Search Results

Search found 29064 results on 1163 pages for 'network management'.

Page 241/1163 | < Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >

  • Measuring cumulative network statistics per user or per process

    - by zsimpson
    I've been googling for hours -- Under Linux I want to know the cumulative bytes sent and received by user or by process over all ip protocols. The best I've found in my searches is that it's possible to use iptables to mark packets for a user, for example: iptables -t mangle -A OUTPUT -p tcp -m owner --uid-owner test -j MARK --set-mark 1 It appears that "tc" can then shape traffic with that but I just want the statistic -- I don't want to shape the traffic. I want something like: "user U has transmitted used XMB since time Y". I can't figure out how to get statistics from these marked packets. Also, I've looked at nethogs but they seem to be measuring the instantaneous flow and I need cumulative counts. Anyone have ideas?

    Read the article

  • Using Visual Studio for open source projects (projects management & legal issues)

    - by Goofy
    Hello! I'm working on small open source project for developed Windows. I created new project using Visual Studio wizard and now I want to publish it using subversion and develop it with friends. What projects' configuration files I have to add to repository to make my friends able to download current project's revision and open it in Visual Studio? List item University where I study is a member of Microsoft Academy Alliance project, which make students able to download legal copies of many Microsoft's products. Can I use this copy to develop open source project and publish created code in Internet?

    Read the article

  • Correct way of bringing network interface down in linux

    - by Karolis T.
    For example: $ ifconfig dummy0 up $ ifconfig dummy0 "192.168.1.190 netmask 255.255.255.0" Calling ifconfig with no parameters shows the interface dummy0 Link encap:Ethernet HWaddr b6:1f:f3:92:6d:20 inet addr:192.168.1.190 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::b41f:f3ff:fe92:6d20/64 Scope:Link UP BROADCAST RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:1050 (1.0 KiB) How can I bring the interface down so that it doesn't show up in ifconfig ifconfig -a ifconfig dummy0 without rmmod dummy because dummy is used just for example purposes. If there is no way to do that, what "throw-away" IP could I set to it and be safe from any trouble? like $ ifconfig dummy0 down $ ifconfig dummy0 0.0.0.0

    Read the article

  • JavaScript Resource Management Design Pattern

    - by Adam
    As a web developer, a common problem I find myself tackling is waiting for something to load before doing something else. In particular, I often hide (using either display: none; or visibility: hidden; depending on the situation) elements while waiting for a background image or a CSS file to load. Consider this example from Last.FM. They overlay a semi-transparant PNG over each album art image so that it looks like it's inside a jewel-case. They let it load when it loads, so depending on your internet speed, you may see the art image by itself (without the overlay) temporarily. In this case, the album art looks fine without the jewel-case effect. But in similar situations, I have found that I don't want the user to see the site's design mangled as resources incrementally load. So, in rare cases I have hidden everything from the user until the whole kit and kaboodle has loaded. But this is often a pain to write out, and may force the user to wait for a pretty long time to see anything (besides "loading..." text). I can think of (and have used on occasion) some obvious solutions/compromises: Use some inline CSS so that as certain parts of the DOM load and render, they will immediately have the correct size/position/etc. Immediately render the navigation part of the site, so that if the user wanted to use the current page purely to get somewhere else, they don't have to wait for the rest to load. Load pixelated images first as placeholders for layout while lazy-loading higher quality images as replacements. Something quirky like using a cute animated gif to distract the user during a "loading..." phase. Show useful information as a reference while loading the full UI. (Something akin to Gmail Inbox Preview, etc.) (Sorry if my question was basically just asked and answered...) Despite all of these ideas, I still find myself hoping there are better ways of doing some of these things. So I guess what I'm looking for is some inspiration and/or any creative ways of dealing with this problem that you guys may have seen out in the wild.

    Read the article

  • Extremely slow network directory subfolder listing from QNAP NAS in OS X

    - by Josh Newman
    Having an issue where I have a folder on a QNAP NAS (TS-439P II+) with over 68,000 subfolders within it. I can browse it quickly and almost instantaneously within Windows 7 via samba, however in OSX 10.6.8, it takes nearly 10+ minutes to display the subfolders, using both samba and AFP. Hoping there is an easy solution - we can't break the folders into smaller subfolders due to a requirement of proprietary software that accesses the sub folders. I've tried the fixes suggested here, which don't seem to help: http://www.macwindows.com/snowleopard-filesharing.html#030311b

    Read the article

  • partial entity loading and management in silverlight / wcf ria

    - by Dan Wray
    I have a Silverlight 4 app which pulls entities down from a database using WCF RIA services. These data objects are fairly simple, just a few fields but one of those fields contains binary data of an arbitrarily size. The application needs access to this data basically asap after a user has logged in, to display in a list, enable selection etc. My problem is because of the size of this data, the load times are not acceptable and can approach the default timeout of the RIA service. I'd like to somehow partially load the objects into my local data context so that I have the IDs, names etc but not the binary data. I could then at a later point (ie when it's actually needed) populate the binary fields of those objects I need to display. Any suggestions on how to accomplish this would be welcome. Another approach which has occurred to me whilst writing this question (how often does that happen?!) is that I could move the binary data into a seperate database table joined to the original record 1:1 which would allow me to make use of RIA's lazy loading on that binary data. again.. comments welcome! Thanks.

