /sec 287884 directory entries were hashed with "r5" hash. "r5" hash is selected Flushing..finished Read blocks (but not data blocks) 7855870 Leaves among those 6105606 Objectids found 287892 Pass 1 (will try to insert 6105606 leaves): # Pass 1 Looking for allocable blocks .. finished 0%....20%....40%....60%....80%....Not enough allocable blocks, checking bitmap...there are 1 allocable blocks, btw out of disk space Aborted I can't mount it, and I can't fsck it. I've tried extending the volume, but that hasn't helped either.

  Read the article

• Fix for OpenSolaris with no gcc vs. Nexenta with no ext3

  - by Jake Wharton

  I'm attempting to migrate my server from linux to a Solaris variant during a hardware upgrade. The machine is based around an Abit AN-M2 board which has an NForce chipset. I have what seems to be a chicken-and-egg problem of sorts: OpenSolaris 2009.06 does not recognize the NIC and I cannot compile the drivers for it as it also lacks gcc. I haven't tested as to whether or not I can mount an ext3 partition yet but its moot if there is no networking. Nexenta 3.0b3 recognizes the NIC but I cannot get the ext3 drives mounted due to FSWfspart refusing to install. I do not know much about Solaris but I wager this is due to the fact that Nexenta is based around Debian as well. While I am reusing the mobo/CPU combo, I did just spent a lot of money on the other hardware around it and would very much like to get it up and running smoothly and quickly. Does anyone have any suggestions that are not: Get a new mobo/CPU Run another OS Use alternate NIC

  Read the article

• Cannot copy files from external USB HDD to computer

  - by Thomas Versteeg

  Hello I have a HDD disk connected with a USB converter to my computer. It consists of two partitions, the first one is mounted automatically and I can grab all the files from it, but the second one I have to mount manually as a root in the command line, if I try to open it with nautilus it gives an error. The drive where the problem is is drive sdb1, sdb2 has the same settings but works fine. I am using Debian Wheezy. This is the fstab: /dev/sdb1 /media/usb0 auto defaults,gid=disk,umask=0777 0 0 /dev/sdb2 /media/usb1 auto defaults,gid=disk,umask=0777 0 0 And when I try to copy the files with this command (as root) cp -vr /media/usb0/* /home/user/Videos/ I get these types of errors: cp: reading `/media/usb0/.lang/file.ext': Permission denied cp: failed to extend `/home/user/Videos/.lang/file.ext': Permission denied How can I at least copy the files to my main HDD? I don't need to adjust them I only need to copy them!

  Read the article

• Zero-channel RAID for High Performance MySQL Server (IBM ServeRAID 8k) : Any Experience/Recommendation?

  - by prs563

  We are getting this IBM rack mount server and it has this IBM ServeRAID8k storage controller with Zero-Channel RAID and 256MB battery backed cache. It can support RAID 10 which we need for our high performance MySQL server which will have 4 x 15000K RPM 300GB SAS HDD. This is mission-critical and we want as much bandwidth and performance. Is this a good card or should we replace with another IBM RAID card? IBM ServeRAID 8k SAS Controller option provides 256 MB of battery backed 533 MHz DDR2 standard power memory in a fixed mounting arrangement. The device attaches directly to IBM planar which can provide full RAID capability. Manufacturer IBM Manufacturer Part # 25R8064 Cost Central Item # 10025907 Product Description IBM ServeRAID 8k SAS - Storage controller (zero-channel RAID) - RAID 0, 1, 5, 6, 10, 1E Device Type Storage controller (zero-channel RAID) - plug-in module Buffer Size 256 MB Supported Devices Disk array (RAID) Max Storage Devices Qty 8 RAID Level RAID 0, RAID 1, RAID 5, RAID 6, RAID 10, RAID 1E Manufacturer Warranty 1 year warranty

  Read the article

• why my server has a dir named "?"

