Search Results

Search found 16810 results on 673 pages for 'screen recording'.

Page 240/673 | < Previous Page | 236 237 238 239 240 241 242 243 244 245 246 247  | Next Page >

• Debian Squeeze: Trackpad on EEE PC 1000HA acts like slate

  - by CarlF

  I'm using Debian on an Asus Eee PC 1000HA. It works flawlessly, except that the built-in trackpad acts as if it was a slate. That is, if I touch the upper-left quadrant of the trackpad, the mouse pointer "teleports" to the upper left of the netbook's screen. If I touch the bottom center, the pointer teleports to the bottom center of the screen. I currently have no xorg.conf. I have tried various settings for the mouse in xorg.confs that I created, and none of them did more than disable the trackpad entirely. The trackpad works perfectly in Windows XP (shipped with the Eee) and in Ubuntu. Debian works fine with the (USB) mouse. Any suggestions? Thanks.

  Read the article

• Connecting / disconnecting DisplayPort causes crash

  - by iGadget

  I wanted to file a bug about this using ubuntu-bug xserver-xorg-video-intel, but the system prompted my to try posting here first. So here goes :-) While the situation in Ubuntu 11.10 was still somewhat workable (see UI freezes when disconnecting DisplayPort), in 12.04 (using Unity 3D) it has gotten worse. The weird part is that during the 12.04 beta's, the situation was actually improving! I was able to successfully connect and disconnect a DisplayPort monitor without the system breaking down on me. But now with 12.04 final (with all updates), it's just plain terrible. When I now connect an external monitor using the DisplayPort connector on my HP ProBook 6550b, it only works sometimes. Most times (but not always!) the screen just goes blank and the system seems to crash (not even CTRL+ALT+F1 works anymore). Only a hard shutdown by keeping the power button pressed for several seconds and then a restart gets me out of this. I suspect the chances of the system crashing become higher as the system's uptime increases, especially when there have been one or more suspend-resume cycles (although I have also experienced this bug once from a cold boot). Disconnecting is roughly the same as with 11.10 (see issue mentioned above), with the difference that if I resume from suspend, I no longer have to do a CTRL+ALT+F1, ALT+F7 cycle to get my screen back. So what more can I try? Or should I just go ahead and file the bug anyway?

  Read the article

• how to install Ubuntu on a fresh hard drive

  - by Herman Wiegman

  I attempted to install Ubuntu from a USB stick to my Intel 4 3GHz computer with 80GB HDD. The installer was doing well, then it said something to the effect of "errors on the source USB, or the target HDD" The recommendation was to download the installer again. I suspected my HDD was going bad so I figured I would investigate. What I found was a partially formatted 80GB HDD. I repartitioned it via a different computer. Now a fresh copy of the Ubuntu USB installer is not able to move past the start-up screen (it freezes). I was able to purchase a new / clean HDD, but still the fresh copy of the installer still locks up after the initial opening screen (locks up after about 2 screens worth of installations steps). Does this sounds like a HDD NTHS issue or a CPU/hardware/memory issue? or should I move to a CD image file rather than my USB stick? Now my computer is stuck... no OS.. no way to go back to Windows (upgrade OS CD only). Any insight would be greatly appreciated. Stuck in Schenectady Herman Wiegman

  Read the article

• Moving LiveMeeting admin functions to a different window

  - by Rob Farley

  I run a user group, and often host LiveMeeting sessions. I use a projector, with a crowd watching. How do I do the admin stuff (respond to Q&A, etc) on one window, and just have the video on the 'extended monitor'? I dont' want the people in the audience to see anything except the video feed, but I want to be able to watch questions come in, etc... Note: I don't have a problem extending the screen across the two monitors - I already have different stuff showing on my screen compared to the projector. I just want a way to put the LM video on Monitor 2 (projector), and the LM controls on Monitor 1.

