Search Results

Search found 12061 results on 483 pages for 'non printable'.

Page 233/483 | < Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >

• S.M.A.R.T - Predictive Failure Count

  - by Bastien974

  I'm monitoring my IBM ServeRAID M5015 controller for RAID status with MegaCLI, I have this on one of the disk : Enclosure Device ID: 252 Slot Number: 6 Enclosure position: 0 Device Id: 14 Sequence Number: 2 Media Error Count: 32 Other Error Count: 0 Predictive Failure Count: 18 Last Predictive Failure Event Seq Number: 8119 PD Type: SAS Raw Size: 279.396 GB [0x22ecb25c Sectors] Non Coerced Size: 278.896 GB [0x22dcb25c Sectors] Coerced Size: 278.464 GB [0x22cee000 Sectors] Firmware state: Online, Spun Up SAS Address(0): 0x5000c50042c319c9 SAS Address(1): 0x0 Connected Port Number: 5(path0) Inquiry Data: IBM-ESXSST9300653SS B6336XN04HC10525B633 IBM FRU/CRU: 81Y9671 FDE Capable: Not Capable FDE Enable: Disable Secured: Unsecured Locked: Unlocked Needs EKM Attention: No Foreign State: None Device Speed: 6.0Gb/s Link Speed: 6.0Gb/s Media Type: Hard Disk Device Drive: Not Certified Drive Temperature :33 Celsius What does this mean exactly ? I can't find an exact description, is there a way to have more details ? The RAID array has the Optimal state. Media Error Count: 32 Predictive Failure Count: 18 Is there a way through the CLI to power-on the front LED so I physically know which disk I need to replace ?

  Read the article

• What are the quality metrics for RAM?

  - by Hi-Tech KitKat Android

  I have searched RAM and i found there are given some specification for the same capacity RAM, What are the difference and performance comparison between these? Like RAM1 General Brand Transcend Memory Type 2 GB (8 x 128 MB) DDR2 DIMM Memory Standard DDR2-800/PC-6400 Compatible Device PC Pins 240-pin Burst Length 4, 8 Buffered/Unbuffered Unbuffered Memory Memory Clock 400 MHz Technology DDR2 SDRAM Memory CAS Latency 4, 5, 6 RAM 2 General Brand Transcend Memory Type 2 GB (8 x 128 MB) DDR2 DIMM Memory Standard DDR2-667/PC2-5300 Compatible Device PC Pins 240-pin Burst Length 4, 8 Buffered/Unbuffered Unbuffered Memory Memory Clock 333 MHz Technology DDR2 SDRAM Memory CAS Latency 3, 4, 5 RAM3 General Brand Kingston Memory Type 2 GB (64 x 256 MB) 800 MHz DDR2 DIMM Compatible Device PC Pins 240-pin Error Check Non-ECC Buffered/Unbuffered Unbuffered Memory Memory Clock 200 MHz Technology DDR2 SDRAM Memory CAS Latency 6 What are the affect of the following Memory Type(given as 8 x 128 MB) Memory Clock (given in MHz) CAS Latency (given as 4,5,6) my Requirement is 2 GB DDR2 Type Desktop Please help

  Read the article

• SSH Tunnel for Remote Desktop via Intermediary Server

  - by Mihai Todor

  I've seen many examples of SSH tunnels on the nets, but I'm still having no luck with this. Here's the setup: Windows 7 PC in a private network, sitting behind a firewall, with PowerShellInsider SSH server set up and working fine. Public access Linux server, which has access to the PC. Windows 7 laptop, at home, from which I wish to do remote desktop on the PC. Now, here's what I've tried so far: SSH tunnel from my laptop to the Linux server: ssh -f my_user@LINUX_SERVER -L 6666:LINUX_SERVER_IP:6666 -N SSH to the Linux server where I've set up a tunnel to the PC: ssh -f 'PRIVATE_DOMAIN\my_user'@PC_NAME -L 6666:PC_IP:3389 -N Unfortunately, I must be doing something wrong, because it doesn't seem to work. Any ideas why or, at least, any suggestions on how can I try to debug this setup? At the moment, I have access to all 3 machines (non-root on Linux), so I can test whatever I want...

  Read the article

• Why does DBAN crash on my HDDs?

