Search Results

Search found 14011 results on 561 pages for 'interface orientation'.

Page 233/561 | < Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >

• dhcp-snooping option 82 drops valid dhcp requests on 2610 series Procurve switches

  - by kce

  We are slowly starting to implement dhcp-snooping on our HP ProCurve 2610 series switches, all running the R.11.72 firmware. I'm seeing some strange behavior where dhcp-request or dhcp-renew packets are dropped when originating from "downstream" switches due "untrusted relay information from client". The full error: Received untrusted relay information from client <mac-address> on port <port-number> In more detail we have a 48 port HP2610 (Switch A) and a 24 port HP2610 (Switch B). Switch B is "downstream" of Switch A by virtue of a DSL connection to one of Switch A ports. The dhcp server is connected to Switch A. The relevant bits are as follows: Switch A dhcp-snooping dhcp-snooping authorized-server 192.168.0.254 dhcp-snooping vlan 1 168 interface 25 name "Server" dhcp-snooping trust exit Switch B dhcp-snooping dhcp-snooping authorized-server 192.168.0.254 dhcp-snooping vlan 1 interface Trk1 dhcp-snooping trust exit The switches are set to trust BOTH the port the authorized dhcp server is attached to and its IP address. This is all well and good for the clients attached to Switch A, but the clients attached to Switch B get denied due to the "untrusted relay information" error. This is odd for a few reasons 1) dhcp-relay is not configured on either switch, 2) the Layer-3 network here is flat, same subnet. DHCP packets should not have a modified option 82 attribute. dhcp-relay does appear to be enabled by default however: SWITCH A# show dhcp-relay DHCP Relay Agent : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : append Remote ID : mac Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 0 0 0 0 SWITCH B# show dhcp-relay DHCP Relay Agent : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : append Remote ID : mac Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 40156 0 0 0 And interestingly enough the dhcp-relay agent seems very busy on Switch B, but why? As far as I can tell there is no reason why dhcp requests need a relay with this topology. And furthermore I can't tell why the upstream switch is dropping legitimate dhcp requests for untrusted relay information when the relay agent in question (on Switch B) isn't modifying the option 82 attributes anyway. Adding the no dhcp-snooping option 82 on Switch A allows the dhcp traffic from Switch B to be approved by Switch A, by virtue of just turning off that feature. What are the repercussions of not validating option 82 modified dhcp traffic? If I disable option 82 on all my "upstream" switches - will they pass dhcp traffic from any downstream switch regardless of that traffic's legitimacy? This behavior is client operating system agnostic. I see it with both Windows and Linux clients. Our DHCP servers are either Windows Server 2003 or Windows Server 2008 R2 machines. I see this behavior regardless of the DHCP servers' operating system. Can anyone shed some light on what's happening here and give me some recommendations on how I should proceed with configuring the option 82 setting? I feel like i just haven't completely grokked dhcp-relaying and option 82 attributes.

  Read the article

• How can I run supervisord without using root?

