Search Results

Search found 26693 results on 1068 pages for 'back to basics'.

Page 234/1068 | < Previous Page | 230 231 232 233 234 235 236 237 238 239 240 241  | Next Page >

  • Intel ICH9/10R raid 5 drive failure

    - by davpen
    About a year ago I was using the native Intel ICH9R Raid 5 an Intel P35 based motherboard. The system was running Vista x64 and when one of the drives failed Vista blue screened on boot until I had figured out which drive had failed and removed it (a rather nerve racking hit and miss affair). The same thing happened some months later on another similar system so it wasn't a once off. This wasn't the robust raid 5 drive failure behavior that I would have hoped for and expected. I moved to Highpoint Rocketraid 2300 and haven't had any problems although I have yet to have a drive fail with this set up. But I am now looking to build a new system based on an i7 and Windows 7. At the moment Highpoint doesn't have drivers for Windows 7 so I am considering moving back to the on board Intel Raid. Yes I know I that I might get away with using the Vista drivers but I don't really want to take that chance with critical data. The question then is has anyone else experienced a drive failure with Intel raid and how did the OS and drivers handle it? Is it safe to go back?

    Read the article

  • Western Digital My Book not recognized by WD software

    - by Kari
    A few years ago I bought a WD My Book Pro 2. It worked fine for a while, then one of the drives failed and I sent it back to be replaced under warranty. I never got around to setting up the new one when I got it back. I finally ran out of room on my internal drive, so I tried to use the external - no go. Both drives spin up, but aren't recognized by either Disk Utility (Mac) or the WD Drive Manager. I tried on a PC as well with fresh software. Then I pulled the drives out of the enclosure (warranty is already expired) and plugged them straight into the PC. Both recognized and working 100% in RAID0. BIOS recognizes either disk as functional; Windows only sees them when both are connected due to the RAID which I can't change without the WD software. The drives that were returned to me are the "Green" drives which I've read are NOT recommended for RAID. Is it possible that this is interfering with them reading externally? Any other ideas? My main computer is a laptop so using them internally isn't an option :(

    Read the article

  • Microsoft Mouse and Keyboard Center Needed for Keyboard but Doesn't Support Mouse

    - by eljay
    I recently built a new computer (running Win7 Pro 64-bit) that includes the Microsoft Sidewinder X4 Keyboard. To make use of all the extra features of this keyboard I need the Mouse and Keyboard Center. I just ran Windows Update for the first time on this system and the Mouse and Keyboard Center was included in the update. I'm left-handed and before the update I had the mouse set up for lefty use. Now after the update, it's been set to righty use and the original mouse control panel applet no longer allows the assignment of buttons. For that there's a link to the Mouse and Keyboard Center which does not support my oldish mice. (I have an IntelliMouse Optical and a Creative Mouse Lite Pro.) So I need the new utility for my keyboard, but I have to be right-handed to use my mouse? Really! I tried changing HKCU\Control Panel\Mouse\SwapMouseButtons to 1, but a reboot set it back to 0. Is there some way I can change my mouse back to left-handed? Thanx -eljay

    Read the article

  • How do I keep a bridge enabled on a bonded interface?

    - by jlawer
    I'm working on setting up a pair of CentOS 6.3 servers that will run a couple of KVM vms and have come across a problem setting up a bridge on a bond. I am using Mode 4 (802.3ad) bonding on a pair of stacked Dell Powerconnect 5524 switches connecting to R320 servers. There are 2 links (1 to each switch) that form a Link Aggregation Group (802.3ad / LACP bonding). On top of the bond I have VLAN Tagging. I've verified this is a problem on multiple other bonding modes so it isn't just a mode 4 issue. I am testing what happens when 1 link is dropped (ie switch dies, cable breaks, etc). If I don't have a bridge (for KVM), everything works fine, failover happens as expected. If I have the bridge enabled, it works fine until failover (unplugging a cable). When failover happens /var/log/messages shows the slave link going down, followed within a second by: kernel: br1: port 1(bond0.8) entering disabled state The thing is /proc/net/bonding/bond0 shows the link is up as expected (simply with only 1 slave instead of 2). If I plug the cable back in it recovers and brings the bridge back to an enabled state. I actually have tested this while a ping is occuring and if the timing is right a packet will actually leave the system after the link is lost, but before the disabled message occurs. This disabled state I assumed was STP, but I have disabled STP on the bridge configuration and this issue still occurs. brctl showstp br1 still shows the link as disabled when it is running without a slave. I also switched between the nics in the server (I have 2x Broadcom & 4x intel). It doesn't matter which configuration I have. Does anyone know of a way to force the bridge to stay enabled or why its detecting the bond as disabled, when it isn't?