  - by John Watson

  I am using DBAN to erase HDD. DBAN is loaded from a CD and BIOS Boot order has been set to favour CD drive. On starting laptop, system boots from CD and DBAN interface can be seen. DBAN detects two storage devices, HDD and the SD Card. My HDD IS 320GB but DBAN says 298GB. It erases the SD card but when i try to erase HDD, it gives following error. DBAN finished with non-fatal errors. *ERROR /dev/sdb (process crash) *ERROR /dev/sda (process crash)

  Read the article

• Wamp website stop responding till restarting services [on hold]

  - by sparoww

  My first message here after many non conclusive research about my problem. So I'm administering a drupal website and I have migrate all application to new version: PHP 5.3.5 - 5.4.16 Apache 2.2.17 - 2.4.4 MySQL 5.1.36 - 5.6.12 With the new Wamp version. Also update Drupal from 6.19 to 6.30. I have update it by uninstalling everything in the server and reinstalling the new version. Since this update the website sometimes become unresponsive till we restart wamp. No warrning and no error in event log. Can somebody help me with this problem? I also cannot enable SSL, after configuring it wamp won't start. I have do many research and test but I still have many issue. Here I paste my configuration files: httpdconf: http://pastebin.com/qq1YvPKe httpdsslconf: http://pastebin.com/c4JnFyMw phpini: pastebinDOTcom/y8a30id6 Thanks in advance.

  Read the article

• Hyper-V Server hvremote.wsf Script - ns lookup for DNS Verification test fails

  - by Vazgen

  I'm trying to connect my Hyper-V Server to a Windows 8 client for remote management. I have: Joined server to WORKGROUP Enabled Remote Management Set the server name Set a static IP Set the DNS servers to my ISPs DNS Servers (same as default DNS Servers on my Windows 8 remote management client) Set the correct time zone Created net user on server (net user /add admin password) Added user to special Administrators group on server (hvremote /add:admin) Granted anonymous dcom access on client using hvremote However, the "ns lookup for DNS verification" fails on both the client and server with the same error: Server: my.isps.server.name.net Address: 111.222.333.1 *** my.isps.server.name.net can't find 192.168.1.3: Non-existent domain Thanks for the help.

  Read the article

• If I re-key a SSL certificate for a 2nd/backup server, does the original still work?

  - by Matt

  We have a production server with a wildcard SSL certificate. I'm in the process of creating a backup/failover server that will host the same domains, and therefore will also need the SSL certificate. The certificate on the primary server was installed with the private key non-exportable, so I am unable to export the certificate for installation on the failover server. My question then is - if I re-key the certificate from Go Daddy, does the original certificate installed on the primary server cease to be valid? As an aside, the original (primary) server is IIS 6, the failover is IIS 7 (once the failover is operational, we'll likely upgrade the primary).

  Read the article

• postfix/postdrop Issue with Solaris 10 (sparc) - permissions

  - by Zayne

  I am trying to get postfix (installed from blastwave) working on a Solaris 10 server, but only root is allowed to send mail. The problem appears to be permission related with postdrop. postdrop: warning: mail_queue_enter: create file maildrop/905318.27416: Permission denied I've checked that /var/opt/csw/spool/postfix/maildrop and /var/opt/csw/spool/postfix/public are both in the 'postdrop' group. main.cf contains setgid_group = postdrop. ppriv on postdrop as non-root user reports: postdrop[27336]: missing privilege "file_dac_write" (euid = 103, syscall = 5) needed at ufs_iaccess+0x110 I'm at a loss as to what to do next. I'm don't have much experience with Solaris; I use Linux daily. Any suggestions?

  Read the article

• PostgreSQL under Mac OSX Lion. Wrong userpass?

  - by Matt

  I'm completely helpless, maybe you guys can help me out. I installed PostgreSQL under my new MacOSX Lion. When I try to connect to my localhost with pgAdminIII.app it says: Error connecting to the database: FATAL password authentication failed for user postgres I just have no idea what to do? Non of my passwords work. Neither my adminpass nor "postgres" nor anyhting else. I tried to install it again via the console where I found this helpful link: http://www.peerassembly.com/2011/08/...resql-on-lion/ However the problem is, that when I try to run createuser -a -d _postgres the same password problem appears again. I just can't seem to find a solution to this. Always wrong password. Btw. I have a new User called "PostgreSQL" on my machine after I installed postgres. Any ideas? I'm so stuck and I really need to make this work.