  Read the article

• My computer will not reboot after fresh install of ubuntu 12.04LTS

  - by user170715

  I bought a new computer yesterday and it came with Windows 8. When installing Ubuntu, i choose the erase and install option thinking that Ubuntu would install easily like it did for my old laptop... After a successful install and following the instructions telling me to reboot to finish installation and remove installation media. It worked and my computer booted fine, however once I began installing updates via update manager and activating additional driver {ATI/AMD proprietary FGLRX graphics driver (post-release updates)} out of the following: Experimental AMD binary Xorg driver and kernel module ATI/AMD proprietary FGLRX graphics driver (*experimental*beta) ATI/AMD proprietary FGLRX graphics driver (post-release updates) Then reboot to finish making changes I reboot and get an error (Reboot and select proper boot device) At this point I was stuck, so I eventually reinstalled ubuntu and repeated the exacted same steps until right before i rebooted to finish making changes. However this time i used this Boot Repair tool sudo add-apt-repository ppa:yannubuntu/boot-repair sudo apt-get update sudo apt-get install -y boot-repair boot-repair After running the program i get a "boot successfully repaired" message. Then I try to reboot again and get the GNU Grub screen where it says would you like to boot: normal recovery memorytest Once it begins loading, you see the code moving across the screen then it pauses when it gets to and doesnt do anything. If someone could tell me how to fix this or get Windows 8 back soon, I'd appreciate it because like i said i just bought it yesterday and now i cant even use it.

  Read the article

• Display Problems running Ubuntu 12.04 in Windows VMware Player

  - by Alex Reynolds

  I am posting this again because I have changed to VMWare Player and I discovered something new. I am running Ubuntu 12.04 LTS (Guest) in VMWare Player 6.0.2 on Windows 7 64-bit Host. I have VMWare Tools installed properly. I am running MATE but the problem persists when I change (to and from) xfce, gnome, mate a-- and back again I had been using this for a couple of years without any graphics issues. After an Ubuntu update (typical) -- my video is corrupt and will not refresh correctly. My desktop icons are "mirrored" and when I open a terminal window (for instance) -- sometimes -- the window appears multiple times. Of course, only one is the real image. It seems to be a refresh problem. When I move an active window around the screen the "older" images "erase" and my icons (for instance) are in the correct location. For instance, I can move the terminal around a pretty corrupted window and the screen behind it is repainted correctly. NEW: Next, I got the idea to try and Remote Desktop in to the Ubuntu 12.04 LTS Guest OS from my Windows 7 64-bit Host. Once working, and connected via Win RDC -- using MATE as default in my /etc/xrdp/startws.sh -- my video is not corrupted and works fine (as in the past). Any ideas about what is going on ? or how to fix this ?

  Read the article

• Ubuntu 12.04 and Nvidia GTX 550 Ti

  - by Jim

  OK I'm currently trying to install Ubuntu x64 Server 12.04 onto the following machine: Intel Core i5-2320 3.0GHz LGA1155 6MB 8 GB DDR3 RAM, Gigabyte Z68P-DS3 S1155 Intel Z68 DDR3 ATX M/B, OCZ 60 GB SSD, 3x Samsung 2TB drives in a RAID 5 array (via M/B) Now what I think is causing the issue is the following: EVGA GeForce GTX 550 Ti 951MHz 1GB PCI-Express HDMI FPB As the server CD works in text mode I haven't had a problem with actually installing Ubuntu. Partioned with: 1GB /boot SSD, 59GB / SSD, 10GB swap RAID5, ~4TB /home RAID5 On a straight boot, you briefly see the GRUB menu, followed by a blank screen. The keyboard and mouse blink as they are initialised but no sign of life from the screen. Followed by a bit of research (otherwise known as google) ... Booted in quiet splash nomodeset Now I have a fully working linux distro at the command prompt. I then proceed to try and update the nvidia drivers with apt-get (after updating repositories etc) and rebooting. Still the same problem. I also tried reinstalling from the CD and installing said drivers in the install process before GRUB was installed, still the same symptoms. Does anybody have any solutions? I'm at my wits end here, I bought this machine to be a linux server / tinkering machine and have just spent 4-5 hours trying to just get a basic install working.

  Read the article

• Dell Upgrade to 12.04 LTS No wifi, graphic card driver and bluetooth Problem?