  - by liuxingruo

  These are all the dirs in my server: ? bin boot dev etc home lib lost+found media media2 misc mnt net opt proc root sbin selinux srv sys tmp usr var why there is a "?" dir? Thanks very much. BTW: the touch command was found on my server(wiered). I list the bin dir: alsacard cp dd env hostname loadkeys more ps sed tcptraceroute alsaunmute cpio df ex igawk loadkeys.static mount pwd setfont traceroute6 arch csh dmesg false ipcalc logger mountpoint raw setserial tracert awk cut dnsdomainname fgrep kbd_mode login mv red sh view basename date doexec gawk keyctl ls netstat redhat_lsb_init sleep ypdomainname bash dbus-cleanup-sockets domainname gettext kill mail nice rm sort cat dbus-daemon dumpkeys grep ksh mailx nisdomainname rmdir stty chgrp dbus-monitor echo gtar ksh93 mkdir pgawk rpm su chmod dbus-send ed gunzip link mknod ping rvi sync chown dbus-uuidgen egrep gzip ln mktemp ping6 rview tar touch is missing, how can i get it back?

  Read the article

• Server freezes while installing Redhat Enterprise Linux Server 6

  - by eisaacson

  We've tried both the first options Install or upgrade an existing system Install system with basic video driver When trying option #1, it gets to a screen that has a solid cursor about halfway down, then freezes. When trying option #2, it freezes at the point where it says: Waiting for hardware to initialize... Of course, we bought the unsupported version and haven't found anything to help us so far. Here are the specs to the server in the original post: ASUS P8Z68-M Pro LGA 1155 Intel Z68 HDMI SATA 6Gb/s USB 3.0 Micro ATX Intel Motherboard with UEFI BIOS RAIDMAX Reiter ATX-305WBP Black Steel / Plastic ATX Mid Tower Computer Case 450W Power Supply Intel Core i7-2600 Sandy Bridge 3.4GHz (3.8GHz Turbo Boost) LGA 1155 95W Quad-Core Desktop Processor Intel HD Graphics 2000 BX80623I72600 16GB Ram OCZ Agility 3 SSD 120GB From some of the posts out there could the UEFI Bios or the Sandy Bridge processor be a culprit here? We just tried the DVD on a different computer and it got past that point with ease. It's a standard Dell build compared to our custom machine. Could it be having difficulty recognizing drivers? How do we get past that?

  Read the article

• Cmd+Less Than (10.8.2) not working after Xcode (4.5.x) installed

  - by Felix Lieb

  I had to reinstall my MBP recently. I stress Cmd+Less Than a lot for switching between Xcode's main window and the Organizer for documentation. The standard OSX-shortcut for doing that is Cmd + Less Than. After installing Xcode it didn't work any longer. I saw, that Xcode uses Cmd+LT for "Edit Schemes", a rarely used option. Even after deleting the shortcut for "Edit Schemes" in Xcode, Cmd+LT didn't work. How can I get Cmd + Less Than to work again? Mac OS X Mount Lion 10.8.2 Xcode 4.5.2 I have less than 10 reputation on superuser (acutally first post here), so I can't post the answer to my question. Would yo be so kind and upvote this question, so I can officially answer the question? The question, as well as the answer is only correct, if you use German keyboard layout.

  Read the article

• Write permission when mounting Windows shares from Ubuntu

  - by Ola Tuvesson

  I think I'm close to having my dev environment set up exactly the way I want, but one final snag remains. I'm running VirtualBox on a Windows 7 64bit host, with my dev enviroment inside a Ubuntu 12.04 guest. I want to keep the files for my projects on the host filesystem - partly so I can access them when the Ubuntu guest is not running, but also so I can use Tortoise and other Windows based tools (cough Photoshop), and it also eases my backup scheme somewhat. So I've got a folder "Rails" on my NTFS drive, which I've shared from the host with a user specifically created for the Ubuntu guest. The mount point has been set up and an entry added to fstab (cifs), using a credentials file and the options iocharset=utf8,file_mode=0777,dir_mode=07??77 This mounts fine and my Ubuntu user has both read and write permissions to the contents, but when I try to start my Rails app I get permission errors on any files the app needs to write to (e.g. the log file). What gives?

  Read the article

• Installing Software from a CD onto a Netbook

  - by Jonathan Sampson

  I apologize if this question has come up before - I can't seem to find it. Tonight my wife and I purchased a small samsung netbook and have been enjoying it for a light-weight solution around the house. My wife has a game she loves to play that was installed on her last laptop, but we'd like to put it on the netbook. The problem is, there's no cd-drive on the netbook and the game must be installed from a CD. What other ways can I install software from a CD onto the netbook lacking a local cd-drive on the device itself? I would prefer to not have to create image files, and mount virtual drives, etc.