  Read the article

• Remote desktop connection issues in windows server 2003

  - by rboorgapally

  Hi all, We are running windows server 2003 at our work place. I have enabled the remote desktop connections. I have also added all the users who connect to the server(three to four people) to the RDC group of users. Many of these users are also having Administrator access. The problem we are facing is that the connection is suddenly lost when we are working on something. Also, at times the system restarts by itself. Is this issue related to the limit on the number of users able to connect to the system? If so, why does the system accept new connections and/or terminate the existing connections? Has this anything to do with the users having administrator access so that all have equal prority and that is why existing connections are stalled? Also, please differentiate between console remote desktop and non console remote desktop.

  Read the article

• SAP PI 7.1 Runtime Workbench error: Domain ??? (domain.null)

  - by Techboy

  Within the Runtime Workbench screen of my SAP PI 7.1 system I have the error: Domain ??? (domain.null) Integration Server Integration Engines Non-Central Adapter Engines J2SE Adapter Tools The SLD CIM instance, class XI Domain shows: CreationClassName: SAP_XIDomain Name: domain.null Caption: Domain null With the associations: XI Contained Integration Repository XI Contained Integration Server XI Contained Integration Server If I do this: Move these associations to the correct SAP_XIDomain Delete the SAP_XIDomain 'Domain null' Restart the SLD Restart the SAP PI system it all appears okay (i.e. the 'Domain null') issue does not appear. The 'Domain null' issue re-appears as soon as I go into the SAP Runtime Workbench. Please can you tell me why it says domain.null and how to resolve it?

  Read the article

• Mod_rewrite pretty url when domain/foo is a directory

  - by ModRewriter

  Starting with something as simple as: RewriteRule ^(.*)$ index.php?page=$1 What if I also want the following to work: RewriteRule ^/foo$ /index.php?page=foo #/foo IS a directory This seem to work ONLY if the R flag is set, but then the full non-pretty url is written. Thus it seems I can REDIRECT existing directory, but not rewrite them... Maybe with an .htaccess inside the directory itself? Or some PHP magic in /foo/index.php like header(/index.php?page=foo)? Will it work? Will it be HTTP standard/search engine optimized? Please help! PS: The oddest idea occurred to me: redirecting /foo to /not-a-dir, and then rewriting /not-a-dir to /index.php?p=foo should theorically work... But... Come on... Really?!?

  Read the article

• Switches with 802.1x "supplicant timeout" feature?

  - by chris

  I'm looking for a complete list of switches which will allow 802.1x and normal (non-supplicant) enabled hosts to connect to the same ports on a switch. This is useful for areas where there are semi-open ports such as a lobby area or a library where corporate and guest users may use the same ports but you want them to have different access profiles and where it isn't expected that guests would have 802.1x configured on their system. For instance, Enterasys and Extreme Networks both have a feature where if the switch doesn't see an EAPOL packet from the client in a certain amount of time, it puts the port into a "guest" VLAN; if it sees an 802.1x supplicant, it tries to authenticate the user via 802.1x and if they succeed, it does what the radius server tells it to do with that port (IE put the port into a certain VLAN, apply certain ACLs, etc) Do other vendors have this sort of feature, or is it expected that a switch will do both 802.1x and MAC authentication, and the "supplicant timeout" feature is implemented with a blanket allow on the MAC authentication?

  Read the article

• How can I fix this configure error?

  - by balor123

  I'm trying to build mosh from source on a SUSE10 machine and am getting the following error: checking for protobuf... no configure: error: Package requirements (protobuf) were not met: No package 'protobuf' found Consider adjusting the PKG_CONFIG_PATH environment variable if you installed software in a non-standard prefix. Alternatively, you may set the environment variables protobuf_CFLAGS and protobuf_LIBS to avoid the need to call pkg-config. See the pkg-config man page for more details. I downloaded the source to protobuf and installed it in a custom path as well. I'm not using a package manager for any of this and cannot for various reasons outside the scope of the question. I added that custom path to my PATH and rehashed. Typically, this is enough for configure but in this case its not doing the trick. I added the prefix for protobuf to PKG_CONFIG_PATH but am still hitting this error. What should I do next to get past this error?

  Read the article

• How to get Atheros ar242x wireless adapter working under Debian Linux?

