Search Results

Search found 7546 results on 302 pages for 'mail forwarding'.

Page 235/302 | < Previous Page | 231 232 233 234 235 236 237 238 239 240 241 242  | Next Page >

• Reducing the size of the EDB file.

  - by Toby

  I have hit an issue on a MS SBS machine where every morning the datastore for the exchange mailboxes dismounts itself. We believe the issue is that it has grown too large over time and needs cut down a bit. As part of this we have removed (purged) some mail files that were no longer needed, which should have given us a saving of roughly 3GB (more than enough saving for what we need). So I deleted the mailboxes, then purged them and noticed that the .edb file was still reporting the same size, I dismounted and remounted it to see if that would have any effect but it did not. Am I missing a step? I have read online that you can run offline defrag on the file but that seems to only save you a small amount of whitespace. Any help would be greatly appreciated.

  Read the article

• "Warning: hostname localhost does not resolve to address ::1: No address associated with hostname" inside an openVZ/Debian container

  - by frlan

  I'm getting the mesage regulary inside mail.log from postfix. In special, but not only, at mails send received mailman. warning: hostname localhost does not resolve to address ::1: No address associated with hostname ::1 as well as 127.0.0.1 are defined as localhost inside /etc/hosts -- as provided by openVZ. Actually inside /etc/hosts these is configured (I removed special domains and IP for reasons): fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters 2a01::<some IPv6> host.example.org host example.org 127.0.0.1 localhost.localdomain localhost # Auto-generated hostname. Please do not remove this comment. xxx.xxx.xxx.xxx host.example.org host example.org ::1 localhost ip6-localhost ip6-loopback And this seems to work: $ host localhost localhost has address 127.0.0.1 localhost has IPv6 address ::1 On this box bley is also running.

  Read the article

• Outlook 2010 stopped marking messages as read after reading them

  - by dunxd

  Yesterday I noticed that Outlook 2010 had stopped marking messages as read unless I right click and select Mark as Read. I have checked the Reading Panel settings (it's set to 0 seconds), but I don't use the reading panel to read my mail. When I open a message by doubleclicking it, then close it again, the message is still marked as Read. Outlook 2010 is connecting to Exchange Server 2003. This was working fine until yesterday. As far as I know there have been no config changes at either the client or server end.

  Read the article

• Need to set up a proxy on Linksys E3200 to filter home internet

  - by Justin Amberson

  the fact that I have a Linksys E3200 may not be important. I can configure the router through the web interface, but I don't know the things I will be toggling are called. I already do simple port forwarding to access applications on my Mac remotely. So router admin is not something I technically need explained. I'm looking to running a proxy on my home computer, that filters all HTTP traffic that goes through my router. So if my daughter is on her iPad and accesses Safari, my Mac will be the judge of the validity of the request. I need something like NetNanny I guess, but local. Actually, anything that can just filter all port 80 traffic that runs locally, but maybe validates with a password? I truly truly hope this question falls within the bounds of Serverfault. I'm not a total internet newb but I'm at a loss for what to Google. If possible answer this question: Is there a webapp that can listen on port 80, and validate requests to port 80 with a password? If so, can I forward all traffic on port 80 to my Mac, to be re-routed to the user? Is this the same as a VPN? Thank you for your help. Justin

  Read the article

• SMTP 25 blocked externally

  - by Jeff

  not sure how to title this question... we run an exchange server with around 80 internal users, all outgoing mail is relayed off a smart host (ISP smtp server) so nothing is actually sent to the world via our server. i wanted to check the server, locally i can telnet to port 25 with no issues and receive the esmtp service ready reply. whenever i do it from an external address (off our local network) i receive unable to connect error 10060. can this cause problems with SPF records, and reverse DNS ? should my exchange server be able to accept smtp requests, requiring authentication before i am able to send from external addresses? if so how... also the exchange server is behind a NAT (asa) device, more than likely thinking that the nat is not configured to route the smtp 25 request to the exchange server.. thanks