  - by Mattlinux1

  (Dell inspiron m5040 Upgrade to 12.04 LTS from 11.10 wifi wont work and has two bluetooth icons?) Old title of post! No Wifi/Bluetooth Problem. "Both Fixed", see below comments for bluetooth fix and see bottom answer for wifi fix. My online upgrade of 12.04 LTS, was installed to my laptop the Dell inspiron m5040, when it was done i found that my wifi did not even get picked up anymore and i now have two bluetooth icons at the top?? So what i have been doing for now is at the boot screen. I hit the use previous linux version, this works fine but also has the two bluetooth at the top. Is very thankful for any answers for this fix, Thank You. Ok bluetooth problem solved by – fossfreedom answer by deleting the other bluetooth program running in software center. Now the other problem is Wifi: just have to restart system as it works in previous linux version boot opt, but on the first boot screen opt run ubuntu it will not pick up wifi drivers. Broadcom 802.11 Linux STA wireless driverfor use with Broadcom's BCM4311-, BCM4312-, BCM4313-, BCM4321-,BCM4322-, BCM43224-, and BCM43225-, BCM43227- and BCM43228-basedhardware. And 3D-accelerated proprietary graphics driver for ATI cards. This driver is required to fully utilise the 3D potential of some ATI graphics cards, as well as provide 2D acceleration of newer cards. will not instill is there anyway for me to make a copy of the drivers via usb HDD and then put them on new upgraded version.

  Read the article

• A proper way to create non-interactive accounts?

  - by AndreyT

  In order to use password-protected file sharing in a basic home network I want to create a number of non-interactive user accounts on a Windows 8 Pro machine in addition to the existing set of interactive accounts. The users that corresponds to those extra accounts will not use this machine interactively, so I don't want their accounts to be available for logon and I don't want their names to appear on welcome screen. In older versions of Windows Pro (up to Windows 7) I did this by first creating the accounts as members of "Users" group, and then including them into "Deny logon locally" list in Local Security Policy settings. This always had the desired effect. However, my question is whether this is the right/best way to do it. The reason I'm asking is that even though this method works in Windows 8 Pro as well, it has one little quirk: interactive users from "User" group are still able to see these extra user names when they go to the Metro screen and hit their own user name in the top-right corner (i.e. open "Sign out/Lock" menu). The command list that drops out contains "Sign out" and "Lock" commands as well as the names of other users (for "switch user" functionality). For some reason that list includes the extra users from "Deny logon locally" list. It is interesting to note that this happens when the current user belongs to "Users" group, but it does not happen when the current user is from "Administrators". For example, let's say I have three accounts on the machine: "Administrator" (from "Administrators", can logon locally), "A" (from "Users", can logon locally), "B" (from "Users", denied logon locally). When "Administrator" is logged in, he can only see user "A" listed in his Metro "Sign out/Lock" menu, i.e. all works as it should. But when user "A" is logged in, he can see both "Administrator" and user "B" in his "Sign out/Lock" menu. Expectedly, in the above example trying to switch from user "A" to user "B" by hitting "B" in the menu does not work: Windows jumps to welcome screen that lists only "Administrator" and "A". Anyway, on the surface this appears to be an interface-level bug in Windows 8. However, I'm wondering if going through "Deny logon locally" setting is the right way to do it in Windows 8. Is there any other way to create a hidden non-interactive user account?

  Read the article

• Cannot boot from Yumi multiboot USB stick

  - by Amator

  I've just created a multiboot USB stick using Yumi. I tried to start my notebook (Asus K70IO) using it, but all I see is just a black screen with blinking underscore even after waiting for minutes. If during this time I remove the USB stick I get the message: "Operating system load error". How do I properly load my Yumi USB stick and use it? I've tried formatting it using Yumi's checkbox to format the stick in FAT32 too, but it didn't help. Now I tried to use Sardu 2.0.5 and met same problem: black screen and blinkin underscore, if I remove stick I see "Operating system load error" and my OS starts to boot. At the same time if I create bootable USB stick from ISO using UltraISO it boots smoothly.

  Read the article

• The battery indicator in Unity panel not showing up

  - by user61415

  I installed Ubuntu 12.04 with Wubi. Well after being completely dazzled with the amount of free content in the Software Centre, I decided to go deeper and start messing with settings. Well after changing the screen brightness the highest level I noticed that there wasn't an indicator for how much battery was left in my laptop. I looked up online on got 2 suggestions on how to fix: Right click on the Unity panel and add an indicator Set it to show in the power settings menu. Well I did both when I right click at the top menu nothing comes up and setting it to show does nothing either. Then I tried installing something in the Software Centre. I got something but when I activated it it said I had 0% power left even though I was charging and at %100 according the Light in the front of my laptop. So now I'm thinking that it doesn't even recognise my computer as a laptop which is weird because in the display settings it says my screen size is set to laptop. How can I install it? I don't know what version it is other then Ubuntu 12.04 and no matter what the icon does not appear with the