  - by Mark

  Does anybody know how to get the Atheros ar242x wireless adapter working under Debian Linux (5.0.2 and/or 5.0.3)? My Debian live CDs and install CDs both don't like this card at all. Curisouly, it seems to work on other, Debian-based, Linuxes. Is this a free/non-free Driver issue? I know Debian gets mardy about that. Although for what it's worth, the Live CD doesn't seem to detect my wired LAN connection either... Specifically this is on a Samsung R610 laptop (some version of which seem to have an intel wireless adapter - this one definitely doesn't!) I've tried all sorts of things but obviously on a live CD installing software is limited. I've also tinkerering with network config files and kernel modules etc but to no avail.

  Read the article

• How to plot survey results on Excel?

  - by Mulone

  Hi all, I would like to plot the average of these data sample: 1. Contribution to the project 2. Affiliation with project owners 3. Level of expertise 4. Learning Curve Yes No 3 2 No No 3 2 No No 4 3 No No 5 3 No No 3 3 Yes Yes 5 4 No No 4 3 No No 3 2 No Yes 2 4 No No 5 2 No Yes 5 No answer No No 2 2 No No 3 3 ... Basically I know how to do the average of each numeric column, but I have a few questions for you: If the column contains non numeric values (e.g. "no answer") the average doesn't work. Is there a workaround for this? How can I count the yes/no results and plot only a percentage? Thanks for any hints! Mulone

  Read the article

• Generate or update a PDF to include an encrypted, hidden watermark?

  - by Dave Jarvis

  Background Using LaTeX to write a book. When a user purchases the book, the PDF will be generated automatically. Problem The PDF should have a watermark that includes the person's name and contact information. Question What software meets the following criteria: Applies encrypted, invisible watermarks to a PDF Open Source Platform independent (Linux, Windows) Fast (marks a 200 page PDF in under 1 second) Batch processing (exclusively command-line driven) Collusion-attack resistant Non-fragile (e.g., PDF - EPS - PDF still contains the watermark) Well documented (shows example usages) Ideas & Resources Some thoughts and findings: Natural language processing (NLP) watermarks. Apply steganography on a randomly selected image. http://openstego.sourceforge.net/cmdline.html The problem with NLP is that grammatical errors can be introduced. The problem with steganography is that the images are sourced from an image cache, and so recreating that cache with watermarked images will impart a delay when generating the PDF (I could just delete one image from the cache, but that's not an elegant solution). Thank you!

  Read the article

• Isolate user from the rest of the system..?

  - by Shiki

  There is a non-techsavvy user, who doesn't want to learn, and can only use Windows XP or 7. The problem is, that the computer is shared which she would like to use, and the computer stores sensitive, important data. Since she clicks on everything, it's quite a russian roulette. How could I isolate her account from the rest of the system? Like having a profile on the computer (it runs Windows 7 now) which would have the files and other stuff sandboxed? I was thinking of having a dual boot system, but that could compromise the files too, or the boot sector (talking about Windows). Linux is not a way, hence ... see the first line. Is there such a software that can set up a sandboxed environment?

  Read the article

• Prevent registry changes by users

  - by graf_ignotiev

  Background: I run a small computer lab of 10 computers using Windows 7 x64 Enterprise. Our users are set up as limited users. For additional restrictions, I set up local group policy for non-administrators using the microsoft management console. Problem: Recently, I found out that some of these restrictions had been removed. Reviewing the settings MMC and in ntuser.pol showed that the settings should still be in place. However, the related registry settings were missing in ntuser.dat. I already have registry editing disabled in the GPO (though not in silent mode). Question: What is the best way to deal with this situation? Should I look into preventing registry setting changes? Should I set up registry auditing to found out how these keys are getting changed in the first place? Or should I give up the ghost and write some kind of logon script that enforces registry values if they've been change? Any other ideas?

  Read the article

• UFW: force traffic thru OpenVPN tunnel / do not leak any traffic

  - by hotzen

  I have VPN access using OpenVPN and try to create a safe machine that does not leak traffic over non-VPN interfaces. Using the firewall UFW I try to achieve the following: Allow Access from LAN to the machine's web-interface Otherwise only allow Traffic on tun0 (OpenVPN-Tunnel interface when established) Reject (or forward?) any traffic over other interfaces Currently I am using the following rules (sudo ufw status): To Action From -- ------ ---- 192.168.42.11 9999/tcp ALLOW Anywhere # allow web-interface Anywhere on tun0 ALLOW Anywhere # out only thru tun0 Anywhere ALLOW OUT Anywhere on tun0 # in only thru tun0 My problem is that the machine is initially not able to establish the OpenVPN-connection since only tun0 is allowed, which is not yet established (chicken-egg-problem) How do I allow creating the OpenVPN connection and from this point onward force every single packet to go thru the VPN-tunnel?