  Read the article

• Using iptables to make a VPN router

  - by lost_in_the_sauce

  I am attempting to make a VPN connection to a third party VPN site, then forward traffic from my internal computers (ssh and ping for now) out to the VPN site using IPTables. 3rd Party <- (tun0/eth0)Linux VPN Box(eth1) <- Windows7TestBox I am running on CentOS 6.3 Linux and have two network connections eth0-public eth1-private. I am running vpnc-0.5.3-4 which is currently connecting to my destination. When I connect I am able to ping the destination IPAddresses but that is as far as I can get. ping -I tun0 10.1.33.26 success ping -I eth0 10.1.33.26 fail ping -I eth1 10.1.33.26 fail I have my private network Windows 7 test box set up to have the eth1 (private) network of my VPN Server as its gateway and can ping him fine. I need IPTables to send the Windows 7 traffic out the VPN tunnel. I have tried for a few days many different IPTables configurations from this site and others, either the other examples are too simple or overly complicated. The only thing this server is doing is connecting to the VPN and forwarding all traffic. So we can "flush" everything and start from scratch here. It is a blank slate. #!/bin/bash echo "Define variables" ipt="/sbin/iptables" echo "Zero out all counters" $ipt -Z $ipt -t nat -Z $ipt -t mangle -Z echo "Flush all active rules, delete all chains" $ipt -F $ipt -X $ipt -t nat -F $ipt -t nat -X $ipt -t mangle -F $ipt -t mangle -X $ipt -P INPUT ACCEPT $ipt -P FORWARD ACCEPT $ipt -P OUTPUT ACCEPT $ipt -t nat -A POSTROUTING -o tun0 -j MASQUERADE $ipt -A FORWARD -i eth1 -o eth0 -j ACCEPT $ipt -A FORWARD -i eth0 -o eth1 -j ACCEPT $ipt -A FORWARD -i eth0 -o tun0 -j ACCEPT $ipt -A FORWARD -i tun0 -o eth0 -j ACCEPT Again I have done many variations of the above and many other rules from other posts but haven't been able to move forward. It seems like such a simple task, and yet....

  Read the article

• Are there any tutorials on web hosting at home? [closed]

  - by Arturs Lapins

  I want to host at home and I have done it before but I want to setup a server not just hosting on my windows 7. I know the risks and its better to just buy from hosting providers etc. I'm interested to host at home and I can't find any okay tutorial using unix, ubuntu server or whatever is the best. I want to see how you can install your mail server and make it work on your host and also ftp and all that interesting stuff. You people got any links or what?

  Read the article

• how to stop deferred emails

  - by Will K

  I have a postfix mail gateway. At the same time, every other host is set to use this gateway as the relay. We have some automated outgoing emails sent from some hosts. I believe the gateway trys to send a deferred status back to the system started this. But that system is a null client, which sends but not receive any email Is there anyway to stop sending the deferred status? e.g. postfix/smtp[35725]: 2F6A155C256: to=, relay=none, delay=260862, delays=260862/0.01/0/0, dsn=4.4.1, status=deferred (connect to orange.mydom.com[192.168.1.5]:25: Connection refused) Thanks

  Read the article

• Connect from Mac OS X to Windows 7 Desktop

  - by jrn

  I am trying to connect from my MacBook to my Windows 7 machine within my own network - if it will work from outside my network that's a plus but no need to have. My Windows 7 machine is freshly installed with Windows 7 Home Premium. It runs the built-in firewall with no settings changed so far as well as Microsoft Security Essentials. So far I tried CoRD and Microsofts Remote Desktop Connections to connect from my Mac to my Windows machine without any success. I did try and disabled the firewall on my Windows machine but could not connect either. The reason I did this was to check wether there is a Windows firewall setting preventing me from connecting. On top of that I manually started the Remote Desktop Services and Remote Desktop Configuration within services.msc. Is there anything else I have to enable for a remote desktop connection? Could there be any router setting I have to tweak? Since I do not want to connect from outside my own network I thought I don't have to do any port forwarding. The error messages I retrieve are all connection timeouts. I can however ping the hostname and/or IP address. Any help would be greatly appreciated. Thanks a lot, jrn

  Read the article

• Is there any automatic Windows software to check status of website..