    Read the article

  • Replacing compiz/metacity with openbox reduces workspaces to 1

    - by Brian
    I like to use the GNOME desktop, but I prefer to replace its window manager with openbox, with 4 workspaces. However, when I run openbox --replace, the number of workspaces available drops to 1. If I go into obconf, workspaces is still configured to be 4 (~/.config/openbox/rc.xml shows the same). I can get the workspaces to reappear by changing the value in obconf to anything else, and then back to 4. I have just been dealing with this problem since Ubuntu 9.04 (now up to 10.10) since I don't reboot very often. But it's really annoying to have to reset my workspaces whenever I do have to reboot. Changing the value in rc.xml and running openbox --reconfigure does not seem to have any effect. So what is obconf doing that I'm not (sends a dbus message perhaps [EDIT: watching with dbus-monitor I see no messages when changing the workspaces value in obconf])? I was hoping there would be a cleaner way to change the window manager than just running openbox --replace at login. So my questions are: Is there a better way to specify an alternate window manager (i.e. a way that doesn't cause the workspaces to break)? If not, how can I automatically set the number of workspaces back to 4? Update: I finally got around to trying what I commented on MrShunz's answer (adding WINDOW_MANAGER=/usr/bin/openbox to ~/.gnomerc). But the effect is the same as openbox --replace.

    Read the article

  • My PC is powercycling, what's going wrong?

    - by Renai
    So here is my sorry story of woe. My PC has been functioning normally for some time. Last week I bought a cheapish powered USB hub and plugged it into my home PC, which runs Windows 7. This weekend I plugged that hub into my home PC. At some stage I hibernated the PC. Then later on I plugged my Kobo eReader into the hub to charge. Later on I started the PC up. Only thing is, it now won’t start up. It just powercycles on for a second and a half with the fans at full, then powercycles off. Then back on for two seconds, then back off. There’s no display at all and it won’t get to the BIOS screen. It looks like anything USB is not functioning — the keyboard and mouse are not lighting up etc. I’ve taken out the BIOS battery and reseated the RAM, reseated the graphics card and so on, but my suspicion is that I have blown the USB section of the motherboard somehow. Suggestions? All else failing, where is the best place to take this machine in Sydney to get evaluated? It’s a fairly powerful beast, all up has cost me about $2500 over the years, including upgrades and a recent new graphics card, so can’t just start from scratch.

    Read the article

  • New SSD, is the MBR broken? DISK BOOT FAILURE

    - by Shevek
    I've been running Windows 7 on a WD 500gb SATA single drive, single partition setup for some time with no issues. I've just installed a new Kingston V Series 64gb SSD and performed a clean install of Win7 to it, deleting the partitions on the 500gb and using that as a data drive. All was well for a few reboots but then I started to get "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER" messages. If I put the Win7 install DVD back in the drive it boots fine. Tried a clean install again, after replacing SATA cables and swapping SATA ports, with a complete partition wipe of both drives. Again, rebooted fine a few times then back with the "DISK BOOT FAILURE" error. Looked on the web and found some discussions about it so I then started from scratch again. This time I wiped the MBR on both drives using MBRWork, disconnected the 500gb and reinstalled to the SSD. Removed the install DVD and installed all the drivers which involved many reboots, all with no problem. To make sure I also did a few cold boots as well. Reconnected the 500gb, initialised, partitioned and formatted it. Copied data to it and did some more reboots and shutdowns. All was ok. Then out of the blue comes another "DISK BOOT FAILURE" and again, if the Win7 install DVD is in the drive it boots fine. So, is the SSD a bad'un? TIA UPDATE: It was a BIOS issue! I found a hidden away option for HDD boot order, which was separate from the usual HDD/CDRom/FDD boot order option. The WD was set to boot before the SSD... Swapped them round and all is well. Still don't understand how it worked at first though... Thanks Solaris

