Search Results

Search found 7776 results on 312 pages for 'configure'.

Page 238/312 | < Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >

• How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

  - by piobyz

  I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

  Read the article

• How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

  - by piobyz

  I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

  Read the article

• How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

  - by piobyz

  I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

  Read the article

• How do I install the evaluation version of Windows Server 2012R2 VHD within a Windows Server 2008R2 Hyper-V system?

  - by Paul Hale

  I have a windows server 2008R2 running hyper-v. I have downloaded the Windows Server 2012RC DC Version from here... http://technet.microsoft.com/en-us/evalcenter/dn205286.aspx I am "forced" to install a download app that copy's a .vhd file to my chosen directory. The instructions on this page... http://technet.microsoft.com/library/dn303418.aspx say... To install the VHD Download the VHD file. Start Hyper-V Manager. On the Action menu, select Import Virtual Machine. Navigate to the directory that the virtual machine file was extracted to and select the directory (not the directory where the VHD file is located). Select the Copy the virtual machine option. Confirm that the import was successful by checking Hyper-V Manager. Configure the network adapter for the resulting virtual machine: right-click the virtual machine and select Settings. In the left pane, click Network Adapter. In the menu that appears, select one of the network adapters of the virtualization server, and then click OK. Start the virtual machine. Where it says "Navigate to the directory that the virtual machine file was extracted to and select the directory (not the directory where the VHD file is located). Select the Copy the virtual machine option." Well nothing has been extracted as far as I can tell? and if it has, I have no idea where or what im looking for? I tried creating a new VM and using the downloaded .vhd file but I got an error saying that the .vhd file is an incompatible format. Can anybody help me out please? Thanks, Paul

  Read the article

• php5-mysqlnd on debian wheezy/sid?

  - by Joseph

  I am trying to install php5-mysqlnd on a fresh install of Wheezy (/etc/debian_version refers to it as wheezy/sid) and I'm having a problem: root@debian:/var/www/lottery1# apt-get install php5-mysqlnd Reading package lists... Done Building dependency tree Reading state information... Done php5-mysqlnd is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. 1 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? Y Setting up php5-mysqlnd (5.4.0-3) ... ucfr: Attempt from package php5-mysqlnd to take /etc/php5/mods-available/mysql.ini away from package php5-mysql ucfr: Aborting. dpkg: error processing php5-mysqlnd (--configure): subprocess installed post-installation script returned error exit status 4 Processing triggers for libapache2-mod-php5 ... configured to not write apport reports Reloading web server config: apache2. Errors were encountered while processing: php5-mysqlnd E: Sub-process /usr/bin/dpkg returned an error code (1) It seems there is some sort of conflict with the php5-mysql package, but I still get this error even after removing (with --purge) the php5-mysql package. Any thoughts? I'm trying to run a web tool that makes heavy use of mysqli_result::fetch_all(). Thanks!

  Read the article

• VPS with Plesk, one ip, and godaddy (definely need help)

  - by Francesco

  Hi there, here's my situation : i've Plesk 8.3.0 with one IP and i've registered my domains at godaddy.com My problem : i cannot figure out how to configure plesk and godaddy to have my domains (6) properly working into the VPS. i've only one IP, so i can't have my personal NS and need to use godaddy ns. But.. how do i set all the stuff ? I've made a try but it's not working. Please take a look : This is an example of how the domain i'm actually working on is configured On Plesk : Host Record type Value 1.2.3.4 / 24 PTR mydomain.com. ftp.mydomain.com. CNAME mydomain.com. mail.mydomain.com. A 1.2.3.4 ns.mydomain.com. A 1.2.3.4 mydomain.com. NS ns.mydomain.com. mydomain.com. A 1.2.3.4 mydomain.com. MX (10) mail.mydomain.com. webmail.mydomain.com. A 1.2.3.4 www.mydomain.com. CNAME mydomain.com. On godaddy,(Total DNS Control) for the same domain i have this setup : A (Host) Host Points To TTL Actions * 1.2.3.4 1 Hour CNAMES (Aliases) Host Points To TTL Actions e email.secureserver.net 1 Hour email email.secureserver.net 1 Hour ftp @ 1 Hour imap imap.secureserver.net 1 Hour mail pop.secureserver.net 1 Hour mobilemail mobilemail-v01.prod.mesa1.secureserver.net 1 Hour pda mobilemail-v01.prod.mesa1.secureserver.net 1 Hour pop pop.secureserver.net 1 Hour smtp smtp.secureserver.net 1 Hour webmail webmail.secureserver.net 1 Hour www @ 1 Hour MX (Mail Exchange) Priority Host Goes To TTL Actions 10 @ mailstore1.secureserver.net 1 Hour 0 @ smtp.secureserver.net Host Points To TTL Actions @ ns53.domaincontrol.com @ ns54.domaincontrol.com What should i correct ? Thanks for helping me Francesco