  Read the article

• Intsalling Linux on PowerEdge R410 via USB

  - by Bill Johnson

  I’m hoping someone can help me with the following issue. I have a Dell PowerEdge R410 and basically the Optical Drive has failed when I have been given the server. I have installed 2 SATA drives and want to install Ubuntu 11.04; however, each time I have tried i.e. using bootable .iso on USB it failed. I assume it's failing as with a lot of releases they all look at the CD drive. Ubunutu has failed on installation with the error message unable to mount CD. I have tried installing Microsoft Hyper-v and that also fails as during installation it asks for CD/DVD drivers. Tried embedding ISO's from various distro's (Linux and Windows) with drivers and that hasn't worked out either. Does anyone have any idea on how I can get Ubuntu on this server? Should I look towards an old distro perhaps?

  Read the article

• Windows 2008 as home file server and more

  - by Christian W

  I currently have a freenas-unit as a NAS, and a Win2k8R2-unit as server. However I would like to consolidate these to units in one. What I really like about the freenas-unit is the ZFS filesystem. And the only reason I care about the ZFS filesystem is the easy way I can grow an existing filesystem just by inserting a new drive. How would this work in Win2k8? If I setup my unit with a separate drive as C: and a 1TB drive as D:. The D: would then be segmented into d:\Videos d:\Music d:\Pictures. When everything gets close to filling the storage-drive, I would like to expand the storage, but I wouldn't want to have E:\Videos or d:\Videos2 (using the NTFS folder mount thingy). I still want all my Videos to reside in D:\Videos and I want the OS to decide which drive it's going to be stored on... Some kind of on-the-fly jbod expansion :) Is this at all possible in Windows 2008?

  Read the article

• Shared block device file system (cluster file system without networking)

  - by fungs

  Is there any file system that can be mounted multiple times and supports concurrent file access for Linux? Basically I want something like a cluster file system but without the need to have a running network for a distributed lock manager. That can be very handy in connection with virtual machines that can share data with the host or another VM without the need to create a network link. This I want to avoid to keep the network architecture secure (virtual machine in DMZ) but share large files. No need to scale it up, just two machines that mount the same block device. Shouldn't it be possible to have file locking information right on the disk?

  Read the article

• Feasibility of Windows Server 2008 DFS replication over WAN link

  - by CesarGon

  We have just set up a WAN link that connects two buildings in our organisation. The link is provided by a 100-Mbps point to point line. We have a Windows Server 2008 R2 domain controller on each side of the link. Now we are planning to set up DFS for file services across the organisation. The estimated data volume is over 2 TB, and will grow at approximately 20% annually. My idea is to set up a file server in each building and install DFS so that all the contents stay replicated over the 100-Mbps link. I hope that this will ensure that any user will be directed to the closest (and fastest) server when requesting a file from the DFS folders. My concern is whether a 100-Mbps WAN link is good enough to guarantee DFS replication. I've no experience with DFS, so any solid advice is welcome. The line is reliable (i.e. it doesn't crash often) and our data transfer tests show that a 5 MB/sec transfer rate is easily achieved. This is approximately 40% of the nominal bandwidth. I am also concerned about the latency. I mean, how long will users need to wait to see one change on one side of the link after the change has been made on the other side. My questions are: Is this link between networks a reliable infrastructure on which to set up DFS replication? What latency times would be typical (seconds, minutes, hours, days)? Would you recommend that we go for DFS in this scenario, or is there a better alternative? Many thanks.

  Read the article

• Can a pool of memcache daemons be used to share sessions more efficiently?