    Read the article

  • MySQL select query result set changes based on column order

    - by user197191
    I have a drupal 7 site using the Views module to back-end site content search results. The same query with the same dataset returns different results from MySQL 5.5.28 to MySQL 5.6.14. The results from 5.5.28 are the correct, expected results. The results from 5.6.14 are not. If, however, I simply move a column in the select statement, the query returns the correct results. Here is the code-generated query in question (modified for readability). I apologize for the length; I couldn't find a way to reproduce it without the whole query: SELECT DISTINCT node_node_revision.nid AS node_node_revision_nid, node_revision.title AS node_revision_title, node_field_revision_field_position_institution_ref.nid AS node_field_revision_field_position_institution_ref_nid, node_revision.vid AS vid, node_revision.nid AS node_revision_nid, node_node_revision.title AS node_node_revision_title, SUM(search_index.score * search_total.count) AS score, 'node' AS field_data_field_system_inst_name_node_entity_type, 'node' AS field_revision_field_position_college_division_node_entity_t, 'node' AS field_revision_field_position_department_node_entity_type, 'node' AS field_revision_field_search_lvl_degree_lvls_node_entity_type, 'node' AS field_revision_field_position_app_deadline_node_entity_type, 'node' AS field_revision_field_position_start_date_node_entity_type, 'node' AS field_revision_body_node_entity_type FROM node_revision node_revision LEFT JOIN node node_node_revision ON node_revision.nid = node_node_revision.nid LEFT JOIN field_revision_field_position_institution_ref field_revision_field_position_institution_ref ON node_revision.vid = field_revision_field_position_institution_ref.revision_id AND (field_revision_field_position_institution_ref.entity_type = 'node' AND field_revision_field_position_institution_ref.deleted = '0') LEFT JOIN node node_field_revision_field_position_institution_ref ON field_revision_field_position_institution_ref.field_position_institution_ref_target_id = node_field_revision_field_position_institution_ref.nid LEFT JOIN field_revision_field_position_cip_code field_revision_field_position_cip_code ON node_revision.vid = field_revision_field_position_cip_code.revision_id AND (field_revision_field_position_cip_code.entity_type = 'node' AND field_revision_field_position_cip_code.deleted = '0') LEFT JOIN node node_field_revision_field_position_cip_code ON field_revision_field_position_cip_code.field_position_cip_code_target_id = node_field_revision_field_position_cip_code.nid LEFT JOIN node node_node_revision_1 ON node_revision.nid = node_node_revision_1.nid LEFT JOIN field_revision_field_position_vacancy_status field_revision_field_position_vacancy_status ON node_revision.vid = field_revision_field_position_vacancy_status.revision_id AND (field_revision_field_position_vacancy_status.entity_type = 'node' AND field_revision_field_position_vacancy_status.deleted = '0') LEFT JOIN search_index search_index ON node_revision.nid = search_index.sid LEFT JOIN search_total search_total ON search_index.word = search_total.word WHERE ( ( (node_node_revision.status = '1') AND (node_node_revision.type IN ('position')) AND (field_revision_field_position_vacancy_status.field_position_vacancy_status_target_id IN ('38')) AND( (search_index.type = 'node') AND( (search_index.word = 'accountant') ) ) AND ( (node_revision.vid=node_node_revision.vid AND node_node_revision.status=1) ) ) ) GROUP BY search_index.sid, vid, score, field_data_field_system_inst_name_node_entity_type, field_revision_field_position_college_division_node_entity_t, field_revision_field_position_department_node_entity_type, field_revision_field_search_lvl_degree_lvls_node_entity_type, field_revision_field_position_app_deadline_node_entity_type, field_revision_field_position_start_date_node_entity_type, field_revision_body_node_entity_type HAVING ( ( (COUNT(*) >= '1') ) ) ORDER BY node_node_revision_title ASC LIMIT 20 OFFSET 0; Again, this query returns different sets of results from MySQL 5.5.28 (correct) to 5.6.14 (incorrect). If I move the column named "score" (the SUM() column) to the end of the column list, the query returns the correct set of results in both versions of MySQL. My question is: Is this expected behavior (and why), or is this a bug? I'm on the verge of reverting my entire environment back to 5.5 because of this.