  Read the article

• Exchange Online SMTP Not Working With Any Email Client

  - by emre nevayeshirazi

  I am trying to switch our company mail server to exchange online. I have successfully added my domain and users and can send and receive mails through Outlook Web App. I can also send and receive if I configure my Outlook 2013 client using Exchange protocol. However, some folks in company are using Thunderbird and some old Outlook Clients. For those, I tried to connect to Exchange via IMAP/SMTP. This is what I use, For incoming, IMAP / Port : 993 with SSL / Host : outlook.office365.com For outgoing, SMTP / Port : 589 with TSL / Host : smtp.office365.com I can receive emails, however I could not be able to send emails. I keep getting An error occurred while sending mail. The mail server responded: 4.3.2 Service not active. Please verify that your email address is correct in your Mail preferences and try again. My username and password are correct, I am using my mail address as my username to mailbox. I also tried sending mail via C# application which was working for outlook.com and gmail.com SMTP settings. It also fails to send emails and returns the same error code. I thought TB and other old clients such as Office 2003 might not support Exc. Online so I tried same settings in Office 2013. It successfully connected my mailbox when checking for configuration but failed in sending test message and returned the same error code. Configuration for incoming and outgoing mailbox are taken from here. They are also available on Office 365 user page and they are same. What could be the reason for error ?

  Read the article

• IIS7 - Web Deployment Tool - SetParam/SetParamFile to set http and https bindings + Cert

  - by Andras Zoltan

  Hi, we're currently using the MS Web Deployment Tool to sync a live website and some WebServices from a staging box to two live servers. The staging box hosts the site on any IP on port 17000, whereas the two live servers are load-balanced and have a different IP for each of them. At present, I generate two separate packages for deployment - one for each machine - using the sync operation and specifying a DestinationBinding parameter as follows: msdeploy -verb:sync -source:WebServer,computerName=localhost -dest:package="machinename.zip" -setParam:type="DestinationBinding",scope="SiteName",value="ip_address:port:". (Split across multiple lines to make it easier to read!) I run this twice, with a different target filename and ip address for each of the two machines. When it comes to deployment, I simply do a sync from each package to its respective live site. I know, I know - I should be able to do it by generating one parameterised package and then perhaps using the SetParamFile switch for each of the two Servers - believe me I'd like to, but the documentation on doing this is frankly non-existent. Now I need to configure and deploy both HTTP and HTTPS binding for this site; including also the ssl cert that is to be used. I've added an SSL binding for the site on the staging box - which uses a development cert (which will need to be replaced - or should the staging box be using the live cert?), and now the above command line has the effect of replacing the target IP on both http and https entries. It appears that I cannot specify multiple bindings plus the cert information in the DestinationBinding value in the -setParam above, so anyone know how would I go about doing this? Any help greatly appreciated.