  - by Tom

  We are moving from a 1 webserver setup to a two webserver setup and I need to start sharing PHP sessions between the two load balanced machines. We already have memcached installed (and started) and so I was pleasantly surprized that I could accomplish sharing sessions between the new servers by changing only 3 lines in the php.ini file (the session.save_handler and session.save_path): I replaced: session.save_handler = files with: session.save_handler = memcache Then on the master webserver I set the session.save_path to point to localhost: session.save_path="tcp://localhost:11211" and on the slave webserver I set the session.save_path to point to the master: session.save_path="tcp://192.168.0.1:11211" Job done, I tested it and it works. But... Obviously using memcache means the sessions are in RAM and will be lost if a machine is rebooted or the memcache daemon crashes - I'm a little concerned by this but I am a bit more worried about the network traffic between the two webservers (especially as we scale up) because whenever someone is load balanced to the slave webserver their sessions will be fetched across the network from the master webserver. I was wondering if I could define two save_paths so the machines look in their own session storage before using the network. For example: Master: session.save_path="tcp://localhost:11211, tcp://192.168.0.2:11211" Slave: session.save_path="tcp://localhost:11211, tcp://192.168.0.1:11211" Would this successfully share sessions across the servers AND help performance? i.e save network traffic 50% of the time. Or is this technique only for failovers (e.g. when one memcache daemon is unreachable)? Note: I'm not really asking specifically about memcache replication - more about whether the PHP memcache client can peak inside each memcache daemon in a pool, return a session if it finds one and only create a new session if it doesn't find one in all the stores. As I'm writing this I'm thinking I'm asking a bit much from PHP, lol... Assume: no sticky-sessions, round-robin load balancing, LAMP servers.

  Read the article

• Debugging Windows PC freeze

  - by Violet Giraffe

  I have a problem with my computer, would appreciate any hints/ideas. It usually begins not immediately after booting Windows, but at some unpredictable point in time, which doesn't seem to correlate with any specific actions of mine. First sign of a problem is process System starting to consume 25% CPU time steadily. I have a quad-core CPU, so it might be one thread working non-stop. At this point micro-freezes start to occur - screen stops refreshing, but if I have, say, music player running - it continues playing. If I try to do something between the freezes, like open Start menu, it will freeze completely and forever. If I press reset button the PC will shut down and then start cold, as opposed to usual reset behavior (which doesn't include PC shutting down). I have noticed that full restart upon reset is usual for hardware problems, but I think this problem isn't related to at least motherboard-CPU-RAM-videoadapter. It certainly isn't caused by overheating. One very important not is that it seems to be related to Windows hosted WLAN network: I have USB Wi-Fi dongle and have configured a hosted network to share cable Internet connection with Wi-Fi devices. I am not 100% certain there's a strong connection, but in 9 or 10 cases when I enabled the network (by executing netsh wlan start hostednetwork), it did freeze eventually (sometimes within minutes of starting the network, sometimes within hours), and on at least 10 days when I didn't start the network it never froze, no matter how I used the computer). There are no critical/error entries in the events log that I can suspect as being related, only regular stuff like "driver not loaded". I have found no critical/error events that are being logged around the time of freeze occurring and are not logged during normal boot without starting the WLAN.

  Read the article

• How to stop scheduled chkdisk on windows 7?

  - by AndrejaKo

  Hi! I have a problem with windows 7 64-bit. I was trying out chkdsk command line options and scheduled a chddsk /r on next start. After that I disassembled the laptop on which I set the chkdsk. After I reassembled it, windows gets normally to the point where it should start the check and then hangs when the countdown reaches 1 second. During the countdown, it doesn't detect any input from keyboard. At first I thought that I didn't correctly install the keyboard, but under GNU/Linux, everything is working fine and I can normally mount the windows partition . So is there any way to stop the scheduled chkdsk? I really don't feel like reinstalling windows again because I just finished setting up my tool-chain the way I like it and compiled about 6GiB worth of dependencies I need for some project I'm working on.

  Read the article

• What does this diagnostic output mean?