  Read the article

• OpenGL depth texture wrong

  - by CoffeeandCode

  I have been writing a game engine for a while now and have decided to reconstruct my positions from depth... but how I read the depth seems to be wrong :/ What is wrong in my rendering? How I init my depth texture in the FBO gl::BindTexture(gl::TEXTURE_2D, this->textures[0]); // Depth gl::TexImage2D( gl::TEXTURE_2D, 0, gl::DEPTH32F_STENCIL8, width, height, 0, gl::DEPTH_STENCIL, gl::FLOAT_32_UNSIGNED_INT_24_8_REV, nullptr ); gl::TexParameterf(gl::TEXTURE_2D, gl::TEXTURE_MAG_FILTER, gl::NEAREST); gl::TexParameterf(gl::TEXTURE_2D, gl::TEXTURE_MIN_FILTER, gl::NEAREST); gl::TexParameterf(gl::TEXTURE_2D, gl::TEXTURE_WRAP_S, gl::CLAMP_TO_EDGE); gl::TexParameterf(gl::TEXTURE_2D, gl::TEXTURE_WRAP_T, gl::CLAMP_TO_EDGE); gl::FramebufferTexture2D( gl::FRAMEBUFFER, gl::DEPTH_STENCIL_ATTACHMENT, gl::TEXTURE_2D, this->textures[0], 0 ); Linear depth readings in my shader Vertex #version 150 layout(location = 0) in vec3 position; layout(location = 1) in vec2 uv; out vec2 uv_f; void main(){ uv_f = uv; gl_Position = vec4(position, 1.0); } Fragment (where the issue probably is) #version 150\n uniform sampler2D depth_texture; in vec2 uv_f; out vec4 Screen; void main(){ float n = 0.00001; float f = 100.0; float z = texture(depth_texture, uv_f).x; float linear_depth = (n * z)/(f - z * (f - n)); Screen = vec4(linear_depth); // It ISN'T because I don't separate alpha } When Rendered so gamedev.stackexchange, what's wrong with my rendering/glsl?

  Read the article

• Windows 7 dual monitor setup: Wallpaper alignment

  - by Tomalak

  I have the following dual-screen set up on my Windows 7 PC: [2][1], that means my secondary monitor is on the right side of my primary monitor. Now I have a dual-screen wallpaper that should stretch across the monitors. I have set it to "Tile" mode. Problem: The wallpaper invariably starts at [1] (left edge of the image being on the left edge of [1]), and then continues on [2]. It basically splits the wrong way, producing a rather awkward look. How can I make the wallpaper appear correctly (i.e. left edge of the image being on the left edge of [2])?

  Read the article

• Desktop goes un-usable after upgrade to 12.04

  - by Tom Nail

  I have multiple Ubuntu systems connected to a KVM, one of which I recently upgraded from Ubuntu 10 to 12.04. After the upgrade, this system desktop does fine until it is allowed to go to idle (i.e., I've switched to another system on the KVM and it locks it's desktop). When I come back to it, the screen is garbled and paging across at a rate seemingly determined by the mouse. Although no pointer is visible, I can get the screen to stop paging (and just be garbled) by moving the mouse left and right. The paging will slow down and come to a stop, if I can align things carefully enough. This condition persists even when I try to go to a CLI-based login (e.g., CTRL+Alt+F1) and will continue until I reboot the machine. Unfortunately, I'm not very familiar with the Unity desktop, so I don't know where to find things to troubleshoot. A restart of lightdm doesn't change anything, so I'm wondering if this might be more hardware based( although this machine hasn't given me any trouble previously in the same setup). The .xsession-errors file has some issues with compiz, nautilus and GConf listed, but I'm not sure those are actually germane to the issue. Thanks for any help, -=Tom

  Read the article

• I can't enable extra effects in Ubuntu 10.10. Please help?