  - by Jason Baker

  I seem to be having trouble figuring out why supervisord won't run as a non-root user. If I start it with the user set to jason (pid 1000), I get the following in the log file: 2010-05-24 08:53:32,143 CRIT Set uid to user 1000 2010-05-24 08:53:32,143 WARN Included extra file "/home/jason/src/tsched/celeryd.conf" during parsing 2010-05-24 08:53:32,189 INFO RPC interface 'supervisor' initialized 2010-05-24 08:53:32,189 WARN cElementTree not installed, using slower XML parser for XML-RPC 2010-05-24 08:53:32,189 CRIT Server 'unix_http_server' running without any HTTP authentication checking 2010-05-24 08:53:32,190 INFO daemonizing the supervisord process 2010-05-24 08:53:32,191 INFO supervisord started with pid 3444 ...then the process dies for some unknown reason. If I start it without sudo (under the user jason), I get similar output: 2010-05-24 08:51:32,859 INFO supervisord started with pid 3306 2010-05-24 08:52:15,761 CRIT Can't drop privilege as nonroot user 2010-05-24 08:52:15,761 WARN Included extra file "/home/jason/src/tsched/celeryd.conf" during parsing 2010-05-24 08:52:15,807 INFO RPC interface 'supervisor' initialized 2010-05-24 08:52:15,807 WARN cElementTree not installed, using slower XML parser for XML-RPC 2010-05-24 08:52:15,807 CRIT Server 'unix_http_server' running without any HTTP authentication checking 2010-05-24 08:52:15,808 INFO daemonizing the supervisord process 2010-05-24 08:52:15,809 INFO supervisord started with pid 3397 ...and it still doesn't run. If it's any help, here's the supervisord.conf file I'm using: [unix_http_server] file=/tmp/supervisor.sock ; path to your socket file [supervisord] logfile=./supervisord.log ; supervisord log file logfile_maxbytes=50MB ; maximum size of logfile before rotation logfile_backups=10 ; number of backed up logfiles loglevel=debug ; info, debug, warn, trace pidfile=./supervisord.pid ; pidfile location nodaemon=false ; run supervisord as a daemon minfds=1024 ; number of startup file descriptors minprocs=200 ; number of process descriptors user=jason ; default user childlogdir=./supervisord/ ; where child log files will live [rpcinterface:supervisor] supervisor.rpcinterface_factory = supervisor.rpcinterface:make_main_rpcinterface [supervisorctl] serverurl=unix:///tmp/supervisor.sock ; use unix:// schem for a unix sockets. [include] # Uncomment this line for celeryd for Python files=celeryd.conf # Uncomment this line for celeryd for Django. ;files=django/celeryd.conf ...and here's celeryd.conf: [program:celery] command=bin/celeryd --loglevel=INFO --logfile=./celeryd.log environment=PYTHONPATH='./tsched_worker', JIVA_DB_PLATFORM='oracle', ORACLE_HOME='/usr/lib/oracle/xe/app/oracle/product/10.2.0/server', LD_LIBRARY_PATH='/usr/lib/oracle/xe/app/oracle/product/10.2.0/server/lib', TNS_ADMIN='/home/jason', CELERY_CONFIG_MODULE='tsched_worker.celeryconfig' directory=. user=jason numprocs=1 stdout_logfile=/var/log/celeryd.log stderr_logfile=/var/log/celeryd.log autostart=true autorestart=true startsecs=10 ; Need to wait for currently executing tasks to finish at shutdown. ; Increase this if you have very long running tasks. stopwaitsecs = 600 ; if rabbitmq is supervised, set its priority higher ; so it starts first priority=998 Can anyone help me figure out what's going on?

  Read the article

• Powering-down USB Powered Devices on laptop sleep

  - by Carl

  I recently purchased a Targus Lap Chill Mat, which is a USB powered device, but doesn't have any interface/storage/etc function. I'd like it to power-down when my (macbook) laptop sleeps (since the fan obviously doesn't need to be running when the laptop is idle) without having to unplug it. Any suggestions?

  Read the article

• Windows Update for auto-complete filename in Explorer

  - by Stan

  OS: Windows XP SP3 Seems there is a Windows Update improves Explorer interface, adding auto-complete filename feature in open file dialogue, and when press F2 to rename file, the cursor will at filename(cursor here).txt instead of old way - filename.txt(cursor here). Does anyone know which update should I download? Thanks.

  Read the article

• Disk is spinning down each minute, unable to disable it

  - by lzap

  I played with spindown and APM settings of my Samsung discs and now they spin down every minute. I want to disable it, but it seems it does not accept any of the spindown time or APM values. Nothing works, it's all the same. Please help what values should be proper for it. I do not want it to spin down at all. /dev/sda: ATA device, with non-removable media Model Number: SAMSUNG HD154UI Serial Number: S1Y6J1KZ206527 Firmware Revision: 1AG01118 Standards: Used: ATA-8-ACS revision 3b Supported: 7 6 5 4 Configuration: Logical max current cylinders 16383 16383 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 16514064 LBA user addressable sectors: 268435455 LBA48 user addressable sectors: 2930277168 Logical/Physical Sector size: 512 bytes device size with M = 1024*1024: 1430799 MBytes device size with M = 1000*1000: 1500301 MBytes (1500 GB) cache/buffer size = unknown Capabilities: LBA, IORDY(can be disabled) Queue depth: 32 Standby timer values: spec'd by Standard, no device specific minimum R/W multiple sector transfer: Max = 16 Current = 16 Advanced power management level: 60 Recommended acoustic management value: 254, current value: 0 DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 udma7 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * SMART feature set Security Mode feature set * Power Management feature set * Write cache * Look-ahead * Host Protected Area feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * DOWNLOAD_MICROCODE * Advanced Power Management feature set Power-Up In Standby feature set * SET_FEATURES required to spinup after power up SET_MAX security extension Automatic Acoustic Management feature set * 48-bit Address feature set * Device Configuration Overlay feature set * Mandatory FLUSH_CACHE * FLUSH_CACHE_EXT * SMART error logging * SMART self-test Media Card Pass-Through * General Purpose Logging feature set * 64-bit World wide name * WRITE_UNCORRECTABLE_EXT command * {READ,WRITE}_DMA_EXT_GPL commands * Segmented DOWNLOAD_MICROCODE * Gen1 signaling speed (1.5Gb/s) * Gen2 signaling speed (3.0Gb/s) * Native Command Queueing (NCQ) * Host-initiated interface power management * Phy event counters * NCQ priority information DMA Setup Auto-Activate optimization Device-initiated interface power management * Software settings preservation * SMART Command Transport (SCT) feature set * SCT Long Sector Access (AC1) * SCT LBA Segment Access (AC2) * SCT Error Recovery Control (AC3) * SCT Features Control (AC4) * SCT Data Tables (AC5) Security: Master password revision code = 65534 supported not enabled not locked frozen not expired: security count supported: enhanced erase 326min for SECURITY ERASE UNIT. 326min for ENHANCED SECURITY ERASE UNIT. Logical Unit WWN Device Identifier: 50024e900300cca3 NAA : 5 IEEE OUI : 0024e9 Unique ID : 00300cca3 Checksum: correct I have the very same disc which I did not "tuned" and it does not spin. But I do not know where to read the settings from. The hdparm only shows this: Advanced power management level: 60 Recommended acoustic management value: 254, current value: 0 Edit: It seems the issue was tuned daemon in RHEL6. It was too aggressive, I turned off disc tuning and it seems they are no longer spinning down.