  - by ChrisF

  I recently had a fault with my broadband connection. It turned out to be a fault with the ISP's or teleco's equipment. My ISP posted this diagnostic, but while I understand it in general, I'd like to to know more about the details. I'm assuming that ATM means Asynchronous Transfer Mode and PPP means Point to Point Protocol. It was this that my router was indicating as the fault. xDSL Status Test Summary Sync Status: Circuit In Sync General Information NTE Status: NTE Power Status: Unknown Bypass Status: Upstream DSL Link Information Downstream DSL Link Information Loop Loss: 9.0 17.0 SNR Margin: 25 15 Errored Seconds: 0 0 HEC Errors: 0 Cell Count: 0 0 Speed: 448 8128 TAM Status: Successfully executed operation Network Test: Sub-Test Results Layer Name Value Status Modem pass Transmitter Power (Upstream) 12.4 dBm Transmitter Power (Downstream) 8.8 dBm Upstream psd -38 dBm/Hz Downstream psd -51 dBm/Hz DSL pass Equipment Vendor Name TSTC Equipment Vendor Id n/a Equipment Vendor Revision n/a Training Time 8 s Num Syncs 1 Upstream bit rate 448 kbps Downstream bit rate 8128 kbps Upstream maximum bit rate 1108 kbps Downstream maximum bit rate 11744 kbps Upstream Attenuation 3.5 dB Downstream Attenuation 0.0 dB Upstream Noise Margin 20.0 dB Downstream Noise Margin 19.0 dB Local CRC Errors 0 Remote CRC Errors 0 Up Data Path interleaved Down Data Path interleaved Standard Used G_DMT INP INP Upstream Symbols n/a INP Upstream Delay 4 ms INP Upstream Depth 4 INP Downstream Symbols n/a INP Downstream Delay 5 ms INP Downstream Depth 32 ATM Reason: No ATM cells received fail Number of cells transmitted 30 Number of cells received 0 number of Near end HEC errors 0 number of Far end HEC errors n/a PPP Reason: No response from peer fail PAP authentication nottested CHAP authentication nottested (I'm not sure that Super User is the best place to ask this, but two people have suggested I ask it here so here I am).

  Read the article

• Installing Linux kernel 2.6.25.14 on RHEL 5.4

  - by aaron

  I have to install Linux kernel version 2.5.25.14 on a RHEL 5.4 server because of drive compatibility issues. I follow the RedHat "Building a Custom Kernel" instructions running the following: $ make mrproper $ make xconfig $ make clean $ make bzImage $ make modules $ make modules_install $ make install But I get a bunch of warnings like this: WARNING: No module ehci-hcd found for kernel 2.6.25.24, continuing anyway When I try to boot this kernel it is unable to mount the hard drive, and kernel panics on startup. As far as I can tell I'm using a standard configuration (I just accept the defaults and save a .config file). Is there something I'm missing? Thanks.

  Read the article

• Windows 7 boots to black screen with blinking cursor

  - by murgatroid99

  I have an Alienware M17x that dual boots into Ubuntu 11.04 and Windows 7 Home Premium. Currently, the computer starts at the GRUB loader and will boot into Ubuntu, but if I try to boot into Windows, I immediately get a black screen with a blinking cursor in the upper left corner. The output of fdisk -l is Device Boot Start End Blocks Id System /dev/dm-0p1 1 5 40131 de Dell Utility Partition 1 does not start on physical sector boundary. /dev/dm-0p2 6 1918 15360000 7 HPFS/NTFS Partition 2 does not start on physical sector boundary. /dev/dm-0p3 * 1918 64772 504878877+ 7 HPFS/NTFS Partition 3 does not start on physical sector boundary. /dev/dm-0p4 64772 77827 104858625 5 Extended Partition 4 does not start on physical sector boundary. /dev/dm-0p5 64772 67204 19531008 83 Linux /dev/dm-0p6 67204 74498 58593536 83 Linux /dev/dm-0p7 74498 77577 24731648 83 Linux /dev/dm-0p8 77578 77827 2000128 82 Linux swap / Solaris I have used the Windows rescue CD, and run the automatic error fixer until it finds no errors. I have run chkdsk /R on both the main Windows 7 (/dev/dm-0p3) partition and the recovery partition (/dev/dm-0p2). I set the main Windows 7 partition to be active. I also tried running in the recovery console the commands bootrec /fixmbr bootrec /fixboot bootrec /rebuildbcd None of these helped and the last set of commands deletes grub, which I then have to reinstall from Ubuntu. I think the last thing I did in windows before this started was install the newest ATI driver for my video card. This would suggest using system restore, and I actually had a restore point earlier (after the problem started), but after whatever I did that restore point does not appear in the list on the recovery disk any more, so I cannot do a system restore. Is there anything else I can try to make Windows boot properly again? Edit: Running the suggested commands bootsect /nt60 c: bcdboot c:\windows /s c: was also ineffective.

  Read the article

• How to automatically show USB camera or memory stick contents in Icewm?