  - by jasoncruz98

  I installed Ubuntu 10.10 alongside Ubuntu 11.10 to use an older version of Compiz. On Ubuntu 11.10, Compiz was enabled by default and I didn't need to use any graphics driver to enjoy the effects. All I had to do was install CompizConfig Settings Manager and enable those extra effects. That was Compiz 0.9.6. Now, after installing Ubuntu 10.10, when I first logged in, the graphics were slow. When I dragged a window from one end of the screen to the other, the whole screen would blur up and pixelate and it would be very laggy. I tried going to System Preference Appearance and selecting Extra effects on the Visual effects tab, but all I got was "Desktop effects could not be enabled". I don't know whether I should install the Additional drivers (proprietary) because my Internet is slow and it would take a long time. Furthermore, in Ubuntu 11.10, after I installed the proprietary graphics driver, I immediately went into fallback mode and wasn't even offered an option to set my desktop session to Ubuntu 3D. I didn't need the driver to run Compiz in Ubuntu 11.10, it just ran so smoothly. But in Ubuntu 10.10, everything is so laggy. Should I install the ATI/AMD Proprietary FGLRX Graphics Driver for Ubuntu 10.10 to enable extra effects? Or is there something else wrong with my system? Here is the output of lspci -nn | grep VGA 00:02.0 VGA compatible controller [0300]: Intel Corporation Sandy Bridge Integrated Graphics Controller [8086:0116] (rev 09) 01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Device [1002:6760] Here is the output of the same command, but in Ubuntu 11.10 (in this case the one which is correct, because I don't have the Sandy Bridge Integrated graphics controller) 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) 01:00.0 VGA compatible controller [0300]: ATI Technologies Inc NI Seymour [AMD Radeon HD 6470M] [1002:6760]

  Read the article

• Hard time installing Ubuntu

  - by Nick

  I have a MSI GT780DXR that currently is booting windows 7. I've been trying to dual boot windows 7 and ubuntu for some time now. Here's specs that I think would make a difference Windows 7 500GB*2 RAID 0 hard drives. (Hardware RAID I'm not sure if it's a dedicated RAID card though) 7200RPM Nvidia GT570M Background: I tried to install 12.04 (64 bit) a few times but the Desktop live cd and pendrive boots with a black screen. I've tried wubi but it boots to a black screen as well. I then tried the alternative 12.04 (64 bit) and went through the installation all the way til partitioning. I let Ubuntu notice the raid setup and I setup my swap, /, and home drives, I used my free space to create the three partitions. I tried to resize the windows drive and it told me I couldn't and to be happy with my current setup. When I finally got past I got an error on installing GRUB 2 and decided to skip it and continued on to finish installation. When I tried to boot up I got an invalid partition table error. Windows recovery disc, and a GPARTED live cd couldn't find any hard drives. I ended up following advice and typed this into the recovery command prompt. bootrec /fixmbr bootrec /fixboot bootrec /rebuildBcd It worked and here I am now. The question is, how would I be able to dual boot windows 7 and Ubuntu 12.04 with this information? Thanks,

  Read the article

• One monitor getting spilled over into other monitor: how to do a 100% reset of gnome graphics configuration

  - by Paul Nathan

  I had to kill a VMWare process and afterwards, my monitor's configuration is buggy. I have 2 monitors in a side-by-side configuration. My right-hand monitor is the secondary monitor. Upon its right-hand side there are about 50 pixels showing from the left side of the lefthand monitor (ie, as if it was wrapped around). Further, my mouse clicks are registering as about 50 pixels sideways from where they should be. It's as if those 50 pixels between monitors got gobbled. What have I done? I've reset the screen configuration in multiple ways, using xrandr, multiple monitors app, etc. This persists in different side-by-side configurations, and also persists with another user. It does not occur with XFCE. Resetting the Window manager with the Compiz reset WM app does not fix this. I've concluded the burn-to-the-ground approach is likely the best, and would like to do a 100% reset of my graphics settings. It's an Intel integrated chipset. Removing ~/.config/monitors.xml did not work. Also, interestingly, the mouse can mouse-over the 50 errant pixels on the rhs of the right-hand monitor. I hypothesize that it's a compositing problem occurring at the layer where the background, selection, and clicks are caught. Also, inverting the right-hand monitor removes the issue, but renders the screen unusable. Even more datapoints: This happens in KDE as well Sometimes logging into Gnome and running xrandr --output DVI1 --auto resets it, but the issue immediately reappears when I press alt-tab. With Compiz Application Switch turned on, the workspace is 'pushed back' a bit, and the slice on the RHS follows it as well. I'm wondering if it's a flaw in the compiz workspace compositing configuration. I suspect the error was in the compositing configuration. I installed 11.10.