    Read the article

  • Some process/service/driver repeatedly presses F5

    - by VitalyB
    Hi everyone, I have the strangest problem that started 2 days ago (Windows7, 64bit). SOMETHING causes my F5 key to be constantly pressed. Rebooting helps, but only for a while, it keeps coming back to that. So far I've tried to disconnect and reconnect the keyboard (physically), however, disconnecting the keyboard doesn't actually do anything. Reconnecting it back again, causes the F5-pressing to stop, but not for very long (seconds/minutes). I'd really like to avoid a binary search for the programs (process closing/keyboard switching/etc) before I can, at the very least, identify the source of the keypress. Is there an application that can show me what is causing a key press? E.g is it the keyboard driver, or some process that executes SendKey repeatedly for reasons unknown. Thanks! P.S FYI, having F5 causes the strangest side effects. Task Manager refreshes very very quickly (as F5 is refresh), the desktop is constantly flickering and all the browsers stop working as they keep trying to refresh. I was lucky to find out what the heck is happening only because I started notepad and saw that current date/time started to appear constantly. If not that, I'd still be wondering.

    Read the article

  • How to re-add a RAID-10 failed drive on Ubuntu?

    - by thiesdiggity
    I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

    Read the article

  • Issues using gmail with google apps and external domain

    - by Jonathan Kelly
    I have recently tried to use gmail through google apps as my main email client, but I'm experiencing a few different problems. I am managing the domain (conjunktiondesign.co.uk) through 123reg.co.uk but it is hosted through fasthosts.co.uk. I transfered the domain to 123reg as fasthosts did not allow me to change the MX records myself. I followed the setup instructions step by step on google apps and changed the MX records as they told me to. My email was now working perfectly but my website was down and I was getting the following error: The dnsserver returned: No DNS records I have a friend that is using the same system as me (ie. Externally hosted domain and google apps mail) and I changed my 123reg details to the same that he had (as his was working perfectly - both email and website). I changed my name servers to point to fasthosts, rather than 123reg and I added an A record called '@' pointing to fasthosts IP address. I also created another A record called 'www' pointing to fasthosts IP address. After I did this, my website worked almost immediately but I have only realised that since changing it my email is now down. I have not received anything since Saturday. I am a web designer and would consider myself fairly tech savvy, but I have no idea about A records, CNAME's and all the things I have been messing about with! What I ultimately need is someone to help me get my email and website working at the same time, rather than one being down when the other is OK. I seem only able to get one or the other working. I have now changed the name servers back to 123reg in an attempt to get my email back as it is more important than my website at this stage. Any help is much appreciated. Thanks.

    Read the article

  • VLAN Tagging Traffic on Cisco Switch

    - by David W
    I have a situation where I'm setting up multiple VLANS on a pfSense firewall on the same physical interface for a client. So in pfSense, I now have VLAN 100 (employees) and VLAN 200 (students - student computer lab). Downstream from pfSense, I have a Cisco SG200 switch, and coming off of the SG200 is the student lab (running on a Catalyst 2950. Yes, that's old, but it works, and this is a poor nonprofit we're talking about). What I'd like to do is tag everything on the network as VLAN 100, except for the student computer lab. Earlier today when I was on-site with the client, I went into to the old Catalyst 2950, and assigned all of its ports to access VLAN 200 (switchport mode access vlan 200) without setting up a trunk on the Catalyst or on the SG200. Looking back on it, I now understand why internet in the lab broke. I reverted the lab back to the default VLAN1 (we're still running on a different firewall - we haven't deployed pfSense -, and the traffic is still separated physically). So my question is, what do I need to do in order to properly deploy this scenario? I believe the correct answer is: Ensure VLANs 100 and 200 are setup in pfSense, and that DHCP is operating correctly (on separate subnets) Setup a trunkport VLAN that allows both 100 & 200 traffic, and plug that port directly into pfSense. Setup a VLAN 200 trunkport on the SG200 (It's not running iOS, but if it were, the command would be switchport trunk native vlan 200), which will then plug into the Catalyst 2950. Setup a VLAN 200 trunkport on the Catalyst 2950 (that is plugged into the SG200 VLAN200 port with the same command - switchport trunk native vlan 200) Setup the rest of the ports on the old Catalyst 2950 in the lab to be access ports on VLAN200. Is there anything that I'm missing, or do I need to tweak any of these steps, in order to properly segment the network traffic?