  Read the article

• netsh add profile returns "An attempt was made to load a program with an incorrect format."

  - by Tunisia

  Using netsh, I used the following command to add a wireless profile add profile filename="c:\profiles\DLINK-Profile.xml" interface="D-Link DWA-125 N150" All parameters are valid. But I get the error "An attempt was made to load a program with an incorrect format." I know this error is related to OS architecture 64bit or 32 bit. But i'm not sure which program is not compatible. I'm using Win7 64bit

  Read the article

• How to set up a mini call center?

  - by Ralph

  I'm trying to figure out how to set up a miniature call center for a small business. Like, for 1-4 people to take calls, but hopefully expandable to more. We want to accept nation-wide calls, and then I guess distribute the calls among the available agents. If no one is available, I guess it should either put them in a queue and play some annoying music for them, or forward to call to an agent who has least-recently taken a call who can then quickly answer and say "please hold" until they're done their call. We want to have one phone number that customers can call. I guess we then need some kind of ACD system which would take each call and forward it to an agent based on some algorithm? Then we would need to purchase a separate phone line for each agent, plus one just for the distributor? Or do we need several "extra" lines to maintain a queue (one for each customer waiting too)? This "ACD" thing, is it just a device that you would plug a phone line into (or several?), and maybe connect to a computer, aided by some software? Or is a subscription thing that I would need from my local telephone provider? Next, the business we're running, the callers will be repeat customers. It would be helpful to automatically pull up their profile based on the incoming number. The "software" our agents will be running will just be a website where they can log in (preferably from home) and then enter some information they would obtain through the call. So, the system would have to somehow interface with the website if possible. If not, we'll just have to ask each customer for an identifier (phone number, username, customer number, or something). Is this possible? I guess each computer would need a device that the call would pass through, and then if I can somehow hook into that, then I can write some software that will interface with the site. So, where do I start? What hardware do we need to buy? What subscriptions do we need? We were thinking this magicJack might help us in accepting long-distance calls for cheaper, but my understanding is that they provide you with some weird-looking number, is there a way we could "mask" it with our toll-free number? And then pass the incoming calls through the distributor system, which would then get passed to the call-accepting device which would both allow an agent to answer the call and have a software hook? (I realize this might be partially out of the scope of SU, but I wasn't sure where else to ask. It is about computer(-aided) hardware and software anyway.) P.S.: I don't need any of that "press 1 to talk to..." or "say xyz to..." junk. Just a straight-forward, connect-to-next-available-agent system.

  Read the article

• How to get ASUS UEFI BIOS EZ Mode utility on my asus laptop?

  - by Manoj Kumar

  i have asus laptop with the following specs: Manufacturer ASUSTeK Computer Inc. Model K53SC (CPU 1) Version 1.0 Chipset Vendor IntelBIOS Brand American Megatrends Inc. Version K53SC.208 Chipset Model Sandy Bridge BIOS Brand American Megatrends Inc. Version K53SC.208 Operating System MS Windows 7 Ultimate 64-bit In the BIOS setting i have enabled 'UEFI' but im not unable to see the graphical interface of UEFI.