  Read the article

• Windows 8 Metro UI with Multiple Monitors -- Keep in always maximized?

  - by Jersey Dude

  Before installing Win 8 today, my plan was to keep the Metro UI up on my smaller, laptop monitor and have the classic UI running on my two larger monitors. However, in reality, as soon as I click on something in one of the classic UI monitors, the Metro UI minimizes (thus exposing the classic UI in its place). Is there any way to keep the Metro UI from minimizing when I do something in another monitor? Oddly enough, if there is an app running/suspended in the Metro Window, then the Metro UI is not minimized. If the Start screen is currently viewed, clicking in a classic window/monitor switches the Metro UI from the start screen to the last run app. Very peculiar .. Thanks

  Read the article

• How to set Laptop Brightness in Gnome and /proc on Thinkpad W510?

  - by hakre

  I can set the brightness of my laptop screen already via /proc. I can read and change the value. Now I've set the value to 33 and then I went into gnome power management and enabled the option that it should reduce the backlight brightness being on battery. That works, the screen gets darker. If I now read out the current setting from /proc it still says it's 33. So I assume that there is another node in /proc to be used to control the brightness. The node I use so far is: /proc/acpi/video/VID/LCD0/brightness I'm using the nouveau driver. With the nvida driver the brightness can not be controlled.

  Read the article

• Gigabyte GA-Z77X-D3H MB problems

  - by Hans

  I installed a new system last week. I've some issues with it. The system consists of a: Gigabyte GA-Z77X-D3H with F9 BIOS (latest) Intel Core i5 3570K proccesor Sapphire Radeon HD7850 2x 8GB Corsair 1600MHz memory OCZ Vertex 2 120G SSD Connected peripherals : 2 Samsung 940BF (1 via DVI on GFX card, 1 via an Displayport to DVI adapter) 1 Dell U2312HM monitor (displayport) Dell USB Hub (monitor) Wired mouse, wireless keyboard (logitech) Logitch G25 wheel Canon MP800 printer Okay, my issues are the following: if I plug in 1 or more monitor at DisplayPort during boot, most of the time it won't boot properly. I get an empty message screen of UEFI: only the header GIGABYTE DUEL BIOS appears. The system reboots itself, turns on for a few seconds (no video) and then reboots again. Now it starts all over again. This repeats until I remove all displayport monitors. Windows boots, and I can use them when I replug them. The graphics card has been running fine for a few weeks on an older system (intel Q6600). Another issue is; if I plug in my G25 steering wheel, the UEFI BIOS is inaccessible. It either gives the same empty UEFI screen, or the BIOS screen is rendering but crashes half way (so pieces of text and graphics are missing, and it has crashed). If I remove the G25, all is fine. To verify the graphics card is OK and the motherboard is causing these issues, I tried an NVIDIA 8800GT graphics card. This hasn't got Displayport, but it also cannot boot the BIOS with the G25 wheel plugged in. The PC also refuses to go into or out of standby. It just hangs when going into standby, and in other occasions (when it does succesfully do so) get out of standby. Power supply is OCZ StealthXStream 600W. Proccesor is 25 - 30C idle, ~55C stressed (Scythe Mugen 2). I am really puzzled what can be done to resolve this. I am not really waiting for an RMA request (otherwise I will return the MB for another type), because it will likely mean I have to wait very long before I get a replacement. Anyone else with a similar experience on this board/chipset or can help me troubleshoot this?

  Read the article

• Improve performance on Lync desktop sharing

  - by Trikks

  I'm using Lync 2010 server to handle some clients communication and screen sharing. The biggest issue is the performance with screen sharing, it is of rather high quality but the frame rate is very poor. I have been reading and searching a lot on the subject and 95% of all topics is about bandwidth, we have a 200/200 MBit Internet connection solely for this application. Also my test machines runs on an internal gigabit lan. The speeds between all boxes is hysterically fast. Next step was to ensure that there where some profiles for different bandwidths, so i registered some New-CsNetworkBandwidthPolicyProfile -Identity 50Mb_Link -Description "BW profile for 50Mb links" -AudioBWLimit 20000 -AudioBWSessionLimit 200 -VideoBWLimit 14000 -VideoBWSessionLimit 700 New-CsNetworkBandwidthPolicyProfile -Identity 100Mb_Link -Description "BW profile for 100Mb links" -AudioBWLimit 30000 -AudioBWSessionLimit 300 -VideoBWLimit 25000 -VideoBWSessionLimit 1500 Nothing fancy happend here either. Non of the test boxes have anything from Norton installed, they doesn't have any firewalls running (nor does the Lync server), all fences are down in this environment just for the testing. Is there any thing that I may have missed to improve the quality of this? Thanks