  Read the article

• Problem with network policy rule in Network Policy Server

  - by Robert Moir

  Trying to configure RADIUS for a college network, and have run into the following frustration: I can't set an "AND" condition for group membership of authenticated objects in the network policy rules, e.g. I'm trying to create a NPS rule that says, essentially "IF user is a member of [list of user groups] And is authenticating from a computer in [wireless computer group] then allow access. The screenshot above is the rule I am having trouble with. It does not work as written. The rule underneath it, which is identical in every aspect except the conditions rule, does work. I've tried changing the non-working rule to define each set of groups as "Windows group" rather than specifically as machine and user groups, with no change. With the "faulty" rule enabled and the working one disabled, any attempt to login with a valid account from a machine that is in the wireless computers group gives a 6273 audit event in the windows event log: Reason code 66 - "the user attempted to use an authentication method that is not enabled on the matching network policy". Disabling the "faulty" rule, enabling the other rule and logging in with the same account and computer works just fine.

  Read the article

• Multiple Internet connections, multiple networks and split access in Linux

  - by Swapneel Patnekar

  I am having trouble setting up multiple internet connections for split access in Linux. We have 3 internet connections from 3 different ISP's. We want to configure our Linux gateway machine such that our three internal networks 10.2.1.0/24, 192.168.20.0/24 & 192.168.2.0/24 use ISP1, ISP2 and ISP3 respectively in a split access manner. Outlined below is the layout/settings, Interfaces of the Linux Gateway connected to Routers: eth0: 10.1.1.2<---------->10.1.1.1(Internal Interface of ADSL Router)[ISP1] eth1: 192.168.15.2<------>192.168.15.1(Internal Interface of 3G Router)[ISP2] eth3: 192.168.1.2<------->192.168.1.1(Internal Interface of ADSL Router)[ISP3] Kindly note that none of the interfaces in the Linux gateway has a public static IP address. Routers of ISP1 and ISP2 get assigned a dynamic public IP address when connected to the Internet, router of ISP3 has been assigned a public static IP address. Interface of Linux gateway connected to a switch, eth4: 10.2.1.1(LAN Interface for ISP1) eth4:0 192.168.20.1(LAN interface for ISP2) eth4:1 192.168.2.1(LAN Interface for ISP3) eth4:0 & eth4:1 are virtual interfaces with eth4 being the interface connected physically. Based on http://linux-ip.net/html/adv-multi-internet.html I've set the following routes, ip route flush table 4 ip route show table main | grep -Ev ^default | while read ROUTE ; do ip route add table 4 $ROUTE done ip route add table 4 default via 192.168.15.1 ip rule add fwmark 4 table 4 ip route flush cache Additionally, using the following iptables rules to mark & route packets as per the guide mentioned above : http://pastebin.com/KzWHFGJA At this point, computers from 192.168.2.0/24 network are successfully able to reach the Internet through ISP3. 192.168.20.0/24 and 10.2.1.0/24 are unable to access the Internet through ISP1 and ISP2 respectively. Any inputs will be much appreciated !

  Read the article

• Compile PHP 5.3.2 with intl extension on Snow Leopard 10.6.3

  - by fsb

  Does anyone have some tips on compiling PHP's intl extension on PHP? I'm getting compile errors each way I try it and I've been googling for ages and getting nowhere. Any help greatly appreciated. When make gets to the huge gcc command to compile libphp5.bundle, I get the following error: Undefined symbols: "___gxx_personality_v0", referenced from: icu_4_2::MessageFormatAdapter::getArgTypeList(icu_4_2::MessageFormat const&, int&)in msgformat_helpers.o _umsg_parse_helper in msgformat_helpers.o _umsg_format_arg_count in msgformat_helpers.o _umsg_format_helper in msgformat_helpers.o CIE in msgformat_helpers.o ld: symbol(s) not found collect2: ld returned 1 exit status make: *** [libs/libphp5.bundle] Error 1 My compile commands are: MACOSX_DEPLOYMENT_TARGET=10.6 CFLAGS="-arch x86_64 -g -Os -pipe -no-cpp-precomp" CCFLAGS="-arch x86_64 -g -Os -pipe" CXXFLAGS="-arch x86_64 -g -Os -pipe" LDFLAGS="-arch x86_64 -bind_at_load" export CFLAGS CXXFLAGS LDFLAGS CCFLAGS MACOSX_DEPLOYMENT_TARGET ./configure --prefix=/usr \ --mandir=/usr/share/man \ --infodir=/usr/share/info \ --sysconfdir=/private/etc \ --with-apxs2=/usr/sbin/apxs \ --enable-cli \ --with-config-file-path=/etc \ --with-libxml-dir=/usr \ --with-openssl=/usr \ --with-zlib=/usr \ --with-bz2=/usr \ --with-curl=/usr \ --with-gd \ --with-jpeg-dir=/src/jpeg/jpeg-local \ --with-png-dir=/usr/X11R6 \ --with-freetype-dir=/usr/X11R6 \ --with-xpm-dir=/usr/X11R6 \ --with-ldap=/usr \ --with-ldap-sasl=/usr \ --enable-mbstring \ --enable-mbregex \ --with-mysql=mysqlnd \ --with-mysqli=mysqlnd \ --with-pdo-mysql=mysqlnd \ --with-mysql-sock=/var/mysql/mysql.sock \ --with-iodbc=/usr \ --enable-shmop \ --with-snmp=/usr \ --enable-soap \ --enable-sockets \ --enable-sysvmsg \ --enable-sysvsem \ --enable-sysvshm \ --with-xmlrpc \ --with-iconv-dir=/usr \ --with-xsl=/usr \ --with-pcre-regex=/src/pcre/pcre-local/usr/local \ --with-pcre-dir=/src/pcre/pcre-local/usr/local \ --with-icu-dir=/usr/local \ --enable-intl export EXTRA_CFLAGS="-lresolv" make