    Read the article

  • SSH attack CentOS Amazon EC2

    - by user37143
    Hi, I run a few Rightscale CentOS AMI based instances on Amazon EC2. Two months back I found that our SSHD security is compromised( I had added host.allow and host.deny for ssh). So I created new instances and done an IP based ssh that allows only our IPs through AWS Firewall(ec2-authorize) and chnaged the ssh 22 default port to some other port but two days back I found I was not able to login to the server and when I tried on 22 port the ssh got connected and I found that sshd_conf was changed and when I tried to edit sshd_config I found root had no write permission on the file. So I tried a chmod and it said access denied for 'root' user. This is very strange. I checked secure log and history and found nothing informative. I have PHP, Ruby On Rails, Java, Wordpress apps running on these server. This time I did a chkrootkit scan and found nothing. I renamed the /etc/ssh folder and reinstalled openssh through yum. I had faced this on 3 instances on CentOS(5.2, 5.4) I have instances on Debian as well those working fine. Is this a CentOS/Rightscale issue. Guys, what security measures I should take to prevent this. Please support me this is very critical. Thanks

    Read the article

  • Access denied to external USB disk; update access rights fails in Windows 8

    - by gerard
    I use to work with 2 laptops (Windows vista and Windows 7), my work files being on an external usb disk. My oldest laptop broke down, so I bought a new one. I had no option other than take Windows 8. I suspect something changed with access rights, as my external disk suffered some "access denied" problem on Windows. I was prompted (by Windows 8) somehow to fix the access rights, which I tried to do, getting to the properties - security. This process was very slow and ended up saying disk is not ready Additionally, my external usb disk somehow was not recognized anymore. Back to Windows 7, I was warned that my disk needed to be verified, which I did. In this process, some files were lost (most of them I could recover from the folder found00x, but I have some backup anyway). Also, I don't know why, but under Windows 7, all the folder showed with a lock. Then back again to Windows 8. Same problem : access denied to my disk + no way to change access rights as it gets stuck disk is not ready". Now I am pretty sure there is some kind of bug or inconsistency in Windows 8 / Windows 7. I did 2. and 3. a few times. At some point, I also got an access denied in Windows 7. I could restore access rights to the disk to "System" (properties - security - EDIT for full control to group "system". ). But then I still get the same access right pb on Windows 8, and getting stuck in the process to restore full control to "system" -- and "admin" groups. I upgraded Windows8 with the Windows8 updates available. Does not help.

    Read the article

  • Periodic internet connection drops

    - by sterlingholt
    My setup is a dsl modem, and a dlink di 524M router. I'm also using a Witopia VPN which runs through OpenVPN. I've been having trouble with the internet connection dropping very frequently. It comes back shortly, without even a router/modem/computer restart. This happens as frequently as every ten minutes. Occasionally (not often) it will last as long as an hour or two without dropping. When it drops, I can get it back almost immediately by clicking Reconnect in the OpenVPN GUI and letting that do it's thing. It's worth noting that I'm in China. Calling support is a bit difficult because of that. Also I don't really understand all of the router's software, although I've got it generally figured out. I've tried a bunch of stuff, attempts to diagnose and/or fix the problem. No success with any of the following: I've power cycled both the modem and the router. I've tried an ethernet connection to the router. I've connected without the VPN. I've disabled IEEE authentication on all connections. I've checked for viruses. I've tried lifting it off the ground so as to prevent overheating.