    Read the article

  • Database connection management in Spring

    - by ria
    Do we have to explicitly manage database resources when using Spring Framework.. liking closing all open connections etc? I have read that Spring relieves developer from such boiler plate coding... This is to answer an error that I am getting in a Spring web app: org.springframework.jdbc.CannotGetJdbcConnectionException: Could not get JDBC Connection; nested exception is java.sql.SQLException: ORA-00020: maximum number of processes (150) exceeded The jdbcTemplate is configured in the xml file and the DAO implementation has reference to this jdbcTemplate bean which is used to query the database.

    Read the article

  • How can I connect my Xbox to my Mac on my network

    - by codecowboy
    I have a wireless router/modem (Router 1) in my living room. This is connected to the internet (cable). Wireless is disabled as the router has a terrible wireless range. My Xbox is connected via ethernet to Router 1. Another LAN output from Router 1 connects to a powerline adapter. Router 1 acts as a DHCP server on 192.168.0.x and has the IP 192.168.0.1 In a second room I have Router 2. This has the powerline feed from Router 1 going into the WAN socket. This router runs the Tomato Firmware and acts as a wireless router for the rest of the house using the IP range 192.168.1.x. Router 2 IP is 192.168.1.1. My Mac is connected to Router 2 using a LAN cable and has the IP 192.168.0.133. Several mobile devices need wireless access. I want an ethernet connection to my Mac, not wireless. I should be able to use software like Connect360 to share media from my Mac to the XBox but the XBox does not see my Mac. I can ping 192.168.0.1 from the Mac. Is this possible using my current setup? If so, how?

    Read the article

  • 3 Servers, 2 Work Fine, One Has Network Issues

    - by ScaleOvenStove
    i have 3 servers, all relatively the same hardware/config, etc. I run some data pulls on all 3, and on 2 of them, they have 1 nic, and they work fine. On the other , there are 2 nics, and unless they are both plugged in or teamed, the processes time out. Any ideas on why this would be? It doesn't make sense to me, as the other two work fine with 1 nic and don't time out when running the same processes.

    Read the article

  • Best way to connect a desktop computer to a 3g network

    - by dbyrne
    A friend of mine is moving to a building with no Internet connectivity. Ethernet and wifi are out of the question. What is the best way for him to get his desktop connected? The most obvious solution is for him to get an unlimited 3G data plan. What is the best way for him to set this up? I am assuming he should get something like Verizon's MiFi 3G access point, but does this have an ethernet jack?

    Read the article

  • Network latency and speed of light

    - by James
    This was kinda of covered by the following Is minimum latency fixed by the speed of light? , but i would like to add the follow up a bit. The scenario is as follows; we have two opposing sites one on the West Coast of the US and one in Ireland. The customer is in central Europe, and has requested a latency test. Ireland gives responses of ~65-70ms. However the West Coast guys claim to be faster with a response of 60ms. Now a quick check says that light in fiber would take about 42ms to make the trip to the States and 8.5ms to Ireland. So obviously this is a single hop and does not include routers, switches, firewalls, protocol overhead etc. Would I be right to call BS on their figures? As a final note I tested a ping to Google IP address that was allegedly on the west coast from a site that covered a similar distance and was amazed to get a response time of 20ms. Suggesting ICMP packets that travel twice the speed of light. So A) what am I missing B) Am I right to suspect shenanigans? UPDATE: Guys thanks so far for your help and I have been reading various previous questions on this. About 5 years I had an issue where the hop from the UK to Ireland added 10ms of latency no matter what we did. In the end I moved the servers; So imagine my surprise when I have guys that claim they are 5ms faster with a transatlantic trip. So again should I call BS? Oh and assume both sites are normal mortals that don't have access to Google magical routing, warp dives or flux capacitors. :)

    Read the article

  • Windows 7 - store network password

    - by disserman
    Windows 7 keeps asking for a password every time I mount a webdav. I don't want to store a password in a .bat file because it's so insecure. Is there any way to force system store it? Manually adding credentials in user manager helps storing passwords for SMB shares but for webdav doesn't. btw, as far as I remember, Vista had the same problems.

    Read the article

  • Are memory leaks really something to worry about?

    - by chuck final
    I came across this post today, arguably debatable/wrong somewhat, but worth a shot looking over: http://andyharglesiscodebase.wordpress.com/2013/11/01/why-programmers-shouldnt-worry-about-memory-leaks/ The poster claims that modern OSes automatically have garbage collection implemented in the kernel memory, and that any unfreed user heap memory is managed during "post partum cleanup". It seems like rubbish, but I can't be 100% sure since I am not that knowledgeable on the kernel's memory management setup, etc.