  - by user59280

  Is there any automatic Windows software application to check status of website and alert me through mail or message or trigger am alarm.. Example: Consider I am waiting to buy a new latest movie ticket online (through) and the ticket booking has not been informed properly (online booking is opening at a random time). In this situation I will be forced to slave for my PC to get the tickets. To avoid such situation, can you suggest me a software? So I need a software which will alert me when the online booking is open.. Can anyone please help me?

  Read the article

• DNAT from localhost (127.0.0.1)

  - by pts

  I'd like to set up a TCP DNAT from 127.0.0.1, port 4242 to 11.22.33.44, port 5353 on Linux 3.x (currently 3.2.52, but I can upgrade if needed). It looks like the simple DNAT rule setup doesn't work, telnet 127.0.0.1 4242 hangs for a minute in Trying 127.0.0.1..., and then it times out. Maybe it's because the kernel is discarding the returning packets (e.g. SYN+ACK), because it considers them Martian. I don't need an explanation why the simple solution doesn't work, I need a solution, even if it's complicated (e.g. it involves creating may rules). I could set up a usual DNAT from another local IP address, outside the 127.0.0.0/8 network, but now I need 127.0.0.1 as the destination address. I know that I can set up a user-level port forwarding process, but now I need a solution which can be set up using iptables and doesn't need helper processes. I was googling for this for an hour. It was asked multiple times, but I couldn't find any working solutions. Also there are many questions about DNAT to 127.0.0.1, but I don't need that, I need the opposite.

  Read the article

• What's an alternative to using public folders (in Outlook)?

  - by Ivo Flipse

  My colleagues abuse our mail servers public folders to store (old) emails so that everyone can read them using IMAP. I'm looking into good alternatives after reading this Tech Republic article: "10 reasons why you should begin phasing out Exchange public folders" The most important thing they need is access to emails from multiple computers without overloading our network. So do you have any suggestions for alternatives? If there's a nice combination with some CRM system it would be interesting too. Note: this doesn't have to be freeware, usability and efficiency are more important. The solution has to be Windows 32 bit only

  Read the article

• Postfix does not get external emails

  - by Marks

  Hi there. I have a small vserver(ubuntu), on which i want to run mailman and therefore have to configure postfix. I already configured postfix to send mail per relay over gmail (server-ext.). I also receive local emails (server-server), but i dont get emails from ext. (ext. - server). I have a domain routed to the vserver. But when i send an email from external (e.g. from gmail) to [email protected] i don't get it into the inbox. But there is also no error return message i get to my gmail account. What could be a possible problem? Do i have to configure email revieving from external somewhere? Thanks for any help.

  Read the article

• Stop Metro on W8 from minimizing on dual screens

  - by Pestario

  I'm running Windows 8 with two screens, and have set it so that I have Metro on my secondary screen, because I thought that I could have that visible while I was working on other things on the main screen. The problem is, as soon as I click on something on the main screen, Metro goes away on my secondary screen. Is there any way to prevent this from happening?? I would like to be able to see f.ex the clock, notifications on mail/messaging etc. while I'm working on things.