  Read the article

• PostgreSQL failover cluster on Windows Server

  - by user36997

  We are looking for advice on how to setup a basic failover cluster for our application: We will be using 4 machines running Microsoft Windows Server (most probably 2003). All four will always run our application, which is essentially a web service. Load balancing is "outsourced" - somebody else handles the distribution of the web requests among the servers. Only one of the servers will be running the PostgreSQL server actively at any given time. Another server (of the four) also has the DB installed, but is on standby/passive. The DB data is stored on shared storage. No copying data between servers. Reads are done very frequently by many end-users, and in rather small chunks of data. Writes are done much less frequently, by less users, and in very large bulks of data. Now, how can one configure Microsoft Cluster Service to keep only one instance of the DB server and 4 instances (1 per server) of our application at all times? And does PostgreSQL integrate neatly with MSCS at all? Update: Instead of keeping the data on shared storage, I also consider using log shipping to replicate data on a couple of DB servers. There are two issues with this option: Log shipping only makes sure that I have a second server that gets all of the data and is ready to take over. How do I implement the actual failure detection and failover switch? Switching back: Suppose the master fails and the system automatically fails over to the slave, and later the master comes back online. I understand that with WAL shipping this will require to reconfigure the log shipping once again, and that switching back is far from seamless. Is that so?

  Read the article

• Sync clock on Windows XP machine to external (non-domain, non-workgroup) Windows Server 2008 R2 machine

  - by Eric

  I have two machines and I'd like their clocks to be in sync for various reasons. Machine 1 is an XP machine located in the office. Machine 2 is a VPS hosted by a third party running Windows Server 2008 R2. These machines are not in any kind of workgroup or on a domain together. They are completely separate machines. Machine 2 is currently syncing once a week to time.windows.com. The clock on Machine 2 does seem to wander a bit within that week interval. What I would like to do is have Machine 1 set its clock based on the clock of Machine 2. I have tried configuring w32tm on the XP machine. This is what I used for configuration: w32tm /config /syncfromflags:manual /manualpeerlist:"<ip address of machine 2>" However, whenever I issue the /resync command I get "The computer did not resync because no time data was available". I have made sure to start the windows time service on machine 2, and I have added firewall exceptions for UDP port 123. Is there something I need to configure on Machine 2 (other than just starting the time service) in order to get it to respond? Edit: I have also run w32tm /config /reliable:YES /update on Machine 2. I am still getting "The computer did not resync because no time data was available". Is there something else I'm missing?