  Read the article

• Fan speed monitor Software for Macbook Pro Unibody on Windows

  - by dtmunir

  I've tried multiple temperature monitor and fan speed software on my Macbook Pro Unibody under Windows 7 64-bit RC. None of them can report the fan speed. Currently I'm using SpeedFan which reports the CPU temperature of each of the two cores, but is not able to detect or interface with the Fans. Has anyone had any luck with this?

  Read the article

• Supervisor sentry-web exit status 1

  - by rockingskier

  I'm having problems getting Sentry (https://www.getsentry.com - not enough rep for a link) running as a service using supervisor. I can run Sentry in the command line and view it correctly in the browser but when it comes to supervisor I am completely in the dark. I shall try and give all the details I can Initial user warning By no means a server admin, just playing/learning in VirtualBox. Literally only just discovered supervisor from reading the Sentry documentation so I may well be making some obvious mistakes here. The setup: Ubuntu server 11.10 (fresh install, VirtualBox) virtualenv with Sentry and its dependencies. supervisor Instructions followed Supervisor with vanilla ini file Sentry/supervisor instructions My supervisor ini (Sentry section) [program:sentry-web] directory=/root/.virtualenvs/sentry/ command= start http /root/.virtualenvs/sentry/bin/sentry autostart=true autorestart=true redirect_stderr=true OK so here we go: When I run supervisord -n I get the following messages rather than a nice web interface to play with. 2012-04-12 23:48:09,024 CRIT Supervisor running as root (no user in config file) 2012-04-12 23:48:09,097 INFO RPC interface 'supervisor' initialized 2012-04-12 23:48:09,099 CRIT Server 'unix_http_server' running without any HTTP authentication checking 2012-04-12 23:48:09,100 INFO supervisord started with pid 17813 2012-04-12 23:48:10,126 INFO spawned: 'sentry-web' with pid 17816 2012-04-12 23:48:10,169 INFO exited: sentry-web (exit status 1; not expected) 2012-04-12 23:48:11,199 INFO spawned: 'sentry-web' with pid 17817 2012-04-12 23:48:11,238 INFO exited: sentry-web (exit status 1; not expected) 2012-04-12 23:48:13,269 INFO spawned: 'sentry-web' with pid 17818 2012-04-12 23:48:13,309 INFO exited: sentry-web (exit status 1; not expected) 2012-04-12 23:48:16,343 INFO spawned: 'sentry-web' with pid 17819 2012-04-12 23:48:16,389 INFO exited: sentry-web (exit status 1; not expected) 2012-04-12 23:48:17,394 INFO gave up: sentry-web entered FATAL state, too many start retries too quickly CRIT Supervisor running as root (no user in config file) suggests a big problem, probably shouldn't be running this as root? CRIT Server 'unix_http_server' running without any HTTP authentication checking Surely authentication is optional? INFO exited: sentry-web (exit status 1; not expected) *sad face* here. Google hasn't been much help yet. Anyway, that is it as far as I know. If anyone can help me that would be greatly appreciated. Thanks in advance.

  Read the article

• Downloading image from Picasa Web Albums loses metadata

  - by Jarrod

  I have several photos on my Picasa Web Albums account. I have added captions, tags and location information to many of them through the PWA web interface. I assumed that PWA was saving this information in an IPTC, or some other metadata tag inside the image, but whenever I go to 'Download Photo' (on a single image), the resulting image, when saved to my computer, has no tags whatsoever. Does anybody know why this is the case? Does PWA require Picasa to be installed to preserve this information?

  Read the article

• MediaWiki on MS Sql Server

  - by kdbolt70

  Hello all, I've been doing some digging on running mediawiki on sql server instead of mySQL, but haven't come across any concrete information. All of our servers are running SQL Server so I'd like to stick with that. I've tried Screwturn wiki, which is an ASP.NET wiki implementation using SQL Server, but I'm not terribly happy with the editing interface, and would really like to get MediaWiki up and running. Does anyone know if this is possible? Thanks!

  Read the article

• Command line FTPS ?

  - by user32810

  I need to write a batch file to auto upload a backup every day. I'm restricted to windows, can anyone suggest any free software to do this? I was looking at Filezilla, the command line interface doesn't let you auto upload files and I need to buy a license for CuteFTP. Thanks, Teja