    Read the article

  • Keyboard doesn't function after Fedora 17 update

    - by mickburkejnr
    I updated my Fedora 16 installation to Fedora 17 on Saturday, and the update worked without reporting any errors. I carried on working on the machine in question and then switched the computer off. Last night I went back on the computer, I switched it on and got to the log in screen. At this point I tried to type in my password but the keyboard wouldn't work. I unplugged it (it's a PS/2 keyboard) and plugged it back in. The lights flashed for a split second but the keyboard still wouldn't work. I then plugged the keybaord in to a USB to PS/2 adapter, and the keyboard still wouldn't work. I restarted the computer and tried to access the BIOS and I was able to do so. So the keyboard doesn't seem to be faulty, it just doesn't work when Fedora boots in to the GUI interface. I did try to boot in to the "recovery mode" of Fedora, and the keyboard works here with no problem. As I still have access to Fedora via a terminal interface, is there anything I can do to fix the keyboard problem via the terminal without having to reinstall Fedora?

    Read the article

  • why does my computer crash?

    - by chobo2
    Hi my computer keeps crashing and I don't know why. At first I thought because I had my cpu over clocked that it all of sudden was crashing. So I set my cpu back to regular speed. This did not help. I then thought it was because 2 sticks of my memory where from a computer that suffered from a power surge. However I just ran the windows memory diagnostic tool( extended) and after like 6 hours of testing my memory it found no errors. So now the only thing that is left is windows 7 64bit. I first over clocked my cpu for a couple months while running XP. Never had a problem. I installed the memory and windows 7 at the same time. But I not sure if it is my memory now since it passed the diagnostic tests. However I am not sure if it is windows 7 either has I installed it twice in the last year. I really don't want to go back to XP to find out if this is the case. So here are my blue screens of deaths(from bluescreen). https://sites.google.com/site/myerrorswin7/errors (I hope you enjoy my great site lol) As you can see most of them are different NTFS_FILE_SYSTEM KMODE_EXCEPTION_NOT_HANDLED BAD_POOL_HEADER IRQL_NOT_LESS_OR_EQUAL SYSTEM_THREAD_EXCEPTION_NOT_HANDLED SYSTEM_SERVICE_EXCEPTION

    Read the article

  • Best Practices for adding Exchange Archive to current 3 server setup

    - by ADquestion
    I'm looking to add an Archive Database (which I know is just a Mailbox Database) to our current Exchange 2010 environment. I have done this in the past at a previous job, but we had a simpler setup than at this current job. I've been trying to find some best practices to make sure it's setup in an ideal way, but so far not finding the details I would prefer. Hoping someone on here can give me a few pointers. Currently we have a 3 server setup, Server1, Server2 and Server3. Three databases of course, DB1, DB2 and DB3. We have a DAG setup between them. Server1 has DB1 and DB3 on it, DB1 is not active, DB3 is active. Server2 has DB1 and DB2 on it, both are active. Server3 has DB2 and DB3 on it, both are not active. All three servers are virtual (VMware). Each one is setup identical to the other as follows: C:\ 60GB - OS E:\ 600GB - DB (currently only 90GB used, pointing to Datastore just for Server2) F:\ 200GB - Log (2GB used, pointing to same Datastore as above) G:\ 200GB - Restore (0 used, pointing to same Datastore as above) The drives are all set to Thin Provisioning, and it looks as though I have 600GB of available space. They have not been on Exchange that long and only have about 70GB worth of PSTs to import back in that will be going to the Archive Database, plus anything older than 2 years from their current inbox that will be moved into there. I was considering placing the Archive DB on the E:\ drive of Server3 (only) like the current DB, but wasn't sure if that was acceptable. I don't plan on setting the Archive DB up with the DAG, just plan on having it as a single repository for older emails and manually back it up every now and then. If anyone has any suggestions on this I would appreciate it the input. I've done it on a slightly smaller scale before and it worked well, but like to think it through before pulling the trigger, especially at a new job. :) Thanks again!

    Read the article

  • VPS to replace MobileMe or Google Apps.