    Read the article

  • html5 cache -> "network: *" doesn't work

    - by Greg
    Hello all, I am trying a simple test with the html 5 cache. Here is a simple web page : <!DOCTYPE html> <html manifest="test.manifest"> <head> </head> <body> <img src="http://www.somewebsite.com/picture.jpg"/> </body> </html> With the following manifest : CACHE MANIFEST #v0.1 NETWORK: http://www.somewebsite.com/ This work fine, the picture is displayed. My problem is that I won't be able to know from where the picture will come. Here comes the online whitelist wildcard flag, that is supposed to solve my problem. But with the manifest : CACHE MANIFEST #v0.1 NETWORK: * The image is not displayed (tested on safari / safari mobile / firefox). What is not working ? Is there another way to turn the online whitelist wildcard flag on ?

    Read the article

  • Disable option never goes away for network adapters

    - by mathee
    Hi, guys, I'm running Windows 7. Whenever I disable the wireless adapter, the "Disable" option does not change to "enable". Similarly, for the "Local Area Connection", when I click on "Disable", the adapter gets disabled, but the "Disable" option remains. In summary, I am never offered the option to enable an adapter.

    Read the article

  • Wireless network relay?

    - by IPX Ares
    Is there hardware (links would be great) that can connect to the wireless internet already in my house and provide hard links to other hardware? Basically the problem is that my basement is not wired up to let me hook up my cable modem. I have some electronics that do not have wireless and need a LAN wire. Is there something I could plug in downstairs to act as a relay hub?

    Read the article

  • SafeOffice 500 - how to enable VPN access to another network (out)

    - by Dani
    Hi, I have a safe office 500 box at my edge. (checkpoint's hardware firewall) I'm trying to connect to another office VPN using windows 7 pptp connection. It fails (saying something about enabling GRE). (after authenticating, hangs for a while, than give the error message.) Using the same computer with direct internet access (not behind the firewalls) works fine and I get connected. how do I setup the safe office to enable me to use vpn (pptp) out connections.

    Read the article

  • 4 - 7 second delay accessing Mysql across the network

    - by Kristiaan
    Hello, our company has recently purchased a new server with the intention of replacing our aging database server. its a full 64bit 2008 enterprise system, i have got the basic server setup and configured and then installed the 64bit version of mysql on the server, this has then been configured to match where possible our existing server as much as it can. however i have noticed that when it was swapped with the production database server our software systems had an increased delay accessing the mysql database this was anything beween 4 - 7 seconds. i have tried disabling TOE, IPv6 and a few other suggested soultions to this but so far cannot find out where this slowdown is coming from. replacing the server with the production one and the delay goes away. in terms of software and hardware the servers are not very identical at all due to one being windows 2003 std with a 32bit server and the new one being windows 2008 enterprise with a 64bit server. thanks Kris

    Read the article

  • System Reserved partition no longer marked as System

    - by Mark
    I recently posted a question to Super User about accidentally marking my external HDD's partition as Active and how I could undo my accidental mistake. I followed the instructions provided and they worked fine. This involved some command line magic and from what I understand, I did not have to really do this, but I just wanted to get things back to how they were originally. After making the fix things went back to normal in disk management. After I restarted my computer though i had an issue: BOOTMGR is missing Press Ctrl+Alt+Del to restart Rugh roh! I brought my laptop to work so I could search for a solution on my work computer and I found a nice guide on fixing the issue. To summarize the instructions, I had to reboot with my Windows 7 install disc and click the Repair button. Once there I could then repair the start-up options. One of the commenters on the site claimed you need to do this twice, as the first time the "repair" doesn't actually fix it. I found this to be true as well. I tried to repair it and it did some work, then rebooted. I then got the same error again. I booted from the CD again and repaired the start-up options then after this second time Windows started to boot up. Before the restart I got a nice info window telling me that it did make repairs to the boot info (this was promising). I've been using Windows 7 for a few days now with no problem, but I just recently noticed that I now can see the System Reserved partition in Computer: (click for full size) I immediately went to disk management to see what was up. I noticed that my System Reserved partition is no longer marked as System and instead I believe the repair operation made my C: drive the system partition. I'm not fully aware of what the System partition really is but I briefly read that its a Windows 7 thing that gets created on install of Win7 that writes some BitLocker encryption stuff to a isolated partition as well as some boot files. (click for full size) How can I undo this and make the System Partition marked as System instead of my OS C: partition? How can I make it so that I don't see this partition in Computer (I believe fixing #1 will fix this) What are the implications of what the current state is and the fact that I can now browse into this new partition? Thanks in advance.

    Read the article

  • infiniband network between 3 servers

    - by grumpf
    Let's say I have 3 different servers, each one with an infiniband card. Each card has 2 different ports. (I don't know about the model yet) Is it possible to create 3 different networks and to allow the 3 servers to communicate with each other without any problems? (and any spof). I guess I just have to setup the /etc/hosts correctly. I really don't know about infiniband, so please help me :) Thanks in advance. EDIT: Point is to NOT USE a switch!

    Read the article

< Previous Page | 237 238 239 240 241 242 243 244 245 246 247 248  | Next Page >