  Read the article

• openstack, bridging, netfilter and dnat

  - by Craig Sanders

  In a recent upgrade (from Openstack Diablo on Ubuntu Lucid to Openstack Essex on Ubuntu Precise), we found that DNS packets were frequently (almost always) dropped on the bridge interface (br100). For our compute-node hosts, that's a Mellanox MT26428 using the mlx4_en driver module. We've found two workarounds for this: Use an old lucid kernel (e.g. 2.6.32-41-generic). This causes other problems, in particular the lack of cgroups and the old version of the kvm and kvm_amd modules (we suspect the kvm module version is the source of a bug we're seeing where occasionally a VM will use 100% CPU). We've been running with this for the last few months, but can't stay here forever. With the newer Ubuntu Precise kernels (3.2.x), we've found that if we use sysctl to disable netfilter on bridge (see sysctl settings below) that DNS started working perfectly again. We thought this was the solution to our problem until we realised that turning off netfilter on the bridge interface will, of course, mean that the DNAT rule to redirect VM requests for the nova-api-metadata server (i.e. redirect packets destined for 169.254.169.254:80 to compute-node's-IP:8775) will be completely bypassed. Long-story short: with 3.x kernels, we can have reliable networking and broken metadata service or we can have broken networking and a metadata service that would work fine if there were any VMs to service. We haven't yet found a way to have both. Anyone seen this problem or anything like it before? got a fix? or a pointer in the right direction? Our suspicion is that it's specific to the Mellanox driver, but we're not sure of that (we've tried several different versions of the mlx4_en driver, starting with the version built-in to the 3.2.x kernels all the way up to the latest 1.5.8.3 driver from the mellanox web site. The mlx4_en driver in the 3.5.x kernel from Quantal doesn't work at all) BTW, our compute nodes have supermicro H8DGT motherboards with built-in mellanox NIC: 02:00.0 InfiniBand: Mellanox Technologies MT26428 [ConnectX VPI PCIe 2.0 5GT/s - IB QDR / 10GigE] (rev b0) we're not using the other two NICs in the system, only the Mellanox and the IPMI card are connected. Bridge netfilter sysctl settings: net.bridge.bridge-nf-call-arptables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-ip6tables = 0 Since discovering this bridge-nf sysctl workaround, we've found a few pages on the net recommending exactly this (including Openstack's latest network troubleshooting page and a launchpad bug report that linked to this blog-post that has a great description of the problem and the solution)....it's easier to find stuff when you know what to search for :), but we haven't found anything on the DNAT issue that it causes.

  Read the article

• Confusion on networking service start/stop in Ubuntu

  - by Daniel Ball

  I'm preparing to move and took down two of my servers, leaving only one with some essential services running. What I neglected to consider was that one was the DHCP server(which I realized when somebody contacted me saying they couldn't connect. Whups). So because I only have a few hosts on this small network, I opted to just statically configure them for now. One of these is a new Ubuntu 11.04 server, where I have very little experience. I edited /etc/network/interfaces and /etc/hosts to reflect my changes. I ran $sudo /etc/init.d/networking stop *deconfiguring network interfaces ... So yay. Then I try to start, it gives me the mumbo jumbo about using services (why didn't it do that for the stop?) So instead I run ... $sudo service networking start networking stop/waiting Now, to me that says the status of the service is stopped. But when I ping another computer, I get a successful reply. So is it not actually stopped? More importantly, am I doing something wrong? Edit daniel@FOOBAR:~$ sudo service networking status networking stop/waiting daniel@FOOBAR:~$ sudo service networking stop stop: Unknown instance: daniel@FOOBAR:~$ sudo service networking status networking stop/waiting daniel@FOOBAR:~$ sudo service networking start networking stop/waiting daniel@FOOBAR:~$ sudo service networking status networking stop/waiting So you can see why I ran /etc/init.d/networking stop instead. For some reason upstart (that is what "services" is, right?) isn't working with stop. cat /etc/hosts 127.0.0.1 localhost 127.0.1.1 FOOBAR 198.3.9.2 FOOBAR #Added entry July 19 2011 # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters cat /etc/network/interfaces # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface #auto eth0 #iface eth0 inet dhcp # hostname FOOBAR auto eth0 iface eth0 inet static address 198.3.9.2 netmask 255.255.255.0 network 198.3.9.0 broadcast 198.3.9.255 gateway 198.3.9.15 No I didn't save backups, it was just a minor change so I just commented out the old DHCP setting. Edit I set everything back to original settings and set up a DHCP server. "starting" networking does the same thing. I can only assume this is normal, I just don't know WHY. It can't be anything to do with the configuration files, since they've been restored.