  Read the article

• CNAME lookup failed temporarily. (#4.4.3)

  - by klickverbot

  A friend of mine just told me that he can't send mails to accounts on one of my servers via the SMTP server provided by his ISP. The error message in the bounce he gets reads: Hi. This is the qmail-send program at aon.at. I'm afraid I wasn't able to deliver your message to the following addresses. This is a permanent error; I've given up. Sorry it didn't work out. <[email protected]>: CNAME lookup failed temporarily. (#4.4.3) I'm not going to try again; this message has been in the queue too long. Any ideas what could be the reason for this? I have double-checked the DNS records for my domain, but they seem perfectly fine, and from any other mail servers I tested, delivery works flawlessly…

  Read the article

• Finding a way to enter gmail in Company

  - by stckvrflw1

  Hello all, I am entering network over DNS's of my company. Here my company blocks lots of IP's for reasons like entertainment, sports, music, messaging boards etc. General e-mail is also one of those topics and I can't enter gmail.com. The proxy sites are also blocked in the company and the one's I have found (by spending much afford) are not accepting cookies. Also I am not able to enter the gmail from Igoogle too, this is also blocked. How can I enter gmail ? Thanks.

  Read the article

• Need reasonably priced router with QoS support [closed]

  - by ULTRA_POROV

  I dont need wireless. I am expecting very heavy traffic, with possibly thousands of tcp connections open at one time. This would require that the router has good hardware. I also need to limit the different services i will provide. Lets say i need to guarantee 60% of all the bandwidth to HTTP, 10% FTP, and 10% for Mail... So the router software must have flexible QoS options as well. I don't know which one to chooose, because this information is usually not given on the router specs.

  Read the article

• How to achieve in-folder discussions with IMAP (skip SMTP send, Thunderbird)?

  - by lkraav

  Does anyone know a good way to achieve replying to a message into the same IMAP folder without sending another duplicate copy over SMTP? This is to be achieved with a conventional GUI mail client, especially Thunderbird. Goal is to have an in-folder conversation. This is possible with shared IMAP folders, with per-user Seen indices, where subscribed recipients are guaranteed to see the new messages without them arriving from internet. Thunderbird is capable of storing a copy of a reply in the same folder as original message (Account Options), which is half way there. Just pressing Save sends the message into Drafts and that is probably an even bigger patch to try to put a "draft message" into the same folder as original. All options, client, server or logic-wise are an acceptable answer, including programming i.e. patching/creating add-on for Thunderbird.

  Read the article

• Prevent email to root@domain

  - by kml

  I'm running Ubuntu Server 12.04 as a web server and use Exim4 for sending confirmation emails and such. Is there a way to set a system-wide email address for the root user? In other words, I'd like ALL email to go to a different address rather than [email protected]. For example, this command... echo "test" | mail -v -s test root ...would go to a different address, as well as all cron tasks that root executes: # m h dom mon dow user command 17 * * * * root cd / && run-parts --report /etc/cron.hourly 25 6 * * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.daily ) 47 6 * * 7 root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.weekly ) 52 6 1 * * root test -x /usr/sbin/anacron || ( cd / && run-parts --report /etc/cron.monthly )

  Read the article

• What is the best appliance you've used?

  - by phuzion

  Post your favorite appliances or "all-in-one" programs. Whether it runs in a virtual machine, or on its own hardware, it all goes. My submission is Untangle. It's an open source network gateway (their term). Essentially, it can run a plethora of things that you may otherwise end up buying another appliance for: Web filtering logging mail spam filtering phishing monitor spyware blocking VPN You name it, it's all there. Best of all, it's mostly free. A few appliances have annual costs due to inherent licensing or subscription costs. If you are looking for a new network perimeter device, definitely check it out. The underlying OS doesn't matter, because it's the application we want to praise, not the OS beneath it.

  Read the article

• 56.6 Modem with CallerID

  - by Fuod

  Does anyone still know anything about the 56.6 modems? I'm looking for one that is easy to access via C#/VB.Net, has Caller ID and is either low-profile or USB. Also that neat little feature that lets the modem block the call from the phone (pass-through) until it has received the CallerID info would be really nice! Obviously I could just go to Best Buy and get what they have but I have no way of knowing how friendly it would be to write code for and I don't want to make multiple trips returning/exchanging etc. I'm not going to be doing anything with voice or voice mail, just recording the number from CallerID. Thanks!