  Read the article

• Trying to use a SmartHost with my Exchange 2010 server

  - by Pure.Krome

  Hi folks, I'm trying to use a SmartHost with my Exchange 2010 Server. SmartHost details: Secure SMTPS: securemail.internode.on.net 465 <-- Note: that's port 465 Configure your existing SMTP settings (in your email program) to: use authentication (enter your Internode username and password, enter your username as [email protected]). enable SSL for sending email (SMTPS). So I've added the smart host details to my Org Config -> Hub Transport. I then used PowerShell to add the port:- Set-SendConnector "securemail.internode.on.net" -port 465 I've then added my username/password (as suggested above) to the SmartHost as Basic Authentication (with no TLS). Then I try sending an email and I get the following error message :- 451 4.4.0 Primary target IP address responded with: "421 4.4.2 Connection dropped due to ConnectionReset." So i'm not sure how to continue. I also tried ticking the TLS box but stll I get the same error. If i don't use SMTPS (secure SMTP, on port 465) and use basic SMTP on port 25 with no Authentication, email gets sent. Any ideas? EDIT: Btw, I can telnet to that server on port 465 from my mail server .. just to make sure i'm not getting firewall'd, etc.

  Read the article

• Windows XP laptop doesn't appear in WSUS All computers list

  - by George

  I have this one laptop that doesn't appear in WSUS all computers list. We have about 23-25 PCs/laptops/servers in the network, all, but one are listed in WSUS. This is what I have done so far: 1) Changing Updates on local PC: Go to your Windows XP client and start a new Microsoft Management Console (MMC). At Start, Run, type MMC. Use Ctrl+M to add a new snap-in. Click Add, and then add the Group Policy Object Editor for the Local Computer. Click Close, and then click OK. Expand the Local Computer Policy. Under Computer Configuration, go to Administrative Templates, Windows Components, Windows Update. In the right-hand pane, double-click Specify intranet Microsoft update service location. Configure the settings to reflect my WSUS server. Click OK and then close the MMC without saving it. executed wuauclt.exe /detectnow 2) Edited registry key to be pushed to the PCs using GPO [HKEY_LOCAL_MACHINE\SOFTWARE\Policies\Microsoft\Windows\WindowsUpdate] "WUServer"=http://wsusserver "TargetGroupEnabled"=dword:00000001 "TargetGroup"="WINXP" "WUStatusServer"=http://wsuswerver 3) executed wuauclt /resetauthorization /detectnow 4)Synchronised and refreshed the group I am running out of ideas here. The client is running Windows XP pro, WSUS version is 3.0 and is running on Windows 2008 R2 64-bit. Please, help! Thanks! EDIT 13.IX.2012 @ 15.40 I should have also mentioned that we do have a Windows Update GPO for workstations group and that laptop is a part of that group.

  Read the article

• Setup Entourage for Exchange via HTTP communication

  - by Johandk

  Our ISP set up a hosted exchange server for all our mail. I've setup all our Outlook users with no problems. We have two people using Mac OSX Leopard and Entourage. Entourage has the option of adding an Exchange account, but I have no idea how to tell it to connect to exchange via HTTP. Heres an excerpt from the client setup docs the hosting company sent me for Outlook: 1 .Go to control panel 2. Select ‘Mail’ 3. Select ‘Email accounts’ Under the E-mail tab select ‘New’ Select ‘Manually configure server settings......’ - click next Select ‘Microsoft Exchange’ – click next Complete details as below with Microsoft Exchange Server as: [server address] Do not select ‘Check Name’. Instead select ‘More Settings’. Go to the Connection tab, and select the bottom option ‘Connect to Microsoft Exchange using HTTP’. And then select the ‘Exchange Proxy Settings’ button. Enter Proxy server for Exchange Check Only connect to proxy servers that have this principal name in their certificate, Enter msstd:[servername] Proxy Authentication - select Basic Authentication Select OK, and again, so that you return to the main screen. Now select ‘Check Name’. Enter Username and Password: The username should now be the full name and underlined. If so select next, and then finish. Next time you open Outlook, enter username and password Any help GREATLY appreciated.