  Read the article

• Squid 2.7.STABLE3-4.1 as a transparent proxy on Ubuntu Server 9.04

  - by E3 Group

  Can't get this to work at all! I'm trying to get this linux box to act as a transparent proxy and, with the help of DHCP, force everyone on the network to gate into the proxy. I have two ethernet connections, both to the same switch. And I'm trying to get 192.168.1.234 to become the default gateway. The actual WAN connection is to a gateway 192.168.1.1. eth0 is 192.168.1.234 eth1 is 192.168.1.2 Effectively I'm trying to make eth0 a LAN only interface and eth1 a WAN interface. I've oi should set the gateway for eth1 to point to 192.168.1.234 my squid.conf file has the following directives added at the bottom: nly set eth0 to have a gateway address in /etc/network/interfaces I'm not sure whether http_port 3128 transparent acl lan src 192.168.1.0/24 acl lh src 127.0.0.1/255.255.255.0 http_access allow lan http_access allow lh i've added the following routing commands: iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.1.2:3128 iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 I set a computer with TCP settings 192.168.1.234 as the gateway and opened up google.com, but it comes up with a request error. Any ideas why this isn't working? :( Been searching continuously for a solution to no avail. ----------------------------- EDIT ------------------------------- Managed to get it to route properly to the squid, here's the error I get in the browser: ERROR The requested URL could not be retrieved While trying to process the request: GET / HTTP/1.1 Host: www.google.com User-Agent: Mozilla/5.0 (Windows; U; Windows NT 5.1; en-GB; rv:1.9.1.2) Gecko/20090729 Firefox/3.5.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-gb,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive Cache-Control: max-age=0 The following error was encountered: * Invalid Request Some aspect of the HTTP Request is invalid. Possible problems: * Missing or unknown request method * Missing URL * Missing HTTP Identifier (HTTP/1.0) * Request is too large * Content-Length missing for POST or PUT requests * Illegal character in hostname; underscores are not allowed Your cache administrator is webmaster. Generated Mon, 26 Oct 2009 03:41:15 GMT by mjolnir.lloydharrington.local (squid/2.7.STABLE3)

  Read the article

• Rackspace Cloud Server DNS Add SPF Records

  - by user625435

  I've setup my new LAMP server on Rackspace Cloud and the Basic A, C and MX DNS setup is no problem. I need to add an SPF record for a project I am migrating over to this new server that allows emails from a 3rd party server and I can't seem to figure out how to do this. There doesn't seem to be an option to add a TXT record in my Rackspace Cloud Server interface and I installed the BIND DNS on my Apache server, but I am not sure how to get that to been seen, etc.

  Read the article

• method to change apache config via the shell with whm/cpanel

  - by Chiggsy

  How can I make changes to the apache config on a whm/cpanel setup from the shell and have them integrate properly? I read the theory of the config system and regardless of my feelings on the matter I understand where they are coming from. Still, in that world view, there must be a way to interact with the system from a command line interface, right?

  Read the article

• Change iPhone MAC address

  - by Freeman

  Hello, is it possible to change the iPhone MAC address? I have used ifconfig [interface] ether 01:02:03:04:05:06, but the MAC address does not change. Perhaps Apple has disabled the corresponding sysctl and it is necessary to patch the kernel.

  Read the article

• Autologin on Ubuntu Server

  - by hekevintran

  I have a machine running Ubuntu Server. It has only a command-line interface. How can I make the system login with a specific user automatically (I don't want to type the username/password). I know that this is insecure and I don't care.

  Read the article

• Manage Internet connection for a program

  - by michel

  I am using a Windows 7 PC with 2 network cards. One for a public line and one for an internal line behind a proxy. Is there a way or a software program where I can manage which program (Outlook, WM) uses which Internet connection or network card? Using the option of interface metric is not what I am looking for. Someone also suggested me ZoneAlarm, but I dislike this program.

  Read the article

• External USB attached drive works in Windows XP but not in Windows 7. How to fix?