  - by darenw

  I normally use a very lightweight Linux setup. No desktop like Gnome or KDE, just Icewm as the windows manager and nothing else that normal users might consider essential. Well, I do need a file manager - I use Thunar. Recently I've been trying Gnome. Whenever I shove a memory stick into a USB port, or connect my digital camera, it can automatically pop up a file manager showing all the goodies on that device. KDE does this too. I like this. Although quick at the command line, I like not having to go sudo to mount the device and all that. If I want to stick with a lightweight setup using Icewm+Thunar, is there something non-huge I can install to make external devices fire up a Thunar window, or otherwise make access to the contents brainlessly easy?

  Read the article

• Lightweight Live Linux Image

  - by MA1

  I am working on an application which is being developed in wxPython and C plus using linux core utilities and network support. To be more specific, I only need the following support for following packages/softwares/components. wxPython C Network Support Linux Utilities Vi File System(fdisk/parted, ntfsprogs etc) Basic(cp, mount/umount, mkdir etc) The application will run from a live CD. Currently i am using Fedora 12 with Gnome for live CD. Currently the size of live image is around 350 MB. The size of application is hardly 1 MB. I don't need anything else except above mentioned. Just my application and supporting packages, no desktop etc. So, I need a Lightweight Linux image as smaller as possible providing all the above mentioned packages/components. I am considering the following distributions: Xfce LXDE Fluxbox Enlightenment Any ideas/suggestions?

  Read the article

• My Windows 7 has suddenly stopped displaying Unicode symbols

  - by Felix Dombek

  For some strange reason, my computer suddenly doesn't show certain unicode characters anymore! I have no idea what happened. Affected applications include Windows Explorer (should be Japanese characters), Google Chrome (should be a heart), and Winamp (should be stars): Russian, German etc. characters are displayed normally. Chrome also displays Japanese script on websites, but not in the GUI. How can I fix it? Update: I have tried to use System Restore to fix it. I needed to go back in time quite a while because the most recent restore points didn't solve it so I used one from the middle of November. After that restore, Unicode symbols were displayed again. Then I updated my system with Windows Update again because those were removed during the restore. After that, the error occurred again! I then did a restore to a point before my new updates, but the error persists, and the old restore point (which I used before) is gone and there are currently no other snapshots of the system. Any suggestions on what to do now? Update 2: I could find a workaround: Control Panel ? Region and Language ? Administration ? Change Language for Unicode-incompatible programs to Japanese (Japan). All mentioned programs display their symbols correctly again. However, I don't consider this a fix because these programs are not usually Unicode-incompatible, and it also leads to some (non-serious) artifacts in some programs. I still welcome an answer that tells me what went wrong here and how to fix the issue.

  Read the article

• Dell Driver Support for Latitude E6320 Windows 7 Enterprise

  - by IamPolaris

  I recently did a reinstall of Windows 7 Enterprise on a Dell Latitude E6320, which is a 64 bit system. After the install process, and doing typical Windows Update stuff, I looked at my Device Manager and found that I had devices which were missing drivers. My missing drivers: After going to the Dell Support site and looking at the files, and doing some sleuthing I found the following support document: http://downloads.dell.com/utility/Latitude%20E-Family%20%20Mobile%20Precision%20Re-Image%20How-To%20Guide%20-%20A03%20Rev%203%200.pdf This document hints in appendix C that the Broadcom USH is the Control Point Security and the Unknown device is Micro freefall sensor. The network controller is my wireless, as I cannot connect wirelessly, and the final missing driver I am not sure. Attempting to install the control point security exe on the support page will not work. After downloading, I am given the message that I am attempting to install a 32 bit driver on a 64 bit machine EVEN THOUGH I selected the win7 64 bit option from the support page. Beyond that, some of the drivers (Which are confusing to read and hard to understand what they do) and the system utilities which are supposedly supposed to make this process simpler will either a) not run because they are 32 bit exe's or b) the support page cannot find the file attempted to download. Is there anything I can do to get (at the very least) my wireless running, but idealistically all of my drivers. A solution which assumes Dell is completely incompetent would be ideal. :P Some forums have said that I should download the chipset driver, others say to get the system utility file (DSS_UTIL_WIN_R282536.EXE). I have had no luck as of yet...

  Read the article

< Previous Page | 225 226 227 228 229 230 231 232 233 234 235 236  | Next Page >