  Read the article

• Subversion Edge LDAP (require CAC Certificate not Username and Password)

  - by Frank Hale

  What I've Done: I've successfully installed and configured Subversion Edge 3.1.2 with LDAP support on a Windows 2008 server. I have configured LDAP users and am able to use LDAP credentials to work on repositories just fine. No issues whatsoever. Works great! What I Want To Do: I've been searching for several hours now in hopes to find some information on how to configure Subversion Edge server to require client certificates for user authentication against an LDAP environment. I have not found anything yet that gives me an indication of how to do it. I know there are SVN clients that are capable of prompting for CAC certificates but I cannot figure out how to set my server up to require it. NOTE: CAC authentication is already setup and working in the windows environment. Desired Outcome: When running svn commands that require authentication against my Subversion Edge Server I want it to prompt me for my CAC certificate instead of my Active Directory username and password. If anyone has any information on this I'd greatly appreciate it. EDIT: I'm still digging so if I find out anything I'll update this question with what I found.

  Read the article

• Virtual PC duplication process

  - by Toddintr

  This is the process I use for duplicating a Virtual PC (on Windows 7): 1 - Create a new VPC. 2 - Install Windows 7 on the new VPC. 3 - Configure the new Windows 7 installation (install Windows updates, install applications, etc). 4 - Run Sysprep on the new VPC. 5 - Shut down the new VPC. 6 - Make a copy of the new VPC's VHD file. 7 - Create a new VPC, specify "use existing VHD file" in the wizard and provide the name of the copied VHD file. Above works fine but there is one point that threw me off: During the OOBE for the duplicated VPC, when asked for a user name, I had to specify a different user name than the one I had specified for the base VPC. This makes sense because the copied VPC already has that user name. But what I did not understand is why I was asked for a new user name at all? Is it because it is part of the OOBE process and when the OOBE was designed by Microsoft, they did not think of the fact that base OS images could be copied? Thanks - -Todd

  Read the article

• Ruby Passeger + Nginx or lighthttpi + fgci for shared hosting

  - by devnull

  I have set up a passenger + nginx setup and I plan to offer a free non-commercial hosting (or in fact on the fly deployment) for rack-based frameworks (e.g. camping, sinatra). I am facing an "issue" with passenger. For each application you need to configure nginx.conf (it would be the same with apache so it is not an nginx issue) with: server { ... passenger_base_uri /app1; passenger_base_uri /app2; passenger_base_uri /app3; } Now this is not inherently bad as, in theory, I could allow a user to run just one app on his webspace but even in this case I need to create a new server directory on nginx e.g. (user.domain.com). As this will mainly be used to deploy apps the behavior I am looking at is more the possibility to auto map several apps (e.g. app1, app2, app3, app4) under the same server (your app.com/app1 yourapp.com/app2) without having to update the nginx or apache file each time. This seems to be a limitation in passenger. As such I am thinking about an alternative with lighttpd and fastcgi. Would this allow immediate deployment without touching the lighttpd config file e.g. I create a new directory with app2 and it will run immediately ? What is your experience in performance difference between passenger + nginx vs. lighttpd + fastcgi ? thanks in advance scenario details: on nginx + passenger - user cannot add a new sub-folder and run another sinatra/camping app without declaring the path on nginx.conf and restarting the server; wished behavior with the new setup: - user can add a new folder with a new app and it would run on lighttpd+fcgi without any extra configuration of the web server;