  Read the article

• Configuring two subnets with two NICS. Access from a NAS to the internet

  - by archipestre

  I am having trouble configuring my NAS. I have a DSL router with WIFI (192.168.1.1) in my flatmates room. In my room I have a server with two NICS: 1) wlan0 (192.168.1.2) that connects to the DSL router via wireless 2) em1 (192.168.0.1) that connects to the NAS (192.168.0.20) with a crossover cable. I have Fedora 17 and I have enable packet forwarding. My IP configuration is as follows: WLAN0 inet 192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.255 EM1 inet 192.168.1.2 netmask 255.255.255.0 broadcast 192.168.1.255 My routing table looks like: Destination Gateway G enmask Flags Metric Ref Use Iface 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 wlan0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 em1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 I have enable a static route in the DSL server: Status Network Destination Subnet Mask Interface Gateway Remove Edit Active 192.168.0.0 255.255.255.0 LAN 192.168.1.2 From my server I can ping the DSL router and the NAS. From the NAS I can ping both NICS of the server. However the NAS is unable to ping the DSL router or any address in the Internet. Any idea of what is wrong. Thank you in advance

  Read the article

• Remote Linux system via Windows 7

  - by kaila

  I have a dual boot with Windows 7 and Fedora. Though I can long into both without any problems, I am trying to log in to the linux account via the Windows account. Is that possible? Or, is it possible to access my university's linux server via telnet from home? I did so and got an error, with cold not connect to port 23 message. Also, since most of my mail accounts are on Windows, the passwords to which I have forgotten, I would prefer working on a ;remote' connection.

  Read the article

• Intermittent 403 errors when using allow to limit access to url with both explicit IP and SetEnvIf

  - by rbieber

  We are running Apache 2.2.22 on a Solaris 10 environment. We have a specific URL that we want to limit access to by IP. We recently implemented a CDN and now have the added complexity that the IP's that a request are shown to be coming from are actually the CDN servers and not the ultimate end user. In the case that we need to back the CDN out, we want to handle the case where either the CDN is forwarding the request, or the ultimate client is sending the request directly. The CDN sends the end user IP address in an HTTP header (for this scenario that header is called "User-IP"). Here is the configuration that we have put in place: SetEnvIf User-IP (\d+\.\d+\.\d+\.\d+) REAL_USER_IP=$1 SetEnvIf REAL_USER_IP "(10\.1\.2\.3|192\.168\..+)" access_allowed=1 <Location /uri/> Order deny,allow Allow from 10.1.2.3 192.168. allow from env=access_allowed Deny from all </Location> This seems to work fine for a time, however at some point the web server starts serving 403 errors to the end user - so for some reason it is restricting access. The odd thing is that a bounce of the web server seems to resolve the issue, but only for a time - then the behavior comes back. It might be worthwhile to note as well that this URL is delegated to a JBoss server via mod_jk. The denial of access is, however; confirmed to be at the Apache layer and the issue only seems to happen after the server has been running for some time.

  Read the article

• /etc/hosts file for a multi-homed, multi-domain machine?

  - by threecheeseopera

  I have a server (debian) with two network interfaces that I would like to host multiple services and domains on; it is not entirely clear to me how the hosts file should be set up. Example: eth0, bound to WAN interface 1.2.3.4: mail.example.com www.example.com eth0:1, bound to WAN interface 1.2.3.5: www.other-domain.com eth1, bound to LAN 192.168.1.123: some-clever-hostname What should my hosts file look like? (including localhost,localhost.localdomain, etc.) Should I use DNS for some of these entries? Which ones? Thanks!

  Read the article

< Previous Page | 231 232 233 234 235 236 237 238 239 240 241 242  | Next Page >