  Read the article

• Windows Vista taskbar not resizing desktop

  - by Luke Schafer

  Hi, I recently started having a frustrating problem with Vista on my laptop that I can't seem to solve. I'm trying to get it to have the vanilla taskbar settings - always shown, resizes the desktop area (as in, the space the taskbar takes up isn't available for fullscreen windows), and always on top. No matter what combination of settings and toggles I do, I can't get it. With the normal settings that achieve this (Only keep on top, and optionally locked, checked), I get: Desktop extends behind the taskbar (so icons and the like are behind it) Non-maximised windows appear behind it when overlapping. Maximised windows take the full area of the screen and are behind the taskbar Maximised Google Chrome takes the full screen size and is in front of the taskbar I tried googling and also just randomly toggling on and off the settings, haven't found a fix.

  Read the article

• System Monitoring Redundancy

  - by Josh Brower

  I consult in a small business environment where I have two HyperV hosts (with <10 VMs) + a couple other servers. I recently had an issue where one of the HyperV hosts had a CPU issue and it came down, bringing most of my non-critical VMs with it, plus a free piece of software that I use for network & system monitoring and availability. Because of this, and the fact that iDRAC locked up to, I did not get any alerts about the crash. So I am wondering how I can (cheaply) get a redundant availability monitoring system in place--Is is as simple as running Nagios or Zenoss (or whatever) on two different HyperV hosts? It just seems like running more than one copy of Nagios/Zenoss/etc could be expensive and have high overhead. Thoughts? Thanks! -Josh

  Read the article

• reverse nslookup fails for single machine

  - by matt wilkie

  I have a computer on a windows Active Directory network for which reverse dns lookup fails. It doesn't matter which machine runs the lookup. The problem computer is a debian vm on a windows server 2003 host. >nslookup wiki.dept Server: primary.internal.domain.org Address: 192.111.222.44 Name: wiki.dept.internal.domain.org Address: 192.111.111.185 >nslookup 192.111.111.185 Server: primary.internal.domain.org Address: 192.111.222.44 *** primary.internal.domain.org can't find 192.111.111.185: Non-existent domain Contents of /etc/resolv.conf on the debian guest: nameserver 192.111.111.244 nameserver 192.111.222.44 search internal.domain.org What is wrong? how do I get ip-to-name resolution to work for this machine? Thank you.

  Read the article

• VSFTPD uploaded file permissions

  - by Katafalkas

  Let me first say that there are loads of topics regarding this, and I am sure i have seen them all by now. Still non of the solutions seem to help. I installed vsftpd. created a user ftp-data. Now I need that files uploaded by user ftp-data would have 755 permissions. Solving this should be as easy as adding: local_umask=002 file_open_mode=0755 but that did not help, then I have tried a number of variations of this, still did not help. The I added: chmod_enable=YES still did not help. At the moment I think that I am missing something very simple and obvious, just cant find it. Maybe someone could help me to find what I am missing. This is my config file: anonymous_enable=NO local_enable=YES write_enable=YES local_umask=002 anon_upload_enable=NO anon_mkdir_write_enable=NO dirmessage_enable=NO xferlog_enable=YES connect_from_port_20=YES xferlog_file=/var/log/xferlog listen=YES local_root=/var/www/ftp-gallery pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES

  Read the article

• How to use a custom Windows 7 system drive letter?

  - by Ivan

  The subject PC has many hard drive partitions dedicated for different purposes, C: being a Windows XP system drive and F: (which is actually the next primary partition placed right after C: physically) being intended to host a newly installed Windows 7 instance (meant for "dual boot" configuration). Needless to say the intention was all the partitions to have exactly the same letters under both OSes, needless to say Windows 7 has detected all of them in a completely different order which would not be a problem (as the non-system drives letters can be changed easily after installation) if it wouldn't have named it's system drive C: (meant to be F:), which I have no Idea how to change. Is there a way to set the letter you want? I don't mind reinstalling Windows 7 from scratch if it is to be set at installation time or even configured in some text files on the installation DVD. I have tried this way, but it renders the Windows 7 system desktop unbootable (gets stuck on "Preparing your desktop..." after "Welcome").

  Read the article

< Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >