Search Results

Search found 21678 results on 868 pages for 'network traffic'.

Page 239/868 | < Previous Page | 235 236 237 238 239 240 241 242 243 244 245 246  | Next Page >

• No wireless connection using a conceptronic c54i (RT2561/RT61 rev B)

  - by jrosell

  Detected but not working. New install on ubuntu 11.10 using coneptronic C54Ri. As documentation says it uses Ralink drivers.... Any ideas why my wireless does not work? $ lspci -nn | grep -i 'ralink' 01:05.0 Network controller: Ralink corp. RT2561/RT61 rev B 802.11g ifconfig eth0 Link encap:Ethernet HWaddr 00:1e:90:e5:af:13 inet addr:192.168.0.197 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::21e:90ff:fee5:af13/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:28361 errors:0 dropped:0 overruns:0 frame:0 TX packets:16858 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:39812172 (39.8 MB) TX bytes:1633405 (1.6 MB) Interrupt:43 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6608 (6.6 KB) TX bytes:6608 (6.6 KB) iwconfig wlan0 wlan0 IEEE 802.11abg ESSIDff/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thrff Fragment thrff Power Managementff lsmod | grep rt rt61pci 27493 0 crc_itu_t 12627 1 rt61pci rt2x00pci 14202 1 rt61pci rt2x00lib 48114 2 rt61pci,rt2x00pci mac80211 272785 2 rt2x00pci,rt2x00lib cfg80211 172392 2 rt2x00lib,mac80211 eeprom_93cx6 12653 1 rt61pci parport_pc 32114 1 parport 40930 3 ppdev,parport_pc,lp lsmod | grep rt [ 2497.816989] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.827112] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.837430] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847528] phy0 -> rt2x00pci_regbusy_read: Error - Indirect register access failed: offset=0x0000308c, value=0xffffffff [ 2497.847632] phy0 -> rt61pci_wait_bbp_ready: Error - BBP register access faile d, aborting. [ 2497.847637] phy0 -> rt61pci_set_device_state: Error - Device failed to enter state 4 (-5). sudo lshw -C network *-network DISABLED description: Wireless interface product: RT2561/RT61 rev B 802.11g vendor: Ralink corp. physical id: 5 bus info: pci@0000:01:05.0 logical name: wlan0 version: 00 serial: fa:b8:14:58:62:35 width: 32 bits clock: 33MHz capabilities: pm cap_list ethernet physical wireless configuration: broadcast=yes driver=rt61pci driverversion=3.0.0-12-generic firmware=0.8 latency=0 link=no multicast=yes wireless=IEEE 802.11abg resources: irq:16 memory:fdef8000-fdefffff iwlist scan lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan0 Failed to read scan data : Network is down uname -mr 3.0.0-12-generic i686 Edit 1 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no On reboot, sudo lshw -C network returns network is ok. Hovever, WPA keeps on asking the wireless key

  Read the article

• Hyper-V Manager version 6.2, an experience in virtual switch setup

  - by Kevin Shyr

  The version number of Hyper-V manager is 6.2.9200.16384   This is what came with my Windows 8 work laptop (by enabling Windows features) The blogs I read indicated that I need an external switch for my guest OS to access internet, and an internal one for them to share folder with my Host OS.  I proceeded to create an external virtual switch, and here is the screenshot. After setting up the network adapters on the guest OS, I peeked into host OS networking, and saw that Network Bridge was already created.  GREAT!  So I fired up my guest OS and darn, no internet.  Then I noticed that my host internet was gone, too.  I looked further and found that even though I have a network bridge, no connection has the status "Bridged"Once I removed the bridge (by removing individual connection from the bridge, I know, weird, since none of them say "Bridged" in status)  I re-selected the connection that I want and add them to the bridge to create a new network bridge.  Once my wireless connection status shows "Bridged", I was able to get to internet from my guest OS.Two things I noticed after I got internet for everyone ( my host and guest OS):My network adapters in the host OS no longer shows "Bridged", but everyone can still get to the internetThe virtual switch that I set up for "External" is now showing to be "Internal", and I was able to create shared folder between host and guest OS.  This means I didn't have to create the other "Internal" virtual switch.