  Read the article

• Centos 6.2 Fresh 'Basic Server' install networking issues

  - by RWC

  I've had a /29 provisioned on a network port for a server and am trying to at least configure the machine so I can ssh into it. It's Centos 6.2 x64 with the Basic Server install. Currently not able to ping gateway or any address for that matter. For reference: Default Interface: em2 Network ID: 66.*.*.0/29 Gateway: 66.*.*.1 Broadcast: 66.*.*.7 Please see my following configs: /etc/sysconfig/network-scripts/ifcfg-em2 DEVICE=em2 NM_CONTROLLED=yes ONBOOT=yes HWADDR=Not Important TYPE=Ethernet BOOTPROTO=none IPADDR=66.*.*.2 PREFIX=29 DNS1=8.8.8.8 DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="System em2" NETMASK=255.255.255.248 USERCTL=no $: route -n Destination // Gateway // Genmask // Flags // Metric // Ref // Use // Iface 66.*.*.0 0.0.0.0 255.255.255.248 U 0 0 0 em2 169.254.0.0 0.0.0.0 255.255.0.0 U 0 1003 0 em2 0.0.0.0 66.*.*.1 0.0.0.0 UG 0 0 0 em2 $: route Destination // Gateway // Genmask // Flags // Metric // Ref // Use // Iface 66.*.*.0 * 255.255.255.248 U 0 0 0 em2 link-local * 255.255.0.0 U 0 1003 0 em2 default 66.*.*.1 0.0.0.0 UG 0 0 0 em2 $: cat /etc/sysconfig/network NETWORKING=yes HOSTNAME=excalibur.domain.com GATEWAY=66.*.*.1 Keep in mind that I cannot even currently ping the gateway which is quite confusing for me. My /etc/hosts are configured correctly with the *.2 address. I'm not concerned with getting all of the addresses on the /29 up and running yet, just one so I can at least ssh in. Thanks! Edit: Adding in ifconfig. $: ifconfig em2 Link encap:Ethernet HWaddr XX:XX:XX:XX:XX:XX inet addr:66.*.*.2 Bcat:66.*.*.7 Mask:255.255.255.248 inet6 addr: UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5536 errors:0 dropped:0 overruns:0 frame:0 TX packets:10 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2599469 (2.4 MiB) TX bytes: 748 (748.0 b) Interrupt:48 Memory:dc000000-dc012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:34 errors:0 etc etc

  Read the article

• Encryption setup for Linux NAS?

  - by Daniel

  There's a bazillion hard disk encryption HOWTOs, but somehow I can't find one that actually does what I want. Which is: I have a home NAS running Ubuntu, which is being accessed by a Linux and a Win XP client. (Hopefully MacOS X soon...) I want to setup encryption for home dirs on the NAS so that: It does not interfere with the boot process (since the NAS it tucked away in a cupboard), the home dirs should be accessible as a regular file system on the client(s) (e.g. via SMB), it is easy to use by 'normal' people, (so it does not require SSH-ing to the NAS, mount the encrypted partition on command line, then connecting via SMB, and finally umount the partition after being done. I can't explain that to my mom, or in fact to anyone.) does not store the encryption key the NAS itself, encrypts file meta-data and content (i.e. safe against the 'RIAA' attack, where an intruder should not be able to identify which songs are in your MP3 collection). What I hoped to do was use Samba + PAM. The idea was that on connecting to the SMB server, I'd have to enter the password on the client, which sends it to the server for authentication, which would use the password to mount the encrpytion partition, and would unmount it again when the session was closed. Turns out that doesn't really work, because SMB does not transmit the password in the plain and hence I can't configure PAM to use the incoming password to mount the encrypted patition. So... anything I'm overlooking? Is there any way in which I can use the password entered on the client (e.g. on SMB connect) to initiate mounting the encrypted dir on the server?

  Read the article

• Accounting setup in freeradius with mikrotik and the "always" module

  - by Matt

  I have a freeradius setup that is being used to provide authentication for users on a wireless network. The access points are all Mikrotik hardware and the users are connected 24/7. We've been using Daloradius with mysql and freeradius 2. The boss wants to use the accounting information and while this is all set up and appears to be working, I've found that not all the accounting information is present. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly. So he started poking around at this link: http://wiki.mikrotik.com/wiki/RouterOs_MySql_Freeradius#Configuring_RouterOs_for_Radius_.26_PPP.2A_AAA And was looking specifically at the following section. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly always fail { rcode = fail } always reject { rcode = reject } always ok { rcode = ok simulcount = 0 mpp = no } However, that link references freeradius 1 and I can't find this in the radius.conf file for freeradius 2. What does it do and could it be a reason I'm missing data? EDIT: I have found one issue. We have a backup freeradius server that is also receiving the accounting packets. Although they are replicating, it's only a master/slave configuration. If the slave receives accounting packets it won't replicate them back to the master. Although I suspect this might solve it, the boss is not convinced due to the always module. Is there anything special I need to configure in the mikrotik AP's or freeradius 2 for clients connected 24/7.

  Read the article

• apache2: ssl_error_rx_record_too_long when visiting port 80?

  - by John

  Hi, I have an Ubuntu 10 x64 server edition machine. I got a second IP and configured /etc/network/interfaces like so (actual IPs and gateways removed): auto lo iface lo inet loopback #iface eth0 inet dhcp auto eth0 auto eth0:0 iface eth0 inet static address [ my first IP ] netmask 255.255.255.0 gateway [ my first gateway ] iface eth0:0 inet static address [ my second IP ] netmask 255.255.255.0 gateway [ my second gateway ] /etc/apache2/ports.conf: Listen 80 NameVirtualHost [ my first IP ]:80 NameVirtualHost [ my second IP ]:80 <IfModule mod_ssl.c> # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to <VirtualHost *:443> # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 NameVirtualHost [ my first IP - some site is running SSL successfully using it ]:443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> /etc/apache2/sites-enabled/mysite.conf: <VirtualHost [my second IP ]:80> ServerName mysite.com Include /var/www/mysite.com/djangoproject/apache/django.conf </VirtualHost> Then when visiting http[mysite].com:80 or http[mysite].com (:// removed because serverfault doesn't allow me to post hyperlinks), I get: An error occurred during a connection to [mysite].com. SSL received a record that exceeded the maximum permissible length. (Error code: ssl_error_rx_record_too_long) My guess is that the configuration file is not being picked up, and apache is therefore looking for the default-ssl file, which is not in conf-enabled. If I were to configure that file properly, it seems I would successfully connect to whatever default directory is specified in the default-ssl file. But I want to connect to my website. Any ideas? Thanks in advance!

  Read the article

• Win 2008 R2 terminal server and redirected printer queue security

  - by Ian

  I have a case where I need a non-priv account to be able to make a modification to the redirected printer. I know, its not advisable but we're not giving them access - changes will be made in code. So, following the docs (http://technet.microsoft.com/en-us/library/ee524015(WS.10).aspx) I modified the default security for new printer queues. This doesnt work though as windows doesn't seem to assign the privs you configure in the printer admin tool to redirected printer queues. As I test I added a non-priv test user to the default security tab in the printer admin tool (control panel - admin tools - printer admin. I assigned it all privs (its a test) and logged the user into the terminal server. The redirected printers duely appeared as usual. However if I open the printer properties - security tab, the user appears in the list of accounts/groups but the options I selected (all privs) are not set. Instead the user special privs box is marked and when I click on 'advanced options' and view them, there is nothing marked. So, something is clearing these options.... the question is, why and how can I convince it not to? Ian

  Read the article

• Output Caching with IIS7 - How To for an dynamic aspx page?

  - by Lieven Cardoen

  I have a RetrieveBlob.aspx that gets some query string variables and returns an asset. Eeach url corresponds to a unique asset. In the RetrieveBlob.aspx a Cache Profile is set. In Web.Config the profile looks like (under system.web tag: <caching> <outputCache enableOutputCache="true" /> <outputCacheSettings> <outputCacheProfiles> <add duration="14800" enabled="true" varyByParam="*" name="AssetCacheProfile" /> </outputCacheProfiles> </outputCacheSettings> </caching> Ok, this works fine. When I put a breakpoint in the code behind of RetrieveBlob.aspx, it gets triggered the first time, and all the other times not. Now, I throw away the Cache Profile and instead I'm having this in my Web.Config under System.WebServer: <caching> <profiles> <add extension=".swf" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".flv" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".gif" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".png" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".mp3" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".jpeg" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> <add extension=".jpg" policy="CacheForTimePeriod" kernelCachePolicy="CacheForTimePeriod" duration="00:08:00" /> </profiles> </caching> Now the caching doesn't work anymore. What am I doing wrong? Is it possible to configure under Caching tag of System.WebServer a Caching Profile for a Dynamic aspx page?

  Read the article

< Previous Page | 234 235 236 237 238 239 240 241 242 243 244 245  | Next Page >