  - by irrational John

  Earlier this week I purchased this "N52300 EZQuest Pro" external hard drive enclosure from here. I can connect the enclosure using USB 2.0 and access the files in both NTFS partitions on the MBR partitioned drive when I use either Windows XP (SP3) or Mac OS X 10.6. So it works as expected in XP & Snow Leopard. However, the enclosure does not work in Windows 7 (Home Premium) either 64-bit or 32-bit or in Ubuntu 10.04 (kernel 2.6.32-23-generic). I'm thinking this must be a Windows 7 driver problem because the enclosure works in XP & Snow Leopard. I do know that no special drivers are required to use this enclosure. It is supported using the USB mass storage drivers included with XP and OS X. It should also work fine using the mass storage support in Windows 7, no? FWIW, I have also tried using 32-bit Windows 7 on both my desktop, a Gigabyte GA-965P-DS3 with a Pentium Dual-Core E6500 @ 2.93GHz, and on my early 2008 MacBook. I see the same failure in both cases that I see with 64-bit Windows 7. So it doesn't appear to be specific to one hardware platform. I'm hoping someone out there can help me either get the enclosure to work in Windows 7 or convince me that the enclosure hardware is bad and should be RMAed. At the moment though an RMA seems pointless since this appears to be a (Windows 7) device driver problem. I have tried to track down any updates to the mass storage drivers included with Windows 7 but have so far come up empty. Heck, I can't even figure out how to place a bug report with Microsoft since apparently the grace period for Windows 7 email support is only a few months. I came across a link to some USB troubleshooting steps in another question. I haven't had a chance to look over the suggestions on that site or try them yet. Maybe tomorrow if I have time ... ;-) I'll finish up with some more details about the problem. When I connect the enclosure using USB to Windows 7 at first it appears everything worked. Windows detects the drive and installs a driver for it. Looking in Device Manager there is an entry under the Hard Drives section with the title, Hitachi HDT721010SLA360 USB Device. When you open Windows Disk Management the first time after the enclosure has been attached the drive appears as "Not initialize" and I'm prompted to initialize it. This is bogus. After all, the drive worked fine in XP so I know it has already been initialized, partitioned, and formatted. So of course I never try to initialize it "again". (It's a 1 GB drive and I don't want to lose the data on it). Except for this first time, the drive never shows up in Disk Management again unless I uninstall the Hitachi HDT721010SLA360 USB Device entry under Hard Drives, unplug, and then replug the enclosure. If I do that then the process in the previous paragraph repeats. In Ubuntu the enclosure never shows up at all at the file system level. Below are an excerpt from kern.log and an excerpt from the result of lsusb -v after attaching the enclosure. It appears that Ubuntu at first recongnizes the enclosure and is attempting to attach it, but encounters errors which prevent it from doing so. Unfortunately, I don't know whether any of this info is useful or not. excerpt from kern.log [ 2684.240015] usb 1-2: new high speed USB device using ehci_hcd and address 22 [ 2684.393618] usb 1-2: configuration #1 chosen from 1 choice [ 2684.395399] scsi17 : SCSI emulation for USB Mass Storage devices [ 2684.395570] usb-storage: device found at 22 [ 2684.395572] usb-storage: waiting for device to settle before scanning [ 2689.390412] usb-storage: device scan complete [ 2689.390894] scsi 17:0:0:0: Direct-Access Hitachi HDT721010SLA360 ST6O PQ: 0 ANSI: 4 [ 2689.392237] sd 17:0:0:0: Attached scsi generic sg7 type 0 [ 2689.395269] sd 17:0:0:0: [sde] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 2689.395632] sd 17:0:0:0: [sde] Write Protect is off [ 2689.395636] sd 17:0:0:0: [sde] Mode Sense: 11 00 00 00 [ 2689.395639] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.412003] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.412009] sde: sde1 sde2 [ 2689.455759] sd 17:0:0:0: [sde] Assuming drive cache: write through [ 2689.455765] sd 17:0:0:0: [sde] Attached SCSI disk [ 2692.620017] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2707.740014] usb 1-2: device descriptor read/64, error -110 [ 2722.970103] usb 1-2: device descriptor read/64, error -110 [ 2723.200027] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2738.320019] usb 1-2: device descriptor read/64, error -110 [ 2753.550024] usb 1-2: device descriptor read/64, error -110 [ 2753.780020] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2758.810147] usb 1-2: device descriptor read/8, error -110 [ 2763.940142] usb 1-2: device descriptor read/8, error -110 [ 2764.170014] usb 1-2: reset high speed USB device using ehci_hcd and address 22 [ 2769.200141] usb 1-2: device descriptor read/8, error -110 [ 2774.330137] usb 1-2: device descriptor read/8, error -110 [ 2774.440069] usb 1-2: USB disconnect, address 22 [ 2774.440503] sd 17:0:0:0: Device offlined - not ready after error recovery [ 2774.590023] usb 1-2: new high speed USB device using ehci_hcd and address 23 [ 2789.710020] usb 1-2: device descriptor read/64, error -110 [ 2804.940020] usb 1-2: device descriptor read/64, error -110 [ 2805.170026] usb 1-2: new high speed USB device using ehci_hcd and address 24 [ 2820.290019] usb 1-2: device descriptor read/64, error -110 [ 2835.520027] usb 1-2: device descriptor read/64, error -110 [ 2835.750018] usb 1-2: new high speed USB device using ehci_hcd and address 25 [ 2840.780085] usb 1-2: device descriptor read/8, error -110 [ 2845.910079] usb 1-2: device descriptor read/8, error -110 [ 2846.140023] usb 1-2: new high speed USB device using ehci_hcd and address 26 [ 2851.170112] usb 1-2: device descriptor read/8, error -110 [ 2856.300077] usb 1-2: device descriptor read/8, error -110 [ 2856.410027] hub 1-0:1.0: unable to enumerate USB device on port 2 [ 2856.730033] usb 3-2: new full speed USB device using uhci_hcd and address 11 [ 2871.850017] usb 3-2: device descriptor read/64, error -110 [ 2887.080014] usb 3-2: device descriptor read/64, error -110 [ 2887.310011] usb 3-2: new full speed USB device using uhci_hcd and address 12 [ 2902.430021] usb 3-2: device descriptor read/64, error -110 [ 2917.660013] usb 3-2: device descriptor read/64, error -110 [ 2917.890016] usb 3-2: new full speed USB device using uhci_hcd and address 13 [ 2922.911623] usb 3-2: device descriptor read/8, error -110 [ 2928.051753] usb 3-2: device descriptor read/8, error -110 [ 2928.280013] usb 3-2: new full speed USB device using uhci_hcd and address 14 [ 2933.301876] usb 3-2: device descriptor read/8, error -110 [ 2938.431993] usb 3-2: device descriptor read/8, error -110 [ 2938.540073] hub 3-0:1.0: unable to enumerate USB device on port 2 excerpt from lsusb -v Bus 001 Device 017: ID 0dc4:0000 Macpower Peripherals, Ltd Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x0dc4 Macpower Peripherals, Ltd idProduct 0x0000 bcdDevice 0.01 iManufacturer 1 EZ QUEST iProduct 2 USB Mass Storage iSerial 3 220417 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 5 Config0 bmAttributes 0xc0 Self Powered MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 4 Interface0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Update: Results using Firewire to connect. Today I recieved a 1394b 9 pin to 1394a 6 pin cable which allowed me to connect the "EZQuest Pro" via Firewire. Everything works. When I use Firewire I can connect whether I'm using Windows 7 or Ubuntu 10.04. I even tried booting my Gigabyte desktop as an OS X 10.6.3 Hackintosh and it worked there as well. (Though if I recall correctly, it also worked when using USB 2.0 and booting OS X on the desktop. Certainly it works with USB 2.0 and my MacBook.) I believe the firmware on the device is at the latest level available, v1.07. I base this on the excerpt below from the OS X System Profiler which shows Firmware Revision: 0x107. Bottom line: It's nice that the enclosure is actually usable when I connect with Firewire. But I am still searching for an answer as to why it does not work correctly when using USB 2.0 in Windows 7 (and Ubuntu ... but really Windows 7 is my biggest concern). OXFORD IDE Device 1: Manufacturer: EZ QUEST Model: 0x0 GUID: 0x1D202E0220417 Maximum Speed: Up to 800 Mb/sec Connection Speed: Up to 400 Mb/sec Sub-units: OXFORD IDE Device 1 Unit: Unit Software Version: 0x10483 Unit Spec ID: 0x609E Firmware Revision: 0x107 Product Revision Level: ST6O Sub-units: OXFORD IDE Device 1 SBP-LUN: Capacity: 1 TB (1,000,204,886,016 bytes) Removable Media: Yes BSD Name: disk3 Partition Map Type: MBR (Master Boot Record) S.M.A.R.T. status: Not Supported