  Read the article

• change browser to open weblinks in thunderbird

  - by Bevor

  Hello, because it's almost obvious that either Thunderbird or Firefox freeze my whole system after some time, I'd like to not use FF at the moment and let Thunderbird run only for a short time as long as I check e-mails. Thunderbird web links should be opened with opera from now. For that I went in Thunderbird to Preferences-Advanced-General-Config Editor and set the following: network.protocol-handler.app.http -> /usr/bin/opera network.protocol-handler.app.https -> /usr/bin/opera network.protocol-handler.warn-external.ftp -> true network.protocol-handler.warn-external.http -> true network.protocol-handler.warn-external.https -> true Moreover I changed in Gnome in System-Preferences-Prefered Applications Opera as webbrowser and I checked in FF that it should warn if FF is not the default browser (obviously it isn't anymore). Unfortunately all of these settings doesn't work. Thunderbird still opens web links with FF. Any explantions why? (I already restarted Thunderbird although I don't have to, but no effect)

  Read the article

• Uploading or attaching files that located on a shared drive doesn't work?

  - by Alex

  I have this odd, quite minor, but annoying issue that I am quite perplexed about. Whenever I try to upload a file via my browser(let's say attach a file to an email in GMail), I click 'Browse' button and it opens standard file selection dialog, that doesn't show network drives. Further more if I try to drag a file from a network drive into GMail, it doesn't work either, it just doesn't let me do that. This issue has been around for quite sometime now, and I am just curious if this is something on my side or if it's a bug or a misconfiguration of some sort. FWIW, I am currently running 10.10, network drive is a samba share on NAS. This happens in FF and Chrome and this is only happens with Samba mounts. As a matter of fact, NFS volumes that are located on the same network operate perfectly fine.

  Read the article

• NMap 6.01

  - by TATWORTH

  NMap 6.01 has been released at http://nmap.org/download.html"Nmap ("Network Mapper") is a free and open source (license) utility for network discovery and security auditing. Many systems and network administrators also find it useful for tasks such as network inventory, managing service upgrade schedules, and monitoring host or service uptime. Nmap uses raw IP packets in novel ways to determine what hosts are available on the network, what services (application name and version) those hosts are offering, what operating systems (and OS versions) they are running, what type of packet filters/firewalls are in use, and dozens of other characteristics. It was designed to rapidly scan large networks, but works fine against single hosts. Nmap runs on all major computer operating systems, and official binary packages are available for Linux, Windows, and Mac OS X. In addition to the classic command-line Nmap executable, the Nmap suite includes an advanced GUI and results viewer (Zenmap), a flexible data transfer, redirection, and debugging tool (Ncat), a utility for comparing scan results (Ndiff), and a packet generation and response analysis tool (Nping)."Home page is at http://nmap.org/  Nmap is free to download and use. You can download the source and compile it yourself if you so require.

  Read the article

• How to restart WiFi interface without rebooting (it drops connection)?

  - by Dima

  I boot into ubuntu and it connects to the Wifi network fine. After about 10-15min the DNS stop resolving any website and a couple of minutes later network-managers tells me that I'm disconnected and tries to reconnect constantly to my router and fails to do it. Upon Ubuntu restart everything works fine for the first 10-15min again. When I boot into Mac OS X everything is fine with the same connection! How do I restart wifi interface? sudo ifdow wlan0 just tells me that wlan0 is not configured and wlan0 doesn't appear in /etc/network/interfaces either, which I find strange.... (unless network-manager is doing it behind my back).

  Read the article

• Windows Not Sleeping All Night

  - by John Paul Cook

  Having a computer wake up when you don’t want it to wastes electricity and drains the battery on mobile devices. My desktop had been waking up at night, so I assumed it was some network traffic on my home network. I unchecked Allow this device to wake the computer on my network adapters . Figure 1. Network adapter Power Management tab. That didn’t solve the problem. I included the screen capture in Figure 1 because it could be part of the solution for someone else. To identify the root cause instead...(read more)

  Read the article

• 4 Key Ingredients for the Cloud

  - by Kellsey Ruppel

  It's a short week here with the US Thanksgiving Holiday. So, before we put on our stretch pants and get ready to belly up to the dinner table for turkey, stuffing and mashed potatoes, let's spend a little time this week talking about the Cloud (kind of like the feathery whipped goodness that tops the infamous Thanksgiving pumpkin pie!) But before we dive into the Cloud, let's do a side by side comparison of the key ingredients for each. Cloud Whipped Cream  Application Integration  1 cup heavy cream  Security  1/4 cup sugar  Virtual I/O  1 teaspoon vanilla  Storage  Chilled Bowl It’s no secret that millions of people are connected to the Internet. And it also probably doesn’t come as a surprise that a lot of those people are connected on social networking sites.  Social networks have become an excellent platform for sharing and communication that reflects real world relationships and they play a major part in the everyday lives of many people. Facebook, Twitter, Pinterest, LinkedIn, Google+ and hundreds of others have transformed the way we interact and communicate with one another.Social networks are becoming more than just an online gathering of friends. They are becoming a destination for ideation, e-commerce, and marketing. But it doesn’t just stop there. Some organizations are utilizing social networks internally, integrated with their business applications and processes and the possibility of social media and cloud integration is compelling. Forrester alone estimates enterprise cloud computing to grow to over $240 billion by 2020. It’s hard to find any current IT project today that is NOT considering cloud-based deployments. Security and quality of service concerns are no longer at the forefront; rather, it’s about focusing on the right mix of capabilities for the business. Cloud vs. On-Premise? Policies & governance models? Social in the cloud? Cloud’s increasing sophistication, security in applications, mobility, transaction processing and social capabilities make it an attractive way to manage information. And Oracle offers all of this through the Oracle Cloud and Oracle Social Network. Oracle Social Network is a secure private network that provides a broad range of social tools designed to capture and preserve information flowing between people, enterprise applications, and business processes. By connecting you with your most critical applications, Oracle Social Network provides contextual, real-time communication within and across enterprises. With Oracle Social Network, you and your teams have the tools you need to collaborate quickly and efficiently, while leveraging the organization’s collective expertise to make informed decisions and drive business forward. Oracle Social Network is available as part of a portfolio of application and platform services within the Oracle Cloud. Oracle Cloud offers self-service business applications delivered on an integrated development and deployment platform with tools to rapidly extend and create new services. Oracle Social Network is pre-integrated with the Fusion CRM Cloud Service and the Fusion HCM Cloud Service within the Oracle Cloud. If you are looking for something to watch as you veg on the couch in a post-turkey dinner hangover, you might consider watching these how-to videos! And yes, it is perfectly ok to have that 2nd piece of pie

  Read the article

• Broadcom 4313 Signal strength very low on an HP Pavilion dv4

  - by thegreyspot

  I have a HP pavilion dv4 4141US laptop running fresh ubuntu 11.10. This laptop has a broadcom 4313gn chipset for the network card. The network card is using the brcmsmac driver. Which, I heard else where on askUbuntu that its the best driver to be using for this card. I can connect to my network, however I have extremely low network signal. Right now I am right in front of the router, and I only get 72%. If i go to the room directly behind the router's wall, i get no signal, where as with windows 7 I get a nice 70% percent. UPDATE: I use WEP at home and an open wireless connection at work. Both have same result. Both are completely different routers. Also you G What can i do?

  Read the article

• How to connect to the internet via command line or graphical utility given I can't click at the top of the screen?

  - by Ben

  My Ubuntu 12.04 installation has an input problem resulting preventing me from clicking near the top of the screen. That is, there is an unclickable area, circa 60 pixels high and stretching all the way across the screen. I will ask about this in a later question. For now, I would just like to be able to connect to the internet, given this limitation. I am able to access the network connections application by hitting the super key and typing "network connections". There is a LAN and a wireless network available. The network icon in the bar at the top of the screen shows an empty wedge, which I suppose means that wireless is off. I've attached the cable for the Ethernet connection, but it does not seem to have connected automatically. How can I figure out what's going on? (I'll happily edit in the output of any relevant terminal commands.) Thank you.

  Read the article

• ZoneAlarm Internet Security Suite

  Five interlocking security services for the ultimate in network protection

  Read the article

• wlan0 (WPA2) doesn't work when configured manually

  - by 71GA

  I have been trying to reconfigure my eth0 and wlan0 interfaces by editing /etc/network/interfaces file as folows: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.1.11 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 dns-nameservers 193.2.1.66 auto wlan0 iface wlan0 inet static address 192.168.1.10 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 dns-nameservers 193.2.1.66 wpa-driver wext wpa-ssid lausi wpa-ap-scan 2 wpa-proto RSN wpa-pairwise CCMP wpa-group CCMP wpa-key-mgmt WPA-PSK wpa-psk 8952a447c860d13847ba1cabd15314ba9caf2fb207f19598f90c43fcd43c0d97 But my wireless doesnt work when i use command /etc/init.d/networking restart and when i do this i get an error: * Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces * Reconfiguring network interfaces... RTNETLINK answers: File exists Failed to bring up eth0. ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument RTNETLINK answers: File exists Failed to bring up wlan0. Although it clearly states that my eth0 interface couldn't be brought to life it is working! But i cant say this for the wlan0 interface which doesn't even work if i unplug internet cable and again use command /etc/init.d/networking restart. This seems weird to me... When i use ìfconfig -a command i get an output which confirms that wlan0 isnt working and eth0 is. ziga@ziga-cq56:/etc/network$ ifconfig -a eth0 Link encap:Ethernet HWaddr 60:eb:69:6f:5f:69 inet addr:192.168.1.11 Bcast:192.168.1.13 Mask:255.255.255.0 inet6 addr: fe80::62eb:69ff:fe6f:5f69/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6764 errors:0 dropped:0 overruns:0 frame:0 TX packets:6641 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5932190 (5.9 MB) TX bytes:1331846 (1.3 MB) Interrupt:42 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1759 errors:0 dropped:0 overruns:0 frame:0 TX packets:1759 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:107772 (107.7 KB) TX bytes:107772 (107.7 KB) wlan0 Link encap:Ethernet HWaddr 70:f3:95:e7:57:cc inet addr:192.168.1.10 Bcast:192.168.1.12 Mask:255.255.255.0 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) How can i make my wlan0 interface work? It had been working previously with network manager and wicd...

  Read the article

• NetSetMan

  A handy freeware tool for helping you efficiently view and manage all your network settings

  Read the article

• Write application indicator with no icon

  - by danjjl

  I wrote an application indicator that displays information about my monthly network consumption. I do not want it to have an icon next to the text I display. How do I write an application indicator without an icon? The code I use to initialize my indicator is: self.indicator = appindicator.Indicator.new("VooMeter", "network", appindicator.IndicatorCategory.SYSTEM_SERVICES) Reading the documentation I can not find the value to put instead of "network"

  Read the article

• Using Content Analytics for More Effective Engagement

  - by Kellsey Ruppel

  Using Content Analytics for More Effective Engagement: Turning High-Volume Content into Templates for Success By Mitchell Palski, Oracle WebCenter Sales Consultant Many organizations use Oracle WebCenter Portal to develop these basic types of portals: Intranet portals used for collaboration, employee self-service, and company communication Extranet portals used by customers and partners for self-service and support Team collaboration portals that allow users to share documents and content, track activity, and engage in discussions Portals are intended to provide a personalized, single point of interaction with web-based applications and information. The user experiences that a Portal is capable of displaying should be relevant to an individual user or class of users (a group or role). The components of a Portal that would vary based on a user’s identity include: Web content such as images, news articles, and on-screen instruction Social tools such as threaded discussions, polls/surveys, and blogs Document management tools to upload, download, and edit files Web applications that present data visualizations and data entry modules These collections of content, tools, and applications make up valuable workspaces. The challenge that a development team may have is defining which combinations are the most effective for its users. No one wants to create and manage a workspace that goes un-used or (even worse) that is used but is ineffective. Oracle WebCenter Portal provides you with the capabilities to not only rapidly develop variations of portals, but also identify which portals are the most effective and should be re-used throughout an enterprise. Capturing Portal AnalyticsOracle WebCenter Portal provides an analytics service that allows administrators and business users to track and analyze portal usage. These analytics are captured in the form of: Usage tracking metrics Behavior tracking User Profile Correlation The out-of-the-box task reports that come with Oracle WebCenter Portal include: WebCenter Portal Traffic Page Traffic Login Metrics Portlet Traffic Portlet Response Time Portlet Instance Traffic Portlet Instance Response Time Search Metrics Document Metrics Wiki Metrics Blog Metrics Discussion Metrics Portal Traffic Portal Response Time By determining the usage and behavior tracking metrics that are associated with specific user profiles (including groups and roles), your administrators will be able to identify the components of your solution that are the most valuable.  Your first step as an administrator should be to identify the specific pages and/or components are used the most frequently. Next, determine the user(s) or user-group(s) that are accessing those high-use elements of a portal. It is also important to determine patterns in high-usage and see if they correlate to a specific schedule. One of the goals of any development team (especially those that are following Agile methodologies) should be to develop reusable web components to minimize redundant development. Oracle WebCenter Portal provides you the tools to capture the successful workspaces that have already been developed and identified so that they can be reused for similar user demographics. Re-using Successful PortalsWhen creating a new Portal in Oracle WebCenter, developers have the option to base that portal on a template that includes: Pre-seeded data such as pages, tools, user roles, and look-and-feel assets Specific sub-sets of page-layouts, tools, and other resources to standardize what is added to a Portal’s pages Any custom components that your team creates during development cycles Once you have identified a successful workspace and its most valuable components, leverage Oracle WebCenter’s ability to turn that custom portal into a portal template. By creating a template from your already successful portal, you are empowering your enterprise by providing a starting point for future initiatives. Your new projects, new teams, and new web pages can benefit from lessons learned and adjustments that have already been made to optimize user experiences instead of starting from scratch. ***For a complete explanation of how to work with Portal Templates, be sure to read the Fusion Middleware documentation available online.

  Read the article

• Using Ops Center to Provision Solaris using a Card-Based NIC

  - by Larry Wake

  Scott Dickson writes:  "Here's what I want to do:  I have a Sun Fire T2000 server with a Quad-GbE nxge card installed.  The only network is connected to port 2 on that card rather than the built-in network interfaces.  I want to install Solaris on it across the network, either Solaris 10 or Solaris 11." See what he did, using Oracle Enterprise Manager Ops Center 12c. [Read More]

  Read the article

• Wireless Not Working with Drivers Installed

  - by Haoran

  I'm new to Linux. I installed Ubuntu 12.10 on my old Compaq/Hp Preario V3000 to replace Windows XP. Every thing works fine except I'm getting no wireless network options in the network drop down menu. I'm using a cable at the moment. Wirless chipset is: 05:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) 08:08.0 Ethernet controller: Intel Corporation PRO/100 VE Network Connection (rev 02) I ran rfkill: 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no I also ran iwconfig and got this lo no wireless extensions. eth0 no wireless extensions. In the additional drivers it says: "Using Broadcom 802.11 Linux STA wireless driver source from bcmwl-kernel-source (proprietary)" Any help to resolve the problem would be greatly appreciated.

  Read the article

• Multi subnet in ubuntu with dnsmasq

  - by Fox Mulder

  I have a multi lan port box that install ubuntu server 11.10. I am setup network in /etc/network/interfaces file as follow: auto lo iface lo inet loopback auto eth0 iface eth0 inet static      address 192.168.128.254      netmask 255.255.255.0      network 192.168.128.0      broadcast 192.168.128.255      gateway 192.168.128.1      dns-nameservers xxxxxx auto eth1 iface eth1 inet static      address 192.168.11.1      netmask 255.255.255.0      network 192.168.11.0      broadcast 192.168.11.255 auto eth2 iface eth2 inet static      address 192.168.21.1      netmask 255.255.255.0      network 192.168.21.0      broadcast 192.168.21.255 auto eth3 iface eth3 inet static      address 192.168.31.1      netmask 255.255.255.0      network 192.168.31.0      broadcast 192.168.31.255 I am also enable the ip forward by echo 1 /proc/sys/net/ipv4/if_forward in rc.local. my dnsmasq config as follow except-interface=eth0 dhcp-range=interface:eth1,set:wifi,192.168.11.101,192.168.11.200,255.255.255.0 dhcp-range=interface:eth2,set:kids,192.168.21.101,192.168.21.200,255.255.255.0 dhcp-range=interface:eth3,set:game,192.168.31.101,192.168.31.200,255.255.255.0 the dhcp was working fine in eth1,eth2,eth3, any machine plug in the subnet can get correct subnet's ip. My problem was, each subnet machine can't ping each other. for example. 192.168.11.101 can't ping 192.168.21.101 but can ping 192.168.128.1 192.168.31.101 can't ping 192.168.21.101 but can ping 192.168.128.1 I am also try to using route add -net 192.168.11.0 netmask 255.255.255.0 gw 192.168.11.1 (and also 192.168.21.0/192.168.31.0) at this multi-lan-port machine. But still won't work. Does anyone can help ? Thanks.

  Read the article

• Ubuntu Connect Button Disabled, cannot connect

  - by CSharperWithJava

  I'm trying to connect to my school network from Ubuntu 12. The network is WPA encrypted and I can connect just fine if the network manager establishes a connection automatically. However, when I get disconnected and try to reconnect a username and password prompt pops up. The credentials are already stored and are autofilled in correctly, but the Connect button is disabled so I can't actually connect to the network. What can I do? The only guess I've found so far is the password is too short and Ubuntu is expecting a full WPA key. I don't administer the school network though so I certainly can't change that.

  Read the article

• No internet access on Windows 7 - part 2

  - by Vnuk

  This is a continuation of my previous question. The problems started when I turned on my wireless connection for the first time. Since then, every time I boot my Windows 7, my LAN connection does not have internet access. In my previous question, I got a key answer (route delete). Now my procedure to get LAN internet connectivity (local network works fine) when I boot looks like this: Power on WLAN Disconnect LAN cable Power off WLAN Execute route delete 0.0.0.0 if 11 Connect LAN cable Now my LAN connection has internet access. Another behavior that I can't explain - while my LAN connection has no internet access, Network and Sharing center refers to it as Unknown network, with a public icon. When I go through the fore mentioned procedure, it is referred to with my home WLAN network name, with status connected, and the Unknown network disappears.

  Read the article

• Internet Magic (Proxy sever) windows application

  Windows application which create proxy server to share Internet over any TCP/IP network

  Read the article

• Add a server between router and switch (production)

  - by Kossel

  I have a small office network basically like below, there are more router/pc connected in S1. As you can see, the router is doing job of DHCP, DNS. but now I wish to add a Linux server between R1 and S1, So I can monitor the network traffic and do other more advance server admin stuff. the whole office network is 192.168.1.x and people are using their computer everyday. What network configuration should the new Linux server have (both interfaces) in order to minimize the changes need in the network? tried to change R1 ip to 192.168.100.1 them add the server with FE0/0 192.168.100.1 and FE0/1 192.168.1.1 but looks cannot ping the original Router..

  Read the article

• Deep-protocol analysis of UNIX networks

  <b>developerWorks: </b>"Whether you are monitoring your network to identify performance issues, debugging an application, or have found an application on your network that you do not recognize, occasionally you need to look deep into the protocols being used on your UNIX network to understand what they are doing."

  Read the article

• How do I bridge my wireless to my wired connection?

  - by gatoatigrado

  I want to bridge the wireless connection with the wired connection. The wireless is the host and the wired is the client, so to speak. Internet sharing (inet <--> wifi <--> ethernet) I tried to bridge my ethernet connection by going to network manager edit connections wired edit IPv4 settings shared to other computers Screenshots However, it seems to automatically disconnect half a second after it says "connection established"! edit 2 got the network manager logs, it seems the address is in use. See http://pastebin.com/DjqRshxW , line 45. nm-tool output is here: http://pastebin.com/x5Aci5V1 . I tried firestarter, as mentioned in another thread, and no luck. I don't have time to bother with a dozen command line tricks, unless is copy & pasting a shell script... so please suggest ways that use GUIs and/or won't leave my computer in a confused state (e.g. disabling network manager, manually connecting to a WPA network, installing brutils, etc.). edit: one idea that would work, if it's possible -- is there a way to share connections via SSH and SOCKS5? I'd need to do this at a system-wide level though; I only know how to do it through the browser now. Then, I could run ifconfig eth0 192.168.4.1 on the computer sharing the inet, and ifconfig eth0 192.168.4.2 on the computer I'm trying to share with; I know this does work for host-to-host transfers. edit 3 If I run sudo killall dnsmasq, then nothing is using the 10.42.43.1 address the network manager sharing wants to use. But now it just takes longer to die, with error "NetworkManager[5935]: dnsmasq died with signal 9" [ http://pastebin.com/4FNtpugi ]. Looking at just the commands [ http://pastebin.com/1vrtQeWk ], maybe it's trying to route eth0 to itself? I'm not that familiar with networking things though.

  Read the article

• Changing Vim Home Directory

  - by mcaaltuntas

  Previously I've been using vim without any problems. However a few months ago our company made some network and security updates. After that whenever I plug a network cable into my laptop, it creates a network shared drive "H" with my company name and when I try to open vim it doesn't load plugins and other things that are in my vim home directory. I have found the reason but I don't know how to solve it. The problem is that these network updates changed our HOME directory. When I write: echo $HOME It prints H. Before plugging in a network cable my home was C:\Users\blabla. How can I change my HOME variable? When I run set it prints: C:\Windows\System32>set | findstr /R "^HOME" HOMEDRIVE=H: HOMEPATH=\ HOMESHARE=\\companyname\blabla\username$

  Read the article

< Previous Page | 235 236 237 238 239 240 241 242 243 244 245 246  | Next Page >