  Read the article

• XNA 2D Spritesheet drawing rendering problem

  - by user24092

  I'm making a tile-based game, using one spritesheet containing all tile graphics. Each tile has a size of 32x32 pixels. The main problem is: when I draw the tile to the screen, if the tile position x and y are not rounded or if scale is activated in spriteBatch.Draw() method (scale != 1.0f), I get some lines of adjacent tiles on the spritesheet into the current tile drawed. I already tried setting SamplerState to PointClamp, removing AntiAlias, but still doesn't work. Here I'll show images of some tests that I made, with a test sprite sheet that I've created (I made a 9x9 spritesheet, with each sprite of size 32x32 containing a unique solid color). Tests: http://img6.imageshack.us/img6/5946/testsqj.png SpriteSheet used: http://imageshack.us/a/img821/1341/tilesm.png Already tried to remove anti-alias, set PointClamp as sampler state, but still getting this issue, XNA keeps drawing part of the adjacent pixels of the texture on the screen. What I want is to get the correct area of the tilesheet texture (as seen in the first test, that gets just the yellow pixels). My question is: Is there any way that I can fix this, WITHOUT adding tile spacing or any other modification involving the tilesheet? Maybe disabling a texture filtering that is done by XNA, or something like that.

  Read the article

• Views : ViewControllers, many to one, or one to one?

  - by conor

  I have developed an Android application where, typically, each view (layout.xml) displayed on the screen has it's own corresponding fragment (for the purpose of this question I may refer to this as a ViewController). These views and Fragments/ViewControllers are appropriately named to reflect what they display. So this has the effect of allowing the programmer to easily pinpoint the files associated with what they see on any given screen. The above refers to the one to one part of my question. Please note that with the above there are a few exceptions where very similar is displayed on two views so the ViewController is used for two views. (Using a simple switch (type) to determine what layout.xml file to load) On the flip side. I am currently working on the iOS version of the same app, which I didn't develop. It seems that they are adopting more of a one-to-many (ViewController:View) approach. There appears to be one ViewController that handles the display logic for many different types of views. In the ViewController are an assortment of boolean flags and arrays of data (to be displayed) that are used to determine what view to load and how to display it. This seems very cumbersome to me and coupled with no comments/ambiguous variable names I am finding it very difficult to implement changes into the project. What do you guys think of the two approaches? Which one would you prefer? I'm really considering putting in some extra time at work to refactor the iOS into a more 1:1 oriented approach. My reasoning for 1:1 over M:1 is that of modularity and legibility. After all, don't some people measure the quality of code based on how easy it is for another developer to pick up the reigns or how easy it is to pull a piece of code and use it somewhere else?

  Read the article

• bash shell script which adds output of commands

  - by John Kube

  Let's say I have a command called foo which prints a number to the screen when called: $foo 3 Let's also say I have another command called bar which prints another number to the screen when called: $bar 5 I'm looking to write a shell script which will add together the output of foo and bar. How would I do that? (The outputs from the commands are not known ahead of time. They just so happen to have been 3 and 5 the last time they were run. They could have been something else.) Thanks!

  Read the article

• Set resolution of unattached display in OS X?

  - by Brad

  I have an HDTV that I'm hooking up via DVI to HDMI from my Mac mini. In my struggle to eliminate overscan I managed to set the screen resolution to something not supported by the tv. How do I change the resolution without that screen attached? Specifically my tv says it's "720p and 1366 x 768 Resolution". The 720p resolution option in OS X made for a ton of overscan (couldn't see menubar or dock at all). So I tried something x 768 and managed to shoot myself in the foot with an unsupported resolution. I thought it was okay to experiment since a resolution change times out if you don't accept it. Apparently that didn't happen for some reason. I've already deleted the com.apple.windowserver.plist in /Library/Preferences as I saw suggested in other places, with no effect.

  Read the article

< Previous Page | 236 237 238 239 240 241 242 243 244 245 246 247  | Next Page >