  Read the article

• Snort network instruction Mac OS X

  - by Rasatavohary

  I'm trying to learn network intrusion detection. When I try to launch Snort, in IDS mode, I get this message (I'm running Mac OS X): Initializing Network Interface en1 ERROR: OpenPcap() FSM compilation failed: syntax error PCAP command: snort Fatal Error, Quitting.. How can I fix this problem?

  Read the article

• Login configuration script for Junos EX 2200 using minicom

  - by liv2hak

  I am connecting to Junos OS on Juniper EX-2200 switches using minicom as shown below minicom -C log_sw1 sw1 Now I have a series of commands that I need to execute on sw1.(example shown below) cli request system zeroize show config show interface edit delete protocols set system arp aging-timer 240 I want to avoid having to type these commands every time I log into the system.I want to put them in a config file and I want the it to be execute every time I log into the switch using minicom. Is there any way I can achieve this?

  Read the article

• Microsoft Visio missing shape templates

  - by Rolnik

  I'm using MS Visio 2003 Standard. When I first was using it 3 years ago, it would let you search a database of thousands of ready-made templates, which I think Microsoft hosted at their own website. Several months ago, these templates were no longer available. I'm looking for some kind of replacement for common computer architecture and digital circuits, as well as user interface mock-ups. Does anybody know where I can find an assortment of these 'shapes'?

  Read the article

< Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >