Search Results

Search found 6815 results on 273 pages for 'micro sd card'.

Page 239/273 | < Previous Page | 235 236 237 238 239 240 241 242 243 244 245 246  | Next Page >

• Can I have a single solid state drive and a RAID array on the same machine?

  - by jaminto

  Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

  Read the article

• Windows Server 2008 network speed slow, Xen 3.4.3 HVM ISO

  - by Elliot.Bradshaw

  I've setup a VM running Windows Server 2008 on a host node running Xen 3.4.3-5 and the following kernel: 2.6.18-308.1.1.el5xen #1 SMP Wed Mar 7 05:38:01 EST 2012 i686 i686 i386 GNU/Linux The network speed on the VM is very slow--using the online speed tests I can only get it up to 8-9mbps. The line is 100mbps burstable and the host node has no problem achieving those speeds. If it setup a VM running CentOS, it too has no problems achieving those speeds. I've done some pretty exhaustive troubleshooting, but nothing has helped: New VM installations of Win2k8 do have the same network problem. Upgrading to most recent kernel-xen did not help (2.6.18-308.1.1.el5xen). Upgrading from xen 3.4.0 to xen 3.4.3-5 did not help. Disabling Windows firewall, etc did not help. Changing network card device config from auto negotiation to manually be 100mbps full duplex did not help. Changing the network receive buffer packet size did not help (tried all combos from 64k to 8k). At this point I'm pretty much out of ideas--any help would be appreciated!

  Read the article

• Windows Server 2008 RAID10

  - by JT

  Hello All, I am building a storage system for myself. I have a 16 bay SATA chasis and right now I have 1 x 500GB SATA for booting 8 x 1.5TB for data. 3Ware 9500S-8 RAID card where these 8 drives above are connected to. I am used to linux, but not in the RAID department. I have Windows experience too. What I am looking for is something that I can just let sit, be reliable and use for other items as well. (Like running test websites, Apache, MySQL, etc). This box is private on a Class-C subnet. My thought is to at least consider Windows Server 2008. I especially like the potential for NON-GUI Mode. Can Windows Server 2008 do a Software RAID 10 out of the box? Software RAID is better performance and better in case the raid needs to be moved to another machine? I just want to SCP files, so OpenSSH running on it? Can one install the GUI, but not use it unless they get in a bind? Is Windows a good idea or should I stick to a Linux Software RAID or FreeBSD + ZFS?

  Read the article

• How to speed up a HP M9517C

  - by Jen

  I bought a system with 8GB RAM, 1TB HD, Quad-Core AMD Phenom 9550, Nvidia Geforce 9300GE, 64-bit Windows Vista Machine. Bought it primarily because it was cheap and came with 25.5 inch screen. Problem: It's slow - if you can believe it. My Dell laptop 1525 is faster and more stable! I tried installing and dual-booting Linux Mint and ran into video and audio troubles. I need fast and stable and I'm going for awesome. Anyone have some suggestions on making this thing smoking hot? Vista is fine, but slows over time - suspect virus/spyware/etc.. But I need to use Photoshop, Fireworks, Dreamweaver, Illustrator. I've tried the alternatives and I just don't like them. When you've got deadlines looming you want to work with what you know. Also use Skype (and I had audio problems with it in Linux), gotomeeting, gotowebinar. Don't need MS Office. Tried VMWare, Virtualbox and again - I keep getting audio/video problems. I'd love someone's input on THEIR setup and how they got there. I'm sure I need to upgrade my video card, but what should I go to?

  Read the article

• LCD monitor flicker when connected to a laptop using VGA

  - by Björn Lindqvist

  I have a dual screen setup with two AOC e2450Sw monitors connected to a laptop. The laptop has one HDMI and one VGA output. When one of the monitors is connected using VGA, it flickers or displays static noise. The flickering is fairly subtle and only visible on darker colors. But it is there and noticable and appears like horizontal lines. The problem only appears on the monitor connected to the laptop using the VGA cable. If I swap the monitors, the one connected using VGA is displaying the flicker but not the one connected using HDMI. The simple solution would ofcourse be to connect both monitors using HDMI, but since the laptop only has one VGA and one HDMI out that isn't possible. I've tried tweaking the monitor setting using the OSD menu, but it had little or no effect. Update: After several more trouble shooting hours, it seems the problem is not related to the monitor or VGA cable as the problem persists even if I swap the display with another brand and different cables. So it may be the graphics card? Intel HD Graphics 4000. The laptop is Acer Aspire E1-571.

  Read the article

• Synergy on macbook with osx mavericks wifi connection

  - by user332956

  I'm trying to set up Synergy with my macbook pro running OS X 10.9.3 as a client and my Windows 7 desktop as a server. I'm having some pretty bad connection problems though when I try to use my mac. Every couple seconds the mouse or the keyboard will stop working entirely then come back. I ran some tests and found that the ping from my desktop to my mac would be very high every third ping or so(1000+ ms) or sometimes even time out. If I ping my desktop from my mac the pings are all reasonably low. I believe that this is a power saving feature of Mavericks and I have found a way to get around it by continually pinging my router on my mac, keeping my wifi card from going to sleep. I'm using this right now to type this up with synergy and have had zero issues. Has anyone else ran into this issue and found a better solution? So far, I think my best bet would be to buy an ethernet adapter but I'd rather not have yet another cable running across my desk.

  Read the article

• Do I need to be worried about these SMART drive temperatures?

  - by Steve Lorimer

  I have 5 hard drives in a machine sitting in a cupboard. /dev/sda is a 500GB Seagate drive, and is the boot disk. /dev/sd{b,c,d,e} are 2TB drives in a raid6 configuration. smartctl is showing significantly higher temperatures (like ~140 degrees celsius) on the raid drives than the boot drive. Do I need to be worried? /dev/sdb and /dev/sde are new Western Digital Black drives (new=1 week) /dev/sdc and /dev/sdd are 5 year old Hitachi drives /dev/sda [SAT], Temperature_Celsius changed from 40 to 39 /dev/sdc [SAT], Temperature_Celsius changed from 142 to 146 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 142 /dev/sdd [SAT], Temperature_Celsius changed from 142 to 146 /dev/sda [SAT], Airflow_Temperature_Cel changed from 61 to 62 /dev/sda [SAT], Temperature_Celsius changed from 39 to 38 /dev/sde [SAT], Temperature_Celsius changed from 107 to 108 /dev/sdb [SAT], Temperature_Celsius changed from 108 to 109 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 150 /dev/sdc [SAT], Temperature_Celsius changed from 146 to 150 /dev/sda [SAT], Airflow_Temperature_Cel changed from 62 to 61 /dev/sda [SAT], Temperature_Celsius changed from 38 to 39 Update: Adding detailed drive information as per request: /dev/sda =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Seagate Pipeline HD 5900.2 Device Model: ST3500312CS Serial Number: 5VV47HXA LU WWN Device Id: 5 000c50 02aad5ad6 Firmware Version: SC13 User Capacity: 500,107,862,016 bytes [500 GB] Sector Size: 512 bytes logical/physical Rotation Rate: 5900 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 1.5 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdb =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD2003FZEX-00Z4SA0 Serial Number: WD-WMC1F1398726 LU WWN Device Id: 5 0014ee 003b8bd25 Firmware Version: 01.01A01 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdc =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 Serial Number: MN1220F30WSTUD LU WWN Device Id: 5 000cca 369cc9f5d Firmware Version: MN6OA580 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sdd =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K3000 Device Model: Hitachi HDS723020BLA642 Serial Number: MN1220F30WST4D LU WWN Device Id: 5 000cca 369cc9f48 Firmware Version: MN6OA580 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Size: 512 bytes logical/physical Rotation Rate: 7200 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 4 SATA Version is: SATA 2.6, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled /dev/sde =========================== smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.9.10-100.fc17.x86_64] (local build) Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Device Model: WDC WD2003FZEX-00Z4SA0 Serial Number: WD-WMC1F1483782 LU WWN Device Id: 5 0014ee 3002d235c Firmware Version: 01.01A01 User Capacity: 2,000,398,934,016 bytes [2.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 7200 rpm Device is: Not in smartctl database [for details use: -P showall] ATA Version is: ACS-2 (minor revision not indicated) SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s) Local Time is: Tue Jun 3 10:54:11 2014 EST SMART support is: Available - device has SMART capability. SMART support is: Enabled

  Read the article

• Intermittent unavailability of an instance in a failover cluster while a standby node is offline in

  - by Emil Fridriksson

  Hi everyone. I've got a small failover cluster that I run for the websites my company has. During a RAM upgrade of the standby server, our websites started to show errors about not being able to access the database server. I verified that the instance was indeed up and the server accessable via remote desktop. I also tried a SQL connection to it and it worked, but that might have been after it became available again. This happened on and off until we were able to roll back the hardware changes that were in progress on the standby server and we were able to bring it back up. There was nothing of interest in the SQL Server log, but there is a continous log for the whole duration of the problem, so there was no restart of the SQL Server service. The event viewer is of more interest, since it shows events relating to the heartbeat network card, but I don't know how that would affect the availability of the server, since the standby node is offline. I'd appreciate any help you can provide, it's not very redundant if the setup depends on the standby server being up. :) Here are the event logs from the time of the problem, I include all of them since I can't seem to see what could possibly be the cause of the problem. Event log: http://hlekkir.com:800/htmltable.htm

  Read the article

• Packet drop measured by ethtool, tcpdump and ifconfig

  - by Rayne

  Hi all, I have a question regarding packet drops. I am running a test to determine when packet drops occur. I'm using a Spirent TestCenter through a switch (necessary to aggregate Ethernet traffic from 5 ports to one optical link) to a server using a Myricom card. While running my test, if the input rate is below a certain value, ethtool does not report any drop (except dropped_multicast_filtered which is incrementing at a very slow rate). However, tcpdump reports X number of packets "dropped by kernel". Then if I increase the input rate, ethtool reports drops but "ifconfig eth2" does not. In fact, ifconfig doesn't seem to report any packet drops at all. Do they all measure packet drops at different "levels", i.e. ethtool at the NIC level, tcpdump at the kernel level etc? And am I right to say that in the journey of an incoming packet, the NIC level is the "so-called" first level, then the kernel, then the user application? So any packet drop is likely to happen first at the NIC, then the kernel, then the user application? So if there is no packet drop at the NIC, but packet drop at the kernel, then the bottleneck is not at the NIC? Thank you. Regards, Rayne

  Read the article

• Determine the time difference between two linux servers

  - by Paul

  I am troubleshooting a latency network issue on a network. It is probably a nic or cabling issue, but while I was going through the process of figuring it out, I was looking at the timings of a ping packet leaving a network card and arriving at another server. Both linux. So I have tcpdump running on both, and I issue a ping from one to the other, and back again, and looking at the timing differences might have shed light on where the latency is coming from. It is an academic exercise now, as I need to eliminate some more fundamental causes, but I was curious as to how this could be achieved. Given that ntpd is installed and running on two servers, how can I confirm the current time discrepency between the two servers, to whatever level of accuracy is possible - given that we are talking about latency on a local lan, which is ideally a millisecond or so. NTP itself is accurate to a couple of ms under good conditions, and as both servers are in the same environment, they should (presumably) achieve a similar level of accuracy, and so should have a time discrepency between them of a only few ms - but how can I check this?

  Read the article

• Ati X1600 driver problem on Mac

  - by Mulot

  Hi all, I currently own a 06' Macbook pro 1.1, and since some months I have recurrent problems of displays bug or artifacts. I searched quickly around to see that a lot of other users on Mac (iMac or Macbook pro) also have the same problem due to a problem for the X1600 video card. Apparently it's due to overheating problem, in my case even without warming a lot I have very bad display bugs such as colorful pixel lines, or glitches, and freeze and crash, all of this on Tiger, Leopard and Snow Leopard. I found this interesting article here talking about this problem and trying to gather people so that Apple take the serious GPU problem in consideration. In one of the comments, an user said he removed all bundle named with "radeon" and then he had no more problems under Leopard, and seems ot work fine well too on Snow Leopard. I did the same thing, I removed the bundles of the driver, restart, and no more problems, but not more 3D acceleration, which is not an acceptable solution. For those interested, here is the list of files to be deleted to stop having this problem. /System/Library/Extensions/ATIRadeonX1000.kext /System/Library/Extensions/ATIRadeonX1000GA.plugin /System/Library/Extensions/ATIRadeonX1000GLDriver.bundle /System/Library/Extensions/ATIRadeonX1000VADriver.bundle /System/Library/Extensions/ATIRadeonX2000.kext /System/Library/Extensions/ATIRadeonX2000GA.plugin /System/Library/Extensions/ATIRadeonX2000GLDriver.bundle /System/Library/Extensions/ATIRadeonX2000VADriver.bundle I would like to know if there is a way to fix this using other drivers if that's possible or by creating a group to force Apple to make a replacement program in place. Edit : How to locate those files on your hard drive if you are not under Snow Tiger : sudo find / -iname "*radeon*"

  Read the article

• Windows Vista: Screen remains darkened for 30-60 seconds *after* UAC prompt

  - by sf2k

  Fixing someone's Vista computer. Process: I click any program or process that opens a User Account Control prompt. Screen goes dim so you may hit Continue to perform a secure user action. I click Continue Screen goes black for 30 seconds to 1 minute while you wait for the screen to return. In another example I click Cancel and screen still then goes black for 30 seconds to a minute. In that timeframe a chime goes off while you wait. (No chime if it was being cancelled.) Then screen comes back to continue with whatever. Something is occurring after the UAC prompt. Considering everything is practically a UAC acceptance this can get pretty annoying pretty quickly. Laptop has external monitor to regular external plug. Works fine. Laptop also has USB IOGEAR additional external video card. This is problematic but when unplugged same above behaviour occurs. I've ruled out monitor interference since same blackout after the UAC prompt appears with external monitors plugged in or when rebooted with no external monitors. Any suggestions on how to address this problem?

  Read the article

• S5000XVN Intel Motherboard - Only sees 12 out of 16GB of RAM

  - by Richie086

  So I have an older Intel S5000XVN motherboard, here are the specs CPU Arch : 2 CPU - 2 Cores - 2 Threads CPU PSN : Intel Xeon CPU 5160 @ 3.00GHz CPU EXT : MMX, SSE (1, 2, 3, 3S), EM64T, VT-x CPUID : 6.F.6 / Extended : 6.F CPU Cache : L1 : 2 x 32 / 2 x 32 KB - L2 : 4096 KB Core : Woodcrest (65 nm) / Stepping : B2 Freq : 2985.21 MHz (331.69 * 9) MB Brand : Intel MB Model : S5000XVN NB : Intel 5000X rev 31 SB : Intel 6321ESB rev 09 RAM : 16384 MB FB-DDR2 RAM Speed : 331.7 MHz (1:1) @ N/A Slot 1 : 2048MB (5300) Slot 1 Manufacturer : Kingston Slot 2 : 2048MB (5300) Slot 2 Manufacturer : Qimonda Slot 3 : 2048MB (5300) Slot 3 Manufacturer : Kingston Slot 4 : 2048MB (5300) Slot 4 Manufacturer : Qimonda Slot 5 : 2048MB (5300) Slot 5 Manufacturer : Kingston Slot 6 : 2048MB (5300) Slot 6 Manufacturer : Qimonda As you can clearly see, CPU-Z says I have 16GB of PC2-5300 RAM installed. For some reason in both BIOS and in Windows the maximum usable RAM is 12GB instead of 16GB. I have a dedicated video card connnected, so it can't be stealing RAM to use for the GPU (the S5000XVN does not have any onboard video). I am running Windows Server 2008 R2 x64 as the primary OS - so there should not be a memory limitation imposed on me from the OS. Has anyone experienced this before? Any ideas on how I can actually use all 16GB of RAM? I plan on using this machine to use for a Hyper-V server and have x2 Quad Core Xeon CPUs on the way as I write this post.

  Read the article

• How do I troubleshoot a slow hard drive?

  - by Bruce Connor

  My computer is suffering of slow-downs and I'm not surprised (it's around 6 years old). Here's what I've verified: They are not very frequent (only a couple of times a day). When they happen a single application will hang for 10-60 seconds, while the rest don't hang but also get slow. Even as it is happening, the CPU usage stays low. It happens to applications (such as text editor, firefox, skype). It never happens to some applications (such as games) which I use for hours under heavy CPU load. Also of note: The Graphics card and PSU are new (around a year). Though I have a decent amount of software installed right now, this was happening even right after I reinstalled Windows. This HDD has been through many partinioning schemes, and a few heavy operations (such as moving around 200GB of data). Because of the above, I am already 70% sure the problem is with the hard drive. Before I replace it, however, I want to rule out other less likely possibilities (such as RAM, software, or PSU). I don't have the money to replace the entire box right now, but I can easily replace one of the components. I've read several questions (such as this one) which give general guidance on troubleshooting an unknown issue, that is not what I'm looking for here. My main question is: What tests or benchmarks can I run to verify I have a problematic hard drive? I don't need to solve this problem, I am content with just making sure it's the hard drive. I could borrow a newer hard drive from a friend and see if it gets better. A positive result would rule out all other components, but it wouldn't rule out a software issue (since this new hard drive won't have any of the software I use daily). Running on Windows/Linux.

  Read the article

• How to connect through a proxy using Remote Desktop?

  - by scottmarlowe

  So I've got a home server running Windows Server 2003. I use a dual network card setup and Routing and Remote Access to link the internal, private network to the external connection. The external connection hooks directly to my cable modem (so no routers or other devices sitting between). The problem I'm having is that I can't connect remotely from a location outside the house (so connecting to the server's external connection) to the server using either Remote Desktop or VNC. I have enabled both ports in Routing and Remote Access's firewall to allow access, and I have enabled Remote Desktop in Windows Server 2003. The odd thing is that I can access my home server's SVN repository and I can even ping the server's IP. I am using the IP to attempt to connect, though I use a dyndns.com provided name to connect to my SVN repository, so it shouldn't make a difference (I know the IP is getting resolved correctly). Any ideas on where to start diagnosing this one? I haven't seen anything in my server's event log. If any other info is needed, let me know. Thanks. UPDATE: One last piece of information: We use a proxy server at work, which I'm nearly 100% sure is the culprit. I have a workaround--if I connect to our VPN (even though I'm already inside the building) I am able to connect to my home server. This is with VNC. However, is there a way to connect through a proxy using Remote Desktop? ONE MORE UPDATE: Indeed, it was the http proxy I'm sitting behind at work that was causing the issue. An acceptable workaround is to use my VPN connection to bypass the proxy, and I'm in!

  Read the article

• Flash alternative for iBook Mac?

  - by Hunter Dolan

  I have a old Apple iBook G4 that I decided to hook up to my main TV. I like the setup because I can surf the internet on my TV now. The only thing that I can't seem to do is watch Flash videos. Apparently Flash Player 10 doesn't play nice with the iBook's graphics card's GPU, leaving all the graphics processing to the CPU which is a disaster. Others suggested downgrading to Flash Player 9, I did that, and youtube worked fine, but Hulu (The main reason I wanted to hook it up to the TV in the first place) did not. Anyone know of a Flash alternative or a Flash 10 fix for the iBook? Or even a Hulu client that doesn't require Flash. Here are my iBook's Specs Model Name: iBook G4 <br> Model Identifier: PowerBook6,5 <br> Processor Name: PowerPC G4 (1.2) <br> Processor Speed: 1.2 GHz <br> Number Of CPUs: 1 <br> L2 Cache (per CPU): 512 KB <br> Memory: 512 MB <br> Bus Speed: 133 MHz <br> Boot ROM Version: 4.8.7f1 <br> Mac OS X Version: 10.5.8 <br> PS: Don't tell me that I need to buy a new computer. I know that I would have better results with a new computer but I don't want to buy a new computer just for Hulu.

  Read the article

• How to eliminate overscan on Ubuntu HTPC

  - by Norman Ramsey

  I'm using an Ubuntu box with Nvidia graphics card as an HTPC. My HDTV is a Sony Bravia KDS-R50XBR1; this is a rear-projection unit with many inputs. I am using the HDMI input. I'm using the proprietary Nvidia drivers and they recognize the 1080x1920 resolution just fine. The display is a little fuzzy but at 50 inches it's perfect for movies. My problem is that the TV has three overscan settings, and none of them reduces overscan to zero. When I was using dual-screen this was fine, but I'm moving to where the TV is my only screen, and the Gnome panels are not visible because of the overscan. I'd like to figure out how to eliminate the overscan, without trying to scale my 1080p content down to 920p or something ridiculous like that. Ideally there would be some scurvy trick, perhaps involving the TV service menu, to get rid of the overscan on the TV side. Or I could move the Gnome panels, but I still would be missing the edges of my movies. Suggestions most welcome.

  Read the article

• Intel DriverInstall issue on HP ProLiant server DL580G5

  - by TomTom

  Given: A HP ProLiant server to be used for Hyper-V server (R 2) Problem: The server has a HP NC364T quad port card, which actually is an Intel 1000 Pro adapter. We are stuck getting this adapter properly working. We need to get it working with: 2 trunks of 2 ports each one of them fully vlan "aware" (without filtering anything - so that Hyper-V can do the VLAN filtering). So far we did: Install the server Install latest PSP. Problem here - tool does not work to set up teaming. We tried to install the latest ProWin pack from Intel - the drivers there are a LOT more current (26th of Marrch 2010, 9.13.41.0). The intalled driver (Microsoft) is ancient (march 2009, 9.13.4.10) A driver update fails both on command line (pnputil) as well as the PortLock device manager executable. No informatoin is provided. the ANS toolset can not create teams (fails with error - again, no reason provided), I know of no logs and the event log has no information either. Questions: What are the best drivers to use? How do we actually install them? How can we then set up teaming and how do we set up the VLAN behavior wanted?

  Read the article

• Laptop recommendation - Portable Gaming

  - by ivan

  So, I'm looking for a new laptop (http://superuser.com/questions/116869/toshiba-satellite-u500-totally-damaged-lcd). My requirements for a new Laptop are: -good keyboard(illuminated) and touchpad (multi-media keys included, should be better than toshiba u500) -good graphics card, with system rating of 6.3 and up for gaming graphics (my Toshiba U500 has 6.3). I used to run some heavy games on my Toshiba U500 with ATI Mobility Radeon 4570 with 512 mb VRAM but the framerates are not that nice on high settings. -Decent CPU but I think all new Core i3, i5, i7 can run most of recent resource intensive games (My Toshiba U500 has a Core 2 Duo T6500, 2.13 Ghz) I'm also looking for a long-term reliability, good sound quality, lots of fast RAM of-course(4GB DDR3 - 1066Mhz and up) and a clear looking LED screen with a decent resolution. (I can accomodate a laptop with screen size of 13-inch upto 15.6 inch, and I don't want it to be heavy because I might be taking it outdoors) I'm actually impressed when I saw HP Pavilion DV6t but the screen resolution seems to be a little too small for 15.6 inch. The Pavilion DV3 are also good but I want to know if there other options. Looking for some opinions.. Thanks. :D

  Read the article

• Graphics and USB devices freezing soon after OS loads

  - by Andrew

  I run Ubuntu/Windows dual boot. Last night I started the upgrade to Ubuntu 12.04, and my computer has not worked since in either Windows or Ubuntu. Here's what I got when I rebooted after the upgrade, and continue to get every time I boot: Gets to GRUB screen OK. Choose Ubuntu - black screen or crazy purple lines. At first I assumed something went wrong with the upgrade (often happens). Choose Windows - works fine, I log in, but soon after that the graphics freeze (sometimes with purple artifacts). The keyboard and mouse (both USB) also lose power at the same instant, and none of the USB ports have power to them. This happens sooner or later every time I boot. Update: the HDD also appears to lose power at the same point. I have tried a live CD, but my computer refuses to boot any CD even after disabling all other boot options in the BIOS. I have disconnected everything except keyboard, mouse, graphics card with one monitor, one RAM sick and HDD; no change. I also took the little battery out to reset CMOS. I am pretty sure no matter how wrong the Ubuntu upgrade went, it wouldn't cause the above symptoms in Windows. So the only explanation I can think of is that a hardware failure occurred at the same time. Some possible causes of this I can think of are: A couple of days before this, I added a third screen (which worked fine). About a week before, my house lost power in a storm (no ill effects over the past few days though). What can I do, other than buy a new motherboard/CPU and hope it works? Unfortunately I don't have another box to swap parts into to test at the moment.

  Read the article

• simple network between xp & 7 with cross cable problem...

  - by LostLord

  hi my dear friends : i have a simple network between xp & 7 windowses with cross cable (2 pc home)... ===================================================================== the one with 7 is mother and have 2 lan device (onboard + pci) A. onboard is like this when u go to tcp/ip v4 properties:(4 adsl internet) obtain an ip... preferred dns server : 81.91.129.67 alternate dns server : 4.2.2.4 shared...no permission 4 change so every thing is ok for internet on windows 7. B. the other lan pci card that is connected to pc with xp is like this : 192.168.2.11 255.255.255.0 0.0.0.0 empty empry computer name : cougar workgroup : nethome homeNetwork is disabled (i think that is 4 2 pc's with 7 os not xp) every thing is off in network options except file & printer sharing in public area ===================================================================== pc with xp os is like this : 192.168.2.12 255.255.255.0 192.168.2.11 (mean gateway) 4.2.2.4 8.8.8.8 computer name : tiger workgroup : nethome ===================================================================== at last my little net is ok... mean both have internet , both can see each other by their ip (\\192.168.2.11 or \\192.168.2.12) my problem is when in pc with xp type \\cougar it shows an error about network path! but in pc with 7 \\tiger works perfec. what is the problem in system with xp ? in few days ago this network was ok (search by computer name) when both os were xp , so there is no problem with my cable or devices. another problem is i can not find tiger in my network list in 7 pc \ why? is something wrong with my network? thanks 4 future advance best regards

  Read the article

• USB mouse disconnecting and reconnecting in windows and linux

  - by Kalak

  I have a problem similar to what is described at "Why is my USB mouse disconnecting and reconnecting randomly and often?" except is is happening in both Windows 7 and Linux (Ubuntu 12/04TLS, fully patched), multiple mice, multiple OSs. It stops responding to input for about 3-5 seconds, then starts responding again. It's more frequent and lasts longer when running games (TF2, L4D, Dishonored, Borderlands 2, and more), but happens when just running the OS as well. I was hoping it was the motherboard so I bought a USB 2.0 PCI card to try that, but it's still happening. I've stripped it down to just the keyboard and mouse (different keyboard too just in case the keyboard was the problem), but it's still happening. All the hardware (mice and keyboards) work fine on other computers. I have literally pulled the mouse and keyboard out and plugged them into another computer (laptop) and re-joined the online game and had no problem with the keyboard and mouse combo that just failed on my gaming rig. Please no driver / Windows or Linux only suggestions, as that wouldn't effect both OSs. edit: known good mice I've brought home are now going bad. I suspect the hardware is messed up (voltage?) and has been frying the mice.

  Read the article

• Can't get an IBM xSeries 345 server to load Windows Server 2003 using ServerGuide utility

  - by Kyle Noland

  I have a client that has an IBM xSeries 345 eServer. Per the IBM support website, I have downloaded the ServerGuide Setup 7.4.17 installation ISO and burned a bootable CD. The CD boots fine and loads the utility. I walk through the following screens without any issue: Set the date and Time Detect the IBM ServeRAID card and install the latest firmware Clear the hard disks Set up the RAID array The next step is format the NOS partition. I select my partition size and the utility goes through the following steps: Creating NOS partition Formatting NOS partition (NTFS) Copying W32 files The copying W32 files takes about 10 minutes. I see the CD drive and disks working hard. When the copying is complete, I'm taken to a blank page just NOS Partitioning at the top. At the bottom of the screen are the familiar Back and Exit buttons. I see the place where the Next button should be, and if I click on it I can tell there is something there, but the space is empty. No button is displayed and clicking the empty spot doesn't ever take me to the next screen. I can't load the OS until I get past this part. I have already tried: Burning multiple copies and versions of the ServerGuide CD Letting the final screen just sit there over the weekend thinking it might advance after syncing the drives or something Has anybody else seen this? I'm really at a loss here.

  Read the article

• Ubuntu 12.04 froze during update, won't boot

  - by Cichol

  I've recently installed Ubuntu 12.04 on my laptop, and every time i tried to update it, it would freeze for a few seconds, and tell me that the updates could not be downloaded. After many, many tries I managed to get them downloaded, but then in the middle of installing them, it froze. Completely. No mouse movement, no blinking lights, no nothing. After a few hours of letting it sit there, I finally hit the power button to do a hard reset, and now when I select Ubuntu on the boot screen (Dual-boot with Windows 7), I get a blank purple screen, and then nothing. Another freeze. I've tried getting into the console, but no command I input has any visible effect. I have a ton of music stored on the partition it's in, so I'd really rather not have to reinstall. My specs, to the best of my knowledge: Clevo Corp model B7130 (Sager custom) CPU: Intel Core i5 @ 2.53gHz (4 CPUs) Graphics Card: Nvidia GeForce 425m 4096 MB RAM Drivers: Whatever comes with the download of 12.04. As a side-note, I installed Ubuntu via the Windows Installer program (wubi). Does that make a difference?

  Read the article

• Mac Security - Which one?

  - by Bob Rivers

  Hi, Recently I had my credit card cloned. A few hours after shopping at an online store (in which I trust and buy since 2006) I received a call from my bank asking if I recognize a $5,000 debt to a store(?!) called Church of Christ... I'm a Mac user (OS X 10.6.3). I always kept my system updated and I have firewall enabled (in my Mac and in my broadband router), but I decided to adopt some kind of protection. I don't want to rise passionate discussions. Real or not, snake oil or not, I need to have back my peace of mind... I read this and this posts. I selected two software that I think that could help me (both have more features other than just an antivirus). Does someone have feedback about Intego's VirusBarrier X6 or Trendmicro's Smart Surfing? Intego solutions seems to be better, but TrendMicro brand/name is stronger in corporate environment, so their solution should be good. Both solutions have 30 day free trial, but I would like to hear something from you. Any other solution that I should look? TIA, Bob

  Read the article

< Previous Page | 235 236 237 238 239 240 241 242 243 244 245 246  | Next Page >