    - by Alex
    All, Yes, this has been touched on in other questions, but I can't find something similar enough. I currently have Google Apps hosting personal email, calendars, contacts, etc. I do like the other google services, but they're outside of Apps. One of the little google irritations that I have to maintain a separate account for Picassa, etc. So, I'm thinking about moving myself away from Google, but purely for personal, privacy type issues. Do I really like the ads, the email snooping, etc? I've had, and liked MobileMe, back when it was iTools, and then .Mac, but it doesn't offer that much really. How easily can I replicate it all on a VPS? I don't want to host it myself at home, I'd lose all the wonderful datacenter goodness. THis isn't about personal geekery in my own basement, just about taking a little control back from Google. So, email is fine running an IMAP server, a nice front-end, etc. What about Calendars and Contacts? And, how easily can it be setup to sync to the desktop and iPhone? Thanks.

    Read the article

  • How to get rid of "Maxback Engine" for good?

    - by Jonik
    I used to have a Maxtor Shared Storage II network drive; it broke down long ago already. (Later I tried to recover some data from it, and partially succeeded, but haven't yet fully documented it on that question.) Anyway, I just noticed there are still some lingering bits remaining of the (thourougly crappy) software that came with the Maxtor device: a background process called "MaxBack Engine". I googled around a bit and found something related but not very useful: http://www.straitmac.com/jforum/posts/list/600.page http://discussions.apple.com/thread.jspa?threadID=725692 Under /Applications I found "Maxtor EasyManage.app" which I used to use for controlling the drive, and showed it some "rm -rf". Before deleting, I noted that the bundle did contain "MaxBack Engine.app" under Content/Resources. But still, after reboot, the "MaxBack Engine" process is back. I did notice though that it only appears when logging in with my usual user account; with another account it wasn't launched. So, dear Mac gurus, what could I do about this pest? I guess I could fall back to some Unix hackery and write a cronjob that kills any process with that name, but obviously it'd be nicer to be able to clean up from my computer everything left behind by Maxtor's piece of software.

    Read the article

  • How can I restore my laptop from Windows 7 to its original Windows Vista recovery partition?

    - by Cam Jackson
    I bought my Acer laptop 4 years ago with Vista Home Premium x86. It has a recovery partition that I have used successfully in the past to format everything and reinstall Windows to factory settings. I have since upgraded to Windows 7, but I now need to get back to my original installation. Not sure what it's called, but I can successfully get into this recovery thingy: However, when I click the third option (for me I think it says 'Windows Image Recovery' or something like that) it tells me that it can't find any images to recover from :( I have checked and I don't have a windows.old that I can recover from either. One final note, if I launch diskmgmt.msc, these are the partitions: Why is the first partition shaded? Does that mean anything? Both of the 'unlettered' partitions are 100% empty. Did the Windows 7 upgrade process format my Vista system recovery partition?! And finally: How can I get back to my factory settings? EDIT: I did see this question, but neither of the answers apply to my situation. Edit to address jdh's answer: From what I can tell, I never get the option to boot the Vista recovery partition. After hitting F10, I get this screen, except it's partition 2, and I don't have the IN/MINT bit: I hit Escape, and then I get this screen, except without Ubuntu listed, and without the auto-countdown thing: I hit F8, and then I get this screen: I hit Enter on the first option, I end up at the screen in the first screen shot. As I said, from there I click the third option, and it fails to find the image, which I guess makes sense if it's only looking for a Windows 7 recovery. So I either need to make the Windows 7 tool see the Vista recovery partition, or I need the boot loader (?) to let me select Vista earlier in the process. Any ideas?

    Read the article

  • Windows 8 keeps signing out

    - by bill weaver
    Ran into a strange problem with Windows 8 Pro. Last night i installed Windows 8 Pro as an upgrade on a Sony Vaio laptop that had Windows 7 Pro on it. The install seemed to go okay. Then once installed, live tiles seem to work, native/Metro apps will start okay, but pretty soon after going into an app or settings, the screen flashes a few times and we're back to the lock screen. Signing in appears to do a full login. I've tried this with a local account and with a live.com account. This is someone else's laptop, so we decided to let it breathe, in case the install was still settling in. Well, they say today it's doing the same thing. Open the music app, and within a minute it's back to signon/lock screen. However, they can go to the actual Desktop and run Zune to play music, and it seems happy. In the past, i've installed retail Windows 8 Pro clean on a homebrew system, as an upgrade on a Dell laptop with a zillion apps and drivers, neither with any problems. Also, i've had the consumer preview and release candidate installed as well, no problems. Any ideas on what's going on here?

    Read the article

  • Window 7 Computer name changing on its own?

    - by DC
    Very odd problem... I have a Dell Latitude D830 with XP Pro that has been running on my local domain for many years. I recently Installed Windows 7 Enterprise on the D830 using a brand new HDD so that I could still use XP if I needed by just swapping out the HDD's. I added the W7 installed system to my domain using a completely different machine name than that used for the XP system and everything seemed to be functioning as it should. On boot up over the last 2 weeks or so I occasionally (3 times now) get to the login screen and try to login to the domain only to get an error saying that the Computer name is not a trusted machine in the domain I'm trying to log in to. Come to find out that the machine name on the W7 system has been changed somehow to that of my old XP system. If on the W7 system I then change the name back to the correct name, disjoin the domain, reboot, add the machine back into the domain … all is well for an unknown period of time until this happens again. This last time, I know for a fact that everything was fine the day before when I shut down the system. I came in today, powered up the system and the machine name had been changed to that of my old XP system again. Has anybody else seen this behavior or hav any ideas on what could be causing it? Thanks!

    Read the article

  • Word 2010 creates multiple processes... sometimes

    - by Bill Sambrone
    I've run into a strange behavior when I migrated our users from Office 2007 / Vista to Office 2010 / Windows 7 (all 32-bit). They use a web based document management system called NetDocuments which stores all their .doc/.docx files. Generally, when they click on a doc from the browser window it fires up Word and opens the doc. Word has an add-in in it from NetDocs as well so it can upload the changed document directly back to the NetDocs server. I get a phone call when Word crashes, and every single time it has crashed I have witnessed multiple winword.exe processes running in task manager. I used process explorer to see what created the process, and it is all Internet Explorer. So far I have rolled them back to IE8 and the problem happens less frequently, but it still happens. When I try to duplicate the problem, I can make it happen sometimes if I open multiple documents very quickly. Using lightning fast alt-tab reflexes, I DO see that a 2nd WinWord process is created when a user clicks on a document, then it closes once the document is open. I think what is happening is that the secondary WinWord process that does some sort of NetDocs voodoo is getting stuck open. This behavior is new to Word 2010 / Windows 7 and google searching isn't coming up with much. I have seen a few posts that this is a known issue in certain circumstances and there is no "fix", but I thought it would good to ask others on this. Thanks!

    Read the article

  • Thecus N5200, disk has dropped out of RAID5

    - by Anders Ekdahl
    We have a Thecus 5200 NAS here at work with five WD Caviar Black 2TB disks in a RADI5 array. Yesterday, disk 4 dropped out of the array, and in the NAS web interface there's a warning about the RAID array being "degraded". When I go into Storage - Disks, disk 1 and 4 has a warning next to them. When I click on the warnings, this information about the disks are displayed: Tray Number 4 Model WD2001FASS-00W2B Power On Hours 2403 Hours Temperature Celsius 34 Reallocated Sector Count 66 Current Pending Sector 1447 Raw Read Error Rate 61 Seek Error Rate 0 Hardware ECC Recovered N/A Tray Number 1 Model WD2001FASS-00W2B Power On Hours 2403 Hours Temperature Celsius 32 Reallocated Sector Count 0 Current Pending Sector 1465 Raw Read Error Rate 0 Seek Error Rate 0 Hardware ECC Recovered N/A I'm not really an expert on either disks or RAID arrays. Does this indicate that the fourth disk is damaged, and needs to be replaced? And what about disk number one? It has a warning, but it's still in the array. Is it safe to add the fourth disk back into the array as a spare? I can't find any way to add it back as a it were before.

    Read the article

< Previous Page | 230 231 232 233 234 235 236 237 238 239 240 241  | Next Page >